summaryrefslogtreecommitdiff
path: root/drivers
AgeCommit message (Collapse)Author
2014-10-23rtl8192cu: Prevent Ooops under rtl92c_set_fw_rsvdpagepktKarsten Wiese
rtl92c_set_fw_rsvdpagepkt is used by rtl8192cu and its pci sibling rtl8192ce. rtl_cmd_send_packet crashes when called inside rtl8192cu because it works on memory allocated only by rtl8192ce. Fix the crash by calling a dummy function when used in rtl8192cu. Comparision with the realtek vendor driver makes me think, something is missing in the dummy function. Short test as WPA2 station show good results connected to an 802.11g basestation. Traffic stops after few MBytes as WPA2 station connected to an 802.11n basestation. Signed-off-by: Karsten Wiese <fzuuzf@googlemail.com> Acked-by: Larry Finger <Larry.Finger@lwfinger.net> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2014-10-23rtl8192cu: Call ieee80211_register_hw from rtl_usb_probeKarsten Wiese
In a previous patch the call to ieee80211_register_hw was moved from the load firmware callback to the rtl_pci_probe only. rt8192cu also uses this callback. Currently it doesnt create a wlan%d device. Fill in the call to ieee80211_register_hw in rtl_usb_probe. Signed-off-by: Karsten Wiese <fzuuzf@googlemail.com> Acked-by: Larry Finger <Larry.Finger@lwfinger.net> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2014-10-23rtl8192cu: Fix for rtlwifi's bluetooth coexist functionalityKarsten Wiese
Initialize function pointer with a function indicating bt coexist is not there. Prevents Ooops. Signed-off-by: Karsten Wiese <fzuuzf@googlemail.com> Acked-by: Larry Finger <Larry.Finger@lwfinger.net> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2014-10-23ath: use CTL region from cfg80211 if unset in EEPROMFelix Fietkau
Many AP devices do not have the proper regulatory domain programmed in EEPROM. Instead they expect the software to set the appropriate region. For these devices, the country code defaults to US, and the driver uses the US CTL tables as well. On devices bought in Europe this can lead to tx power being set too high on the band edges, even if the cfg80211 regdomain is set correctly. Fix this issue by taking into account the DFS region, but only when the EEPROM regdomain is set to default. Signed-off-by: Felix Fietkau <nbd@openwrt.org> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2014-10-23rtlwifi: rtl8821ae: Fix possible array overrunLarry Finger
The kbuild test robot reported a possible array overrun. The affected code checks for overruns, but fails to take the steps necessary to fix them. Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2014-10-23ath9k: Enable HW queue control only for MCCSujith Manoharan
Enabling HW queue control for normal (non-mcc) mode causes problems with queue management, resulting in traffic stall. Since it is mainly required for fairness in MCC mode, disable it for the general case. Bug: https://dev.openwrt.org/ticket/18164 Cc: Felix Fietkau <nbd@openwrt.org> Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2014-10-23rtlwifi: prevent format string usage from leakingKees Cook
Use "%s" in the workqueue allocation to make sure the rtl_hal_cfg name can never accidentally leak information via a format string. Signed-off-by: Kees Cook <keescook@chromium.org> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2014-10-23bcma: add another PCI ID of device with BCM43228Rafał Miłecki
It was found attached to the BCM47081A0 SoC. Log: bcma: bus0: Found chip with id 43228, rev 0x00 and package 0x08 Signed-off-by: Rafał Miłecki <zajec5@gmail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2014-10-23brcmfmac: dhd_sdio.c: Cleaning up missing null-terminate in conjunction with ↵Rickard Strandqvist
strncpy Replacing strncpy with strlcpy to avoid strings that lacks null terminate. And changed from using strncat to strlcat to simplify code. Signed-off-by: Rickard Strandqvist <rickard_strandqvist@spectrumdigital.se> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2014-10-23rtlwifi: rtl8192ee: Prevent log spamming for switch statementsLarry Finger
The driver logs a message when the default branch of switch statements are taken. Such information is useful when debugging, but these log items should not be seen for standard usage. Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2014-10-23bcma: fix build when CONFIG_OF_ADDRESS is not setHauke Mehrtens
Commit 2101e533f41a ("bcma: register bcma as device tree driver") introduces a hard dependency on OF_ADDRESS into the bcma driver. OF_ADDRESS is specifically disabled for the sparc architecture. This results in the following error when building sparc64:allmodconfig. drivers/bcma/main.c: In function 'bcma_of_find_child_device': drivers/bcma/main.c:150:3: error: implicit declaration of function 'of_translate_address' Fixes: 2101e533f41a ("bcma: register bcma as device tree driver") Reported-by: Guenter Roeck <linux@roeck-us.net> Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de> Reviewed-by: Guenter Roeck <linux@roeck-us.net> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2014-10-23MIPS: Kconfig: Add missing MIPS_CPS dependencies to PM and cpuidleMarkos Chandras
The MIPS_CPS_PM and MIPS_CPS_CPUIDLE implementation should depend on the MIPS_CPS symbol to avoid the following build problem arch/mips/kernel/pm-cps.c: In function 'cps_pm_enter_state': arch/mips/kernel/pm-cps.c:164:26: error: 'cpu_coherent_mask' undeclared (first use in this function) cpumask_clear_cpu(cpu, &cpu_coherent_mask); ^ Signed-off-by: Markos Chandras <markos.chandras@imgtec.com> Cc: Paul Burton <paul.burton@imgtec.com> Cc: linux-mips@linux-mips.org Patchwork: http://patchwork.linux-mips.org/patch/7798/ Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
2014-10-23xen/pci: Allocate memory for physdev_pci_device_add's optarrBoris Ostrovsky
physdev_pci_device_add's optarr[] is a zero-sized array and therefore reference to add.optarr[0] is accessing memory that does not belong to the 'add' variable. Signed-off-by: Boris Ostrovsky <boris.ostrovsky@oracle.com> Reviewed-by: Jan Beulich <jbeulich@suse.com> Signed-off-by: David Vrabel <david.vrabel@citrix.com>
2014-10-23xen/balloon: Don't continue ballooning when BP_ECANCELED is encounteredBoris Ostrovsky
Commit 3dcf63677d4e ("xen/balloon: cancel ballooning if adding new memory failed") makes reserve_additional_memory() return BP_ECANCELED when an error is encountered. This error, however, is ignored by the caller (balloon_process()) since it is overwritten by subsequent call to update_schedule(). This results in continuous attempts to add more memory, all of which are likely to fail again. We should stop trying to schedule next iteration of ballooning when the current one has failed. Signed-off-by: Boris Ostrovsky <boris.ostrovsky@oracle.com> Reviewed-by: Daniel Kiper <daniel.kiper@oracle.com> Signed-off-by: David Vrabel <david.vrabel@citrix.com>
2014-10-23drm/cirrus: bind also to qemu-xen-traditionalOlaf Hering
qemu as used by xend/xm toolstack uses a different subvendor id. Bind the drm driver also to this emulated card. Signed-off-by: Olaf Hering <olaf@aepfle.de> cc: stable@vger.kernel.org Signed-off-by: Dave Airlie <airlied@redhat.com>
2014-10-22hyperv: Fix the total_data_buflen in send pathHaiyang Zhang
total_data_buflen is used by netvsc_send() to decide if a packet can be put into send buffer. It should also include the size of RNDIS message before the Ethernet frame. Otherwise, a messge with total size bigger than send_section_size may be copied into the send buffer, and cause data corruption. [Request to include this patch to the Stable branches] Signed-off-by: Haiyang Zhang <haiyangz@microsoft.com> Reviewed-by: K. Y. Srinivasan <kys@microsoft.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2014-10-22amd-xgbe: Fix napi Rx budget accountingLendacky, Thomas
Currently the amd-xgbe driver increments the packets processed counter each time a descriptor is processed. Since a packet can be represented by more than one descriptor incrementing the counter in this way is not appropriate. Also, since multiple descriptors cause the budget check to be short circuited, sometimes the returned value from the poll function would be larger than the budget value resulting in a WARN_ONCE being triggered. Update the polling logic to properly account for the number of packets processed and exit when the budget value is reached. Signed-off-by: Tom Lendacky <thomas.lendacky@amd.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2014-10-22amd-xgbe: Properly handle feature changes via ethtoolLendacky, Thomas
The ndo_set_features callback function was improperly using an unsigned int to save the current feature value for features such as NETIF_F_RXCSUM. Since that feature is in the upper 32 bits of a 64 bit variable the result was always 0 making it not possible to actually turn off the hardware RX checksum support. Change the unsigned int type to the netdev_features_t type in order to properly capture the current value and perform the proper operation. Signed-off-by: Tom Lendacky <thomas.lendacky@amd.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2014-10-22net: fec: ptp: fix NULL pointer dereference if ptp_clock is not setPhilipp Zabel
Since commit 278d24047891 (net: fec: ptp: Enable PPS output based on ptp clock) fec_enet_interrupt calls fec_ptp_check_pps_event unconditionally, which calls into ptp_clock_event. If fep->ptp_clock is NULL, ptp_clock_event tries to dereference the NULL pointer. Since on i.MX53 fep->bufdesc_ex is not set, fec_ptp_init is never called, and fep->ptp_clock is NULL, which reliably causes a kernel panic. This patch adds a check for fep->ptp_clock == NULL in fec_enet_interrupt. Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de> Signed-off-by: David S. Miller <davem@davemloft.net>
2014-10-22e7xxx_edac: Report CE events properlyJason Baron
Fix CE event being reported as HW_EVENT_ERR_UNCORRECTED. Signed-off-by: Jason Baron <jbaron@akamai.com> Cc: stable@vger.kernel.org Link: http://lkml.kernel.org/r/e6dd616f2cd51583a7e77af6f639b86313c74144.1413405053.git.jbaron@akamai.com Signed-off-by: Borislav Petkov <bp@suse.de>
2014-10-22cpc925_edac: Report UE events properlyJason Baron
Fix UE event being reported as HW_EVENT_ERR_CORRECTED. Signed-off-by: Jason Baron <jbaron@akamai.com> Cc: stable@vger.kernel.org Link: http://lkml.kernel.org/r/8beb13803500076fef827eab33d523e355d83759.1413405053.git.jbaron@akamai.com Signed-off-by: Borislav Petkov <bp@suse.de>
2014-10-22i82860_edac: Report CE events properlyJason Baron
Fix CE event being reported as HW_EVENT_ERR_UNCORRECTED. Signed-off-by: Jason Baron <jbaron@akamai.com> Cc: stable@vger.kernel.org Link: http://lkml.kernel.org/r/7aee8e244a32ff86b399a8f966c4aae70296aae0.1413405053.git.jbaron@akamai.com Signed-off-by: Borislav Petkov <bp@suse.de>
2014-10-22i3200_edac: Report CE events properlyJason Baron
Fix CE event being reported as HW_EVENT_ERR_UNCORRECTED. Signed-off-by: Jason Baron <jbaron@akamai.com> Cc: stable@vger.kernel.org Link: http://lkml.kernel.org/r/d02465b4f30314b390c12c061502eda5e9d29c52.1413405053.git.jbaron@akamai.com Signed-off-by: Borislav Petkov <bp@suse.de>
2014-10-22net: fs_enet: set back promiscuity mode after restartLEROY Christophe
After interface restart (eg: after link disconnection/reconnection), the bridge function doesn't work anymore. This is due to the promiscuous mode being cleared by the restart. The mac-fcc already includes code to set the promiscuous mode back during the restart. This patch adds the same handling to mac-fec and mac-scc. Tested with bridge function on MPC885 with FEC. Reported-by: Germain Montoies <germain.montoies@c-s.fr> Signed-off-by: Christophe Leroy <christophe.leroy@c-s.fr> Signed-off-by: David S. Miller <davem@davemloft.net>
2014-10-22sfc: remove incorrect EFX_BUG_ON_PARANOID checkJon Cooper
write_count and insert_count can wrap around, making > check invalid. Fixes: 70b33fb0ddec827cbbd14cdc664fc27b2ef4a6b6 ("sfc: add support for skb->xmit_more"). Signed-off-by: Edward Cree <ecree@solarflare.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2014-10-22null_blk: Cleanup error recovery in null_add_dev()Jan Kara
When creation of queues fails in init_driver_queues(), we free the queues. But null_add_dev() doesn't test for this failure and continues with the setup leading to strange consequences, likely oops. Fix the problem by testing whether init_driver_queues() failed and do proper error cleanup. Coverity-id: 1148005 Signed-off-by: Jan Kara <jack@suse.cz> Signed-off-by: Jens Axboe <axboe@fb.com>
2014-10-22spi: orion: fix potential NULL pointer de-referenceGreg Ungerer
It's possible that the call to of_match_device() (introduced in commit df59fa7f ["spi: orion: support armada extended baud rates"]) may return a NULL if there is no match in the device tree (or perhaps no device tree at all). Check the return pointer and set the local device data to the lowest common denominator orion device data if it is NULL. Reported-by: Karl Beldan <karl.beldan@gmail.com> Signed-off-by: Greg Ungerer <gerg@uclinux.org> Signed-off-by: Mark Brown <broonie@kernel.org>
2014-10-22OMAPDSS: DSI: Fix PLL_SELFEQDCO field widthTomi Valkeinen
PLL_SELFREQDCO bitfield is from bit 3 to 1, but the driver writes bits from 4 to 1. The bit 4 is 'reserved', so this probably should not cause any issues, but it's better to fix it. Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
2014-10-22OMAPDSS: fix dispc register dump for preload & mflagTomi Valkeinen
Preload register is dumped twice for video overlays and mflag register is not dumped for GFX. Fix the register dump. Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
2014-10-22OMAPDSS: DISPC: fix mflag offsetTomi Valkeinen
The register offset for DISPC_OVL_MFLAG_THRESHOLD is wrong, fix it. Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
2014-10-22OMAPDSS: HDMI: fix regsd writeTomi Valkeinen
HDMI PLL's REGSD field is only set by the driver if the PLL's output clock is over 1GHz. This is clearly an error, as REGSD should be set always. Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
2014-10-22power: reset: at91-reset: fix power down registerAlexandre Belloni
In the case of at91sam9g45_restart(), the driver is writing AT91_DDRSDRC_LPCB_POWER_DOWN to AT91_DDRSDRC_RTR, this should actually be AT91_DDRSDRC_LPR. Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com> Acked-by: Sebastian Reichel <sre@kernel.org> Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
2014-10-22OMAPDSS: HDMI: fix PLL GO bit handlingTomi Valkeinen
The PLL settings are committed by setting GO bit, which is then cleared by the HW when the settings have been taken into use. The current PLL code handles this wrong: instead of waiting for the bit to be cleared, it waits for the bit to be set. Usually, the bit is always set, as the CPU has just set it before. However, if the CPU takes enough time between setting the GO bit and checking it, the HW may already have cleared the bit and this leads to timeout error. Fix the wait to check the bit properly. Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
2014-10-22OMAPFB: fix releasing overlaysTomi Valkeinen
omapfb disables all the overlays when freeing resources, but it should also remove those overlays from overlay managers. Not doing so causes a crash if omapfb is unbound and bound, or omapfb module is removed and loaded, while keeping omapdss around. Fix this by calling unset_manager() for all overlays. Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
2014-10-22OMAPFB: fix overlay disable when freeing resources.Tomi Valkeinen
When omapfb is shutting down, it will disable all the overlays. However, instead of actually disabling all the overlays, it disables only all the overlays that are currently attached to framebuffers. On OMAP4+, this leaves the fourth overlay left enabled. Fix the loop so that we actually go through all the overlays. Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
2014-10-22OMAPDSS: apply: wait pending updates on manager disableTomi Valkeinen
We should wait for any pending updates when an overlay manager is about to be disabled, because the updates will never be finished if the manager is disabled too early. Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
2014-10-22OMAPFB: remove __exit annotationFelipe Balbi
If we leave __exit annotation, driver can't be unbound through sysfs. Signed-off-by: Felipe Balbi <balbi@ti.com> Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
2014-10-22OMAPDSS: set suppress_bind_attrsTomi Valkeinen
omapdss drivers cannot handle devices being unbound while the devices are part of a connected display pipeline. Module refcounts are used to prevent unloading the modules, but one can still manually unbind the devices via sysfs, causing crash. Set suppress_bind_attrs to disable the bind/unbind support via sysfs. Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
2014-10-22OMAPFB: add missing MODULE_ALIAS()Felipe Balbi
without MODULE_ALIAS(), omapfb won't get loaded automatically. Signed-off-by: Felipe Balbi <balbi@ti.com> Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
2014-10-22drivers: video: fbdev: atmel_lcdfb.c: remove unnecessary headerAlexandre Belloni
Remove unnecessary mach/cpu.h header to be able to converge to a multiplatform kernel. Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com> Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com> Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
2014-10-22video/console: Resolve several shadow warningsMark Rustad
Resolve shadow warnings that appear in W=2 builds by renaming the "state" global to "vgastate". Signed-off-by: Mark Rustad <mark.d.rustad@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
2014-10-22fbcon: Fix option parsing control flow in fb_console_setupMaarten ter Huurne
Since strsep is used to tokenize the options string, after each option match the code should use "continue" to get the next token from strsep. This patch applies this pattern consistently. Previously, for "scrollback:" and "map:" the parse code would return (unconditionally: strsep ensures *options != ','), causing any following option to be ignored, while for "vc:" the parse code would go on to parse further options within the same token, which could lead to invalid input being accepted. Signed-off-by: Maarten ter Huurne <maarten@treewalker.org> Acked-by: Paul Cercueil <paul@crapouillou.net> Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
2014-10-22qxl: don't create too large primary surfaceMarc-André Lureau
Limit primary to qemu vgamem size, to avoid reaching qemu guest bug "requested primary larger than framebuffer" on resizing screen too large to fit. Remove unneeded and misleading variables. Related to: https://bugzilla.redhat.com/show_bug.cgi?id=1127552 Signed-off-by: Marc-André Lureau <marcandre.lureau@redhat.com> Cc: stable@vger.kernel.org Signed-off-by: Dave Airlie <airlied@redhat.com>
2014-10-21ACPI / platform: provide default DMA maskHeikki Krogerus
Most devices are configured for 32-bit DMA addresses. Setting the mask to 32-bit here removes the need for the drivers to do it separately. Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com> Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
2014-10-21Merge branch 'for-next' of ↵Linus Torvalds
git://git.kernel.org/pub/scm/linux/kernel/git/nab/target-pending Pull SCSI target updates from Nicholas Bellinger: "Here are the target updates for v3.18-rc2 code. These where originally destined for -rc1, but due to the combination of travel last week for KVM Forum and my mistake of taking the three week merge window literally, the pull request slipped.. Apologies for that. Things where reasonably quiet this round. The highlights include: - New userspace backend driver (target_core_user.ko) by Shaohua Li and Andy Grover - A number of cleanups in target, iscsi-taret and qla_target code from Joern Engel - Fix an OOPs related to queue full handling with CHECK_CONDITION status from Quinn Tran - Fix to disable TX completion interrupt coalescing in iser-target, that was causing problems on some hardware - Fix for PR APTPL metadata handling with demo-mode ACLs I'm most excited about the new backend driver that uses UIO + shared memory ring to dispatch I/O and control commands into user-space. This was probably the most requested feature by users over the last couple of years, and opens up a new area of development + porting of existing user-space storage applications to LIO. Thanks to Shaohua + Andy for making this happen. Also another honorable mention, a new Xen PV SCSI driver was merged via the xen/tip.git tree recently, which puts us now at 10 target drivers in upstream! Thanks to David Vrabel + Juergen Gross for their work to get this code merged" * 'for-next' of git://git.kernel.org/pub/scm/linux/kernel/git/nab/target-pending: (40 commits) target/file: fix inclusive vfs_fsync_range() end iser-target: Disable TX completion interrupt coalescing target: Add force_pr_aptpl device attribute target: Fix APTPL metadata handling for dynamic MappedLUNs qla_target: don't delete changed nacls target/user: Recalculate pad size inside is_ring_space_avail() tcm_loop: Fixup tag handling iser-target: Fix smatch warning target/user: Fix up smatch warnings in tcmu_netlink_event target: Add a user-passthrough backstore target: Add documentation on the target userspace pass-through driver uio: Export definition of struct uio_device target: Remove unneeded check in sbc_parse_cdb target: Fix queue full status NULL pointer for SCF_TRANSPORT_TASK_SENSE qla_target: rearrange struct qla_tgt_prm qla_target: improve qlt_unmap_sg() qla_target: make some global functions static qla_target: remove unused parameter target: simplify core_tmr_abort_task target: encapsulate smp_mb__after_atomic() ...
2014-10-21Merge branch 'for-linus' of git://git.open-osd.org/linux-open-osdLinus Torvalds
Pull email address change from Boaz Harrosh. * 'for-linus' of git://git.open-osd.org/linux-open-osd: Boaz Harrosh - fix email in Documentation Boaz Harrosh - Fix broken email address MAINTAINERS: Change Boaz Harrosh's email
2014-10-21enic: Do not call napi_disable when preemption is disabled.Govindarajulu Varadarajan
In enic_stop, we disable preemption using local_bh_disable(). We disable preemption to wait for busy_poll to finish. napi_disable should not be called here as it might sleep. Moving napi_disable() call out side of local_bh_disable. BUG: sleeping function called from invalid context at include/linux/netdevice.h:477 in_atomic(): 1, irqs_disabled(): 0, pid: 443, name: ifconfig INFO: lockdep is turned off. Preemption disabled at:[<ffffffffa029c5c4>] enic_rfs_flw_tbl_free+0x34/0xd0 [enic] CPU: 31 PID: 443 Comm: ifconfig Not tainted 3.17.0-netnext-05504-g59f35b8 #268 Hardware name: Bochs Bochs, BIOS Bochs 01/01/2011 ffff8800dac10000 ffff88020b8dfcb8 ffffffff8148a57c 0000000000000000 ffff88020b8dfcd0 ffffffff8107e253 ffff8800dac12a40 ffff88020b8dfd10 ffffffffa029305b ffff88020b8dfd48 ffff8800dac10000 ffff88020b8dfd48 Call Trace: [<ffffffff8148a57c>] dump_stack+0x4e/0x7a [<ffffffff8107e253>] __might_sleep+0x123/0x1a0 [<ffffffffa029305b>] enic_stop+0xdb/0x4d0 [enic] [<ffffffff8138ed7d>] __dev_close_many+0x9d/0xf0 [<ffffffff8138ef81>] __dev_close+0x31/0x50 [<ffffffff813974a8>] __dev_change_flags+0x98/0x160 [<ffffffff81397594>] dev_change_flags+0x24/0x60 [<ffffffff814085fd>] devinet_ioctl+0x63d/0x710 [<ffffffff81139c16>] ? might_fault+0x56/0xc0 [<ffffffff81409ef5>] inet_ioctl+0x65/0x90 [<ffffffff813768e0>] sock_do_ioctl+0x20/0x50 [<ffffffff81376ebb>] sock_ioctl+0x20b/0x2e0 [<ffffffff81197250>] do_vfs_ioctl+0x2e0/0x500 [<ffffffff81492619>] ? sysret_check+0x22/0x5d [<ffffffff81285f23>] ? __this_cpu_preempt_check+0x13/0x20 [<ffffffff8109fe19>] ? trace_hardirqs_on_caller+0x119/0x270 [<ffffffff811974ac>] SyS_ioctl+0x3c/0x80 [<ffffffff814925ed>] system_call_fastpath+0x1a/0x1f Signed-off-by: Govindarajulu Varadarajan <_govind@gmx.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2014-10-21enic: fix possible deadlock in enic_stop/ enic_rfs_flw_tbl_freeGovindarajulu Varadarajan
The following warning is shown when spinlock debug is enabled. This occurs when enic_flow_may_expire timer function is running and enic_stop is called on same CPU. Fix this by using spink_lock_bh(). ================================= [ INFO: inconsistent lock state ] 3.17.0-netnext-05504-g59f35b8 #268 Not tainted --------------------------------- inconsistent {IN-SOFTIRQ-W} -> {SOFTIRQ-ON-W} usage. ifconfig/443 [HC0[0]:SC0[0]:HE1:SE1] takes: (&(&enic->rfs_h.lock)->rlock){+.?...}, at: enic_rfs_flw_tbl_free+0x34/0xd0 [enic] {IN-SOFTIRQ-W} state was registered at: [<ffffffff810a25af>] __lock_acquire+0x83f/0x21c0 [<ffffffff810a45f2>] lock_acquire+0xa2/0xd0 [<ffffffff814913fc>] _raw_spin_lock+0x3c/0x80 [<ffffffffa029c3d5>] enic_flow_may_expire+0x25/0x130[enic] [<ffffffff810bcd07>] call_timer_fn+0x77/0x100 [<ffffffff810bd8e3>] run_timer_softirq+0x1e3/0x270 [<ffffffff8105f9ae>] __do_softirq+0x14e/0x280 [<ffffffff8105fdae>] irq_exit+0x8e/0xb0 [<ffffffff8103da0f>] smp_apic_timer_interrupt+0x3f/0x50 [<ffffffff81493742>] apic_timer_interrupt+0x72/0x80 [<ffffffff81018143>] default_idle+0x13/0x20 [<ffffffff81018a6a>] arch_cpu_idle+0xa/0x10 [<ffffffff81097676>] cpu_startup_entry+0x2c6/0x330 [<ffffffff8103b7ad>] start_secondary+0x21d/0x290 irq event stamp: 2997 hardirqs last enabled at (2997): [<ffffffff81491865>] _raw_spin_unlock_irqrestore+0x65/0x90 hardirqs last disabled at (2996): [<ffffffff814915e6>] _raw_spin_lock_irqsave+0x26/0x90 softirqs last enabled at (2968): [<ffffffff813b57a3>] dev_deactivate_many+0x213/0x260 softirqs last disabled at (2966): [<ffffffff813b5783>] dev_deactivate_many+0x1f3/0x260 other info that might help us debug this: Possible unsafe locking scenario: CPU0 ---- lock(&(&enic->rfs_h.lock)->rlock); <Interrupt> lock(&(&enic->rfs_h.lock)->rlock); *** DEADLOCK *** Reported-by: Jan Stancek <jstancek@redhat.com> Signed-off-by: Govindarajulu Varadarajan <_govind@gmx.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2014-10-21Merge branch 'mailbox-for-linus' of ↵Linus Torvalds
git://git.linaro.org/landing-teams/working/fujitsu/integration Pull mailbox framework from Jassi Brar: "A framework for Mailbox controllers and clients have been cooking for more than a year now. Everybody in the CC list had been copied on patchset revisions and most of them have made sounds of approval, though just one concrete Reviewed-by. The patchset has also been in linux-next for a couple of weeks now and no conflict has been reported. The framework has the backing of at least 5 platforms, though I can't say if/when they upstream their drivers (some businesses have 'changed')" (Further acked-by by Arnd Bergmann and Suman Anna in the pull request thread) * 'mailbox-for-linus' of git://git.linaro.org/landing-teams/working/fujitsu/integration: dt: mailbox: add generic bindings doc: add documentation for mailbox framework mailbox: Introduce framework for mailbox mailbox: rename pl320-ipc specific mailbox.h
2014-10-21Merge git://www.linux-watchdog.org/linux-watchdogLinus Torvalds
Pull watchdog updates from Wim Van Sebroeck: - new Cadence WDT driver - new Ricoh RN5T618 watchdog - new DA9063 PMIC watchdog driver - new Meson WDT driver - add restart handling code - fixes and improvements * git://www.linux-watchdog.org/linux-watchdog: (25 commits) watchdog: meson: remove magic value for reboot watchdog: Let XILINX_WATCHDOG and TEGRA_WATCHDOG depend on HAS_IOMEM watchdog: sunxi: Add A31 watchdog support watchdog: sunxi: support parameterized compatible strings watchdog: imx2_wdt: add restart handler support watchdog: qcom: register a restart notifier watchdog: s3c2410: add restart handler watchdog: dw_wdt: add restart handler support ARM: defconfig: update multi_v7_defconfig ARM: meson: add watchdog driver ARM: docs: add documentation binding for meson watchdog stmp3xxx_rtc_wdt: Add suspend/resume PM support watchdog: Add DA9063 PMIC watchdog driver. watchdog: add driver for Ricoh RN5T618 watchdog watchdog: s3c2410_wdt: Add support for Watchdog device on Exynos7 watchdog: qcom: document device tree bindings watchdog: qcom: add support for KPSS WDT watchdog: dw_wdt: initialise TOP_INIT in dw_wdt_set_top() devicetree: Add Cadence WDT devicetree bindings documentation watchdog: Add Cadence WDT driver ...
generated by cgit v1.2.3 (git 2.39.1) at 2025-08-05 14:52:28 +0000