| Age | Commit message (Collapse) | Author |
|---|
|
Disable ALDPS and EEE to avoid the possible failure when setting the PHY.
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Remove r8153_enable_eee().
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Move the PHY relative settings together to hw_phy_cfg().
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Move enabling PHY to init(), otherwise some other settings may fail.
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Move the following functions forward.
r8152_mmd_indirect()
r8152_mmd_read()
r8152_mmd_write()
r8152_eee_en()
r8152b_enable_eee()
r8153_eee_en()
r8153_enable_eee()
r8152b_enable_fc()
r8153_aldps_en()
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
We were missing check for 25G and 100G while checking port speed,
which lead to less number of queues getting allocated for 25G & 100G
adapters and leading to low throughput. Adding the missing check for
both NIC and vNIC driver.
Also fixes port advertisement for 25G and 100G in ethtool output.
Signed-off-by: Hariprasad Shenai <hariprasad@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/mkl/linux-can
Marc Kleine-Budde says:
====================
pull-request: can 2016-09-19
this is a pull request of one patch for the upcoming linux-4.8 release.
The patch by Fabio Estevam fixes the pm handling in the flexcan driver.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Since the device hierarchy domain was added by commit c98c1822ee13
("irqchip/mips-gic: Add device hierarchy domain"), GIC local interrupts
have been broken.
Users attempting to setup a per-cpu local IRQ, for example the GIC timer
clock events code in drivers/clocksource/mips-gic-timer.c, the
setup_percpu_irq function would refuse with -EINVAL because the GIC
irqchip driver never called irq_set_percpu_devid so the
IRQ_PER_CPU_DEVID flag was never set for the IRQ. This happens because
irq_set_percpu_devid was being called from the gic_irq_domain_map
function which is no longer called.
Doing only that runs into further problems because gic_dev_domain_alloc
set the struct irq_chip for all interrupts, local or shared, to
gic_level_irq_controller despite that only being suitable for shared
interrupts. The typical outcome of this is that gic_level_irq_controller
callback functions are called for local interrupts, and then hwirq
number calculations overflow & the driver ends up attempting to access
some invalid register with an address calculated from an invalid hwirq
number. Best case scenario is that this then leads to a bus error. This
is fixed by abstracting the setup of the hwirq & chip to a new function
gic_setup_dev_chip which is used by both the root GIC IRQ domain & the
device domain.
Finally, decoding local interrupts failed because gic_dev_domain_alloc
only called irq_domain_alloc_irqs_parent for shared interrupts. Local
ones were therefore never associated with hwirqs in the root GIC IRQ
domain and the virq in gic_handle_local_int would always be 0. This is
fixed by calling irq_domain_alloc_irqs_parent unconditionally & having
gic_irq_domain_alloc handle both local & shared interrupts, which is
easy due to the aforementioned abstraction of chip setup into
gic_setup_dev_chip.
This fixes use of the MIPS GIC timer for clock events, which has been
broken since c98c1822ee13 ("irqchip/mips-gic: Add device hierarchy
domain") but hadn't been noticed due to a silent fallback to the MIPS
coprocessor 0 count/compare clock events device.
Fixes: c98c1822ee13 ("irqchip/mips-gic: Add device hierarchy domain")
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Cc: linux-mips@linux-mips.org
Cc: Jason Cooper <jason@lakedaemon.net>
Cc: Qais Yousef <qsyousef@gmail.com>
Cc: stable@vger.kernel.org
Cc: Marc Zyngier <marc.zyngier@arm.com>
Link: http://lkml.kernel.org/r/20160913165335.31389-1-paul.burton@imgtec.com
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
|
|
Commit fe56b9e6a8d95 ("qed: Add module with basic common support")
has introduced a stack corruption during probe, where filling a
local struct with data to be sent to management firmware is incorrectly
filled; The data is written outside of the struct and corrupts
the stack.
Changes from v1:
----------------
- Correct the value written [Caught by David Laight]
Fixes: fe56b9e6a8d95 ("qed: Add module with basic common support")
Signed-off-by: Yuval Mintz <Yuval.Mintz@caviumnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
E-switch mode changes involve creating HW tables, potentially allocating
netdevices, etc, and things can fail. Add an attempt to rollback to the
existing mode when changing to the new mode fails. Only if rollback fails,
getting proper SRIOV functionality requires module unload or sriov
disablement/enablement.
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When enablement of the SRIOV e-switch in certain mode (switchdev or legacy)
fails, we must set the mode to none. Otherwise, we'll run into double free
based crashes when further attempting to deal with the e-switch (such
as when disabling sriov or unloading the driver).
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The FW command output length should be only the length of struct
mlx5_cmd_fc_bulk out field. Failing to do so will cause the memcpy
call which is invoked later in the driver to write over wrong memory
address and corrupt kernel memory which results in random crashes.
This bug was found using the kernel address sanitizer (kasan).
Fixes: a351a1b03bf1 ('net/mlx5: Introduce bulk reading of flow counters')
Signed-off-by: Roi Dayan <roid@mellanox.com>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
gic_raise_softirq() walks the list of cpus using for_each_cpu(), it calls
gic_compute_target_list() which advances the iterator by the number of
CPUs in the cluster.
If gic_compute_target_list() reaches the last CPU it leaves the iterator
pointing at the last CPU. This means the next time round the for_each_cpu()
loop cpumask_next() will be called with an invalid CPU.
This triggers a warning when built with CONFIG_DEBUG_PER_CPU_MAPS:
[ 3.077738] GICv3: CPU1: found redistributor 1 region 0:0x000000002f120000
[ 3.077943] CPU1: Booted secondary processor [410fd0f0]
[ 3.078542] ------------[ cut here ]------------
[ 3.078746] WARNING: CPU: 1 PID: 0 at ../include/linux/cpumask.h:121 gic_raise_softirq+0x12c/0x170
[ 3.078812] Modules linked in:
[ 3.078869]
[ 3.078930] CPU: 1 PID: 0 Comm: swapper/1 Not tainted 4.8.0-rc5+ #5188
[ 3.078994] Hardware name: Foundation-v8A (DT)
[ 3.079059] task: ffff80087a1a0080 task.stack: ffff80087a19c000
[ 3.079145] PC is at gic_raise_softirq+0x12c/0x170
[ 3.079226] LR is at gic_raise_softirq+0xa4/0x170
[ 3.079296] pc : [<ffff0000083ead24>] lr : [<ffff0000083eac9c>] pstate: 200001c9
[ 3.081139] Call trace:
[ 3.081202] Exception stack(0xffff80087a19fbe0 to 0xffff80087a19fd10)
[ 3.082269] [<ffff0000083ead24>] gic_raise_softirq+0x12c/0x170
[ 3.082354] [<ffff00000808e614>] smp_send_reschedule+0x34/0x40
[ 3.082433] [<ffff0000080e80a0>] resched_curr+0x50/0x88
[ 3.082512] [<ffff0000080e89d0>] check_preempt_curr+0x60/0xd0
[ 3.082593] [<ffff0000080e8a60>] ttwu_do_wakeup+0x20/0xe8
[ 3.082672] [<ffff0000080e8bb8>] ttwu_do_activate+0x90/0xc0
[ 3.082753] [<ffff0000080ea9a4>] try_to_wake_up+0x224/0x370
[ 3.082836] [<ffff0000080eabc8>] default_wake_function+0x10/0x18
[ 3.082920] [<ffff000008103134>] __wake_up_common+0x5c/0xa0
[ 3.083003] [<ffff0000081031f4>] __wake_up_locked+0x14/0x20
[ 3.083086] [<ffff000008103f80>] complete+0x40/0x60
[ 3.083168] [<ffff00000808df7c>] secondary_start_kernel+0x15c/0x1d0
[ 3.083240] [<00000000808911a4>] 0x808911a4
[ 3.113401] Detected PIPT I-cache on CPU2
Avoid updating the iterator if the next call to cpumask_next() would
cause the for_each_cpu() loop to exit.
There is no change to gic_raise_softirq()'s behaviour, (cpumask_next()s
eventual call to _find_next_bit() will return early as start >= nbits),
this patch just silences the warning.
Fixes: 021f653791ad ("irqchip: gic-v3: Initial support for GICv3")
Signed-off-by: James Morse <james.morse@arm.com>
Acked-by: Marc Zyngier <marc.zyngier@arm.com>
Cc: linux-arm-kernel@lists.infradead.org
Cc: Jason Cooper <jason@lakedaemon.net>
Link: http://lkml.kernel.org/r/1474306155-3303-1-git-send-email-james.morse@arm.com
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
|
|
Merge fixes from Andrew Morton:
"20 fixes"
* emailed patches from Andrew Morton <akpm@linux-foundation.org>:
rapidio/rio_cm: avoid GFP_KERNEL in atomic context
Revert "ocfs2: bump up o2cb network protocol version"
ocfs2: fix start offset to ocfs2_zero_range_for_truncate()
cgroup: duplicate cgroup reference when cloning sockets
mm: memcontrol: make per-cpu charge cache IRQ-safe for socket accounting
ocfs2: fix double unlock in case retry after free truncate log
fanotify: fix list corruption in fanotify_get_response()
fsnotify: add a way to stop queueing events on group shutdown
ocfs2: fix trans extend while free cached blocks
ocfs2: fix trans extend while flush truncate log
ipc/shm: fix crash if CONFIG_SHMEM is not set
mm: fix the page_swap_info() BUG_ON check
autofs: use dentry flags to block walks during expire
MAINTAINERS: update email for VLYNQ bus entry
mm: avoid endless recursion in dump_page()
mm, thp: fix leaking mapped pte in __collapse_huge_page_swapin()
khugepaged: fix use-after-free in collapse_huge_page()
MAINTAINERS: Maik has moved
ocfs2/dlm: fix race between convert and migration
mem-hotplug: don't clear the only node in new_node_page()
|
|
As reported by Alexey Khoroshilov (https://lkml.org/lkml/2016/9/9/737):
riocm_send_close() is called from rio_cm_shutdown() under
spin_lock_bh(idr_lock), but riocm_send_close() uses a GFP_KERNEL
allocation.
Fix by taking riocm_send_close() outside of spinlock protected code.
[akpm@linux-foundation.org: remove unneeded `if (!list_empty())']
Link: http://lkml.kernel.org/r/20160915175402.10122-1-alexandre.bounine@idt.com
Signed-off-by: Alexandre Bounine <alexandre.bounine@idt.com>
Reported-by: Alexey Khoroshilov <khoroshilov@ispras.ru>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Pull exynos and one stable ABI fix from Dave Airlie:
"One important drm 32/64 ABI fix came in so I'll dequeue what I have,
the rest is just exynos runtime pm fixes, but the net removal of code
seems like a win to me.
I'm going to be sporadic this week due to school holidays, so if
anything urgent turns up, Daniel will take care of it"
* tag 'drm-fixes-for-4.8-rc7' of git://people.freedesktop.org/~airlied/linux:
drm: Only use compat ioctl for addfb2 on X86/IA64
Subject: [PATCH, RESEND] drm: exynos: avoid unused function warning
drm/exynos: g2d: fix system and runtime pm integration
drm/exynos: rotator: fix system and runtime pm integration
drm/exynos: gsc: fix system and runtime pm integration
drm/exynos: fimc: fix system and runtime pm integration
exynos-drm: Fix unsupported GEM memory type error message to be clear
|
|
nd_activate_region() iomaps any hint addresses required when activating
a region. To prevent duplicate mappings it checks the PFN of the hint to
be mapped against the PFNs of the already mapped hints. Unfortunately it
doesn't convert the PFN back into a physical address before passing it
to devm_nvdimm_ioremap(). Instead it applies PHYS_PFN a second time
which ends about as well as you would imagine.
Signed-off-by: Oliver O'Halloran <oohall@gmail.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
|
|
Fix a regression caused by commit 2bc46b3ad3c1 ("[media] media/pci:
convert drivers to use the new vb2_queue dev field").
Three places where q->dev should be set were missed, causing
a WARN.
Fixes: 2bc46b3ad3c1 ("[media] media/pci: convert drivers to use the new vb2_queue dev field").
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Reported-by: Marton Balint <cus@passwd.hu>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
|
|
On a imx6ul-pico board the following error is seen during system suspend:
dpm_run_callback(): platform_pm_resume+0x0/0x54 returns -110
PM: Device 2090000.flexcan failed to resume: error -110
The reason for this suspend error is because when the CAN interface is not
active the clocks are disabled and then flexcan_chip_enable() will
always fail due to a timeout error.
In order to fix this issue, only call flexcan_chip_enable/disable()
when the CAN interface is active.
Based on a patch from Dong Aisheng in the NXP kernel.
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Cc: linux-stable <stable@vger.kernel.org>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
|
commit a894cf6c5a82 ("mtd: nand: mxc: switch to mtd_ooblayout_ops")
introduced a regression accessing the OOB area from the mxc_nand
driver due to an Obiwan error in the mxc_nand_v[12]_ooblayout_free()
functions. They report a bogus oobregion { 64, 7 } which leads to
errors accessing bogus data when reading the oob area.
Prior to the commit the mtd-oobtest module could be run without any
errors. With the offending commit, this test fails with results like:
|Running mtd-oobtest
|
|=================================================
|mtd_oobtest: MTD device: 5
|mtd_oobtest: MTD device size 524288, eraseblock size 131072, page size 2048, count of eraseblocks 4, pages per eraseblock 64, OOB size 64
|mtd_test: scanning for bad eraseblocks
|mtd_test: scanned 4 eraseblocks, 0 are bad
|mtd_oobtest: test 1 of 5
|mtd_oobtest: writing OOBs of whole device
|mtd_oobtest: written up to eraseblock 0
|mtd_oobtest: written 4 eraseblocks
|mtd_oobtest: verifying all eraseblocks
|mtd_oobtest: error @addr[0x0:0x19] 0x9a -> 0x78 diff 0xe2
|mtd_oobtest: error @addr[0x0:0x1a] 0xcc -> 0x0 diff 0xcc
|mtd_oobtest: error @addr[0x0:0x1b] 0xe0 -> 0x85 diff 0x65
|mtd_oobtest: error @addr[0x0:0x1c] 0x60 -> 0x62 diff 0x2
|mtd_oobtest: error @addr[0x0:0x1d] 0x69 -> 0x45 diff 0x2c
|mtd_oobtest: error @addr[0x0:0x1e] 0xcd -> 0xa0 diff 0x6d
|mtd_oobtest: error @addr[0x0:0x1f] 0xf2 -> 0x60 diff 0x92
|mtd_oobtest: error: verify failed at 0x0
[...]
Signed-off-by: Lothar Waßmann <LW@KARO-electronics.de>
Fixes: a894cf6c5a82 ("mtd: nand: mxc: switch to mtd_ooblayout_ops")
Cc: <stable@vger.kernel.org>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
|
|
When mtk_nfc_do_write_page() comparing the sector number,because the
sector number field is at the 12th-bit position of NFI_BYTELEN
register,the masked register should be shifted 12 bits before being
compared.The result of this bug may cause the second subpage has
incomplete ECC parity bytes.
Signed-off-by: RogerCC Lin <rogercc.lin@mediatek.com>
Fixes: 1d6b1e464950 ("mtd: mediatek: driver for MTK Smart Device")
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
|
|
When mtk_ecc_encode() is writing the ECC parity data to the OOB
region,because each register is 4 bytes in length,but the len's unit is
in bytes,the operation in the for loop will cross the ECC's boundary.
Signed-off-by: RogerCC Lin <rogercc.lin@mediatek.com>
Fixes: 1d6b1e464950 ("mtd: mediatek: driver for MTK Smart Device")
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
|
|
Similar to struct drm_update_draw, struct drm_mode_fb_cmd2 has an
unaligned 64 bit field (modifier). This get packed differently between
32 bit and 64 bit modes on architectures that can handle unaligned 64
bit access (X86 and IA64). Other architectures pack the structs the
same and don't need the compat wrapper. Use the same condition for
drm_mode_fb_cmd2 as we use for drm_update_draw.
Note that only the modifier will be packed differently between compat
and non-compat versions.
Reviewed-by: Rob Clark <robdclark@gmail.com>
Signed-off-by: Kristian H. Kristensen <hoegsberg@chromium.org>
[seanpaul added not at bottom of commit msg re: modifier]
Signed-off-by: Sean Paul <seanpaul@chromium.org>
Link: http://patchwork.freedesktop.org/patch/msgid/1473801645-116011-1-git-send-email-hoegsberg@chromium.org
Cc: stable@vger.kernel.org
Signed-off-by: Dave Airlie <airlied@redhat.com>
|
|
MAC devices use the RWKPKTEN and MGKPKTEN bits of the PMT Control/Status
register to generate power management events.
So this patch is to properly set the RWKPKTEN [BIT(2)] inside the
PMT register (needed in case of global unicast).
Reported-by: Aditi SHARMA <aditi-hed.sharma@st.com>
Signed-off-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Cc: Alexandre TORGUE <alexandre.torgue@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When CONFIG_PM is not set, we get a warning about an unused function:
drivers/gpu/drm/exynos/exynos_drm_gsc.c:1219:12: error: 'gsc_clk_ctrl' defined but not used [-Werror=unused-function]
static int gsc_clk_ctrl(struct gsc_context *ctx, bool enable)
^~~~~~~~~~~~
This removes the two #ifdef checks in this file and instead marks the
functions as __maybe_unused, which is a more reliable way of doing the
same, allowing better build coverage and avoiding the warning above.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Inki Dae <inki.dae@samsung.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb
Pull USB fixes from Greg KH:
"Here are two small fixes, and one new device id, for 4.8-rc7
The fixes solve a build error that was reported in your tree for the
blackfin arch, and resolve an issue with a number of broken USB
devices that reported the wrong interval rate. Included here is also
a new device id for the usb-serial driver.
All have been in linux-next with no reported issues"
* tag 'usb-4.8-rc7' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb:
USB: change bInterval default to 10 ms
usb: musb: Fix tusb6010 compile error on blackfin
USB: serial: simple: add support for another Infineon flashloader
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull irq fixes from Thomas Gleixner:
"Two patches from Boris which address a potential deadlock in the atmel
irq chip driver"
* 'irq-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
irqchip/atmel-aic: Fix potential deadlock in ->xlate()
genirq: Provide irq_gc_{lock_irqsave,unlock_irqrestore}() helpers
|
|
Move code from system sleep pm to runtime pm callbacks to ensure proper
driver state preservation when device is under power domain. Then, use
generic helpers for using runtime pm for system sleep pm.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Inki Dae <inki.dae@samsung.com>
|
|
Use generic helpers instead of open-coding usage of runtime pm for system
sleep pm, which was potentially broken for some corner cases.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Inki Dae <inki.dae@samsung.com>
|
|
Use generic helpers instead of open-coding usage of runtime pm for system
sleep pm, which was potentially broken for some corner cases.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Inki Dae <inki.dae@samsung.com>
|
|
Use generic helpers instead of open-coding usage of runtime pm for system
sleep pm, which was potentially broken for some corner cases.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Inki Dae <inki.dae@samsung.com>
|
|
Fix unsupported GEM memory type error message to include the memory type
information.
Signed-off-by: Shuah Khan <shuahkh@osg.samsung.com>
Signed-off-by: Inki Dae <inki.dae@samsung.com>
|
|
Pull MMC fixes from Ulf Hansson:
"MMC host:
- omap/omap_hsmmc: Initialize dma_slave_config to avoid random data
- sdhci-st: Handle interconnect clock"
* tag 'mmc-v4.8-rc6' of git://git.linaro.org/people/ulf.hansson/mmc:
mmc: omap: Initialize dma_slave_config to avoid random data in it's fields
mmc: omap_hsmmc: Initialize dma_slave_config to avoid random data
mmc: sdhci-st: Handle interconnect clock
dt-bindings: mmc: sdhci-st: Mention the discretionary "icn" clock
|
|
Commit 6e7333d "net: add rx_nohandler stat counter" added the new entry
rx_nohandler into struct rtnl_link_stats64. Unfortunately the bna
driver foolishly depends on the structure. It uses part of it for
ethtool statistics and it's not bad but the driver assumes its size
is constant as it defines string for each existing entry. The problem
occurs when the structure is extended because you need to modify bna
driver as well. If not any attempt to retrieve ethtool statistics results
in crash in bnad_get_strings().
The patch changes BNAD_ETHTOOL_STATS_NUM so it counts real number of
strings in the array and also removes rtnl_link_stats64 entries that
are not used in output and are always zero.
Fixes: 6e7333d "net: add rx_nohandler stat counter"
Signed-off-by: Ivan Vecera <ivecera@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Commit ba5ca784 "bna: check for dma mapping errors" added besides other
things a statistic that counts number of DMA buffer mapping failures
per each Rx queue. This counter is not included in ethtool stats output.
Fixes: ba5ca784 "bna: check for dma mapping errors"
Signed-off-by: Ivan Vecera <ivecera@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/iwlwifi/iwlwifi-fixes
* fix to prevent firmware crash when sending off-channel frames
|
|
In case of error during netback_probe() (e.g. an entry missing on the
xenstore) netback_remove() is called on the new device, which will set
the device backend state to XenbusStateClosed by calling
set_backend_state(). However, the backend state wasn't initialized by
netback_probe() at this point, which will cause and invalid transaction
and set_backend_state() to BUG().
Initialize the backend state at the beginning of netback_probe() to
XenbusStateInitialising, and create two new valid state transitions on
set_backend_state(), from XenbusStateInitialising to XenbusStateClosed,
and from XenbusStateInitialising to XenbusStateInitWait.
Signed-off-by: Filipe Manco <filipe.manco@neclab.eu>
Acked-by: Wei Liu <wei.liu2@citrix.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Pull drm fixes from Dave Airlie:
"Two sets of i915 fixes, one set of vc4 crasher fixes, and a couple of
atmel fixes.
Nothing too out there at this stage, though I think some people are
holidaying so it's been quiet enough"
* tag 'drm-fixes-for-4.8-rc6' of git://people.freedesktop.org/~airlied/linux:
drm/i915: Ignore OpRegion panel type except on select machines
Revert "drm/i915/psr: Make idle_frames sensible again"
drm/i915: Restore lost "Initialized i915" welcome message
drm/vc4: mark vc4_bo_cache_purge() static
drm/i915: Add GEN7_PCODE_MIN_FREQ_TABLE_GT_RATIO_OUT_OF_RANGE to SNB
drm/i915: disable 48bit full PPGTT when vGPU is active
drm/i915: enable vGPU detection for all
drm/atmel-hlcdc: Make ->reset() implementation static
drm: atmel-hlcdc: Fix vertical scaling
drm/vc4: Allow some more signals to be packed with uniform resets.
drm/i915/dvo: Remove dangling call to drm_encoder_cleanup()
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull power management fix from Rafael Wysocki:
"More annotations of tracepoints in the runtime PM framework to prevent
RCU from complaining when that code is invoked from the idle path
(Paul McKenney)"
* tag 'pm-4.8-rc7' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
PM / runtime: Use _rcuidle for runtime suspend tracepoints
|
|
drm-fixes
This pull request brings in a fix for crashes in X on VC4.
* tag 'drm-vc4-fixes-2016-09-14' of https://github.com/anholt/linux:
drm/vc4: mark vc4_bo_cache_purge() static
drm/vc4: Allow some more signals to be packed with uniform resets.
|
|
git://anongit.freedesktop.org/drm-intel into drm-fixes
i915 fixes from Jani.
* tag 'drm-intel-fixes-2016-09-15' of git://anongit.freedesktop.org/drm-intel:
drm/i915: Ignore OpRegion panel type except on select machines
Revert "drm/i915/psr: Make idle_frames sensible again"
drm/i915: Restore lost "Initialized i915" welcome message
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/dledford/rdma
Pull rdma fixes from Doug Ledford:
"Round three of 4.8 rc fixes.
This is likely the last rdma pull request this cycle. The new rxe
driver had a few issues (you probably saw the boot bot bug report) and
they should be addressed now. There are a couple other fixes here,
mainly mlx4. There are still two outstanding issues that need
resolved but I don't think their fix will make this kernel cycle.
Summary:
- Various fixes to rdmavt, ipoib, mlx5, mlx4, rxe"
* tag 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dledford/rdma:
IB/rdmavt: Don't vfree a kzalloc'ed memory region
IB/rxe: Fix kmem_cache leak
IB/rxe: Fix race condition between requester and completer
IB/rxe: Fix duplicate atomic request handling
IB/rxe: Fix kernel panic in udp_setup_tunnel
IB/mlx5: Set source mac address in FTE
IB/mlx5: Enable MAD_IFC commands for IB ports only
IB/mlx4: Diagnostic HW counters are not supported in slave mode
IB/mlx4: Use correct subnet-prefix in QP1 mads under SR-IOV
IB/mlx4: Fix code indentation in QP1 MAD flow
IB/mlx4: Fix incorrect MC join state bit-masking on SR-IOV
IB/ipoib: Don't allow MC joins during light MC flush
IB/rxe: fix GFP_KERNEL in spinlock context
|
|
Pull ARM fixes from Russell King:
"Most of this update are fixes primarily discovered from testing on the
older StrongARM 1110 and PXA systems, as a result of recent interest
from several people in these platforms:
- Locomo interrupt handling incorrectly stores the handler data in
the chip's private data slot: when Locomo is combined with an
interrupt controller who's chip uses the chip private data, this
leads to an oops.
- SA1111 was missing a call to clk_disable() to clean up after a
failed probe.
- SA1111 and PCMCIA suspend/resume was broken:
The PCMCIA "ds" layer was using the legacy bus suspend/resume
methods, which the core PM code is no longer calling as a result of
device_pm_check_callbacks() introduced in commit aa8e54b559479
("PM / sleep: Go direct_complete if driver has no callbacks").
SA1111 was broken due to changes to PCMCIA which makes PCMCIA
suspend itself later than the SA1111 code expects, and resume
before the SA1111 code has initialised access to the pcmcia
sub-device.
- the default SA1111 interrupt mask polarity got messed up when it
was converted to use a dynamic interrupt base number for its
interrupts.
- fix platform_get_irq() error code propagation, which was causing
problems on platforms where the interrupt may not be available at
probe time in DT setups.
- fix the lack of clock to PCMCIA code on PXA platforms, which was
omitted in conversions of PXA to CCF.
- fix an oops in the PXA PCMCIA code caused by a previous commit not
realising that Lubbock is different from the rest of the PXA PCMCIA
drivers.
- ensure that SA1111 low-level PCMCIA drivers propagate their error
codes to the main probe function, rather than the driver silently
accepting a failure.
- fix the sa11xx debugfs reporting of timing information, which
always indicated zero due to the clock being a factor of 1000 out.
- fix the polarity of the status change signal reported from the
sockets.
Lastly, one ARM specific commit from Stefan Agner fixing the LPAE
cache attributes"
* 'fixes' of git://git.armlinux.org.uk/~rmk/linux-arm:
ARM: pxa/lubbock: add pcmcia clock
ARM: locomo: fix locomo irq handling
ARM: 8612/1: LPAE: initialize cache policy correctly
ARM: sa1111: fix missing clk_disable()
ARM: sa1111: fix pcmcia suspend/resume
ARM: sa1111: fix pcmcia interrupt mask polarity
ARM: sa1111: fix error code propagation in sa1111_probe()
pcmcia: lubbock: fix sockets configuration
pcmcia: sa1111: fix propagation of lowlevel board init return code
pcmcia: soc_common: fix SS_STSCHG polarity
pcmcia: sa11xx_base: add units to the timing information
pcmcia: sa11xx_base: fix reporting of timing information
pcmcia: ds: fix suspend/resume
|
|
The userspace memory region 'mr' is allocated with kzalloc in
__rvt_alloc_mr however it is incorrectly being freed with vfree in
__rvt_free_mr. Fix this by using kfree to free it.
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Reviewed-by: Leon Romanovsky <leonro@mellanox.com>
Acked-by: Dennis Dalessandro <dennis.dalessandro@intel.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
|
|
Decrement qp reference when handling error path
in completer to prevent kmem_cache leak.
Fixes: 8700e3e7c485 ("Soft RoCE driver")
Signed-off-by: Yonatan Cohen <yonatanc@mellanox.com>
Signed-off-by: Leon Romanovsky <leon@kernel.org>
Signed-off-by: Doug Ledford <dledford@redhat.com>
|
|
rxe_requester() is sending a pkt with rxe_xmit_packet() and
then calls rxe_update() to update the wqe and qp's psn values.
But sometimes the response is received before the requester
had time to update the wqe in which case the completer
acts on errornous wqe values.
This fix updates the wqe and qp before actually sending
the request and rolls back when xmit fails.
Fixes: 8700e3e7c485 ("Soft RoCE driver")
Signed-off-by: Yonatan Cohen <yonatanc@mellanox.com>
Signed-off-by: Leon Romanovsky <leon@kernel.org>
Signed-off-by: Doug Ledford <dledford@redhat.com>
|
|
When handling ack for atomic opcodes like "fetch&add"
or "cmp&swp", the method send_atomic_ack() saves the ack
before sending it, in case it gets lost and never reach the
requester. In which case the method duplicate_request()
will need to find it using the duplicated request.psn.
But send_atomic_ack() used a wrong psn value and thus
the above ack was never found.
This fix uses the ack.psn to locate the ack in case
its needed.
This fix also copies the ack packet to the skb's control buffer
since duplicate_request() will need it when calling rxe_xmit_packet()
Fixes: 8700e3e7c485 ("Soft RoCE driver")
Signed-off-by: Yonatan Cohen <yonatanc@mellanox.com>
Signed-off-by: Leon Romanovsky <leon@kernel.org>
Signed-off-by: Doug Ledford <dledford@redhat.com>
|
|
Disable creation of a UDP socket for ipv6 when
CONFIG_IPV6 is not enabeld. Since udp_sock_create6()
returns 0 when CONFIG_IPV6 is not set
[ 46.888632] IP: [<c220705a>] setup_udp_tunnel_sock+0x6/0x4f
[ 46.891355] *pdpt = 0000000000000000 *pde = f000ff53f000ff53
[ 46.893918] Oops: 0002 [#1] PREEMPT
[ 46.896014] CPU: 0 PID: 1 Comm: swapper Not tainted 4.7.0-rc4-00001-g8700e3e #1
[ 46.900280] Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS Debian-1.8.2-1 04/01/2014
[ 46.904905] task: cf06c040 ti: cf05e000 task.ti: cf05e000
[ 46.907854] EIP: 0060:[<c220705a>] EFLAGS: 00210246 CPU: 0
[ 46.911137] EIP is at setup_udp_tunnel_sock+0x6/0x4f
[ 46.914070] EAX: 00000044 EBX: 00000001 ECX: cf05fef0 EDX: ca8142e0
[ 46.917236] ESI: c2c4505b EDI: cf05fef0 EBP: cf05fed0 ESP: cf05fed0
[ 46.919836] DS: 007b ES: 007b FS: 0000 GS: 00e0 SS: 0068
[ 46.922046] CR0: 80050033 CR2: 000001fc CR3: 02cec000 CR4: 000006b0
[ 46.924550] Stack:
[ 46.926014] cf05ff10 c1fd4657 ca8142e0 0000000a 00000000 00000000 0000b712 00000008
[ 46.931274] 00000000 6bb5bd01 c1fd48de 00000000 00000000 cf05ff1c 00000000 00000000
[ 46.936122] cf05ff1c c1fd4bdf 00000000 cf05ff28 c2c4507b ffffffff cf05ff88 c2bf1c74
[ 46.942350] Call Trace:
[ 46.944403] [<c1fd4657>] rxe_setup_udp_tunnel+0x8f/0x99
[ 46.947689] [<c1fd48de>] ? net_to_rxe+0x4e/0x4e
[ 46.950567] [<c1fd4bdf>] rxe_net_init+0xe/0xa4
[ 46.953147] [<c2c4507b>] rxe_module_init+0x20/0x4c
[ 46.955448] [<c2bf1c74>] do_one_initcall+0x89/0x113
[ 46.957797] [<c2bf15eb>] ? set_debug_rodata+0xf/0xf
[ 46.959966] [<c2bf1dbc>] ? kernel_init_freeable+0xbe/0x15b
[ 46.962262] [<c2bf1ddc>] kernel_init_freeable+0xde/0x15b
[ 46.964418] [<c232eb54>] kernel_init+0x8/0xd0
[ 46.966618] [<c2333122>] ret_from_kernel_thread+0xe/0x24
[ 46.969592] [<c232eb4c>] ? rest_init+0x6f/0x6f
Fixes: 8700e3e7c485 ("Soft RoCE driver")
Signed-off-by: Yonatan Cohen <yonatanc@mellanox.com>
Signed-off-by: Leon Romanovsky <leon@kernel.org>
Signed-off-by: Doug Ledford <dledford@redhat.com>
|
|
Set the source mac address in the FTE when L2 specification
is provided.
Fixes: 038d2ef87572 ('IB/mlx5: Add flow steering support')
Signed-off-by: Maor Gottlieb <maorg@mellanox.com>
Signed-off-by: Leon Romanovsky <leon@kernel.org>
Signed-off-by: Doug Ledford <dledford@redhat.com>
|
|
MAD_IFC command is supported only for physical functions (PF)
and when physical port is IB. The proposed fix enforces it.
Fixes: d603c809ef91 ("IB/mlx5: Fix decision on using MAD_IFC")
Reported-by: David Chang <dchang@suse.com>
Signed-off-by: Noa Osherovich <noaos@mellanox.com>
Signed-off-by: Leon Romanovsky <leon@kernel.org>
Signed-off-by: Doug Ledford <dledford@redhat.com>
|
