| Age | Commit message (Collapse) | Author |
|---|
|
A malicious device can leak heap data to user space
providing bogus frame lengths. Introduce a sanity check.
Signed-off-by: Oliver Neukum <oneukum@suse.com>
Reviewed-by: Grant Grundler <grundler@chromium.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When a 6pack device is detaching, the sixpack_close() will act to cleanup
necessary resources. Although del_timer_sync() in sixpack_close()
won't return if there is an active timer, one could use mod_timer() in
sp_xmit_on_air() to wake up timer again by calling userspace syscall such
as ax25_sendmsg(), ax25_connect() and ax25_ioctl().
This unexpected waked handler, sp_xmit_on_air(), realizes nothing about
the undergoing cleanup and may still call pty_write() to use driver layer
resources that have already been released.
One of the possible race conditions is shown below:
(USE) | (FREE)
ax25_sendmsg() |
ax25_queue_xmit() |
... |
sp_xmit() |
sp_encaps() | sixpack_close()
sp_xmit_on_air() | del_timer_sync(&sp->tx_t)
mod_timer(&sp->tx_t,...) | ...
| unregister_netdev()
| ...
(wait a while) | tty_release()
| tty_release_struct()
| release_tty()
sp_xmit_on_air() | tty_kref_put(tty_struct) //FREE
pty_write(tty_struct) //USE | ...
The corresponding fail log is shown below:
===============================================================
BUG: KASAN: use-after-free in __run_timers.part.0+0x170/0x470
Write of size 8 at addr ffff88800a652ab8 by task swapper/2/0
...
Call Trace:
...
queue_work_on+0x3f/0x50
pty_write+0xcd/0xe0pty_write+0xcd/0xe0
sp_xmit_on_air+0xb2/0x1f0
call_timer_fn+0x28/0x150
__run_timers.part.0+0x3c2/0x470
run_timer_softirq+0x3b/0x80
__do_softirq+0xf1/0x380
...
This patch reorders the del_timer_sync() after the unregister_netdev()
to avoid UAF bugs. Because the unregister_netdev() is well synchronized,
it flushs out any pending queues, waits the refcount of net_device
decreases to zero and removes net_device from kernel. There is not any
running routines after executing unregister_netdev(). Therefore, we could
not arouse timer from userspace again.
Signed-off-by: Duoming Zhou <duoming@zju.edu.cn>
Reviewed-by: Lin Ma <linma@zju.edu.cn>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
DSL and CM (Cable Modem) support 8 B max transfer size and have a custom
DT binding for that reason. This driver was checking for a wrong
"compatible" however which resulted in an incorrect setup.
Fixes: e2e5a2c61837 ("i2c: brcmstb: Adding support for CM and DSL SoCs")
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
|
|
Without DRM_GEM_CMA_HELPER i.MX8MQ DCSS won't build. This needs to be
there.
Signed-off-by: Rudi Heitbaum <rudi@heitbaum.com>
Reviewed-by: Laurentiu Palcu <laurentiu.palcu@oss.nxp.com>
Signed-off-by: Laurentiu Palcu <laurentiu.palcu@oss.nxp.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20220216212228.1217831-1-rudi@heitbaum.com
|
|
Devkit8000 board seems to always used 32k_counter as clocksource.
Restore this behavior.
If clocksource is back to 32k_counter, timer12 is now the clockevent
source (as before) and timer2 is not longer needed here.
This commit fixes the same issue observed with commit 23885389dbbb
("ARM: dts: Fix timer regression for beagleboard revision c") when sleep
is blocked until hitting keys over serial console.
Fixes: aba1ad05da08 ("clocksource/drivers/timer-ti-dm: Add clockevent and clocksource support")
Fixes: e428e250fde6 ("ARM: dts: Configure system timers for omap3")
Signed-off-by: Anthoine Bourgeois <anthoine.bourgeois@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
The mmc0 clock gate bit was mistakenly assigned to "i2s" clock.
You can find that the same bit is assigned to "mmc0" too.
It leads to mmc0 hang for a long time after any sound activity
also it prevented PM_SLEEP to work properly.
I guess it was introduced by copy-paste from jz4740 driver
where it is really controls I2S clock gate.
Fixes: 226dfa4726eb ("clk: Add Ingenic jz4725b CGU driver")
Signed-off-by: Siarhei Volkau <lis8215@gmail.com>
Tested-by: Siarhei Volkau <lis8215@gmail.com>
Reviewed-by: Paul Cercueil <paul@crapouillou.net>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/20220205171849.687805-2-lis8215@gmail.com
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
|
|
Just like in commit 05cf3ec00d46 ("clk: qcom: gcc-msm8996: Drop (again)
gcc_aggre1_pnoc_ahb_clk") adding NoC clocks turned out to be a huge
mistake, as they cause a lot of issues at little benefit (basically
letting Linux know about their children's frequencies), especially when
mishandled or misconfigured.
Adding these ones broke SDCC approx 99 out of 100 times, but that somehow
went unnoticed. To prevent further issues like this one, remove them.
This commit is effectively a revert of 74a33fac3aab ("clk: qcom:
gcc-msm8994: Add missing NoC clocks") with ABI preservation.
Fixes: 74a33fac3aab ("clk: qcom: gcc-msm8994: Add missing NoC clocks")
Signed-off-by: Konrad Dybcio <konrad.dybcio@somainline.org>
Link: https://lore.kernel.org/r/20220217232408.78932-1-konrad.dybcio@somainline.org
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
|
|
elfcorehdr_addr is fixed address passed to Second kernel which may be conflicted
with potential reserved memory in Second kernel,so fdt_reserve_elfcorehdr() ahead
of fdt_init_reserved_mem() can relieve this situation.
Signed-off-by: Nikhil Gupta <nikhil.gupta@nxp.com>
Signed-off-by: Rob Herring <robh@kernel.org>
Link: https://lore.kernel.org/r/20220128042321.15228-1-nikhil.gupta@nxp.com
|
|
Pull drm fixes from Dave Airlie:
"Regular fixes for rc5, nothing really stands out, mostly some amdgpu
and i915 fixes with mediatek, radeon and some misc fixes.
cma-helper:
- set VM_DONTEXPAND
atomic:
- error handling fix
mediatek:
- fix probe defer loop with external bridge
amdgpu:
- Stable pstate clock fixes for Dimgrey Cavefish and Beige Goby
- S0ix SDMA fix
- Yellow Carp GPU reset fix
radeon:
- Backlight fix for iMac 12,1
i915:
- GVT kerneldoc cleanup.
- GVT Kconfig should depend on X86
- Prevent out of range access in SWSCI display code
- Fix mbus join and dbuf slice config lookup
- Fix inverted priority selection in the TTM backend
- Fix FBC plane end Y offset check"
* tag 'drm-fixes-2022-02-18' of git://anongit.freedesktop.org/drm/drm:
drm/atomic: Don't pollute crtc_state->mode_blob with error pointers
drm/radeon: Fix backlight control on iMac 12,1
drm/amd/pm: correct the sequence of sending gpu reset msg
drm/amdgpu: skipping SDMA hw_init and hw_fini for S0ix.
drm/amd/pm: correct UMD pstate clocks for Dimgrey Cavefish and Beige Goby
drm/i915/fbc: Fix the plane end Y offset check
drm/i915/opregion: check port number bounds for SWSCI display power state
drm/i915/ttm: tweak priority hint selection
drm/i915: Fix mbus join config lookup
drm/i915: Fix dbuf slice config lookup
drm/cma-helper: Set VM_DONTEXPAND for mmap
drm/mediatek: mtk_dsi: Avoid EPROBE_DEFER loop with external bridge
drm/i915/gvt: Make DRM_I915_GVT depend on X86
drm/i915/gvt: clean up kernel-doc in gtt.c
|
|
git://anongit.freedesktop.org/drm/drm-intel into drm-fixes
- GVT kerneldoc cleanup. (Randy Dunlap)
- GVT Kconfig should depend on X86. (Siva Mullati)
- Prevent out of range access in SWSCI display code. (Jani Nikula)
- Fix mbus join and dbuf slice config lookup. (Ville Syrjälä)
- Fix inverted priority selection in the TTM backend. (Matthew Auld)
- Fix FBC plane end Y offset check. (Ville Syrjälä)
Signed-off-by: Dave Airlie <airlied@redhat.com>
From: Tvrtko Ursulin <tvrtko.ursulin@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/Yg4lA6k8+xp8u3aB@tursulin-mobl2
|
|
git://anongit.freedesktop.org/drm/drm-misc into drm-fixes
* drm/cma-helper: Set VM_DONTEXPAND
* drm/atomic: Fix error handling in drm_atomic_set_mode_for_crtc()
Signed-off-by: Dave Airlie <airlied@redhat.com>
From: Thomas Zimmermann <tzimmermann@suse.de>
Link: https://patchwork.freedesktop.org/patch/msgid/Yg4mzQALMX69UmA3@linux-uq9g
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net
Pull networking fixes from Jakub Kicinski:
"Including fixes from wireless and netfilter.
Current release - regressions:
- dsa: lantiq_gswip: fix use after free in gswip_remove()
- smc: avoid overwriting the copies of clcsock callback functions
Current release - new code bugs:
- iwlwifi:
- fix use-after-free when no FW is present
- mei: fix the pskb_may_pull check in ipv4
- mei: retry mapping the shared area
- mvm: don't feed the hardware RFKILL into iwlmei
Previous releases - regressions:
- ipv6: mcast: use rcu-safe version of ipv6_get_lladdr()
- tipc: fix wrong publisher node address in link publications
- iwlwifi: mvm: don't send SAR GEO command for 3160 devices, avoid FW
assertion
- bgmac: make idm and nicpm resource optional again
- atl1c: fix tx timeout after link flap
Previous releases - always broken:
- vsock: remove vsock from connected table when connect is
interrupted by a signal
- ping: change destination interface checks to match raw sockets
- crypto: af_alg - get rid of alg_memory_allocated to avoid confusing
semantics (and null-deref) after SO_RESERVE_MEM was added
- ipv6: make exclusive flowlabel checks per-netns
- bonding: force carrier update when releasing slave
- sched: limit TC_ACT_REPEAT loops
- bridge: multicast: notify switchdev driver whenever MC processing
gets disabled because of max entries reached
- wifi: brcmfmac: fix crash in brcm_alt_fw_path when WLAN not found
- iwlwifi: fix locking when "HW not ready"
- phy: mediatek: remove PHY mode check on MT7531
- dsa: mv88e6xxx: flush switchdev FDB workqueue before removing VLAN
- dsa: lan9303:
- fix polarity of reset during probe
- fix accelerated VLAN handling"
* tag 'net-5.17-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net: (65 commits)
bonding: force carrier update when releasing slave
nfp: flower: netdev offload check for ip6gretap
ipv6: fix data-race in fib6_info_hw_flags_set / fib6_purge_rt
ipv4: fix data races in fib_alias_hw_flags_set
net: dsa: lan9303: add VLAN IDs to master device
net: dsa: lan9303: handle hwaccel VLAN tags
vsock: remove vsock from connected table when connect is interrupted by a signal
Revert "net: ethernet: bgmac: Use devm_platform_ioremap_resource_byname"
ping: fix the dif and sdif check in ping_lookup
net: usb: cdc_mbim: avoid altsetting toggling for Telit FN990
net: sched: limit TC_ACT_REPEAT loops
tipc: fix wrong notification node addresses
net: dsa: lantiq_gswip: fix use after free in gswip_remove()
ipv6: per-netns exclusive flowlabel checks
net: bridge: multicast: notify switchdev driver whenever MC processing gets disabled
CDC-NCM: avoid overflow in sanity checking
mctp: fix use after free
net: mscc: ocelot: fix use-after-free in ocelot_vlan_del()
bonding: fix data-races around agg_select_timer
dpaa2-eth: Initialize mutex used in one step timestamping path
...
|
|
In __bond_release_one(), bond_set_carrier() is only called when bond
device has no slave. Therefore, if we remove the up slave from a master
with two slaves and keep the down slave, the master will remain up.
Fix this by moving bond_set_carrier() out of if (!bond_has_slaves(bond))
statement.
Reproducer:
$ insmod bonding.ko mode=0 miimon=100 max_bonds=2
$ ifconfig bond0 up
$ ifenslave bond0 eth0 eth1
$ ifconfig eth0 down
$ ifenslave -d bond0 eth1
$ cat /proc/net/bonding/bond0
Fixes: ff59c4563a8d ("[PATCH] bonding: support carrier state for master")
Signed-off-by: Zhang Changzhong <zhangchangzhong@huawei.com>
Acked-by: Jay Vosburgh <jay.vosburgh@canonical.com>
Link: https://lore.kernel.org/r/1645021088-38370-1-git-send-email-zhangchangzhong@huawei.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
IPv6 GRE tunnels are not being offloaded, this is caused by a missing
netdev offload check. The functionality of IPv6 GRE tunnel offloading
was previously added but this check was not included. Adding the
ip6gretap check allows IPv6 GRE tunnels to be offloaded correctly.
Fixes: f7536ffb0986 ("nfp: flower: Allow ipv6gretap interface for offloading")
Signed-off-by: Danie du Toit <danie.dutoit@corigine.com>
Signed-off-by: Louis Peens <louis.peens@corigine.com>
Signed-off-by: Simon Horman <simon.horman@corigine.com>
Link: https://lore.kernel.org/r/20220217124820.40436-1-louis.peens@corigine.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Because fib6_info_hw_flags_set() is called without any synchronization,
all accesses to gi6->offload, fi->trap and fi->offload_failed
need some basic protection like READ_ONCE()/WRITE_ONCE().
BUG: KCSAN: data-race in fib6_info_hw_flags_set / fib6_purge_rt
read to 0xffff8881087d5886 of 1 bytes by task 13953 on cpu 0:
fib6_drop_pcpu_from net/ipv6/ip6_fib.c:1007 [inline]
fib6_purge_rt+0x4f/0x580 net/ipv6/ip6_fib.c:1033
fib6_del_route net/ipv6/ip6_fib.c:1983 [inline]
fib6_del+0x696/0x890 net/ipv6/ip6_fib.c:2028
__ip6_del_rt net/ipv6/route.c:3876 [inline]
ip6_del_rt+0x83/0x140 net/ipv6/route.c:3891
__ipv6_dev_ac_dec+0x2b5/0x370 net/ipv6/anycast.c:374
ipv6_dev_ac_dec net/ipv6/anycast.c:387 [inline]
__ipv6_sock_ac_close+0x141/0x200 net/ipv6/anycast.c:207
ipv6_sock_ac_close+0x79/0x90 net/ipv6/anycast.c:220
inet6_release+0x32/0x50 net/ipv6/af_inet6.c:476
__sock_release net/socket.c:650 [inline]
sock_close+0x6c/0x150 net/socket.c:1318
__fput+0x295/0x520 fs/file_table.c:280
____fput+0x11/0x20 fs/file_table.c:313
task_work_run+0x8e/0x110 kernel/task_work.c:164
tracehook_notify_resume include/linux/tracehook.h:189 [inline]
exit_to_user_mode_loop kernel/entry/common.c:175 [inline]
exit_to_user_mode_prepare+0x160/0x190 kernel/entry/common.c:207
__syscall_exit_to_user_mode_work kernel/entry/common.c:289 [inline]
syscall_exit_to_user_mode+0x20/0x40 kernel/entry/common.c:300
do_syscall_64+0x50/0xd0 arch/x86/entry/common.c:86
entry_SYSCALL_64_after_hwframe+0x44/0xae
write to 0xffff8881087d5886 of 1 bytes by task 1912 on cpu 1:
fib6_info_hw_flags_set+0x155/0x3b0 net/ipv6/route.c:6230
nsim_fib6_rt_hw_flags_set drivers/net/netdevsim/fib.c:668 [inline]
nsim_fib6_rt_add drivers/net/netdevsim/fib.c:691 [inline]
nsim_fib6_rt_insert drivers/net/netdevsim/fib.c:756 [inline]
nsim_fib6_event drivers/net/netdevsim/fib.c:853 [inline]
nsim_fib_event drivers/net/netdevsim/fib.c:886 [inline]
nsim_fib_event_work+0x284f/0x2cf0 drivers/net/netdevsim/fib.c:1477
process_one_work+0x3f6/0x960 kernel/workqueue.c:2307
worker_thread+0x616/0xa70 kernel/workqueue.c:2454
kthread+0x2c7/0x2e0 kernel/kthread.c:327
ret_from_fork+0x1f/0x30
value changed: 0x22 -> 0x2a
Reported by Kernel Concurrency Sanitizer on:
CPU: 1 PID: 1912 Comm: kworker/1:3 Not tainted 5.16.0-syzkaller #0
Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS Google 01/01/2011
Workqueue: events nsim_fib_event_work
Fixes: 0c5fcf9e249e ("IPv6: Add "offload failed" indication to routes")
Fixes: bb3c4ab93e44 ("ipv6: Add "offload" and "trap" indications to routes")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Amit Cohen <amcohen@nvidia.com>
Cc: Ido Schimmel <idosch@nvidia.com>
Reported-by: syzbot <syzkaller@googlegroups.com>
Link: https://lore.kernel.org/r/20220216173217.3792411-2-eric.dumazet@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
If the master device does VLAN filtering, the IDs used by the switch
must be added for any frames to be received. Do this in the
port_enable() function, and remove them in port_disable().
Fixes: a1292595e006 ("net: dsa: add new DSA switch driver for the SMSC-LAN9303")
Signed-off-by: Mans Rullgard <mans@mansr.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Link: https://lore.kernel.org/r/20220216204818.28746-1-mans@mansr.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
This reverts commit 3710e80952cf2dc48257ac9f145b117b5f74e0a5.
Since idm_base and nicpm_base are still optional resources not present
on all platforms, this breaks the driver for everything except Northstar
2 (which has both).
The same change was already reverted once with 755f5738ff98 ("net:
broadcom: fix a mistake about ioremap resource").
So let's do it again.
Fixes: 3710e80952cf ("net: ethernet: bgmac: Use devm_platform_ioremap_resource_byname")
Signed-off-by: Jonas Gorski <jonas.gorski@gmail.com>
[florian: Added comments to explain the resources are optional]
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://lore.kernel.org/r/20220216184634.2032460-1-f.fainelli@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
At boot on the BCM2711, if the HDMI controllers are running, the CRTC
driver will disable itself and its associated HDMI controller to work
around a hardware bug that would leave some pixels stuck in a FIFO.
In order to avoid that issue, we need to run some operations in lockstep
between the CRTC and HDMI controller, and we need to make sure the HDMI
controller will be powered properly.
However, since we haven't enabled it through KMS, the runtime_pm state
is off at this point so we need to make sure the device is powered
through pm_runtime_resume_and_get, and once the operations are complete,
we call pm_runtime_put.
However, the HDMI controller will do that itself in its
post_crtc_powerdown, which means we'll end up calling pm_runtime_put for
a single pm_runtime_get, throwing the reference counting off. Let's
remove the pm_runtime_put call in the CRTC code in order to have the
proper counting.
Fixes: bca10db67bda ("drm/vc4: crtc: Make sure the HDMI controller is powered when disabling")
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Reviewed-by: Javier Martinez Canillas <javierm@redhat.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20220203102003.1114673-1-maxime@cerno.tech
|
|
On bind we will register the HDMI codec device but we don't unregister
it on unbind, leading to a device leakage. Unregister our device at
unbind.
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Reviewed-by: Javier Martinez Canillas <javierm@redhat.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20220127111452.222002-1-maxime@cerno.tech
|
|
The qib driver load has been failing with the following message:
sysfs: cannot create duplicate filename '/devices/pci0000:80/0000:80:02.0/0000:81:00.0/infiniband/qib0/ports/1/linkcontrol'
The patch below has two "linkcontrol" names causing the duplication.
Fix by using the correct "diag_counters" name on the second instance.
Fixes: 4a7aaf88c89f ("RDMA/qib: Use attributes for the port sysfs")
Link: https://lore.kernel.org/r/1645106372-23004-1-git-send-email-mike.marciniszyn@cornelisnetworks.com
Cc: <stable@vger.kernel.org>
Reviewed-by: Dennis Dalessandro <dennis.dalessandro@cornelisnetworks.com>
Signed-off-by: Mike Marciniszyn <mike.marciniszyn@cornelisnetworks.com>
Signed-off-by: Jason Gunthorpe <jgg@nvidia.com>
|
|
After slave abort, all DMA should be stopped, or it will affect the
next transmission and maybe abort again.
Signed-off-by: Jon Lin <jon.lin@rock-chips.com>
Link: https://lore.kernel.org/r/20220216014028.8123-3-jon.lin@rock-chips.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Get num-cs u32 from dts of_node property rather than u16.
Signed-off-by: Jon Lin <jon.lin@rock-chips.com>
Link: https://lore.kernel.org/r/20220216014028.8123-2-jon.lin@rock-chips.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
With the existing logic where clear_ack is true (HW doesn’t support
auto clear for ICR), interrupt clear register reset is not handled
properly. Due to this only the first interrupts get processed properly
and further interrupts are blocked due to not resetting interrupt
clear register.
Example for issue case where Invert_ack is false and clear_ack is true:
Say Default ISR=0x00 & ICR=0x00 and ISR is triggered with 2
interrupts making ISR = 0x11.
Step 1: Say ISR is set 0x11 (store status_buff = ISR). ISR needs to
be cleared with the help of ICR once the Interrupt is processed.
Step 2: Write ICR = 0x11 (status_buff), this will clear the ISR to 0x00.
Step 3: Issue - In the existing code, ICR is written with ICR =
~(status_buff) i.e ICR = 0xEE -> This will block all the interrupts
from raising except for interrupts 0 and 4. So expectation here is to
reset ICR, which will unblock all the interrupts.
if (chip->clear_ack) {
if (chip->ack_invert && !ret)
........
else if (!ret)
ret = regmap_write(map, reg,
~data->status_buf[i]);
So writing 0 and 0xff (when ack_invert is true) should have no effect, other
than clearing the ACKs just set.
Fixes: 3a6f0fb7b8eb ("regmap: irq: Add support to clear ack registers")
Signed-off-by: Prasad Kumpatla <quic_pkumpatl@quicinc.com>
Reviewed-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Tested-by: Marek Szyprowski <m.szyprowski@samsung.com>
Link: https://lore.kernel.org/r/20220217085007.30218-1-quic_pkumpatl@quicinc.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
When the gadget driver hasn't been (yet) configured, and the cable is
connected to a HOST, the SFTDISCON gets cleared unconditionally, so the
HOST tries to enumerate it.
At the host side, this can result in a stuck USB port or worse. When
getting lucky, some dmesg can be observed at the host side:
new high-speed USB device number ...
device descriptor read/64, error -110
Fix it in drd, by checking the enabled flag before calling
dwc2_hsotg_core_connect(). It will be called later, once configured,
by the normal flow:
- udc_bind_to_driver
- usb_gadget_connect
- dwc2_hsotg_pullup
- dwc2_hsotg_core_connect
Fixes: 17f934024e84 ("usb: dwc2: override PHY input signals with usb role switch support")
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Fabrice Gasnier <fabrice.gasnier@foss.st.com>
Link: https://lore.kernel.org/r/1644999135-13478-1-git-send-email-fabrice.gasnier@foss.st.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
When the Bay Trail phy GPIO mappings where added cs and reset were swapped,
this did not cause any issues sofar, because sofar they were always driven
high/low at the same time.
Note the new mapping has been verified both in /sys/kernel/debug/gpio
output on Android factory images on multiple devices, as well as in
the schematics for some devices.
Fixes: 5741022cbdf3 ("usb: dwc3: pci: Add GPIO lookup table on platforms without ACPI GPIO resources")
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Link: https://lore.kernel.org/r/20220213130524.18748-3-hdegoede@redhat.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
The interrupt mask is enabled before any potential failure points in
the driver, which can leave a failure path where we exit with
interrupts enabled but the device not live. This causes an infinite
stream of interrupts on an Apple M1 Pro laptop on USB-C.
Add a failure label that's used post enabling interrupts, where we
mask them again before returning an error.
Suggested-by: Sven Peter <sven@svenpeter.dev>
Cc: stable <stable@vger.kernel.org>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Link: https://lore.kernel.org/r/e6b80669-20f3-06e7-9ed5-8951a9c6db6f@kernel.dk
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Various block drivers call blk_set_queue_dying to mark a disk as dead due
to surprise removal events, but since commit 8e141f9eb803 that doesn't
work given that the GD_DEAD flag needs to be set to stop I/O.
Replace the driver calls to blk_set_queue_dying with a new (and properly
documented) blk_mark_disk_dead API, and fold blk_set_queue_dying into the
only remaining caller.
Fixes: 8e141f9eb803 ("block: drain file system I/O on del_gendisk")
Reported-by: Markus Blöchl <markus.bloechl@ipetronik.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Sagi Grimberg <sagi@grimberg.me>
Link: https://lore.kernel.org/r/20220217075231.1140-1-hch@lst.de
Signed-off-by: Jens Axboe <axboe@kernel.dk>
|
|
Add quirk CDC_MBIM_FLAG_AVOID_ALTSETTING_TOGGLE for Telit FN990
0x1071 composition in order to avoid bind error.
Signed-off-by: Daniele Palmas <dnlplm@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Commit 817b8b9c539 ("HID: elo: fix memory leak in elo_probe") introduced
memory leak on error path, but more importantly the whole USB reference
counting is not needed at all in the first place, as the driver itself
doesn't change the reference counting in any way, and the associated
usb_device is guaranteed to be kept around by USB core as long as the
driver binding exists.
Reported-by: Alan Stern <stern@rowland.harvard.edu>
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Fixes: fbf42729d0e ("HID: elo: update the reference count of the usb device structure")
Fixes: 817b8b9c539 ("HID: elo: fix memory leak in elo_probe")
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
|
|
https://gitlab.freedesktop.org/agd5f/linux into drm-fixes
amd-drm-fixes-5.17-2022-02-16:
amdgpu:
- Stable pstate clock fixes for Dimgrey Cavefish and Beige Goby
- S0ix SDMA fix
- Yellow Carp GPU reset fix
radeon:
- Backlight fix for iMac 12,1
Signed-off-by: Dave Airlie <airlied@redhat.com>
From: Alex Deucher <alexander.deucher@amd.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20220217035242.8084-1-alexander.deucher@amd.com
|
|
Sparse warns about the following cast in the function
falcon_copy_firmware_image() ...
drivers/gpu/drm/tegra/falcon.c:66:27: warning: cast to restricted __le32
Fix this by casting the firmware data array to __le32 instead of u32.
Signed-off-by: Jon Hunter <jonathanh@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
|
|
https://git.kernel.org/pub/scm/linux/kernel/git/chunkuang.hu/linux into drm-fixes
Mediatek DRM Fixes for Linux 5.17
1. Avoid EPROBE_DEFER loop with external bridge
Signed-off-by: Dave Airlie <airlied@redhat.com>
From: Chun-Kuang Hu <chunkuang.hu@kernel.org>
Link: https://patchwork.freedesktop.org/patch/msgid/1645027727-19554-1-git-send-email-chunkuang.hu@kernel.org
|
|
of_node_put(priv->ds->slave_mii_bus->dev.of_node) should be
done before mdiobus_free(priv->ds->slave_mii_bus).
Signed-off-by: Alexey Khoroshilov <khoroshilov@ispras.ru>
Fixes: 0d120dfb5d67 ("net: dsa: lantiq_gswip: don't use devres for mdiobus")
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://lore.kernel.org/r/1644921768-26477-1-git-send-email-khoroshilov@ispras.ru
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/ulfh/mmc
Pull MMC fix from Ulf Hansson:
"Fix recovery logic for multi block I/O reads (MMC_READ_MULTIPLE_BLOCK)"
* tag 'mmc-v5.17-rc1-2' of git://git.kernel.org/pub/scm/linux/kernel/git/ulfh/mmc:
mmc: block: fix read single on recovery logic
|
|
Daniel Gibson reports that the n_tty code gets line termination wrong in
very specific cases:
"If you feed a line with exactly 64 chars + terminating newline, and
directly afterwards (without reading) another line into a pseudo
terminal, the the first read() on the other side will return the 64
char line *without* terminating newline, and the next read() will
return the missing terminating newline AND the complete next line (if
it fits in the buffer)"
and bisected the behavior to commit 3b830a9c34d5 ("tty: convert
tty_ldisc_ops 'read()' function to take a kernel pointer").
Now, digging deeper, it turns out that the behavior isn't exactly new:
what changed in commit 3b830a9c34d5 was that the tty line discipline
.read() function is now passed an intermediate kernel buffer rather than
the final user space buffer.
And that intermediate kernel buffer is 64 bytes in size - thus that
special case with exactly 64 bytes plus terminating newline.
The same problem did exist before, but historically the boundary was not
the 64-byte chunk, but the user-supplied buffer size, which is obviously
generally bigger (and potentially bigger than N_TTY_BUF_SIZE, which
would hide the issue entirely).
The reason is that the n_tty canon_copy_from_read_buf() code would look
ahead for the EOL character one byte further than it would actually
copy. It would then decide that it had found the terminator, and unmark
it as an EOL character - which in turn explains why the next read
wouldn't then be terminated by it.
Now, the reason it did all this in the first place is related to some
historical and pretty obscure EOF behavior, see commit ac8f3bf8832a
("n_tty: Fix poll() after buffer-limited eof push read") and commit
40d5e0905a03 ("n_tty: Fix EOF push handling").
And the reason for the EOL confusion is that we treat EOF as a special
EOL condition, with the EOL character being NUL (aka "__DISABLED_CHAR"
in the kernel sources).
So that EOF look-ahead also affects the normal EOL handling.
This patch just removes the look-ahead that causes problems, because EOL
is much more critical than the historical "EOF in the middle of a line
that coincides with the end of the buffer" handling ever was.
Now, it is possible that we should indeed re-introduce the "look at next
character to see if it's a EOF" behavior, but if so, that should be done
not at the kernel buffer chunk boundary in canon_copy_from_read_buf(),
but at a higher level, when we run out of the user buffer.
In particular, the place to do that would be at the top of
'n_tty_read()', where we check if it's a continuation of a previously
started read, and there is no more buffer space left, we could decide to
just eat the __DISABLED_CHAR at that point.
But that would be a separate patch, because I suspect nobody actually
cares, and I'd like to get a report about it before bothering.
Fixes: 3b830a9c34d5 ("tty: convert tty_ldisc_ops 'read()' function to take a kernel pointer")
Fixes: ac8f3bf8832a ("n_tty: Fix poll() after buffer-limited eof push read")
Fixes: 40d5e0905a03 ("n_tty: Fix EOF push handling")
Link: https://bugzilla.kernel.org/show_bug.cgi?id=215611
Reported-and-tested-by: Daniel Gibson <metalcaedes@gmail.com>
Cc: Peter Hurley <peter@hurleysoftware.com>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Jiri Slaby <jirislaby@kernel.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Add and ACPI idle power level limit for 32-bit ThinkPad T40.
There is a regression on T40 introduced by commit d6b88ce2, starting
with kernel 5.16:
commit d6b88ce2eb9d2698eb24451eb92c0a1649b17bb1
Author: Richard Gong <richard.gong@amd.com>
Date: Wed Sep 22 08:31:16 2021 -0500
ACPI: processor idle: Allow playing dead in C3 state
The above patch is trying to enter C3 state during init, what is causing
a T40 system freeze. I have not found a similar issue on any other of my
32-bit machines.
The fix is to add another exception to the processor_power_dmi_table[] list.
As a result the dmesg shows as expected:
[2.155398] ACPI: IBM ThinkPad T40 detected - limiting to C2 max_cstate. Override with "processor.max_cstate=9"
[2.155404] ACPI: processor limited to max C-state 2
The fix is trivial and affects only vintage T40 systems.
Fixes: d6b88ce2eb9d ("CPI: processor idle: Allow playing dead in C3 state")
Signed-off-by: Woody Suwalski <wsuwalski@gmail.com>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Cc: 5.16+ <stable@vger.kernel.org> # 5.16+
[ rjw: New subject ]
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
The new TegraDRM UAPI uses syncpoint waiting with timeout set to
zero to indicate reading the syncpoint value. To support that we
need to return the syncpoint value always when waiting.
Fixes: 44e961381354 ("drm/tegra: Implement syncpoint wait UAPI")
Signed-off-by: Mikko Perttunen <mperttunen@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
|
|
Different add ons to the wheel base report different models. Having
no wheel mounted to the base and using the open wheel attachment is
added here.
Signed-off-by: Michael Hübner <michaelh.95@t-online.de>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
|
|
As of logitech lightspeed receiver fw version 04.02.B0009,
HIDPP_PARAM_DEVICE_INFO is being reported as 0x11.
With patch "HID: logitech-dj: add support for the new lightspeed receiver
iteration", the mouse starts to error out with:
logitech-djreceiver: unusable device of type UNKNOWN (0x011) connected on
slot 1
and becomes unusable.
This has been noticed on a Logitech G Pro X Superlight fw MPM 25.01.B0018.
Signed-off-by: Lucas Zampieri <lzampier@redhat.com>
Acked-by: Nestor Lopez Casado <nlopezcasad@logitech.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
|
|
With v2 hardware, an IRQ can be configured to trigger on both edges via
a bit in the int_bothedge register. Currently, the driver sets this bit
when changing the trigger type to IRQ_TYPE_EDGE_BOTH, but fails to reset
this bit if the trigger type is later changed to something else. This
causes spurious IRQs, and when using gpio-keys with wakeup-event-action
set to EV_ACT_(DE)ASSERTED, those IRQs translate into spurious wakeups.
Fixes: 3bcbd1a85b68 ("gpio/rockchip: support next version gpio controller")
Reported-by: Guillaume Savaton <guillaume@baierouge.fr>
Tested-by: Guillaume Savaton <guillaume@baierouge.fr>
Signed-off-by: Samuel Holland <samuel@sholland.org>
Signed-off-by: Bartosz Golaszewski <brgl@bgdev.pl>
|
|
Make sure we don't assign an error pointer to crtc_state->mode_blob
as that will break all kinds of places that assume either NULL or a
valid pointer (eg. drm_property_blob_put()).
Cc: stable@vger.kernel.org
Reported-by: fuyufan <fuyufan@huawei.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20220209091928.14766-1-ville.syrjala@linux.intel.com
Acked-by: Maxime Ripard <maxime@cerno.tech>
|
|
This driver works just fine with the BT404 version of the touchscreen
as well. Tested on the Samsung GT-I8160 (Codina) mobile phone.
Add all the new variants from the binding document so people can
easily test them, we believe most of them work more or less.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Link: https://lore.kernel.org/r/20220214234033.1052681-1-linus.walleij@linaro.org
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
|
|
Paul reports that the ACPI core complains on every boot about a missing
CEDT table. Unlike the standard NUMA tables (SRAT, MADT, and SLIT) that
are critical to NUMA init, CEDT is only expected on CXL platforms. Given
the notice is not actionable lower its severity to debug.
Link: https://lore.kernel.org/r/55f5c077-061c-7e53-b02d-53dde1dd654f@molgen.mpg.de
Fixes: fd49f99c1809 ("ACPI: NUMA: Add a node and memblk for each CFMWS not in SRAT")
Reported-by: Paul Menzel <pmenzel@molgen.mpg.de>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/hid/hid
Pull HID fixes from Jiri Kosina:
- memory leak fix for hid-elo driver (Dongliang Mu)
- fix for hangs on newer AMD platforms with amd_sfh-driven hardware
(Basavaraj Natikar )
- locking fix in i2c-hid (Daniel Thompson)
- a few device-ID specific quirks
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/hid/hid:
HID: amd_sfh: Add interrupt handler to process interrupts
HID: amd_sfh: Add functionality to clear interrupts
HID: amd_sfh: Disable the interrupt for all command
HID: amd_sfh: Correct the structure field name
HID: amd_sfh: Handle amd_sfh work buffer in PM ops
HID:Add support for UGTABLET WP5540
HID: amd_sfh: Add illuminance mask to limit ALS max value
HID: amd_sfh: Increase sensor command timeout
HID: i2c-hid: goodix: Fix a lockdep splat
HID: elo: fix memory leak in elo_probe
HID: apple: Set the tilde quirk flag on the Wellspring 5 and later
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/deller/parisc-linux
Pull parisc architecture fixes from Helge Deller:
- Fix miscompilations when function calls are made from inside a
put_user() call
- Drop __init from map_pages() declaration to avoid random boot crashes
- Added #error messages if a 64-bit compiler was used to build a 32-bit
kernel (and vice versa)
- Fix out-of-bound data TLB miss faults in sba_iommu and ccio-dma
drivers
- Add ioread64_lo_hi() and iowrite64_lo_hi() functions to avoid kernel
test robot errors
- Fix link failure when 8250_gsc driver is built without CONFIG_IOSAPIC
* tag 'for-5.17/parisc-3' of git://git.kernel.org/pub/scm/linux/kernel/git/deller/parisc-linux:
serial: parisc: GSC: fix build when IOSAPIC is not set
parisc: Fix some apparent put_user() failures
parisc: Show error if wrong 32/64-bit compiler is being used
parisc: Add ioread64_lo_hi() and iowrite64_lo_hi()
parisc: Fix sglist access in ccio-dma.c
parisc: Fix data TLB miss in sba_unmap_sg
parisc: Drop __init from map_pages declaration
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/hyperv/linux
Pull hyperv fixes from Wei Liu:
- Rework use of DMA_BIT_MASK in vmbus to work around a clang bug
(Michael Kelley)
- Fix NUMA topology (Long Li)
- Fix a memory leak in vmbus (Miaoqian Lin)
- One minor clean-up patch (Cai Huoqing)
* tag 'hyperv-fixes-signed-20220215' of git://git.kernel.org/pub/scm/linux/kernel/git/hyperv/linux:
Drivers: hv: utils: Make use of the helper macro LIST_HEAD()
Drivers: hv: vmbus: Rework use of DMA_BIT_MASK(64)
Drivers: hv: vmbus: Fix memory leak in vmbus_add_channel_kobj
PCI: hv: Fix NUMA node assignment when kernel boots with custom NUMA topology
|
|
It appears that last minute change moved ACPI ID of Alder Lake-M
to the INTC1055, which is already in the driver.
This ID on the other hand will be used elsewhere.
This reverts commit 258435a1c8187f559549e515d2f77fa0b57bcd27.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
|
|
In rare cases the display is flipped or mirrored. This was observed more
often in a low temperature environment. A clean reset on init_display()
should help to get registers in a sane state.
Fixes: ef8f317795da (staging: fbtft: use init function instead of init sequence)
Cc: stable@vger.kernel.org
Signed-off-by: Oliver Graute <oliver.graute@kococonnector.com>
Link: https://lore.kernel.org/r/20220210085322.15676-1-oliver.graute@kococonnector.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
A broken device may give an extreme offset like 0xFFF0
and a reasonable length for a fragment. In the sanity
check as formulated now, this will create an integer
overflow, defeating the sanity check. Both offset
and offset + len need to be checked in such a manner
that no overflow can occur.
And those quantities should be unsigned.
Signed-off-by: Oliver Neukum <oneukum@suse.com>
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Do alignment logic properly and use the "ptr" local variable for
calculating the remainder of the alignment.
This became an issue because struct edac_mc_layer has a size that is not
zero modulo eight, and the next offset that was prepared for the private
data was unaligned, causing an alignment exception.
The patch in Fixes: which broke this actually wanted to "what we
actually care about is the alignment of the actual pointer that's about
to be returned." But it didn't check that alignment.
Use the correct variable "ptr" for that.
[ bp: Massage commit message. ]
Fixes: 8447c4d15e35 ("edac: Do alignment logic properly in edac_align_ptr()")
Signed-off-by: Eliav Farber <farbere@amazon.com>
Signed-off-by: Borislav Petkov <bp@suse.de>
Cc: <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20220113100622.12783-2-farbere@amazon.com
|
