| Age | Commit message (Collapse) | Author |
|---|
|
commit ec484d03ef0df8d34086b95710e355a259cbe1f2 upstream.
The oldest firmware supported by iwlmvm do support getting
the average beacon RSSI. Enable the sta_statistics() call
from mac80211 even on older firmware versions.
Fixes: 33cef9256342 ("iwlwifi: mvm: support beacon statistics for BSS client")
Cc: stable@vger.kernel.org # 4.2+
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit a5baeaeabcca3244782a9b6382ebab6f8a58f583 upstream.
This definition is used by msecs_to_jiffies in milliseconds.
According to the comments, max rexit timeout should be 20ms.
Align with the comments to properly calculate the delay.
Verified on Sunrise Point-LP and Cannon Lake.
Cc: stable@vger.kernel.org
Signed-off-by: Aaron Ma <aaron.ma@canonical.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 22454b79e6de05fa61a2a72d00d2eed798abbb75 upstream.
This will clear the USB_PORT_FEAT_C_CONNECTION bit in case of a hub port reset
only if a device is was attached to the hub port before resetting the hub port.
Using a Lenovo T480s attached to the ultra dock it was not possible to detect
some usb-c devices at the dock usb-c ports because the hub_port_reset code
will clear the USB_PORT_FEAT_C_CONNECTION bit after the actual hub port reset.
Using this device combo the USB_PORT_FEAT_C_CONNECTION bit was set between the
actual hub port reset and the clear of the USB_PORT_FEAT_C_CONNECTION bit.
This ends up with clearing the USB_PORT_FEAT_C_CONNECTION bit after the
new device was attached such that it was not detected.
This patch will not clear the USB_PORT_FEAT_C_CONNECTION bit if there is
currently no device attached to the port before the hub port reset.
This will avoid clearing the connection bit for new attached devices.
Signed-off-by: Dennis Wassenberg <dennis.wassenberg@secunet.com>
Acked-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 2278446e2b7cd33ad894b32e7eb63afc7db6c86e upstream.
Hub driver will try to disable a USB3 device twice at logical disconnect,
racing with xhci_free_dev() callback from the first port disable.
This can be triggered with "udisksctl power-off --block-device <disk>"
or by writing "1" to the "remove" sysfs file for a USB3 device
in 4.17-rc4.
USB3 devices don't have a similar disabled link state as USB2 devices,
and use a U3 suspended link state instead. In this state the port
is still enabled and connected.
hub_port_connect() first disconnects the device, then later it notices
that device is still enabled (due to U3 states) it will try to disable
the port again (set to U3).
The xhci_free_dev() called during device disable is async, so checking
for existing xhci->devs[i] when setting link state to U3 the second time
was successful, even if device was being freed.
The regression was caused by, and whole thing revealed by,
Commit 44a182b9d177 ("xhci: Fix use-after-free in xhci_free_virt_device")
which sets xhci->devs[i]->udev to NULL before xhci_virt_dev() returned.
and causes a NULL pointer dereference the second time we try to set U3.
Fix this by checking xhci->devs[i]->udev exists before setting link state.
The original patch went to stable so this fix needs to be applied there as
well.
Fixes: 44a182b9d177 ("xhci: Fix use-after-free in xhci_free_virt_device")
Cc: <stable@vger.kernel.org>
Reported-by: Jordan Glover <Golden_Miller83@protonmail.ch>
Tested-by: Jordan Glover <Golden_Miller83@protonmail.ch>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Cc: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 8c01db7619f07c85c5cd81ec5eb83608b56c88f5 upstream.
When a UHID_CREATE command is written to the uhid char device, a
copy_from_user() is done from a user pointer embedded in the command.
When the address limit is KERNEL_DS, e.g. as is the case during
sys_sendfile(), this can read from kernel memory. Alternatively,
information can be leaked from a setuid binary that is tricked to write
to the file descriptor. Therefore, forbid UHID_CREATE in these cases.
No other commands in uhid_char_write() are affected by this bug and
UHID_CREATE is marked as "obsolete", so apply the restriction to
UHID_CREATE only rather than to uhid_char_write() entirely.
Thanks to Dmitry Vyukov for adding uhid definitions to syzkaller and to
Jann Horn for commit 9da3f2b740544 ("x86/fault: BUG() when uaccess
helpers fault on kernel addresses"), allowing this bug to be found.
Reported-by: syzbot+72473edc9bf4eb1c6556@syzkaller.appspotmail.com
Fixes: d365c6cfd337 ("HID: uhid: add UHID_CREATE and UHID_DESTROY events")
Cc: <stable@vger.kernel.org> # v3.6+
Cc: Jann Horn <jannh@google.com>
Cc: Andy Lutomirski <luto@kernel.org>
Signed-off-by: Eric Biggers <ebiggers@google.com>
Reviewed-by: Jann Horn <jannh@google.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 2bbb5fa37475d7aa5fa62f34db1623f3da2dfdfa upstream.
Many HP AMD based laptops contain an SMB0001 device like this:
Device (SMBD)
{
Name (_HID, "SMB0001") // _HID: Hardware ID
Name (_CRS, ResourceTemplate () // _CRS: Current Resource Settings
{
IO (Decode16,
0x0B20, // Range Minimum
0x0B20, // Range Maximum
0x20, // Alignment
0x20, // Length
)
IRQ (Level, ActiveLow, Shared, )
{7}
})
}
The legacy style IRQ resource here causes acpi_dev_get_irqresource() to
be called with legacy=true and this message to show in dmesg:
ACPI: IRQ 7 override to edge, high
This causes issues when later on the AMD0030 GPIO device gets enumerated:
Device (GPIO)
{
Name (_HID, "AMDI0030") // _HID: Hardware ID
Name (_CID, "AMDI0030") // _CID: Compatible ID
Name (_UID, Zero) // _UID: Unique ID
Method (_CRS, 0, NotSerialized) // _CRS: Current Resource Settings
{
Name (RBUF, ResourceTemplate ()
{
Interrupt (ResourceConsumer, Level, ActiveLow, Shared, ,, )
{
0x00000007,
}
Memory32Fixed (ReadWrite,
0xFED81500, // Address Base
0x00000400, // Address Length
)
})
Return (RBUF) /* \_SB_.GPIO._CRS.RBUF */
}
}
Now acpi_dev_get_irqresource() gets called with legacy=false, but because
of the earlier override of the trigger-type acpi_register_gsi() returns
-EBUSY (because we try to register the same interrupt with a different
trigger-type) and we end up setting IORESOURCE_DISABLED in the flags.
The setting of IORESOURCE_DISABLED causes platform_get_irq() to call
acpi_irq_get() which is not implemented on x86 and returns -EINVAL.
resulting in the following in dmesg:
amd_gpio AMDI0030:00: Failed to get gpio IRQ: -22
amd_gpio: probe of AMDI0030:00 failed with error -22
The SMB0001 is a "virtual" device in the sense that the only way the OS
interacts with it is through calling a couple of methods to do SMBus
transfers. As such it is weird that it has IO and IRQ resources at all,
because the driver for it is not expected to ever access the hardware
directly.
The Linux driver for the SMB0001 device directly binds to the acpi_device
through the acpi_bus, so we do not need to instantiate a platform_device
for this ACPI device. This commit adds the SMB0001 HID to the
forbidden_id_list, avoiding the instantiating of a platform_device for it.
Not instantiating a platform_device means we will no longer call
acpi_dev_get_irqresource() for the legacy IRQ resource fixing the probe of
the AMDI0030 device failing.
BugLink: https://bugzilla.redhat.com/show_bug.cgi?id=1644013
BugLink: https://bugzilla.kernel.org/show_bug.cgi?id=198715
BugLink: https://bugzilla.kernel.org/show_bug.cgi?id=199523
Reported-by: Lukas Kahnert <openproggerfreak@gmail.com>
Tested-by: Marc <suaefar@googlemail.com>
Cc: All applicable <stable@vger.kernel.org>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit fee05f455ceb5c670cbe48e2f9454ebc4a388554 upstream.
req.gid can be indirectly controlled by user-space, hence leading to
a potential exploitation of the Spectre variant 1 vulnerability.
This issue was detected with the help of Smatch:
vers/misc/sgi-gru/grukdump.c:200 gru_dump_chiplet_request() warn:
potential spectre issue 'gru_base' [w]
Fix this by sanitizing req.gid before calling macro GID_TO_GRU, which
uses it to index gru_base.
Notice that given that speculation windows are large, the policy is
to kill the speculation on the first load and not worry if it can be
completed with a dependent load/store [1].
[1] https://marc.info/?l=linux-kernel&m=152449131114778&w=2
Cc: stable@vger.kernel.org
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit f6501f49199097b99e4e263644d88c90d1ec1060 upstream.
Add another Apple Cinema Display to the list of supported displays
Signed-off-by: Mattias Jacobsson <2pi@mok.nu>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 7c97301285b62a41d6bceded7d964085fc8cc50f upstream.
After building the kernel with Clang, the following section mismatch
warning appears:
WARNING: vmlinux.o(.text+0x3bf19a6): Section mismatch in reference from
the function ssc_probe() to the function
.init.text:atmel_ssc_get_driver_data()
The function ssc_probe() references
the function __init atmel_ssc_get_driver_data().
This is often because ssc_probe lacks a __init
annotation or the annotation of atmel_ssc_get_driver_data is wrong.
Remove __init from atmel_ssc_get_driver_data to get rid of the mismatch.
Signed-off-by: Nathan Chancellor <natechancellor@gmail.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit a77112577667cbda7c6292c52d909636aef31fd9 upstream.
Following on from this patch: https://lkml.org/lkml/2017/11/3/516,
Corsair K70 LUX RGB keyboards also require the DELAY_INIT quirk to
start correctly at boot.
Dmesg output:
usb 1-6: string descriptor 0 read error: -110
usb 1-6: New USB device found, idVendor=1b1c, idProduct=1b33
usb 1-6: New USB device strings: Mfr=1, Product=2, SerialNumber=3
usb 1-6: can't set config #1, error -110
Signed-off-by: Emmanuel Pescosta <emmanuelpescosta099@gmail.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit deefd24228a172d1b27d4a9adbfd2cdacd60ae64 upstream.
Raydium USB touchscreen fails to set config if LPM is enabled:
[ 2.030658] usb 1-8: New USB device found, idVendor=2386, idProduct=3119
[ 2.030659] usb 1-8: New USB device strings: Mfr=1, Product=2, SerialNumber=0
[ 2.030660] usb 1-8: Product: Raydium Touch System
[ 2.030661] usb 1-8: Manufacturer: Raydium Corporation
[ 7.132209] usb 1-8: can't set config #1, error -110
Same behavior can be observed on 2386:3114.
Raydium claims the touchscreen supports LPM under Windows, so I used
Microsoft USB Test Tools (MUTT) [1] to check its LPM status. MUTT shows
that the LPM doesn't work under Windows, either. So let's just disable LPM
for Raydium touchscreens.
[1] https://docs.microsoft.com/en-us/windows-hardware/drivers/usbcon/usb-test-tools
Signed-off-by: Kai-Heng Feng <kai.heng.feng@canonical.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 63529eaa6164ef7ab4b907b25ac3648177e5e78f upstream.
The cdc-acm kernel module currently does not support the Hiro (Conexant)
H05228 USB modem. The patch below adds the device specific information:
idVendor 0x0572
idProduct 0x1349
Signed-off-by: Maarten Jacobs <maarten256@outlook.com>
Acked-by: Oliver Neukum <oneukum@suse.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 432798195bbce1f8cd33d1c0284d0538835e25fb upstream.
I was trying to solve a double free but I introduced a more serious
NULL dereference bug. The problem is that if there is an IRQ which
triggers immediately, then we need "info->uio_dev" but it's not set yet.
This patch puts the original initialization back to how it was and just
sets info->uio_dev to NULL on the error path so it should solve both
the Oops and the double free.
Fixes: f019f07ecf6a ("uio: potential double frees if __uio_register_device() fails")
Reported-by: Mathias Thore <Mathias.Thore@infinera.com>
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Cc: stable <stable@vger.kernel.org>
Tested-by: Mathias Thore <Mathias.Thore@infinera.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 92539d3eda2c090b382699bbb896d4b54e9bdece upstream.
Patch ad608fbcf166 changed how events were subscribed to address an issue
elsewhere. As a side effect of that change, the "add" callback was called
before the event subscription was added to the list of subscribed events,
causing the first event queued by the add callback (and possibly other
events arriving soon afterwards) to be lost.
Fix this by adding the subscription to the list before calling the "add"
callback, and clean up afterwards if that fails.
Fixes: ad608fbcf166 ("media: v4l: event: Prevent freeing event subscriptions while accessed")
Reported-by: Dave Stevenson <dave.stevenson@raspberrypi.org>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Tested-by: Dave Stevenson <dave.stevenson@raspberrypi.org>
Reviewed-by: Hans Verkuil <hans.verkuil@cisco.com>
Tested-by: Hans Verkuil <hans.verkuil@cisco.com>
Cc: stable@vger.kernel.org (for 4.14 and up)
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
[Sakari Ailus: Backported to v4.9 stable]
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
This reverts commit 5824d86b50b8c5f9ecd725f2d74381a23ab1c63b which is
commit 6c3711ec64fd23a9abc8aaf59a9429569a6282df upstream.
You Ling writes that this config option isn't even in 4.4.y yet, so it
causes a regression. Revert the patch because of this.
Reported-by: youling 257 <youling257@gmail.com>
Cc: Johan Hedberg <johan.hedberg@intel.com>
Cc: Marcel Holtmann <marcel@holtmann.org>
Cc: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
This reverts commit 46431d9c28f6859f8e568ac7db92137f1da31100.
This commit fixes a bug in upstream commit a136f59c0a1f ("vb2: Move
buffer cache synchronisation to prepare from queue") which isn't
present in 4.4.
So as a result you get an UNBALANCED message in the kernel log if
this patch is applied:
vb2: counters for queue ffffffc0f3687478, buffer 3: UNBALANCED!
vb2: buf_init: 1 buf_cleanup: 1 buf_prepare: 805 buf_finish: 805
vb2: buf_queue: 806 buf_done: 806
vb2: alloc: 0 put: 0 prepare: 806 finish: 805 mmap: 0
vb2: get_userptr: 0 put_userptr: 0
vb2: attach_dmabuf: 1 detach_dmabuf: 1 map_dmabuf: 805 unmap_dmabuf: 805
vb2: get_dmabuf: 0 num_users: 1609 vaddr: 0 cookie: 805
Reverting this patch solves this regression.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
commit fef912bf860e upstream.
commit 98af4d4df889 upstream.
I got a report from Howard Chen that he saw zram and sysfs race(ie,
zram block device file is created but sysfs for it isn't yet)
when he tried to create new zram devices via hotadd knob.
v4.20 kernel fixes it by [1, 2] but it's too large size to merge
into -stable so this patch fixes the problem by registering defualt
group by Greg KH's approach[3].
This patch should be applied to every stable tree [3.16+] currently
existing from kernel.org because the problem was introduced at 2.6.37
by [4].
[1] fef912bf860e, block: genhd: add 'groups' argument to device_add_disk
[2] 98af4d4df889, zram: register default groups with device_add_disk()
[3] http://kroah.com/log/blog/2013/06/26/how-to-create-a-sysfs-file-correctly/
[4] 33863c21e69e9, Staging: zram: Replace ioctls with sysfs interface
Cc: Sergey Senozhatsky <sergey.senozhatsky@gmail.com>
Cc: Hannes Reinecke <hare@suse.com>
Tested-by: Howard Chen <howardsoc@google.com>
Signed-off-by: Minchan Kim <minchan@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit e3e61f01d755188cb6c2dcf5a244b9c0937c258e ]
If gcc decides not to inline make_sensor_label():
WARNING: vmlinux.o(.text+0x4df549c): Section mismatch in reference from the function .create_device_attrs() to the function .init.text:.make_sensor_label()
The function .create_device_attrs() references
the function __init .make_sensor_label().
This is often because .create_device_attrs lacks a __init
annotation or the annotation of .make_sensor_label is wrong.
As .probe() can be called after freeing of __init memory, all __init
annotiations in the driver are bogus, and should be removed.
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 684238d79ad85c5e19a71bb5818e77e329912fbc ]
To fix:
acerhdf: unknown (unsupported) BIOS version Gateway /LT31 /v1.3307 , please report, aborting!
As can be seen in the context, the BIOS registers haven't changed in
the previous versions, so the assumption is they won't have changed
in this last update for this somewhat older platform either.
Cc: Peter Feuerer <peter@piie.net>
Cc: Darren Hart <dvhart@infradead.org>
Cc: Andy Shevchenko <andy@infradead.org>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Peter Feuerer <peter@piie.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit b33228029d842269e17bba591609e83ed422005d ]
Ensure that clocks for core SoC modules (including TZPC0..9 modules)
are enabled for suspend/resume cycle. This fixes suspend/resume
support on Exynos5422-based Odroid XU3/XU4 boards.
Suggested-by: Joonyoung Shim <jy0922.shim@samsung.com>
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Sylwester Nawrocki <snawrocki@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
commit 91ee5b21ee026c49e4e7483de69b55b8b47042be upstream.
Clang may emit absolute symbol references when building in non-PIC mode,
even when using the default 'small' code model, which is already mostly
position independent to begin with, due to its use of adrp/add pairs
that have a relative range of +/- 4 GB. The remedy is to pass the -fpie
flag, which can be done safely now that the code has been updated to avoid
GOT indirections (which may be emitted due to the compiler assuming that
the PIC/PIE code may end up in a shared library that is subject to ELF
symbol preemption)
Passing -fpie when building code that needs to execute at an a priori
unknown offset is arguably an improvement in any case, and given that
the recent visibility changes allow the PIC build to pass with GCC as
well, let's add -fpie for all arm64 builds rather than only for Clang.
Tested-by: Matthias Kaehlcke <mka@chromium.org>
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Matt Fleming <matt@codeblueprint.co.uk>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: linux-efi@vger.kernel.org
Link: http://lkml.kernel.org/r/20170818194947.19347-5-ard.biesheuvel@linaro.org
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Signed-off-by: Nathan Chancellor <natechancellor@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 0426a4e68f18d75515414361de9e3e1445d2644e upstream.
To prevent the compiler from emitting absolute references to the section
markers when running in PIC mode, override the visibility to 'hidden' for
all contents of asm/sections.h
Tested-by: Matthias Kaehlcke <mka@chromium.org>
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Matt Fleming <matt@codeblueprint.co.uk>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: linux-efi@vger.kernel.org
Link: http://lkml.kernel.org/r/20170818194947.19347-4-ard.biesheuvel@linaro.org
Signed-off-by: Ingo Molnar <mingo@kernel.org>
[nc: Fix conflict due to lack of commit 42b55734030c1 in linux-4.4.y]
Signed-off-by: Nathan Chancellor <natechancellor@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit 59663e42199c93d1d7314d1446f6782fc4b1eb81 ]
This patch has the fix to avoid PHY lockup with 5717/5719/5720 in change
ring and flow control paths. This patch solves the RX hang while doing
continuous ring or flow control parameters with heavy traffic from peer.
Signed-off-by: Siva Reddy Kallam <siva.kallam@broadcom.com>
Acked-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 6503493145cba4413ecd3d4d153faeef4a1e9b85 upstream.
HDMI 2.0 594Mhz modes were incorrectly selecting 25.200Mhz Automatic N value
mode instead of HDMI specification values.
V2: Fix 88.2 Hz N value
Cc: Jani Nikula <jani.nikula@linux.intel.com>
Cc: stable@vger.kernel.org
Signed-off-by: Clint Taylor <clinton.a.taylor@intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/1540493521-1746-2-git-send-email-clinton.a.taylor@intel.com
(cherry picked from commit 5a400aa3c562c4a726b4da286e63c96db905ade1)
Signed-off-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 23d8003907d094f77cf959228e2248d6db819fa7 upstream.
Unfortunately drm_dp_get_mst_branch_device which is called from both
drm_dp_mst_handle_down_rep and drm_dp_mst_handle_up_rep seem to rely
on that mgr->mst_primary is not NULL, which seem to be wrong as it can be
cleared with simultaneous mode set, if probing fails or in other case.
mgr->lock mutex doesn't protect against that as it might just get
assigned to NULL right before, not simultaneously.
There are currently bugs 107738, 108616 bugs which crash in
drm_dp_get_mst_branch_device, caused by this issue.
v2: Refactored the code, as it was nicely noticed.
Fixed Bugzilla bug numbers(second was 108616, but not 108816)
and added links.
[changed title and added stable cc]
Signed-off-by: Lyude Paul <lyude@redhat.com>
Signed-off-by: Stanislav Lisovskiy <stanislav.lisovskiy@intel.com>
Cc: stable@vger.kernel.org
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=108616
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=107738
Link: https://patchwork.freedesktop.org/patch/msgid/20181109090012.24438-1-stanislav.lisovskiy@intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 7f3ef5dedb146e3d5063b6845781ad1bb59b92b5 upstream.
Leaving the DRM driver enabled on reboot or kexec has the annoying
effect of leaving the display generating transactions whilst the
IOMMU has been shut down.
In turn, the IOMMU driver (which shares its interrupt line with
the VOP) starts warning either on shutdown or when entering the
secondary kernel in the kexec case (nothing is expected on that
front).
A cheap way of ensuring that things are nicely shut down is to
register a shutdown callback in the platform driver.
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Tested-by: Vicente Bergas <vicencb@gmail.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Link: https://patchwork.freedesktop.org/patch/msgid/20180805124807.18169-1-marc.zyngier@arm.com
Cc: stable@vger.kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 7ce9a992ffde8ce93d5ae5767362a5c7389ae895 upstream.
Fix an issue with the 32-bit range error path in `rtc_hctosys' where no
error code is set and consequently the successful preceding call result
from `rtc_read_time' is propagated to `rtc_hctosys_ret'. This in turn
makes any subsequent call to `hctosys_show' incorrectly report in sysfs
that the system time has been set from this RTC while it has not.
Set the error to ERANGE then if we can't express the result due to an
overflow.
Signed-off-by: Maciej W. Rozycki <macro@linux-mips.org>
Fixes: b3a5ac42ab18 ("rtc: hctosys: Ensure system time doesn't overflow time_t")
Cc: stable@vger.kernel.org # 4.17+
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 35b69a420bfb56b7b74cb635ea903db05e357bec upstream.
Add support for platforms where pit_shutdown() doesn't work because of a
quirk in the PIT emulation. On these platforms setting the counter register
to zero causes the PIT to start running again, negating the shutdown.
Provide a global variable that controls whether the counter register is
zero'ed, which platform specific code can override.
Signed-off-by: Michael Kelley <mikelley@microsoft.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: "gregkh@linuxfoundation.org" <gregkh@linuxfoundation.org>
Cc: "devel@linuxdriverproject.org" <devel@linuxdriverproject.org>
Cc: "daniel.lezcano@linaro.org" <daniel.lezcano@linaro.org>
Cc: "virtualization@lists.linux-foundation.org" <virtualization@lists.linux-foundation.org>
Cc: "jgross@suse.com" <jgross@suse.com>
Cc: "akataria@vmware.com" <akataria@vmware.com>
Cc: "olaf@aepfle.de" <olaf@aepfle.de>
Cc: "apw@canonical.com" <apw@canonical.com>
Cc: vkuznets <vkuznets@redhat.com>
Cc: "jasowang@redhat.com" <jasowang@redhat.com>
Cc: "marcelo.cerri@canonical.com" <marcelo.cerri@canonical.com>
Cc: KY Srinivasan <kys@microsoft.com>
Cc: stable@vger.kernel.org
Link: https://lkml.kernel.org/r/1541303219-11142-2-git-send-email-mikelley@microsoft.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 991a25194097006ec1e0d2e0814ff920e59e3465 upstream.
On architectures with CBAUDEX == 0 (Alpha and PowerPC), the code in tty_baudrate.c does
not do any limit checking on the tty_baudrate[] array, and in fact a
buffer overrun is possible on both architectures. Add a limit check to
prevent that situation.
This will be followed by a much bigger cleanup/simplification patch.
Signed-off-by: H. Peter Anvin (Intel) <hpa@zytor.com>
Requested-by: Cc: Johan Hovold <johan@kernel.org>
Cc: Jiri Slaby <jslaby@suse.com>
Cc: Al Viro <viro@zeniv.linux.org.uk>
Cc: Richard Henderson <rth@twiddle.net>
Cc: Ivan Kokshaysky <ink@jurassic.park.msu.ru>
Cc: Matt Turner <mattst88@gmail.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Kate Stewart <kstewart@linuxfoundation.org>
Cc: Philippe Ombredanne <pombredanne@nexb.com>
Cc: Eugene Syromiatnikov <esyr@redhat.com>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit be2e1c9dcf76886a83fb1c433a316e26d4ca2550 upstream.
I noticed during the creation of another bugfix that the BCH_CONST_PARAMS
option that is set by DOCG3 breaks setting variable parameters for any
other users of the BCH library code.
The only other user we have today is the MTD_NAND software BCH
implementation (most flash controllers use hardware BCH these days
and are not affected). I considered removing BCH_CONST_PARAMS entirely
because of the inherent conflict, but according to the description in
lib/bch.c there is a significant performance benefit in keeping it.
To avoid the immediate problem of the conflict between MTD_NAND_BCH
and DOCG3, this only sets the constant parameters if MTD_NAND_BCH
is disabled, which should fix the problem for all cases that
are affected. This should also work for all stable kernels.
Note that there is only one machine that actually seems to use the
DOCG3 driver (arch/arm/mach-pxa/mioa701.c), so most users should have
the driver disabled, but it almost certainly shows up if we wanted
to test random kernels on machines that use software BCH in MTD.
Fixes: d13d19ece39f ("mtd: docg3: add ECC correction code")
Cc: stable@vger.kernel.org
Cc: Robert Jarzmik <robert.jarzmik@free.fr>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 4542d623c7134bc1738f8a68ccb6dd546f1c264f upstream.
Commands with protection information included were not truncating the
protection iov_iter to the number of protection bytes in the command.
This resulted in vhost_scsi mis-calculating the size of the protection
SGL in vhost_scsi_calc_sgls(), and including both the protection and
data SG entries in the protection SGL.
Fixes: 09b13fa8c1a1 ("vhost/scsi: Add ANY_LAYOUT support in vhost_scsi_handle_vq")
Signed-off-by: Greg Edwards <gedwards@ddn.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Fixes: 09b13fa8c1a1093e9458549ac8bb203a7c65c62a
Cc: stable@vger.kernel.org
Reviewed-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit c09bcc91bb94ed91f1391bffcbe294963d605732 upstream.
Reading the registers without waiting for engine idle returns
unpredictable values. These unpredictable values result in display
corruption - if atyfb_imageblit reads the content of DP_PIX_WIDTH with the
bit DP_HOST_TRIPLE_EN set (from previous invocation), the driver would
never ever clear the bit, resulting in display corruption.
We don't want to wait for idle because it would degrade performance, so
this patch modifies the driver so that it never reads accelerator
registers.
HOST_CNTL doesn't have to be read, we can just write it with
HOST_BYTE_ALIGN because no other part of the driver cares if
HOST_BYTE_ALIGN is set.
DP_PIX_WIDTH is written in the functions atyfb_copyarea and atyfb_fillrect
with the default value and in atyfb_imageblit with the value set according
to the source image data.
Signed-off-by: Mikulas Patocka <mpatocka@redhat.com>
Reviewed-by: Ville Syrjälä <syrjala@sci.fi>
Cc: stable@vger.kernel.org
Signed-off-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 3c6c6a7878d00a3ac997a779c5b9861ff25dfcc8 upstream.
The code for manual bit triple is not endian-clean. It builds the variable
"hostdword" using byte accesses, therefore we must read the variable with
"le32_to_cpu".
The patch also enables (hardware or software) bit triple only if the image
is monochrome (image->depth). If we want to blit full-color image, we
shouldn't use the triple code.
Signed-off-by: Mikulas Patocka <mpatocka@redhat.com>
Reviewed-by: Ville Syrjälä <syrjala@sci.fi>
Cc: stable@vger.kernel.org
Signed-off-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 8985167ecf57f97061599a155bb9652c84ea4913 upstream.
When driver is built as module and DT node contains clocks compatible
(e.g. "samsung,s2mps11-clk"), the module will not be autoloaded because
module aliases won't match.
The modalias from uevent: of:NclocksT<NULL>Csamsung,s2mps11-clk
The modalias from driver: platform:s2mps11-clk
The devices are instantiated by parent's MFD. However both Device Tree
bindings and parent define the compatible for clocks devices. In case
of module matching this DT compatible will be used.
The issue will not happen if this is a built-in (no need for module
matching) or when clocks DT node does not contain compatible (not
correct from bindings perspective but working for driver).
Note when backporting to stable kernels: adjust the list of device ID
entries.
Cc: <stable@vger.kernel.org>
Fixes: 53c31b3437a6 ("mfd: sec-core: Add of_compatible strings for clock MFD cells")
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Acked-by: Stephen Boyd <sboyd@kernel.org>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit 4dc69c1c1fff2f587f8e737e70b4a4e7565a5c94 ]
Using memcpy() from a string that is shorter than the length copied means
the destination buffer is being filled with arbitrary data from the kernel
rodata segment. Instead, use strncpy() which will fill the trailing bytes
with zeros.
This was found with the future CONFIG_FORTIFY_SOURCE feature.
Cc: Daniel Micay <danielmicay@gmail.com>
Signed-off-by: Kees Cook <keescook@chromium.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 44c445c3d1b4eacff23141fa7977c3b2ec3a45c9 ]
This patch fixes a race condition that can result into the interface being
up and carrier on, but with transmits disabled in the hardware.
The bug may show up by repeatedly IFF_DOWN+IFF_UP the interface, which
allows e1000_watchdog() interleave with e1000_down().
CPU x CPU y
--------------------------------------------------------------------
e1000_down():
netif_carrier_off()
e1000_watchdog():
if (carrier == off) {
netif_carrier_on();
enable_hw_transmit();
}
disable_hw_transmit();
e1000_watchdog():
/* carrier on, do nothing */
Signed-off-by: Vincenzo Maffione <v.maffione@gmail.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 5983587c8c5ef00d6886477544ad67d495bc5479 ]
Currently if the stat type is invalid then data[i] is being set
either by dereferencing a null pointer p, or it is reading from
an incorrect previous location if we had a valid stat type
previously. Fix this by skipping over the read of p on an invalid
stat type.
Detected by CoverityScan, CID#113385 ("Explicit null dereferenced")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Reviewed-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
commit 4c1458df9635c7e3ced155f594d2e7dfd7254e21 upstream.
Fixes: 6246b8a1d26c7c ("[SCSI] qla2xxx: Enhancements to support ISP83xx.")
Fixes: 1bb395485160d2 ("qla2xxx: Correct iiDMA-update calling conventions.")
Cc: <stable@vger.kernel.org>
Signed-off-by: Himanshu Madhani <himanshu.madhani@cavium.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit e4f3aa2e1e67bb48dfbaaf1cad59013d5a5bc276 upstream.
There is another cast from unsigned long to int which causes
a bounds check to fail with specially crafted input. The value is
then used as an index in the slot array in cdrom_slot_status().
This issue is similar to CVE-2018-16658 and CVE-2018-10940.
Signed-off-by: Young_X <YangX92@hotmail.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Cc: Ben Hutchings <ben.hutchings@codethink.co.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit bd24db04101f45a9c1d874fe21b0c7eab7bcadec ]
The driver ignored the width alignment which exists due to the UYVY
colorspace format. Fix the width alignment and make use of the the
provided v4l2 helper function to set the width, height and all
alignments in one.
Fixes: 963ddc63e20d ("[media] media: tvp5150: Add cropping support")
Signed-off-by: Marco Felsch <m.felsch@pengutronix.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit 8344498721059754e09d30fe255a12dab8fb03ef ]
The SC16IS752 is a dual-channel device. The two channels are largely
independent, but the IRQ signals are wired together as an open-drain,
active low signal which will be driven low while either of the
channels requires attention, which can be for significant periods of
time until operations complete and the interrupt can be acknowledged.
In that respect it is should be treated as a true level-sensitive IRQ.
The kernel, however, needs to be able to exit interrupt context in
order to use I2C or SPI to access the device registers (which may
involve sleeping). Therefore the interrupt needs to be masked out or
paused in some way.
The usual way to manage sleeping from within an interrupt handler
is to use a threaded interrupt handler - a regular interrupt routine
does the minimum amount of work needed to triage the interrupt before
waking the interrupt service thread. If the threaded IRQ is marked as
IRQF_ONESHOT the kernel will automatically mask out the interrupt
until the thread runs to completion. The sc16is7xx driver used to
use a threaded IRQ, but a patch switched to using a kthread_worker
in order to set realtime priorities on the handler thread and for
other optimisations. The end result is non-threaded IRQ that
schedules some work then returns IRQ_HANDLED, making the kernel
think that all IRQ processing has completed.
The work-around to prevent a constant stream of interrupts is to
mark the interrupt as edge-sensitive rather than level-sensitive,
but interpreting an active-low source as a falling-edge source
requires care to prevent a total cessation of interrupts. Whereas
an edge-triggering source will generate a new edge for every interrupt
condition a level-triggering source will keep the signal at the
interrupting level until it no longer requires attention; in other
words, the host won't see another edge until all interrupt conditions
are cleared. It is therefore vital that the interrupt handler does not
exit with an outstanding interrupt condition, otherwise the kernel
will not receive another interrupt unless some other operation causes
the interrupt state on the device to be cleared.
The existing sc16is7xx driver has a very simple interrupt "thread"
(kthread_work job) that processes interrupts on each channel in turn
until there are no more. If both channels are active and the first
channel starts interrupting while the handler for the second channel
is running then it will not be detected and an IRQ stall ensues. This
could be handled easily if there was a shared IRQ status register, or
a convenient way to determine if the IRQ had been deasserted for any
length of time, but both appear to be lacking.
Avoid this problem (or at least make it much less likely to happen)
by reducing the granularity of per-channel interrupt processing
to one condition per iteration, only exiting the overall loop when
both channels are no longer interrupting.
Signed-off-by: Phil Elwell <phil@raspberrypi.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit c5d59528e24ad22500347b199d52b9368e686a42 ]
altera_hw_filt_init() which calls append_internal() assumes
that the node was successfully linked in while in fact it can
silently fail. So the call-site needs to set return to -ENOMEM
on append_internal() returning NULL and exit through the err path.
Fixes: 349bcf02e361 ("[media] Altera FPGA based CI driver module")
Signed-off-by: Nicholas Mc Guire <hofrat@osadl.org>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit 538f66ba204944470a653a4cccc5f8befdf97c22 ]
A DMM timeout "timed out waiting for done" has been observed on DRA7
devices. The timeout happens rarely, and only when the system is under
heavy load.
Debugging showed that the timeout can be made to happen much more
frequently by optimizing the DMM driver, so that there's almost no code
between writing the last DMM descriptors to RAM, and writing to DMM
register which starts the DMM transaction.
The current theory is that a wmb() does not properly ensure that the
data written to RAM is observable by all the components in the system.
This DMM timeout has caused interesting (and rare) bugs as the error
handling was not functioning properly (the error handling has been fixed
in previous commits):
* If a DMM timeout happened when a GEM buffer was being pinned for
display on the screen, a timeout error would be shown, but the driver
would continue programming DSS HW with broken buffer, leading to
SYNCLOST floods and possible crashes.
* If a DMM timeout happened when other user (say, video decoder) was
pinning a GEM buffer, a timeout would be shown but if the user
handled the error properly, no other issues followed.
* If a DMM timeout happened when a GEM buffer was being released, the
driver does not even notice the error, leading to crashes or hang
later.
This patch adds wmb() and readl() calls after the last bit is written to
RAM, which should ensure that the execution proceeds only after the data
is actually in RAM, and thus observable by DMM.
The read-back should not be needed. Further study is required to understand
if DMM is somehow special case and read-back is ok, or if DRA7's memory
barriers do not work correctly.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit 33a1a7be198657c8ca26ad406c4d2a89b7162bcc ]
The issue is found by a fuzzing test.
If tty_find_polling_driver() recevies an incorrect input such as
',,' or '0b', the len becomes 0 and strncmp() always return 0.
In this case, a null p->ops->poll_init() is called and it causes a kernel
panic.
Fix this by checking name length against zero in tty_find_polling_driver().
$echo ,, > /sys/module/kgdboc/parameters/kgdboc
[ 20.804451] WARNING: CPU: 1 PID: 104 at drivers/tty/serial/serial_core.c:457
uart_get_baud_rate+0xe8/0x190
[ 20.804917] Modules linked in:
[ 20.805317] CPU: 1 PID: 104 Comm: sh Not tainted 4.19.0-rc7ajb #8
[ 20.805469] Hardware name: linux,dummy-virt (DT)
[ 20.805732] pstate: 20000005 (nzCv daif -PAN -UAO)
[ 20.805895] pc : uart_get_baud_rate+0xe8/0x190
[ 20.806042] lr : uart_get_baud_rate+0xc0/0x190
[ 20.806476] sp : ffffffc06acff940
[ 20.806676] x29: ffffffc06acff940 x28: 0000000000002580
[ 20.806977] x27: 0000000000009600 x26: 0000000000009600
[ 20.807231] x25: ffffffc06acffad0 x24: 00000000ffffeff0
[ 20.807576] x23: 0000000000000001 x22: 0000000000000000
[ 20.807807] x21: 0000000000000001 x20: 0000000000000000
[ 20.808049] x19: ffffffc06acffac8 x18: 0000000000000000
[ 20.808277] x17: 0000000000000000 x16: 0000000000000000
[ 20.808520] x15: ffffffffffffffff x14: ffffffff00000000
[ 20.808757] x13: ffffffffffffffff x12: 0000000000000001
[ 20.809011] x11: 0101010101010101 x10: ffffff880d59ff5f
[ 20.809292] x9 : ffffff880d59ff5e x8 : ffffffc06acffaf3
[ 20.809549] x7 : 0000000000000000 x6 : ffffff880d59ff5f
[ 20.809803] x5 : 0000000080008001 x4 : 0000000000000003
[ 20.810056] x3 : ffffff900853e6b4 x2 : dfffff9000000000
[ 20.810693] x1 : ffffffc06acffad0 x0 : 0000000000000cb0
[ 20.811005] Call trace:
[ 20.811214] uart_get_baud_rate+0xe8/0x190
[ 20.811479] serial8250_do_set_termios+0xe0/0x6f4
[ 20.811719] serial8250_set_termios+0x48/0x54
[ 20.811928] uart_set_options+0x138/0x1bc
[ 20.812129] uart_poll_init+0x114/0x16c
[ 20.812330] tty_find_polling_driver+0x158/0x200
[ 20.812545] configure_kgdboc+0xbc/0x1bc
[ 20.812745] param_set_kgdboc_var+0xb8/0x150
[ 20.812960] param_attr_store+0xbc/0x150
[ 20.813160] module_attr_store+0x40/0x58
[ 20.813364] sysfs_kf_write+0x8c/0xa8
[ 20.813563] kernfs_fop_write+0x154/0x290
[ 20.813764] vfs_write+0xf0/0x278
[ 20.813951] __arm64_sys_write+0x84/0xf4
[ 20.814400] el0_svc_common+0xf4/0x1dc
[ 20.814616] el0_svc_handler+0x98/0xbc
[ 20.814804] el0_svc+0x8/0xc
[ 20.822005] Unable to handle kernel NULL pointer dereference at virtual address 0000000000000000
[ 20.826913] Mem abort info:
[ 20.827103] ESR = 0x84000006
[ 20.827352] Exception class = IABT (current EL), IL = 16 bits
[ 20.827655] SET = 0, FnV = 0
[ 20.827855] EA = 0, S1PTW = 0
[ 20.828135] user pgtable: 4k pages, 39-bit VAs, pgdp = (____ptrval____)
[ 20.828484] [0000000000000000] pgd=00000000aadee003, pud=00000000aadee003, pmd=0000000000000000
[ 20.829195] Internal error: Oops: 84000006 [#1] SMP
[ 20.829564] Modules linked in:
[ 20.829890] CPU: 1 PID: 104 Comm: sh Tainted: G W 4.19.0-rc7ajb #8
[ 20.830545] Hardware name: linux,dummy-virt (DT)
[ 20.830829] pstate: 60000085 (nZCv daIf -PAN -UAO)
[ 20.831174] pc : (null)
[ 20.831457] lr : serial8250_do_set_termios+0x358/0x6f4
[ 20.831727] sp : ffffffc06acff9b0
[ 20.831936] x29: ffffffc06acff9b0 x28: ffffff9008d7c000
[ 20.832267] x27: ffffff900969e16f x26: 0000000000000000
[ 20.832589] x25: ffffff900969dfb0 x24: 0000000000000000
[ 20.832906] x23: ffffffc06acffad0 x22: ffffff900969e160
[ 20.833232] x21: 0000000000000000 x20: ffffffc06acffac8
[ 20.833559] x19: ffffff900969df90 x18: 0000000000000000
[ 20.833878] x17: 0000000000000000 x16: 0000000000000000
[ 20.834491] x15: ffffffffffffffff x14: ffffffff00000000
[ 20.834821] x13: ffffffffffffffff x12: 0000000000000001
[ 20.835143] x11: 0101010101010101 x10: ffffff880d59ff5f
[ 20.835467] x9 : ffffff880d59ff5e x8 : ffffffc06acffaf3
[ 20.835790] x7 : 0000000000000000 x6 : ffffff880d59ff5f
[ 20.836111] x5 : c06419717c314100 x4 : 0000000000000007
[ 20.836419] x3 : 0000000000000000 x2 : 0000000000000000
[ 20.836732] x1 : 0000000000000001 x0 : ffffff900969df90
[ 20.837100] Process sh (pid: 104, stack limit = 0x(____ptrval____))
[ 20.837396] Call trace:
[ 20.837566] (null)
[ 20.837816] serial8250_set_termios+0x48/0x54
[ 20.838089] uart_set_options+0x138/0x1bc
[ 20.838570] uart_poll_init+0x114/0x16c
[ 20.838834] tty_find_polling_driver+0x158/0x200
[ 20.839119] configure_kgdboc+0xbc/0x1bc
[ 20.839380] param_set_kgdboc_var+0xb8/0x150
[ 20.839658] param_attr_store+0xbc/0x150
[ 20.839920] module_attr_store+0x40/0x58
[ 20.840183] sysfs_kf_write+0x8c/0xa8
[ 20.840183] sysfs_kf_write+0x8c/0xa8
[ 20.840440] kernfs_fop_write+0x154/0x290
[ 20.840702] vfs_write+0xf0/0x278
[ 20.840942] __arm64_sys_write+0x84/0xf4
[ 20.841209] el0_svc_common+0xf4/0x1dc
[ 20.841471] el0_svc_handler+0x98/0xbc
[ 20.841713] el0_svc+0x8/0xc
[ 20.842057] Code: bad PC value
[ 20.842764] ---[ end trace a8835d7de79aaadf ]---
[ 20.843134] Kernel panic - not syncing: Fatal exception
[ 20.843515] SMP: stopping secondary CPUs
[ 20.844289] Kernel Offset: disabled
[ 20.844634] CPU features: 0x0,21806002
[ 20.844857] Memory Limit: none
[ 20.845172] ---[ end Kernel panic - not syncing: Fatal exception ]---
Signed-off-by: Miles Chen <miles.chen@mediatek.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 9e753ba9b9b405e3902d9f08aec5f2ea58a0c317 upstream.
Commit d595567dc4f0 (MD: fix invalid stored role for a disk) broke linear
hotadd. Let's only fix the role for disks in raid1/10.
Based on Guoqing's original patch.
Reported-by: kernel test robot <rong.a.chen@intel.com>
Cc: Gioh Kim <gi-oh.kim@profitbricks.com>
Cc: Guoqing Jiang <gqjiang@suse.com>
Signed-off-by: Shaohua Li <shli@fb.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 1dc6bd5e39a29453bdcc17348dd2a89f1aa4004e upstream.
Fix child-node lookup during probe, which ended up searching the whole
device tree depth-first starting at the parent rather than just matching
on its children.
To make things worse, the parent pmc node could end up being prematurely
freed as of_find_node_by_name() drops a reference to its first argument.
Fixes: 3568df3d31d6 ("soc: tegra: Add thermal reset (thermtrip) support to PMC")
Cc: stable <stable@vger.kernel.org> # 4.0
Cc: Mikko Perttunen <mperttunen@nvidia.com>
Signed-off-by: Johan Hovold <johan@kernel.org>
Reviewed-by: Mikko Perttunen <mperttunen@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit afeaade90db4c5dab93f326d9582be1d5954a198 upstream.
The v4l2-compliance tool complains if a video doesn't start
with a zero sequence number.
While this shouldn't cause any real problem for apps, let's
make it happier, in order to better check the v4l2-compliance
differences before and after patchsets.
This is actually an old issue. It is there since at least its
videobuf2 conversion, e. g. changeset 3829fadc461 ("[media]
em28xx: convert to videobuf2"), if VB1 wouldn't suffer from
the same issue.
Cc: stable@vger.kernel.org
Fixes: d3829fadc461 ("[media] em28xx: convert to videobuf2")
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 15644bfa195bd166d0a5ed76ae2d587f719c3dac upstream.
Instead of using a register value, use an AMUX name, as otherwise
VIDIOC_G_AUDIO would fail.
Cc: stable@vger.kernel.org
Fixes: 766ed64de554 ("V4L/DVB (11827): Add support for Terratec Grabster AV350")
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit f823ce2a1202d47110a7ef86b65839f0be8adc38 upstream.
Follow the V4L2 spec, as warned by v4l2-compliance:
warn: v4l2-test-formats.cpp(732): TRY_FMT cannot handle an invalid pixelformat.
warn: v4l2-test-formats.cpp(733): This may or may not be a problem. For more information see:
warn: v4l2-test-formats.cpp(734): http://www.mail-archive.com/linux-media@vger.kernel.org/msg56550.html
Cc: stable@vger.kernel.org
Fixes: bddcf63313c6 ("V4L/DVB (9927): em28xx: use a more standard way to specify video formats")
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 1bd54d851f50dea6af30c3e6ff4f3e9aab5558f9 upstream.
kgdboc_option_setup does not check input argument before passing it
to strlen. The argument would be a NULL pointer if "ekgdboc", without
its value, is set in command line and thus cause the following panic.
PANIC: early exception 0xe3 IP 10:ffffffff8fbbb620 error 0 cr2 0x0
[ 0.000000] CPU: 0 PID: 0 Comm: swapper Not tainted 4.18-rc8+ #1
[ 0.000000] RIP: 0010:strlen+0x0/0x20
...
[ 0.000000] Call Trace
[ 0.000000] ? kgdboc_option_setup+0x9/0xa0
[ 0.000000] ? kgdboc_early_init+0x6/0x1b
[ 0.000000] ? do_early_param+0x4d/0x82
[ 0.000000] ? parse_args+0x212/0x330
[ 0.000000] ? rdinit_setup+0x26/0x26
[ 0.000000] ? parse_early_options+0x20/0x23
[ 0.000000] ? rdinit_setup+0x26/0x26
[ 0.000000] ? parse_early_param+0x2d/0x39
[ 0.000000] ? setup_arch+0x2f7/0xbf4
[ 0.000000] ? start_kernel+0x5e/0x4c2
[ 0.000000] ? load_ucode_bsp+0x113/0x12f
[ 0.000000] ? secondary_startup_64+0xa5/0xb0
This patch adds a check to prevent the panic.
Cc: stable@vger.kernel.org
Cc: jason.wessel@windriver.com
Cc: gregkh@linuxfoundation.org
Cc: jslaby@suse.com
Signed-off-by: He Zhe <zhe.he@windriver.com>
Reviewed-by: Daniel Thompson <daniel.thompson@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
