summaryrefslogtreecommitdiff
path: root/drivers
AgeCommit message (Collapse)Author
2024-09-18usbnet: ipheth: fix carrier detection in modes 1 and 4Foster Snowhill
[ Upstream commit 67927a1b255d883881be9467508e0af9a5e0be9d ] Apart from the standard "configurations", "interfaces" and "alternate interface settings" in USB, iOS devices also have a notion of "modes". In different modes, the device exposes a different set of available configurations. Depending on the iOS version, and depending on the current mode, the length and contents of the carrier state control message differs: * 1 byte (seen on iOS 4.2.1, 8.4): * 03: carrier off (mode 0) * 04: carrier on (mode 0) * 3 bytes (seen on iOS 10.3.4, 15.7.6): * 03 03 03: carrier off (mode 0) * 04 04 03: carrier on (mode 0) * 4 bytes (seen on iOS 16.5, 17.6): * 03 03 03 00: carrier off (mode 0) * 04 03 03 00: carrier off (mode 1) * 06 03 03 00: carrier off (mode 4) * 04 04 03 04: carrier on (mode 0 and 1) * 06 04 03 04: carrier on (mode 4) Before this change, the driver always used the first byte of the response to determine carrier state. From this larger sample, the first byte seems to indicate the number of available USB configurations in the current mode (with the exception of the default mode 0), and in some cases (namely mode 1 and 4) does not correlate with the carrier state. Previous logic erroneously counted `04 03 03 00` as "carrier on" and `06 04 03 04` as "carrier off" on iOS versions that support mode 1 and mode 4 respectively. Only modes 0, 1 and 4 expose the USB Ethernet interfaces necessary for the ipheth driver. Check the second byte of the control message where possible, and fall back to checking the first byte on older iOS versions. Signed-off-by: Foster Snowhill <forst@pen.gy> Tested-by: Georgi Valkov <gvalkov@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
2024-09-18usbnet: ipheth: do not stop RX on failing RX callbackFoster Snowhill
[ Upstream commit 74efed51e0a4d62f998f806c307778b47fc73395 ] RX callbacks can fail for multiple reasons: * Payload too short * Payload formatted incorrecly (e.g. bad NCM framing) * Lack of memory None of these should cause the driver to seize up. Make such failures non-critical and continue processing further incoming URBs. Signed-off-by: Foster Snowhill <forst@pen.gy> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
2024-09-18usbnet: ipheth: drop RX URBs with no payloadFoster Snowhill
[ Upstream commit 94d7eeb6c0ef0310992944f0d0296929816a2cb0 ] On iPhone 15 Pro Max one can observe periodic URBs with no payload on the "bulk in" (RX) endpoint. These don't seem to do anything meaningful. Reproduced on iOS 17.5.1 and 17.6. This behaviour isn't observed on iPhone 11 on the same iOS version. The nature of these zero-length URBs is so far unknown. Drop RX URBs with no payload. Signed-off-by: Foster Snowhill <forst@pen.gy> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
2024-09-18usbnet: ipheth: remove extraneous rx URB length checkFoster Snowhill
[ Upstream commit 655b46d7a39ac6f049698b27c1568c0f7ff85d1e ] Rx URB length was already checked in ipheth_rcvbulk_callback_legacy() and ipheth_rcvbulk_callback_ncm(), depending on the current mode. The check in ipheth_rcvbulk_callback() was thus mostly a duplicate. The only place in ipheth_rcvbulk_callback() where we care about the URB length is for the initial control frame. These frames are always 4 bytes long. This has been checked as far back as iOS 4.2.1 on iPhone 3G. Remove the extraneous URB length check. For control frames, check for the specific 4-byte length instead. Signed-off-by: Foster Snowhill <forst@pen.gy> Tested-by: Georgi Valkov <gvalkov@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
2024-09-18nvmem: u-boot-env: error if NVMEM device is too smallJohn Thomson
[ Upstream commit 8679e8b4a1ebdb40c4429e49368d29353e07b601 ] Verify data size before trying to parse it to avoid reading out of buffer. This could happen in case of problems at MTD level or invalid DT bindings. Signed-off-by: John Thomson <git@johnthomson.fastmail.com.au> Cc: stable <stable@kernel.org> Fixes: d5542923f200 ("nvmem: add driver handling U-Boot environment variables") [rmilecki: simplify commit description & rebase] Signed-off-by: Rafał Miłecki <rafal@milecki.pl> Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org> Link: https://lore.kernel.org/r/20240902142510.71096-2-srinivas.kandagatla@linaro.org Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
2024-09-18nvmem: u-boot-env: improve coding styleRafał Miłecki
[ Upstream commit 6bafe07c930676d6430be471310958070816a595 ] 1. Prefer kzalloc() over kcalloc() See memory-allocation.rst which says: "to be on the safe side it's best to use routines that set memory to zero, like kzalloc()" 2. Drop dev_err() for u_boot_env_add_cells() fail It can fail only on -ENOMEM. We don't want to print error then. 3. Add extra "crc32_addr" variable It makes code reading header's crc32 easier to understand / review. Signed-off-by: Rafał Miłecki <rafal@milecki.pl> Reviewed-by: Miquel Raynal <miquel.raynal@bootlin.com> Link: https://lore.kernel.org/r/20231221173421.13737-5-zajec5@gmail.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Stable-dep-of: 8679e8b4a1eb ("nvmem: u-boot-env: error if NVMEM device is too small") Signed-off-by: Sasha Levin <sashal@kernel.org>
2024-09-18nvmem: u-boot-env: use nvmem device helpersRafał Miłecki
[ Upstream commit a832556d23c5a11115f300011a5874d6107a0d62 ] Use nvmem_dev_size() and nvmem_device_read() to make this driver less mtd dependent. Signed-off-by: Rafał Miłecki <rafal@milecki.pl> Reviewed-by: Miquel Raynal <miquel.raynal@bootlin.com> Link: https://lore.kernel.org/r/20231221173421.13737-4-zajec5@gmail.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Stable-dep-of: 8679e8b4a1eb ("nvmem: u-boot-env: error if NVMEM device is too small") Signed-off-by: Sasha Levin <sashal@kernel.org>
2024-09-18nvmem: u-boot-env: use nvmem_add_one_cell() nvmem subsystem helperRafał Miłecki
[ Upstream commit 7c8979b42b1a9c5604f431ba804928e55919263c ] Simplify adding NVMEM cells. Signed-off-by: Rafał Miłecki <rafal@milecki.pl> Reviewed-by: Miquel Raynal <miquel.raynal@bootlin.com> Link: https://lore.kernel.org/r/20231221173421.13737-3-zajec5@gmail.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Stable-dep-of: 8679e8b4a1eb ("nvmem: u-boot-env: error if NVMEM device is too small") Signed-off-by: Sasha Levin <sashal@kernel.org>
2024-09-18nvmem: core: add nvmem_dev_size() helperRafał Miłecki
[ Upstream commit 33cf42e68efc8ff529a7eee08a4f0ba8c8d0a207 ] This is required by layouts that need to read whole NVMEM content. It's especially useful for NVMEM devices without hardcoded layout (like U-Boot environment data block). Signed-off-by: Rafał Miłecki <rafal@milecki.pl> Reviewed-by: Miquel Raynal <miquel.raynal@bootlin.com> Link: https://lore.kernel.org/r/20231221173421.13737-2-zajec5@gmail.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Stable-dep-of: 8679e8b4a1eb ("nvmem: u-boot-env: error if NVMEM device is too small") Signed-off-by: Sasha Levin <sashal@kernel.org>
2024-09-18iio: adc: ad7124: fix DT configuration parsingDumitru Ceclan
[ Upstream commit 61cbfb5368dd50ed0d65ce21d305aa923581db2b ] The cfg pointer is set before reading the channel number that the configuration should point to. This causes configurations to be shifted by one channel. For example setting bipolar to the first channel defined in the DT will cause bipolar mode to be active on the second defined channel. Fix by moving the cfg pointer setting after reading the channel number. Fixes: 7b8d045e497a ("iio: adc: ad7124: allow more than 8 channels") Signed-off-by: Dumitru Ceclan <dumitru.ceclan@analog.com> Reviewed-by: Nuno Sa <nuno.sa@analog.com> Link: https://patch.msgid.link/20240806085133.114547-1-dumitru.ceclan@analog.com Cc: <Stable@vger.kernel.org> Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
2024-09-18iio: adc: ad7124: Switch from of specific to fwnode based property handlingJonathan Cameron
[ Upstream commit a6eaf02b82744b424b9b2c74847282deb2c6f77b ] Using the generic firmware data access functions from property.h provides a number of advantages: 1) Works with different firmware types. 2) Doesn't provide a 'bad' example for new IIO drivers. 3) Lets us use the new _scoped() loops with automatic reference count cleanup for fwnode_handle Cc: Lars-Peter Clausen <lars@metafoo.de> Cc: Michael Hennerich <Michael.Hennerich@analog.com> Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com> Link: https://lore.kernel.org/r/20240218172731.1023367-4-jic23@kernel.org Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com> Stable-dep-of: 61cbfb5368dd ("iio: adc: ad7124: fix DT configuration parsing") Signed-off-by: Sasha Levin <sashal@kernel.org>
2024-09-12spi: spi-fsl-lpspi: Fix off-by-one in prescale maxStefan Wahren
commit ff949d981c775332be94be70397ee1df20bc68e5 upstream. The commit 783bf5d09f86 ("spi: spi-fsl-lpspi: limit PRESCALE bit in TCR register") doesn't implement the prescaler maximum as intended. The maximum allowed value for i.MX93 should be 1 and for i.MX7ULP it should be 7. So this needs also a adjustment of the comparison in the scldiv calculation. Fixes: 783bf5d09f86 ("spi: spi-fsl-lpspi: limit PRESCALE bit in TCR register") Signed-off-by: Stefan Wahren <wahrenst@gmx.net> Link: https://patch.msgid.link/20240905111537.90389-1-wahrenst@gmx.net Signed-off-by: Mark Brown <broonie@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2024-09-12ublk_drv: fix NULL pointer dereference in ublk_ctrl_start_recovery()Li Nan
[ Upstream commit e58f5142f88320a5b1449f96a146f2f24615c5c7 ] When two UBLK_CMD_START_USER_RECOVERY commands are submitted, the first one sets 'ubq->ubq_daemon' to NULL, and the second one triggers WARN in ublk_queue_reinit() and subsequently a NULL pointer dereference issue. Fix it by adding the check in ublk_ctrl_start_recovery() and return immediately in case of zero 'ub->nr_queues_ready'. BUG: kernel NULL pointer dereference, address: 0000000000000028 RIP: 0010:ublk_ctrl_start_recovery.constprop.0+0x82/0x180 Call Trace: <TASK> ? __die+0x20/0x70 ? page_fault_oops+0x75/0x170 ? exc_page_fault+0x64/0x140 ? asm_exc_page_fault+0x22/0x30 ? ublk_ctrl_start_recovery.constprop.0+0x82/0x180 ublk_ctrl_uring_cmd+0x4f7/0x6c0 ? pick_next_task_idle+0x26/0x40 io_uring_cmd+0x9a/0x1b0 io_issue_sqe+0x193/0x3f0 io_wq_submit_work+0x9b/0x390 io_worker_handle_work+0x165/0x360 io_wq_worker+0xcb/0x2f0 ? finish_task_switch.isra.0+0x203/0x290 ? finish_task_switch.isra.0+0x203/0x290 ? __pfx_io_wq_worker+0x10/0x10 ret_from_fork+0x2d/0x50 ? __pfx_io_wq_worker+0x10/0x10 ret_from_fork_asm+0x1a/0x30 </TASK> Fixes: c732a852b419 ("ublk_drv: add START_USER_RECOVERY and END_USER_RECOVERY support") Reported-and-tested-by: Changhui Zhong <czhong@redhat.com> Closes: https://lore.kernel.org/all/CAGVVp+UvLiS+bhNXV-h2icwX1dyybbYHeQUuH7RYqUvMQf6N3w@mail.gmail.com Reviewed-by: Ming Lei <ming.lei@redhat.com> Signed-off-by: Li Nan <linan122@huawei.com> Link: https://lore.kernel.org/r/20240904031348.4139545-1-ming.lei@redhat.com Signed-off-by: Jens Axboe <axboe@kernel.dk> Signed-off-by: Sasha Levin <sashal@kernel.org>
2024-09-12gpio: modepin: Enable module autoloadingLiao Chen
[ Upstream commit a5135526426df5319d5f4bcd15ae57c45a97714b ] Add MODULE_DEVICE_TABLE(), so modules could be properly autoloaded based on the alias from of_device_id table. Fixes: 7687a5b0ee93 ("gpio: modepin: Add driver support for modepin GPIO controller") Signed-off-by: Liao Chen <liaochen4@huawei.com> Reviewed-by: Michal Simek <michal.simek@amd.com> Link: https://lore.kernel.org/r/20240902115848.904227-1-liaochen4@huawei.com Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
2024-09-12gpio: rockchip: fix OF node leak in probe()Krzysztof Kozlowski
[ Upstream commit adad2e460e505a556f5ea6f0dc16fe95e62d5d76 ] Driver code is leaking OF node reference from of_get_parent() in probe(). Fixes: 936ee2675eee ("gpio/rockchip: add driver for rockchip gpio") Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org> Reviewed-by: Heiko Stuebner <heiko@sntech.de> Reviewed-by: Shawn Lin <shawn.lin@rock-chips.com> Link: https://lore.kernel.org/r/20240826150832.65657-1-krzysztof.kozlowski@linaro.org Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
2024-09-12drm/i915/fence: Mark debug_fence_free() with __maybe_unusedAndy Shevchenko
[ Upstream commit f99999536128b14b5d765a9982763b5134efdd79 ] When debug_fence_free() is unused (CONFIG_DRM_I915_SW_FENCE_DEBUG_OBJECTS=n), it prevents kernel builds with clang, `make W=1` and CONFIG_WERROR=y: .../i915_sw_fence.c:118:20: error: unused function 'debug_fence_free' [-Werror,-Wunused-function] 118 | static inline void debug_fence_free(struct i915_sw_fence *fence) | ^~~~~~~~~~~~~~~~ Fix this by marking debug_fence_free() with __maybe_unused. See also commit 6863f5643dd7 ("kbuild: allow Clang to find unused static inline functions for W=1 build"). Fixes: fc1584059d6c ("drm/i915: Integrate i915_sw_fence with debugobjects") Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com> Reviewed-by: Jani Nikula <jani.nikula@intel.com> Link: https://patchwork.freedesktop.org/patch/msgid/20240829155950.1141978-3-andriy.shevchenko@linux.intel.com Signed-off-by: Jani Nikula <jani.nikula@intel.com> (cherry picked from commit 8be4dce5ea6f2368cc25edc71989c4690fa66964) Signed-off-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
2024-09-12drm/i915/fence: Mark debug_fence_init_onstack() with __maybe_unusedAndy Shevchenko
[ Upstream commit fcd9e8afd546f6ced378d078345a89bf346d065e ] When debug_fence_init_onstack() is unused (CONFIG_DRM_I915_SELFTEST=n), it prevents kernel builds with clang, `make W=1` and CONFIG_WERROR=y: .../i915_sw_fence.c:97:20: error: unused function 'debug_fence_init_onstack' [-Werror,-Wunused-function] 97 | static inline void debug_fence_init_onstack(struct i915_sw_fence *fence) | ^~~~~~~~~~~~~~~~~~~~~~~~ Fix this by marking debug_fence_init_onstack() with __maybe_unused. See also commit 6863f5643dd7 ("kbuild: allow Clang to find unused static inline functions for W=1 build"). Fixes: 214707fc2ce0 ("drm/i915/selftests: Wrap a timer into a i915_sw_fence") Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com> Reviewed-by: Jani Nikula <jani.nikula@intel.com> Link: https://patchwork.freedesktop.org/patch/msgid/20240829155950.1141978-2-andriy.shevchenko@linux.intel.com Signed-off-by: Jani Nikula <jani.nikula@intel.com> (cherry picked from commit 5bf472058ffb43baf6a4cdfe1d7f58c4c194c688) Signed-off-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
2024-09-12clk: qcom: gcc-sm8550: Don't park the USB RCG at registration timeStephen Boyd
[ Upstream commit 7b6dfa1bbe7f727315d2e05a2fc8e4cfeb779156 ] Amit Pundir reports that audio and USB-C host mode stops working if the gcc_usb30_prim_master_clk_src clk is registered and clk_rcg2_shared_init() parks it on XO. Skip parking this clk at registration time to fix those issues. Partially revert commit 01a0a6cc8cfd ("clk: qcom: Park shared RCGs upon registration") by skipping the parking bit for this clk, but keep the part where we cache the config register. That's still necessary to figure out the true parent of the clk at registration time. Fixes: 01a0a6cc8cfd ("clk: qcom: Park shared RCGs upon registration") Fixes: 929c75d57566 ("clk: qcom: gcc-sm8550: Mark RCGs shared where applicable") Cc: Konrad Dybcio <konradybcio@kernel.org> Cc: Bjorn Andersson <andersson@kernel.org> Cc: Taniya Das <quic_tdas@quicinc.com> Reported-by: Amit Pundir <amit.pundir@linaro.org> Closes: https://lore.kernel.org/CAMi1Hd1KQBE4kKUdAn8E5FV+BiKzuv+8FoyWQrrTHPDoYTuhgA@mail.gmail.com Signed-off-by: Stephen Boyd <swboyd@chromium.org> Link: https://lore.kernel.org/r/20240819233628.2074654-3-swboyd@chromium.org Tested-by: Amit Pundir <amit.pundir@linaro.org> Signed-off-by: Stephen Boyd <sboyd@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
2024-09-12clk: qcom: gcc-sm8550: Don't use parking clk_ops for QUPsStephen Boyd
[ Upstream commit d10eeb75168b84ed9559c58efe2756c2e0bc052a ] The QUPs aren't shared in a way that requires parking the RCG at an always on parent in case some other entity turns on the clk. The hardware is capable of setting a new frequency itself with the DFS mode, so parking is unnecessary. Furthermore, there aren't any GDSCs for these devices, so there isn't a possibility of the GDSC turning on the clks for housekeeping purposes. This wasn't a problem to mark these clks shared until we started parking shared RCGs at clk registration time in commit 01a0a6cc8cfd ("clk: qcom: Park shared RCGs upon registration"). Parking at init is actually harmful to the UART when earlycon is used. If the device is pumping out data while the frequency changes you'll see garbage on the serial console until the driver can probe and actually set a proper frequency. Revert the QUP part of commit 929c75d57566 ("clk: qcom: gcc-sm8550: Mark RCGs shared where applicable") so that the QUPs don't get parked during clk registration and break UART operations. Fixes: 01a0a6cc8cfd ("clk: qcom: Park shared RCGs upon registration") Fixes: 929c75d57566 ("clk: qcom: gcc-sm8550: Mark RCGs shared where applicable") Cc: Konrad Dybcio <konradybcio@kernel.org> Cc: Bjorn Andersson <andersson@kernel.org> Cc: Taniya Das <quic_tdas@quicinc.com> Reported-by: Amit Pundir <amit.pundir@linaro.org> Closes: https://lore.kernel.org/CAMi1Hd1KQBE4kKUdAn8E5FV+BiKzuv+8FoyWQrrTHPDoYTuhgA@mail.gmail.com Signed-off-by: Stephen Boyd <swboyd@chromium.org> Link: https://lore.kernel.org/r/20240819233628.2074654-2-swboyd@chromium.org Tested-by: Amit Pundir <amit.pundir@linaro.org> Tested-by: Neil Armstrong <neil.armstrong@linaro.org> # on SM8550-QRD Signed-off-by: Stephen Boyd <sboyd@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
2024-09-12nvme-pci: allocate tagset on reset if necessaryKeith Busch
[ Upstream commit 6f01bdbfef3b62955cf6503a8425d527b3a5cf94 ] If a drive is unable to create IO queues on the initial probe, a subsequent reset will need to allocate the tagset if IO queue creation is successful. Without this, blk_mq_update_nr_hw_queues will crash on a bad pointer due to the invalid tagset. Fixes: eac3ef262941f62 ("nvme-pci: split the initial probe from the rest path") Reviewed-by: Sagi Grimberg <sagi@grimberg.me> Reviewed-by: Christoph Hellwig <hch@lst.de> Signed-off-by: Keith Busch <kbusch@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
2024-09-12nvmet-tcp: fix kernel crash if commands allocation failsMaurizio Lombardi
[ Upstream commit 5572a55a6f830ee3f3a994b6b962a5c327d28cb3 ] If the commands allocation fails in nvmet_tcp_alloc_cmds() the kernel crashes in nvmet_tcp_release_queue_work() because of a NULL pointer dereference. nvmet: failed to install queue 0 cntlid 1 ret 6 Unable to handle kernel NULL pointer dereference at virtual address 0000000000000008 Fix the bug by setting queue->nr_cmds to zero in case nvmet_tcp_alloc_cmd() fails. Fixes: 872d26a391da ("nvmet-tcp: add NVMe over TCP target driver") Signed-off-by: Maurizio Lombardi <mlombard@redhat.com> Reviewed-by: Christoph Hellwig <hch@lst.de> Signed-off-by: Keith Busch <kbusch@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
2024-09-12clk: qcom: ipq9574: Update the alpha PLL type for GPLLsdevi priya
[ Upstream commit 6357efe3abead68048729adf11a9363881657939 ] Update PLL offsets to DEFAULT_EVO to configure MDIO to 800MHz. The incorrect clock frequency leads to an incorrect MDIO clock. This, in turn, affects the MDIO hardware configurations as the divider is calculated from the MDIO clock frequency. If the clock frequency is not as expected, the MDIO register fails due to the generation of an incorrect MDIO frequency. This issue is critical as it results in incorrect MDIO configurations and ultimately leads to the MDIO function not working. This results in a complete feature failure affecting all Ethernet PHYs. Specifically, Ethernet will not work on IPQ9574 due to this issue. Currently, the clock frequency is set to CLK_ALPHA_PLL_TYPE_DEFAULT. However, this setting does not yield the expected clock frequency. To rectify this, we need to change this to CLK_ALPHA_PLL_TYPE_DEFAULT_EVO. This modification ensures that the clock frequency aligns with our expectations, thereby resolving the MDIO register failure and ensuring the proper functioning of the Ethernet on IPQ9574. Fixes: d75b82cff488 ("clk: qcom: Add Global Clock Controller driver for IPQ9574") Signed-off-by: devi priya <quic_devipriy@quicinc.com> Signed-off-by: Amandeep Singh <quic_amansing@quicinc.com> Link: https://lore.kernel.org/r/20240806061105.2849944-1-quic_amansing@quicinc.com Signed-off-by: Bjorn Andersson <andersson@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
2024-09-12crypto: starfive - Fix nent assignment in rsa decJia Jie Ho
[ Upstream commit 8323c036789b8b4a61925fce439a89dba17b7f2f ] Missing src scatterlist nent assignment in rsa decrypt function. Removing all unneeded assignment and use nents value from req->src instead. Signed-off-by: Jia Jie Ho <jiajie.ho@starfivetech.com> Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au> Signed-off-by: Sasha Levin <sashal@kernel.org>
2024-09-12crypto: starfive - Align rsa input data to 32-bitJia Jie Ho
[ Upstream commit 6aad7019f697ab0bed98eba737d19bd7f67713de ] Hardware expects RSA input plain/ciphertext to be 32-bit aligned. Set fixed length for preallocated buffer to the maximum supported keysize of the hardware and shift input text accordingly. Signed-off-by: Jia Jie Ho <jiajie.ho@starfivetech.com> Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au> Signed-off-by: Sasha Levin <sashal@kernel.org>
2024-09-12ata: libata-scsi: Check ATA_QCFLAG_RTF_FILLED before using result_tfIgor Pylypiv
[ Upstream commit 816be86c7993d3c5832c3017c0056297e86f978c ] qc->result_tf contents are only valid when the ATA_QCFLAG_RTF_FILLED flag is set. The ATA_QCFLAG_RTF_FILLED flag should be always set for commands that failed or for commands that have the ATA_QCFLAG_RESULT_TF flag set. Reviewed-by: Hannes Reinecke <hare@suse.de> Reviewed-by: Damien Le Moal <dlemoal@kernel.org> Reviewed-by: Niklas Cassel <cassel@kernel.org> Signed-off-by: Igor Pylypiv <ipylypiv@google.com> Link: https://lore.kernel.org/r/20240702024735.1152293-8-ipylypiv@google.com Signed-off-by: Niklas Cassel <cassel@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
2024-09-12ata: libata-scsi: Remove redundant sense_buffer memsetsIgor Pylypiv
[ Upstream commit 3f6d903b54a137e9e438d9c3b774b5d0432917bc ] SCSI layer clears sense_buffer in scsi_queue_rq() so there is no need for libata to clear it again. Reviewed-by: Hannes Reinecke <hare@suse.de> Reviewed-by: Damien Le Moal <dlemoal@kernel.org> Reviewed-by: Niklas Cassel <cassel@kernel.org> Signed-off-by: Igor Pylypiv <ipylypiv@google.com> Link: https://lore.kernel.org/r/20240702024735.1152293-5-ipylypiv@google.com Signed-off-by: Niklas Cassel <cassel@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
2024-09-12drm/amdgpu: handle gfx12 in amdgpu_display_verify_sizesMarek Olšák
[ Upstream commit 8dd1426e2c80e32ac1995007330c8f95ffa28ebb ] It verified GFX9-11 swizzle modes on GFX12, which has undefined behavior. Signed-off-by: Marek Olšák <marek.olsak@amd.com> Acked-by: Alex Deucher <alexander.deucher@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
2024-09-12can: mcp251xfd: rx: add workaround for erratum DS80000789E 6 of mcp2518fdMarc Kleine-Budde
[ Upstream commit 24436be590c6fbb05f6161b0dfba7d9da60214aa ] This patch tries to works around erratum DS80000789E 6 of the mcp2518fd, the other variants of the chip family (mcp2517fd and mcp251863) are probably also affected. In the bad case, the driver reads a too large head index. In the original code, the driver always trusted the read value, which caused old, already processed CAN frames or new, incompletely written CAN frames to be (re-)processed. To work around this issue, keep a per FIFO timestamp [1] of the last valid received CAN frame and compare against the timestamp of every received CAN frame. If an old CAN frame is detected, abort the iteration and mark the number of valid CAN frames as processed in the chip by incrementing the FIFO's tail index. Further tests showed that this workaround can recognize old CAN frames, but a small time window remains in which partially written CAN frames [2] are not recognized but then processed. These CAN frames have the correct data and time stamps, but the DLC has not yet been updated. [1] As the raw timestamp overflows every 107 seconds (at the usual clock rate of 40 MHz) convert it to nanoseconds with the timecounter framework and use this to detect stale CAN frames. Link: https://lore.kernel.org/all/BL3PR11MB64844C1C95CA3BDADAE4D8CCFBC99@BL3PR11MB6484.namprd11.prod.outlook.com [2] Reported-by: Stefan Althöfer <Stefan.Althoefer@janztec.com> Closes: https://lore.kernel.org/all/FR0P281MB1966273C216630B120ABB6E197E89@FR0P281MB1966.DEUP281.PROD.OUTLOOK.COM Tested-by: Stefan Althöfer <Stefan.Althoefer@janztec.com> Tested-by: Thomas Kopp <thomas.kopp@microchip.com> Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de> Signed-off-by: Sasha Levin <sashal@kernel.org>
2024-09-12can: mcp251xfd: clarify the meaning of timestampMarc Kleine-Budde
[ Upstream commit e793c724b48ca8cae9693bc3be528e85284c126a ] The mcp251xfd chip is configured to provide a timestamp with each received and transmitted CAN frame. The timestamp is derived from the internal free-running timer, which can also be read from the TBC register via SPI. The timer is 32 bits wide and is clocked by the external oscillator (typically 20 or 40 MHz). To avoid confusion, we call this timestamp "timestamp_raw" or "ts_raw" for short. Using the timecounter framework, the "ts_raw" is converted to 64 bit nanoseconds since the epoch. This is what we call "timestamp". This is a preparation for the next patches which use the "timestamp" to work around a bug where so far only the "ts_raw" is used. Tested-by: Stefan Althöfer <Stefan.Althoefer@janztec.com> Tested-by: Thomas Kopp <thomas.kopp@microchip.com> Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de> Signed-off-by: Sasha Levin <sashal@kernel.org>
2024-09-12can: mcp251xfd: rx: prepare to workaround broken RX FIFO head index erratumMarc Kleine-Budde
[ Upstream commit 85505e585637a737e4713c1386c30e37c325b82e ] This is a preparatory patch to work around erratum DS80000789E 6 of the mcp2518fd, the other variants of the chip family (mcp2517fd and mcp251863) are probably also affected. When handling the RX interrupt, the driver iterates over all pending FIFOs (which are implemented as ring buffers in hardware) and reads the FIFO header index from the RX FIFO STA register of the chip. In the bad case, the driver reads a too large head index. In the original code, the driver always trusted the read value, which caused old CAN frames that were already processed, or new, incompletely written CAN frames to be (re-)processed. Instead of reading and trusting the head index, read the head index and calculate the number of CAN frames that were supposedly received - replace mcp251xfd_rx_ring_update() with mcp251xfd_get_rx_len(). The mcp251xfd_handle_rxif_ring() function reads the received CAN frames from the chip, iterates over them and pushes them into the network stack. Prepare that the iteration can be stopped if an old CAN frame is detected. The actual code to detect old or incomplete frames and abort will be added in the next patch. Link: https://lore.kernel.org/all/BL3PR11MB64844C1C95CA3BDADAE4D8CCFBC99@BL3PR11MB6484.namprd11.prod.outlook.com Reported-by: Stefan Althöfer <Stefan.Althoefer@janztec.com> Closes: https://lore.kernel.org/all/FR0P281MB1966273C216630B120ABB6E197E89@FR0P281MB1966.DEUP281.PROD.OUTLOOK.COM Tested-by: Stefan Althöfer <Stefan.Althoefer@janztec.com> Tested-by: Thomas Kopp <thomas.kopp@microchip.com> Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de> Signed-off-by: Sasha Levin <sashal@kernel.org>
2024-09-12can: mcp251xfd: mcp251xfd_handle_rxif_ring_uinc(): factor out in separate ↵Marc Kleine-Budde
function [ Upstream commit d49184b7b585f9da7ee546b744525f62117019f6 ] This is a preparation patch. Sending the UINC messages followed by incrementing the tail pointer will be called in more than one place in upcoming patches, so factor this out into a separate function. Also make mcp251xfd_handle_rxif_ring_uinc() safe to be called with a "len" of 0. Tested-by: Stefan Althöfer <Stefan.Althoefer@janztec.com> Tested-by: Thomas Kopp <thomas.kopp@microchip.com> Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de> Signed-off-by: Sasha Levin <sashal@kernel.org>
2024-09-12ACPI: processor: Fix memory leaks in error paths of processor_add()Jonathan Cameron
[ Upstream commit 47ec9b417ed9b6b8ec2a941cd84d9de62adc358a ] If acpi_processor_get_info() returned an error, pr and the associated pr->throttling.shared_cpu_map were leaked. The unwind code was in the wrong order wrt to setup, relying on some unwind actions having no affect (clearing variables that were never set etc). That makes it harder to reason about so reorder and add appropriate labels to only undo what was actually set up in the first place. Acked-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com> Reviewed-by: Gavin Shan <gshan@redhat.com> Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com> Link: https://lore.kernel.org/r/20240529133446.28446-6-Jonathan.Cameron@huawei.com Signed-off-by: Catalin Marinas <catalin.marinas@arm.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
2024-09-12ACPI: processor: Return an error if acpi_processor_get_info() fails in ↵Jonathan Cameron
processor_add() [ Upstream commit fadf231f0a06a6748a7fc4a2c29ac9ef7bca6bfd ] Rafael observed [1] that returning 0 from processor_add() will result in acpi_default_enumeration() being called which will attempt to create a platform device, but that makes little sense when the processor is known to be not available. So just return the error code from acpi_processor_get_info() instead. Link: https://lore.kernel.org/all/CAJZ5v0iKU8ra9jR+EmgxbuNm=Uwx2m1-8vn_RAZ+aCiUVLe3Pw@mail.gmail.com/ [1] Suggested-by: Rafael J. Wysocki <rafael@kernel.org> Acked-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com> Reviewed-by: Gavin Shan <gshan@redhat.com> Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com> Link: https://lore.kernel.org/r/20240529133446.28446-5-Jonathan.Cameron@huawei.com Signed-off-by: Catalin Marinas <catalin.marinas@arm.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
2024-09-12clocksource/drivers/timer-of: Remove percpu irq related codeDaniel Lezcano
commit 471ef0b5a8aaca4296108e756b970acfc499ede4 upstream. GCC's named address space checks errors out with: drivers/clocksource/timer-of.c: In function ‘timer_of_irq_exit’: drivers/clocksource/timer-of.c:29:46: error: passing argument 2 of ‘free_percpu_irq’ from pointer to non-enclosed address space 29 | free_percpu_irq(of_irq->irq, clkevt); | ^~~~~~ In file included from drivers/clocksource/timer-of.c:8: ./include/linux/interrupt.h:201:43: note: expected ‘__seg_gs void *’ but argument is of type ‘struct clock_event_device *’ 201 | extern void free_percpu_irq(unsigned int, void __percpu *); | ^~~~~~~~~~~~~~~ drivers/clocksource/timer-of.c: In function ‘timer_of_irq_init’: drivers/clocksource/timer-of.c:74:51: error: passing argument 4 of ‘request_percpu_irq’ from pointer to non-enclosed address space 74 | np->full_name, clkevt) : | ^~~~~~ ./include/linux/interrupt.h:190:56: note: expected ‘__seg_gs void *’ but argument is of type ‘struct clock_event_device *’ 190 | const char *devname, void __percpu *percpu_dev_id) Sparse warns about: timer-of.c:29:46: warning: incorrect type in argument 2 (different address spaces) timer-of.c:29:46: expected void [noderef] __percpu * timer-of.c:29:46: got struct clock_event_device *clkevt timer-of.c:74:51: warning: incorrect type in argument 4 (different address spaces) timer-of.c:74:51: expected void [noderef] __percpu *percpu_dev_id timer-of.c:74:51: got struct clock_event_device *clkevt It appears the code is incorrect as reported by Uros Bizjak: "The referred code is questionable as it tries to reuse the clkevent pointer once as percpu pointer and once as generic pointer, which should be avoided." This change removes the percpu related code as no drivers is using it. [Daniel: Fixed the description] Fixes: dc11bae785295 ("clocksource/drivers: Add timer-of common init routine") Reported-by: Uros Bizjak <ubizjak@gmail.com> Tested-by: Uros Bizjak <ubizjak@gmail.com> Link: https://lore.kernel.org/r/20240819100335.2394751-1-daniel.lezcano@linaro.org Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2024-09-12clocksource/drivers/imx-tpm: Fix next event not taking effect sometimeJacky Bai
commit 3d5c2f8e75a55cfb11a85086c71996af0354a1fb upstream. The value written into the TPM CnV can only be updated into the hardware when the counter increases. Additional writes to the CnV write buffer are ignored until the register has been updated. Therefore, we need to check if the CnV has been updated before continuing. This may require waiting for 1 counter cycle in the worst case. Cc: stable@vger.kernel.org Fixes: 059ab7b82eec ("clocksource/drivers/imx-tpm: Add imx tpm timer support") Signed-off-by: Jacky Bai <ping.bai@nxp.com> Reviewed-by: Peng Fan <peng.fan@nxp.com> Reviewed-by: Ye Li <ye.li@nxp.com> Reviewed-by: Jason Liu <jason.hui.liu@nxp.com> Signed-off-by: Frank Li <Frank.Li@nxp.com> Link: https://lore.kernel.org/r/20240725193355.1436005-2-Frank.Li@nxp.com Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2024-09-12clocksource/drivers/imx-tpm: Fix return -ETIME when delta exceeds INT_MAXJacky Bai
commit 5b8843fcd49827813da80c0f590a17ae4ce93c5d upstream. In tpm_set_next_event(delta), return -ETIME by wrong cast to int when delta is larger than INT_MAX. For example: tpm_set_next_event(delta = 0xffff_fffe) { ... next = tpm_read_counter(); // assume next is 0x10 next += delta; // next will 0xffff_fffe + 0x10 = 0x1_0000_000e now = tpm_read_counter(); // now is 0x10 ... return (int)(next - now) <= 0 ? -ETIME : 0; ^^^^^^^^^^ 0x1_0000_000e - 0x10 = 0xffff_fffe, which is -2 when cast to int. So return -ETIME. } To fix this, introduce a 'prev' variable and check if 'now - prev' is larger than delta. Cc: stable@vger.kernel.org Fixes: 059ab7b82eec ("clocksource/drivers/imx-tpm: Add imx tpm timer support") Signed-off-by: Jacky Bai <ping.bai@nxp.com> Reviewed-by: Peng Fan <peng.fan@nxp.com> Reviewed-by: Ye Li <ye.li@nxp.com> Reviewed-by: Jason Liu <jason.hui.liu@nxp.com> Signed-off-by: Frank Li <Frank.Li@nxp.com> Link: https://lore.kernel.org/r/20240725193355.1436005-1-Frank.Li@nxp.com Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2024-09-12VMCI: Fix use-after-free when removing resource in vmci_resource_remove()David Fernandez Gonzalez
commit 48b9a8dabcc3cf5f961b2ebcd8933bf9204babb7 upstream. When removing a resource from vmci_resource_table in vmci_resource_remove(), the search is performed using the resource handle by comparing context and resource fields. It is possible though to create two resources with different types but same handle (same context and resource fields). When trying to remove one of the resources, vmci_resource_remove() may not remove the intended one, but the object will still be freed as in the case of the datagram type in vmci_datagram_destroy_handle(). vmci_resource_table will still hold a pointer to this freed resource leading to a use-after-free vulnerability. BUG: KASAN: use-after-free in vmci_handle_is_equal include/linux/vmw_vmci_defs.h:142 [inline] BUG: KASAN: use-after-free in vmci_resource_remove+0x3a1/0x410 drivers/misc/vmw_vmci/vmci_resource.c:147 Read of size 4 at addr ffff88801c16d800 by task syz-executor197/1592 Call Trace: <TASK> __dump_stack lib/dump_stack.c:88 [inline] dump_stack_lvl+0x82/0xa9 lib/dump_stack.c:106 print_address_description.constprop.0+0x21/0x366 mm/kasan/report.c:239 __kasan_report.cold+0x7f/0x132 mm/kasan/report.c:425 kasan_report+0x38/0x51 mm/kasan/report.c:442 vmci_handle_is_equal include/linux/vmw_vmci_defs.h:142 [inline] vmci_resource_remove+0x3a1/0x410 drivers/misc/vmw_vmci/vmci_resource.c:147 vmci_qp_broker_detach+0x89a/0x11b9 drivers/misc/vmw_vmci/vmci_queue_pair.c:2182 ctx_free_ctx+0x473/0xbe1 drivers/misc/vmw_vmci/vmci_context.c:444 kref_put include/linux/kref.h:65 [inline] vmci_ctx_put drivers/misc/vmw_vmci/vmci_context.c:497 [inline] vmci_ctx_destroy+0x170/0x1d6 drivers/misc/vmw_vmci/vmci_context.c:195 vmci_host_close+0x125/0x1ac drivers/misc/vmw_vmci/vmci_host.c:143 __fput+0x261/0xa34 fs/file_table.c:282 task_work_run+0xf0/0x194 kernel/task_work.c:164 tracehook_notify_resume include/linux/tracehook.h:189 [inline] exit_to_user_mode_loop+0x184/0x189 kernel/entry/common.c:187 exit_to_user_mode_prepare+0x11b/0x123 kernel/entry/common.c:220 __syscall_exit_to_user_mode_work kernel/entry/common.c:302 [inline] syscall_exit_to_user_mode+0x18/0x42 kernel/entry/common.c:313 do_syscall_64+0x41/0x85 arch/x86/entry/common.c:86 entry_SYSCALL_64_after_hwframe+0x6e/0x0 This change ensures the type is also checked when removing the resource from vmci_resource_table in vmci_resource_remove(). Fixes: bc63dedb7d46 ("VMCI: resource object implementation.") Cc: stable@vger.kernel.org Reported-by: George Kennedy <george.kennedy@oracle.com> Signed-off-by: David Fernandez Gonzalez <david.fernandez.gonzalez@oracle.com> Link: https://lore.kernel.org/r/20240828154338.754746-1-david.fernandez.gonzalez@oracle.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2024-09-12Drivers: hv: vmbus: Fix rescind handling in uio_hv_genericNaman Jain
commit 6fd28941447bf2c8ca0f26fda612a1cabc41663f upstream. Rescind offer handling relies on rescind callbacks for some of the resources cleanup, if they are registered. It does not unregister vmbus device for the primary channel closure, when callback is registered. Without it, next onoffer does not come, rescind flag remains set and device goes to unusable state. Add logic to unregister vmbus for the primary channel in rescind callback to ensure channel removal and relid release, and to ensure that next onoffer can be received and handled properly. Cc: stable@vger.kernel.org Fixes: ca3cda6fcf1e ("uio_hv_generic: add rescind support") Signed-off-by: Naman Jain <namjain@linux.microsoft.com> Reviewed-by: Saurabh Sengar <ssengar@linux.microsoft.com> Link: https://lore.kernel.org/r/20240829071312.1595-3-namjain@linux.microsoft.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2024-09-12uio_hv_generic: Fix kernel NULL pointer dereference in hv_uio_rescindSaurabh Sengar
commit fb1adbd7e50f3d2de56d0a2bb0700e2e819a329e upstream. For primary VM Bus channels, primary_channel pointer is always NULL. This pointer is valid only for the secondary channels. Also, rescind callback is meant for primary channels only. Fix NULL pointer dereference by retrieving the device_obj from the parent for the primary channel. Cc: stable@vger.kernel.org Fixes: ca3cda6fcf1e ("uio_hv_generic: add rescind support") Signed-off-by: Saurabh Sengar <ssengar@linux.microsoft.com> Signed-off-by: Naman Jain <namjain@linux.microsoft.com> Link: https://lore.kernel.org/r/20240829071312.1595-2-namjain@linux.microsoft.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2024-09-12nvmem: Fix return type of devm_nvmem_device_get() in kerneldocGeert Uytterhoeven
commit c69f37f6559a8948d70badd2b179db7714dedd62 upstream. devm_nvmem_device_get() returns an nvmem device, not an nvmem cell. Fixes: e2a5402ec7c6d044 ("nvmem: Add nvmem_device based consumer apis.") Cc: stable <stable@kernel.org> Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be> Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org> Link: https://lore.kernel.org/r/20240902142510.71096-3-srinivas.kandagatla@linaro.org Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2024-09-12binder: fix UAF caused by offsets overwriteCarlos Llamas
commit 4df153652cc46545722879415937582028c18af5 upstream. Binder objects are processed and copied individually into the target buffer during transactions. Any raw data in-between these objects is copied as well. However, this raw data copy lacks an out-of-bounds check. If the raw data exceeds the data section size then the copy overwrites the offsets section. This eventually triggers an error that attempts to unwind the processed objects. However, at this point the offsets used to index these objects are now corrupted. Unwinding with corrupted offsets can result in decrements of arbitrary nodes and lead to their premature release. Other users of such nodes are left with a dangling pointer triggering a use-after-free. This issue is made evident by the following KASAN report (trimmed): ================================================================== BUG: KASAN: slab-use-after-free in _raw_spin_lock+0xe4/0x19c Write of size 4 at addr ffff47fc91598f04 by task binder-util/743 CPU: 9 UID: 0 PID: 743 Comm: binder-util Not tainted 6.11.0-rc4 #1 Hardware name: linux,dummy-virt (DT) Call trace: _raw_spin_lock+0xe4/0x19c binder_free_buf+0x128/0x434 binder_thread_write+0x8a4/0x3260 binder_ioctl+0x18f0/0x258c [...] Allocated by task 743: __kmalloc_cache_noprof+0x110/0x270 binder_new_node+0x50/0x700 binder_transaction+0x413c/0x6da8 binder_thread_write+0x978/0x3260 binder_ioctl+0x18f0/0x258c [...] Freed by task 745: kfree+0xbc/0x208 binder_thread_read+0x1c5c/0x37d4 binder_ioctl+0x16d8/0x258c [...] ================================================================== To avoid this issue, let's check that the raw data copy is within the boundaries of the data section. Fixes: 6d98eb95b450 ("binder: avoid potential data leakage when copying txn") Cc: Todd Kjos <tkjos@google.com> Cc: stable@vger.kernel.org Signed-off-by: Carlos Llamas <cmllamas@google.com> Link: https://lore.kernel.org/r/20240822182353.2129600-1-cmllamas@google.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2024-09-12misc: fastrpc: Fix double free of 'buf' in error pathSukrut Bellary
commit e8c276d4dc0e19ee48385f74426aebc855b49aaf upstream. smatch warning: drivers/misc/fastrpc.c:1926 fastrpc_req_mmap() error: double free of 'buf' In fastrpc_req_mmap() error path, the fastrpc buffer is freed in fastrpc_req_munmap_impl() if unmap is successful. But in the end, there is an unconditional call to fastrpc_buf_free(). So the above case triggers the double free of fastrpc buf. Fixes: 72fa6f7820c4 ("misc: fastrpc: Rework fastrpc_req_munmap") Reviewed-by: Shuah Khan <skhan@linuxfoundation.org> Reviewed-by: Dan Carpenter <dan.carpenter@linaro.org> Reviewed-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org> Signed-off-by: Sukrut Bellary <sukrut.bellary@linux.com> Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org> Cc: stable <stable@kernel.org> Link: https://lore.kernel.org/r/20240902141409.70371-2-srinivas.kandagatla@linaro.org Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2024-09-12usb: dwc3: Avoid waking up gadget during startxferPrashanth K
commit 00dcf2fa449f23a263343d7fe051741bdde65d0b upstream. When operating in High-Speed, it is observed that DSTS[USBLNKST] doesn't update link state immediately after receiving the wakeup interrupt. Since wakeup event handler calls the resume callbacks, there is a chance that function drivers can perform an ep queue, which in turn tries to perform remote wakeup from send_gadget_ep_cmd(STARTXFER). This happens because DSTS[[21:18] wasn't updated to U0 yet, it's observed that the latency of DSTS can be in order of milli-seconds. Hence avoid calling gadget_wakeup during startxfer to prevent unnecessarily issuing remote wakeup to host. Fixes: c36d8e947a56 ("usb: dwc3: gadget: put link to U0 before Start Transfer") Cc: stable@vger.kernel.org Suggested-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com> Signed-off-by: Prashanth K <quic_prashk@quicinc.com> Acked-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com> Link: https://lore.kernel.org/r/20240828064302.3796315-1-quic_prashk@quicinc.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2024-09-12usb: cdns2: Fix controller reset issuePawel Laszczak
commit e2940928115e83d707b21bf00b0db7d6c15f8341 upstream. Patch fixes the procedure of resetting controller. The CPUCTRL register is write only and reading returns 0. Waiting for reset to complite is incorrect. Fixes: 3eb1f1efe204 ("usb: cdns2: Add main part of Cadence USBHS driver") cc: stable@vger.kernel.org Signed-off-by: Pawel Laszczak <pawell@cadence.com> Link: https://lore.kernel.org/r/PH7PR07MB9538D56D75F1F399D0BB96F0DD922@PH7PR07MB9538.namprd07.prod.outlook.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2024-09-12usb: dwc3: core: update LC timer as per USB Spec V3.2Faisal Hassan
commit 9149c9b0c7e046273141e41eebd8a517416144ac upstream. This fix addresses STAR 9001285599, which only affects DWC_usb3 version 3.20a. The timer value for PM_LC_TIMER in DWC_usb3 3.20a for the Link ECN changes is incorrect. If the PM TIMER ECN is enabled via GUCTL2[19], the link compliance test (TD7.21) may fail. If the ECN is not enabled (GUCTL2[19] = 0), the controller will use the old timer value (5us), which is still acceptable for the link compliance test. Therefore, clear GUCTL2[19] to pass the USB link compliance test: TD 7.21. Cc: stable@vger.kernel.org Signed-off-by: Faisal Hassan <quic_faisalh@quicinc.com> Acked-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com> Link: https://lore.kernel.org/r/20240829094502.26502-1-quic_faisalh@quicinc.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2024-09-12iio: adc: ad7124: fix chip ID mismatchDumitru Ceclan
commit 96f9ab0d5933c1c00142dd052f259fce0bc3ced2 upstream. The ad7124_soft_reset() function has the assumption that the chip will assert the "power-on reset" bit in the STATUS register after a software reset without any delay. The POR bit =0 is used to check if the chip initialization is done. A chip ID mismatch probe error appears intermittently when the probe continues too soon and the ID register does not contain the expected value. Fix by adding a 200us delay after the software reset command is issued. Fixes: b3af341bbd96 ("iio: adc: Add ad7124 support") Signed-off-by: Dumitru Ceclan <dumitru.ceclan@analog.com> Reviewed-by: Nuno Sa <nuno.sa@analog.com> Link: https://patch.msgid.link/20240731-ad7124-fix-v1-1-46a76aa4b9be@analog.com Cc: <Stable@vger.kernel.org> Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2024-09-12iio: adc: ad7606: remove frstdata check for serial modeGuillaume Stols
commit 90826e08468ba7fb35d8b39645b22d9e80004afe upstream. The current implementation attempts to recover from an eventual glitch in the clock by checking frstdata state after reading the first channel's sample: If frstdata is low, it will reset the chip and return -EIO. This will only work in parallel mode, where frstdata pin is set low after the 2nd sample read starts. For the serial mode, according to the datasheet, "The FRSTDATA output returns to a logic low following the 16th SCLK falling edge.", thus after the Xth pulse, X being the number of bits in a sample, the check will always be true, and the driver will not work at all in serial mode if frstdata(optional) is defined in the devicetree as it will reset the chip, and return -EIO every time read_sample is called. Hence, this check must be removed for serial mode. Fixes: b9618c0cacd7 ("staging: IIO: ADC: New driver for AD7606/AD7606-6/AD7606-4") Signed-off-by: Guillaume Stols <gstols@baylibre.com> Reviewed-by: Nuno Sa <nuno.sa@analog.com> Link: https://patch.msgid.link/20240702-cleanup-ad7606-v3-1-18d5ea18770e@baylibre.com Cc: <Stable@vger.kernel.org> Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2024-09-12iio: adc: ad7124: fix config comparisonDumitru Ceclan
commit 2f6b92d0f69f04d9e2ea0db1228ab7f82f3173af upstream. The ad7124_find_similar_live_cfg() computes the compare size by substracting the address of the cfg struct from the address of the live field. Because the live field is the first field in the struct, the result is 0. Also, the memcmp() call is made from the start of the cfg struct, which includes the live and cfg_slot fields, which are not relevant for the comparison. Fix by grouping the relevant fields with struct_group() and use the size of the group to compute the compare size; make the memcmp() call from the address of the group. Fixes: 7b8d045e497a ("iio: adc: ad7124: allow more than 8 channels") Signed-off-by: Dumitru Ceclan <dumitru.ceclan@analog.com> Reviewed-by: Nuno Sa <nuno.sa@analog.com> Link: https://patch.msgid.link/20240731-ad7124-fix-v1-2-46a76aa4b9be@analog.com Cc: <Stable@vger.kernel.org> Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2024-09-12iio: fix scale application in iio_convert_raw_to_processed_unlockedMatteo Martelli
commit 8a3dcc970dc57b358c8db2702447bf0af4e0d83a upstream. When the scale_type is IIO_VAL_INT_PLUS_MICRO or IIO_VAL_INT_PLUS_NANO the scale passed as argument is only applied to the fractional part of the value. Fix it by also multiplying the integer part by the scale provided. Fixes: 48e44ce0f881 ("iio:inkern: Add function to read the processed value") Signed-off-by: Matteo Martelli <matteomartelli3@gmail.com> Link: https://patch.msgid.link/20240730-iio-fix-scale-v1-1-6246638c8daa@gmail.com Cc: <Stable@vger.kernel.org> Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2024-09-12iio: buffer-dmaengine: fix releasing dma channel on errorDavid Lechner
commit 84c65d8008764a8fb4e627ff02de01ec4245f2c4 upstream. If dma_get_slave_caps() fails, we need to release the dma channel before returning an error to avoid leaking the channel. Fixes: 2d6ca60f3284 ("iio: Add a DMAengine framework based buffer") Signed-off-by: David Lechner <dlechner@baylibre.com> Link: https://patch.msgid.link/20240723-iio-fix-dmaengine-free-on-error-v1-1-2c7cbc9b92ff@baylibre.com Cc: <Stable@vger.kernel.org> Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
generated by cgit v1.2.3 (git 2.39.1) at 2025-07-31 15:24:05 +0000