| Age | Commit message (Collapse) | Author |
|---|
|
In response to a disk I/O request, Hyper-V has been observed to return SRB
status value 0x30. This indicates the request was not processed by Hyper-V
because low memory conditions on the host caused an internal error. The
0x30 status is not recognized by storvsc, so the I/O operation is not
flagged as an error. The request is treated as if it completed normally but
with zero data transferred, causing a flood of retries.
Add a definition for this SRB status value and handle it like other error
statuses from the Hyper-V host.
Signed-off-by: Michael Kelley <mikelley@microsoft.com>
Link: https://lore.kernel.org/r/1688788886-94279-1-git-send-email-mikelley@microsoft.com
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
Pull in the currently staged SCSI fixes for 6.5.
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
Generate a hotplug event after registering a client to allow the
client to configure its display. Remove the hotplug calls from the
existing clients for fbdev emulation. This change fixes a concurrency
bug between registering a client and receiving events from the DRM
core. The bug is present in the fbdev emulation of all drivers.
The fbdev emulation currently generates a hotplug event before
registering the client to the device. For each new output, the DRM
core sends an additional hotplug event to each registered client.
If the DRM core detects first output between sending the artificial
hotplug and registering the device, the output's hotplug event gets
lost. If this is the first output, the fbdev console display remains
dark. This has been observed with amdgpu and fbdev-generic.
Fix this by adding hotplug generation directly to the client's
register helper drm_client_register(). Registering the client and
receiving events are serialized by struct drm_device.clientlist_mutex.
So an output is either configured by the initial hotplug event, or
the client has already been registered.
The bug was originally added in commit 6e3f17ee73f7 ("drm/fb-helper:
generic: Call drm_client_add() after setup is done"), in which adding
a client and receiving a hotplug event switched order. It was hidden,
as most hardware and drivers have at least on static output configured.
Other drivers didn't use the internal DRM client or still had struct
drm_mode_config_funcs.output_poll_changed set. That callback handled
hotplug events as well. After not setting the callback in amdgpu in
commit 0e3172bac3f4 ("drm/amdgpu: Don't set struct
drm_driver.output_poll_changed"), amdgpu did not show a framebuffer
console if output events got lost. The bug got copy-pasted from
fbdev-generic into the other fbdev emulation.
Reported-by: Moritz Duge <MoritzDuge@kolahilft.de>
Closes: https://gitlab.freedesktop.org/drm/amd/-/issues/2649
Fixes: 6e3f17ee73f7 ("drm/fb-helper: generic: Call drm_client_add() after setup is done")
Fixes: 8ab59da26bc0 ("drm/fb-helper: Move generic fbdev emulation into separate source file")
Fixes: b79fe9abd58b ("drm/fbdev-dma: Implement fbdev emulation for GEM DMA helpers")
Fixes: 63c381552f69 ("drm/armada: Implement fbdev emulation as in-kernel client")
Fixes: 49953b70e7d3 ("drm/exynos: Implement fbdev emulation as in-kernel client")
Fixes: 8f1aaccb04b7 ("drm/gma500: Implement client-based fbdev emulation")
Fixes: 940b869c2f2f ("drm/msm: Implement fbdev emulation as in-kernel client")
Fixes: 9e69bcd88e45 ("drm/omapdrm: Implement fbdev emulation as in-kernel client")
Fixes: e317a69fe891 ("drm/radeon: Implement client-based fbdev emulation")
Fixes: 71ec16f45ef8 ("drm/tegra: Implement fbdev emulation as in-kernel client")
Fixes: 0e3172bac3f4 ("drm/amdgpu: Don't set struct drm_driver.output_poll_changed")
Signed-off-by: Thomas Zimmermann <tzimmermann@suse.de>
Tested-by: Moritz Duge <MoritzDuge@kolahilft.de>
Tested-by: Torsten Krah <krah.tm@gmail.com>
Tested-by: Paul Schyska <pschyska@gmail.com>
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Cc: David Airlie <airlied@gmail.com>
Cc: Noralf Trønnes <noralf@tronnes.org>
Cc: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Cc: Maxime Ripard <mripard@kernel.org>
Cc: Javier Martinez Canillas <javierm@redhat.com>
Cc: Russell King <linux@armlinux.org.uk>
Cc: Inki Dae <inki.dae@samsung.com>
Cc: Seung-Woo Kim <sw0312.kim@samsung.com>
Cc: Kyungmin Park <kyungmin.park@samsung.com>
Cc: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Cc: Patrik Jakobsson <patrik.r.jakobsson@gmail.com>
Cc: Rob Clark <robdclark@gmail.com>
Cc: Abhinav Kumar <quic_abhinavk@quicinc.com>
Cc: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Cc: Tomi Valkeinen <tomi.valkeinen@ideasonboard.com>
Cc: Alex Deucher <alexander.deucher@amd.com>
Cc: "Christian König" <christian.koenig@amd.com>
Cc: "Pan, Xinhui" <Xinhui.Pan@amd.com>
Cc: Thierry Reding <thierry.reding@gmail.com>
Cc: Mikko Perttunen <mperttunen@nvidia.com>
Cc: dri-devel@lists.freedesktop.org
Cc: linux-kernel@vger.kernel.org
Cc: linux-arm-kernel@lists.infradead.org
Cc: linux-samsung-soc@vger.kernel.org
Cc: linux-arm-msm@vger.kernel.org
Cc: freedreno@lists.freedesktop.org
Cc: amd-gfx@lists.freedesktop.org
Cc: linux-tegra@vger.kernel.org
Cc: dri-devel@lists.freedesktop.org
Cc: <stable@vger.kernel.org> # v5.2+
Reviewed-by: Javier Martinez Canillas <javierm@redhat.com>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org> # msm
Link: https://patchwork.freedesktop.org/patch/msgid/20230710091029.27503-1-tzimmermann@suse.de
|
|
Due to hardware limitation, MCAM drop rule with
ether_type == 802.1Q and vlan_id == 0 is not supported. Hence rejecting
such rules.
Fixes: dce677da57c0 ("octeontx2-pf: Add vlan-etype to ntuple filters")
Signed-off-by: Suman Ghosh <sumang@marvell.com>
Link: https://lore.kernel.org/r/20230710103027.2244139-1-sumang@marvell.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
Add info for the Archos 101 Cesium Educ tablet
It was tested using gslx680_ts_acpi module
PR at https://github.com/onitake/gsl-firmware/pull/210 for the firmware
Signed-off-by: Thomas GENTY <tomlohave@gmail.com>
Link: https://lore.kernel.org/r/20230707141425.21473-1-tomlohave@gmail.com
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
|
|
If for some reason a external function returns -ENODEV,
no error message is being displayed because the driver
assumes that -ENODEV can only be returned internally if
no sensors, etc where found.
Fix this by explicitly returning 0 in such a case since
missing hardware is no error. Also remove the now obsolete
check for -ENODEV.
Signed-off-by: Armin Wolf <W_Armin@gmx.de>
Link: https://lore.kernel.org/r/20230707010333.12954-1-W_Armin@gmx.de
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
|
|
Add new ACPI ID AMDI0103 used by upcoming AMD platform to the PMF
supported list of devices.
Signed-off-by: Shyam Sundar S K <Shyam-sundar.S-k@amd.com>
Link: https://lore.kernel.org/r/20230711100903.384151-1-Shyam-sundar.S-k@amd.com
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
|
|
Add new ACPI ID AMDI000A used by upcoming AMD platform to the pmc
supported list of devices
Signed-off-by: Shyam Sundar S K <Shyam-sundar.S-k@amd.com>
Link: https://lore.kernel.org/r/20230711100344.383948-1-Shyam-sundar.S-k@amd.com
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
|
|
HP 15s-eq2xxx is an older Lucienne laptop that has a problem resuming
from s2idle when IOMMU is enabled. The symptoms very closely resemble
that of the Lenovo issues with NVME resume. Lucienne was released in
a similar timeframe as the Renoir / Cezanne Lenovo laptops and they
may have similar BIOS code.
Applying the same quirk to this system allows the system to work with
IOMMU enabled and s2idle resume to work.
Link: https://gitlab.freedesktop.org/drm/amd/-/issues/2684
Signed-off-by: Mario Limonciello <mario.limonciello@amd.com>
Link: https://lore.kernel.org/r/20230710183934.17315-3-mario.limonciello@amd.com
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
|
|
It turns out that some-non Lenovo systems can benefit from the quirk
introduced for Lenovo systems in commit 455cd867b85b5 ("platform/x86:
thinkpad_acpi: Add a s2idle resume quirk for a number of laptops").
So move this quirk into running from the amd-pmc driver instead.
No intended functional changes.
Signed-off-by: Mario Limonciello <mario.limonciello@amd.com>
Link: https://lore.kernel.org/r/20230710183934.17315-2-mario.limonciello@amd.com
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
|
|
Remove unnecessary of_node_put from the continue path to prevent
child node from being released twice, which could avoid resource
leak or other unexpected issues.
Signed-off-by: Lu Hongfei <luhongfei@vivo.com>
Reviewed-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Fixes: de879a016a94 ("net: dsa: felix: add functionality when not all ports are supported")
Link: https://lore.kernel.org/r/20230710031859.36784-1-luhongfei@vivo.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
Commit a4d86249c773 ("drm/i915/gt: Provide a utility to create a scratch
buffer") mistakenly passed in uapi I915_CACHING_CACHED as argument to
i915_gem_object_set_cache_coherency(), which actually takes internal
enum i915_cache_level.
No functional issue since the value matches I915_CACHE_LLC (1 == 1), which
is the intended caching mode, but lets clean it up nevertheless.
Signed-off-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Fixes: a4d86249c773 ("drm/i915/gt: Provide a utility to create a scratch buffer")
Cc: Daniele Ceraolo Spurio <daniele.ceraolospurio@intel.com>
Reviewed-by: Tejas Upadhyay <tejas.upadhyay@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20230707125503.3965817-1-tvrtko.ursulin@linux.intel.com
(cherry picked from commit 49c60b2f0867ac36fd54d513882a48431aeccae7)
Signed-off-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
|
|
Commit 9275277d5324 ("drm/i915: use pat_index instead of cache_level")
added a dedicated gen12_pte_encode but forgot to remove the Gen12 specific
bit from gen8_pte_encode.
Signed-off-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Fixes: 9275277d5324 ("drm/i915: use pat_index instead of cache_level")
Cc: Fei Yang <fei.yang@intel.com>
Cc: Andi Shyti <andi.shyti@linux.intel.com>
Cc: Matt Roper <matthew.d.roper@intel.com>
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Reviewed-by: Fei Yang <fei.yang@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20230707124644.3965281-1-tvrtko.ursulin@linux.intel.com
(cherry picked from commit 08509377dd82ead98429785509f6b52a4b5f09f5)
Signed-off-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
|
|
For reports that are not powers of 2, reports at the end of the OA
buffer may get split across the buffer boundary. When zeroing out such
reports, take the split into consideration.
v2: Use OA_BUFFER_SIZE (Ashutosh)
Fixes: 09a36015d9a0 ("drm/i915/perf: Clear out entire reports after reading if not power of 2 size")
Signed-off-by: Umesh Nerlige Ramappa <umesh.nerlige.ramappa@intel.com>
Reviewed-by: Ashutosh Dixit <ashutosh.dixit@intel.com>
Signed-off-by: Ashutosh Dixit <ashutosh.dixit@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20230616173402.699776-1-umesh.nerlige.ramappa@intel.com
(cherry picked from commit 40b1588a750240cbe8a83117aa785d778749a77c)
Signed-off-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
|
|
If we are using Bigjoiner dpll_hw_state is supposed to be exactly
same as for master crtc, so no need to save it's state for slave crtc.
Signed-off-by: Stanislav Lisovskiy <stanislav.lisovskiy@intel.com>
Fixes: 0ff0e219d9b8 ("drm/i915: Compute clocks earlier")
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20230628141017.18937-1-stanislav.lisovskiy@intel.com
(cherry picked from commit cbaf758809952c95ec00e796695049babb08bb60)
Signed-off-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
|
|
In the case of heavy XDP traffic to be transmitted, the console
will print the error log continuously if there are lack of enough
BDs to accommodate the frames. The log looks like below.
[ 160.013112] fec 30be0000.ethernet eth0: NOT enough BD for SG!
[ 160.023116] fec 30be0000.ethernet eth0: NOT enough BD for SG!
[ 160.028926] fec 30be0000.ethernet eth0: NOT enough BD for SG!
[ 160.038946] fec 30be0000.ethernet eth0: NOT enough BD for SG!
[ 160.044758] fec 30be0000.ethernet eth0: NOT enough BD for SG!
Not only will this log be replicated and redundant, it will also
degrade XDP performance. So we use netdev_err_once() instead of
netdev_err() now.
Fixes: 6d6b39f180b8 ("net: fec: add initial XDP support")
Signed-off-by: Wei Fang <wei.fang@nxp.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
When the XDP feature is enabled and with heavy XDP frames to be
transmitted, there is a considerable probability that available
tx BDs are insufficient. This will lead to some XDP frames to be
discarded and the "NOT enough BD for SG!" error log will appear
in the console (as shown below).
[ 160.013112] fec 30be0000.ethernet eth0: NOT enough BD for SG!
[ 160.023116] fec 30be0000.ethernet eth0: NOT enough BD for SG!
[ 160.028926] fec 30be0000.ethernet eth0: NOT enough BD for SG!
[ 160.038946] fec 30be0000.ethernet eth0: NOT enough BD for SG!
[ 160.044758] fec 30be0000.ethernet eth0: NOT enough BD for SG!
In the case of heavy XDP traffic, sometimes the speed of recycling
tx BDs may be slower than the speed of sending XDP frames. There
may be several specific reasons, such as the interrupt is not
responsed in time, the efficiency of the NAPI callback function is
too low due to all the queues (tx queues and rx queues) share the
same NAPI, and so on.
After trying various methods, I think that increase the size of tx
BD ring is simple and effective. Maybe the best resolution is that
allocate NAPI for each queue to improve the efficiency of the NAPI
callback, but this change is a bit big and I didn't try this method.
Perheps this method will be implemented in a future patch.
This patch also updates the tx_wake_threshold of tx ring which is
related to the size of tx ring in the previous logic. Otherwise,
the tx_wake_threshold will be too high (403 BDs), which is more
likely to impact the slow path in the case of heavy XDP traffic,
because XDP path and slow path share the tx BD rings. According
to Jakub's suggestion, the tx_wake_threshold is at least equal to
tx_stop_threshold + 2 * MAX_SKB_FRAGS, if a queue of hundreds of
entries is overflowing, we should be able to apply a hysteresis
of a few tens of entries.
Fixes: 6d6b39f180b8 ("net: fec: add initial XDP support")
Signed-off-by: Wei Fang <wei.fang@nxp.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
Once the XDP frames have been successfully transmitted through the
ndo_xdp_xmit() interface, it's the driver responsibility to free
the frames so that the page_pool can recycle the pages and reuse
them. However, this action is not implemented in the fec driver.
This leads to a user-visible problem that the console will print
the following warning log.
[ 157.568851] page_pool_release_retry() stalled pool shutdown 1389 inflight 60 sec
[ 217.983446] page_pool_release_retry() stalled pool shutdown 1389 inflight 120 sec
[ 278.399006] page_pool_release_retry() stalled pool shutdown 1389 inflight 181 sec
[ 338.812885] page_pool_release_retry() stalled pool shutdown 1389 inflight 241 sec
[ 399.226946] page_pool_release_retry() stalled pool shutdown 1389 inflight 302 sec
Therefore, to solve this issue, we free XDP frames via xdp_return_frame()
while cleaning the tx BD ring.
Fixes: 6d6b39f180b8 ("net: fec: add initial XDP support")
Signed-off-by: Wei Fang <wei.fang@nxp.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
When a XDP program is installed or uninstalled, fec_restart() will
be invoked to reset MAC and buffer descriptor rings. It's reasonable
not to transmit any packet during the process of reset. However, the
NETDEV_XDP_ACT_NDO_XMIT bit of xdp_features is enabled by default,
that is to say, it's possible that the fec_enet_xdp_xmit() will be
invoked even if the process of reset is not finished. In this case,
the redirected XDP frames might be dropped and available transmit BDs
may be incorrectly deemed insufficient. So this patch disable the
NETDEV_XDP_ACT_NDO_XMIT feature by default and dynamically configure
this feature when the bpf program is installed or uninstalled.
Fixes: e4ac7cc6e5a4 ("net: fec: turn on XDP features")
Signed-off-by: Wei Fang <wei.fang@nxp.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
Boris needs 6.5-rc1 in drm-misc-fixes to prevent a conflict.
Signed-off-by: Maxime Ripard <mripard@kernel.org>
|
|
The insertion of an empty frame was introduced with
commit db0b124f02ba ("igc: Enhance Qbv scheduling by using first flag bit")
in order to ensure that the current cycle has at least one packet if
there is some packet to be scheduled for the next cycle.
However, the current implementation does not properly check if
a packet is already scheduled for the current cycle. Currently,
an empty packet is always inserted if and only if
txtime >= end_of_cycle && txtime > last_tx_cycle
but since last_tx_cycle is always either the end of the current
cycle (end_of_cycle) or the end of a previous cycle, the
second part (txtime > last_tx_cycle) is always true unless
txtime == last_tx_cycle.
What actually needs to be checked here is if the last_tx_cycle
was already written within the current cycle, so an empty frame
should only be inserted if and only if
txtime >= end_of_cycle && end_of_cycle > last_tx_cycle.
This patch does not only avoid an unnecessary insertion, but it
can actually be harmful to insert an empty packet if packets
are already scheduled in the current cycle, because it can lead
to a situation where the empty packet is actually processed
as the first packet in the upcoming cycle shifting the packet
with the first_flag even one cycle into the future, finally leading
to a TX hang.
The TX hang can be reproduced on a i225 with:
sudo tc qdisc replace dev enp1s0 parent root handle 100 taprio \
num_tc 1 \
map 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 \
queues 1@0 \
base-time 0 \
sched-entry S 01 300000 \
flags 0x1 \
txtime-delay 500000 \
clockid CLOCK_TAI
sudo tc qdisc replace dev enp1s0 parent 100:1 etf \
clockid CLOCK_TAI \
delta 500000 \
offload \
skip_sock_check
and traffic generator
sudo trafgen -i traffic.cfg -o enp1s0 --cpp -n0 -q -t1400ns
with traffic.cfg
#define ETH_P_IP 0x0800
{
/* Ethernet Header */
0x30, 0x1f, 0x9a, 0xd0, 0xf0, 0x0e, # MAC Dest - adapt as needed
0x24, 0x5e, 0xbe, 0x57, 0x2e, 0x36, # MAC Src - adapt as needed
const16(ETH_P_IP),
/* IPv4 Header */
0b01000101, 0, # IPv4 version, IHL, TOS
const16(1028), # IPv4 total length (UDP length + 20 bytes (IP header))
const16(2), # IPv4 ident
0b01000000, 0, # IPv4 flags, fragmentation off
64, # IPv4 TTL
17, # Protocol UDP
csumip(14, 33), # IPv4 checksum
/* UDP Header */
10, 0, 48, 1, # IP Src - adapt as needed
10, 0, 48, 10, # IP Dest - adapt as needed
const16(5555), # UDP Src Port
const16(6666), # UDP Dest Port
const16(1008), # UDP length (UDP header 8 bytes + payload length)
csumudp(14, 34), # UDP checksum
/* Payload */
fill('W', 1000),
}
and the observed message with that is for example
igc 0000:01:00.0 enp1s0: Detected Tx Unit Hang
Tx Queue <0>
TDH <32>
TDT <3c>
next_to_use <3c>
next_to_clean <32>
buffer_info[next_to_clean]
time_stamp <ffff26a8>
next_to_watch <00000000632a1828>
jiffies <ffff27f8>
desc.status <1048000>
Fixes: db0b124f02ba ("igc: Enhance Qbv scheduling by using first flag bit")
Signed-off-by: Florian Kauer <florian.kauer@linutronix.de>
Reviewed-by: Kurt Kanzenbach <kurt@linutronix.de>
Tested-by: Naama Meir <naamax.meir@linux.intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
|
|
It is possible (verified on a running system) that frames are processed
by igc_tx_launchtime with a txtime before the start of the cycle
(baset_est).
However, the result of txtime - baset_est is written into a u32,
leading to a wrap around to a positive number. The following
launchtime > 0 check will only branch to executing launchtime = 0
if launchtime is already 0.
Fix it by using a s32 before checking launchtime > 0.
Fixes: db0b124f02ba ("igc: Enhance Qbv scheduling by using first flag bit")
Signed-off-by: Florian Kauer <florian.kauer@linutronix.de>
Reviewed-by: Kurt Kanzenbach <kurt@linutronix.de>
Tested-by: Naama Meir <naamax.meir@linux.intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
|
|
The flags IGC_TXQCTL_STRICT_CYCLE and IGC_TXQCTL_STRICT_END
prevent the packet transmission over slot and cycle boundaries.
This is important for taprio offload where the slots and
cycles correspond to the slots and cycles configured for the
network.
However, the Qbv offload feature of the i225 is also used for
enabling TX launchtime / ETF offload. In that case, however,
the cycle has no meaning for the network and is only used
internally to adapt the base time register after a second has
passed.
Enabling strict mode in this case would unnecessarily prevent
the transmission of certain packets (i.e. at the boundary of a
second) and thus interferes with the ETF qdisc that promises
transmission at a certain point in time.
Similar to ETF, this also applies to CBS offload that also should
not be influenced by strict mode unless taprio offload would be
enabled at the same time.
This fully reverts
commit d8f45be01dd9 ("igc: Use strict cycles for Qbv scheduling")
but its commit message only describes what was already implemented
before that commit. The difference to a plain revert of that commit
is that it now copes with the base_time = 0 case that was fixed with
commit e17090eb2494 ("igc: allow BaseTime 0 enrollment for Qbv")
In particular, enabling strict mode leads to TX hang situations
under high traffic if taprio is applied WITHOUT taprio offload
but WITH ETF offload, e.g. as in
sudo tc qdisc replace dev enp1s0 parent root handle 100 taprio \
num_tc 1 \
map 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 \
queues 1@0 \
base-time 0 \
sched-entry S 01 300000 \
flags 0x1 \
txtime-delay 500000 \
clockid CLOCK_TAI
sudo tc qdisc replace dev enp1s0 parent 100:1 etf \
clockid CLOCK_TAI \
delta 500000 \
offload \
skip_sock_check
and traffic generator
sudo trafgen -i traffic.cfg -o enp1s0 --cpp -n0 -q -t1400ns
with traffic.cfg
#define ETH_P_IP 0x0800
{
/* Ethernet Header */
0x30, 0x1f, 0x9a, 0xd0, 0xf0, 0x0e, # MAC Dest - adapt as needed
0x24, 0x5e, 0xbe, 0x57, 0x2e, 0x36, # MAC Src - adapt as needed
const16(ETH_P_IP),
/* IPv4 Header */
0b01000101, 0, # IPv4 version, IHL, TOS
const16(1028), # IPv4 total length (UDP length + 20 bytes (IP header))
const16(2), # IPv4 ident
0b01000000, 0, # IPv4 flags, fragmentation off
64, # IPv4 TTL
17, # Protocol UDP
csumip(14, 33), # IPv4 checksum
/* UDP Header */
10, 0, 48, 1, # IP Src - adapt as needed
10, 0, 48, 10, # IP Dest - adapt as needed
const16(5555), # UDP Src Port
const16(6666), # UDP Dest Port
const16(1008), # UDP length (UDP header 8 bytes + payload length)
csumudp(14, 34), # UDP checksum
/* Payload */
fill('W', 1000),
}
and the observed message with that is for example
igc 0000:01:00.0 enp1s0: Detected Tx Unit Hang
Tx Queue <0>
TDH <d0>
TDT <f0>
next_to_use <f0>
next_to_clean <d0>
buffer_info[next_to_clean]
time_stamp <ffff661f>
next_to_watch <00000000245a4efb>
jiffies <ffff6e48>
desc.status <1048000>
Fixes: d8f45be01dd9 ("igc: Use strict cycles for Qbv scheduling")
Signed-off-by: Florian Kauer <florian.kauer@linutronix.de>
Reviewed-by: Kurt Kanzenbach <kurt@linutronix.de>
Tested-by: Naama Meir <naamax.meir@linux.intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
|
|
Replace occurences of the pattern "PAGE_SHIFT - 9" in the passthru and
loop targets with PAGE_SECTORS_SHIFT.
Signed-off-by: Damien Le Moal <dlemoal@kernel.org>
Reviewed-by: Chaitanya Kulkarni <kch@nvidia.com>
Reviewed-by: Sagi Grimberg <sagi@grimberg.me>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Keith Busch <kbusch@kernel.org>
|
|
Add the quirk as SM953 is reporting bogus namespace ID.
Link: https://bugzilla.kernel.org/show_bug.cgi?id=217593
Reported-by: Clemens Springsguth <cspringsguth@gmail.com>
Tested-by: Clemens Springsguth <cspringsguth@gmail.com>
Signed-off-by: Pankaj Raghav <p.raghav@samsung.com>
Signed-off-by: Keith Busch <kbusch@kernel.org>
|
|
Since commit e17090eb2494 ("igc: allow BaseTime 0 enrollment for Qbv")
it is possible to enable taprio offload with a basetime of 0.
However, the check if taprio offload is already enabled (and thus -EALREADY
should be returned for igc_save_qbv_schedule) still relied on
adapter->base_time > 0.
This can be reproduced as follows:
# TAPRIO offload (flags == 0x2) and base-time = 0
sudo tc qdisc replace dev enp1s0 parent root handle 100 stab overhead 24 taprio \
num_tc 1 \
map 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 \
queues 1@0 \
base-time 0 \
sched-entry S 01 300000 \
flags 0x2
# The second call should fail with "Error: Device failed to setup taprio offload."
# But that only happens if base-time was != 0
sudo tc qdisc replace dev enp1s0 parent root handle 100 stab overhead 24 taprio \
num_tc 1 \
map 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 \
queues 1@0 \
base-time 0 \
sched-entry S 01 300000 \
flags 0x2
Fixes: e17090eb2494 ("igc: allow BaseTime 0 enrollment for Qbv")
Signed-off-by: Florian Kauer <florian.kauer@linutronix.de>
Reviewed-by: Kurt Kanzenbach <kurt@linutronix.de>
Tested-by: Naama Meir <naamax.meir@linux.intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
|
|
Only set adapter->taprio_offload_enable after validating the arguments.
Otherwise, it stays set even if the offload was not enabled.
Since the subsequent code does not get executed in case of invalid
arguments, it will not be read at first.
However, by activating and then deactivating another offload
(e.g. ETF/TX launchtime offload), taprio_offload_enable is read
and erroneously keeps the offload feature of the NIC enabled.
This can be reproduced as follows:
# TAPRIO offload (flags == 0x2) and negative base-time leading to expected -ERANGE
sudo tc qdisc replace dev enp1s0 parent root handle 100 stab overhead 24 taprio \
num_tc 1 \
map 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 \
queues 1@0 \
base-time -1000 \
sched-entry S 01 300000 \
flags 0x2
# IGC_TQAVCTRL is 0x0 as expected (iomem=relaxed for reading register)
sudo pcimem /sys/bus/pci/devices/0000:01:00.0/resource0 0x3570 w*1
# Activate ETF offload
sudo tc qdisc replace dev enp1s0 parent root handle 6666 mqprio \
num_tc 3 \
map 2 2 1 0 2 2 2 2 2 2 2 2 2 2 2 2 \
queues 1@0 1@1 2@2 \
hw 0
sudo tc qdisc add dev enp1s0 parent 6666:1 etf \
clockid CLOCK_TAI \
delta 500000 \
offload
# IGC_TQAVCTRL is 0x9 as expected
sudo pcimem /sys/bus/pci/devices/0000:01:00.0/resource0 0x3570 w*1
# Deactivate ETF offload again
sudo tc qdisc delete dev enp1s0 parent 6666:1
# IGC_TQAVCTRL should now be 0x0 again, but is observed as 0x9
sudo pcimem /sys/bus/pci/devices/0000:01:00.0/resource0 0x3570 w*1
Fixes: e17090eb2494 ("igc: allow BaseTime 0 enrollment for Qbv")
Signed-off-by: Florian Kauer <florian.kauer@linutronix.de>
Reviewed-by: Kurt Kanzenbach <kurt@linutronix.de>
Tested-by: Naama Meir <naamax.meir@linux.intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
|
|
In the current implementation the flags adapter->qbv_enable
and IGC_FLAG_TSN_QBV_ENABLED have a similar name, but do not
have the same meaning. The first one is used only to indicate
taprio offload (i.e. when igc_save_qbv_schedule was called),
while the second one corresponds to the Qbv mode of the hardware.
However, the second one is also used to support the TX launchtime
feature, i.e. ETF qdisc offload. This leads to situations where
adapter->qbv_enable is false, but the flag IGC_FLAG_TSN_QBV_ENABLED
is set. This is prone to confusion.
The rename should reduce this confusion. Since it is a pure
rename, it has no impact on functionality.
Fixes: e17090eb2494 ("igc: allow BaseTime 0 enrollment for Qbv")
Signed-off-by: Florian Kauer <florian.kauer@linutronix.de>
Reviewed-by: Kurt Kanzenbach <kurt@linutronix.de>
Tested-by: Naama Meir <naamax.meir@linux.intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
|
|
skl_int3472_regulator_second_sensor storage-class-specifier to static
smatch reports
drivers/platform/x86/intel/int3472/clk_and_regulator.c:263:28: warning: symbol
'skl_int3472_regulator_second_sensor' was not declared. Should it be static?
This variable is only used in its defining file, so it should be static.
Signed-off-by: Tom Rix <trix@redhat.com>
Link: https://lore.kernel.org/r/20230702134419.3438361-1-trix@redhat.com
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
|
|
cap_offset is a u16 field, so multiplying with TPMI_CAP_OFFSET_UNIT
(which is equal to 1024) to covert to bytes will cause overflow. This
will be a problem once more TPMI features are added.
This field is not used except for calculating pfs->vsec_offset. So, leave
cap_offset field unchanged and multiply with TPMI_CAP_OFFSET_UNIT while
calculating pfs->vsec_offset.
Signed-off-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Link: https://lore.kernel.org/r/20230622195717.3125088-1-srinivas.pandruvada@linux.intel.com
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
|
|
Even though we have no issues in the code, let's replace the open
coded guid_parse_and_compare().
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20230621151155.78279-2-andriy.shevchenko@linux.intel.com
Tested-by: Armin Wolf <W_Armin@gmx.de>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
|
|
The while-loop may break on one of the two conditions, either ID string
is empty or GUID matches. The second one, may never be reached if the
parsed string is not correct GUID. In such a case the loop will never
advance to check the next ID.
Break possible infinite loop by factoring out guid_parse_and_compare()
helper which may be moved to the generic header for everyone later on
and preventing from similar mistake in the future.
Interestingly that firstly it appeared when WMI was turned into a bus
driver, but later when duplicated GUIDs were checked, the while-loop
has been replaced by for-loop and hence no mistake made again.
Fixes: a48e23385fcf ("platform/x86: wmi: add context pointer field to struct wmi_device_id")
Fixes: 844af950da94 ("platform/x86: wmi: Turn WMI into a bus driver")
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20230621151155.78279-1-andriy.shevchenko@linux.intel.com
Tested-by: Armin Wolf <W_Armin@gmx.de>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
|
|
There is a small window where we have already incremented the pin count
but not yet moved the bo from the lru to the pinned list.
Signed-off-by: Christian König <christian.koenig@amd.com>
Reported-by: Pelloux-Prayer, Pierre-Eric <Pierre-eric.Pelloux-prayer@amd.com>
Tested-by: Pelloux-Prayer, Pierre-Eric <Pierre-eric.Pelloux-prayer@amd.com>
Acked-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org
Link: https://patchwork.freedesktop.org/patch/msgid/20230707120826.3701-1-christian.koenig@amd.com
|
|
The command word is defined as following:
/* Command */
#define SPI_CMD_COMMAND_SHIFT 0
#define SPI_CMD_DEVICE_ID_SHIFT 4
#define SPI_CMD_PREPEND_BYTE_CNT_SHIFT 8
#define SPI_CMD_ONE_BYTE_SHIFT 11
#define SPI_CMD_ONE_WIRE_SHIFT 12
If the prepend byte count field starts at bit 8, and the next defined
bit is SPI_CMD_ONE_BYTE at bit 11, it can be at most 3 bits wide, and
thus the max value is 7, not 15.
Fixes: b17de076062a ("spi/bcm63xx: work around inability to keep CS up")
Signed-off-by: Jonas Gorski <jonas.gorski@gmail.com>
Link: https://lore.kernel.org/r/20230629071453.62024-1-jonas.gorski@gmail.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Currently, sd1 and sd0 have unique subnode names 'sd1_mux' and 'sd0_mux'.
If we change these to non-unique subnode names such as 'mux' this can
lead to the below conflict as the RZ/G2L pin control driver considers
only the names of the subnodes.
pinctrl-rzg2l 11030000.pinctrl: pin P47_0 already requested by 11c00000.mmc; cannot claim for 11c10000.mmc
pinctrl-rzg2l 11030000.pinctrl: pin-376 (11c10000.mmc) status -22
pinctrl-rzg2l 11030000.pinctrl: could not request pin 376 (P47_0) from group mux on device pinctrl-rzg2l
renesas_sdhi_internal_dmac 11c10000.mmc: Error applying setting, reverse things back
Fix this by constructing unique names from the node names of both the
pin control configuration node and its child node, where appropriate.
Based on the work done by Geert for the RZ/V2M pinctrl driver.
Fixes: c4c4637eb57f ("pinctrl: renesas: Add RZ/G2L pin and gpio controller driver")
Signed-off-by: Biju Das <biju.das.jz@bp.renesas.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/r/20230704111858.215278-1-biju.das.jz@bp.renesas.com
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
|
|
The eMMC and SDHI pin control configuration nodes in DT have subnodes
with the same names ("data" and "ctrl"). As the RZ/V2M pin control
driver considers only the names of the subnodes, this leads to
conflicts:
pinctrl-rzv2m b6250000.pinctrl: pin P8_2 already requested by 85000000.mmc; cannot claim for 85020000.mmc
pinctrl-rzv2m b6250000.pinctrl: pin-130 (85020000.mmc) status -22
renesas_sdhi_internal_dmac 85020000.mmc: Error applying setting, reverse things back
Fix this by constructing unique names from the node names of both the
pin control configuration node and its child node, where appropriate.
Reported by: Fabrizio Castro <fabrizio.castro.jz@renesas.com>
Fixes: 92a9b825257614af ("pinctrl: renesas: Add RZ/V2M pin and gpio controller driver")
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Tested-by: Fabrizio Castro <fabrizio.castro.jz@renesas.com>
Link: https://lore.kernel.org/r/607bd6ab4905b0b1b119a06ef953fa1184505777.1688396717.git.geert+renesas@glider.be
|
|
Shift operation of 'exp' and 'shift' variables exceeds the maximum number
of shift values in the u32 range leading to UBSAN shift-out-of-bounds.
...
[ 6.120512] UBSAN: shift-out-of-bounds in drivers/hid/amd-sfh-hid/sfh1_1/amd_sfh_desc.c:149:50
[ 6.120598] shift exponent 104 is too large for 64-bit type 'long unsigned int'
[ 6.120659] CPU: 4 PID: 96 Comm: kworker/4:1 Not tainted 6.4.0amd_1-next-20230519-dirty #10
[ 6.120665] Hardware name: AMD Birman-PHX/Birman-PHX, BIOS SFH_with_HPD_SEN.FD 04/05/2023
[ 6.120667] Workqueue: events amd_sfh_work_buffer [amd_sfh]
[ 6.120687] Call Trace:
[ 6.120690] <TASK>
[ 6.120694] dump_stack_lvl+0x48/0x70
[ 6.120704] dump_stack+0x10/0x20
[ 6.120707] ubsan_epilogue+0x9/0x40
[ 6.120716] __ubsan_handle_shift_out_of_bounds+0x10f/0x170
[ 6.120720] ? psi_group_change+0x25f/0x4b0
[ 6.120729] float_to_int.cold+0x18/0xba [amd_sfh]
[ 6.120739] get_input_rep+0x57/0x340 [amd_sfh]
[ 6.120748] ? __schedule+0xba7/0x1b60
[ 6.120756] ? __pfx_get_input_rep+0x10/0x10 [amd_sfh]
[ 6.120764] amd_sfh_work_buffer+0x91/0x180 [amd_sfh]
[ 6.120772] process_one_work+0x229/0x430
[ 6.120780] worker_thread+0x4a/0x3c0
[ 6.120784] ? __pfx_worker_thread+0x10/0x10
[ 6.120788] kthread+0xf7/0x130
[ 6.120792] ? __pfx_kthread+0x10/0x10
[ 6.120795] ret_from_fork+0x29/0x50
[ 6.120804] </TASK>
...
Fix this by adding the condition to validate shift ranges.
Fixes: 93ce5e0231d7 ("HID: amd_sfh: Implement SFH1.1 functionality")
Cc: stable@vger.kernel.org
Tested-by: Kai-Heng Feng <kai.heng.feng@canonical.com>
Signed-off-by: Basavaraj Natikar <Basavaraj.Natikar@amd.com>
Signed-off-by: Akshata MukundShetty <akshata.mukundshetty@amd.com>
Link: https://lore.kernel.org/r/20230707065722.9036-3-Basavaraj.Natikar@amd.com
Signed-off-by: Benjamin Tissoires <bentiss@kernel.org>
|
|
As float32 is also used in other places as a data type, it is necessary
to rename the float32 variable in order to avoid confusion.
Cc: stable@vger.kernel.org
Tested-by: Kai-Heng Feng <kai.heng.feng@canonical.com>
Signed-off-by: Basavaraj Natikar <Basavaraj.Natikar@amd.com>
Signed-off-by: Akshata MukundShetty <akshata.mukundshetty@amd.com>
Link: https://lore.kernel.org/r/20230707065722.9036-2-Basavaraj.Natikar@amd.com
Signed-off-by: Benjamin Tissoires <bentiss@kernel.org>
|
|
Current codebase contained the usage of two different names for this
driver (i.e., `gvnic` and `gve`), which is quite unfriendly for users
to use, especially when trying to bind or unbind the driver manually.
The corresponding kernel module is registered with the name of `gve`.
It's more reasonable to align the name of the driver with the module.
Fixes: 893ce44df565 ("gve: Add basic driver framework for Compute Engine Virtual NIC")
Cc: csully@google.com
Signed-off-by: Junfeng Guo <junfeng.guo@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add check for the return value of skb_copy in order to avoid NULL pointer
dereference.
Fixes: 2cd548566384 ("net: dsa: qca8k: add support for phy read/write with mgmt Ethernet")
Signed-off-by: Jiasheng Jiang <jiasheng@iscas.ac.cn>
Reviewed-by: Pavan Chebbi <pavan.chebbi@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Pull NTB updates from Jon Mason:
"Fixes for pci_clean_master, error handling in driver inits, and
various other issues/bugs"
* tag 'ntb-6.5' of https://github.com/jonmason/ntb:
ntb: hw: amd: Fix debugfs_create_dir error checking
ntb.rst: Fix copy and paste error
ntb_netdev: Fix module_init problem
ntb: intel: Remove redundant pci_clear_master
ntb: epf: Remove redundant pci_clear_master
ntb_hw_amd: Remove redundant pci_clear_master
ntb: idt: drop redundant pci_enable_pcie_error_reporting()
MAINTAINERS: git://github -> https://github.com for jonmason
NTB: EPF: fix possible memory leak in pci_vntb_probe()
NTB: ntb_tool: Add check for devm_kcalloc
NTB: ntb_transport: fix possible memory leak while device_register() fails
ntb: intel: Fix error handling in intel_ntb_pci_driver_init()
NTB: amd: Fix error handling in amd_ntb_pci_driver_init()
ntb: idt: Fix error handling in idt_pci_driver_init()
|
|
Commit 9f4211bf7f81 ("HID: add mapping for camera access keys") added
mapping for the camera access keys, but unfortunately used wrong usage
codes for them. HUTRR72[1] specifies that camera access controls use 0x76,
0x077 and 0x78 usages in the consumer control page. Previously mapped 0xd5,
0xd6 and 0xd7 usages are actually defined in HUTRR64[2] as game recording
controls.
[1] https://www.usb.org/sites/default/files/hutrr72_-_usages_to_control_camera_access_0.pdf
[2] https://www.usb.org/sites/default/files/hutrr64b_-_game_recording_controllers_0.pdf
Fixes: 9f4211bf7f81 ("HID: add mapping for camera access keys")
Cc: stable@vger.kernel.org
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Link: https://lore.kernel.org/r/ZJtd/fMXRUgq20TW@google.com
Signed-off-by: Benjamin Tissoires <bentiss@kernel.org>
|
|
Previously, support for the G502 had been attempted in commit
'27fc32fd9417 ("HID: logitech-hidpp: add USB PID for a few more supported
mice")'
This caused some issues and was reverted by
'addf3382c47c ("Revert "HID: logitech-hidpp: add USB PID for a few more
supported mice"")'.
Since then, a new version of this mouse has been released (Lightpseed
Wireless), and works correctly.
This device has support for battery reporting with the driver
Signed-off-by: Stuart Hayhurst <stuart.a.hayhurst@gmail.com>
Reviewed-by: Bastien Nocera <hadess@hadess.net>
Link: https://lore.kernel.org/r/20230630113818.13005-1-stuart.a.hayhurst@gmail.com
Signed-off-by: Benjamin Tissoires <bentiss@kernel.org>
|
|
Match alignment information in composite type declarations used by packed
HOSTCMD report structures. Compiler packing attribute is not recursive for
inner declarations. Mismatched alignment information can cause undefined
behavior in code generated for accessing composite type members. struct
pointers passed to thunderstrike_parse_board_info_payload and
thunderstrike_parse_haptics_payload are an example of this being
potentially problematic since alignment information from the packed HOSTCMD
report is lost.
Reported-by: kernel test robot <lkp@intel.com>
Closes: https://lore.kernel.org/oe-kbuild-all/202307041500.6bKn7nCl-lkp@intel.com/
Link: https://github.com/llvm/llvm-project/issues/55520#issuecomment-1128617570
Link: https://gcc.gnu.org/onlinedocs/gcc-13.1.0/gcc/Common-Type-Attributes.html#index-packed-type-attribute
Signed-off-by: Rahul Rameshbabu <rrameshbabu@nvidia.com>
Link: https://lore.kernel.org/r/20230705060414.581468-1-rrameshbabu@nvidia.com
Signed-off-by: Benjamin Tissoires <bentiss@kernel.org>
|
|
A previous patch addressed the fortified memcpy warning for most
builds, but I still see this one with gcc-9:
In file included from include/linux/string.h:254,
from drivers/hid/hid-hyperv.c:8:
In function 'fortify_memcpy_chk',
inlined from 'mousevsc_on_receive' at drivers/hid/hid-hyperv.c:272:3:
include/linux/fortify-string.h:583:4: error: call to '__write_overflow_field' declared with attribute warning: detected write beyond size of field (1st parameter); maybe use struct_group()? [-Werror=attribute-warning]
583 | __write_overflow_field(p_size_field, size);
| ^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
My guess is that the WARN_ON() itself is what confuses gcc, so it no
longer sees that there is a correct range check. Rework the code in a
way that helps readability and avoids the warning.
Fixes: 542f25a94471 ("HID: hyperv: Replace one-element array with flexible-array member")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: Michael Kelley <mikelley@microsoft.com>
Link: https://lore.kernel.org/r/20230705140242.844167-1-arnd@kernel.org
Signed-off-by: Benjamin Tissoires <bentiss@kernel.org>
|
|
The blamed commit introduces usage of fixed_phy_register() but
not a corresponding dependency on FIXED_PHY.
This can result in a build failure.
s390-linux-ld: drivers/net/ethernet/microchip/lan743x_main.o: in function `lan743x_phy_open':
drivers/net/ethernet/microchip/lan743x_main.c:1514: undefined reference to `fixed_phy_register'
Fixes: 624864fbff92 ("net: lan743x: add fixed phy support for LAN7431 device")
Cc: stable@vger.kernel.org
Reported-by: Randy Dunlap <rdunlap@infradead.org>
Closes: https://lore.kernel.org/netdev/725bf1c5-b252-7d19-7582-a6809716c7d6@infradead.org/
Reviewed-by: Randy Dunlap <rdunlap@infradead.org>
Tested-by: Randy Dunlap <rdunlap@infradead.org> # build-tested
Signed-off-by: Simon Horman <horms@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Pull more SCSI updates from James Bottomley:
"A few late arriving patches that missed the initial pull request. It's
mostly bug fixes (the dt-bindings is a fix for the initial pull)"
* tag 'scsi-misc' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi:
scsi: ufs: core: Remove unused function declaration
scsi: target: docs: Remove tcm_mod_builder.py
scsi: target: iblock: Quiet bool conversion warning with pr_preempt use
scsi: dt-bindings: ufs: qcom: Fix ICE phandle
scsi: core: Simplify scsi_cdl_check_cmd()
scsi: isci: Fix comment typo
scsi: smartpqi: Replace one-element arrays with flexible-array members
scsi: target: tcmu: Replace strlcpy() with strscpy()
scsi: ncr53c8xx: Replace strlcpy() with strscpy()
scsi: lpfc: Fix lpfc_name struct packing
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux
Pull more i2c updates from Wolfram Sang:
- xiic patch should have been in the original pull but slipped through
- mpc patch fixes a build regression
- nomadik cleanup
* tag 'i2c-for-6.5-rc1-part2' of git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux:
i2c: mpc: Drop unused variable
i2c: nomadik: Remove a useless call in the remove function
i2c: xiic: Don't try to handle more interrupt events after error
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/kees/linux
Pull hardening fixes from Kees Cook:
- Check for NULL bdev in LoadPin (Matthias Kaehlcke)
- Revert unwanted KUnit FORTIFY build default
- Fix 1-element array causing boot warnings with xhci-hub
* tag 'hardening-v6.5-rc1-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/kees/linux:
usb: ch9: Replace bmSublinkSpeedAttr 1-element array with flexible array
Revert "fortify: Allow KUnit test to build without FORTIFY"
dm: verity-loadpin: Add NULL pointer check for 'bdev' parameter
|
|
The debugfs_create_dir function returns ERR_PTR in case of error, and the
only correct way to check if an error occurred is 'IS_ERR' inline function.
This patch will replace the null-comparison with IS_ERR.
Signed-off-by: Anup Sharma <anupnewsmail@gmail.com>
Suggested-by: Ivan Orlov <ivan.orlov0322@gmail.com>
Signed-off-by: Jon Mason <jdmason@kudzu.us>
|
