| Age | Commit message (Collapse) | Author |
|---|
|
panels
The eDP link rate reported by the DP_MAX_LINK_RATE dpcd register (0xa) is
contradictory to the highest rate supported reported by
EDID (0xc = LINK_RATE_RBR2). The effects of this compounded with commit
'4a8ca46bae8a ("drm/amd/display: Default max bpc to 16 for eDP")' results
in no display modes being found and a dark panel.
For now, simply force the maximum supported link rate for the eDP attached
2018 15" Apple Retina panels.
Additionally, we must also check the firmware revision since the device ID
reported by the DPCD is identical to that of the more capable 16,1,
incorrectly quirking it. We also use said firmware check to quirk the
refreshed 15,1 models with Vega graphics as they use a slightly newer
firmware version.
Tested-by: Aun-Ali Zaidi <admin@kodeit.net>
Reviewed-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Aun-Ali Zaidi <admin@kodeit.net>
Signed-off-by: Aditya Garg <gargaditya08@live.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org
|
|
[Why]
This change causes regression, that prevents some systems
from lighting up internal displays.
[How]
Revert this patch until a new solution is ready.
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Reviewed-by: Charlene Liu <Charlene.Liu@amd.com>
Acked-by: Stylon Wang <stylon.wang@amd.com>
Signed-off-by: Zhan Liu <Zhan.Liu@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org
|
|
[Why]
The original latencies were causing underflow in some modes.
Resolution: 2880x1620@60p when HDR enable
[How]
1. Replace with the up-to-date watermark values based on new measurments
2. Correct the ddr_wm_table name to DDR5 on DCN31
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Reviewed-by: Aric Cyr <Aric.Cyr@amd.com>
Acked-by: Stylon Wang <stylon.wang@amd.com>
Signed-off-by: Paul Hsieh <paul.hsieh@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org
|
|
[Why]
There is underflow / visual corruption DCN301, for high
bandwidth MST DSC configurations such as 2x1440p144 or 2x4k60.
[How]
Use up-to-date watermark values for DCN301.
Reviewed-by: Zhan Liu <zhan.liu@amd.com>
Signed-off-by: Agustin Gutierrez <agustin.gutierrez@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org
|
|
We observed a GPU hang when querying GMC CG state(i.e.,
cat amdgpu_pm_info) on cyan skillfish. Acctually, cyan
skillfish doesn't support any CG features.
Just prevent it from accessing GMC CG registers.
Signed-off-by: Lang Yu <Lang.Yu@amd.com>
Reviewed-by: Lijo Lazar <lijo.lazar@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org
|
|
This will cause misconfigured systems to not run the GPU suspend
routines.
* In APUs that are properly configured system will go into s2idle.
* In APUs that are intended to be S3 but user selects
s2idle the GPU will stay fully powered for the suspend.
* In APUs that are intended to be s2idle and system misconfigured
the GPU will stay fully powered for the suspend.
* In systems that are intended to be s2idle, but AMD dGPU is also
present, the dGPU will go through S3
Signed-off-by: Mario Limonciello <mario.limonciello@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
This will be used to help make decisions on what to do in
misconfigured systems.
v2: squash in semicolon fix from Stephen Rothwell
Signed-off-by: Mario Limonciello <mario.limonciello@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
Leon reported NULL pointer deref with nowait support:
[ 15.123761] device-mapper: raid: Loading target version 1.15.1
[ 15.124185] device-mapper: raid: Ignoring chunk size parameter for RAID 1
[ 15.124192] device-mapper: raid: Choosing default region size of 4MiB
[ 15.129524] BUG: kernel NULL pointer dereference, address: 0000000000000060
[ 15.129530] #PF: supervisor write access in kernel mode
[ 15.129533] #PF: error_code(0x0002) - not-present page
[ 15.129535] PGD 0 P4D 0
[ 15.129538] Oops: 0002 [#1] PREEMPT SMP NOPTI
[ 15.129541] CPU: 5 PID: 494 Comm: ldmtool Not tainted 5.17.0-rc2-1-mainline #1 9fe89d43dfcb215d2731e6f8851740520778615e
[ 15.129546] Hardware name: Gigabyte Technology Co., Ltd. X570 AORUS ELITE/X570 AORUS ELITE, BIOS F36e 10/14/2021
[ 15.129549] RIP: 0010:blk_queue_flag_set+0x7/0x20
[ 15.129555] Code: 00 00 00 0f 1f 44 00 00 48 8b 35 e4 e0 04 02 48 8d 57 28 bf 40 01 \
00 00 e9 16 c1 be ff 66 0f 1f 44 00 00 0f 1f 44 00 00 89 ff <f0> 48 0f ab 7e 60 \
31 f6 89 f7 c3 66 66 2e 0f 1f 84 00 00 00 00 00
[ 15.129559] RSP: 0018:ffff966b81987a88 EFLAGS: 00010202
[ 15.129562] RAX: ffff8b11c363a0d0 RBX: ffff8b11e294b070 RCX: 0000000000000000
[ 15.129564] RDX: 0000000000000000 RSI: 0000000000000000 RDI: 000000000000001d
[ 15.129566] RBP: ffff8b11e294b058 R08: 0000000000000000 R09: 0000000000000000
[ 15.129568] R10: 0000000000000000 R11: 0000000000000000 R12: ffff8b11e294b070
[ 15.129570] R13: 0000000000000000 R14: ffff8b11e294b000 R15: 0000000000000001
[ 15.129572] FS: 00007fa96e826780(0000) GS:ffff8b18deb40000(0000) knlGS:0000000000000000
[ 15.129575] CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033
[ 15.129577] CR2: 0000000000000060 CR3: 000000010b8ce000 CR4: 00000000003506e0
[ 15.129580] Call Trace:
[ 15.129582] <TASK>
[ 15.129584] md_run+0x67c/0xc70 [md_mod 1e470c1b6bcf1114198109f42682f5a2740e9531]
[ 15.129597] raid_ctr+0x134a/0x28ea [dm_raid 6a645dd7519e72834bd7e98c23497eeade14cd63]
[ 15.129604] ? dm_split_args+0x63/0x150 [dm_mod 0d7b0bc3414340a79c4553bae5ca97294b78336e]
[ 15.129615] dm_table_add_target+0x188/0x380 [dm_mod 0d7b0bc3414340a79c4553bae5ca97294b78336e]
[ 15.129625] table_load+0x13b/0x370 [dm_mod 0d7b0bc3414340a79c4553bae5ca97294b78336e]
[ 15.129635] ? dev_suspend+0x2d0/0x2d0 [dm_mod 0d7b0bc3414340a79c4553bae5ca97294b78336e]
[ 15.129644] ctl_ioctl+0x1bd/0x460 [dm_mod 0d7b0bc3414340a79c4553bae5ca97294b78336e]
[ 15.129655] dm_ctl_ioctl+0xa/0x20 [dm_mod 0d7b0bc3414340a79c4553bae5ca97294b78336e]
[ 15.129663] __x64_sys_ioctl+0x8e/0xd0
[ 15.129667] do_syscall_64+0x5c/0x90
[ 15.129672] ? syscall_exit_to_user_mode+0x23/0x50
[ 15.129675] ? do_syscall_64+0x69/0x90
[ 15.129677] ? do_syscall_64+0x69/0x90
[ 15.129679] ? syscall_exit_to_user_mode+0x23/0x50
[ 15.129682] ? do_syscall_64+0x69/0x90
[ 15.129684] ? do_syscall_64+0x69/0x90
[ 15.129686] entry_SYSCALL_64_after_hwframe+0x44/0xae
[ 15.129689] RIP: 0033:0x7fa96ecd559b
[ 15.129692] Code: ff ff ff 85 c0 79 9b 49 c7 c4 ff ff ff ff 5b 5d 4c 89 e0 41 5c \
c3 66 0f 1f 84 00 00 00 00 00 f3 0f 1e fa b8 10 00 00 00 0f 05 <48> 3d 01 f0 ff \
ff 73 01 c3 48 8b 0d a5 a8 0c 00 f7 d8 64 89 01 48
[ 15.129696] RSP: 002b:00007ffcaf85c258 EFLAGS: 00000206 ORIG_RAX: 0000000000000010
[ 15.129699] RAX: ffffffffffffffda RBX: 00007fa96f1b48f0 RCX: 00007fa96ecd559b
[ 15.129701] RDX: 00007fa97017e610 RSI: 00000000c138fd09 RDI: 0000000000000003
[ 15.129702] RBP: 00007fa96ebab583 R08: 00007fa97017c9e0 R09: 00007ffcaf85bf27
[ 15.129704] R10: 0000000000000001 R11: 0000000000000206 R12: 00007fa97017e610
[ 15.129706] R13: 00007fa97017e640 R14: 00007fa97017e6c0 R15: 00007fa97017e530
[ 15.129709] </TASK>
This is caused by missing mddev->queue check for setting QUEUE_FLAG_NOWAIT
Fix this by moving the QUEUE_FLAG_NOWAIT logic to under mddev->queue check.
Fixes: f51d46d0e7cb ("md: add support for REQ_NOWAIT")
Reported-by: Leon Möller <jkhsjdhjs@totally.rip>
Tested-by: Leon Möller <jkhsjdhjs@totally.rip>
Cc: Vishal Verma <vverma@digitalocean.com>
Signed-off-by: Song Liu <song@kernel.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl
Pull pin control fixes from Linus Walleij:
"Most interesting and urgent is the Intel stuff affecting Chromebooks
and laptops.
- Fix up group name building on the Intel Thunderbay
- Fix interrupt problems on the Intel Cherryview
- Fix some pin data on the Sunxi H616
- Fix up the CONFIG_PINCTRL_ST Kconfig sort order as noted during the
merge window
- Fix an unexpected interrupt problem on the Intel Sunrisepoint
- Fix a glitch when updating IRQ flags on all Intel pin controllers
- Revert a Zynqmp patch to unify the pin naming, let's find some
better solution
- Fix some error paths in the Broadcom BCM2835 driver
- Fix a Kconfig problem pertaining to the BCM63XX drivers
- Fix the regmap support in the Microchip SGPIO driver"
* tag 'pinctrl-v5.17-2' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl:
pinctrl: microchip-sgpio: Fix support for regmap
pinctrl: bcm63xx: fix unmet dependency on REGMAP for GPIO_REGMAP
pinctrl: bcm2835: Fix a few error paths
pinctrl: zynqmp: Revert "Unify pin naming"
pinctrl: intel: Fix a glitch when updating IRQ flags on a preconfigured line
pinctrl: intel: fix unexpected interrupt
pinctrl: Place correctly CONFIG_PINCTRL_ST in the Makefile
pinctrl: sunxi: Fix H616 I2S3 pin data
pinctrl: cherryview: Trigger hwirq0 for interrupt-lines without a mapping
pinctrl: thunderbay: rework loops looking for groups names
pinctrl: thunderbay: comment process of building functions a bit
|
|
Do not try to use any SKB fields after the packet has been passed up in the
receive stack.
Reported-by: kernel test robot <lkp@intel.com>
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Steen Hegelund <steen.hegelund@microchip.com>
Link: https://lore.kernel.org/r/20220202083039.3774851-1-steen.hegelund@microchip.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/saeed/linux
Saeed Mahameed says:
====================
mlx5 fixes 2022-02-01
This series provides bug fixes to mlx5 driver.
Please pull and let me know if there is any problem.
Sorry about the long series, but I had to move the top two patches from
net-next to net to help avoiding a build break when kspp branch is merged
into linus-next on next merge window.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add a config option CONFIG_FRAMEBUFFER_CONSOLE_LEGACY_ACCELERATION to
enable bitblt and fillrect hardware acceleration in the framebuffer
console. If disabled, such acceleration will not be used, even if it is
supported by the graphics hardware driver.
If you plan to use DRM as your main graphics output system, you should
disable this option since it will prevent compiling in code which isn't
used later on when DRM takes over.
For all other configurations, e.g. if none of your graphic cards support
DRM (yet), DRM isn't available for your architecture, or you can't be
sure that the graphic card in the target system will support DRM, you
most likely want to enable this option.
In the non-accelerated case (e.g. when DRM is used), the inlined
fb_scrollmode() function is hardcoded to return SCROLL_REDRAW and as such the
compiler is able to optimize much unneccesary code away.
In this v3 patch version I additionally changed the GETVYRES() and GETVXRES()
macros to take a pointer to the fbcon_display struct. This fixes the build when
console rotation is enabled and helps the compiler again to optimize out code.
Signed-off-by: Helge Deller <deller@gmx.de>
Cc: stable@vger.kernel.org # v5.10+
Signed-off-by: Helge Deller <deller@gmx.de>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: https://patchwork.freedesktop.org/patch/msgid/20220202135531.92183-4-deller@gmx.de
|
|
This reverts commit 39aead8373b3c20bb5965c024dfb51a94e526151.
Revert the first (of 2) commits which disabled scrolling acceleration in
fbcon/fbdev. It introduced a regression for fbdev-supported graphic cards
because of the performance penalty by doing screen scrolling by software
instead of using the existing graphic card 2D hardware acceleration.
Console scrolling acceleration was disabled by dropping code which
checked at runtime the driver hardware capabilities for the
BINFO_HWACCEL_COPYAREA or FBINFO_HWACCEL_FILLRECT flags and if set, it
enabled scrollmode SCROLL_MOVE which uses hardware acceleration to move
screen contents. After dropping those checks scrollmode was hard-wired
to SCROLL_REDRAW instead, which forces all graphic cards to redraw every
character at the new screen position when scrolling.
This change effectively disabled all hardware-based scrolling acceleration for
ALL drivers, because now all kind of 2D hardware acceleration (bitblt,
fillrect) in the drivers isn't used any longer.
The original commit message mentions that only 3 DRM drivers (nouveau, omapdrm
and gma500) used hardware acceleration in the past and thus code for checking
and using scrolling acceleration is obsolete.
This statement is NOT TRUE, because beside the DRM drivers there are around 35
other fbdev drivers which depend on fbdev/fbcon and still provide hardware
acceleration for fbdev/fbcon.
The original commit message also states that syzbot found lots of bugs in fbcon
and thus it's "often the solution to just delete code and remove features".
This is true, and the bugs - which actually affected all users of fbcon,
including DRM - were fixed, or code was dropped like e.g. the support for
software scrollback in vgacon (commit 973c096f6a85).
So to further analyze which bugs were found by syzbot, I've looked through all
patches in drivers/video which were tagged with syzbot or syzkaller back to
year 2005. The vast majority fixed the reported issues on a higher level, e.g.
when screen is to be resized, or when font size is to be changed. The few ones
which touched driver code fixed a real driver bug, e.g. by adding a check.
But NONE of those patches touched code of either the SCROLL_MOVE or the
SCROLL_REDRAW case.
That means, there was no real reason why SCROLL_MOVE had to be ripped-out and
just SCROLL_REDRAW had to be used instead. The only reason I can imagine so far
was that SCROLL_MOVE wasn't used by DRM and as such it was assumed that it
could go away. That argument completely missed the fact that SCROLL_MOVE is
still heavily used by fbdev (non-DRM) drivers.
Some people mention that using memcpy() instead of the hardware acceleration is
pretty much the same speed. But that's not true, at least not for older graphic
cards and machines where we see speed decreases by factor 10 and more and thus
this change leads to console responsiveness way worse than before.
That's why the original commit is to be reverted. By reverting we
reintroduce hardware-based scrolling acceleration and fix the
performance regression for fbdev drivers.
There isn't any impact on DRM when reverting those patches.
Signed-off-by: Helge Deller <deller@gmx.de>
Acked-by: Geert Uytterhoeven <geert@linux-m68k.org>
Acked-by: Sven Schnelle <svens@stackframe.org>
Cc: stable@vger.kernel.org # v5.10+
Signed-off-by: Helge Deller <deller@gmx.de>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: https://patchwork.freedesktop.org/patch/msgid/20220202135531.92183-3-deller@gmx.de
|
|
TODO list)"
This reverts commit b3ec8cdf457e5e63d396fe1346cc788cf7c1b578.
Revert the second (of 2) commits which disabled scrolling acceleration
in fbcon/fbdev. It introduced a regression for fbdev-supported graphic
cards because of the performance penalty by doing screen scrolling by
software instead of using the existing graphic card 2D hardware
acceleration.
Console scrolling acceleration was disabled by dropping code which
checked at runtime the driver hardware capabilities for the
BINFO_HWACCEL_COPYAREA or FBINFO_HWACCEL_FILLRECT flags and if set, it
enabled scrollmode SCROLL_MOVE which uses hardware acceleration to move
screen contents. After dropping those checks scrollmode was hard-wired
to SCROLL_REDRAW instead, which forces all graphic cards to redraw every
character at the new screen position when scrolling.
This change effectively disabled all hardware-based scrolling acceleration for
ALL drivers, because now all kind of 2D hardware acceleration (bitblt,
fillrect) in the drivers isn't used any longer.
The original commit message mentions that only 3 DRM drivers (nouveau, omapdrm
and gma500) used hardware acceleration in the past and thus code for checking
and using scrolling acceleration is obsolete.
This statement is NOT TRUE, because beside the DRM drivers there are around 35
other fbdev drivers which depend on fbdev/fbcon and still provide hardware
acceleration for fbdev/fbcon.
The original commit message also states that syzbot found lots of bugs in fbcon
and thus it's "often the solution to just delete code and remove features".
This is true, and the bugs - which actually affected all users of fbcon,
including DRM - were fixed, or code was dropped like e.g. the support for
software scrollback in vgacon (commit 973c096f6a85).
So to further analyze which bugs were found by syzbot, I've looked through all
patches in drivers/video which were tagged with syzbot or syzkaller back to
year 2005. The vast majority fixed the reported issues on a higher level, e.g.
when screen is to be resized, or when font size is to be changed. The few ones
which touched driver code fixed a real driver bug, e.g. by adding a check.
But NONE of those patches touched code of either the SCROLL_MOVE or the
SCROLL_REDRAW case.
That means, there was no real reason why SCROLL_MOVE had to be ripped-out and
just SCROLL_REDRAW had to be used instead. The only reason I can imagine so far
was that SCROLL_MOVE wasn't used by DRM and as such it was assumed that it
could go away. That argument completely missed the fact that SCROLL_MOVE is
still heavily used by fbdev (non-DRM) drivers.
Some people mention that using memcpy() instead of the hardware acceleration is
pretty much the same speed. But that's not true, at least not for older graphic
cards and machines where we see speed decreases by factor 10 and more and thus
this change leads to console responsiveness way worse than before.
That's why the original commit is to be reverted. By reverting we
reintroduce hardware-based scrolling acceleration and fix the
performance regression for fbdev drivers.
There isn't any impact on DRM when reverting those patches.
Signed-off-by: Helge Deller <deller@gmx.de>
Acked-by: Geert Uytterhoeven <geert@linux-m68k.org>
Acked-by: Sven Schnelle <svens@stackframe.org>
Cc: stable@vger.kernel.org # v5.16+
Signed-off-by: Helge Deller <deller@gmx.de>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: https://patchwork.freedesktop.org/patch/msgid/20220202135531.92183-2-deller@gmx.de
|
|
If the parent GPIO controller is a sleeping controller (e.g. a GPIO
controller connected to I2C), getting or setting a GPIO triggers a
might_sleep() warning. This happens because the GPIO Aggregator takes
the can_sleep flag into account only for its internal locking, not for
calling into the parent GPIO controller.
Fix this by using the gpiod_[gs]et*_cansleep() APIs when calling into a
sleeping GPIO controller.
Reported-by: Mikko Salomäki <ms@datarespons.se>
Fixes: 828546e24280f721 ("gpio: Add GPIO Aggregator")
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: Bartosz Golaszewski <brgl@bgdev.pl>
|
|
The thead,c900-plic has been used in opensbi to distinguish
PLIC [1]. Although PLICs have the same behaviors in Linux,
they are different hardware with some custom initializing in
firmware(opensbi).
Qute opensbi patch commit-msg by Samuel:
The T-HEAD PLIC implementation requires setting a delegation bit
to allow access from S-mode. Now that the T-HEAD PLIC has its own
compatible string, set this bit automatically from the PLIC driver,
instead of reaching into the PLIC's MMIO space from another driver.
[1]: https://github.com/riscv-software-src/opensbi/commit/78c2b19218bd62653b9fb31623a42ced45f38ea6
Signed-off-by: Guo Ren <guoren@linux.alibaba.com>
Cc: Anup Patel <anup@brainfault.org>
Cc: Marc Zyngier <maz@kernel.org>
Cc: Palmer Dabbelt <palmer@dabbelt.com>
Cc: Samuel Holland <samuel@sholland.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Tested-by: Samuel Holland <samuel@sholland.org>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Link: https://lore.kernel.org/r/20220130135634.1213301-3-guoren@kernel.org
|
|
We have some systems out there that have both LPI support and an
ITS, but that don't expose the ITS in their firmware tables
(either because it is broken or because they run under a hypervisor
that hides it...).
Is such a configuration, we still register the HP notifier to free
the allocated tables if needed, resulting in a warning as there is
no memory to free (nothing was allocated the first place).
Fix it by keying the HP notifier on the presence of at least one
sucessfully probed ITS.
Fixes: d23bc2bc1d63 ("irqchip/gic-v3-its: Postpone LPI pending table freeing and memreserve")
Reported-by: Steev Klimaszewski <steev@kali.org>
Tested-by: Steev Klimaszewski <steev@kali.org>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Cc: Valentin Schneider <valentin.schneider@arm.com>
Link: https://lore.kernel.org/r/20220202103454.2480465-1-maz@kernel.org
|
|
While nvme_rdma_submit_async_event_work is checking the ctrl and queue
state before preparing the AER command and scheduling io_work, in order
to fully prevent a race where this check is not reliable the error
recovery work must flush async_event_work before continuing to destroy
the admin queue after setting the ctrl state to RESETTING such that
there is no race .submit_async_event and the error recovery handler
itself changing the ctrl state.
Signed-off-by: Sagi Grimberg <sagi@grimberg.me>
|
|
While nvme_tcp_submit_async_event_work is checking the ctrl and queue
state before preparing the AER command and scheduling io_work, in order
to fully prevent a race where this check is not reliable the error
recovery work must flush async_event_work before continuing to destroy
the admin queue after setting the ctrl state to RESETTING such that
there is no race .submit_async_event and the error recovery handler
itself changing the ctrl state.
Tested-by: Chris Leech <cleech@redhat.com>
Signed-off-by: Sagi Grimberg <sagi@grimberg.me>
|
|
Unlike .queue_rq, in .submit_async_event drivers may not check the ctrl
readiness for AER submission. This may lead to a use-after-free
condition that was observed with nvme-tcp.
The race condition may happen in the following scenario:
1. driver executes its reset_ctrl_work
2. -> nvme_stop_ctrl - flushes ctrl async_event_work
3. ctrl sends AEN which is received by the host, which in turn
schedules AEN handling
4. teardown admin queue (which releases the queue socket)
5. AEN processed, submits another AER, calling the driver to submit
6. driver attempts to send the cmd
==> use-after-free
In order to fix that, add ctrl state check to validate the ctrl
is actually able to accept the AER submission.
This addresses the above race in controller resets because the driver
during teardown should:
1. change ctrl state to RESETTING
2. flush async_event_work (as well as other async work elements)
So after 1,2, any other AER command will find the
ctrl state to be RESETTING and bail out without submitting the AER.
Signed-off-by: Sagi Grimberg <sagi@grimberg.me>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tnguy/net-queue
Tony Nguyen says:
====================
Intel Wired LAN Driver Updates 2022-02-01
This series contains updates to e1000e driver only.
Sasha removes CSME handshake with TGL platform as this is not supported
and is causing hardware unit hangs to be reported.
* '1GbE' of git://git.kernel.org/pub/scm/linux/kernel/git/tnguy/net-queue:
e1000e: Handshake with CSME starts from ADL platforms
e1000e: Separate ADP board type from TGP
====================
Link: https://lore.kernel.org/r/20220201173754.580305-1-anthony.l.nguyen@intel.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
The D-PHY specification (v1.2) explicitly mentions that the T-CLK-PRE
parameter's unit is Unit Interval(UI) and the minimum value is 8. Also,
kernel doc of the 'clk_pre' member of struct phy_configure_opts_mipi_dphy
mentions that it should be in UI. However, the dphy core driver wrongly
sets 'clk_pre' to 8000, which seems to hint that it's in picoseconds.
So, let's fix the dphy core driver to correctly reflect the T-CLK-PRE
parameter's minimum value according to the D-PHY specification.
I'm assuming that all impacted custom drivers shall program values in
TxByteClkHS cycles into hardware for the T-CLK-PRE parameter. The D-PHY
specification mentions that the frequency of TxByteClkHS is exactly 1/8
the High-Speed(HS) bit rate(each HS bit consumes one UI). So, relevant
custom driver code is changed to program those values as
DIV_ROUND_UP(cfg->clk_pre, BITS_PER_BYTE), then.
Note that I've only tested the patch with RM67191 DSI panel on i.MX8mq EVK.
Help is needed to test with other i.MX8mq, Meson and Rockchip platforms,
as I don't have the hardwares.
Fixes: 2ed869990e14 ("phy: Add MIPI D-PHY configuration options")
Tested-by: Liu Ying <victor.liu@nxp.com> # RM67191 DSI panel on i.MX8mq EVK
Reviewed-by: Andrzej Hajda <andrzej.hajda@intel.com>
Reviewed-by: Neil Armstrong <narmstrong@baylibre.com> # for phy-meson-axg-mipi-dphy.c
Tested-by: Neil Armstrong <narmstrong@baylibre.com> # for phy-meson-axg-mipi-dphy.c
Tested-by: Guido Günther <agx@sigxcpu.org> # Librem 5 (imx8mq) with it's rather picky panel
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Liu Ying <victor.liu@nxp.com>
Link: https://lore.kernel.org/r/20220124024007.1465018-1-victor.liu@nxp.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
|
|
In preparation for FORTIFY_SOURCE performing compile-time and run-time
field bounds checking for memcpy(), memmove(), and memset(), avoid
intentionally writing across neighboring fields.
Use flexible arrays instead of zero-element arrays (which look like they
are always overflowing) and split the cross-field memcpy() into two halves
that can be appropriately bounds-checked by the compiler.
We were doing:
#define ETH_HLEN 14
#define VLAN_HLEN 4
...
#define MLX5E_XDP_MIN_INLINE (ETH_HLEN + VLAN_HLEN)
...
struct mlx5e_tx_wqe *wqe = mlx5_wq_cyc_get_wqe(wq, pi);
...
struct mlx5_wqe_eth_seg *eseg = &wqe->eth;
struct mlx5_wqe_data_seg *dseg = wqe->data;
...
memcpy(eseg->inline_hdr.start, xdptxd->data, MLX5E_XDP_MIN_INLINE);
target is wqe->eth.inline_hdr.start (which the compiler sees as being
2 bytes in size), but copying 18, intending to write across start
(really vlan_tci, 2 bytes). The remaining 16 bytes get written into
wqe->data[0], covering byte_count (4 bytes), lkey (4 bytes), and addr
(8 bytes).
struct mlx5e_tx_wqe {
struct mlx5_wqe_ctrl_seg ctrl; /* 0 16 */
struct mlx5_wqe_eth_seg eth; /* 16 16 */
struct mlx5_wqe_data_seg data[]; /* 32 0 */
/* size: 32, cachelines: 1, members: 3 */
/* last cacheline: 32 bytes */
};
struct mlx5_wqe_eth_seg {
u8 swp_outer_l4_offset; /* 0 1 */
u8 swp_outer_l3_offset; /* 1 1 */
u8 swp_inner_l4_offset; /* 2 1 */
u8 swp_inner_l3_offset; /* 3 1 */
u8 cs_flags; /* 4 1 */
u8 swp_flags; /* 5 1 */
__be16 mss; /* 6 2 */
__be32 flow_table_metadata; /* 8 4 */
union {
struct {
__be16 sz; /* 12 2 */
u8 start[2]; /* 14 2 */
} inline_hdr; /* 12 4 */
struct {
__be16 type; /* 12 2 */
__be16 vlan_tci; /* 14 2 */
} insert; /* 12 4 */
__be32 trailer; /* 12 4 */
}; /* 12 4 */
/* size: 16, cachelines: 1, members: 9 */
/* last cacheline: 16 bytes */
};
struct mlx5_wqe_data_seg {
__be32 byte_count; /* 0 4 */
__be32 lkey; /* 4 4 */
__be64 addr; /* 8 8 */
/* size: 16, cachelines: 1, members: 3 */
/* last cacheline: 16 bytes */
};
So, split the memcpy() so the compiler can reason about the buffer
sizes.
"pahole" shows no size nor member offset changes to struct mlx5e_tx_wqe
nor struct mlx5e_umr_wqe. "objdump -d" shows no meaningful object
code changes (i.e. only source line number induced differences and
optimizations).
Fixes: b5503b994ed5 ("net/mlx5e: XDP TX forwarding support")
Signed-off-by: Kees Cook <keescook@chromium.org>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
|
|
In preparation for FORTIFY_SOURCE performing compile-time and run-time
field bounds checking for memcpy(), memmove(), and memset(), avoid
intentionally writing across neighboring fields.
Use struct_group() in struct vlan_ethhdr around members h_dest and
h_source, so they can be referenced together. This will allow memcpy()
and sizeof() to more easily reason about sizes, improve readability,
and avoid future warnings about writing beyond the end of h_dest.
"pahole" shows no size nor member offset changes to struct vlan_ethhdr.
"objdump -d" shows no object code changes.
Fixes: 34802a42b352 ("net/mlx5e: Do not modify the TX SKB")
Signed-off-by: Kees Cook <keescook@chromium.org>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
|
|
Currently the driver adds implicit modify hdr action for
decap rules on tunnel devices if the port is an ovs port.
This is also done if the action is drop and makes the modify
hdr redundant and also the FW doesn't support it and will generate
a syndrome.
kernel: mlx5_core 0000:08:00.0: mlx5_cmd_check:777:(pid 102063): SET_FLOW_TABLE_ENTRY(0x936) op_mod(0x0) failed, status bad parameter(0x3), syndrome (0x8708c3)
Fix it by adding the implicit modify hdr only for fwd actions.
Fixes: b16eb3c81fe2 ("net/mlx5: Support internal port as decap route device")
Fixes: 077cdda764c7 ("net/mlx5e: TC, Fix memory leak with rules with internal port")
Signed-off-by: Roi Dayan <roid@nvidia.com>
Reviewed-by: Ariel Levkovich <lariel@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
|
|
IPsec Tunnel mode crypto offload software parser (SWP) setting in data
path currently always set the inner L4 offset regardless of the
encapsulated L4 header type and whether it exists in the first place,
this breaks non TCP/UDP traffic as such.
Set the SWP inner L4 offset only when the IPsec tunnel encapsulated L4
header protocol is TCP/UDP.
While at it fix inner ip protocol read for setting MLX5_ETH_WQE_SWP_INNER_L4_UDP
flag to address the case where the ip header protocol is IPv6.
Fixes: f1267798c980 ("net/mlx5: Fix checksum issue of VXLAN and IPsec crypto offload")
Signed-off-by: Raed Salem <raeds@nvidia.com>
Reviewed-by: Maor Dickman <maord@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
|
|
IPsec crypto offload always set the ethernet segment checksum flags with
the inner L4 header checksum flag enabled for encapsulated IPsec offloaded
packet regardless of the encapsulated L4 header type, and even if it
doesn't exists in the first place, this breaks non TCP/UDP traffic as
such.
Set the inner L4 checksum flag only when the encapsulated L4 header
protocol is TCP/UDP using software parser swp_inner_l4_offset field as
indication.
Fixes: 5cfb540ef27b ("net/mlx5e: Set IPsec WAs only in IP's non checksum partial case.")
Signed-off-by: Raed Salem <raeds@nvidia.com>
Reviewed-by: Maor Dickman <maord@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
|
|
The hardware spec defines max_average_bw == 0 as "unlimited bandwidth".
max_average_bw is calculated as `ceil / BYTES_IN_MBIT`, which can become
0 when ceil is small, leading to an undesired effect of having no
bandwidth limit.
This commit fixes it by rounding up small values of ceil to 1 Mbit/s.
Fixes: 214baf22870c ("net/mlx5e: Support HTB offload")
Signed-off-by: Maxim Mikityanskiy <maximmi@nvidia.com>
Reviewed-by: Tariq Toukan <tariqt@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
|
|
The variable modact is not initialized before used in command
modify header allocation which can cause command to fail.
Fix by initializing modact with zeros.
Addresses-Coverity: ("Uninitialized scalar variable")
Fixes: 8f1e0b97cc70 ("net/mlx5: E-Switch, Mark miss packets with new chain id mapping")
Signed-off-by: Maor Dickman <maord@nvidia.com>
Reviewed-by: Roi Dayan <roid@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
|
|
Current implementation of bond netevent handler only check if
the handled netdev is VF representor and it missing a check if
the VF representor is on the same phys device of the bond handling
the netevent.
Fix by adding the missing check and optimizing the check if
the netdev is VF representor so it will not access uninitialized
private data and crashes.
BUG: kernel NULL pointer dereference, address: 000000000000036c
PGD 0 P4D 0
Oops: 0000 [#1] SMP NOPTI
Workqueue: eth3bond0 bond_mii_monitor [bonding]
RIP: 0010:mlx5e_is_uplink_rep+0xc/0x50 [mlx5_core]
RSP: 0018:ffff88812d69fd60 EFLAGS: 00010282
RAX: 0000000000000000 RBX: ffff8881cf800000 RCX: 0000000000000000
RDX: ffff88812d69fe10 RSI: 000000000000001b RDI: ffff8881cf800880
RBP: ffff8881cf800000 R08: 00000445cabccf2b R09: 0000000000000008
R10: 0000000000000004 R11: 0000000000000008 R12: ffff88812d69fe10
R13: 00000000fffffffe R14: ffff88820c0f9000 R15: 0000000000000000
FS: 0000000000000000(0000) GS:ffff88846fb00000(0000) knlGS:0000000000000000
CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033
CR2: 000000000000036c CR3: 0000000103d80006 CR4: 0000000000370ea0
DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000
DR3: 0000000000000000 DR6: 00000000fffe0ff0 DR7: 0000000000000400
Call Trace:
mlx5e_eswitch_uplink_rep+0x31/0x40 [mlx5_core]
mlx5e_rep_is_lag_netdev+0x94/0xc0 [mlx5_core]
mlx5e_rep_esw_bond_netevent+0xeb/0x3d0 [mlx5_core]
raw_notifier_call_chain+0x41/0x60
call_netdevice_notifiers_info+0x34/0x80
netdev_lower_state_changed+0x4e/0xa0
bond_mii_monitor+0x56b/0x640 [bonding]
process_one_work+0x1b9/0x390
worker_thread+0x4d/0x3d0
? rescuer_thread+0x350/0x350
kthread+0x124/0x150
? set_kthread_struct+0x40/0x40
ret_from_fork+0x1f/0x30
Fixes: 7e51891a237f ("net/mlx5e: Use netdev events to set/del egress acl forward-to-vport rule")
Signed-off-by: Maor Dickman <maord@nvidia.com>
Reviewed-by: Roi Dayan <roid@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
|
|
In case the HW doesn't perform header-data split, it will write the whole
packet into the data buffer in the WQ, in this case the SHAMPO CQE handler
couldn't use the header entry to build the SKB, instead it should allocate
a new memory to build the SKB using the function:
mlx5e_skb_from_cqe_mpwrq_nonlinear.
Fixes: f97d5c2a453e ("net/mlx5e: Add handle SHAMPO cqe support")
Signed-off-by: Khalid Manaa <khalidm@nvidia.com>
Reviewed-by: Tariq Toukan <tariqt@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
|
|
The HW doesn't wrap the CQE.shampo.header_index field according to the
headers buffer size, instead it always increases it until reaching overflow
of u16 size.
Thus the mlx5e_handle_rx_cqe_mpwrq_shampo handler should mask the
CQE header_index field to find the actual header index in the headers buffer.
Fixes: f97d5c2a453e ("net/mlx5e: Add handle SHAMPO cqe support")
Signed-off-by: Khalid Manaa <khalidm@nvidia.com>
Reviewed-by: Tariq Toukan <tariqt@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
|
|
When changing mode to switchdev, rep bridge init registered to netdevice
notifier holds the devlink lock and then takes pernet_ops_rwsem.
At that time deleting a netns holds pernet_ops_rwsem and then takes
the devlink lock.
Example sequence is:
$ ip netns add foo
$ devlink dev eswitch set pci/0000:00:08.0 mode switchdev &
$ ip netns del foo
deleting netns trace:
[ 1185.365555] ? devlink_pernet_pre_exit+0x74/0x1c0
[ 1185.368331] ? mutex_lock_io_nested+0x13f0/0x13f0
[ 1185.370984] ? xt_find_table+0x40/0x100
[ 1185.373244] ? __mutex_lock+0x24a/0x15a0
[ 1185.375494] ? net_generic+0xa0/0x1c0
[ 1185.376844] ? wait_for_completion_io+0x280/0x280
[ 1185.377767] ? devlink_pernet_pre_exit+0x74/0x1c0
[ 1185.378686] devlink_pernet_pre_exit+0x74/0x1c0
[ 1185.379579] ? devlink_nl_cmd_get_dumpit+0x3a0/0x3a0
[ 1185.380557] ? xt_find_table+0xda/0x100
[ 1185.381367] cleanup_net+0x372/0x8e0
changing mode to switchdev trace:
[ 1185.411267] down_write+0x13a/0x150
[ 1185.412029] ? down_write_killable+0x180/0x180
[ 1185.413005] register_netdevice_notifier+0x1e/0x210
[ 1185.414000] mlx5e_rep_bridge_init+0x181/0x360 [mlx5_core]
[ 1185.415243] mlx5e_uplink_rep_enable+0x269/0x480 [mlx5_core]
[ 1185.416464] ? mlx5e_uplink_rep_disable+0x210/0x210 [mlx5_core]
[ 1185.417749] mlx5e_attach_netdev+0x232/0x400 [mlx5_core]
[ 1185.418906] mlx5e_netdev_attach_profile+0x15b/0x1e0 [mlx5_core]
[ 1185.420172] mlx5e_netdev_change_profile+0x15a/0x1d0 [mlx5_core]
[ 1185.421459] mlx5e_vport_rep_load+0x557/0x780 [mlx5_core]
[ 1185.422624] ? mlx5e_stats_grp_vport_rep_num_stats+0x10/0x10 [mlx5_core]
[ 1185.424006] mlx5_esw_offloads_rep_load+0xdb/0x190 [mlx5_core]
[ 1185.425277] esw_offloads_enable+0xd74/0x14a0 [mlx5_core]
Fix this by registering rep bridges for per net netdev notifier
instead of global one, which operats on the net namespace without holding
the pernet_ops_rwsem.
Fixes: 19e9bfa044f3 ("net/mlx5: Bridge, add offload infrastructure")
Signed-off-by: Roi Dayan <roid@nvidia.com>
Reviewed-by: Vlad Buslov <vladbu@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
|
|
Only prio 1 is supported for nic mode when there is no ignore flow level
support in firmware. But for switchdev mode, which supports fixed number
of statically pre-allocated prios, this restriction is not relevant so
it can be relaxed.
Fixes: d671e109bd85 ("net/mlx5: Fix tc max supported prio for nic mode")
Signed-off-by: Dima Chumak <dchumak@nvidia.com>
Reviewed-by: Roi Dayan <roid@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
|
|
Such rules are redundant but allowed and passed to the driver.
The driver does not support offloading such rules so return an error.
Fixes: 03a9d11e6eeb ("net/mlx5e: Add TC drop and mirred/redirect action parsing for SRIOV offloads")
Signed-off-by: Roi Dayan <roid@nvidia.com>
Reviewed-by: Oz Shlomo <ozsh@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
|
|
Substitute del_timer() with del_timer_sync() in fw reset polling
deactivation flow, in order to prevent a race condition which occurs
when del_timer() is called and timer is deactivated while another
process is handling the timer interrupt. A situation that led to
the following call trace:
RIP: 0010:run_timer_softirq+0x137/0x420
<IRQ>
recalibrate_cpu_khz+0x10/0x10
ktime_get+0x3e/0xa0
? sched_clock_cpu+0xb/0xc0
__do_softirq+0xf5/0x2ea
irq_exit_rcu+0xc1/0xf0
sysvec_apic_timer_interrupt+0x9e/0xc0
asm_sysvec_apic_timer_interrupt+0x12/0x20
</IRQ>
Fixes: 38b9f903f22b ("net/mlx5: Handle sync reset request event")
Signed-off-by: Maher Sanalla <msanalla@nvidia.com>
Reviewed-by: Moshe Shemesh <moshe@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
|
|
When querying the module EEPROM, there was a misusage of the 'offset'
variable vs the 'query.offset' field.
Fix that by always using 'offset' and assigning its value to
'query.offset' right before the mcia register read call.
While at it, the cross-pages read size adjustment was changed to be more
intuitive.
Fixes: e19b0a3474ab ("net/mlx5: Refactor module EEPROM query")
Reported-by: Wang Yugui <wangyugui@e16-tech.com>
Signed-off-by: Gal Pressman <gal@nvidia.com>
Reviewed-by: Maxim Mikityanskiy <maximmi@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
|
|
This kind of action is not supported by firmware and generates a
syndrome.
kernel: mlx5_core 0000:08:00.0: mlx5_cmd_check:777:(pid 102063): SET_FLOW_TABLE_ENTRY(0x936) op_mod(0x0) failed, status bad parameter(0x3), syndrome (0x8708c3)
Fixes: d7e75a325cb2 ("net/mlx5e: Add offloading of E-Switch TC pedit (header re-write) actions")
Signed-off-by: Roi Dayan <roid@nvidia.com>
Reviewed-by: Oz Shlomo <ozsh@nvidia.com>
Reviewed-by: Maor Dickman <maord@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
|
|
Even though net_device->name is guaranteed to be null-terminated string of
size<=IFNAMSIZ, the test robot complains that return value of netdev_name()
can be larger:
In file included from include/trace/define_trace.h:102,
from drivers/net/ethernet/mellanox/mlx5/core/esw/diag/bridge_tracepoint.h:113,
from drivers/net/ethernet/mellanox/mlx5/core/esw/bridge.c:12:
drivers/net/ethernet/mellanox/mlx5/core/esw/diag/bridge_tracepoint.h: In function 'trace_event_raw_event_mlx5_esw_bridge_fdb_template':
>> drivers/net/ethernet/mellanox/mlx5/core/esw/diag/bridge_tracepoint.h:24:29: warning: 'strncpy' output may be truncated copying 16 bytes from a string of length 20 [-Wstringop-truncation]
24 | strncpy(__entry->dev_name,
| ^~~~~~~~~~~~~~~~~~~~~~~~~~
25 | netdev_name(fdb->dev),
| ~~~~~~~~~~~~~~~~~~~~~~
26 | IFNAMSIZ);
| ~~~~~~~~~
This is caused by the fact that default value of IFNAMSIZ is 16, while
placeholder value that is returned by netdev_name() for unnamed net devices
is larger than that.
The offending code is in a tracing function that is only called for mlx5
representors, so there is no straightforward way to reproduce the issue but
let's fix it for correctness sake by replacing strncpy() with strscpy() to
ensure that resulting string is always null-terminated.
Fixes: 9724fd5d9c2a ("net/mlx5: Bridge, add tracepoints")
Reported-by: kernel test robot <lkp@intel.com>
Signed-off-by: Vlad Buslov <vladbu@nvidia.com>
Reviewed-by: Roi Dayan <roid@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
|
|
The mlx5_esw_bridge_cleanup() is expected to be called with rtnl lock
taken, which is true for mlx5e_rep_bridge_cleanup() function but not for
error handling code in mlx5e_rep_bridge_init(). Add missing rtnl
lock/unlock calls and extend both mlx5_esw_bridge_cleanup() and its dual
function mlx5_esw_bridge_init() with ASSERT_RTNL() to verify the invariant
from now on.
Fixes: 7cd6a54a8285 ("net/mlx5: Bridge, handle FDB events")
Fixes: 19e9bfa044f3 ("net/mlx5: Bridge, add offload infrastructure")
Signed-off-by: Vlad Buslov <vladbu@nvidia.com>
Reviewed-by: Roi Dayan <roid@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tnguy/net-queue
Tony Nguyen says:
====================
Intel Wired LAN Driver Updates 2022-01-31
This series contains updates to i40e driver only.
Jedrzej fixes a condition check which would cause an error when
resetting bandwidth when DCB is active with one TC.
Karen resolves a null pointer dereference that could occur when removing
the driver while VSI rings are being disabled.
* '40GbE' of git://git.kernel.org/pub/scm/linux/kernel/git/tnguy/net-queue:
i40e: Fix reset path while removing the driver
i40e: Fix reset bw limit when DCB enabled with 1 TC
====================
Link: https://lore.kernel.org/r/20220201000522.505909-1-anthony.l.nguyen@intel.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
When setting Tx sci explicit, the Rx side is expected to use this
sci and not recalculate it from the packet.However, in case of Tx sci
is explicit and send_sci is off, the receiver is wrongly recalculate
the sci from the source MAC address which most likely be different
than the explicit sci.
Fix by preventing such configuration when macsec newlink is established
and return EINVAL error code on such cases.
Fixes: c09440f7dcb3 ("macsec: introduce IEEE 802.1AE driver")
Signed-off-by: Lior Nahmanson <liorna@nvidia.com>
Reviewed-by: Raed Salem <raeds@nvidia.com>
Signed-off-by: Raed Salem <raeds@nvidia.com>
Link: https://lore.kernel.org/r/1643542672-29403-1-git-send-email-raeds@nvidia.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
When rx_buf is allocated we need to account for IPHETH_IP_ALIGN,
which reduces the usable size by 2 bytes. Otherwise we have 1512
bytes usable instead of 1514, and if we receive more than 1512
bytes, ipheth_rcvbulk_callback is called with status -EOVERFLOW,
after which the driver malfunctiones and all communication stops.
Resolves ipheth 2-1:4.2: ipheth_rcvbulk_callback: urb status: -75
Fixes: f33d9e2b48a3 ("usbnet: ipheth: fix connectivity with iOS 14")
Signed-off-by: Georgi Valkov <gvalkov@abv.bg>
Tested-by: Jan Kiszka <jan.kiszka@siemens.com>
Link: https://lore.kernel.org/all/B60B8A4B-92A0-49B3-805D-809A2433B46C@abv.bg/
Link: https://lore.kernel.org/all/24851bd2769434a5fc24730dce8e8a984c5a4505.1643699778.git.jan.kiszka@siemens.com/
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Build bot produced a smatch indentation warning,
the code looks correct but it mixes spaces and tabs.
Reported-by: kernel test robot <lkp@intel.com>
Link: https://lore.kernel.org/r/20220131211730.3940875-1-kuba@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/broonie/spi
Pull spi fixes from Mark Brown:
"There are quite a few fixes that have accumilated since the merge
window here, all driver specific and none super urgent, plus a new
device ID for the Rockchip driver"
* tag 'spi-fix-v5.17-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/spi:
spi: mediatek: Avoid NULL pointer crash in interrupt
spi: dt-bindings: Fix 'reg' child node schema
spi: bcm-qspi: check for valid cs before applying chip select
spi: uniphier: fix reference count leak in uniphier_spi_probe()
spi: meson-spicc: add IRQ check in meson_spicc_probe
spi: uniphier: Fix a bug that doesn't point to private data correctly
spi: change clk_disable_unprepare to clk_unprepare
spi: spi-rockchip: Add rk3568-spi compatible
spi: stm32: make SPI_MASTER_MUST_TX flags only specific to STM32F4
spi: stm32: remove inexistant variables in struct stm32_spi_cfg comment
spi: stm32-qspi: Update spi registering
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/broonie/regulator
Pull regulator fixes from Mark Brown:
"A couple of very minor fixes for the regulator framework, nothing at
all urgent here"
* tag 'regulator-fix-v5.17-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/regulator:
regulator: MAX20086: add gpio/consumer.h
regulator: max20086: fix error code in max20086_parse_regulators_dt()
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/pdx86/platform-drivers-x86
Pull x86 platform driver fixes from Hans de Goede:
"This consists of various build- and bug-fixes as well as a few
hardware-id additions.
Highlights:
- Bunch of fixes for the new x86-android-tablets module
- Misc other fixes
- A couple of hw-id additions"
* tag 'platform-drivers-x86-v5.17-2' of git://git.kernel.org/pub/scm/linux/kernel/git/pdx86/platform-drivers-x86:
platform/x86: thinkpad_acpi: Fix incorrect use of platform profile on AMD platforms
platform/x86: amd-pmc: Correct usage of SMU version
platform/x86: asus-tf103c-dock: Make 2 global structs static
platform/x86: amd-pmc: Make amd_pmc_stb_debugfs_fops static
platform/x86: ISST: Fix possible circular locking dependency detected
platform/x86: intel_crystal_cove_charger: Fix IRQ masking / unmasking
platform/x86: thinkpad_acpi: Add quirk for ThinkPads without a fan
platform/x86: touchscreen_dmi: Add info for the RWC NANOTE P8 AY07J 2-in-1
platform/surface: Reinstate platform dependency
platform/x86: x86-android-tablets: Trivial typo fix for MODULE_AUTHOR
platform/x86: x86-android-tablets: Fix the buttons on CZC P10T tablet
platform/x86: x86-android-tablets: Constify the gpiod_lookup_tables arrays
platform/x86: x86-android-tablets: Add an init() callback to struct x86_dev_info
platform/x86: x86-android-tablets: Add support for disabling ACPI _AEI handlers
platform/x86: x86-android-tablets: Correct crystal_cove_charger module name
|
|
Christian reported a NULL pointer dereference in j721e_pcie_probe() caused
by 19e863828acf ("PCI: j721e: Drop redundant struct device *"), which
removed struct j721e_pcie.dev since there's another copy in struct
cdns_pcie.dev reachable via j721e_pcie->cdns_pcie->dev.
The problem is that j721e_pcie->cdns_pcie was dereferenced before being
initialized:
j721e_pcie_probe
pcie = devm_kzalloc() # struct j721e_pcie
j721e_pcie_ctrl_init(pcie)
dev = pcie->cdns_pcie->dev <-- dereference cdns_pcie
switch (mode) {
case PCI_MODE_RC:
cdns_pcie = ... # alloc as part of pci_host_bridge
pcie->cdns_pcie = cdns_pcie <-- initialize pcie->cdns_pcie
Move the cdns_pcie initialization earlier so it is done before it is used.
This also simplifies the error exits.
Fixes: 19e863828acf ("PCI: j721e: Drop redundant struct device *")
Link: https://lore.kernel.org/r/20220127222951.GA144828@bhelgaas
Link: https://lore.kernel.org/r/20220124122132.435743-1-christian.gmeiner@gmail.com
Reported-by: Christian Gmeiner <christian.gmeiner@gmail.com>
Tested-by: Christian Gmeiner <christian.gmeiner@gmail.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
|
|
Handshake with CSME/AMT on none provisioned platforms during S0ix flow
is not supported on TGL platform and can cause to HW unit hang. Update
the handshake with CSME flow to start from the ADL platform.
Fixes: 3e55d231716e ("e1000e: Add handshake with the CSME to support S0ix")
Signed-off-by: Sasha Neftin <sasha.neftin@intel.com>
Tested-by: Nechama Kraus <nechamax.kraus@linux.intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
|
|
We have the same LAN controller on different PCH's. Separate ADP board
type from a TGP which will allow for specific fixes to be applied for
ADP platforms.
Suggested-by: Kai-Heng Feng <kai.heng.feng@canonical.com>
Suggested-by: Dima Ruinskiy <dima.ruinskiy@intel.com>
Signed-off-by: Sasha Neftin <sasha.neftin@intel.com>
Tested-by: Nechama Kraus <nechamax.kraus@linux.intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
|
