| Age | Commit message (Collapse) | Author |
|---|
|
commit 1f311c94aabdb419c28e3147bcc8ab89269f1a7e upstream.
SD spec definition:
"Host provides at least 74 Clocks before issuing first command"
After 1ms for the voltage stable then start issuing the Clock signals
if POWER STATE is
MMC_POWER_OFF to MMC_POWER_UP to issue Clock signal to card
MMC_POWER_UP to MMC_POWER_ON to stop issuing signal to card
Signed-off-by: Ricky Wu <ricky_wu@realtek.com>
Link: https://lore.kernel.org/r/1badf10aba764191a1a752edcbf90389@realtek.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Ricky Wu <ricky_wu@realtek.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Christian Loehle <cloehle@hyperstone.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 2873d4d52f7c52d60b316ba6c47bd7122b5a9861 upstream.
The previous split budget between TX and RX made it return not using
the entire budget but at the same time not having calling called
napi_complete. This sometimes led to the poll to not be called, and at
the same time having TX and RX interrupts disabled resulting in the
driver getting stuck.
Fixes: 6cec9b07fe6a ("can: grcan: Add device driver for GRCAN and GRHCAN cores")
Link: https://lore.kernel.org/all/20220429084656.29788-4-andreas@gaisler.com
Cc: stable@vger.kernel.org
Signed-off-by: Andreas Larsson <andreas@gaisler.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
needs
commit 1e93ed26acf03fe6c97c6d573a10178596aadd43 upstream.
The systemid property was checked for in the wrong place of the device
tree and compared to the wrong value.
Fixes: 6cec9b07fe6a ("can: grcan: Add device driver for GRCAN and GRHCAN cores")
Link: https://lore.kernel.org/all/20220429084656.29788-3-andreas@gaisler.com
Cc: stable@vger.kernel.org
Signed-off-by: Andreas Larsson <andreas@gaisler.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 1f1e87b4dc4598eac57a69868534b92d65e47e82 upstream.
Fixes the following W=1 kernel build warning(s):
from drivers/block/drbd/drbd_nl.c:24:
drivers/block/drbd/drbd_nl.c: In function ‘drbd_adm_set_role’:
drivers/block/drbd/drbd_nl.c:793:11: warning: implicit conversion from ‘enum drbd_state_rv’ to ‘enum drbd_ret_code’ [-Wenum-conversion]
drivers/block/drbd/drbd_nl.c:795:11: warning: implicit conversion from ‘enum drbd_state_rv’ to ‘enum drbd_ret_code’ [-Wenum-conversion]
drivers/block/drbd/drbd_nl.c: In function ‘drbd_adm_attach’:
drivers/block/drbd/drbd_nl.c:1965:10: warning: implicit conversion from ‘enum drbd_state_rv’ to ‘enum drbd_ret_code’ [-Wenum-conversion]
drivers/block/drbd/drbd_nl.c: In function ‘drbd_adm_connect’:
drivers/block/drbd/drbd_nl.c:2690:10: warning: implicit conversion from ‘enum drbd_state_rv’ to ‘enum drbd_ret_code’ [-Wenum-conversion]
drivers/block/drbd/drbd_nl.c: In function ‘drbd_adm_disconnect’:
drivers/block/drbd/drbd_nl.c:2803:11: warning: implicit conversion from ‘enum drbd_state_rv’ to ‘enum drbd_ret_code’ [-Wenum-conversion]
Cc: Philipp Reisner <philipp.reisner@linbit.com>
Cc: Lars Ellenberg <lars.ellenberg@linbit.com>
Cc: Jens Axboe <axboe@kernel.dk>
Cc: drbd-dev@lists.linbit.com
Cc: linux-block@vger.kernel.org
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Link: https://lore.kernel.org/r/20210312105530.2219008-8-lee.jones@linaro.org
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Cc: Nathan Chancellor <nathan@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 9f6dc633761006f974701d4c88da71ab68670749 upstream.
Commit d208b89401e0 ("dm: fix mempool NULL pointer race when
completing IO") didn't go far enough.
When bio_end_io_acct ends the count of in-flight I/Os may reach zero
and the DM device may be suspended. There is a possibility that the
suspend races with dm_stats_account_io.
Fix this by adding percpu "pending_io" counters to track outstanding
dm_io. Move kicking of suspend queue to dm_io_dec_pending(). Also,
rename md_in_flight_bios() to dm_in_flight_bios() and update it to
iterate all pending_io counters.
Fixes: d208b89401e0 ("dm: fix mempool NULL pointer race when completing IO")
Cc: stable@vger.kernel.org
Co-developed-by: Mikulas Patocka <mpatocka@redhat.com>
Signed-off-by: Mikulas Patocka <mpatocka@redhat.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Signed-off-by: Mikulas Patocka <mpatocka@redhat.com>
Reviewed-by: Mike Snitzer <snitzer@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit d208b89401e073de986dc891037c5a668f5d5d95 upstream.
dm_io_dec_pending() calls end_io_acct() first and will then dec md
in-flight pending count. But if a task is swapping DM table at same
time this can result in a crash due to mempool->elements being NULL:
task1 task2
do_resume
->do_suspend
->dm_wait_for_completion
bio_endio
->clone_endio
->dm_io_dec_pending
->end_io_acct
->wakeup task1
->dm_swap_table
->__bind
->__bind_mempools
->bioset_exit
->mempool_exit
->free_io
[ 67.330330] Unable to handle kernel NULL pointer dereference at
virtual address 0000000000000000
......
[ 67.330494] pstate: 80400085 (Nzcv daIf +PAN -UAO)
[ 67.330510] pc : mempool_free+0x70/0xa0
[ 67.330515] lr : mempool_free+0x4c/0xa0
[ 67.330520] sp : ffffff8008013b20
[ 67.330524] x29: ffffff8008013b20 x28: 0000000000000004
[ 67.330530] x27: ffffffa8c2ff40a0 x26: 00000000ffff1cc8
[ 67.330535] x25: 0000000000000000 x24: ffffffdada34c800
[ 67.330541] x23: 0000000000000000 x22: ffffffdada34c800
[ 67.330547] x21: 00000000ffff1cc8 x20: ffffffd9a1304d80
[ 67.330552] x19: ffffffdada34c970 x18: 000000b312625d9c
[ 67.330558] x17: 00000000002dcfbf x16: 00000000000006dd
[ 67.330563] x15: 000000000093b41e x14: 0000000000000010
[ 67.330569] x13: 0000000000007f7a x12: 0000000034155555
[ 67.330574] x11: 0000000000000001 x10: 0000000000000001
[ 67.330579] x9 : 0000000000000000 x8 : 0000000000000000
[ 67.330585] x7 : 0000000000000000 x6 : ffffff80148b5c1a
[ 67.330590] x5 : ffffff8008013ae0 x4 : 0000000000000001
[ 67.330596] x3 : ffffff80080139c8 x2 : ffffff801083bab8
[ 67.330601] x1 : 0000000000000000 x0 : ffffffdada34c970
[ 67.330609] Call trace:
[ 67.330616] mempool_free+0x70/0xa0
[ 67.330627] bio_put+0xf8/0x110
[ 67.330638] dec_pending+0x13c/0x230
[ 67.330644] clone_endio+0x90/0x180
[ 67.330649] bio_endio+0x198/0x1b8
[ 67.330655] dec_pending+0x190/0x230
[ 67.330660] clone_endio+0x90/0x180
[ 67.330665] bio_endio+0x198/0x1b8
[ 67.330673] blk_update_request+0x214/0x428
[ 67.330683] scsi_end_request+0x2c/0x300
[ 67.330688] scsi_io_completion+0xa0/0x710
[ 67.330695] scsi_finish_command+0xd8/0x110
[ 67.330700] scsi_softirq_done+0x114/0x148
[ 67.330708] blk_done_softirq+0x74/0xd0
[ 67.330716] __do_softirq+0x18c/0x374
[ 67.330724] irq_exit+0xb4/0xb8
[ 67.330732] __handle_domain_irq+0x84/0xc0
[ 67.330737] gic_handle_irq+0x148/0x1b0
[ 67.330744] el1_irq+0xe8/0x190
[ 67.330753] lpm_cpuidle_enter+0x4f8/0x538
[ 67.330759] cpuidle_enter_state+0x1fc/0x398
[ 67.330764] cpuidle_enter+0x18/0x20
[ 67.330772] do_idle+0x1b4/0x290
[ 67.330778] cpu_startup_entry+0x20/0x28
[ 67.330786] secondary_start_kernel+0x160/0x170
Fix this by:
1) Establishing pointers to 'struct dm_io' members in
dm_io_dec_pending() so that they may be passed into end_io_acct()
_after_ free_io() is called.
2) Moving end_io_acct() after free_io().
Cc: stable@vger.kernel.org
Signed-off-by: Jiazi Li <lijiazi@xiaomi.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Signed-off-by: Mikulas Patocka <mpatocka@redhat.com>
Reviewed-by: Mike Snitzer <snitzer@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 5ef9b803a4af0f5e42012176889b40bb2a978b18 upstream.
The AlphaProject AP-SH4A-3A/AP-SH4AD-0A SH boards use IRQ0 for their SMSC
LAN911x Ethernet chip, so the networking on them must have been broken by
commit 965b2aa78fbc ("net/smsc911x: fix irq resource allocation failure")
which filtered out 0 as well as the negative error codes -- it was kinda
correct at the time, as platform_get_irq() could return 0 on of_irq_get()
failure and on the actual 0 in an IRQ resource. This issue was fixed by
me (back in 2016!), so we should be able to fix this driver to allow IRQ0
usage again...
When merging this to the stable kernels, make sure you also merge commit
e330b9a6bb35 ("platform: don't return 0 from platform_get_irq[_byname]()
on error") -- that's my fix to platform_get_irq() for the DT platforms...
Fixes: 965b2aa78fbc ("net/smsc911x: fix irq resource allocation failure")
Signed-off-by: Sergey Shtylyov <s.shtylyov@omp.ru>
Link: https://lore.kernel.org/r/656036e4-6387-38df-b8a7-6ba683b16e63@omp.ru
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 7a6bc33ab54923d325d9a1747ec9652c4361ebd1 upstream.
check the return value of of_address_to_resource() and also add
missing of_node_put() for np and npp nodes.
Fixes: e0a3bc65448c ("net: emaclite: Support multiple phys connected to one MDIO bus")
Addresses-Coverity: Event check_return value.
Signed-off-by: Shravya Kumbham <shravya.kumbham@xilinx.com>
Signed-off-by: Radhey Shyam Pandey <radhey.shyam.pandey@xilinx.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 7b2666ce445c700b8dcee994da44ddcf050a0842 upstream.
When removing the adt7470 module, a warning might be printed:
do not call blocking ops when !TASK_RUNNING; state=1
set at [<ffffffffa006052b>] adt7470_update_thread+0x7b/0x130 [adt7470]
This happens because adt7470_update_thread() can leave the kthread in
TASK_INTERRUPTIBLE state when the kthread is being stopped before
the call of set_current_state(). Since kthread_exit() might sleep in
exit_signals(), the warning is printed.
Fix that by using schedule_timeout_interruptible() and removing
the call of set_current_state().
This causes TASK_INTERRUPTIBLE to be set after kthread_should_stop()
which might cause the kthread to exit.
Reported-by: Zheyu Ma <zheyuma97@gmail.com>
Fixes: 93cacfd41f82 (hwmon: (adt7470) Allow faster removal)
Signed-off-by: Armin Wolf <W_Armin@gmx.de>
Tested-by: Zheyu Ma <zheyuma97@gmail.com>
Link: https://lore.kernel.org/r/20220407101312.13331-1-W_Armin@gmx.de
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
nfcmrvl_nci_unregister_dev to avoid bugs
commit d270453a0d9ec10bb8a802a142fb1b3601a83098 upstream.
There are destructive operations such as nfcmrvl_fw_dnld_abort and
gpio_free in nfcmrvl_nci_unregister_dev. The resources such as firmware,
gpio and so on could be destructed while the upper layer functions such as
nfcmrvl_fw_dnld_start and nfcmrvl_nci_recv_frame is executing, which leads
to double-free, use-after-free and null-ptr-deref bugs.
There are three situations that could lead to double-free bugs.
The first situation is shown below:
(Thread 1) | (Thread 2)
nfcmrvl_fw_dnld_start |
... | nfcmrvl_nci_unregister_dev
release_firmware() | nfcmrvl_fw_dnld_abort
kfree(fw) //(1) | fw_dnld_over
| release_firmware
... | kfree(fw) //(2)
| ...
The second situation is shown below:
(Thread 1) | (Thread 2)
nfcmrvl_fw_dnld_start |
... |
mod_timer |
(wait a time) |
fw_dnld_timeout | nfcmrvl_nci_unregister_dev
fw_dnld_over | nfcmrvl_fw_dnld_abort
release_firmware | fw_dnld_over
kfree(fw) //(1) | release_firmware
... | kfree(fw) //(2)
The third situation is shown below:
(Thread 1) | (Thread 2)
nfcmrvl_nci_recv_frame |
if(..->fw_download_in_progress)|
nfcmrvl_fw_dnld_recv_frame |
queue_work |
|
fw_dnld_rx_work | nfcmrvl_nci_unregister_dev
fw_dnld_over | nfcmrvl_fw_dnld_abort
release_firmware | fw_dnld_over
kfree(fw) //(1) | release_firmware
| kfree(fw) //(2)
The firmware struct is deallocated in position (1) and deallocated
in position (2) again.
The crash trace triggered by POC is like below:
BUG: KASAN: double-free or invalid-free in fw_dnld_over
Call Trace:
kfree
fw_dnld_over
nfcmrvl_nci_unregister_dev
nci_uart_tty_close
tty_ldisc_kill
tty_ldisc_hangup
__tty_hangup.part.0
tty_release
...
What's more, there are also use-after-free and null-ptr-deref bugs
in nfcmrvl_fw_dnld_start. If we deallocate firmware struct, gpio or
set null to the members of priv->fw_dnld in nfcmrvl_nci_unregister_dev,
then, we dereference firmware, gpio or the members of priv->fw_dnld in
nfcmrvl_fw_dnld_start, the UAF or NPD bugs will happen.
This patch reorders destructive operations after nci_unregister_device
in order to synchronize between cleanup routine and firmware download
routine.
The nci_unregister_device is well synchronized. If the device is
detaching, the firmware download routine will goto error. If firmware
download routine is executing, nci_unregister_device will wait until
firmware download routine is finished.
Fixes: 3194c6870158 ("NFC: nfcmrvl: add firmware download support")
Signed-off-by: Duoming Zhou <duoming@zju.edu.cn>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 101da4268626b00d16356a6bf284d66e44c46ff9 upstream.
Use the device of the device tree node should be rather than the
device of the struct net_device when allocating DMA buffers.
The driver got away with it on sparc32 until commit 53b7670e5735
("sparc: factor the dma coherent mapping into helper") after which the
driver oopses.
Fixes: 6cec9b07fe6a ("can: grcan: Add device driver for GRCAN and GRHCAN cores")
Link: https://lore.kernel.org/all/20220429084656.29788-2-andreas@gaisler.com
Cc: stable@vger.kernel.org
Signed-off-by: Daniel Hellstrom <daniel@gaisler.com>
Signed-off-by: Andreas Larsson <andreas@gaisler.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 47f070a63e735bcc8d481de31be1b5a1aa62b31c upstream.
There are deadlocks caused by del_timer_sync(&priv->hang_timer) and
del_timer_sync(&priv->rr_timer) in grcan_close(), one of the deadlocks
are shown below:
(Thread 1) | (Thread 2)
| grcan_reset_timer()
grcan_close() | mod_timer()
spin_lock_irqsave() //(1) | (wait a time)
... | grcan_initiate_running_reset()
del_timer_sync() | spin_lock_irqsave() //(2)
(wait timer to stop) | ...
We hold priv->lock in position (1) of thread 1 and use
del_timer_sync() to wait timer to stop, but timer handler also need
priv->lock in position (2) of thread 2. As a result, grcan_close()
will block forever.
This patch extracts del_timer_sync() from the protection of
spin_lock_irqsave(), which could let timer handler to obtain the
needed lock.
Link: https://lore.kernel.org/all/20220425042400.66517-1-duoming@zju.edu.cn
Fixes: 6cec9b07fe6a ("can: grcan: Add device driver for GRCAN and GRHCAN cores")
Cc: stable@vger.kernel.org
Signed-off-by: Duoming Zhou <duoming@zju.edu.cn>
Reviewed-by: Andreas Larsson <andreas@gaisler.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit a7ecbe92b9243edbe94772f6f2c854e4142a3345 upstream.
card->local_node and card->bm_retries are both always accessed under
card->lock.
fw_core_handle_bus_reset has a check whose condition depends on
card->local_node and whose body writes to card->bm_retries.
Both of these accesses are not under card->lock. Move the lock acquiring
of card->lock to before this check such that these accesses do happen
when card->lock is held.
fw_destroy_nodes is called inside the check.
Since fw_destroy_nodes already acquires card->lock inside its function
body, move this out to the callsites of fw_destroy_nodes.
Also add a comment to indicate which locking is necessary when calling
fw_destroy_nodes.
Cc: <stable@vger.kernel.org>
Signed-off-by: Niels Dossche <dossche.niels@gmail.com>
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Link: https://lore.kernel.org/r/20220409041243.603210-4-o-takashi@sakamocchi.jp
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 9423973869bd4632ffe669f950510c49296656e0 upstream.
When list_for_each_entry() completes the iteration over the whole list
without breaking the loop, the iterator value will be a bogus pointer
computed based on the head element.
While it is safe to use the pointer to determine if it was computed
based on the head element, either with list_entry_is_head() or
&pos->member == head, using the iterator variable after the loop should
be avoided.
In preparation to limit the scope of a list iterator to the list
traversal loop, use a dedicated pointer to point to the found element [1].
Link: https://lore.kernel.org/all/CAHk-=wgRr_D8CB-D9Kg-c=EHreAsk5SqXPwr9Y7k9sA6cWXJ6w@mail.gmail.com/ [1]
Cc: <stable@vger.kernel.org>
Signed-off-by: Jakob Koschel <jakobkoschel@gmail.com>
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Link: https://lore.kernel.org/r/20220409041243.603210-3-o-takashi@sakamocchi.jp
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit b7c81f80246fac44077166f3e07103affe6db8ff upstream.
&e->event and e point to the same address, and &e->event could
be freed in queue_event. So there is a potential uaf issue if
we dereference e after calling queue_event(). Fix this by adding
a temporary variable to maintain e->client in advance, this can
avoid the potential uaf issue.
Cc: <stable@vger.kernel.org>
Signed-off-by: Chengfeng Ye <cyeaa@connect.ust.hk>
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Link: https://lore.kernel.org/r/20220409041243.603210-2-o-takashi@sakamocchi.jp
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit ff9166c623704337bd6fe66fce2838d9768a6634 upstream.
n_gsm is based on the 3GPP 07.010 and its newer version is the 3GPP 27.010.
See https://portal.3gpp.org/desktopmodules/Specifications/SpecificationDetails.aspx?specificationId=1516
The changes from 07.010 to 27.010 are non-functional. Therefore, I refer to
the newer 27.010 here. Chapter 5.4.4.2 states that any received unnumbered
acknowledgment (UA) with its poll/final (PF) bit set to 0 shall be
discarded. Currently, all UA frame are handled in the same way regardless
of the PF bit. This does not comply with the standard.
Remove the UA case in gsm_queue() to process only UA frames with PF bit set
to 1 to abide the standard.
Fixes: e1eaea46bb40 ("tty: n_gsm line discipline")
Cc: stable@vger.kernel.org
Signed-off-by: Daniel Starke <daniel.starke@siemens.com>
Link: https://lore.kernel.org/r/20220414094225.4527-20-daniel.starke@siemens.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 398867f59f956985f4c324f173eff7b946e14bd8 upstream.
n_gsm is based on the 3GPP 07.010 and its newer version is the 3GPP 27.010.
See https://portal.3gpp.org/desktopmodules/Specifications/SpecificationDetails.aspx?specificationId=1516
The changes from 07.010 to 27.010 are non-functional. Therefore, I refer to
the newer 27.010 here. Chapter 5.4.6.1 states that each command frame shall
be made up from type, length and value. Looking for example in chapter
5.4.6.3.5 at the description for the encoding of a flow control on command
it becomes obvious, that the type and length field is always present
whereas the value may be zero bytes long. The current implementation omits
the length field if the value is not present. This is wrong.
Correct this by always sending the length in gsm_control_transmit().
So far only the modem status command (MSC) has included a value and encoded
its length directly. Therefore, also change gsmtty_modem_update().
Fixes: e1eaea46bb40 ("tty: n_gsm line discipline")
Cc: stable@vger.kernel.org
Signed-off-by: Daniel Starke <daniel.starke@siemens.com>
Link: https://lore.kernel.org/r/20220414094225.4527-12-daniel.starke@siemens.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit d0bcdffcad5a22f202e3bf37190c0dd8c080ea92 upstream.
n_gsm is based on the 3GPP 07.010 and its newer version is the 3GPP 27.010.
See https://portal.3gpp.org/desktopmodules/Specifications/SpecificationDetails.aspx?specificationId=1516
The changes from 07.010 to 27.010 are non-functional. Therefore, I refer to
the newer 27.010 here. Chapter 5.7.3 states that the valid range for the
maximum number of retransmissions (N2) is from 0 to 255 (both including).
gsm_config() fails to limit this range correctly. Furthermore,
gsm_control_retransmit() handles this number incorrectly by performing
N2 - 1 retransmission attempts. Setting N2 to zero results in more than 255
retransmission attempts.
Fix the range check in gsm_config() and the value handling in
gsm_control_send() and gsm_control_retransmit() to comply with 3GPP 27.010.
Fixes: e1eaea46bb40 ("tty: n_gsm line discipline")
Cc: stable@vger.kernel.org
Signed-off-by: Daniel Starke <daniel.starke@siemens.com>
Link: https://lore.kernel.org/r/20220414094225.4527-11-daniel.starke@siemens.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 17eac652028501df7ea296b1d9b9c134db262b7d upstream.
In gsm_cleanup_mux() the muxer is closed down and all queues are removed.
However, removing the queues is done without explicit control of the
underlying buffers. Flush those before freeing up our queues to ensure
that all outgoing queues are cleared consistently. Otherwise, a new mux
connection establishment attempt may time out while the underlying tty is
still busy sending out the remaining data from the previous connection.
Fixes: e1eaea46bb40 ("tty: n_gsm line discipline")
Cc: stable@vger.kernel.org
Signed-off-by: Daniel Starke <daniel.starke@siemens.com>
Link: https://lore.kernel.org/r/20220414094225.4527-10-daniel.starke@siemens.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 535bf600de75a859698892ee873521a48d289ec1 upstream.
n_gsm is based on the 3GPP 07.010 and its newer version is the 3GPP 27.010.
See https://portal.3gpp.org/desktopmodules/Specifications/SpecificationDetails.aspx?specificationId=1516
The changes from 07.010 to 27.010 are non-functional. Therefore, I refer to
the newer 27.010 here. Chapter 5.7.2 states that the maximum frame size
(N1) refers to the length of the information field (i.e. user payload).
However, 'txframe' stores the whole frame including frame header, checksum
and start/end flags. We also need to consider the byte stuffing overhead.
Define constant for the protocol overhead and adjust the 'txframe' size
calculation accordingly to reserve enough space for a complete mux frame
including byte stuffing for advanced option mode. Note that no byte
stuffing is applied to the start and end flag.
Also use MAX_MTU instead of MAX_MRU as this buffer is used for data
transmission.
Fixes: e1eaea46bb40 ("tty: n_gsm line discipline")
Cc: stable@vger.kernel.org
Signed-off-by: Daniel Starke <daniel.starke@siemens.com>
Link: https://lore.kernel.org/r/20220414094225.4527-8-daniel.starke@siemens.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit a24b4b2f660b7ddf3f484b37600bba382cb28a9d upstream.
The gsm_mux field 'malformed' represents the number of malformed frames
received. However, gsm1_receive() also increases this counter for any out
of frame byte.
Fix this by ignoring out of frame data for the malformed counter.
Fixes: e1eaea46bb40 ("tty: n_gsm line discipline")
Cc: stable@vger.kernel.org
Signed-off-by: Daniel Starke <daniel.starke@siemens.com>
Link: https://lore.kernel.org/r/20220414094225.4527-7-daniel.starke@siemens.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 06d5afd4d640eea67f5623e76cd5fc03359b7f3c upstream.
n_gsm is based on the 3GPP 07.010 and its newer version is the 3GPP 27.010.
See https://portal.3gpp.org/desktopmodules/Specifications/SpecificationDetails.aspx?specificationId=1516
The changes from 07.010 to 27.010 are non-functional. Therefore, I refer to
the newer 27.010 here. Chapter 5.5.2 describes that the signal octet in
convergence layer type 2 can be either one or two bytes. The length is
encoded in the EA bit. This is set 1 for the last byte in the sequence.
gsmtty_modem_update() handles this correctly but gsm_dlci_data_output()
fails to set EA to 1. There is no case in which we encode two signal octets
as there is no case in which we send out a break signal.
Therefore, always set the EA bit to 1 for the signal octet to fix this.
Fixes: e1eaea46bb40 ("tty: n_gsm line discipline")
Cc: stable@vger.kernel.org
Signed-off-by: Daniel Starke <daniel.starke@siemens.com>
Link: https://lore.kernel.org/r/20220414094225.4527-5-daniel.starke@siemens.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit bc6de2878429e85c1f1afaa566f7b5abb2243eef ]
There is a deadlock in rr_close(), which is shown below:
(Thread 1) | (Thread 2)
| rr_open()
rr_close() | add_timer()
spin_lock_irqsave() //(1) | (wait a time)
... | rr_timer()
del_timer_sync() | spin_lock_irqsave() //(2)
(wait timer to stop) | ...
We hold rrpriv->lock in position (1) of thread 1 and
use del_timer_sync() to wait timer to stop, but timer handler
also need rrpriv->lock in position (2) of thread 2.
As a result, rr_close() will block forever.
This patch extracts del_timer_sync() from the protection of
spin_lock_irqsave(), which could let timer handler to obtain
the needed lock.
Signed-off-by: Duoming Zhou <duoming@zju.edu.cn>
Link: https://lore.kernel.org/r/20220417125519.82618-1-duoming@zju.edu.cn
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit af68656d66eda219b7f55ce8313a1da0312c79e1 ]
While handling PCI errors (AER flow) driver tries to
disable NAPI [napi_disable()] after NAPI is deleted
[__netif_napi_del()] which causes unexpected system
hang/crash.
System message log shows the following:
=======================================
[ 3222.537510] EEH: Detected PCI bus error on PHB#384-PE#800000 [ 3222.537511] EEH: This PCI device has failed 2 times in the last hour and will be permanently disabled after 5 failures.
[ 3222.537512] EEH: Notify device drivers to shutdown [ 3222.537513] EEH: Beginning: 'error_detected(IO frozen)'
[ 3222.537514] EEH: PE#800000 (PCI 0384:80:00.0): Invoking
bnx2x->error_detected(IO frozen)
[ 3222.537516] bnx2x: [bnx2x_io_error_detected:14236(eth14)]IO error detected [ 3222.537650] EEH: PE#800000 (PCI 0384:80:00.0): bnx2x driver reports:
'need reset'
[ 3222.537651] EEH: PE#800000 (PCI 0384:80:00.1): Invoking
bnx2x->error_detected(IO frozen)
[ 3222.537651] bnx2x: [bnx2x_io_error_detected:14236(eth13)]IO error detected [ 3222.537729] EEH: PE#800000 (PCI 0384:80:00.1): bnx2x driver reports:
'need reset'
[ 3222.537729] EEH: Finished:'error_detected(IO frozen)' with aggregate recovery state:'need reset'
[ 3222.537890] EEH: Collect temporary log [ 3222.583481] EEH: of node=0384:80:00.0 [ 3222.583519] EEH: PCI device/vendor: 168e14e4 [ 3222.583557] EEH: PCI cmd/status register: 00100140 [ 3222.583557] EEH: PCI-E capabilities and status follow:
[ 3222.583744] EEH: PCI-E 00: 00020010 012c8da2 00095d5e 00455c82 [ 3222.583892] EEH: PCI-E 10: 10820000 00000000 00000000 00000000 [ 3222.583893] EEH: PCI-E 20: 00000000 [ 3222.583893] EEH: PCI-E AER capability register set follows:
[ 3222.584079] EEH: PCI-E AER 00: 13c10001 00000000 00000000 00062030 [ 3222.584230] EEH: PCI-E AER 10: 00002000 000031c0 000001e0 00000000 [ 3222.584378] EEH: PCI-E AER 20: 00000000 00000000 00000000 00000000 [ 3222.584416] EEH: PCI-E AER 30: 00000000 00000000 [ 3222.584416] EEH: of node=0384:80:00.1 [ 3222.584454] EEH: PCI device/vendor: 168e14e4 [ 3222.584491] EEH: PCI cmd/status register: 00100140 [ 3222.584492] EEH: PCI-E capabilities and status follow:
[ 3222.584677] EEH: PCI-E 00: 00020010 012c8da2 00095d5e 00455c82 [ 3222.584825] EEH: PCI-E 10: 10820000 00000000 00000000 00000000 [ 3222.584826] EEH: PCI-E 20: 00000000 [ 3222.584826] EEH: PCI-E AER capability register set follows:
[ 3222.585011] EEH: PCI-E AER 00: 13c10001 00000000 00000000 00062030 [ 3222.585160] EEH: PCI-E AER 10: 00002000 000031c0 000001e0 00000000 [ 3222.585309] EEH: PCI-E AER 20: 00000000 00000000 00000000 00000000 [ 3222.585347] EEH: PCI-E AER 30: 00000000 00000000 [ 3222.586872] RTAS: event: 5, Type: Platform Error (224), Severity: 2 [ 3222.586873] EEH: Reset without hotplug activity [ 3224.762767] EEH: Beginning: 'slot_reset'
[ 3224.762770] EEH: PE#800000 (PCI 0384:80:00.0): Invoking
bnx2x->slot_reset()
[ 3224.762771] bnx2x: [bnx2x_io_slot_reset:14271(eth14)]IO slot reset initializing...
[ 3224.762887] bnx2x 0384:80:00.0: enabling device (0140 -> 0142) [ 3224.768157] bnx2x: [bnx2x_io_slot_reset:14287(eth14)]IO slot reset
--> driver unload
Uninterruptible tasks
=====================
crash> ps | grep UN
213 2 11 c000000004c89e00 UN 0.0 0 0 [eehd]
215 2 0 c000000004c80000 UN 0.0 0 0
[kworker/0:2]
2196 1 28 c000000004504f00 UN 0.1 15936 11136 wickedd
4287 1 9 c00000020d076800 UN 0.0 4032 3008 agetty
4289 1 20 c00000020d056680 UN 0.0 7232 3840 agetty
32423 2 26 c00000020038c580 UN 0.0 0 0
[kworker/26:3]
32871 4241 27 c0000002609ddd00 UN 0.1 18624 11648 sshd
32920 10130 16 c00000027284a100 UN 0.1 48512 12608 sendmail
33092 32987 0 c000000205218b00 UN 0.1 48512 12608 sendmail
33154 4567 16 c000000260e51780 UN 0.1 48832 12864 pickup
33209 4241 36 c000000270cb6500 UN 0.1 18624 11712 sshd
33473 33283 0 c000000205211480 UN 0.1 48512 12672 sendmail
33531 4241 37 c00000023c902780 UN 0.1 18624 11648 sshd
EEH handler hung while bnx2x sleeping and holding RTNL lock
===========================================================
crash> bt 213
PID: 213 TASK: c000000004c89e00 CPU: 11 COMMAND: "eehd"
#0 [c000000004d477e0] __schedule at c000000000c70808
#1 [c000000004d478b0] schedule at c000000000c70ee0
#2 [c000000004d478e0] schedule_timeout at c000000000c76dec
#3 [c000000004d479c0] msleep at c0000000002120cc
#4 [c000000004d479f0] napi_disable at c000000000a06448
^^^^^^^^^^^^^^^^
#5 [c000000004d47a30] bnx2x_netif_stop at c0080000018dba94 [bnx2x]
#6 [c000000004d47a60] bnx2x_io_slot_reset at c0080000018a551c [bnx2x]
#7 [c000000004d47b20] eeh_report_reset at c00000000004c9bc
#8 [c000000004d47b90] eeh_pe_report at c00000000004d1a8
#9 [c000000004d47c40] eeh_handle_normal_event at c00000000004da64
And the sleeping source code
============================
crash> dis -ls c000000000a06448
FILE: ../net/core/dev.c
LINE: 6702
6697 {
6698 might_sleep();
6699 set_bit(NAPI_STATE_DISABLE, &n->state);
6700
6701 while (test_and_set_bit(NAPI_STATE_SCHED, &n->state))
* 6702 msleep(1);
6703 while (test_and_set_bit(NAPI_STATE_NPSVC, &n->state))
6704 msleep(1);
6705
6706 hrtimer_cancel(&n->timer);
6707
6708 clear_bit(NAPI_STATE_DISABLE, &n->state);
6709 }
EEH calls into bnx2x twice based on the system log above, first through
bnx2x_io_error_detected() and then bnx2x_io_slot_reset(), and executes
the following call chains:
bnx2x_io_error_detected()
+-> bnx2x_eeh_nic_unload()
+-> bnx2x_del_all_napi()
+-> __netif_napi_del()
bnx2x_io_slot_reset()
+-> bnx2x_netif_stop()
+-> bnx2x_napi_disable()
+->napi_disable()
Fix this by correcting the sequence of NAPI APIs usage,
that is delete the NAPI after disabling it.
Fixes: 7fa6f34081f1 ("bnx2x: AER revised")
Reported-by: David Christensen <drc@linux.vnet.ibm.com>
Tested-by: David Christensen <drc@linux.vnet.ibm.com>
Signed-off-by: Manish Chopra <manishc@marvell.com>
Signed-off-by: Ariel Elior <aelior@marvell.com>
Link: https://lore.kernel.org/r/20220426153913.6966-1-manishc@marvell.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit f58ca215cda1975f77b2b762903684a3c101bec9 ]
It will cause null-ptr-deref if platform_get_resource() returns NULL,
we need check the return value.
Fixes: 7a6fca879f59 ("clk: sunxi: Add driver for A80 MMC config clocks/resets")
Signed-off-by: Yang Yingliang <yangyingliang@huawei.com>
Reviewed-by: Samuel Holland <samuel@sholland.org>
Signed-off-by: Jernej Skrabec <jernej.skrabec@gmail.com>
Link: https://lore.kernel.org/r/20220421134308.2885094-1-yangyingliang@huawei.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit fff8c10368e64e7f8960f149375c12ca5f3b30af ]
This code is really spurious.
It always returns an ERR_PTR, even when err is known to be 0 and calls
put_device() after a successful device_register() call.
It is likely that the return statement in the normal path is missing.
Add 'return rdev;' to fix it.
Fixes: d787dcdb9c8f ("bus: sunxi-rsb: Add driver for Allwinner Reduced Serial Bus")
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Reviewed-by: Samuel Holland <samuel@sholland.org>
Tested-by: Samuel Holland <samuel@sholland.org>
Signed-off-by: Jernej Skrabec <jernej.skrabec@gmail.com>
Link: https://lore.kernel.org/r/ef2b9576350bba4c8e05e669e9535e9e2a415763.1650551719.git.christophe.jaillet@wanadoo.fr
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 0c9843a74a85224a89daa81fa66891dae2f930e1 ]
The irq_of_parse_and_map() function returns 0 on failure, and does not
return an negative value.
Fixes: cefc03e5995e ("pinctrl: Add Pistachio SoC pin control driver")
Reported-by: Zeal Robot <zealci@zte.com.cn>
Signed-off-by: Lv Ruyi <lv.ruyi@zte.com.cn>
Link: https://lore.kernel.org/r/20220424031430.3170759-1-lv.ruyi@zte.com.cn
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 084c16ab423a8890121b902b405823bfec5b4365 ]
wait_for_completion_timeout() returns unsigned long not int.
It returns 0 if timed out, and positive if completed.
The check for <= 0 is ambiguous and should be == 0 here
indicating timeout which is the only error case.
Fixes: 83738d87e3a0 ("mtd: sh_flctl: Add DMA capabilty")
Signed-off-by: Miaoqian Lin <linmq006@gmail.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20220412083435.29254-1-linmq006@gmail.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 5c8402c4db45dd55c2c93c8d730f5dfa7c78a702 ]
The actions of of_find_i2c_device_by_node() in probe function should be
reversed in error paths by putting the reference to obtained device.
Fixes: bcff4cba41bc ("PHY: Exynos: Add Exynos5250 SATA PHY driver")
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Reviewed-by: Alim Akhtar <alim.akhtar@samsung.com>
Link: https://lore.kernel.org/r/20220407091857.230386-2-krzysztof.kozlowski@linaro.org
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 388ec8f079f2f20d5cd183c3bc6f33cbc3ffd3ef ]
The device_node pointer is returned by of_parse_phandle() with refcount
incremented. We should use of_node_put() on it when done.
Fixes: bcff4cba41bc ("PHY: Exynos: Add Exynos5250 SATA PHY driver")
Signed-off-by: Miaoqian Lin <linmq006@gmail.com>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Link: https://lore.kernel.org/r/20220407091857.230386-1-krzysztof.kozlowski@linaro.org
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
commit 637674fa40059cddcc3ad2212728965072f62ea3 upstream.
The EndRun PTP/1588 dual serial port device is based on the Oxford
Semiconductor OXPCIe952 UART device with the PCI vendor:device ID set
for EndRun Technologies and is therefore driven by a fixed 62.5MHz clock
input derived from the 100MHz PCI Express clock. The clock rate is
divided by the oversampling rate of 16 as it is supplied to the baud
rate generator, yielding the baud base of 3906250.
Replace the incorrect baud base of 4000000 with the right value of
3906250 then, complementing commit 6cbe45d8ac93 ("serial: 8250: Correct
the clock for OxSemi PCIe devices").
Signed-off-by: Maciej W. Rozycki <macro@orcam.me.uk>
Cc: stable <stable@kernel.org>
Fixes: 1bc8cde46a159 ("8250_pci: Added driver for Endrun Technologies PTP PCIe card.")
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Link: https://lore.kernel.org/r/alpine.DEB.2.21.2204181515270.9383@angie.orcam.me.uk
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 6e6eebdf5e2455f089ccd000754a0deaeb79af82 upstream.
Sticky MCR bits are lost in console restoration if console suspending
has been disabled. This currently affects the AFE bit, which works in
combination with RTS which we set, so we want to make sure the UART
retains control of its FIFO where previously requested. Also specific
drivers may need other bits in the future.
Signed-off-by: Maciej W. Rozycki <macro@orcam.me.uk>
Fixes: 4516d50aabed ("serial: 8250: Use canary to restart console after suspend")
Cc: stable@vger.kernel.org # v4.0+
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Link: https://lore.kernel.org/r/alpine.DEB.2.21.2204181518490.9383@angie.orcam.me.uk
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit bf95c4d4630c7a2c16e7b424fdea5177d9ce0864 upstream.
If any function like UVC is deactivating gadget as part of composition
switch which results in not calling pullup enablement, it is not getting
enabled after switch to new composition due to this deactivation flag
not cleared. This results in USB enumeration not happening after switch
to new USB composition. Hence clear deactivation flag inside gadget
structure in configfs_composite_unbind() before switch to new USB
composition.
Signed-off-by: Vijayavardhan Vennapusa <vvreddy@codeaurora.org>
Signed-off-by: Dan Vacura <w36195@motorola.com>
Cc: stable <stable@kernel.org>
Link: https://lore.kernel.org/r/20220413211038.72797-1-w36195@motorola.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 71d471e3faf90c9674cadc7605ac719e82cb7fac upstream.
During the uvcg_video_pump() process, if an error occurs and
uvcg_queue_cancel() is called, the buffer queue will be cleared out, but
the current marker (queue->buf_used) of the active buffer (no longer
active) is not reset. On the next iteration of uvcg_video_pump() the
stale buf_used count will be used and the logic of min((unsigned
int)len, buf->bytesused - queue->buf_used) may incorrectly calculate a
nbytes size, causing an invalid memory access.
[80802.185460][ T315] configfs-gadget gadget: uvc: VS request completed
with status -18.
[80802.185519][ T315] configfs-gadget gadget: uvc: VS request completed
with status -18.
...
uvcg_queue_cancel() is called and the queue is cleared out, but the
marker queue->buf_used is not reset.
...
[80802.262328][ T8682] Unable to handle kernel paging request at virtual
address ffffffc03af9f000
...
...
[80802.263138][ T8682] Call trace:
[80802.263146][ T8682] __memcpy+0x12c/0x180
[80802.263155][ T8682] uvcg_video_pump+0xcc/0x1e0
[80802.263165][ T8682] process_one_work+0x2cc/0x568
[80802.263173][ T8682] worker_thread+0x28c/0x518
[80802.263181][ T8682] kthread+0x160/0x170
[80802.263188][ T8682] ret_from_fork+0x10/0x18
[80802.263198][ T8682] Code: a8c12829 a88130cb a8c130
Fixes: d692522577c0 ("usb: gadget/uvc: Port UVC webcam gadget to use videobuf2 framework")
Cc: <stable@vger.kernel.org>
Signed-off-by: Dan Vacura <w36195@motorola.com>
Link: https://lore.kernel.org/r/20220331184024.23918-1-w36195@motorola.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 0a96fa640dc928da9eaa46a22c46521b037b78ad upstream.
usb_put_dev shouldn't be called when uss720_probe succeeds because of
priv->usbdev. At the same time, priv->usbdev shouldn't be set to NULL
before destroy_priv in uss720_disconnect because usb_put_dev is in
destroy_priv.
Fix this by moving priv->usbdev = NULL after usb_put_dev.
Fixes: dcb4b8ad6a44 ("misc/uss720: fix memory leak in uss720_probe")
Cc: stable <stable@kernel.org>
Reviewed-by: Dongliang Mu <mudongliangabcd@gmail.com>
Signed-off-by: Hangyu Hua <hbh25y@gmail.com>
Link: https://lore.kernel.org/r/20220407024001.11761-1-hbh25y@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 3a26787dacf04257a68b16315c984eb2c340bc5e upstream.
When the driver fails to enable the regulator 'vid', we will get the
following splat:
[ 79.955610] WARNING: CPU: 5 PID: 441 at drivers/regulator/core.c:2257 _regulator_put+0x3ec/0x4e0
[ 79.959641] RIP: 0010:_regulator_put+0x3ec/0x4e0
[ 79.967570] Call Trace:
[ 79.967773] <TASK>
[ 79.967951] regulator_put+0x1f/0x30
[ 79.968254] devres_release_group+0x319/0x3d0
[ 79.968608] i2c_device_probe+0x766/0x940
Fix this by disabling the 'vdd' regulator when failing to enable 'vid'
regulator.
Signed-off-by: Zheyu Ma <zheyuma97@gmail.com>
Link: https://lore.kernel.org/r/20220409034849.3717231-2-zheyuma97@gmail.com
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 89a01cd688d3c0ac983ef0b0e5f40018ab768317 upstream.
read_raw should return the un-scaled value.
Fixes: 5e06bdfb46e8b ("staging:iio:dac:ad5446: Return cached value for 'raw' attribute")
Signed-off-by: Michael Hennerich <michael.hennerich@analog.com>
Reviewed-by: Nuno Sá <nuno.sa@analog.com>
Link: https://lore.kernel.org/r/20220406105620.1171340-1-michael.hennerich@analog.com
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit b55b38f7cc12da3b9ef36e7a3b7f8f96737df4d5 upstream.
The third call to `fwnode_property_read_u32` did not record
the return value, resulting in `channel_offstate` possibly
being assigned the wrong value.
Fixes: 56ca9db862bf ("iio: dac: Add support for the AD5592R/AD5593R ADCs/DACs")
Signed-off-by: Zizhuang Deng <sunsetdzz@gmail.com>
Link: https://lore.kernel.org/r/20220310125450.4164164-1-sunsetdzz@gmail.com
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit dc92944a014cd6a6f6c94299aaa36164dd2c238a upstream.
While rebooting, XHCI controller and its bus device will be shut down
in order by .shutdown callback. Stopping roothubs polling in
xhci_shutdown() can prevent XHCI driver from accessing port status
after its bus device shutdown.
Take PCIe XHCI controller as example, if XHCI driver doesn't stop roothubs
polling, XHCI driver may access PCIe BAR register for port status after
parent PCIe root port driver is shutdown and cause PCIe bus error.
[check shared hcd exist before stopping its roothub polling -Mathias]
Cc: stable@vger.kernel.org
Signed-off-by: Henry Lin <henryl@nvidia.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20220408134823.2527272-3-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit f32c5a0423400e01f4d7c607949fa3a1f006e8fa upstream.
Add support for the following Telit FN980 and FN990 compositions:
0x1057: tty, adb, rmnet, tty, tty, tty, tty, tty
0x1058: tty, adb, tty, tty, tty, tty, tty
0x1075: adb, tty
Signed-off-by: Daniele Palmas <dnlplm@gmail.com>
Link: https://lore.kernel.org/r/20220406141408.580669-1-dnlplm@gmail.com
Cc: stable@vger.kernel.org
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit b4a64ed6e7b857317070fcb9d87ff5d4a73be3e8 upstream.
Add support for Cinterion device MV32-WA/MV32-WB. MV32-WA PID is
0x00F1, and MV32-WB PID is 0x00F2.
Test evidence as below:
T: Bus=04 Lev=01 Prnt=01 Port=01 Cnt=01 Dev#= 4 Spd=5000 MxCh= 0
D: Ver= 3.20 Cls=ef(misc ) Sub=02 Prot=01 MxPS= 9 #Cfgs= 1
P: Vendor=1e2d ProdID=00f1 Rev=05.04
S: Manufacturer=Cinterion
S: Product=Cinterion PID 0x00F1 USB Mobile Broadband
S: SerialNumber=78ada8c4
C: #Ifs= 6 Cfg#= 1 Atr=a0 MxPwr=896mA
I: If#=0x0 Alt= 0 #EPs= 1 Cls=02(commc) Sub=0e Prot=00 Driver=cdc_mbim
I: If#=0x1 Alt= 1 #EPs= 2 Cls=0a(data ) Sub=00 Prot=02 Driver=cdc_mbim
I: If#=0x2 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=ff Prot=40 Driver=option
I: If#=0x3 Alt= 0 #EPs= 1 Cls=ff(vend.) Sub=ff Prot=ff Driver=(none)
I: If#=0x4 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=ff Prot=60 Driver=option
I: If#=0x5 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=30 Driver=option
T: Bus=04 Lev=01 Prnt=01 Port=01 Cnt=01 Dev#= 3 Spd=5000 MxCh= 0
D: Ver= 3.20 Cls=ef(misc ) Sub=02 Prot=01 MxPS= 9 #Cfgs= 1
P: Vendor=1e2d ProdID=00f2 Rev=05.04
S: Manufacturer=Cinterion
S: Product=Cinterion PID 0x00F2 USB Mobile Broadband
S: SerialNumber=cdd06a78
C: #Ifs= 6 Cfg#= 1 Atr=a0 MxPwr=896mA
I: If#=0x0 Alt= 0 #EPs= 1 Cls=02(commc) Sub=0e Prot=00 Driver=cdc_mbim
I: If#=0x1 Alt= 1 #EPs= 2 Cls=0a(data ) Sub=00 Prot=02 Driver=cdc_mbim
I: If#=0x2 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=ff Prot=40 Driver=option
I: If#=0x3 Alt= 0 #EPs= 1 Cls=ff(vend.) Sub=ff Prot=ff Driver=(none)
I: If#=0x4 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=ff Prot=60 Driver=option
I: If#=0x5 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=30 Driver=option
Interface 0&1: MBIM, 2:Modem, 3: GNSS, 4: NMEA, 5: Diag
GNSS port don't use serial driver.
Signed-off-by: Slark Xiao <slark_xiao@163.com>
Link: https://lore.kernel.org/r/20220414074434.5699-1-slark_xiao@163.com
Cc: stable@vger.kernel.org
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 35a923a0b329c343e9e81d79518e2937eba06fcd upstream.
Wireless reading of water and heat meters using 868 MHz wM-Bus mode C1.
The two different product IDs allow detection of dongle antenna
solution:
- Internal antenna
- External antenna using SMA connector
https://www.kamstrup.com/en-en/water-solutions/water-meter-reading/usb-meter-reader
Signed-off-by: Bruno Thomsen <bruno.thomsen@gmail.com>
Link: https://lore.kernel.org/r/20220414081202.5591-1-bruno.thomsen@gmail.com
Cc: stable@vger.kernel.org
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit e23e50e7acc8d8f16498e9c129db33e6a00e80eb upstream.
The sizeof(struct whitehat_dr_info) can be 4 bytes under CONFIG_AEABI=n
due to "-mabi=apcs-gnu", even though it has a single u8:
whiteheat_private {
__u8 mcr; /* 0 1 */
/* size: 4, cachelines: 1, members: 1 */
/* padding: 3 */
/* last cacheline: 4 bytes */
};
The result is technically harmless, as both the source and the
destinations are currently the same allocation size (4 bytes) and don't
use their padding, but if anything were to ever be added after the
"mcr" member in "struct whiteheat_private", it would be overwritten. The
structs both have a single u8 "mcr" member, but are 4 bytes in padded
size. The memcpy() destination was explicitly targeting the u8 member
(size 1) with the length of the whole structure (size 4), triggering
the memcpy buffer overflow warning:
In file included from include/linux/string.h:253,
from include/linux/bitmap.h:11,
from include/linux/cpumask.h:12,
from include/linux/smp.h:13,
from include/linux/lockdep.h:14,
from include/linux/spinlock.h:62,
from include/linux/mmzone.h:8,
from include/linux/gfp.h:6,
from include/linux/slab.h:15,
from drivers/usb/serial/whiteheat.c:17:
In function 'fortify_memcpy_chk',
inlined from 'firm_send_command' at drivers/usb/serial/whiteheat.c:587:4:
include/linux/fortify-string.h:328:25: warning: call to '__write_overflow_field' declared with attribute warning: detected write beyond size of field (1st parameter); maybe use struct_group()? [-Wattribute-warning]
328 | __write_overflow_field(p_size_field, size);
| ^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
Instead, just assign the one byte directly.
Reported-by: kernel test robot <lkp@intel.com>
Link: https://lore.kernel.org/lkml/202204142318.vDqjjSFn-lkp@intel.com
Cc: stable@vger.kernel.org
Signed-off-by: Kees Cook <keescook@chromium.org>
Link: https://lore.kernel.org/r/20220421001234.2421107-1-keescook@chromium.org
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit ec547af8a9ea6441864bad34172676b5652ceb96 upstream.
This has been reported to stall if queried
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Oliver Neukum <oneukum@suse.com>
Link: https://lore.kernel.org/r/20220414123152.1700-1-oneukum@suse.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 2a7ccf6bb6f147f64c025ad68f4255d8e1e0ce6d upstream.
This device is reported to stall when enummerated.
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Oliver Neukum <oneukum@suse.com>
Link: https://lore.kernel.org/r/20220414110209.30924-1-oneukum@suse.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
In commit 9ea9b9c48387 ("remove the lightnvm subsystem") the lightnvm
subsystem was removed as there is no hardware in the wild for it, and
the code is known to have problems. This should also be disabled for
older LTS kernels as well to prevent anyone from accidentally using it.
Cc: Christoph Hellwig <hch@lst.de>
Cc: Matias Bjørling <mb@lightnvm.io>
Cc: Javier González <javier@javigon.com>
Cc: Jens Axboe <axboe@kernel.dk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
fixed-link"
This reverts commit edba120f094394454f5b9511d04abd7e8c2c31ee which is
commit a6aaa00324240967272b451bfa772547bd576ee6 upstream.
Pavel reports that it causes boot issues, so revert it for now.
Link: https://lore.kernel.org/r/20220429074341.GB1423@amd
Reported-by: Pavel Machek <pavel@denx.de>
Cc: Dinh Nguyen <dinguyen@kernel.org>
Cc: David S. Miller <davem@davemloft.net>
Cc: Sasha Levin <sashal@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 233087ca063686964a53c829d547c7571e3f67bf upstream.
Minh Yuan reported a concurrency use-after-free issue in the floppy code
between raw_cmd_ioctl and seek_interrupt.
[ It turns out this has been around, and that others have reported the
KASAN splats over the years, but Minh Yuan had a reproducer for it and
so gets primary credit for reporting it for this fix - Linus ]
The problem is, this driver tends to break very easily and nowadays,
nobody is expected to use FDRAWCMD anyway since it was used to
manipulate non-standard formats. The risk of breaking the driver is
higher than the risk presented by this race, and accessing the device
requires privileges anyway.
Let's just add a config option to completely disable this ioctl and
leave it disabled by default. Distros shouldn't use it, and only those
running on antique hardware might need to enable it.
Link: https://lore.kernel.org/all/000000000000b71cdd05d703f6bf@google.com/
Link: https://lore.kernel.org/lkml/CAKcFiNC=MfYVW-Jt9A3=FPJpTwCD2PL_ULNCpsCVE5s8ZeBQgQ@mail.gmail.com
Link: https://lore.kernel.org/all/CAEAjamu1FRhz6StCe_55XY5s389ZP_xmCF69k987En+1z53=eg@mail.gmail.com
Reported-by: Minh Yuan <yuanmingbuaa@gmail.com>
Reported-by: syzbot+8e8958586909d62b6840@syzkaller.appspotmail.com
Reported-by: cruise k <cruise4k@gmail.com>
Reported-by: Kyungtae Kim <kt0755@gmail.com>
Suggested-by: Linus Torvalds <torvalds@linuxfoundation.org>
Tested-by: Denis Efremov <efremov@linux.com>
Signed-off-by: Willy Tarreau <w@1wt.eu>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 04ebaa1cfddae5f240cc7404f009133bb0389a47 upstream.
When we decode the latency and the max_latency, u16 value may not fit
the required size and could lead to the wrong LTR representation.
Scaling is represented as:
scale 0 - 1 (2^(5*0)) = 2^0
scale 1 - 32 (2^(5 *1))= 2^5
scale 2 - 1024 (2^(5 *2)) =2^10
scale 3 - 32768 (2^(5 *3)) =2^15
scale 4 - 1048576 (2^(5 *4)) = 2^20
scale 5 - 33554432 (2^(5 *4)) = 2^25
scale 4 and scale 5 required 20 and 25 bits respectively.
scale 6 reserved.
Replace the u16 type with the u32 type and allow corrected LTR
representation.
Cc: stable@vger.kernel.org
Fixes: 44a13a5d99c7 ("e1000e: Fix the max snoop/no-snoop latency for 10M")
Reported-by: James Hutchinson <jahutchinson99@googlemail.com>
Link: https://bugzilla.kernel.org/show_bug.cgi?id=215689
Suggested-by: Dima Ruinskiy <dima.ruinskiy@intel.com>
Signed-off-by: Sasha Neftin <sasha.neftin@intel.com>
Tested-by: Naama Meir <naamax.meir@linux.intel.com>
Tested-by: James Hutchinson <jahutchinson99@googlemail.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 206680c4e46b62fd8909385e0874a36952595b85 upstream.
The bug is here:
__func__, desc, &desc->tx_dma_desc.phys, ret, cookie, residue);
The list iterator 'desc' will point to a bogus position containing
HEAD if the list is empty or no element is found. To avoid dev_dbg()
prints a invalid address, use a new variable 'iter' as the list
iterator, while use the origin variable 'desc' as a dedicated
pointer to point to the found element.
Cc: stable@vger.kernel.org
Fixes: 82e2424635f4c ("dmaengine: xdmac: fix print warning on dma_addr_t variable")
Signed-off-by: Xiaomeng Tong <xiam0nd.tong@gmail.com>
Link: https://lore.kernel.org/r/20220327061154.4867-1-xiam0nd.tong@gmail.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
