| Age | Commit message (Collapse) | Author |
|---|
|
Navi12 HDCP & DTM deinitialization needs continue to free bo if already
created though initialized flag is not set.
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Jiawei Gu <Jiawei.Gu@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
Some of the newly added code is hidden inside of #ifdef
blocks, but one variable is unused when debugfs is disabled:
drivers/gpu/drm/amd/amdgpu/../display/amdgpu_dm/amdgpu_dm.c:8370:8: error: unused variable 'configure_crc' [-Werror,-Wunused-variable]
Change the #ifdef to an if(IS_ENABLED()) check to fix the warning
and avoid adding more #ifdefs.
Fixes: c920888c604d ("drm/amd/display: Expose new CRC window property")
Reviewed-by: Wayne Lin <Wayne.Lin@amd.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
This patch is to improve the fine grain tuning function for RV/RV2/PCO.
The fine grain tuning function uses the sysfs node -- pp_od_clk_voltage
to config gfxclk. Meanwhile, another sysfs
node -- power_dpm_force_perfomance_level also affects the gfx clk.
It will cause confusion when these two sysfs nodes works
together. So this patch adds one flag to avoid this confusion, the flag
will make these two sysfs nodes work separately.
The flag is set as "disabled" by default, so the fine grain tuning function
will be disabled by default.
Only when power_dpm_force_perfomance_level is changed to
"manual" mode, the flag will be set as "enabled",
and the fine grain tuning function will be enabled.
In other profile modes, including "auto", "high", "low",
"profile_peak", "profile_standard", "profile_min_sclk",
"profile_min_mclk", the flag will be set as "disabled",
and the od range of fine grain tuning function will
be restored default value.
Signed-off-by: Xiaojian Du <Xiaojian.Du@amd.com>
Reviewed-by: Huang Rui <ray.huang@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
This patch is to fix the failure when change power profile to
"profile_peak" for renoir.
Signed-off-by: Xiaojian Du <Xiaojian.Du@amd.com>
Reviewed-by: Huang Rui <ray.huang@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
When GFXOFF is enabled and GPU is idle, driver will fail to access some
registers. Therefore change to disable power gating before all access
registers with MMIO.
Dmesg log is as following:
amdgpu 0000:03:00.0: amdgpu: amdgpu: finishing device.
amdgpu: cp queue pipe 4 queue 0 preemption failed
amdgpu 0000:03:00.0: amdgpu: failed to write reg 2890 wait reg 28a2
amdgpu 0000:03:00.0: amdgpu: failed to write reg 1a6f4 wait reg 1a706
amdgpu 0000:03:00.0: amdgpu: failed to write reg 2890 wait reg 28a2
amdgpu 0000:03:00.0: amdgpu: failed to write reg 1a6f4 wait reg 1a706
Signed-off-by: Dennis Li <Dennis.Li@amd.com>
Reviewed-by: Hawking Zhang <Hawking.Zhang@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
ASD and TA share the same firmware in SIENNA_CICHLID and only TA
firmware is requested during boot, so only need release TA firmware when
remove device.
[ 83.877150] general protection fault, probably for non-canonical address 0x1269f97e6ed04095: 0000 [#1] SMP PTI
[ 83.888076] CPU: 0 PID: 1312 Comm: modprobe Tainted: G W OE 5.9.0-rc5-deli-amd-vangogh-0.0.6.6-114-gdd99d5669a96-dirty #2
[ 83.901160] Hardware name: System manufacturer System Product Name/TUF Z370-PLUS GAMING II, BIOS 0411 09/21/2018
[ 83.912353] RIP: 0010:free_fw_priv+0xc/0x120
[ 83.917531] Code: e8 99 cd b0 ff b8 a1 ff ff ff eb 9f 4c 89 f7 e8 8a cd b0 ff b8 f4 ff ff ff eb 90 0f 1f 00 0f 1f 44 00 00 55 48 89 e5 41 54 53 <4c> 8b 67 18 48 89 fb 4c 89 e7 e8 45 94 41 00 b8 ff ff ff ff f0 0f
[ 83.937576] RSP: 0018:ffffbc34c13a3ce0 EFLAGS: 00010206
[ 83.943699] RAX: ffffffffbb681850 RBX: ffffa047f117eb60 RCX: 0000000080800055
[ 83.951879] RDX: ffffbc34c1d5f000 RSI: 0000000080800055 RDI: 1269f97e6ed04095
[ 83.959955] RBP: ffffbc34c13a3cf0 R08: 0000000000000000 R09: 0000000000000001
[ 83.968107] R10: ffffbc34c13a3cc8 R11: 00000000ffffff00 R12: ffffa047d6b23378
[ 83.976166] R13: ffffa047d6b23338 R14: ffffa047d6b240c8 R15: 0000000000000000
[ 83.984295] FS: 00007f74f6712540(0000) GS:ffffa047fbe00000(0000) knlGS:0000000000000000
[ 83.993323] CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033
[ 84.000056] CR2: 0000556a1cca4e18 CR3: 000000021faa8004 CR4: 00000000003706f0
[ 84.008128] DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000
[ 84.016155] DR3: 0000000000000000 DR6: 00000000fffe0ff0 DR7: 0000000000000400
[ 84.024174] Call Trace:
[ 84.027514] release_firmware.part.11+0x4b/0x70
[ 84.033017] release_firmware+0x13/0x20
[ 84.037803] psp_sw_fini+0x77/0xb0 [amdgpu]
[ 84.042857] amdgpu_device_fini+0x38c/0x5d0 [amdgpu]
[ 84.048815] amdgpu_driver_unload_kms+0x43/0x70 [amdgpu]
[ 84.055055] drm_dev_unregister+0x73/0xb0 [drm]
[ 84.060499] drm_dev_unplug+0x28/0x30 [drm]
[ 84.065598] amdgpu_dev_uninit+0x1b/0x40 [amdgpu]
[ 84.071223] amdgpu_pci_remove+0x4e/0x70 [amdgpu]
[ 84.076835] pci_device_remove+0x3e/0xc0
[ 84.081609] device_release_driver_internal+0xfb/0x1c0
[ 84.087558] driver_detach+0x4d/0xa0
[ 84.092041] bus_remove_driver+0x5f/0xe0
[ 84.096854] driver_unregister+0x2f/0x50
[ 84.101594] pci_unregister_driver+0x22/0xa0
[ 84.106806] amdgpu_exit+0x15/0x2b [amdgpu]
Signed-off-by: Dennis Li <Dennis.Li@amd.com>
Reviewed-by: Hawking Zhang <Hawking.Zhang@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
global noretry setting is cached to gmc.noretry
Signed-off-by: Hawking Zhang <Hawking.Zhang@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
fix NULL pointer issue when read sysfs amdgpu_current_backlight_pwm sysfs node.
Call Trace:
[ 248.273833] BUG: kernel NULL pointer dereference, address: 0000000000000130
[ 248.273930] #PF: supervisor read access in kernel mode
[ 248.273993] #PF: error_code(0x0000) - not-present page
[ 248.274054] PGD 0 P4D 0
[ 248.274092] Oops: 0000 [#1] SMP PTI
[ 248.274138] CPU: 2 PID: 1377 Comm: cat Tainted: G OE 5.9.0-rc5-drm-next-5.9+ #1
[ 248.274233] Hardware name: System manufacturer System Product Name/Z170-A, BIOS 3802 03/15/2018
[ 248.274641] RIP: 0010:dc_link_get_backlight_level+0x5/0x70 [amdgpu]
[ 248.274718] Code: 67 ff ff ff 41 b9 03 00 00 00 e9 45 ff ff ff d1 ea e9 55 ff ff ff 0f 1f 44 00 00 66 2e
0f 1f 84 00 00 00 00 00 0f 1f 44 00 00 <48> 8b 87 30 01 00 00 48 8b 00 48 8b 88 88 03 00 00 48 8d 81 e8 01
[ 248.274919] RSP: 0018:ffffb5ad809b3df0 EFLAGS: 00010203
[ 248.274982] RAX: ffffa0f77d1c0010 RBX: ffffa0f793ae9168 RCX: 0000000000000001
[ 248.275064] RDX: ffffa0f79753db00 RSI: 0000000000000001 RDI: 0000000000000000
[ 248.275145] RBP: ffffb5ad809b3e00 R08: ffffb5ad809b3da0 R09: 0000000000000000
[ 248.275225] R10: ffffb5ad809b3e68 R11: 0000000000000000 R12: ffffa0f793ae9190
[ 248.275306] R13: ffffb5ad809b3ef0 R14: 0000000000000001 R15: ffffa0f793ae9168
[ 248.275388] FS: 00007f5f1ec4d540(0000) GS:ffffa0f79ec80000(0000) knlGS:0000000000000000
[ 248.275480] CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033
[ 248.275547] CR2: 0000000000000130 CR3: 000000042a03c005 CR4: 00000000003706e0
[ 248.275628] DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000
[ 248.275708] DR3: 0000000000000000 DR6: 00000000fffe0ff0 DR7: 0000000000000400
[ 248.275789] Call Trace:
[ 248.276124] ? current_backlight_read+0x24/0x40 [amdgpu]
[ 248.276194] seq_read+0xc3/0x3f0
[ 248.276240] full_proxy_read+0x5c/0x90
[ 248.276290] vfs_read+0xa7/0x190
[ 248.276334] ksys_read+0xa7/0xe0
[ 248.276379] __x64_sys_read+0x1a/0x20
[ 248.276429] do_syscall_64+0x37/0x80
[ 248.276477] entry_SYSCALL_64_after_hwframe+0x44/0xa9
[ 248.276538] RIP: 0033:0x7f5f1e75c191
[ 248.276585] Code: fe ff ff 48 8d 3d b7 9d 0a 00 48 83 ec 08 e8 46 4d 02 00 66 0f 1f 44 00 00 48 8d 05 71 07
2e 00 8b 00 85 c0 75 13 31 c0 0f 05 <48> 3d 00 f0 ff ff 77 57 f3 c3 0f 1f 44 00 00 41 54 55 49 89 d4 53Hw
[ 248.276784] RSP: 002b:00007ffcb1fc3f38 EFLAGS: 00000246 ORIG_RAX: 0000000000000000
[ 248.276872] RAX: ffffffffffffffda RBX: 0000000000020000 RCX: 00007f5f1e75c191
[ 248.276953] RDX: 0000000000020000 RSI: 00007f5f1ec2b000 RDI: 0000000000000003
[ 248.277034] RBP: 0000000000020000 R08: 00000000ffffffff R09: 0000000000000000
[ 248.277115] R10: 0000000000000022 R11: 0000000000000246 R12: 00007f5f1ec2b000
[ 248.277195] R13: 0000000000000003 R14: 00007f5f1ec2b00f R15: 0000000000020000
[ 248.277279] Modules linked in: amdgpu(OE) iommu_v2 gpu_sched ttm(OE) drm_kms_helper cec drm
i2c_algo_bit fb_sys_fops syscopyarea sysfillrect sysimgblt rpcsec_gss_krb5 auth_rpcgss nfsv4 nfs
lockd grace fscache nls_iso8859_1 snd_hda_codec_realtek snd_hda_codec_hdmi snd_hda_codec_generic
ledtrig_audio intel_rapl_msr intel_rapl_common snd_hda_intel snd_intel_dspcfg x86_pkg_temp_thermal
intel_powerclamp snd_hda_codec snd_hda_core snd_hwdep snd_pcm snd_seq_midi snd_seq_midi_event mei_hdcp
coretemp snd_rawmidi snd_seq kvm_intel kvm snd_seq_device snd_timer irqbypass joydev snd input_leds soundcore
crct10dif_pclmul crc32_pclmul ghash_clmulni_intel aesni_intel crypto_simd cryptd glue_helper rapl intel_cstate
mac_hid mei_me serio_raw mei eeepc_wmi wmi_bmof asus_wmi mxm_wmi intel_wmi_thunderbolt acpi_pad sparse_keymap
efi_pstore sch_fq_codel parport_pc ppdev lp parport sunrpc ip_tables x_tables autofs4 hid_logitech_hidpp
hid_logitech_dj hid_generic usbhid hid e1000e psmouse ahci libahci wmi video
[ 248.278211] CR2: 0000000000000130
[ 248.278221] ---[ end trace 1fbe72fe6f91091d ]---
[ 248.357226] RIP: 0010:dc_link_get_backlight_level+0x5/0x70 [amdgpu]
[ 248.357272] Code: 67 ff ff ff 41 b9 03 00 00 00 e9 45 ff ff ff d1 ea e9 55 ff ff ff 0f 1f 44 00 00 66 2e 0f 1f 84 00 00 00 00 00 0f 1f 44 00 00 <48> 8b 87 30 01 00 00 48 8b 00 48 8b 88 88 03 00 00 48 8d 81 e8 01
Signed-off-by: Kevin Wang <kevin1.wang@amd.com>
Acked-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
sienna cichlid interfaces with RAS eeprom on I2C controller port 1
Reviewed-by: Hawking Zhang <Hawking.Zhang@amd.com>
Signed-off-by: John Clements <john.clements@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
This patch is to improve the fine grain tuning function for RV/RV2/PCO.
This patch adds two new commands: "restore" and "commit".
This function uses the pp_od_clk_voltage sysfs file to configure the min
and max value of gfx clock frequency manually or restore the default value.
Command guide:
echo "s level value" > pp_od_clk_voltage
"s" - set the sclk frequency
"level" - 0 or 1, "0" represents the min value, "1" represents
the max value
"value" - the target value of sclk frequency, it should be limited in the
safe range
echo "r" > pp_od_clk_voltage
"r" - reset the sclk frequency, restore the default value instantly
echo "c" > pp_od_clk_voltage
"c" - commit the min and max value of sclk frequency to the system
only after the commit command, the target values set by "s" command
will take effect.
Example:
1)change power profile from "auto" to "manual"
$ cat power_dpm_force_performance_level
auto
$ echo "manual" > power_dpm_force_performance_level
$ cat power_dpm_force_performance_level
manual
2)check the default sclk frequency
$ cat pp_od_clk_voltage
OD_SCLK:
0: 200Mhz
1: 1400Mhz
OD_RANGE:
SCLK: 200MHz 1400MHz
3)use "s" -- set command to configure the min and max sclk frequency
$ echo "s 0 600" > pp_od_clk_voltage
$ echo "s 1 1000" > pp_od_clk_voltage
$ echo "c" > pp_od_clk_voltage
$ cat pp_od_clk_voltage
OD_SCLK:
0: 600Mhz
1: 1000Mhz
OD_RANGE:
SCLK: 200MHz 1400MHz
4)use "r" -- reset command to restore the min or max sclk frequency
$ echo "r" > pp_od_clk_voltage
$ cat pp_od_clk_voltage
OD_SCLK:
0: 200Mhz
1: 1400Mhz
OD_RANGE:
SCLK: 200MHz 1400MHz
Signed-off-by: Xiaojian Du <Xiaojian.Du@amd.com>
Reviewed-by: Evan Quan <evan.quan@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
This patch is to correct the sensor value of power for vangogh.
Signed-off-by: Xiaojian Du <Xiaojian.Du@amd.com>
Reviewed-by: Evan Quan <evan.quan@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/djakov/icc into char-misc-linus
Georgi writes:
interconnect fixes for v5.11
This contains a few fixes for iMX and Qualcomm drivers and also
updates my email to my kernel.org address.
- qcom: Fix rpmh link failures when compile test is enabled
- imx: Add a missing of_node_put after of_device_is_available
- imx: Remove a useless test
- imx8mq: Use icc_sync_state
Signed-off-by: Georgi Djakov <georgi.djakov@linaro.org>
* tag 'icc-5.11-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/djakov/icc:
MAINTAINERS: Update Georgi's email address
interconnect: imx8mq: Use icc_sync_state
interconnect: imx: Remove a useless test
interconnect: imx: Add a missing of_node_put after of_device_is_available
interconnect: qcom: fix rpmh link failures
|
|
https://git.kernel.org/pub/scm/linux/kernel/git/johan/usb-serial into usb-linus
Johan writes:
USB-serial fixes for 5.11-rc3
Here's a fix for a DMA-from-stack issue in iuu_phoenix and a couple of
new modem device ids.
All have been in linux-next with no reported issues.
* tag 'usb-serial-5.11-rc3' of https://git.kernel.org/pub/scm/linux/kernel/git/johan/usb-serial:
USB: serial: iuu_phoenix: fix DMA from stack
USB: serial: option: add LongSung M5710 module support
USB: serial: option: add Quectel EM160R-GL
|
|
With commit e722a295cf49 ("staging: ion: remove from the tree"), ION and
its corresponding config CONFIG_ION is gone. Remove stale references
from drivers/staging/media/atomisp/pci and from the recommended Android
kernel config.
Fixes: e722a295cf49 ("staging: ion: remove from the tree")
Cc: Hridya Valsaraju <hridya@google.com>
Cc: Rob Herring <robh@kernel.org>
Cc: linux-media@vger.kernel.org
Cc: devel@driverdev.osuosl.org
Signed-off-by: Matthias Maennich <maennich@google.com>
Link: https://lore.kernel.org/r/20210106155201.2845319-1-maennich@google.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
The only used argument in this function is the "req".
Signed-off-by: Max Gurtovoy <mgurtovoy@nvidia.com>
Reviewed-by: Minwoo Im <minwoo.im.dev@gmail.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
|
|
When a queue is in NVMET_RDMA_Q_CONNECTING state, it may has some
requests at rsp_wait_list. In case a disconnect occurs at this
state, no one will empty this list and will return the requests to
free_rsps list. Normally nvmet_rdma_queue_established() free those
requests after moving the queue to NVMET_RDMA_Q_LIVE state, but in
this case __nvmet_rdma_queue_disconnect() is called before. The
crash happens at nvmet_rdma_free_rsps() when calling
list_del(&rsp->free_list), because the request exists only at
the wait list. To fix the issue, simply clear rsp_wait_list when
destroying the queue.
Signed-off-by: Israel Rukshin <israelr@nvidia.com>
Reviewed-by: Max Gurtovoy <mgurtovoy@nvidia.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
|
|
There are no callers for nvme_reset_ctrl_sync() and
nvme_alloc_request_qid() so that we keep the symbols exported.
Unexport those functions, mark them static and update the header file
respectively.
Signed-off-by: Minwoo Im <minwoo.im.dev@gmail.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
|
|
While handling the completion queue, keep a local copy of the command id
from the DMA-accessible completion entry. This silences a time-of-check
to time-of-use (TOCTOU) warning from KF/x[1], with respect to a
Thunderclap[2] vulnerability analysis. The double-read impact appears
benign.
There may be a theoretical window for @command_id to be used as an
adversary-controlled array-index-value for mounting a speculative
execution attack, but that mitigation is saved for a potential follow-on.
A man-in-the-middle attack on the data payload is out of scope for this
analysis and is hopefully mitigated by filesystem integrity mechanisms.
[1] https://github.com/intel/kernel-fuzzer-for-xen-project
[2] http://thunderclap.io/thunderclap-paper-ndss2019.pdf
Signed-off-by: Lalithambika Krishna Kumar <lalithambika.krishnakumar@intel.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
|
|
We may send a request (with or without its data) from two paths:
1. From our I/O context nvme_tcp_io_work which is triggered from:
- queue_rq
- r2t reception
- socket data_ready and write_space callbacks
2. Directly from queue_rq if the send_list is empty (because we want to
save the context switch associated with scheduling our io_work).
However, given that now we have the send_mutex, we may run into a race
condition where none of these contexts will send the pending payload to
the controller. Both io_work send path and queue_rq send path
opportunistically attempt to acquire the send_mutex however queue_rq only
attempts to send a single request, and if io_work context fails to
acquire the send_mutex it will complete without rescheduling itself.
The race can trigger with the following sequence:
1. queue_rq sends request (no incapsule data) and blocks
2. RX path receives r2t - prepares data PDU to send, adds h2cdata PDU
to the send_list and schedules io_work
3. io_work triggers and cannot acquire the send_mutex - because of (1),
ends without self rescheduling
4. queue_rq completes the send, and completes
==> no context will send the h2cdata - timeout.
Fix this by having queue_rq sending as much as it can from the send_list
such that if it still has any left, its because the socket buffer is
full and the socket write_space callback will trigger, thus guaranteeing
that a context will be scheduled to send the h2cdata PDU.
Fixes: db5ad6b7f8cd ("nvme-tcp: try to send request in queue_rq context")
Reported-by: Potnuri Bharat Teja <bharat@chelsio.com>
Reported-by: Samuel Jones <sjones@kalrayinc.com>
Signed-off-by: Sagi Grimberg <sagi@grimberg.me>
Tested-by: Potnuri Bharat Teja <bharat@chelsio.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
|
|
A system with more than one of these SSDs will only have one usable.
Hence the kernel fails to detect nvme devices due to duplicate cntlids.
[ 6.274554] nvme nvme1: Duplicate cntlid 33 with nvme0, rejecting
[ 6.274566] nvme nvme1: Removing after probe failure status: -22
Adding the NVME_QUIRK_IGNORE_DEV_SUBNQN quirk to resolves the issue.
Signed-off-by: Gopal Tiwari <gtiwari@redhat.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
|
|
Kernel robot had the following warnings:
>> fcloop.c:1506:6: warning: %x in format string (no. 1) requires
>> 'unsigned int *' but the argument type is 'signed int *'.
>> [invalidScanfArgType_int]
>> if (sscanf(buf, "%x:%d:%d", &opcode, &starting, &amount) != 3)
>> ^
Resolve by changing opcode from and int to an unsigned int
and
>> fcloop.c:1632:32: warning: Uninitialized variable: lport [uninitvar]
>> ret = __wait_localport_unreg(lport);
>> ^
>> fcloop.c:1615:28: warning: Uninitialized variable: nport [uninitvar]
>> ret = __remoteport_unreg(nport, rport);
>> ^
These aren't actual issues as the values are assigned prior to use.
It appears the tool doesn't understand list_first_entry_or_null().
Regardless, quiet the tool by initializing the pointers to NULL at
declaration.
Signed-off-by: James Smart <james.smart@broadcom.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
|
|
Recent patches changed calling sequences. nvme_fc_abort_outstanding_ios
used to be called from a timeout or work context. Now it is being called
in an io completion context, which can be an interrupt handler.
Unfortunately, the abort outstanding ios routine attempts to stop nvme
queues and nested routines that may try to sleep, which is in conflict
with the interrupt handler.
Correct replacing the direct call with a work element scheduling, and the
abort outstanding ios routine will be called in the work element.
Fixes: 95ced8a2c72d ("nvme-fc: eliminate terminate_io use by nvme_fc_error_recovery")
Signed-off-by: James Smart <james.smart@broadcom.com>
Reported-by: Daniel Wagner <dwagner@suse.de>
Tested-by: Daniel Wagner <dwagner@suse.de>
Signed-off-by: Christoph Hellwig <hch@lst.de>
|
|
Since commit 1d6cd3929360 ("modpost: turn missing MODULE_LICENSE()
into error") the ppc32_allmodconfig build fails with:
ERROR: modpost: missing MODULE_LICENSE() in drivers/net/ethernet/freescale/fs_enet/mii-fec.o
ERROR: modpost: missing MODULE_LICENSE() in drivers/net/ethernet/freescale/fs_enet/mii-bitbang.o
Add the missing MODULE_LICENSEs to fix the build. Both files include a
copyright header indicating they are GPL v2.
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Aligning to tx_ndp_modulus is not sufficient because the next align
call can be cdc_ncm_align_tail, which can add up to ctx->tx_modulus +
ctx->tx_remainder - 1 bytes. This used to lead to occasional crashes
on a Huawei 909s-120 LTE module as follows:
- the condition marked /* if there is a remaining skb [...] */ is true
so the swaps happen
- skb_out is set from ctx->tx_curr_skb
- skb_out->len is exactly 0x3f52
- ctx->tx_curr_size is 0x4000 and delayed_ndp_size is 0xac
(note that the sum of skb_out->len and delayed_ndp_size is 0x3ffe)
- the for loop over n is executed once
- the cdc_ncm_align_tail call marked /* align beginning of next frame */
increases skb_out->len to 0x3f56 (the sum is now 0x4002)
- the condition marked /* check if we had enough room left [...] */ is
false so we break out of the loop
- the condition marked /* If requested, put NDP at end of frame. */ is
true so the NDP is written into skb_out
- now skb_out->len is 0x4002, so padding_count is minus two interpreted
as an unsigned number, which is used as the length argument to memset,
leading to a crash with various symptoms but usually including
> Call Trace:
> <IRQ>
> cdc_ncm_fill_tx_frame+0x83a/0x970 [cdc_ncm]
> cdc_mbim_tx_fixup+0x1d9/0x240 [cdc_mbim]
> usbnet_start_xmit+0x5d/0x720 [usbnet]
The cdc_ncm_align_tail call first aligns on a ctx->tx_modulus
boundary (adding at most ctx->tx_modulus-1 bytes), then adds
ctx->tx_remainder bytes. Alternatively, the next alignment call can
occur in cdc_ncm_ndp16 or cdc_ncm_ndp32, in which case at most
ctx->tx_ndp_modulus-1 bytes are added.
A similar problem has occurred before, and the code is nontrivial to
reason about, so add a guard before the crashing call. By that time it
is too late to prevent any memory corruption (we'll have written past
the end of the buffer already) but we can at least try to get a warning
written into an on-disk log by avoiding the hard crash caused by padding
past the buffer with a huge number of zeros.
Signed-off-by: Jouni K. Seppänen <jks@iki.fi>
Fixes: 4a0e3e989d66 ("cdc_ncm: Add support for moving NDP to end of NCM frame")
Link: https://bugzilla.kernel.org/show_bug.cgi?id=209407
Reported-by: kernel test robot <lkp@intel.com>
Reviewed-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
For DEVICE_VERSION_V2, the hardware only supports src-ip,
dst-ip and verification-tag for rss tuple set of sctp6
packet. For DEVICE_VERSION_V3, the hardware supports
src-port and dst-port as well.
Currently, when user queries the sctp6 rss tuples info,
some unsupported information will be showed on V2. So add
a check for hardware version when initializing and queries
sctp6 rss tuple to fix this issue.
Fixes: 46a3df9f9718 ("net: hns3: Add HNS3 Acceleration Engine & Compatibility Layer Support")
Signed-off-by: Jian Shen <shenjian15@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
HCLGE_MBX_MAX_ARQ_MSG_NUM is used to apply memory for the number
of queues used by ARQ(Asynchronous Receive Queue), so the head
and tail pointers should also use this macro.
Fixes: 07a0556a3a73 ("net: hns3: Changes to support ARQ(Asynchronous Receive Queue)")
Signed-off-by: Yufeng Mo <moyufeng@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When phy driver does not implement the set_loopback interface,
phy loopback test will return -EOPNOTSUPP, and the loopback test
will fail. So when phy driver does not implement the set_loopback
interface, don't do phy loopback test.
Fixes: c9765a89d142 ("net: hns3: add phy selftest function")
Signed-off-by: Yonglong Liu <liuyonglong@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Previously, sun8i_dwmac_set_syscon was called from a chain of functions
in several different files:
sun8i_dwmac_probe
stmmac_dvr_probe
stmmac_hw_init
stmmac_hwif_init
sun8i_dwmac_setup
sun8i_dwmac_set_syscon
which made the lifetime of the syscon values hard to reason about. Part
of the problem is that there is no similar platform driver callback from
stmmac_dvr_remove. As a result, the driver unset the syscon value in
sun8i_dwmac_exit, but this leaves it uninitialized after a suspend/
resume cycle. It was also unset a second time (outside sun8i_dwmac_exit)
in the probe error path.
Move the init to the earliest available place in sun8i_dwmac_probe
(after stmmac_probe_config_dt, which initializes plat_dat), and the
deinit to the corresponding position in the cleanup order.
Since priv is not filled in until stmmac_dvr_probe, this requires
changing the sun8i_dwmac_set_syscon parameters to priv's two relevant
members.
Fixes: 9f93ac8d4085 ("net-next: stmmac: Add dwmac-sun8i")
Fixes: 634db83b8265 ("net: stmmac: dwmac-sun8i: Handle integrated/external MDIOs")
Signed-off-by: Samuel Holland <samuel@sholland.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
sun8i_dwmac_exit calls sun8i_dwmac_unpower_internal_phy, but
sun8i_dwmac_init did not call sun8i_dwmac_power_internal_phy. This
caused PHY power to remain off after a suspend/resume cycle. Fix this by
recording if PHY power should be restored, and if so, restoring it.
Fixes: 634db83b8265 ("net: stmmac: dwmac-sun8i: Handle integrated/external MDIOs")
Signed-off-by: Samuel Holland <samuel@sholland.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
While stmmac_pltfr_remove calls sun8i_dwmac_exit, the sun8i_dwmac_init
and sun8i_dwmac_exit functions are also called by the stmmac_platform
suspend/resume callbacks. They may be called many times during the
device's lifetime and should not release resources used by the driver.
Furthermore, there was no error handling in case registering the MDIO
mux failed during probe, and the EPHY clock was never released at all.
Fix all of these issues by moving the deinitialization code to a driver
removal callback. Also ensure the EPHY is powered down before removal.
Fixes: 634db83b8265 ("net: stmmac: dwmac-sun8i: Handle integrated/external MDIOs")
Signed-off-by: Samuel Holland <samuel@sholland.org>
Reviewed-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
stmmac_pltfr_remove does three things in one function, making it
inapproprate for unwinding the steps in the probe function. Currently,
a failure before the call to stmmac_dvr_probe would leak OF node
references due to missing a call to stmmac_remove_config_dt. And an
error in stmmac_dvr_probe would cause the driver to attempt to remove a
netdevice that was never added. Fix these by reordering the init and
splitting out the error handling steps.
Fixes: 9f93ac8d4085 ("net-next: stmmac: Add dwmac-sun8i")
Fixes: 40a1dcee2d18 ("net: ethernet: dwmac-sun8i: Use the correct function in exit path")
Signed-off-by: Samuel Holland <samuel@sholland.org>
Reviewed-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
A call to dma_alloc_coherent() is wrapped by sonic_alloc_descriptors().
This is correctly freed in the remove function, but not in the error
handling path of the probe function. Fix this by adding the missing
dma_free_coherent() call.
While at it, rename a label in order to be slightly more informative.
Cc: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Cc: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
Cc: Chris Zankel <chris@zankel.net>
References: commit 10e3cc180e64 ("net/sonic: Fix a resource leak in an error handling path in 'jazz_sonic_probe()'")
Fixes: 74f2a5f0ef64 ("xtensa: Add support for the Sonic Ethernet device for the XT2000 board.")
Fixes: efcce839360f ("[PATCH] macsonic/jazzsonic network drivers update")
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Signed-off-by: Finn Thain <fthain@telegraphics.com.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Without this, the driver runs into a link failure
arm-linux-gnueabi-ld: drivers/net/wan/slic_ds26522.o: in function `slic_ds26522_probe':
slic_ds26522.c:(.text+0x100c): undefined reference to `byte_rev_table'
arm-linux-gnueabi-ld: slic_ds26522.c:(.text+0x1cdc): undefined reference to `byte_rev_table'
arm-linux-gnueabi-ld: drivers/net/wan/slic_ds26522.o: in function `slic_write':
slic_ds26522.c:(.text+0x1e4c): undefined reference to `byte_rev_table'
Fixes: c37d4a0085c5 ("Maxim/driver: Add driver for maxim ds26522")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Without this, we run into a link error
arm-linux-gnueabi-ld: drivers/isdn/mISDN/dsp_audio.o: in function `dsp_audio_generate_law_tables':
(.text+0x30c): undefined reference to `byte_rev_table'
arm-linux-gnueabi-ld: drivers/isdn/mISDN/dsp_audio.o:(.text+0x5e4): more undefined references to `byte_rev_table' follow
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Without crc32, the driver fails to link:
arm-linux-gnueabi-ld: drivers/net/wireless/ath/wil6210/fw.o: in function `wil_fw_verify':
fw.c:(.text+0x74c): undefined reference to `crc32_le'
arm-linux-gnueabi-ld: drivers/net/wireless/ath/wil6210/fw.o:fw.c:(.text+0x758): more undefined references to `crc32_le' follow
Fixes: 151a9706503f ("wil6210: firmware download")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Without crc32, this driver fails to link:
arm-linux-gnueabi-ld: drivers/net/can/kvaser_pciefd.o: in function `kvaser_pciefd_probe':
kvaser_pciefd.c:(.text+0x2b0): undefined reference to `crc32_be'
Fixes: 26ad340e582d ("can: kvaser_pciefd: Add driver for Kvaser PCIEcan devices")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Without crc32, this driver fails to link:
arm-linux-gnueabi-ld: drivers/net/phy/dp83640.o: in function `match':
dp83640.c:(.text+0x476c): undefined reference to `crc32_le'
Fixes: 539e44d26855 ("dp83640: Include hash in timestamp/packet matching")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Acked-by: Richard Cochran <richardcochran@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Without this, the driver fails to link:
lpc_eth.c:(.text+0x1934): undefined reference to `crc32_le'
arm-linux-gnueabi-ld: drivers/net/ethernet/qlogic/qed/qed_debug.o: in function `qed_grc_dump':
qed_debug.c:(.text+0x4068): undefined reference to `crc32_le'
arm-linux-gnueabi-ld: drivers/net/ethernet/qlogic/qed/qed_debug.o: in function `qed_idle_chk_dump':
qed_debug.c:(.text+0x51fc): undefined reference to `crc32_le'
arm-linux-gnueabi-ld: drivers/net/ethernet/qlogic/qed/qed_debug.o: in function `qed_mcp_trace_dump':
qed_debug.c:(.text+0x6000): undefined reference to `crc32_le'
arm-linux-gnueabi-ld: drivers/net/ethernet/qlogic/qed/qed_debug.o: in function `qed_dbg_reg_fifo_dump':
qed_debug.c:(.text+0x66cc): undefined reference to `crc32_le'
arm-linux-gnueabi-ld: drivers/net/ethernet/qlogic/qed/qed_debug.o:qed_debug.c:(.text+0x6aa4): more undefined references to `crc32_le' follow
Fixes: 7a4b21b7d1f0 ("qed: Add nvram selftest")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Pull vhost bugfix from Michael Tsirkin:
"This fixes configs with vhost vsock behind a viommu"
* tag 'for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mst/vhost:
vhost/vsock: add IOTLB API support
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net
Pull networking fixes from Jakub Kicinski:
"Networking fixes, including fixes from netfilter, wireless and bpf
trees.
Current release - regressions:
- mt76: fix NULL pointer dereference in mt76u_status_worker and
mt76s_process_tx_queue
- net: ipa: fix interconnect enable bug
Current release - always broken:
- netfilter: fixes possible oops in mtype_resize in ipset
- ath11k: fix number of coding issues found by static analysis tools
and spurious error messages
Previous releases - regressions:
- e1000e: re-enable s0ix power saving flows for systems with the
Intel i219-LM Ethernet controllers to fix power use regression
- virtio_net: fix recursive call to cpus_read_lock() to avoid a
deadlock
- ipv4: ignore ECN bits for fib lookups in fib_compute_spec_dst()
- sysfs: take the rtnl lock around XPS configuration
- xsk: fix memory leak for failed bind and rollback reservation at
NETDEV_TX_BUSY
- r8169: work around power-saving bug on some chip versions
Previous releases - always broken:
- dcb: validate netlink message in DCB handler
- tun: fix return value when the number of iovs exceeds MAX_SKB_FRAGS
to prevent unnecessary retries
- vhost_net: fix ubuf refcount when sendmsg fails
- bpf: save correct stopping point in file seq iteration
- ncsi: use real net-device for response handler
- neighbor: fix div by zero caused by a data race (TOCTOU)
- bareudp: fix use of incorrect min_headroom size and a false
positive lockdep splat from the TX lock
- mvpp2:
- clear force link UP during port init procedure in case
bootloader had set it
- add TCAM entry to drop flow control pause frames
- fix PPPoE with ipv6 packet parsing
- fix GoP Networking Complex Control config of port 3
- fix pkt coalescing IRQ-threshold configuration
- xsk: fix race in SKB mode transmit with shared cq
- ionic: account for vlan tag len in rx buffer len
- stmmac: ignore the second clock input, current clock framework does
not handle exclusive clock use well, other drivers may reconfigure
the second clock
Misc:
- ppp: change PPPIOCUNBRIDGECHAN ioctl request number to follow
existing scheme"
* tag 'net-5.11-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net: (99 commits)
net: dsa: lantiq_gswip: Fix GSWIP_MII_CFG(p) register access
net: dsa: lantiq_gswip: Enable GSWIP_MII_CFG_EN also for internal PHYs
net: lapb: Decrease the refcount of "struct lapb_cb" in lapb_device_event
r8169: work around power-saving bug on some chip versions
net: usb: qmi_wwan: add Quectel EM160R-GL
selftests: mlxsw: Set headroom size of correct port
net: macb: Correct usage of MACB_CAPS_CLK_HW_CHG flag
ibmvnic: fix: NULL pointer dereference.
docs: networking: packet_mmap: fix old config reference
docs: networking: packet_mmap: fix formatting for C macros
vhost_net: fix ubuf refcount incorrectly when sendmsg fails
bareudp: Fix use of incorrect min_headroom size
bareudp: set NETIF_F_LLTX flag
net: hdlc_ppp: Fix issues when mod_timer is called while timer is running
atlantic: remove architecture depends
erspan: fix version 1 check in gre_parse_header()
net: hns: fix return value check in __lb_other_process()
net: sched: prevent invalid Scell_log shift count
net: neighbor: fix a crash caused by mod zero
ipv4: Ignore ECN bits for fib lookups in fib_compute_spec_dst()
...
|
|
The AMD IOMMU initialisation registers the IRQ remapping domain for
each IOMMU before doing the final sanity check that every I/OAPIC is
covered.
This means that the AMD irq_remapping_select() function gets invoked
even when IRQ remapping has been disabled, eventually leading to a NULL
pointer dereference in alloc_irq_table().
Unfortunately, the IVRS isn't fully parsed early enough that the sanity
check can be done in time to registering the IRQ domain altogether.
Doing that would be nice, but is a larger and more error-prone task. The
simple fix is just for irq_remapping_select() to refuse to report a
match when IRQ remapping has disabled.
Link: https://lore.kernel.org/lkml/ed4be9b4-24ac-7128-c522-7ef359e8185d@gmx.at
Fixes: a1a785b57242 ("iommu/amd: Implement select() method on remapping irqdomain")
Reported-by: Johnathan Smithinovic <johnathan.smithinovic@gmx.at>
Signed-off-by: David Woodhouse <dwmw@amazon.co.uk>
Link: https://lore.kernel.org/r/04bbe8bca87f81a3cfa93ec4299e53f47e00e5b3.camel@infradead.org
Signed-off-by: Will Deacon <will@kernel.org>
|
|
When I made the INTCAPXT support stop gratuitously pretending to be MSI,
I missed the fact that iommu_setup_msi() also sets the ->int_enabled
flag. I missed this in the iommu_setup_intcapxt() code path, which means
that a resume from suspend will try to allocate the IRQ domains again,
accidentally re-enabling interrupts as it does, resulting in much sadness.
Lift out the bit which sets iommu->int_enabled into the iommu_init_irq()
function which is also where it gets checked.
Link: https://lore.kernel.org/r/20210104132250.GE32151@zn.tnic/
Fixes: d1adcfbb520c ("iommu/amd: Fix IOMMU interrupt generation in X2APIC mode")
Reported-by: Borislav Petkov <bp@alien8.de>
Signed-off-by: David Woodhouse <dwmw@amazon.co.uk>
Tested-by: Borislav Petkov <bp@suse.de>
Link: https://lore.kernel.org/r/50cd5f55be8ead0937ac315cd2f5b89364f6a9a5.camel@infradead.org
Signed-off-by: Will Deacon <will@kernel.org>
|
|
When irq_domain_get_irq_data() or irqd_cfg() fails
at i == 0, data allocated by kzalloc() has not been
freed before returning, which leads to memleak.
Fixes: b106ee63abcc ("irq_remapping/vt-d: Enhance Intel IR driver to support hierarchical irqdomains")
Signed-off-by: Dinghao Liu <dinghao.liu@zju.edu.cn>
Acked-by: Lu Baolu <baolu.lu@linux.intel.com>
Link: https://lore.kernel.org/r/20210105051837.32118-1-dinghao.liu@zju.edu.cn
Signed-off-by: Will Deacon <will@kernel.org>
|
|
Replace misspelled 'doamin' with 'domain' in several comments.
Signed-off-by: Stefano Garzarella <sgarzare@redhat.com>
Link: https://lore.kernel.org/r/20201222164232.88795-1-sgarzare@redhat.com
Signed-off-by: Will Deacon <will@kernel.org>
|
|
This code will leak "map->debugfs_name" because the if statement is
reversed so it only frees NULL pointers instead of non-NULL. In
fact the if statement is not required and should just be removed
because kfree() accepts NULL pointers.
Fixes: cffa4b2122f5 ("regmap: debugfs: Fix a memory leak when calling regmap_attach_dev")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Link: https://lore.kernel.org/r/X/RQpfAwRdLg0GqQ@mwanda
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Here's another variant PNY Pro Elite USB 3.1 Gen 2 portable SSD that
hangs and doesn't respond to ATA_1x pass-through commands. If it doesn't
support these commands, it should respond properly to the host. Add it
to the unusual uas list to be able to move forward with other
operations.
Cc: stable@vger.kernel.org
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Oliver Neukum <oneukum@suse.com>
Signed-off-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com>
Link: https://lore.kernel.org/r/2edc7af892d0913bf06f5b35e49ec463f03d5ed8.1609819418.git.Thinh.Nguyen@synopsys.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
With the apdma remove hand-shake signal, it requirs special
operation timing to reset i2c manually, otherwise the interrupt
will not be triggered, i2c transmission will be timeout.
Fixes: 8426fe70cfa4("i2c: mediatek: Add apdma sync in i2c driver")
Signed-off-by: Qii Wang <qii.wang@mediatek.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
|
|
Since multiple connectors may run intel_dp_aux_xfer conncurrently, a
single global pm_qos does not suffice. (One connector may disable the
dma-latency boost prematurely while the second is still depending on
it.) Instead of a single global pm_qos, track the pm_qos request for
each intel_dp.
v2: Move the pm_qos setup/teardown to intel_dp_aux_init/fini
Fixes: 9ee32fea5fe8 ("drm/i915: irq-drive the dp aux communication")
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: Imre Deak <imre.deak@intel.com>
Reviewed-by: Imre Deak <imre.deak@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20201230202309.23982-1-chris@chris-wilson.co.uk
(cherry picked from commit b3304591f14b437b6bccd8dbff06006c11837031)
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
|
|
When splitting the Coffeelake define to also identify Cometlakes, I
missed the double fw_def for Coffeelake. That is only newer Cometlakes
use the cml specific guc firmware, older Cometlakes should use kbl
firmware.
Closes: https://gitlab.freedesktop.org/drm/intel/-/issues/2859
Fixes: 5f4ae2704d59 ("drm/i915: Identify Cometlake platform")
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: <stable@vger.kernel.org> # v5.9+
Reviewed-by: Mika Kuoppala <mika.kuoppala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20201229120828.29931-1-chris@chris-wilson.co.uk
(cherry picked from commit 70960ab27542d8dc322f909f516391f331fbd3f1)
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
|
|
The reloc batch is short lived but can exist in the user visible ppGTT,
and since it's backed by an internal object, which lacks page clearing,
we should take care to clear it upfront.
Signed-off-by: Matthew Auld <matthew.auld@intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Link: https://patchwork.freedesktop.org/patch/msgid/20201224151358.401345-2-matthew.auld@intel.com
Cc: stable@vger.kernel.org
(cherry picked from commit 26ebc511e799f621357982ccc37a7987a56a00f4)
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
|
