| Age | Commit message (Collapse) | Author |
|---|
|
Although it seems unlikely in practice - there would need to be
rx ring indexes greater than 10^10 - it is theoretically possible
for the filename of per rx ring debugfs files to be truncated.
This is because although a 16 byte buffer is provided, the length
of the filename is restricted to 10 bytes. Remove this restriction
and allow the entire buffer to be used.
Also reduce the buffer to 12 bytes, which is sufficient.
Given that the range of rx ring indexes likely much smaller than the
maximum range of a 32-bit signed integer, a smaller buffer could be
used, with some further changes. But this change seems simple, robust,
and has minimal stack overhead.
Flagged by gcc-14:
.../bnxt_debugfs.c: In function 'bnxt_debug_dev_init':
drivers/net/ethernet/broadcom/bnxt/bnxt_debugfs.c:69:30: warning: '%d' directive output may be truncated writing between 1 and 11 bytes into a region of size 10 [-Wformat-truncation=]
69 | snprintf(qname, 10, "%d", ring_idx);
| ^~
In function 'debugfs_dim_ring_init',
inlined from 'bnxt_debug_dev_init' at .../bnxt_debugfs.c:87:4:
.../bnxt_debugfs.c:69:29: note: directive argument in the range [-2147483643, 2147483646]
69 | snprintf(qname, 10, "%d", ring_idx);
| ^~~~
.../bnxt_debugfs.c:69:9: note: 'snprintf' output between 2 and 12 bytes into a destination of size 10
69 | snprintf(qname, 10, "%d", ring_idx);
| ^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
Compile tested only
Signed-off-by: Simon Horman <horms@kernel.org>
Reviewed-by: Michael Chan <michael.chan@broadcom.com>
Link: https://patch.msgid.link/20240813-bnxt-str-v2-2-872050a157e7@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
This corrects an out-by-one error in the maximum length of the package
version string. The size argument of snprintf includes space for the
trailing '\0' byte, so there is no need to allow extra space for it by
reducing the value of the size argument by 1.
Found by inspection.
Compile tested only.
Signed-off-by: Simon Horman <horms@kernel.org>
Reviewed-by: Michael Chan <michael.chan@broadcom.com>
Link: https://patch.msgid.link/20240813-bnxt-str-v2-1-872050a157e7@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
This reverts commit 28ab9769117ca944cb6eb537af5599aa436287a4.
Sense data can be in either fixed format or descriptor format.
SAT-6 revision 1, "10.4.6 Control mode page", defines the D_SENSE bit:
"The SATL shall support this bit as defined in SPC-5 with the following
exception: if the D_ SENSE bit is set to zero (i.e., fixed format sense
data), then the SATL should return fixed format sense data for ATA
PASS-THROUGH commands."
The libata SATL has always kept D_SENSE set to zero by default. (It is
however possible to change the value using a MODE SELECT SG_IO command.)
Failed ATA PASS-THROUGH commands correctly respected the D_SENSE bit,
however, successful ATA PASS-THROUGH commands incorrectly returned the
sense data in descriptor format (regardless of the D_SENSE bit).
Commit 28ab9769117c ("ata: libata-scsi: Honor the D_SENSE bit for
CK_COND=1 and no error") fixed this bug for successful ATA PASS-THROUGH
commands.
However, after commit 28ab9769117c ("ata: libata-scsi: Honor the D_SENSE
bit for CK_COND=1 and no error"), there were bug reports that hdparm,
hddtemp, and udisks were no longer working as expected.
These applications incorrectly assume the returned sense data is in
descriptor format, without even looking at the RESPONSE CODE field in the
returned sense data (to see which format the returned sense data is in).
Considering that there will be broken versions of these applications around
roughly forever, we are stuck with being bug compatible with older kernels.
Cc: stable@vger.kernel.org # 4.19+
Reported-by: Stephan Eisvogel <eisvogel@seitics.de>
Reported-by: Christian Heusel <christian@heusel.eu>
Closes: https://lore.kernel.org/linux-ide/0bf3f2f0-0fc6-4ba5-a420-c0874ef82d64@heusel.eu/
Fixes: 28ab9769117c ("ata: libata-scsi: Honor the D_SENSE bit for CK_COND=1 and no error")
Reviewed-by: Hannes Reinecke <hare@suse.de>
Reviewed-by: Martin K. Petersen <martin.petersen@oracle.com>
Link: https://lore.kernel.org/r/20240813131900.1285842-2-cassel@kernel.org
Signed-off-by: Niklas Cassel <cassel@kernel.org>
|
|
Macro `SIMPLE_DEV_PM_OPS()` is deprecated.
This patch replaces `SIMPLE_DEV_PM_OPS()` with
`DEFINE_SIMPLE_DEV_PM_OPS()` currently used.
Expanded results are the same since remaining
member is initialized as zero (NULL):
static SIMPLE_DEV_PM_OPS(rio_pm_ops, rio_suspend, rio_resume);
Expanded to:
static const struct dev_pm_ops __attribute__((__unused__)) rio_pm_ops = {
.suspend = ((1) ? ((rio_suspend)) : ((void *)0)),
.resume = ((1) ? ((rio_resume)) : ((void *)0)),
.freeze = ((1) ? ((rio_suspend)) : ((void *)0)),
.thaw = ((1) ? ((rio_resume)) : ((void *)0)),
.poweroff = ((1) ? ((rio_suspend)) : ((void *)0)),
.restore = ((1) ? ((rio_resume)) : ((void *)0)),
};
static DEFINE_SIMPLE_DEV_PM_OPS(rio_pm_ops, rio_suspend, rio_resume);
Expanded to:
static const struct dev_pm_ops rio_pm_ops = {
.suspend = ((1) ? ((rio_suspend)) : ((void *)0)),
.resume = ((1) ? ((rio_resume)) : ((void *)0)),
.freeze = ((1) ? ((rio_suspend)) : ((void *)0)),
.thaw = ((1) ? ((rio_resume)) : ((void *)0)),
.poweroff = ((1) ? ((rio_suspend)) : ((void *)0)),
.restore = ((1) ? ((rio_resume)) : ((void *)0)),
.runtime_suspend = ((void *)0),
.runtime_resume = ((void *)0),
.runtime_idle = ((void *)0),
};
Signed-off-by: Moon Yeounsu <yyyynoom@gmail.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Commit a0821ca14bb8 ("media: atomisp: Remove test pattern generator (TPG)
support") broke BYT support because it removed a seemingly unused field
from struct sh_css_sp_config and a seemingly unused value from enum
ia_css_input_mode.
But these are part of the ABI between the kernel and firmware on ISP2400
and this part of the TPG support removal changes broke ISP2400 support.
ISP2401 support was not affected because on ISP2401 only a part of
struct sh_css_sp_config is used.
Restore the removed field and enum value to fix this.
Fixes: a0821ca14bb8 ("media: atomisp: Remove test pattern generator (TPG) support")
Cc: stable@vger.kernel.org
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
|
|
Keep the URL in a single line for easier copy-pasting.
Signed-off-by: Enguerrand de Ribaucourt <enguerrand.de-ribaucourt@savoirfairelinux.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Acked-by: Arun Ramadoss <arun.ramadoss@microchip.com>
Link: https://patch.msgid.link/20240812124346.597702-1-enguerrand.de-ribaucourt@savoirfairelinux.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
The value passed as the l3_proto argument of mvneta_txq_desc_csum()
is __be16. And mvneta_txq_desc_csum uses this parameter as a __be16
value. So use __be16 as the type for the parameter, rather than
type with host byte order.
Flagged by Sparse as:
.../mvneta.c:1796:25: warning: restricted __be16 degrades to integer
.../mvneta.c:1979:45: warning: incorrect type in argument 2 (different base types)
.../mvneta.c:1979:45: expected int l3_proto
.../mvneta.c:1979:45: got restricted __be16 [usertype] l3_proto
No functional change intended.
Flagged by Sparse.
Signed-off-by: Simon Horman <horms@kernel.org>
Reviewed-by: Marcin Wojtas <marcin.s.wojtas@gmail.com>
Link: https://patch.msgid.link/20240812-mvneta-be16-v1-1-e1ea12234230@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
`fec_ptp_pps_perout()` reimplements logic already
in `fec_ptp_read()`. Replace with function call.
Signed-off-by: Csókás, Bence <csokas.bence@prolan.hu>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://patch.msgid.link/20240812094713.2883476-2-csokas.bence@prolan.hu
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
This function is used in `fec_ptp_enable_pps()` through
struct cyclecounter read(). Moving the declaration makes
it clearer, what's happening.
Suggested-by: Frank Li <Frank.li@nxp.com>
Link: https://lore.kernel.org/netdev/20240805144754.2384663-1-csokas.bence@prolan.hu/T/#ma6c21ad264016c24612048b1483769eaff8cdf20
Signed-off-by: Csókás, Bence <csokas.bence@prolan.hu>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://patch.msgid.link/20240812094713.2883476-1-csokas.bence@prolan.hu
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
'struct config_item_type' is not modified in this driver.
This structure is only used with config_group_init_type_name() which takes
a const struct config_item_type* as a 3rd argument.
This also makes things consistent with 'netconsole_target_type' witch is
already const.
Constifying this structure moves some data to a read-only section, so
increase overall security, especially when the structure holds some
function pointers.
On a x86_64, with allmodconfig:
Before:
======
text data bss dec hex filename
33007 3952 1312 38271 957f drivers/net/netconsole.o
After:
=====
text data bss dec hex filename
33071 3888 1312 38271 957f drivers/net/netconsole.o
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Reviewed-by: Breno Leitao <leitao@debian.org>
Link: https://patch.msgid.link/9c205b2b4bdb09fc9e9d2cb2f2936ec053da1b1b.1723325900.git.christophe.jaillet@wanadoo.fr
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Introduce adminq commands to configure and retrieve RSS settings from
the device. Implement corresponding ethtool ops for user-level
management.
Signed-off-by: Jeroen de Borst <jeroendb@google.com>
Co-developed-by: Ziwei Xiao <ziweixiao@google.com>
Signed-off-by: Ziwei Xiao <ziweixiao@google.com>
Signed-off-by: Praveen Kaligineedi <pkaligineedi@google.com>
Reviewed-by: Praveen Kaligineedi <pkaligineedi@google.com>
Reviewed-by: Harshitha Ramamurthy <hramamurthy@google.com>
Reviewed-by: Willem de Bruijn <willemb@google.com>
Reviewed-by: Hariprasad Kelam <hkelam@marvell.com>
Link: https://patch.msgid.link/20240812222013.1503584-3-pkaligineedi@google.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Add a device option to inform the driver about the hash key size and
hash table size used by the device. This information will be stored and
made available for RSS ethtool operations.
Signed-off-by: Ziwei Xiao <ziweixiao@google.com>
Signed-off-by: Praveen Kaligineedi <pkaligineedi@google.com>
Reviewed-by: Praveen Kaligineedi <pkaligineedi@google.com>
Reviewed-by: Harshitha Ramamurthy <hramamurthy@google.com>
Reviewed-by: Willem de Bruijn <willemb@google.com>
Link: https://patch.msgid.link/20240812222013.1503584-2-pkaligineedi@google.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Add support for offloading cls U32 filters. Only "skbedit queue_mapping"
and "drop" actions are supported. Also, only "ip" and "802_3" tc
protocols are allowed. The PF must advertise the VIRTCHNL_VF_OFFLOAD_TC_U32
capability flag.
Since the filters will be enabled via the FD stage at the PF, a new type
of FDIR filters is added and the existing list and state machine are used.
The new filters can be used to configure flow directors based on raw
(binary) pattern in the rx packet.
Examples:
0. # tc qdisc add dev enp175s0v0 ingress
1. Redirect UDP from src IP 192.168.2.1 to queue 12:
# tc filter add dev <dev> protocol ip ingress u32 \
match u32 0x45000000 0xff000000 at 0 \
match u32 0x00110000 0x00ff0000 at 8 \
match u32 0xC0A80201 0xffffffff at 12 \
match u32 0x00000000 0x00000000 at 24 \
action skbedit queue_mapping 12 skip_sw
2. Drop all ICMP:
# tc filter add dev <dev> protocol ip ingress u32 \
match u32 0x45000000 0xff000000 at 0 \
match u32 0x00010000 0x00ff0000 at 8 \
match u32 0x00000000 0x00000000 at 24 \
action drop skip_sw
3. Redirect ICMP traffic from MAC 3c:fd:fe:a5:47:e0 to queue 7
(note proto: 802_3):
# tc filter add dev <dev> protocol 802_3 ingress u32 \
match u32 0x00003CFD 0x0000ffff at 4 \
match u32 0xFEA547E0 0xffffffff at 8 \
match u32 0x08004500 0xffffff00 at 12 \
match u32 0x00000001 0x000000ff at 20 \
match u32 0x0000 0x0000 at 40 \
action skbedit queue_mapping 7 skip_sw
Notes on matches:
1 - All intermediate fields that are needed to parse the correct PTYPE
must be provided (in e.g. 3: Ethernet Type 0x0800 in MAC, IP version
and IP length: 0x45 and protocol: 0x01 (ICMP)).
2 - The last match must provide an offset that guarantees all required
headers are accounted for, even if the last header is not matched.
For example, in #2, the last match is 4 bytes at offset 24 starting
from IP header, so the total is 14 (MAC) + 24 + 4 = 42, which is the
sum of MAC+IP+ICMP headers.
Reviewed-by: Sridhar Samudrala <sridhar.samudrala@intel.com>
Reviewed-by: Marcin Szycik <marcin.szycik@linux.intel.com>
Signed-off-by: Ahmed Zaki <ahmed.zaki@intel.com>
Tested-by: Rafal Romanowski <rafal.romanowski@intel.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
|
|
In preparation for a second type of FDIR filters that can be added by
tc-u32, move the add/del of the FDIR logic to be entirely contained in
iavf_fdir.c.
The iavf_find_fdir_fltr_by_loc() is renamed to iavf_find_fdir_fltr()
to be more agnostic to the filter ID parameter (for now @loc, which is
relevant only to current FDIR filters added via ethtool).
The FDIR filter deletion is moved from iavf_del_fdir_ethtool() in
ethtool.c to iavf_fdir_del_fltr(). While at it, fix a minor bug where
the "fltr" is accessed out of the fdir_fltr_lock spinlock protection.
Reviewed-by: Sridhar Samudrala <sridhar.samudrala@intel.com>
Reviewed-by: Marcin Szycik <marcin.szycik@linux.intel.com>
Signed-off-by: Ahmed Zaki <ahmed.zaki@intel.com>
Tested-by: Rafal Romanowski <rafal.romanowski@intel.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
|
|
Enable VFs to create FDIR filters from raw binary patterns.
The corresponding processes for raw flow are added in the
Parse / Create / Destroy stages.
Reviewed-by: Marcin Szycik <marcin.szycik@linux.intel.com>
Signed-off-by: Junfeng Guo <junfeng.guo@intel.com>
Co-developed-by: Ahmed Zaki <ahmed.zaki@intel.com>
Signed-off-by: Ahmed Zaki <ahmed.zaki@intel.com>
Tested-by: Rafal Romanowski <rafal.romanowski@intel.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
|
|
The SWAP Flag in the FDIR Programming Descriptor doesn't work properly,
it is always set and cannot be unset (hardware bug). Thus, add a method
to effectively disable the FDIR SWAP option by setting the FDSWAP instead
of FDINSET registers.
Reviewed-by: Marcin Szycik <marcin.szycik@linux.intel.com>
Signed-off-by: Junfeng Guo <junfeng.guo@intel.com>
Signed-off-by: Ahmed Zaki <ahmed.zaki@intel.com>
Tested-by: Rafal Romanowski <rafal.romanowski@intel.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
|
|
Add API ice_parser_profile_init() to init a parser profile based on
a parser result and a mask buffer. The ice_parser_profile struct is used
by the low level FXP engine to create HW profile/field vectors.
Reviewed-by: Marcin Szycik <marcin.szycik@linux.intel.com>
Signed-off-by: Qi Zhang <qi.z.zhang@intel.com>
Signed-off-by: Junfeng Guo <junfeng.guo@intel.com>
Signed-off-by: Ahmed Zaki <ahmed.zaki@intel.com>
Tested-by: Rafal Romanowski <rafal.romanowski@intel.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
|
|
Add support for the vxlan, geneve, ecpri UDP tunnels through the
following APIs:
- ice_parser_vxlan_tunnel_set()
- ice_parser_geneve_tunnel_set()
- ice_parser_ecpri_tunnel_set()
Reviewed-by: Simon Horman <horms@kernel.org>
Reviewed-by: Marcin Szycik <marcin.szycik@linux.intel.com>
Signed-off-by: Qi Zhang <qi.z.zhang@intel.com>
Signed-off-by: Junfeng Guo <junfeng.guo@intel.com>
Signed-off-by: Ahmed Zaki <ahmed.zaki@intel.com>
Tested-by: Rafal Romanowski <rafal.romanowski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
|
|
Add API ice_parser_dvm_set() to support turning on/off the parser's double
vlan mode.
Reviewed-by: Marcin Szycik <marcin.szycik@linux.intel.com>
Signed-off-by: Qi Zhang <qi.z.zhang@intel.com>
Signed-off-by: Junfeng Guo <junfeng.guo@intel.com>
Co-developed-by: Ahmed Zaki <ahmed.zaki@intel.com>
Signed-off-by: Ahmed Zaki <ahmed.zaki@intel.com>
Tested-by: Rafal Romanowski <rafal.romanowski@intel.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
|
|
Implement the core work of the runtime parser via:
- ice_parser_rt_execute()
- ice_parser_rt_reset()
- ice_parser_rt_pkt_buf_set()
Reviewed-by: Marcin Szycik <marcin.szycik@linux.intel.com>
Signed-off-by: Qi Zhang <qi.z.zhang@intel.com>
Signed-off-by: Junfeng Guo <junfeng.guo@intel.com>
Signed-off-by: Ahmed Zaki <ahmed.zaki@intel.com>
Tested-by: Rafal Romanowski <rafal.romanowski@intel.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
|
|
Add the following internal helper functions:
- ice_bst_tcam_match():
to perform ternary match on boost TCAM.
- ice_pg_cam_match():
to perform parse graph key match in cam table.
- ice_pg_nm_cam_match():
to perform parse graph key no match in cam table.
- ice_ptype_mk_tcam_match():
to perform ptype markers match in tcam table.
- ice_flg_redirect():
to redirect parser flags to packet flags.
- ice_xlt_kb_flag_get():
to aggregate 64 bit packet flag into 16 bit key builder flags.
Reviewed-by: Simon Horman <horms@kernel.org>
Reviewed-by: Aleksandr Loktionov <aleksandr.loktionov@intel.com>
Reviewed-by: Wojciech Drewek <wojciech.drewek@intel.com>
Reviewed-by: Marcin Szycik <marcin.szycik@linux.intel.com>
Signed-off-by: Qi Zhang <qi.z.zhang@intel.com>
Signed-off-by: Junfeng Guo <junfeng.guo@intel.com>
Signed-off-by: Ahmed Zaki <ahmed.zaki@intel.com>
Tested-by: Rafal Romanowski <rafal.romanowski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
|
|
Add debug for all parser sections.
Reviewed-by: Marcin Szycik <marcin.szycik@linux.intel.com>
Signed-off-by: Qi Zhang <qi.z.zhang@intel.com>
Signed-off-by: Junfeng Guo <junfeng.guo@intel.com>
Signed-off-by: Ahmed Zaki <ahmed.zaki@intel.com>
Tested-by: Rafal Romanowski <rafal.romanowski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
|
|
Parse the following DDP sections:
- ICE_SID_RXPARSER_IMEM into an array of struct ice_imem_item
- ICE_SID_RXPARSER_METADATA_INIT into an array of struct ice_metainit_item
- ICE_SID_RXPARSER_CAM or ICE_SID_RXPARSER_PG_SPILL into an array of
struct ice_pg_cam_item
- ICE_SID_RXPARSER_NOMATCH_CAM or ICE_SID_RXPARSER_NOMATCH_SPILL into an
array of struct ice_pg_nm_cam_item
- ICE_SID_RXPARSER_CAM into an array of ice_bst_tcam_item
- ICE_SID_LBL_RXPARSER_TMEM into an array of ice_lbl_item
- ICE_SID_RXPARSER_MARKER_PTYPE into an array of ice_ptype_mk_tcam_item
- ICE_SID_RXPARSER_MARKER_GRP into an array of ice_mk_grp_item
- ICE_SID_RXPARSER_PROTO_GRP into an array of ice_proto_grp_item
- ICE_SID_RXPARSER_FLAG_REDIR into an array of ice_flg_rd_item
- ICE_SID_XLT_KEY_BUILDER_SW, ICE_SID_XLT_KEY_BUILDER_ACL,
ICE_SID_XLT_KEY_BUILDER_FD and ICE_SID_XLT_KEY_BUILDER_RSS into
struct ice_xlt_kb
Reviewed-by: Marcin Szycik <marcin.szycik@linux.intel.com>
Signed-off-by: Qi Zhang <qi.z.zhang@intel.com>
Signed-off-by: Junfeng Guo <junfeng.guo@intel.com>
Co-developed-by: Ahmed Zaki <ahmed.zaki@intel.com>
Signed-off-by: Ahmed Zaki <ahmed.zaki@intel.com>
Tested-by: Rafal Romanowski <rafal.romanowski@intel.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
|
|
Add new parser module which can parse a packet in binary and generate
information like ptype, protocol/offset pairs and flags which can be later
used to feed the FXP profile creation directly.
Add skeleton of the create and destroy APIs:
ice_parser_create()
ice_parser_destroy()
Reviewed-by: Simon Horman <horms@kernel.org>
Reviewed-by: Marcin Szycik <marcin.szycik@linux.intel.com>
Reviewed-by: Wojciech Drewek <wojciech.drewek@intel.com>
Signed-off-by: Qi Zhang <qi.z.zhang@intel.com>
Signed-off-by: Junfeng Guo <junfeng.guo@intel.com>
Co-developed-by: Ahmed Zaki <ahmed.zaki@intel.com>
Signed-off-by: Ahmed Zaki <ahmed.zaki@intel.com>
Tested-by: Rafal Romanowski <rafal.romanowski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
|
|
A recent change to the driver exposed a bug where the MAC RX
filters (unicast MAC, broadcast MAC, and multicast MAC) are
configured and enabled before the RX path is fully initialized.
The result of this bug is that after the PHY is started packets
that match these MAC RX filters start to flow into the RX FIFO.
And then, after rx_init() is completed, these packets will go
into the driver RX ring as well. If enough packets are received
to fill the RX ring (default size is 128 packets) before the call
to request_irq() completes, the driver RX function becomes stuck.
This bug is intermittent but is most likely to be seen where the
oob_net0 interface is connected to a busy network with lots of
broadcast and multicast traffic.
All the MAC RX filters must be disabled until the RX path is ready,
i.e. all initialization is done and all the IRQs are installed.
Fixes: f7442a634ac0 ("mlxbf_gige: call request_irq() after NAPI initialized")
Reviewed-by: Asmaa Mnebhi <asmaa@nvidia.com>
Signed-off-by: David Thompson <davthompson@nvidia.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Link: https://patch.msgid.link/20240809163612.12852-1-davthompson@nvidia.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
doorbell rings
After napi_complete_done() is called when NAPI is polling in the current
process context, another NAPI may be scheduled and start running in
softirq on another CPU and may ring the doorbell before the current CPU
does. When combined with unnecessary rings when there is no need to arm
the CQ, it triggers error paths in the hardware.
This patch fixes this by calling napi_complete_done() after doorbell
rings. It limits the number of unnecessary rings when there is
no need to arm. MANA hardware specifies that there must be one doorbell
ring every 8 CQ wraparounds. This driver guarantees one doorbell ring as
soon as the number of consumed CQEs exceeds 4 CQ wraparounds. In practical
workloads, the 4 CQ wraparounds proves to be big enough that it rarely
exceeds this limit before all the napi weight is consumed.
To implement this, add a per-CQ counter cq->work_done_since_doorbell,
and make sure the CQ is armed as soon as passing 4 wraparounds of the CQ.
Cc: stable@vger.kernel.org
Fixes: e1b5683ff62e ("net: mana: Move NAPI from EQ to CQ")
Reviewed-by: Haiyang Zhang <haiyangz@microsoft.com>
Signed-off-by: Long Li <longli@microsoft.com>
Link: https://patch.msgid.link/1723219138-29887-1-git-send-email-longli@linuxonhyperv.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
Simpler and avoids manual pointer addition.
Signed-off-by: Rosen Penev <rosenp@gmail.com>
Link: https://patch.msgid.link/20240809044957.4534-1-rosenp@gmail.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/ath/ath
ath.git patch for v6.11
We have a single patch for the next 6.11-rc which introduces a
workaround to ath12k which addresses a WCN7850 hardware issue that
prevents proper operation with unaligned transmit buffers.
|
|
The code to lookup the scatter gather table entry assumed that it was
possible to use sg_virt() in order to lookup the DMA address in a mapped
scatter gather table. However, this assumption is incorrect as the DMA
mapping code may merge multiple entries into one. In that case, the DMA
address space may have e.g. two consecutive pages which is correctly
represented by the scatter gather list entry, however the virtual
addresses for these two pages may differ and the relationship cannot be
resolved anymore.
Avoid this problem entirely by working with the offset into the mapped
area instead of using virtual addresses. With that we only use the DMA
length and DMA address from the scatter gather list entries. The
underlying DMA/IOMMU code is therefore free to merge two entries into
one even if the virtual addresses space for the area is not continuous.
Fixes: 90db50755228 ("wifi: iwlwifi: use already mapped data when TXing an AMSDU")
Reported-by: Chris Bainbridge <chris.bainbridge@gmail.com>
Closes: https://lore.kernel.org/r/ZrNRoEbdkxkKFMBi@debian.local
Signed-off-by: Benjamin Berg <benjamin.berg@intel.com>
Tested-by: Chris Bainbridge <chris.bainbridge@gmail.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://patch.msgid.link/20240812110640.460514-1-benjamin@sipsolutions.net
|
|
When disabling wifi mt7921_ipv6_addr_change() is called as a notifier.
At this point mvif->phy is already NULL so we cannot use it here.
Signed-off-by: Bert Karwatzki <spasswolf@web.de>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://patch.msgid.link/20240812104542.80760-1-spasswolf@web.de
|
|
traversal
Current issue:
- The `target_list_lock` spinlock is held while iterating over
target_list() entries.
- Mid-loop, the lock is released to call __netpoll_cleanup(), then
reacquired.
- This practice compromises the protection provided by
`target_list_lock`.
Reason for current design:
1. __netpoll_cleanup() may sleep, incompatible with holding a spinlock.
2. target_list_lock must be a spinlock because write_msg() cannot sleep.
(See commit b5427c27173e ("[NET] netconsole: Support multiple logging
targets"))
Defer the cleanup of the netpoll structure to outside the
target_list_lock() protected area. Create another list
(target_cleanup_list) to hold the entries that need to be cleaned up,
and clean them using a mutex (target_cleanup_list_lock).
Signed-off-by: Breno Leitao <leitao@debian.org>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
The return flow in netconsole's dynamic functions is currently
inconsistent. This patch aims to streamline and standardize the process
by ensuring that the mutex is unlocked before returning the ret value.
Additionally, this update includes a minor functional change where
certain strnlen() operations are performed with the
dynamic_netconsole_mutex locked. This adjustment is not anticipated to
cause any issues, however, it is crucial to document this change for
clarity.
Signed-off-by: Breno Leitao <leitao@debian.org>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
Update variable names from err to ret in cases where the variable may
return non-error values.
This change facilitates a forthcoming patch that relies on ret being
used consistently to handle return values, regardless of whether they
indicate an error or not.
Signed-off-by: Breno Leitao <leitao@debian.org>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
netconsole incorrectly mixes int and ssize_t types by using int for
return variables in functions that should return ssize_t.
This is fixed by updating the return variables to the appropriate
ssize_t type, ensuring consistency across the function definitions.
Signed-off-by: Breno Leitao <leitao@debian.org>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
Add Yanteng Si as MODULE_AUTHOR of Loongson DWMAC PCI driver.
Signed-off-by: Feiyang Chen <chenfeiyang@loongson.cn>
Signed-off-by: Yinggang Gu <guyinggang@loongson.cn>
Acked-by: Huacai Chen <chenhuacai@loongson.cn>
Reviewed-by: Serge Semin <fancer.lancer@gmail.com>
Signed-off-by: Yanteng Si <siyanteng@loongson.cn>
Tested-by: Serge Semin <fancer.lancer@gmail.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
The new generation Loongson LS2K2000 SoC and LS7A2000 chipset are
equipped with the network controllers called Loongson GNET. It's the
single and multi DMA-channels Loongson GMAC but with a PHY attached.
Here is the summary of the DW GMAC features the controller has:
DW GMAC IP-core: v3.73a
Speeds: 10/100/1000Mbps
Duplex: Full (both versions), Half (LS2K2000 GNET only)
DMA-descriptors type: enhanced
L3/L4 filters availability: Y
VLAN hash table filter: Y
PHY-interface: GMII (PHY is integrated into the chips)
Remote Wake-up support: Y
Mac Management Counters (MMC): Y
Number of additional MAC addresses: 5
MAC Hash-based filter: Y
Hash Table Size: 256
AV feature: Y (LS2K2000 GNET only)
DMA channels: 8 (LS2K2000 GNET), 1 (LS7A2000 GNET)
Let's update the Loongson DWMAC driver to supporting the new Loongson
GNET controller. The change is mainly trivial: the driver shall be
bound to the PCIe device with DID 0x7a13, and the device-specific
setup() method shall be called for it. The only peculiarity concerns
the integrated PHY speed change procedure. The PHY has a weird problem
with switching from the low speeds to 1000Mbps mode. The speedup
procedure requires the PHY-link re-negotiation. So the suggested
change provide the device-specific fix_mac_speed() method to overcome
the problem.
Signed-off-by: Feiyang Chen <chenfeiyang@loongson.cn>
Signed-off-by: Yinggang Gu <guyinggang@loongson.cn>
Acked-by: Huacai Chen <chenhuacai@loongson.cn>
Reviewed-by: Serge Semin <fancer.lancer@gmail.com>
Signed-off-by: Yanteng Si <siyanteng@loongson.cn>
Tested-by: Serge Semin <fancer.lancer@gmail.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
The Loongson DWMAC driver currently supports the Loongson GMAC
devices (based on the DW GMAC v3.50a/v3.73a IP-core) installed to the
LS2K1000 SoC and LS7A1000 chipset. But recently a new generation
LS2K2000 SoC was released with the new version of the Loongson GMAC
synthesized in. The new controller is based on the DW GMAC v3.73a
IP-core with the AV-feature enabled, which implies the multi
DMA-channels support. The multi DMA-channels feature has the next
vendor-specific peculiarities:
1. Split up Tx and Rx DMA IRQ status/mask bits:
Name Tx Rx
DMA_INTR_ENA_NIE = 0x00040000 | 0x00020000;
DMA_INTR_ENA_AIE = 0x00010000 | 0x00008000;
DMA_STATUS_NIS = 0x00040000 | 0x00020000;
DMA_STATUS_AIS = 0x00010000 | 0x00008000;
DMA_STATUS_FBI = 0x00002000 | 0x00001000;
2. Custom Synopsys ID hardwired into the GMAC_VERSION.SNPSVER register
field. It's 0x10 while it should have been 0x37 in accordance with
the actual DW GMAC IP-core version.
3. There are eight DMA-channels available meanwhile the Synopsys DW
GMAC IP-core supports up to three DMA-channels.
4. It's possible to have each DMA-channel IRQ independently delivered.
The MSI IRQs must be utilized for that.
Thus in order to have the multi-channels Loongson GMAC controllers
supported let's modify the Loongson DWMAC driver in accordance with
all the peculiarities described above:
1. Create the multi-channels Loongson GMAC-specific
stmmac_dma_ops::dma_interrupt()
stmmac_dma_ops::init_chan()
callbacks due to the non-standard DMA IRQ CSR flags layout.
2. Create the Loongson DWMAC-specific platform setup() method
which gets to initialize the DMA-ops with the dwmac1000_dma_ops
instance and overrides the callbacks described in 1. The method also
overrides the custom Synopsys ID with the real one in order to have
the rest of the HW-specific callbacks correctly detected by the driver
core.
3. Make sure the platform setup() method enables the flow control and
duplex modes supported by the controller.
Signed-off-by: Feiyang Chen <chenfeiyang@loongson.cn>
Signed-off-by: Yinggang Gu <guyinggang@loongson.cn>
Acked-by: Huacai Chen <chenhuacai@loongson.cn>
Signed-off-by: Yanteng Si <siyanteng@loongson.cn>
Reviewed-by: Serge Semin <fancer.lancer@gmail.com>
Tested-by: Serge Semin <fancer.lancer@gmail.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
The Loongson GMAC driver currently supports the network controllers
installed on the LS2K1000 SoC and LS7A1000 chipset, for which the GMAC
devices are required to be defined in the platform device tree source.
But Loongson machines may have UEFI (implies ACPI) or PMON/UBOOT
(implies FDT) as the system bootloaders. In order to have both system
configurations support let's extend the driver functionality with the
case of having the Loongson GMAC probed on the PCI bus with no device
tree node defined for it. That requires to make the device DT-node
optional, to rely on the IRQ line detected by the PCI core and to
have the MDIO bus ID calculated using the PCIe Domain+BDF numbers.
In order to have the device probe() and remove() methods less
complicated let's move the DT- and ACPI-specific code to the
respective sub-functions.
Signed-off-by: Feiyang Chen <chenfeiyang@loongson.cn>
Signed-off-by: Yinggang Gu <guyinggang@loongson.cn>
Acked-by: Huacai Chen <chenhuacai@loongson.cn>
Signed-off-by: Yanteng Si <siyanteng@loongson.cn>
Reviewed-by: Serge Semin <fancer.lancer@gmail.com>
Tested-by: Serge Semin <fancer.lancer@gmail.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
The Loongson GNET device support is about to be added in one of the
next commits. As another preparation for that introduce the PCI device
info data with a setup() callback performing the device-specific
platform data initializations. Currently it is utilized for the
already supported Loongson GMAC device only.
Signed-off-by: Feiyang Chen <chenfeiyang@loongson.cn>
Signed-off-by: Yinggang Gu <guyinggang@loongson.cn>
Reviewed-by: Serge Semin <fancer.lancer@gmail.com>
Acked-by: Huacai Chen <chenhuacai@loongson.cn>
Signed-off-by: Yanteng Si <siyanteng@loongson.cn>
Tested-by: Serge Semin <fancer.lancer@gmail.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
PHY-interface of the Loongson GMAC device is RGMII with no internal
delays added to the data lines signal. So to comply with that let's
pre-initialize the platform-data field with the respective enum
constant.
Signed-off-by: Feiyang Chen <chenfeiyang@loongson.cn>
Signed-off-by: Yinggang Gu <guyinggang@loongson.cn>
Reviewed-by: Serge Semin <fancer.lancer@gmail.com>
Acked-by: Huacai Chen <chenhuacai@loongson.cn>
Signed-off-by: Yanteng Si <siyanteng@loongson.cn>
Tested-by: Serge Semin <fancer.lancer@gmail.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
Reference and PTP clocks rate of the Loongson GMAC devices is 125MHz.
(So is in the GNET devices which support is about to be added.) Set
the respective plat_stmmacenet_data field up in accordance with that
so to have the coalesce command and timestamping work correctly.
Fixes: 30bba69d7db4 ("stmmac: pci: Add dwmac support for Loongson")
Signed-off-by: Feiyang Chen <chenfeiyang@loongson.cn>
Signed-off-by: Yinggang Gu <guyinggang@loongson.cn>
Reviewed-by: Serge Semin <fancer.lancer@gmail.com>
Acked-by: Huacai Chen <chenhuacai@loongson.cn>
Signed-off-by: Yanteng Si <siyanteng@loongson.cn>
Tested-by: Serge Semin <fancer.lancer@gmail.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
Loongson delivers two types of the network devices: Loongson GMAC and
Loongson GNET in the framework of four SOC/Chipsets revisions:
Chip Network PCI Dev ID Synopys Version DMA-channel
LS2K1000 SOC GMAC 0x7a03 v3.50a/v3.73a 1
LS7A1000 Chipset GMAC 0x7a03 v3.50a/v3.73a 1
LS2K2000 SOC GMAC 0x7a03 v3.73a 8
LS2K2000 SOC GNET 0x7a13 v3.73a 8
LS7A2000 Chipset GNET 0x7a13 v3.73a 1
The driver currently supports the chips with the Loongson GMAC network
device synthesized with a single DMA-channel available. As a
preparation before adding the Loongson GNET support detach the
Loongson GMAC-specific platform data initializations to the
loongson_gmac_data() method and preserve the common settings in the
loongson_default_data().
While at it drop the return value statement from the
loongson_default_data() method as redundant.
Note there is no intermediate vendor-specific PCS in between the MAC
and PHY on Loongson GMAC and GNET. So the plat->mac_interface field
can be freely initialized with the PHY_INTERFACE_MODE_NA value.
Signed-off-by: Feiyang Chen <chenfeiyang@loongson.cn>
Signed-off-by: Yinggang Gu <guyinggang@loongson.cn>
Reviewed-by: Serge Semin <fancer.lancer@gmail.com>
Acked-by: Huacai Chen <chenhuacai@loongson.cn>
Signed-off-by: Yanteng Si <siyanteng@loongson.cn>
Tested-by: Serge Semin <fancer.lancer@gmail.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
identification
For the readability sake convert the hard-coded Loongson GMAC PCI ID to
the respective macro and use the PCI_DEVICE_DATA() macro-function to
create the pci_device_id array entry. The later change will be
specifically useful in order to assign the device-specific data for the
currently supported device and for about to be added Loongson GNET
controller.
Signed-off-by: Feiyang Chen <chenfeiyang@loongson.cn>
Signed-off-by: Yinggang Gu <guyinggang@loongson.cn>
Reviewed-by: Serge Semin <fancer.lancer@gmail.com>
Acked-by: Huacai Chen <chenhuacai@loongson.cn>
Signed-off-by: Yanteng Si <siyanteng@loongson.cn>
Tested-by: Serge Semin <fancer.lancer@gmail.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
The Loongson GMAC driver currently doesn't utilize the MSI IRQs, but
retrieves the IRQs specified in the device DT-node. Let's drop the
direct pci_enable_msi()/pci_disable_msi() calls then as redundant
Signed-off-by: Feiyang Chen <chenfeiyang@loongson.cn>
Signed-off-by: Yinggang Gu <guyinggang@loongson.cn>
Reviewed-by: Serge Semin <fancer.lancer@gmail.com>
Acked-by: Huacai Chen <chenhuacai@loongson.cn>
Signed-off-by: Yanteng Si <siyanteng@loongson.cn>
Tested-by: Serge Semin <fancer.lancer@gmail.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
The plat_stmmacenet_data::multicast_filter_bins field is twice
initialized in the loongson_default_data() method. Drop the redundant
initialization, but for the readability sake keep the filters init
statements defined in the same place of the method.
Signed-off-by: Feiyang Chen <chenfeiyang@loongson.cn>
Signed-off-by: Yinggang Gu <guyinggang@loongson.cn>
Reviewed-by: Serge Semin <fancer.lancer@gmail.com>
Acked-by: Huacai Chen <chenhuacai@loongson.cn>
Signed-off-by: Yanteng Si <siyanteng@loongson.cn>
Tested-by: Serge Semin <fancer.lancer@gmail.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
Export the DW GMAC DMA-ops descriptor so one could be available in
the low-level platform drivers. It will be utilized to override some
callbacks in order to handle the LS2K2000 GNET device specifics. The
GNET controller support is being added in one of the following up
commits.
Signed-off-by: Feiyang Chen <chenfeiyang@loongson.cn>
Signed-off-by: Yinggang Gu <guyinggang@loongson.cn>
Reviewed-by: Serge Semin <fancer.lancer@gmail.com>
Acked-by: Huacai Chen <chenhuacai@loongson.cn>
Signed-off-by: Yanteng Si <siyanteng@loongson.cn>
Tested-by: Serge Semin <fancer.lancer@gmail.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
DW GMAC v3.73 can be equipped with the Audio Video (AV) feature which
enables transmission of time-sensitive traffic over bridged local area
networks (DWC Ethernet QoS Product). In that case there can be up to two
additional DMA-channels available with no Tx COE support (unless there is
vendor-specific IP-core alterations). Each channel is implemented as a
separate Control and Status register (CSR) for managing the transmit and
receive functions, descriptor handling, and interrupt handling.
Add the multi-channels DW GMAC controllers support just by making sure the
already implemented DMA-configs are performed on the per-channel basis.
Note the only currently known instance of the multi-channel DW GMAC
IP-core is the LS2K2000 GNET controller, which has been released with the
vendor-specific feature extension of having eight DMA-channels. The device
support will be added in one of the following up commits.
Signed-off-by: Feiyang Chen <chenfeiyang@loongson.cn>
Signed-off-by: Yinggang Gu <guyinggang@loongson.cn>
Reviewed-by: Serge Semin <fancer.lancer@gmail.com>
Acked-by: Huacai Chen <chenhuacai@loongson.cn>
Signed-off-by: Yanteng Si <siyanteng@loongson.cn>
Tested-by: Serge Semin <fancer.lancer@gmail.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
ATDS (Alternate Descriptor Size) is a part of the DMA Bus Mode configs
(together with PBL, ALL, EME, etc) of the DW GMAC controllers. Seeing
it's not changed at runtime but is activated as long as the IP-core
has it supported (at least due to the Type 2 Full Checksum Offload
Engine feature), move the respective parameter from the
stmmac_dma_ops::init() callback argument to the stmmac_dma_cfg
structure, which already have the rest of the DMA-related configs
defined.
Besides the being added in the next commit DW GMAC multi-channels
support will require to add the stmmac_dma_ops::init_chan() callback
and have the ATDS flag set/cleared for each channel in there. Having
the atds-flag in the stmmac_dma_cfg structure will make the parameter
accessible from stmmac_dma_ops::init_chan() callback too.
Signed-off-by: Feiyang Chen <chenfeiyang@loongson.cn>
Signed-off-by: Yinggang Gu <guyinggang@loongson.cn>
Reviewed-by: Serge Semin <fancer.lancer@gmail.com>
Acked-by: Huacai Chen <chenhuacai@loongson.cn>
Signed-off-by: Yanteng Si <siyanteng@loongson.cn>
Tested-by: Serge Semin <fancer.lancer@gmail.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
Commit d88cabfd9abc ("nfp: Avoid -Wflex-array-member-not-at-end
warnings") introduced tagged `struct nfp_dump_tl_hdr`. We want
to ensure that when new members need to be added to the flexible
structure, they are always included within this tagged struct.
So, we use `static_assert()` to ensure that the memory layout for
both the flexible structure and the tagged struct is the same after
any changes.
Signed-off-by: Gustavo A. R. Silva <gustavoars@kernel.org>
Reviewed-by: Simon Horman <horms@kernel.org>
Link: https://patch.msgid.link/ZrVB43Hen0H5WQFP@cute
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
In macb_suspend(), idev->ifa_list is fetched with rcu_access_pointer()
and later the pointer is dereferenced as ifa->ifa_local.
So, idev->ifa_list must be fetched with rcu_dereference().
Fixes: 0cb8de39a776 ("net: macb: Add ARP support to WOL")
Signed-off-by: Kuniyuki Iwashima <kuniyu@amazon.com>
Link: https://patch.msgid.link/20240808040021.6971-1-kuniyu@amazon.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
