summaryrefslogtreecommitdiff
path: root/drivers
AgeCommit message (Collapse)Author
2025-05-02xen: Change xen-acpi-processor dom0 dependencyJason Andryuk
[ Upstream commit 0f2946bb172632e122d4033e0b03f85230a29510 ] xen-acpi-processor functions under a PVH dom0 with only a xen_initial_domain() runtime check. Change the Kconfig dependency from PV dom0 to generic dom0 to reflect that. Suggested-by: Jan Beulich <jbeulich@suse.com> Signed-off-by: Jason Andryuk <jason.andryuk@amd.com> Reviewed-by: Juergen Gross <jgross@suse.com> Tested-by: Jan Beulich <jbeulich@suse.com> Signed-off-by: Juergen Gross <jgross@suse.com> Message-ID: <20250331172913.51240-1-jason.andryuk@amd.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
2025-05-02rtc: pcf85063: do a SW reset if POR failedLukas Stockmann
[ Upstream commit 2b7cbd98495f6ee4cd6422fe77828a19e9edf87f ] Power-on Reset has a documented issue in PCF85063, refer to its datasheet, section "Software reset": "There is a low probability that some devices will have corruption of the registers after the automatic power-on reset if the device is powered up with a residual VDD level. It is required that the VDD starts at zero volts at power up or upon power cycling to ensure that there is no corruption of the registers. If this is not possible, a reset must be initiated after power-up (i.e. when power is stable) with the software reset command" Trigger SW reset if there is an indication that POR has failed. Link: https://www.nxp.com/docs/en/data-sheet/PCF85063A.pdf Signed-off-by: Lukas Stockmann <lukas.stockmann@siemens.com> Signed-off-by: Alexander Sverdlin <alexander.sverdlin@siemens.com> Link: https://lore.kernel.org/r/20250120093451.30778-1-alexander.sverdlin@siemens.com Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
2025-05-02ntb_hw_amd: Add NTB PCI ID for new gen CPUBasavaraj Natikar
[ Upstream commit bf8a7ce7e4c7267a6f5f2b2023cfc459b330b25e ] Add NTB support for new generation of processor. Signed-off-by: Basavaraj Natikar <Basavaraj.Natikar@amd.com> Signed-off-by: Jon Mason <jdmason@kudzu.us> Signed-off-by: Sasha Levin <sashal@kernel.org>
2025-05-02ntb: reduce stack usage in idt_scan_mwsArnd Bergmann
[ Upstream commit aff12700b8dd7422bfe2277696e192af4df9de8f ] idt_scan_mws() puts a large fixed-size array on the stack and copies it into a smaller dynamically allocated array at the end. On 32-bit targets, the fixed size can easily exceed the warning limit for possible stack overflow: drivers/ntb/hw/idt/ntb_hw_idt.c:1041:27: error: stack frame size (1032) exceeds limit (1024) in 'idt_scan_mws' [-Werror,-Wframe-larger-than] Change it to instead just always use dynamic allocation for the array from the start. It's too big for the stack, but not actually all that much for a permanent allocation. Reported-by: kernel test robot <lkp@intel.com> Closes: https://lore.kernel.org/all/202205111109.PiKTruEj-lkp@intel.com/ Signed-off-by: Arnd Bergmann <arnd@arndb.de> Reviewed-by: Dave Jiang <dave.jiang@intel.com> Reviewed-by: Damien Le Moal <dlemoal@kernel.org> Signed-off-by: Jon Mason <jdmason@kudzu.us> Signed-off-by: Sasha Levin <sashal@kernel.org>
2025-05-02qibfs: fix _another_ leakAl Viro
[ Upstream commit bdb43af4fdb39f844ede401bdb1258f67a580a27 ] failure to allocate inode => leaked dentry... this one had been there since the initial merge; to be fair, if we are that far OOM, the odds of failing at that particular allocation are low... Signed-off-by: Al Viro <viro@zeniv.linux.org.uk> Signed-off-by: Sasha Levin <sashal@kernel.org>
2025-05-02objtool, lkdtm: Obfuscate the do_nothing() pointerJosh Poimboeuf
[ Upstream commit 05026ea01e95ffdeb0e5ac8fb7fb1b551e3a8726 ] If execute_location()'s memcpy of do_nothing() gets inlined and unrolled by the compiler, it copies one word at a time: mov 0x0(%rip),%rax R_X86_64_PC32 .text+0x1374 mov %rax,0x38(%rbx) mov 0x0(%rip),%rax R_X86_64_PC32 .text+0x136c mov %rax,0x30(%rbx) ... Those .text references point to the middle of the function, causing objtool to complain about their lack of ENDBR. Prevent that by resolving the function pointer at runtime rather than build time. This fixes the following warning: drivers/misc/lkdtm/lkdtm.o: warning: objtool: execute_location+0x23: relocation to !ENDBR: .text+0x1378 Reported-by: kernel test robot <lkp@intel.com> Signed-off-by: Josh Poimboeuf <jpoimboe@kernel.org> Signed-off-by: Ingo Molnar <mingo@kernel.org> Reviewed-by: Kees Cook <kees@kernel.org> Cc: Arnd Bergmann <arnd@arndb.de> Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Cc: Linus Torvalds <torvalds@linux-foundation.org> Link: https://lore.kernel.org/r/30b9abffbddeb43c4f6320b1270fa9b4d74c54ed.1742852847.git.jpoimboe@kernel.org Closes: https://lore.kernel.org/oe-kbuild-all/202503191453.uFfxQy5R-lkp@intel.com/ Signed-off-by: Sasha Levin <sashal@kernel.org>
2025-05-02objtool, regulator: rk808: Remove potential undefined behavior in ↵Josh Poimboeuf
rk806_set_mode_dcdc() [ Upstream commit 29c578c848402a34e8c8e115bf66cb6008b77062 ] If 'ctr_bit' is negative, the shift counts become negative, causing a shift of bounds and undefined behavior. Presumably that's not possible in normal operation, but the code generation isn't optimal. And undefined behavior should be avoided regardless. Improve code generation and remove the undefined behavior by converting the signed variables to unsigned. Fixes the following warning with an UBSAN kernel: vmlinux.o: warning: objtool: rk806_set_mode_dcdc() falls through to next function rk806_get_mode_dcdc() vmlinux.o: warning: objtool: .text.rk806_set_mode_dcdc: unexpected end of section Reported-by: kernel test robot <lkp@intel.com> Signed-off-by: Josh Poimboeuf <jpoimboe@kernel.org> Signed-off-by: Ingo Molnar <mingo@kernel.org> Acked-by: Mark Brown <broonie@kernel.org> Cc: Liam Girdwood <lgirdwood@gmail.com> Cc: Linus Torvalds <torvalds@linux-foundation.org> Link: https://lore.kernel.org/r/2023abcddf3f524ba478d64339996f25dc4097d2.1742852847.git.jpoimboe@kernel.org Closes: https://lore.kernel.org/oe-kbuild-all/202503182350.52KeHGD4-lkp@intel.com/ Signed-off-by: Sasha Levin <sashal@kernel.org>
2025-05-02thunderbolt: Scan retimers after device router has been enumeratedMika Westerberg
[ Upstream commit 75749d2c1d8cef439f8b69fa1f4f36d0fc3193e6 ] Thomas reported connection issues on AMD system with Pluggable UD-4VPD dock. After some experiments it looks like the device has some sort of internal timeout that triggers reconnect. This is completely against the USB4 spec, as there is no requirement for the host to enumerate the device right away or even at all. In Linux case the delay is caused by scanning of retimers on the link so we can work this around by doing the scanning after the device router has been enumerated. Reported-by: Thomas Lynema <lyz27@yahoo.com> Closes: https://bugzilla.kernel.org/show_bug.cgi?id=219748 Reviewed-by: Mario Limonciello <mario.limonciello@amd.com> Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
2025-05-02usb: host: xhci-plat: mvebu: use ->quirks instead of ->init_quirk() funcThéo Lebrun
[ Upstream commit 64eb182d5f7a5ec30227bce4f6922ff663432f44 ] Compatible "marvell,armada3700-xhci" match data uses the struct xhci_plat_priv::init_quirk() function pointer to add XHCI_RESET_ON_RESUME as quirk on XHCI. Instead, use the struct xhci_plat_priv::quirks field. Signed-off-by: Théo Lebrun <theo.lebrun@bootlin.com> Link: https://lore.kernel.org/r/20250205-s2r-cdns-v7-1-13658a271c3c@bootlin.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
2025-05-02usb: gadget: aspeed: Add NULL pointer check in ast_vhub_init_dev()Chenyuan Yang
[ Upstream commit 8c75f3e6a433d92084ad4e78b029ae680865420f ] The variable d->name, returned by devm_kasprintf(), could be NULL. A pointer check is added to prevent potential NULL pointer dereference. This is similar to the fix in commit 3027e7b15b02 ("ice: Fix some null pointer dereference issues in ice_ptp.c"). This issue is found by our static analysis tool Signed-off-by: Chenyuan Yang <chenyuan0y@gmail.com> Link: https://lore.kernel.org/r/20250311012705.1233829-1-chenyuan0y@gmail.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
2025-05-02phy: rockchip: usbdp: Avoid call hpd_event_trigger in dp_phy_initAndy Yan
[ Upstream commit 28dc672a1a877c77b000c896abd8f15afcdc1b0c ] Function rk_udphy_dp_hpd_event_trigger will set vogrf let it trigger HPD interrupt to DP by Type-C. This configuration is only required when the DP work in Alternate Mode, and called by typec_mux_set. In standard DP mode, such settings will prevent the DP from receiving HPD interrupts. Signed-off-by: Andy Yan <andy.yan@rock-chips.com> Link: https://lore.kernel.org/r/20250302115257.188774-1-andyshrk@163.com Signed-off-by: Vinod Koul <vkoul@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
2025-05-02usb: xhci: Avoid Stop Endpoint retry loop if the endpoint seems RunningMichal Pecio
[ Upstream commit 28a76fcc4c85dd39633fb96edb643c91820133e3 ] Nothing prevents a broken HC from claiming that an endpoint is Running and repeatedly rejecting Stop Endpoint with Context State Error. Avoid infinite retries and give back cancelled TDs. No such cases known so far, but HCs have bugs. Signed-off-by: Michal Pecio <michal.pecio@gmail.com> Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com> Link: https://lore.kernel.org/r/20250311154551.4035726-4-mathias.nyman@linux.intel.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
2025-05-02dmaengine: dmatest: Fix dmatest waiting less when interruptedVinicius Costa Gomes
[ Upstream commit e87ca16e99118ab4e130a41bdf12abbf6a87656c ] Change the "wait for operation finish" logic to take interrupts into account. When using dmatest with idxd DMA engine, it's possible that during longer tests, the interrupt notifying the finish of an operation happens during wait_event_freezable_timeout(), which causes dmatest to cleanup all the resources, some of which might still be in use. This fix ensures that the wait logic correctly handles interrupts, preventing premature cleanup of resources. Reported-by: kernel test robot <oliver.sang@intel.com> Closes: https://lore.kernel.org/oe-lkp/202502171134.8c403348-lkp@intel.com Signed-off-by: Vinicius Costa Gomes <vinicius.gomes@intel.com> Reviewed-by: Dave Jiang <dave.jiang@intel.com> Link: https://lore.kernel.org/r/20250305230007.590178-1-vinicius.gomes@intel.com Signed-off-by: Vinod Koul <vkoul@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
2025-05-02i3c: master: svc: Add support for Nuvoton npcm845 i3cStanley Chu
[ Upstream commit 98d87600a04e42282797631aa6b98dd43999e274 ] Nuvoton npcm845 SoC uses an older IP version, which has specific hardware issues that need to be addressed with a different compatible string. Add driver data for different compatible strings to define platform specific quirks. Add compatible string for npcm845 to define its own driver data. Signed-off-by: Stanley Chu <yschu@nuvoton.com> Reviewed-by: Frank Li <Frank.Li@nxp.com> Link: https://lore.kernel.org/r/20250306075429.2265183-3-yschu@nuvoton.com Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
2025-05-02xhci: Handle spurious events on Etron host isoc enpointsMathias Nyman
[ Upstream commit b331a3d8097fad4e541d212684192f21fedbd6e5 ] Unplugging a USB3.0 webcam from Etron hosts while streaming results in errors like this: [ 2.646387] xhci_hcd 0000:03:00.0: ERROR Transfer event TRB DMA ptr not part of current TD ep_index 18 comp_code 13 [ 2.646446] xhci_hcd 0000:03:00.0: Looking for event-dma 000000002fdf8630 trb-start 000000002fdf8640 trb-end 000000002fdf8650 [ 2.646560] xhci_hcd 0000:03:00.0: ERROR Transfer event TRB DMA ptr not part of current TD ep_index 18 comp_code 13 [ 2.646568] xhci_hcd 0000:03:00.0: Looking for event-dma 000000002fdf8660 trb-start 000000002fdf8670 trb-end 000000002fdf8670 Etron xHC generates two transfer events for the TRB if an error is detected while processing the last TRB of an isoc TD. The first event can be any sort of error (like USB Transaction or Babble Detected, etc), and the final event is Success. The xHCI driver will handle the TD after the first event and remove it from its internal list, and then print an "Transfer event TRB DMA ptr not part of current TD" error message after the final event. Commit 5372c65e1311 ("xhci: process isoc TD properly when there was a transaction error mid TD.") is designed to address isoc transaction errors, but unfortunately it doesn't account for this scenario. This issue is similar to the XHCI_SPURIOUS_SUCCESS case where a success event follows a 'short transfer' event, but the TD the event points to is already given back. Expand the spurious success 'short transfer' event handling to cover the spurious success after error on Etron hosts. Kuangyi Chiang reported this issue and submitted a different solution based on using error_mid_td. This commit message is mostly taken from that patch. Reported-by: Kuangyi Chiang <ki.chiang65@gmail.com> Closes: https://lore.kernel.org/linux-usb/20241028025337.6372-6-ki.chiang65@gmail.com/ Tested-by: Kuangyi Chiang <ki.chiang65@gmail.com> Tested-by: Michal Pecio <michal.pecio@gmail.com> Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com> Link: https://lore.kernel.org/r/20250306144954.3507700-16-mathias.nyman@linux.intel.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
2025-05-02usb: xhci: Fix isochronous Ring Underrun/Overrun event handlingMichal Pecio
[ Upstream commit 906dec15b9b321b546fd31a3c99ffc13724c7af4 ] The TRB pointer of these events points at enqueue at the time of error occurrence on xHCI 1.1+ HCs or it's NULL on older ones. By the time we are handling the event, a new TD may be queued at this ring position. I can trigger this race by rising interrupt moderation to increase IRQ handling delay. Similar delay may occur naturally due to system load. If this ever happens after a Missed Service Error, missed TDs will be skipped and the new TD processed as if it matched the event. It could be given back prematurely, risking data loss or buffer UAF by the xHC. Don't complete TDs on xrun events and don't warn if queued TDs don't match the event's TRB pointer, which can be NULL or a link/no-op TRB. Don't warn if there are no queued TDs at all. Now that it's safe, also handle xrun events if the skip flag is clear. This ensures completion of any TD stuck in 'error mid TD' state right before the xrun event, which could happen if a driver submits a finite number of URBs to a buggy HC and then an error occurs on the last TD. Signed-off-by: Michal Pecio <michal.pecio@gmail.com> Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com> Link: https://lore.kernel.org/r/20250306144954.3507700-6-mathias.nyman@linux.intel.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
2025-05-02usb: xhci: Complete 'error mid TD' transfers when handling Missed ServiceMichal Pecio
[ Upstream commit bfa8459942822bdcc86f0e87f237c0723ae64948 ] Missed Service Error after an error mid TD means that the failed TD has already been passed by the xHC without acknowledgment of the final TRB, a known hardware bug. So don't wait any more and give back the TD. Reproduced on NEC uPD720200 under conditions of ludicrously bad USB link quality, confirmed to behave as expected using dynamic debug. Signed-off-by: Michal Pecio <michal.pecio@gmail.com> Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com> Link: https://lore.kernel.org/r/20250306144954.3507700-5-mathias.nyman@linux.intel.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
2025-05-02usb: dwc3: gadget: Avoid using reserved endpoints on Intel MerrifieldAndy Shevchenko
[ Upstream commit 461f24bff86808ee5fbfe74751a825f8a7ab24e0 ] Intel Merrifield SoC uses these endpoints for tracing and they cannot be re-allocated if being used because the side band flow control signals are hard wired to certain endpoints: • 1 High BW Bulk IN (IN#1) (RTIT) • 1 1KB BW Bulk IN (IN#8) + 1 1KB BW Bulk OUT (Run Control) (OUT#8) In device mode, since RTIT (EP#1) and EXI/RunControl (EP#8) uses External Buffer Control (EBC) mode, these endpoints are to be mapped to EBC mode (to be done by EXI target driver). Additionally TRB for RTIT and EXI are maintained in STM (System Trace Module) unit and the EXI target driver will as well configure the TRB location for EP #1 IN and EP#8 (IN and OUT). Since STM/PTI and EXI hardware blocks manage these endpoints and interface to OTG3 controller through EBC interface, there is no need to enable any events (such as XferComplete etc) for these end points. Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com> Tested-by: Ferry Toth <fntoth@gmail.com> Acked-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com> Link: https://lore.kernel.org/r/20250212193116.2487289-5-andriy.shevchenko@linux.intel.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
2025-05-02usb: dwc3: gadget: Refactor loop to avoid NULL endpointsAndy Shevchenko
[ Upstream commit eafba0205426091354f050381c32ad1567c35844 ] Prepare the gadget driver to handle the reserved endpoints that will be not allocated at the initialisation time. While at it, add a warning where the NULL endpoint should never happen. Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com> Tested-by: Ferry Toth <fntoth@gmail.com> Acked-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com> Link: https://lore.kernel.org/r/20250212193116.2487289-3-andriy.shevchenko@linux.intel.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
2025-05-02usb: host: max3421-hcd: Add missing spi_device_id tableAlexander Stein
[ Upstream commit 41d5e3806cf589f658f92c75195095df0b66f66a ] "maxim,max3421" DT compatible is missing its SPI device ID entry, not allowing module autoloading and leading to the following message: "SPI driver max3421-hcd has no spi_device_id for maxim,max3421" Fix this by adding the spi_device_id table. Signed-off-by: Alexander Stein <alexander.stein@mailbox.org> Link: https://lore.kernel.org/r/20250128195114.56321-1-alexander.stein@mailbox.org Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
2025-05-02mailbox: pcc: Always clear the platform ack interrupt firstSudeep Holla
[ Upstream commit cf1338c0e02880cd235a4590eeb15e2039c873bc ] The PCC mailbox interrupt handler (pcc_mbox_irq()) currently checks for command completion flags and any error status before clearing the interrupt. The below sequence highlights an issue in the handling of PCC mailbox interrupts, specifically when dealing with doorbell notifications and acknowledgment between the OSPM and the platform where type3 and type4 channels are sharing the interrupt. ------------------------------------------------------------------------- | T | Platform Firmware | OSPM/Linux PCC driver | |---|---------------------------------|---------------------------------| | 1 | | Build message in shmem | | 2 | | Ring Type3 chan doorbell | | 3 | Receives the doorbell interrupt | | | 4 | Process the message from OSPM | | | 5 | Build response for the message | | | 6 | Ring Platform ACK interrupt on | | | | Type3 chan to OSPM | Received the interrupt | | 7 | Build Notification in Type4 Chan| | | 8 | | Start processing interrupt in | | | | pcc_mbox_irq() handler | | 9 | | Enter PCC handler for Type4 chan| |10 | | Check command complete cleared | |11 | | Read the notification | |12 | | Clear Platform ACK interrupt | | | No effect from the previous step yet as the Platform ACK | | | interrupt has not yet been triggered for this channel | |13 | Ring Platform ACK interrupt on | | | | Type4 chan to OSPM | | |14 | | Enter PCC handler for Type3 chan| |15 | | Command complete is set. | |16 | | Read the response. | |17 | | Clear Platform ACK interrupt | |18 | | Leave PCC handler for Type3 | |19 | | Leave pcc_mbox_irq() handler | |20 | | Re-enter pcc_mbox_irq() handler | |21 | | Enter PCC handler for Type4 chan| |22 | | Leave PCC handler for Type4 chan| |23 | | Enter PCC handler for Type3 chan| |24 | | Leave PCC handler for Type3 chan| |25 | | Leave pcc_mbox_irq() handler | ------------------------------------------------------------------------- The key issue occurs when OSPM tries to acknowledge platform ack interrupt for a notification which is ready to be read and processed but the interrupt itself is not yet triggered by the platform. This ineffective acknowledgment leads to an issue later in time where the interrupt remains pending as we exit the interrupt handler without clearing the platform ack interrupt as there is no pending response or notification. The interrupt acknowledgment order is incorrect. To resolve this issue, the platform acknowledgment interrupt should always be cleared before processing the interrupt for any notifications or response. Reported-by: Robbie King <robbiek@xsightlabs.com> Reviewed-by: Huisong Li <lihuisong@huawei.com> Tested-by: Huisong Li <lihuisong@huawei.com> Tested-by: Adam Young <admiyo@os.amperecomputing.com> Tested-by: Robbie King <robbiek@xsightlabs.com> Signed-off-by: Sudeep Holla <sudeep.holla@arm.com> Signed-off-by: Jassi Brar <jassisinghbrar@gmail.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
2025-05-02mailbox: pcc: Fix the possible race in updation of chan_in_use flagHuisong Li
[ Upstream commit 9779d45c749340ab461d595c1a4a664cb28f3007 ] The function mbox_chan_received_data() calls the Rx callback of the mailbox client driver. The callback might set chan_in_use flag from pcc_send_data(). This flag's status determines whether the PCC channel is in use. However, there is a potential race condition where chan_in_use is updated incorrectly due to concurrency between the interrupt handler (pcc_mbox_irq()) and the command sender(pcc_send_data()). The 'chan_in_use' flag of a channel is set to true after sending a command. And the flag of the new command may be cleared erroneous by the interrupt handler afer mbox_chan_received_data() returns, As a result, the interrupt being level triggered can't be cleared in pcc_mbox_irq() and it will be disabled after the number of handled times exceeds the specified value. The error log is as follows: | kunpeng_hccs HISI04B2:00: PCC command executed timeout! | kunpeng_hccs HISI04B2:00: get port link status info failed, ret = -110 | irq 13: nobody cared (try booting with the "irqpoll" option) | Call trace: | dump_backtrace+0x0/0x210 | show_stack+0x1c/0x2c | dump_stack+0xec/0x130 | __report_bad_irq+0x50/0x190 | note_interrupt+0x1e4/0x260 | handle_irq_event+0x144/0x17c | handle_fasteoi_irq+0xd0/0x240 | __handle_domain_irq+0x80/0xf0 | gic_handle_irq+0x74/0x2d0 | el1_irq+0xbc/0x140 | mnt_clone_write+0x0/0x70 | file_update_time+0xcc/0x160 | fault_dirty_shared_page+0xe8/0x150 | do_shared_fault+0x80/0x1d0 | do_fault+0x118/0x1a4 | handle_pte_fault+0x154/0x230 | __handle_mm_fault+0x1ac/0x390 | handle_mm_fault+0xf0/0x250 | do_page_fault+0x184/0x454 | do_translation_fault+0xac/0xd4 | do_mem_abort+0x44/0xb4 | el0_da+0x40/0x74 | el0_sync_handler+0x60/0xb4 | el0_sync+0x168/0x180 | handlers: | pcc_mbox_irq | Disabling IRQ #13 To solve this issue, pcc_mbox_irq() must clear 'chan_in_use' flag before the call to mbox_chan_received_data(). Tested-by: Adam Young <admiyo@os.amperecomputing.com> Tested-by: Robbie King <robbiek@xsightlabs.com> Signed-off-by: Huisong Li <lihuisong@huawei.com> (sudeep.holla: Minor updates to the subject, commit message and comment) Signed-off-by: Sudeep Holla <sudeep.holla@arm.com> Signed-off-by: Jassi Brar <jassisinghbrar@gmail.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
2025-05-02s390/tty: Fix a potential memory leak bugHaoxiang Li
[ Upstream commit ad9bb8f049717d64c5e62b2a44954be9f681c65b ] The check for get_zeroed_page() leads to a direct return and overlooked the memory leak caused by loop allocation. Add a free helper to free spaces allocated by get_zeroed_page(). Signed-off-by: Haoxiang Li <haoxiang_li2024@163.com> Acked-by: Heiko Carstens <hca@linux.ibm.com> Link: https://lore.kernel.org/r/20250218034104.2436469-1-haoxiang_li2024@163.com Signed-off-by: Vasily Gorbik <gor@linux.ibm.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
2025-05-02s390/sclp: Add check for get_zeroed_page()Haoxiang Li
[ Upstream commit 3db42c75a921854a99db0a2775814fef97415bac ] Add check for the return value of get_zeroed_page() in sclp_console_init() to prevent null pointer dereference. Furthermore, to solve the memory leak caused by the loop allocation, add a free helper to do the free job. Signed-off-by: Haoxiang Li <haoxiang_li2024@163.com> Acked-by: Heiko Carstens <hca@linux.ibm.com> Link: https://lore.kernel.org/r/20250218025216.2421548-1-haoxiang_li2024@163.com Signed-off-by: Vasily Gorbik <gor@linux.ibm.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
2025-05-02clk: check for disabled clock-provider in of_clk_get_hw_from_clkspec()Heiko Stuebner
[ Upstream commit b20150d499b3ee5c2d632fbc5ac94f98dd33accf ] of_clk_get_hw_from_clkspec() checks all available clock-providers by comparing their of nodes to the one from the clkspec. If no matching clock provider is found, the function returns -EPROBE_DEFER to cause a re-check at a later date. If a matching clock provider is found, an authoritative answer can be retrieved from it whether the clock exists or not. This does not take into account that the clock-provider may never appear, because it's node is disabled. This can happen when a clock is optional, provided by a separate block which never gets enabled. One example of this happening is the rk3588's VOP, which has optional additional display clocks coming from PLLs inside the hdmiphy blocks. These can be used for better rates, but the system will also work without them. The problem around that is described in the followups to[1]. As we already know the of node of the presumed clock provider, add a check via of_device_is_available() whether this is a "valid" device node. This prevents eternal defer loops. Link: https://lore.kernel.org/dri-devel/20250215-vop2-hdmi1-disp-modes-v1-3-81962a7151d6@collabora.com/ [1] Reviewed-by: Sebastian Reichel <sebastian.reichel@collabora.com> Tested-by: Cristian Ciocaltea <cristian.ciocaltea@collabora.com> Signed-off-by: Heiko Stuebner <heiko@sntech.de> Link: https://lore.kernel.org/r/20250222223733.2990179-1-heiko@sntech.de [sboyd@kernel.org: Reword commit text a bit] Signed-off-by: Stephen Boyd <sboyd@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
2025-05-02crypto: ccp - Add support for PCI device 0x1134Devaraj Rangasamy
[ Upstream commit 6cb345939b8cc4be79909875276aa9dc87d16757 ] PCI device 0x1134 shares same register features as PCI device 0x17E0. Hence reuse same data for the new PCI device ID 0x1134. Signed-off-by: Devaraj Rangasamy <Devaraj.Rangasamy@amd.com> Acked-by: Tom Lendacky <thomas.lendacky@amd.com> Reviewed-by: Mario Limonciello <mario.limonciello@amd.com> Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au> Signed-off-by: Sasha Levin <sashal@kernel.org>
2025-05-02pinctrl: mcp23s08: Get rid of spurious level interruptsDmitry Mastykin
[ Upstream commit 7b0671b97f0872d6950ccc925e210cb3f67721bf ] irq_mask()/irq_unmask() are not called for nested interrupts. So level interrupts are never masked, chip's interrupt output is not cleared on INTCAP or GPIO read, the irq handler is uselessly called again. Nested irq handler is not called again, because interrupt reason is cleared by its first call. /proc/interrupts shows that number of chip's irqs is greater than number of nested irqs. This patch adds masking and unmasking level interrupts inside irq handler. Signed-off-by: Dmitry Mastykin <mastichi@gmail.com> Link: https://lore.kernel.org/20250122120504.1279790-1-mastichi@gmail.com Signed-off-by: Linus Walleij <linus.walleij@linaro.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
2025-05-02pinctrl: renesas: rza2: Fix potential NULL pointer dereferenceChenyuan Yang
[ Upstream commit f752ee5b5b86b5f88a5687c9eb0ef9b39859b908 ] `chip.label` in rza2_gpio_register() could be NULL. Add the missing check. Signed-off-by: Chenyuan Yang <chenyuan0y@gmail.com> Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be> Reviewed-by: Matthias Brugger <matthias.bgg@gmail.com> Link: https://lore.kernel.org/20250210232552.1545887-1-chenyuan0y@gmail.com Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be> Signed-off-by: Sasha Levin <sashal@kernel.org>
2025-05-02USB: wdm: add annotationOliver Neukum
commit 73e9cc1ffd3650b12c4eb059dfdafd56e725ceda upstream. This is not understandable without a comment on endianness Fixes: afba937e540c9 ("USB: CDC WDM driver") Cc: stable <stable@kernel.org> Signed-off-by: Oliver Neukum <oneukum@suse.com> Link: https://lore.kernel.org/r/20250401084749.175246-5-oneukum@suse.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2025-05-02USB: wdm: wdm_wwan_port_tx_complete mutex in atomic contextOliver Neukum
commit 1fdc4dca350c0b8ada0b8ebf212504e1ad55e511 upstream. wdm_wwan_port_tx_complete is called from a completion handler with irqs disabled and possible in IRQ context usb_autopm_put_interface can take a mutex. Hence usb_autopm_put_interface_async must be used. Fixes: cac6fb015f71 ("usb: class: cdc-wdm: WWAN framework integration") Cc: stable <stable@kernel.org> Signed-off-by: Oliver Neukum <oneukum@suse.com> Link: https://lore.kernel.org/r/20250401084749.175246-4-oneukum@suse.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2025-05-02USB: wdm: close race between wdm_open and wdm_wwan_port_stopOliver Neukum
commit c1846ed4eb527bdfe6b3b7dd2c78e2af4bf98f4f upstream. Clearing WDM_WWAN_IN_USE must be the last action or we can open a chardev whose URBs are still poisoned Fixes: cac6fb015f71 ("usb: class: cdc-wdm: WWAN framework integration") Cc: stable <stable@kernel.org> Signed-off-by: Oliver Neukum <oneukum@suse.com> Link: https://lore.kernel.org/r/20250401084749.175246-3-oneukum@suse.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2025-05-02USB: wdm: handle IO errors in wdm_wwan_port_startOliver Neukum
commit 9697f5efcf5fdea65b8390b5eb81bebe746ceedc upstream. In case submitting the URB fails we must undo what we've done so far. Fixes: cac6fb015f71 ("usb: class: cdc-wdm: WWAN framework integration") Cc: stable <stable@kernel.org> Signed-off-by: Oliver Neukum <oneukum@suse.com> Link: https://lore.kernel.org/r/20250401084749.175246-2-oneukum@suse.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2025-05-02USB: VLI disk crashes if LPM is usedOliver Neukum
commit e00b39a4f3552c730f1e24c8d62c4a8c6aad4e5d upstream. This device needs the NO_LPM quirk. Cc: stable <stable@kernel.org> Signed-off-by: Oliver Neukum <oneukum@suse.com> Link: https://lore.kernel.org/r/20250408135800.792515-1-oneukum@suse.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2025-05-02usb: quirks: Add delay init quirk for SanDisk 3.2Gen1 Flash DriveMiao Li
commit 37ffdbd695c02189dbf23d6e7d2385e0299587ca upstream. The SanDisk 3.2Gen1 Flash Drive, which VID:PID is in 0781:55a3, just like Silicon Motion Flash Drive: https://lore.kernel.org/r/20250401023027.44894-1-limiao870622@163.com also needs the DELAY_INIT quirk, or it will randomly work incorrectly (e.g.: lsusb and can't list this device info) when connecting Huawei hisi platforms and doing thousand of reboot test circles. Cc: stable <stable@kernel.org> Signed-off-by: Miao Li <limiao@kylinos.cn> Signed-off-by: Lei Huang <huanglei@kylinos.cn> Link: https://lore.kernel.org/r/20250414062935.159024-1-limiao870622@163.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2025-05-02usb: quirks: add DELAY_INIT quirk for Silicon Motion Flash DriveMiao Li
commit 2932b6b547ec36ad2ed60fbf2117c0e46bb7d40a upstream. Silicon Motion Flash Drive connects to Huawei hisi platforms and performs a system reboot test for two thousand circles, it will randomly work incorrectly on boot, set DELAY_INIT quirk can workaround this issue. Signed-off-by: Miao Li <limiao@kylinos.cn> Cc: stable <stable@kernel.org> Link: https://lore.kernel.org/r/20250401023027.44894-1-limiao870622@163.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2025-05-02usb: dwc3: xilinx: Prevent spike in reset signalMike Looijmans
commit 38d6e60b6f3a99f8f13bee22eab616136c2c0675 upstream. The "reset" GPIO controls the RESET signal to an external, usually ULPI PHY, chip. The original code path acquires the signal in LOW state, and then immediately asserts it HIGH again, if the reset signal defaulted to asserted, there'd be a short "spike" before the reset. Here is what happens depending on the pre-existing state of the reset signal: Reset (previously asserted): ~~~|_|~~~~|_______ Reset (previously deasserted): _____|~~~~|_______ ^ ^ ^ A B C At point A, the low going transition is because the reset line is requested using GPIOD_OUT_LOW. If the line is successfully requested, the first thing we do is set it high _without_ any delay. This is point B. So, a glitch occurs between A and B. Requesting the line using GPIOD_OUT_HIGH eliminates the A and B transitions. Instead we get: Reset (previously asserted) : ~~~~~~~~~~|______ Reset (previously deasserted): ____|~~~~~|______ ^ ^ A C Where A and C are the points described above in the code. Point B has been eliminated. The issue was found during code inspection. Also remove the cryptic "toggle ulpi .." comment. Fixes: ca05b38252d7 ("usb: dwc3: xilinx: Add gpio-reset support") Cc: stable <stable@kernel.org> Signed-off-by: Mike Looijmans <mike.looijmans@topic.nl> Reviewed-by: Radhey Shyam Pandey <radhey.shyam.pandey@amd.com> Acked-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com> Link: https://lore.kernel.org/r/20250318064518.9320-1-mike.looijmans@topic.nl Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2025-05-02usb: dwc3: gadget: check that event count does not exceed event buffer lengthFrode Isaksen
commit 63ccd26cd1f6600421795f6ca3e625076be06c9f upstream. The event count is read from register DWC3_GEVNTCOUNT. There is a check for the count being zero, but not for exceeding the event buffer length. Check that event count does not exceed event buffer length, avoiding an out-of-bounds access when memcpy'ing the event. Crash log: Unable to handle kernel paging request at virtual address ffffffc0129be000 pc : __memcpy+0x114/0x180 lr : dwc3_check_event_buf+0xec/0x348 x3 : 0000000000000030 x2 : 000000000000dfc4 x1 : ffffffc0129be000 x0 : ffffff87aad60080 Call trace: __memcpy+0x114/0x180 dwc3_interrupt+0x24/0x34 Signed-off-by: Frode Isaksen <frode@meta.com> Fixes: 72246da40f37 ("usb: Introduce DesignWare USB3 DRD Driver") Cc: stable <stable@kernel.org> Acked-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com> Link: https://lore.kernel.org/r/20250403072907.448524-1-fisaksen@baylibre.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2025-05-02USB: OHCI: Add quirk for LS7A OHCI controller (rev 0x02)Huacai Chen
commit bcb60d438547355b8f9ad48645909139b64d3482 upstream. The OHCI controller (rev 0x02) under LS7A PCI host has a hardware flaw. MMIO register with offset 0x60/0x64 is treated as legacy PS2-compatible keyboard/mouse interface, which confuse the OHCI controller. Since OHCI only use a 4KB BAR resource indeed, the LS7A OHCI controller's 32KB BAR is wrapped around (the second 4KB BAR space is the same as the first 4KB internally). So we can add an 4KB offset (0x1000) to the OHCI registers (from the PCI BAR resource) as a quirk. Cc: stable <stable@kernel.org> Suggested-by: Bjorn Helgaas <bhelgaas@google.com> Reviewed-by: Alan Stern <stern@rowland.harvard.edu> Tested-by: Mingcong Bai <baimingcong@loongson.cn> Signed-off-by: Huacai Chen <chenhuacai@loongson.cn> Link: https://lore.kernel.org/r/20250328040059.3672979-1-chenhuacai@loongson.cn Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2025-05-02usb: chipidea: ci_hdrc_imx: implement usb_phy_init() error handlingFedor Pchelkin
commit 8c531e0a8c2d82509ad97c6d3a1e6217c7ed136d upstream. usb_phy_init() may return an error code if e.g. its implementation fails to prepare/enable some clocks. And properly rollback on probe error path by calling the counterpart usb_phy_shutdown(). Found by Linux Verification Center (linuxtesting.org). Fixes: be9cae2479f4 ("usb: chipidea: imx: Fix ULPI on imx53") Cc: stable <stable@kernel.org> Signed-off-by: Fedor Pchelkin <pchelkin@ispras.ru> Acked-by: Peter Chen <peter.chen@kernel.org> Link: https://lore.kernel.org/r/20250316102658.490340-4-pchelkin@ispras.ru Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2025-05-02usb: chipidea: ci_hdrc_imx: fix call balance of regulator routinesFedor Pchelkin
commit 8cab0e9a3f3e8d700179e0d6141643d54a267fd5 upstream. Upon encountering errors during the HSIC pinctrl handling section the regulator should be disabled. Use devm_add_action_or_reset() to let the regulator-disabling routine be handled by device resource management stack. Found by Linux Verification Center (linuxtesting.org). Fixes: 4d6141288c33 ("usb: chipidea: imx: pinctrl for HSIC is optional") Cc: stable <stable@kernel.org> Signed-off-by: Fedor Pchelkin <pchelkin@ispras.ru> Acked-by: Peter Chen <peter.chen@kernel.org> Link: https://lore.kernel.org/r/20250316102658.490340-3-pchelkin@ispras.ru Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2025-05-02usb: chipidea: ci_hdrc_imx: fix usbmisc handlingFedor Pchelkin
commit 4e28f79e3dffa52d327b46d1a78dac16efb5810b upstream. usbmisc is an optional device property so it is totally valid for the corresponding data->usbmisc_data to have a NULL value. Check that before dereferencing the pointer. Found by Linux Verification Center (linuxtesting.org) with Svace static analysis tool. Fixes: 74adad500346 ("usb: chipidea: ci_hdrc_imx: decrement device's refcount in .remove() and in the error path of .probe()") Cc: stable <stable@kernel.org> Signed-off-by: Fedor Pchelkin <pchelkin@ispras.ru> Acked-by: Peter Chen <peter.chen@kernel.org> Link: https://lore.kernel.org/r/20250316102658.490340-2-pchelkin@ispras.ru Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2025-05-02usb: cdns3: Fix deadlock when using NCM gadgetRalph Siemsen
commit a1059896f2bfdcebcdc7153c3be2307ea319501f upstream. The cdns3 driver has the same NCM deadlock as fixed in cdnsp by commit 58f2fcb3a845 ("usb: cdnsp: Fix deadlock issue during using NCM gadget"). Under PREEMPT_RT the deadlock can be readily triggered by heavy network traffic, for example using "iperf --bidir" over NCM ethernet link. The deadlock occurs because the threaded interrupt handler gets preempted by a softirq, but both are protected by the same spinlock. Prevent deadlock by disabling softirq during threaded irq handler. Cc: stable <stable@kernel.org> Fixes: 7733f6c32e36 ("usb: cdns3: Add Cadence USB3 DRD Driver") Signed-off-by: Ralph Siemsen <ralph.siemsen@linaro.org> Acked-by: Peter Chen <peter.chen@kernel.org> Reviewed-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de> Link: https://lore.kernel.org/r/20250318-rfs-cdns3-deadlock-v2-1-bfd9cfcee732@linaro.org Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2025-05-02usb: xhci: Fix invalid pointer dereference in Etron workaroundMichal Pecio
commit 1ea050da5562af9b930d17cbbe9632d30f5df43a upstream. This check is performed before prepare_transfer() and prepare_ring(), so enqueue can already point at the final link TRB of a segment. And indeed it will, some 0.4% of times this code is called. Then enqueue + 1 is an invalid pointer. It will crash the kernel right away or load some junk which may look like a link TRB and cause the real link TRB to be replaced with a NOOP. This wouldn't end well. Use a functionally equivalent test which doesn't dereference the pointer and always gives correct result. Something has crashed my machine twice in recent days while playing with an Etron HC, and a control transfer stress test ran for confirmation has just crashed it again. The same test passes with this patch applied. Fixes: 5e1c67abc930 ("xhci: Fix control transfer error on Etron xHCI host") Cc: stable@vger.kernel.org Signed-off-by: Michal Pecio <michal.pecio@gmail.com> Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com> Reviewed-by: Kuangyi Chiang <ki.chiang65@gmail.com> Link: https://lore.kernel.org/r/20250410151828.2868740-5-mathias.nyman@linux.intel.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2025-05-02xhci: Limit time spent with xHC interrupts disabled during bus resumeMathias Nyman
commit bea5892d0ed274e03655223d1977cf59f9aff2f2 upstream. Current xhci bus resume implementation prevents xHC host from generating interrupts during high-speed USB 2 and super-speed USB 3 bus resume. Only reason to disable interrupts during bus resume would be to prevent the interrupt handler from interfering with the resume process of USB 2 ports. Host initiated resume of USB 2 ports is done in two stages. The xhci driver first transitions the port from 'U3' to 'Resume' state, then wait in Resume for 20ms, and finally moves port to U0 state. xhci driver can't prevent interrupts by keeping the xhci spinlock due to this 20ms sleep. Limit interrupt disabling to the USB 2 port resume case only. resuming USB 2 ports in bus resume is only done in special cases where USB 2 ports had to be forced to suspend during bus suspend. The current way of preventing interrupts by clearing the 'Interrupt Enable' (INTE) bit in USBCMD register won't prevent the Interrupter registers 'Interrupt Pending' (IP), 'Event Handler Busy' (EHB) and USBSTS register Event Interrupt (EINT) bits from being set. New interrupts can't be issued before those bits are properly clered. Disable interrupts by clearing the interrupter register 'Interrupt Enable' (IE) bit instead. This way IP, EHB and INTE won't be set before IE is enabled again and a new interrupt is triggered. Reported-by: Devyn Liu <liudingyuan@huawei.com> Closes: https://lore.kernel.org/linux-usb/b1a9e2d51b4d4ff7a304f77c5be8164e@huawei.com/ Cc: stable@vger.kernel.org Tested-by: Devyn Liu <liudingyuan@huawei.com> Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com> Link: https://lore.kernel.org/r/20250410151828.2868740-6-mathias.nyman@linux.intel.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2025-05-02USB: serial: simple: add OWON HDS200 series oscilloscope supportCraig Hesling
commit 4cc01410e1c1dd075df10f750775c81d1cb6672b upstream. Add serial support for OWON HDS200 series oscilloscopes and likely many other pieces of OWON test equipment. OWON HDS200 series devices host two USB endpoints, designed to facilitate bidirectional SCPI. SCPI is a predominately ASCII text protocol for test/measurement equipment. Having a serial/tty interface for these devices lowers the barrier to entry for anyone trying to write programs to communicate with them. The following shows the USB descriptor for the OWON HDS272S running firmware V5.7.1: Bus 001 Device 068: ID 5345:1234 Owon PDS6062T Oscilloscope Negotiated speed: Full Speed (12Mbps) Device Descriptor: bLength 18 bDescriptorType 1 bcdUSB 2.00 bDeviceClass 0 [unknown] bDeviceSubClass 0 [unknown] bDeviceProtocol 0 bMaxPacketSize0 64 idVendor 0x5345 Owon idProduct 0x1234 PDS6062T Oscilloscope bcdDevice 1.00 iManufacturer 1 oscilloscope iProduct 2 oscilloscope iSerial 3 oscilloscope bNumConfigurations 1 Configuration Descriptor: bLength 9 bDescriptorType 2 wTotalLength 0x0029 bNumInterfaces 1 bConfigurationValue 1 iConfiguration 0 bmAttributes 0x80 (Bus Powered) MaxPower 100mA Interface Descriptor: bLength 9 bDescriptorType 4 bInterfaceNumber 0 bAlternateSetting 0 bNumEndpoints 2 bInterfaceClass 5 Physical Interface Device bInterfaceSubClass 0 [unknown] bInterfaceProtocol 0 iInterface 0 ** UNRECOGNIZED: 09 21 11 01 00 01 22 5f 00 Endpoint Descriptor: bLength 7 bDescriptorType 5 bEndpointAddress 0x81 EP 1 IN bmAttributes 2 Transfer Type Bulk Synch Type None Usage Type Data wMaxPacketSize 0x0040 1x 64 bytes bInterval 32 Endpoint Descriptor: bLength 7 bDescriptorType 5 bEndpointAddress 0x01 EP 1 OUT bmAttributes 2 Transfer Type Bulk Synch Type None Usage Type Data wMaxPacketSize 0x0040 1x 64 bytes bInterval 32 Device Status: 0x0000 (Bus Powered) OWON appears to be using the same USB Vendor and Product ID for many of their oscilloscopes. Looking at the discussion about the USB vendor/product ID, in the link bellow, suggests that this VID/PID is shared with VDS, SDS, PDS, and now the HDS series oscilloscopes. Available documentation for these devices seems to indicate that all use a similar SCPI protocol, some with RS232 options. It is likely that this same simple serial setup would work correctly for them all. Link: https://usb-ids.gowdy.us/read/UD/5345/1234 Signed-off-by: Craig Hesling <craig@hesling.com> Cc: stable@vger.kernel.org Signed-off-by: Johan Hovold <johan@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2025-05-02USB: serial: option: add Sierra Wireless EM9291Adam Xue
commit 968e1cbb1f6293c3add9607f80b5ce3d29f57583 upstream. Add Sierra Wireless EM9291. Interface 0: MBIM control 1: MBIM data 3: AT port 4: Diagnostic port T: Bus=01 Lev=01 Prnt=01 Port=00 Cnt=01 Dev#= 2 Spd=480 MxCh= 0 D: Ver= 2.10 Cls=00(>ifc ) Sub=00 Prot=00 MxPS=64 #Cfgs= 1 P: Vendor=1199 ProdID=90e3 Rev=00.06 S: Manufacturer=Sierra Wireless, Incorporated S: Product=Sierra Wireless EM9291 S: SerialNumber=xxxxxxxxxxxxxxxx C: #Ifs= 4 Cfg#= 1 Atr=a0 MxPwr=500mA I: If#= 0 Alt= 0 #EPs= 1 Cls=02(commc) Sub=0e Prot=00 Driver=cdc_mbim E: Ad=81(I) Atr=03(Int.) MxPS= 64 Ivl=32ms I: If#= 1 Alt= 1 #EPs= 2 Cls=0a(data ) Sub=00 Prot=02 Driver=cdc_mbim E: Ad=0f(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms E: Ad=8e(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms I: If#= 3 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=ff Prot=40 Driver=(none) E: Ad=01(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms E: Ad=82(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms E: Ad=83(I) Atr=03(Int.) MxPS= 10 Ivl=32ms I: If#= 4 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=30 Driver=(none) E: Ad=02(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms E: Ad=84(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms Signed-off-by: Adam Xue <zxue@semtech.com> Cc: stable@vger.kernel.org Signed-off-by: Johan Hovold <johan@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2025-05-02USB: serial: ftdi_sio: add support for Abacus Electrics Optical ProbeMichael Ehrenreich
commit b399078f882b6e5d32da18b6c696cc84b12f90d5 upstream. Abacus Electrics makes optical probes for interacting with smart meters over an optical interface. At least one version uses an FT232B chip (as detected by ftdi_sio) with a custom USB PID, which needs to be added to the list to make the device work in a plug-and-play fashion. Signed-off-by: Michael Ehrenreich <michideep@gmail.com> Cc: stable@vger.kernel.org Signed-off-by: Johan Hovold <johan@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2025-05-02serial: sifive: lock port in startup()/shutdown() callbacksRyo Takakura
commit e1ca3ff28ab1e2c1e70713ef3fa7943c725742c3 upstream. startup()/shutdown() callbacks access SIFIVE_SERIAL_IE_OFFS. The register is also accessed from write() callback. If console were printing and startup()/shutdown() callback gets called, its access to the register could be overwritten. Add port->lock to startup()/shutdown() callbacks to make sure their access to SIFIVE_SERIAL_IE_OFFS is synchronized against write() callback. Fixes: 45c054d0815b ("tty: serial: add driver for the SiFive UART") Signed-off-by: Ryo Takakura <ryotkkr98@gmail.com> Reviewed-by: Petr Mladek <pmladek@suse.com> Cc: stable@vger.kernel.org Reviewed-by: John Ogness <john.ogness@linutronix.de> Rule: add Link: https://lore.kernel.org/stable/20250330003522.386632-1-ryotkkr98%40gmail.com Link: https://lore.kernel.org/r/20250412001847.183221-1-ryotkkr98@gmail.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2025-05-02serial: msm: Configure correct working mode before starting earlyconStephan Gerhold
commit 7094832b5ac861b0bd7ed8866c93cb15ef619996 upstream. The MSM UART DM controller supports different working modes, e.g. DMA or the "single-character mode", where all reads/writes operate on a single character rather than 4 chars (32-bit) at once. When using earlycon, __msm_console_write() always writes 4 characters at a time, but we don't know which mode the bootloader was using and we don't set the mode either. This causes garbled output if the bootloader was using the single-character mode, because only every 4th character appears in the serial console, e.g. "[ 00oni pi 000xf0[ 00i s 5rm9(l)l s 1 1 SPMTA 7:C 5[ 00A ade k d[ 00ano:ameoi .Q1B[ 00ac _idaM00080oo'" If the bootloader was using the DMA ("DM") mode, output would likely fail entirely. Later, when the full serial driver probes, the port is re-initialized and output works as expected. Fix this also for earlycon by clearing the DMEN register and reset+re-enable the transmitter to apply the change. This ensures the transmitter is in the expected state before writing any output. Cc: stable <stable@kernel.org> Fixes: 0efe72963409 ("tty: serial: msm: Add earlycon support") Signed-off-by: Stephan Gerhold <stephan.gerhold@linaro.org> Reviewed-by: Neil Armstrong <neil.armstrong@linaro.org> Link: https://lore.kernel.org/r/20250408-msm-serial-earlycon-v1-1-429080127530@linaro.org Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2025-05-02tty: Require CAP_SYS_ADMIN for all usages of TIOCL_SELMOUSEREPORTGünther Noack
commit ee6a44da3c87cf64d67dd02be8c0127a5bf56175 upstream. This requirement was overeagerly loosened in commit 2f83e38a095f ("tty: Permit some TIOCL_SETSEL modes without CAP_SYS_ADMIN"), but as it turns out, (1) the logic I implemented there was inconsistent (apologies!), (2) TIOCL_SELMOUSEREPORT might actually be a small security risk after all, and (3) TIOCL_SELMOUSEREPORT is only meant to be used by the mouse daemon (GPM or Consolation), which runs as CAP_SYS_ADMIN already. In more detail: 1. The previous patch has inconsistent logic: In commit 2f83e38a095f ("tty: Permit some TIOCL_SETSEL modes without CAP_SYS_ADMIN"), we checked for sel_mode == TIOCL_SELMOUSEREPORT, but overlooked that the lower four bits of this "mode" parameter were actually used as an additional way to pass an argument. So the patch did actually still require CAP_SYS_ADMIN, if any of the mouse button bits are set, but did not require it if none of the mouse buttons bits are set. This logic is inconsistent and was not intentional. We should have the same policies for using TIOCL_SELMOUSEREPORT independent of the value of the "hidden" mouse button argument. I sent a separate documentation patch to the man page list with more details on TIOCL_SELMOUSEREPORT: https://lore.kernel.org/all/20250223091342.35523-2-gnoack3000@gmail.com/ 2. TIOCL_SELMOUSEREPORT is indeed a potential security risk which can let an attacker simulate "keyboard" input to command line applications on the same terminal, like TIOCSTI and some other TIOCLINUX "selection mode" IOCTLs. By enabling mouse reporting on a terminal and then injecting mouse reports through TIOCL_SELMOUSEREPORT, an attacker can simulate mouse movements on the same terminal, similar to the TIOCSTI keystroke injection attacks that were previously possible with TIOCSTI and other TIOCL_SETSEL selection modes. Many programs (including libreadline/bash) are then prone to misinterpret these mouse reports as normal keyboard input because they do not expect input in the X11 mouse protocol form. The attacker does not have complete control over the escape sequence, but they can at least control the values of two consecutive bytes in the binary mouse reporting escape sequence. I went into more detail on that in the discussion at https://lore.kernel.org/all/20250221.0a947528d8f3@gnoack.org/ It is not equally trivial to simulate arbitrary keystrokes as it was with TIOCSTI (commit 83efeeeb3d04 ("tty: Allow TIOCSTI to be disabled")), but the general mechanism is there, and together with the small number of existing legit use cases (see below), it would be better to revert back to requiring CAP_SYS_ADMIN for TIOCL_SELMOUSEREPORT, as it was already the case before commit 2f83e38a095f ("tty: Permit some TIOCL_SETSEL modes without CAP_SYS_ADMIN"). 3. TIOCL_SELMOUSEREPORT is only used by the mouse daemons (GPM or Consolation), and they are the only legit use case: To quote console_codes(4): The mouse tracking facility is intended to return xterm(1)-compatible mouse status reports. Because the console driver has no way to know the device or type of the mouse, these reports are returned in the console input stream only when the virtual terminal driver receives a mouse update ioctl. These ioctls must be generated by a mouse-aware user-mode application such as the gpm(8) daemon. Jared Finder has also confirmed in https://lore.kernel.org/all/491f3df9de6593df8e70dbe77614b026@finder.org/ that Emacs does not call TIOCL_SELMOUSEREPORT directly, and it would be difficult to find good reasons for doing that, given that it would interfere with the reports that GPM is sending. More information on the interaction between GPM, terminals and the kernel with additional pointers is also available in this patch: https://lore.kernel.org/all/a773e48920aa104a65073671effbdee665c105fc.1603963593.git.tammo.block@gmail.com/ For background on who else uses TIOCL_SELMOUSEREPORT: Debian Code search finds one page of results, the only two known callers are the two mouse daemons GPM and Consolation. (GPM does not show up in the search results because it uses literal numbers to refer to TIOCLINUX-related enums. I looked through GPM by hand instead. TIOCL_SELMOUSEREPORT is also not used from libgpm.) https://codesearch.debian.net/search?q=TIOCL_SELMOUSEREPORT Cc: Jared Finder <jared@finder.org> Cc: Jann Horn <jannh@google.com> Cc: Hanno Böck <hanno@hboeck.de> Cc: Jiri Slaby <jirislaby@kernel.org> Cc: Kees Cook <kees@kernel.org> Cc: stable <stable@kernel.org> Fixes: 2f83e38a095f ("tty: Permit some TIOCL_SETSEL modes without CAP_SYS_ADMIN") Signed-off-by: Günther Noack <gnoack3000@gmail.com> Link: https://lore.kernel.org/r/20250411070144.3959-2-gnoack3000@gmail.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
generated by cgit v1.2.3 (git 2.39.1) at 2025-08-04 07:22:20 +0000