| Age | Commit message (Collapse) | Author |
|---|
|
Use the %u format for unsigned int parameters handling with sscanf() and
sysfs_emit() to avoid compilation warnings. In
fsl_sata_rx_watermark_store(), the call to sscanf() to parse a single
argument is replaced with a call to kstrtouint().
While at it, also replace the printk(KERN_ERR) calls with dev_err()
calls and fix blank lines in fsl_sata_rx_watermark_store().
Reported-by: kernel test robot <lkp@intel.com>
Signed-off-by: Damien Le Moal <damien.lemoal@opensource.wdc.com>
|
|
Messages around firmware download were incorrectly tagged as being related
to discovery trace events. Thus, firmware download status ended up dumping
the trace log as well as the firmware update message. As there were a
couple of log messages in this state, the trace log was dumped multiple
times.
Resolve this by converting from trace events to SLI events.
Link: https://lore.kernel.org/r/20220207180442.72836-1-jsmart2021@gmail.com
Reviewed-by: Ewan D. Milne <emilne@redhat.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
The driver is initiating NVMe PRLIs to determine device NVMe support. This
should not be occurring if CONFIG_NVME_FC support is disabled.
Correct this by changing the default value for FC4 support. Currently it
defaults to FCP and NVMe. With change, when NVME_FC support is not enabled
in the kernel, the default value is just FCP.
Link: https://lore.kernel.org/r/20220207180516.73052-1-jsmart2021@gmail.com
Reviewed-by: Ewan D. Milne <emilne@redhat.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
It is mandatory for a software to issue a reset upon modifying RGMII
Receive Timing Control and RGMII Transmit Timing Control bit fields of MAC
Specific Control register 2 (page 2, register 21) otherwise the changes
won't be perceived by the PHY (the same is applicable for a lot of other
registers). Not setting the RGMII delays on the platforms that imply it'
being done on the PHY side will consequently cause the traffic loss. We
discovered that the denoted soft-reset is missing in the
m88e1121_config_aneg() method for the case if the RGMII delays are
modified but the MDIx polarity isn't changed or the auto-negotiation is
left enabled, thus causing the traffic loss on our platform with Marvell
Alaska 88E1510 installed. Let's fix that by issuing the soft-reset if the
delays have been actually set in the m88e1121_config_aneg_rgmii_delays()
method.
Cc: stable@vger.kernel.org
Fixes: d6ab93364734 ("net: phy: marvell: Avoid unnecessary soft reset")
Signed-off-by: Pavel Parkhomenko <Pavel.Parkhomenko@baikalelectronics.ru>
Reviewed-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Reviewed-by: Serge Semin <fancer.lancer@gmail.com>
Link: https://lore.kernel.org/r/20220205203932.26899-1-Pavel.Parkhomenko@baikalelectronics.ru
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
We need to wait for sensor settling time (~ 3/ODR) before reading data
in st_lsm6dsx_read_oneshot routine in order to avoid corrupted samples.
Fixes: 290a6ce11d93 ("iio: imu: add support to lsm6dsx driver")
Reported-by: Mario Tesi <mario.tesi@st.com>
Tested-by: Mario Tesi <mario.tesi@st.com>
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Link: https://lore.kernel.org/r/b41ebda5535895298716c76d939f9f165fcd2d13.1644098120.git.lorenzo@kernel.org
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/dlemoal/libata
Pull ata fix from Damien Le Moal:
"A single patch from me, to fix a bug that is causing boot issues in
the field (reports of problems with Fedora 35).
The bug affects mostly old-ish drives that have issues with read log
page command handling"
* tag 'ata-5.17-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/dlemoal/libata:
ata: libata-core: Fix ata_dev_config_cpr()
|
|
After commit e3728b50cd9b ("ACPI: PM: s2idle: Avoid possible race
related to the EC GPE") wakeup interrupts occurring immediately after
the one discarded by acpi_s2idle_wake() may be missed. Moreover, if
the SCI triggers again immediately after the rearming in
acpi_s2idle_wake(), that wakeup may be missed too.
The problem is that pm_system_irq_wakeup() only calls pm_system_wakeup()
when pm_wakeup_irq is 0, but that's not the case any more after the
interrupt causing acpi_s2idle_wake() to run until pm_wakeup_irq is
cleared by the pm_wakeup_clear() call in s2idle_loop(). However,
there may be wakeup interrupts occurring in that time frame and if
that happens, they will be missed.
To address that issue first move the clearing of pm_wakeup_irq to
the point at which it is known that the interrupt causing
acpi_s2idle_wake() to tun will be discarded, before rearming the SCI
for wakeup. Moreover, because that only reduces the size of the
time window in which the issue may manifest itself, allow
pm_system_irq_wakeup() to register two second wakeup interrupts in
a row and, when discarding the first one, replace it with the second
one. [Of course, this assumes that only one wakeup interrupt can be
discarded in one go, but currently that is the case and I am not
aware of any plans to change that.]
Fixes: e3728b50cd9b ("ACPI: PM: s2idle: Avoid possible race related to the EC GPE")
Cc: 5.4+ <stable@vger.kernel.org> # 5.4+
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
Commit 4a9af6cac050 ("ACPI: EC: Rework flushing of EC work while
suspended to idle") made acpi_ec_dispatch_gpe() check
pm_wakeup_pending(), but that is before canceling the SCI wakeup,
so pm_wakeup_pending() is always true. This causes the loop in
acpi_ec_dispatch_gpe() to always terminate after one iteration which
may not be correct.
Address this issue by canceling the SCI wakeup earlier, from
acpi_ec_dispatch_gpe() itself.
Fixes: 4a9af6cac050 ("ACPI: EC: Rework flushing of EC work while suspended to idle")
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
Testing on various upcoming OEM systems shows commit 7b167c4cb48e ("ACPI:
PM: Only mark EC GPE for wakeup on Intel systems") was short
sighted and the symptoms were indicative of other problems. Some OEMs
do have the dedicated GPIOs for the power button but also rely upon
an interrupt to the EC SCI to let the lid work.
The original commit showed spurious activity on Lenovo systems:
* On both Lenovo T14 and P14s the keyboard wakeup doesn't work, and
sometimes the power button event doesn't work.
This was confirmed on my end at that time.
However further development in the kernel showed that the issue was
actually the IRQ for the GPIO controller was also shared with the EC SCI.
This was actually fixed by commit 2d54067fcd23 ("pinctrl: amd: Fix
wakeups when IRQ is shared with SCI").
The original commit also showed problems with AC adapter:
* On HP 635 G7 detaching or attaching AC during suspend will cause
the system not to wakeup
* On Asus vivobook to prevent detaching AC causing resume problems
* On Lenovo 14ARE05 to prevent detaching AC causing resume problems
* On HP ENVY x360 to prevent detaching AC causing resume problems
Detaching AC adapter causing problems appears to have been a problem
because the EC SCI went off to notify the OS of the power adapter change
but the SCI was ignored and there was no other way to wake up this system
since GPIO controller wasn't properly enabled. The wakeups were fixed by
enabling the GPIO controller in commit acd47b9f28e5 ("pinctrl: amd: Handle
wake-up interrupt").
I've confirmed on a variety of OEM notebooks with the following test
1) echo 1 | sudo tee /sys/power/pm_debug_messages
2) sudo systemctl suspend
3) unplug AC adapter, make sure system is still asleep
4) wake system from lid (which is provided by ACPI SCI on some of them)
5) dmesg
a) see the EC GPE dispatched, timekeeping for X seconds (matching ~time
until AC adapter plug out)
b) see timekeeping for Y seconds until woke (matching ~time from AC
adapter until lid event)
6) Look at /sys/kernel/debug/amd_pmc/s0ix_stats
"Time (in us) in S0i3" = X + Y - firmware processing time
Signed-off-by: Mario Limonciello <mario.limonciello@amd.com>
Tested-by: Kai-Heng Feng <kai.heng.feng@canonical.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/ulfh/mmc
Pull MMC fixes from Ulf Hansson:
"MMC core:
- Fix support for SD Power off notification
MMC host:
- moxart: Fix potential use-after-free on remove path
- sdhci-of-esdhc: Fix error path when setting dma mask
- sh_mmcif: Fix potential NULL pointer dereference"
* tag 'mmc-v5.17-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/ulfh/mmc:
moxart: fix potential use-after-free on remove path
mmc: core: Wait for command setting 'Power Off Notification' bit to complete
mmc: sh_mmcif: Check for null res pointer
mmc: sdhci-of-esdhc: Check for error num after setting mask
|
|
Using DMA_BIT_MASK(64) as an initializer for a global variable
causes problems with Clang 12.0.1. The compiler doesn't understand
that value 64 is excluded from the shift at compile time, resulting
in a build error.
While this is a compiler problem, avoid the issue by setting up
the dma_mask memory as part of struct hv_device, and initialize
it using dma_set_mask().
Reported-by: Nathan Chancellor <nathan@kernel.org>
Reported-by: Vitaly Chikunov <vt@altlinux.org>
Reported-by: Jakub Kicinski <kuba@kernel.org>
Fixes: 743b237c3a7b ("scsi: storvsc: Add Isolation VM support for storvsc driver")
Signed-off-by: Michael Kelley <mikelley@microsoft.com>
Reviewed-by: Nathan Chancellor <nathan@kernel.org>
Tested-by: Nathan Chancellor <nathan@kernel.org>
Link: https://lore.kernel.org/r/1644176216-12531-1-git-send-email-mikelley@microsoft.com
Signed-off-by: Wei Liu <wei.liu@kernel.org>
|
|
kobject_init_and_add() takes reference even when it fails.
According to the doc of kobject_init_and_add()：
If this function returns an error, kobject_put() must be called to
properly clean up the memory associated with the object.
Fix memory leak by calling kobject_put().
Fixes: c2e5df616e1a ("vmbus: add per-channel sysfs info")
Signed-off-by: Miaoqian Lin <linmq006@gmail.com>
Reviewed-by: Juan Vazquez <juvazq@linux.microsoft.com>
Link: https://lore.kernel.org/r/20220203173008.43480-1-linmq006@gmail.com
Signed-off-by: Wei Liu <wei.liu@kernel.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap into arm/fixes
Fixes for omaps
A series of fixes for omap variants for minor issues, and a fix for a timer
regression for some omap3 beagleboard versions.
The timer fix needs to patch both the dts and the timer code because
otherwise the timer quirk handling for old dtbs will prevent the dts fix
from working.
The other changes are for issues found by automated analysis, a macasp
typo fix, and two cosmetic fixes for clocks.
* tag 'omap-for-v5.17/fixes-for-merge-window-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
ARM: dts: Don't use legacy clock defines for dra7 clkctrl
clk: ti: Move dra7 clock devices out of the legacy section
ARM: dts: Fix timer regression for beagleboard revision c
ARM: dts: am335x-wega: Fix typo in mcasp property rx-num-evt
ARM: OMAP2+: adjust the location of put_device() call in omapdss_init_of
ARM: OMAP2+: hwmod: Add of_node_put() before break
Link: https://lore.kernel.org/r/pull-1641801310-149268@atomide.com
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
git://git.linaro.org/people/jens.wiklander/linux-tee into arm/fixes
OP-TEE fix shutdown problems
* tag 'optee-fix-for-v5.17' of git://git.linaro.org/people/jens.wiklander/linux-tee:
optee: use driver internal tee_context for some rpc
Link: https://lore.kernel.org/r/20220203132323.GA4132001@jade
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
The CLKT register contains at poweron 0x40, which at our typical 100kHz
bus rate means .64ms. But there is no specified limit to how long devices
should be able to stretch the clocks, so just disable the timeout. We
still have a timeout wrapping the entire transfer.
Signed-off-by: Eric Anholt <eric@anholt.net>
Signed-off-by: Stefan Wahren <stefan.wahren@i2se.com>
BugLink: https://github.com/raspberrypi/linux/issues/3064
Signed-off-by: Wolfram Sang <wsa@kernel.org>
|
|
The concurrent positioning ranges log page 47h is a general purpose log
page and not a subpage of the indentify device log. Using
ata_identify_page_supported() to test for concurrent positioning ranges
support is thus wrong. ata_log_supported() must be used.
Furthermore, unlike other advanced ATA features (e.g. NCQ priority),
accesses to the concurrent positioning ranges log page are not gated by
a feature bit from the device IDENTIFY data. Since many older drives
react badly to the READ LOG EXT and/or READ LOG DMA EXT commands isued
to read device log pages, avoid problems with older drives by limiting
the concurrent positioning ranges support detection to drives
implementing at least the ACS-4 ATA standard (major version 11). This
additional condition effectively turns ata_dev_config_cpr() into a nop
for older drives, avoiding problems in the field.
Fixes: fe22e1c2f705 ("libata: support concurrent positioning ranges log")
BugLink: https://bugzilla.kernel.org/show_bug.cgi?id=215519
Cc: stable@vger.kernel.org
Reviewed-by: Hannes Reinecke <hare@suse.de>
Tested-by: Abderraouf Adjal <adjal.arf@gmail.com>
Signed-off-by: Damien Le Moal <damien.lemoal@opensource.wdc.com>
|
|
Fix the following warning from "make htmldocs":
drivers/gpu/drm/drm_privacy_screen.c:270:
WARNING: Inline emphasis start-string without end-string.
Fixes: 8a12b170558a ("drm/privacy-screen: Add notifier support (v2)")
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Reviewed-by: Simon Ser <contact@emersion.fr>
Link: https://lore.kernel.org/r/20220207130407.389585-1-hdegoede@redhat.com
Link: https://patchwork.freedesktop.org/patch/msgid/20220207130407.389585-1-hdegoede@redhat.com
|
|
On TGL/RKL the BIOS likes to use some kind of bogus DBUF layout
that doesn't match what the spec recommends. With a single active
pipe that is not going to be a problem, but with multiple pipes
active skl_commit_modeset_enables() goes into an infinite loop
since it can't figure out any order in which it can commit the
pipes without causing DBUF overlaps between the planes.
We'd need some kind of extra DBUF defrag stage in between to
make the transition possible. But that is clearly way too complex
a solution, so in the name of simplicity let's just sanitize the
DBUF state by simply turning off all planes when we detect a
pipe encroaching on its neighbours' DBUF slices. We only have
to disable the primary planes as all other planes should have
already been disabled (if they somehow were enabled) by
earlier sanitization steps.
And for good measure let's also sanitize in case the DBUF
allocations of the pipes already seem to overlap each other.
Cc: <stable@vger.kernel.org> # v5.14+
Closes: https://gitlab.freedesktop.org/drm/intel/-/issues/4762
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20220204141818.1900-3-ville.syrjala@linux.intel.com
Reviewed-by: Stanislav Lisovskiy <stanislav.lisovskiy@intel.com>
(cherry picked from commit 15512021eb3975a8c2366e3883337e252bb0eee5)
Signed-off-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
|
|
During readout we cannot assume the planes are actually using the
slices they are supposed to use. The BIOS may have misprogrammed
things and put the planes onto the wrong dbuf slices. So let's
do the readout more carefully to make sure we really know which
dbuf slices are actually in use by the pipe at the time.
Cc: <stable@vger.kernel.org> # v5.14+
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20220204141818.1900-2-ville.syrjala@linux.intel.com
Reviewed-by: Stanislav Lisovskiy <stanislav.lisovskiy@intel.com>
(cherry picked from commit b3dcc6dc0f32612d04839c2fb32e94d0ebf92c98)
Signed-off-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
|
|
Reintroduce the !join_mbus single pipe cases for adlp+.
Due to the mbus relative dbuf offsets in PLANE_BUF_CFG we
need to know the actual slices used by the pipe when doing
readout, even when mbus joining isn't enabled. Accurate
readout will be needed to properly sanitize invalid BIOS
dbuf configurations.
This will also make it much easier to play around with the
!join_mbus configs for testin/workaround purposes.
Cc: <stable@vger.kernel.org> # v5.14+
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20220204141818.1900-1-ville.syrjala@linux.intel.com
Reviewed-by: Stanislav Lisovskiy <stanislav.lisovskiy@intel.com>
(cherry picked from commit eef173954432fe0612acb63421a95deb41155cdc)
Signed-off-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
|
|
Architectures others than x86 have a stub implementation calling
WARN_ON_ONCE(). The appropriate headers need to be included, otherwise
the header-test target will fail with:
HDRTEST drivers/gpu/drm/i915/i915_mm.h
In file included from <command-line>:
./drivers/gpu/drm/i915/i915_mm.h: In function ‘remap_io_mapping’:
./drivers/gpu/drm/i915/i915_mm.h:26:2: error: implicit declaration of function ‘WARN_ON_ONCE’ [-Werror=implicit-function-declaration]
26 | WARN_ON_ONCE(1);
| ^~~~~~~~~~~~
v2: Do not include <linux/printk.h> since call to pr_err() has been
removed
Fixes: 67c430bbaae1 ("drm/i915: Skip remap_io_mapping() for non-x86 platforms")
Cc: Siva Mullati <siva.mullati@intel.com>
Signed-off-by: Lucas De Marchi <lucas.demarchi@intel.com>
Reviewed-by: Siva Mullati <siva.mullati@intel.com>
Reviewed-by: José Roberto de Souza <jose.souza@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20220131165926.3230642-3-lucas.demarchi@intel.com
(cherry picked from commit 377c675f3c17ffaefd023ee283bb366bbd6bbcea)
Signed-off-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
|
|
The i915_ttm_accel_move() function may return error codes that should
be propagated further up the stack rather than consumed assuming that
the accel move failed and could be replaced with a memcpy move.
For -EINTR, -ERESTARTSYS and -EAGAIN, just propagate those codes, rather
than retrying with a memcpy move.
Fixes: 2b0a750caf33 ("drm/i915/ttm: Failsafe migration blits")
Cc: Matthew Auld <matthew.auld@intel.com>
Signed-off-by: Thomas Hellström <thomas.hellstrom@linux.intel.com>
Reviewed-by: Matthew Auld <matthew.auld@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20220201070340.16457-1-thomas.hellstrom@linux.intel.com
(cherry picked from commit 29b9702ffe70d83b9970abbccaeb287dfda4409f)
Signed-off-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
|
|
Currently we allow DRRS on IVB PCH ports, but we're missing a
few programming steps meaning it is guaranteed to not work.
And on HSW DRRS is not supported on anything but port A ever
as only transcoder EDP has the M2/N2 registers (though I'm
not sure if HSW ever has eDP on any other port).
Starting from BDW all transcoders have the dynamically
reprogrammable M/N registers so DRRS could work on any
port.
Stop initializing DRRS on ports where it cannot possibly work.
Cc: stable@vger.kernel.org
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20220128103757.22461-11-ville.syrjala@linux.intel.com
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
(cherry picked from commit f0d4ce59f4d48622044933054a0e0cefa91ba15e)
Signed-off-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
|
|
We call __save_depot_stack() unconditionally so the stack depot
must always be initialized or else we'll oops on platforms without
runtime pm support.
Presumably we've not seen this in CI due to stack_depot_init()
already getting called via drm_mm_init()+CONFIG_DRM_DEBUG_MM.
Cc: Vlastimil Babka <vbabka@suse.cz>
Cc: Dmitry Vyukov <dvyukov@google.com>
Cc: Marco Elver <elver@google.com> # stackdepot
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Imre Deak <imre.deak@intel.com>
Fixes: 2dba5eb1c73b ("lib/stackdepot: allow optional init and stack_table allocation by kvmalloc()")
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20220126081539.23227-1-ville.syrjala@linux.intel.com
Acked-by: Vlastimil Babka <vbabka@suse.cz>
Reviewed-by: Imre Deak <imre.deak@intel.com>
(cherry picked from commit 751a9d69b19702af35b0fedfb8ff362027c1cf0c)
Signed-off-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
|
|
The variable is assigned twice to the same value. Let's drop one.
Reported-by: kernel test robot <yujie.liu@intel.com>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Reviewed-by: Sam Ravnborg <sam@ravnborg.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20220203151151.1270461-1-maxime@cerno.tech
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull irq fix from Borislav Petkov:
"Remove a bogus warning introduced by the recent PCI MSI irq affinity
overhaul"
* tag 'irq_urgent_for_v5.17_rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
PCI/MSI: Remove bogus warning in pci_irq_get_affinity()
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/ras/ras
Pull EDAC fixes from Borislav Petkov:
"Fix altera and xgene EDAC drivers to propagate the correct error code
from platform_get_irq() so that deferred probing still works"
* tag 'edac_urgent_for_v5.17_rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/ras/ras:
EDAC/xgene: Fix deferred probing
EDAC/altera: Fix deferred probing
|
|
For default mechanism, product would use default MRU 3500 if
they didn't define it. But for Cinterion MV31-W, there is a known
issue which MRU 3500 would lead to data connection lost.
So we align it with Qualcomm default MRU settings.
Link: https://lore.kernel.org/r/20220119102519.5342-1-slark_xiao@163.com
[mani: Modified the commit message to reflect Cinterion MV31-W and CCed stable]
Fixes: 87693e092bd0 ("bus: mhi: pci_generic: Add Cinterion MV31-W PCIe to MHI")
Cc: stable@vger.kernel.org # v5.14 +
Reviewed-by: Manivannan Sadhasivam <mani@kernel.org>
Signed-off-by: Slark Xiao <slark_xiao@163.com>
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Link: https://lore.kernel.org/r/20220205135731.157871-3-manivannan.sadhasivam@linaro.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
For default mechanism, product would use default MRU 3500 if
they didn't define it. But for Foxconn SDX55, there is a known
issue which MRU 3500 would lead to data connection lost.
So we align it with Qualcomm default MRU settings.
Link: https://lore.kernel.org/r/20220119101213.5008-1-slark_xiao@163.com
[mani: Added pci_generic prefix to subject and CCed stable]
Fixes: aac426562f56 ("bus: mhi: pci_generic: Introduce Foxconn T99W175 support")
Cc: stable@vger.kernel.org # v5.12+
Reviewed-by: Manivannan Sadhasivam <mani@kernel.org>
Signed-off-by: Slark Xiao <slark_xiao@163.com>
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Link: https://lore.kernel.org/r/20220205135731.157871-2-manivannan.sadhasivam@linaro.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
When setting up autonegotiation for 88E1118R and compatible PHYs,
a software reset of PHY is issued before setting up polarity.
This is incorrect as changes of MDI Crossover Mode bits are
disruptive to the normal operation and must be followed by a
software reset to take effect. Let's patch m88e1118_config_aneg()
to fix the issue mentioned before by invoking software reset
of the PHY just after setting up MDI-x polarity.
Fixes: 605f196efbf8 ("phy: Add support for Marvell 88E1118 PHY")
Signed-off-by: Pavel Parkhomenko <Pavel.Parkhomenko@baikalelectronics.ru>
Reviewed-by: Serge Semin <fancer.lancer@gmail.com>
Suggested-by: Andrew Lunn <andrew@lunn.ch>
Cc: stable@vger.kernel.org
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
In the function panel_simple_probe() the pointer panel->desc is
assigned to the passed pointer desc. If function panel_dpi_probe()
is called panel->desc will be updated, but further on only desc
will be evaluated. So update the desc pointer to be able to use
the data from the function panel_dpi_probe().
Fixes: 4a1d0dbc8332 ("drm/panel: simple: add panel-dpi support")
Signed-off-by: Christoph Niedermaier <cniedermaier@dh-electronics.com>
Cc: Marek Vasut <marex@denx.de>
Cc: Thierry Reding <thierry.reding@gmail.com>
Cc: Sam Ravnborg <sam@ravnborg.org>
Cc: David Airlie <airlied@linux.ie>
Cc: Daniel Vetter <daniel@ffwll.ch>
To: dri-devel@lists.freedesktop.org
Reviewed-by: Sam Ravnborg <sam@ravnborg.org>
Signed-off-by: Marek Vasut <marex@denx.de>
Link: https://patchwork.freedesktop.org/patch/msgid/20220201110153.3479-1-cniedermaier@dh-electronics.com
|
|
The filters for the PTP trap keys are incorrectly configured, in the
sense that is2_entry_set() only looks at trap->key.ipv4.dport or
trap->key.ipv6.dport if trap->key.ipv4.proto or trap->key.ipv6.proto is
set to IPPROTO_TCP or IPPROTO_UDP.
But we don't do that, so is2_entry_set() goes through the "else" branch
of the IP protocol check, and ends up installing a rule for "Any IP
protocol match" (because msk is also 0). The UDP port is ignored.
This means that when we run "ptp4l -i swp0 -4", all IP traffic is
trapped to the CPU, which hinders bridging.
Fix this by specifying the IP protocol in the VCAP IS2 filters for PTP
over UDP.
Fixes: 96ca08c05838 ("net: mscc: ocelot: set up traps for PTP packets")
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The fan curve control patches introduced a regression for at least the
TUF FX506 and possibly other TUF series laptops that do not have support
for fan curve control.
As part of the probing process, asus_wmi_evaluate_method_buf is called
to get the factory default fan curve . The WMI management function
returns 0 on certain laptops to indicate lack of fan curve control
instead of ASUS_WMI_UNSUPPORTED_METHOD. This 0 is transformed to
-ENODATA which results in failure when probing.
Fixes: 0f0ac158d28f ("platform/x86: asus-wmi: Add support for custom fan curves")
Reported-and-tested-by: Abhijeet V <abhijeetviswa@gmail.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Link: https://lore.kernel.org/r/20220205112840.33095-1-hdegoede@redhat.com
|
|
This patch adds support for the UGTABLET WP5540 digitizer tablet
devices. Without it, the pen moves the cursor, but neither the
buttons nor the tap sensor in the tip do work.
Signed-off-by: Sergio Costas <rastersoft@gmail.com>
Link: https://lore.kernel.org/r/63dece1d-91ca-1b1b-d90d-335be66896be@gmail.com
Cc: stable@vger.kernel.org
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/phy/linux-phy into char-misc-next
Vinod writes:
phy: fixes for 5.17
Fixes for bunch of drivers:
- clk params for dphy
- arg fix for mtk-tphy
- refcount leak fix for stm32
- bus width fix for zynqmp
- sentinel fix ti
- PHY_BRCM_USB Kconfig fix
- clk fix for usb phy
* tag 'phy-fixes-5.17' of git://git.kernel.org/pub/scm/linux/kernel/git/phy/linux-phy:
phy: dphy: Correct clk_pre parameter
phy: phy-mtk-tphy: Fix duplicated argument in phy-mtk-tphy
phy: stm32: fix a refcount leak in stm32_usbphyc_pll_enable()
phy: xilinx: zynqmp: Fix bus width setting for SGMII
phy: cadence: Sierra: fix error handling bugs in probe()
phy: ti: Fix missing sentinel for clk_div_table
phy: broadcom: Kconfig: Fix PHY_BRCM_USB config option
phy: usb: Leave some clocks running during suspend
|
|
Pull rdma fixes from Jason Gunthorpe:
"Some medium sized bugs in the various drivers. A couple are more
recent regressions:
- Fix two panics in hfi1 and two allocation problems
- Send the IGMP to the correct address in cma
- Squash a syzkaller bug related to races reading the multicast list
- Memory leak in siw and cm
- Fix a corner case spec compliance for HFI/QIB
- Correct the implementation of fences in siw
- Error unwind bug in mlx4"
* tag 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/rdma/rdma:
RDMA/mlx4: Don't continue event handler after memory allocation failure
RDMA/siw: Fix broken RDMA Read Fence/Resume logic.
IB/rdmavt: Validate remote_addr during loopback atomic tests
IB/cm: Release previously acquired reference counter in the cm_id_priv
RDMA/siw: Fix refcounting leak in siw_create_qp()
RDMA/ucma: Protect mc during concurrent multicast leaves
RDMA/cma: Use correct address when leaving multicast group
IB/hfi1: Fix tstats alloc and dealloc
IB/hfi1: Fix AIP early init panic
IB/hfi1: Fix alloc failure with larger txqueuelen
IB/hfi1: Fix panic with larger ipoib send_queue_size
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi
Pull SCSI fixes from James Bottomley:
"Seven fixes, six of which are fairly obvious driver fixes.
The one core change to the device budget depth is to try to ensure
that if the default depth is large (which can produce quite a sizeable
bitmap allocation per device), we give back the memory we don't need
if there's a queue size reduction in slave_configure (which happens to
a lot of devices)"
* tag 'scsi-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi:
scsi: hisi_sas: Fix setting of hisi_sas_slot.is_internal
scsi: pm8001: Fix use-after-free for aborted SSP/STP sas_task
scsi: pm8001: Fix use-after-free for aborted TMF sas_task
scsi: pm8001: Fix warning for undescribed param in process_one_iomb()
scsi: core: Reallocate device's budget map on queue depth change
scsi: bnx2fc: Make bnx2fc_recv_frame() mp safe
scsi: pm80xx: Fix double completion for SATA devices
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci
Pull pci fixes from Bjorn Helgaas:
- Restructure j721e_pcie_probe() so we don't dereference a NULL pointer
(Bjorn Helgaas)
- Add a kirin_pcie_data struct to identify different Kirin variants to
fix probe failure for controllers with an internal PHY (Bjorn
Helgaas)
* tag 'pci-v5.17-fixes-3' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci:
PCI: kirin: Add dev struct for of_device_get_match_data()
PCI: j721e: Initialize pcie->cdns_pcie before using it
|
|
Bean reported that a622435fbe1a ("PCI: kirin: Prefer
of_device_get_match_data()") broke kirin_pcie_probe() because it assumed
match data of 0 was a failure when in fact, it meant the match data was
"(void *)PCIE_KIRIN_INTERNAL_PHY".
Therefore, probing of "hisilicon,kirin960-pcie" devices failed with -EINVAL
and an "OF data missing" message.
Add a struct kirin_pcie_data to encode the PHY type. Then the result of
of_device_get_match_data() should always be a non-NULL pointer to a struct
kirin_pcie_data that contains the PHY type.
Fixes: a622435fbe1a ("PCI: kirin: Prefer of_device_get_match_data()")
Link: https://lore.kernel.org/r/20220202162659.GA12603@bhelgaas
Link: https://lore.kernel.org/r/20220201215941.1203155-1-huobean@gmail.com
Reported-by: Bean Huo <beanhuo@micron.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
|
|
Pull block fixes from Jens Axboe:
- NVMe pull request
- fix use-after-free in rdma and tcp controller reset (Sagi Grimberg)
- fix the state check in nvmf_ctlr_matches_baseopts (Uday Shankar)
- MD nowait null pointer fix (Song)
- blk-integrity seed advance fix (Martin)
- Fix a dio regression in this merge window (Ilya)
* tag 'block-5.17-2022-02-04' of git://git.kernel.dk/linux-block:
block: bio-integrity: Advance seed correctly for larger interval sizes
nvme-fabrics: fix state check in nvmf_ctlr_matches_baseopts()
md: fix NULL pointer deref with nowait but no mddev->queue
block: fix DIO handling regressions in blkdev_read_iter()
nvme-rdma: fix possible use-after-free in transport error_recovery work
nvme-tcp: fix possible use-after-free in transport error_recovery work
nvme: fix a possible use-after-free in controller reset during load
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/dlemoal/libata
Pull ATA fixes from Damien Le Moal:
- Sergey volunteered to be a reviewer for the Renesas R-Car SATA driver
and PATA drivers. Update the MAINTAINERS file accordingly.
- Regression fix: add a horkage flag to prevent accessing the log
directory log page with SATADOM-ML 3ME SATA devices as they react
badly to reading that log page (from Anton).
* tag 'ata-5.17-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/dlemoal/libata:
ata: libata-core: Introduce ATA_HORKAGE_NO_LOG_DIR horkage
MAINTAINERS: add myself as Renesas R-Car SATA driver reviewer
MAINTAINERS: add myself as PATA drivers reviewer
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/joro/iommu
Pull iommu fixes from Joerg Roedel:
- Warning fixes and a fix for a potential use-after-free in IOMMU core
code
- Another potential memory leak fix for the Intel VT-d driver
- Fix for an IO polling loop timeout issue in the AMD IOMMU driver
* tag 'iommu-fixes-v5.17-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/joro/iommu:
iommu/amd: Fix loop timeout issue in iommu_ga_log_enable()
iommu/vt-d: Fix potential memory leak in intel_setup_irq_remapping()
iommu: Fix some W=1 warnings
iommu: Fix potential use-after-free during probe
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/crng/random
Pull random number generator fixes from Jason Donenfeld:
"For this week, we have:
- A fix to make more frequent use of hwgenerator randomness, from
Dominik.
- More cleanups to the boot initialization sequence, from Dominik.
- A fix for an old shortcoming with the ZAP ioctl, from me.
- A workaround for a still unfixed Clang CFI/FullLTO compiler bug,
from me. On one hand, it's a bummer to commit workarounds for
experimental compiler features that have bugs. But on the other, I
think this actually improves the code somewhat, independent of the
bug. So a win-win"
* tag 'random-5.17-rc3-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/crng/random:
random: only call crng_finalize_init() for primary_crng
random: access primary_pool directly rather than through pointer
random: wake up /dev/random writers after zap
random: continually use hwgenerator randomness
lib/crypto: blake2s: avoid indirect calls to compression function for Clang CFI
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull ACPI fix from Rafael Wysocki:
"Fix compilation in the case when ACPI is selected and CRC32, depended
on by ACPI after recent changes, is not (Randy Dunlap)"
* tag 'acpi-5.17-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
ACPI: require CRC32 to build
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound
Pull sound fixes from Takashi Iwai:
"A collection of small fixes.
The major changes are ASoC core fixes, addressing the DPCM locking
issue after the recent code changes and the potentially invalid
register accesses via control API. Also, HD-audio got a core fix for
Oops at dynamic unbinding.
The rest are device-specific small fixes, including the usual stuff
like HD-audio and USB-audio quirks"
* tag 'sound-5.17-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound: (31 commits)
ALSA: hda: Skip codec shutdown in case the codec is not registered
ALSA: usb-audio: Correct quirk for VF0770
ALSA: Replace acpi_bus_get_device()
Input: wm97xx: Simplify resource management
ALSA: hda/realtek: Add quirk for ASUS GU603
ALSA: hda/realtek: Fix silent output on Gigabyte X570 Aorus Xtreme after reboot from Windows
ALSA: hda/realtek: Fix silent output on Gigabyte X570S Aorus Master (newer chipset)
ALSA: hda/realtek: Add missing fixup-model entry for Gigabyte X570 ALC1220 quirks
ALSA: hda: realtek: Fix race at concurrent COEF updates
ASoC: ops: Check for negative values before reading them
ASoC: rt5682: Fix deadlock on resume
ASoC: hdmi-codec: Fix OOB memory accesses
ASoC: soc-pcm: Move debugfs removal out of spinlock
ASoC: soc-pcm: Fix DPCM lockdep warning due to nested stream locks
ASoC: fsl: Add missing error handling in pcm030_fabric_probe
ALSA: hda: Fix signedness of sscanf() arguments
ALSA: usb-audio: initialize variables that could ignore errors
ALSA: hda: Fix UAF of leds class devs at unbinding
ASoC: qdsp6: q6apm-dai: only stop graphs that are started
ASoC: codecs: wcd938x: fix return value of mixer put function
...
|
|
Pull drm fixes from Dave Airlie:
"Regular fixes for the week. Daniel has agreed to bring back the fbcon
hw acceleration under a CONFIG option for the non-drm fbdev users, we
don't advise turning this on unless you are in the niche that is old
fbdev drivers, Since it's essentially a revert and shouldn't be high
impact seemed like a good time to do it now.
Otherwise, i915 and amdgpu fixes are most of it, along with some minor
fixes elsewhere.
fbdev:
- readd fbcon acceleration
i915:
- fix DP monitor via type-c dock
- fix for engine busyness and read timeout with GuC
- use ALLOW_FAIL for error capture buffer allocs
- don't use interruptible lock on error paths
- smatch fix to reject zero sized overlays.
amdgpu:
- mGPU fan boost fix for beige goby
- S0ix fixes
- Cyan skillfish hang fix
- DCN fixes for DCN 3.1
- DCN fixes for DCN 3.01
- Apple retina panel fix
- ttm logic inversion fix
dma-buf:
- heaps: fix potential spectre v1 gadget
kmb:
- fix potential oob access
mxsfb:
- fix NULL ptr deref
nouveau:
- fix potential oob access during BIOS decode"
* tag 'drm-fixes-2022-02-04' of git://anongit.freedesktop.org/drm/drm: (24 commits)
drm: mxsfb: Fix NULL pointer dereference
drm/amdgpu: fix logic inversion in check
drm/amd: avoid suspend on dGPUs w/ s2idle support when runtime PM enabled
drm/amd/display: Force link_rate as LINK_RATE_RBR2 for 2018 15" Apple Retina panels
drm/amd/display: revert "Reset fifo after enable otg"
drm/amd/display: watermark latencies is not enough on DCN31
drm/amd/display: Update watermark values for DCN301
drm/amdgpu: fix a potential GPU hang on cyan skillfish
drm/amd: Only run s3 or s0ix if system is configured properly
drm/amd: add support to check whether the system is set to s3
fbcon: Add option to enable legacy hardware acceleration
Revert "fbcon: Disable accelerated scrolling"
Revert "fbdev: Garbage collect fbdev scrolling acceleration, part 1 (from TODO list)"
drm/i915/pmu: Fix KMD and GuC race on accessing busyness
dma-buf: heaps: Fix potential spectre v1 gadget
drm/amd: Warn users about potential s0ix problems
drm/amd/pm: correct the MGpuFanBoost support for Beige Goby
drm/nouveau: fix off by one in BIOS boundary checking
drm/i915/adlp: Fix TypeC PHY-ready status readout
drm/i915/pmu: Use PM timestamp instead of RING TIMESTAMP for reference
...
|
|
crng_finalize_init() returns instantly if it is called for another pool
than primary_crng. The test whether crng_finalize_init() is still required
can be moved to the relevant caller in crng_reseed(), and
crng_need_final_init can be reset to false if crng_finalize_init() is
called with workqueues ready. Then, no previous callsite will call
crng_finalize_init() unless it is needed, and we can get rid of the
superfluous function parameter.
Signed-off-by: Dominik Brodowski <linux@dominikbrodowski.net>
Signed-off-by: Jason A. Donenfeld <Jason@zx2c4.com>
|
|
Both crng_initialize_primary() and crng_init_try_arch_early() are
only called for the primary_pool. Accessing it directly instead of
through a function parameter simplifies the code.
Signed-off-by: Dominik Brodowski <linux@dominikbrodowski.net>
Signed-off-by: Jason A. Donenfeld <Jason@zx2c4.com>
|
|
When account() is called, and the amount of entropy dips below
random_write_wakeup_bits, we wake up the random writers, so that they
can write some more in. However, the RNDZAPENTCNT/RNDCLEARPOOL ioctl
sets the entropy count to zero -- a potential reduction just like
account() -- but does not unblock writers. This commit adds the missing
logic to that ioctl to unblock waiting writers.
Reviewed-by: Dominik Brodowski <linux@dominikbrodowski.net>
Signed-off-by: Jason A. Donenfeld <Jason@zx2c4.com>
|
|
The rngd kernel thread may sleep indefinitely if the entropy count is
kept above random_write_wakeup_bits by other entropy sources. To make
best use of multiple sources of randomness, mix entropy from hardware
RNGs into the pool at least once within CRNG_RESEED_INTERVAL.
Cc: Herbert Xu <herbert@gondor.apana.org.au>
Cc: Jason A. Donenfeld <Jason@zx2c4.com>
Signed-off-by: Dominik Brodowski <linux@dominikbrodowski.net>
Signed-off-by: Jason A. Donenfeld <Jason@zx2c4.com>
|
