| Age | Commit message (Collapse) | Author |
|---|
|
commit b091ac616846a1da75b1f2566b41255ce7f0e0a6 upstream.
During disk scan and revalidation done with sd_revalidate(), the zones
of a zoned disk are checked using the helper function
blk_revalidate_disk_zones() if a configuration change is detected
(change in the number of zones or zone size). The function
blk_revalidate_disk_zones() issues report_zones calls that are very
large, that is, to obtain zone information for all zones of the disk
with a single command. The size of the report zones command buffer
necessary for such large request generally is lower than the disk
max_hw_sectors and KMALLOC_MAX_SIZE (4MB) and succeeds on boot (no
memory fragmentation), but often fail at run time (e.g. hot-plug
event). This causes the disk revalidation to fail and the disk
capacity to be changed to 0.
This problem can be avoided by using vmalloc() instead of kmalloc() for
the buffer allocation. To limit the amount of memory to be allocated,
this patch also introduces the arbitrary SD_ZBC_REPORT_MAX_ZONES
maximum number of zones to report with a single report zones command.
This limit may be lowered further to satisfy the disk max_hw_sectors
limit. Finally, to ensure that the vmalloc-ed buffer can always be
mapped in a request, the buffer size is further limited to at most
queue_max_segments() pages, allowing successful mapping of the buffer
even in the worst case scenario where none of the buffer pages are
contiguous.
Fixes: 515ce6061312 ("scsi: sd_zbc: Fix sd_zbc_report_zones() buffer allocation")
Fixes: e76239a3748c ("block: add a report_zones method")
Cc: stable@vger.kernel.org
Reviewed-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Damien Le Moal <damien.lemoal@wdc.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 541e4095f388c196685685633c950cb9b97f8039 upstream.
Silence error prints in case of EPROBE_DEFER. This avoids
multiple/duplicate defer prints during boot.
Cc: <stable@vger.kernel.org>
Signed-off-by: Keerthy <j-keerthy@ti.com>
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 89fea04c85e85f21ef4937611055abce82330d48 upstream.
Each iteration of for_each_child_of_node puts the previous node, but in
the case of a break from the middle of the loop, there is no put, thus
causing a memory leak. Hence add an of_node_put before the break.
Issue found with Coccinelle.
Cc: <stable@vger.kernel.org>
Signed-off-by: Nishka Dasgupta <nishkadg.linux@gmail.com>
[Bartosz: tweaked the commit message]
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit f5b07b04e5f090a85d1e96938520f2b2b58e4a8e upstream.
If we have to drop the seqcount & rcu lock to perform a krealloc, we
have to restart the loop. In doing so, be careful not to lose track of
the already acquired exclusive fence.
Fixes: fedf54132d24 ("dma-buf: Restart reservation_object_get_fences_rcu() after writes")
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Cc: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Cc: Christian König <christian.koenig@amd.com>
Cc: Alex Deucher <alexander.deucher@amd.com>
Cc: Sumit Semwal <sumit.semwal@linaro.org>
Cc: stable@vger.kernel.org #v4.10
Reviewed-by: Christian König <christian.koenig@amd.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190604125323.21396-1-chris@chris-wilson.co.uk
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 5e383a9798990c69fc759a4930de224bb497e62c upstream.
The debugfs take reference on fence without dropping them.
Signed-off-by: Jérôme Glisse <jglisse@redhat.com>
Cc: Christian König <christian.koenig@amd.com>
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Cc: Sumit Semwal <sumit.semwal@linaro.org>
Cc: linux-media@vger.kernel.org
Cc: dri-devel@lists.freedesktop.org
Cc: linaro-mm-sig@lists.linaro.org
Cc: Stéphane Marchesin <marcheu@chromium.org>
Cc: stable@vger.kernel.org
Reviewed-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Sumit Semwal <sumit.semwal@linaro.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20181206161840.6578-1-jglisse@redhat.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit 99d31cbd8953c6929da978bf049ab0f0b4e503d9 ]
Fix tx reporter's diagnose callback. Propagate error when failing to
gather diagnostics information or failing to print diagnostic data per
queue.
Fixes: de8650a82071 ("net/mlx5e: Add tx reporter support")
Signed-off-by: Aya Levin <ayal@mellanox.com>
Reviewed-by: Tariq Toukan <tariqt@mellanox.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit 39825350ae2a52f8513741b36e42118bd80dd689 ]
Fix timeout recover function to return a meaningful return value.
When an interrupt was not sent by the FW, return IO error instead of
'true'.
Fixes: c7981bea48fb ("net/mlx5e: Fix return status of TX reporter timeout recover")
Signed-off-by: Aya Levin <ayal@mellanox.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Reviewed-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit db849faa9bef993a1379dc510623f750a72fa7ce ]
CQE checksum full mode in new HW, provides a full checksum of rx frame.
Covering bytes starting from eth protocol up to last byte in the received
frame (frame_size - ETH_HLEN), as expected by the stack.
Fixing up skb->csum by the driver is not required in such case. This fix
is to avoid wrong checksum calculation in drivers which already support
the new hardware with the new checksum mode.
Fixes: 85327a9c4150 ("net/mlx5: Update the list of the PCI supported devices")
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit 914adbb1bcf89478ac138318d28b302704564d59 ]
GRE entropy calculation is a single bit per card, and not per port.
Force disable GRE entropy calculation upon the first GRE encap rule,
and release the force at the last GRE encap rule removal. This is done
per port.
Fixes: 97417f6182f8 ("net/mlx5e: Fix GRE key by controlling port tunnel entropy calculation")
Signed-off-by: Eli Britstein <elibr@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit 7d8b16b9facb0dd81d1469808dd9a575fa1d525a ]
Fix checksumming after decryption.
Signed-off-by: Andreas Steinmetz <ast@domdv.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit 095c02da80a41cf6d311c504d8955d6d1c2add10 ]
Fix use-after-free of skb when rx_handler returns RX_HANDLER_PASS.
Signed-off-by: Andreas Steinmetz <ast@domdv.de>
Acked-by: Willem de Bruijn <willemb@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit ef1ce7d7b67b46661091c7ccc0396186b7a247ef ]
Check return value from mlx5e_attach_netdev, add error path on failure.
Fixes: 48935bbb7ae8 ("net/mlx5e: IPoIB, Add netdevice profile skeleton")
Signed-off-by: Aya Levin <ayal@mellanox.com>
Reviewed-by: Feras Daoud <ferasda@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit 107e47cc80ec37cb332bd41b22b1c7779e22e018 ]
vrf_process_v4_outbound() and vrf_process_v6_outbound() do routing
using ip/ipv6 addresses, but don't make sure the header is available
in skb->data[] (skb_headlen() is less then header size).
Case:
1) igb driver from intel.
2) Packet size is greater then 255.
3) MPLS forwards to VRF device.
So, patch adds pskb_may_pull() calls in vrf_process_v4/v6_outbound()
functions.
Signed-off-by: Peter Kosyh <p.kosyh@gmail.com>
Reviewed-by: David Ahern <dsa@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit a261e3797506bd561700be643fe1a85bf81e9661 ]
The onboard sky2 NIC on ASUS P6T WS PRO doesn't work after PM resume
due to the infamous IRQ problem. Disabling MSI works around it, so
let's add it to the blacklist.
Unfortunately the BIOS on the machine doesn't fill the standard
DMI_SYS_* entry, so we pick up DMI_BOARD_* entries instead.
BugLink: https://bugzilla.suse.com/show_bug.cgi?id=1142496
Reported-and-tested-by: Marcus Seyfarth <m.seyfarth@gmail.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit fe4e8db0392a6c2e795eb89ef5fcd86522e66248 ]
On RTL8411b the RX unit gets confused if the PHY is powered-down.
This was reported in [0] and confirmed by Realtek. Realtek provided
a sequence to fix the RX unit after PHY wakeup.
The issue itself seems to have been there longer, the Fixes tag
refers to where the fix applies properly.
[0] https://bugzilla.redhat.com/show_bug.cgi?id=1692075
Fixes: a99790bf5c7f ("r8169: Reinstate ASPM Support")
Tested-by: Ionut Radu <ionut.radu@gmail.com>
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit 4993e5b37e8bcb55ac90f76eb6d2432647273747 ]
Ben Hutchings says:
"This is the wrong place to change the queue mapping.
stmmac_xmit() is called with a specific TX queue locked,
and accessing a different TX queue results in a data race
for all of that queue's state.
I think this commit should be reverted upstream and in all
stable branches. Instead, the driver should implement the
ndo_select_queue operation and override the queue mapping there."
Fixes: c5acdbee22a1 ("net: stmmac: Send TSO packets always from Queue 0")
Suggested-by: Ben Hutchings <ben@decadent.org.uk>
Signed-off-by: Jose Abreu <joabreu@synopsys.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit 0cea0e1148fe134a4a3aaf0b1496f09241fb943a ]
The RX power read from the SFP uses units of 0.1uW. This must be
scaled to units of uW for HWMON. This requires a divide by 10, not the
current 100.
With this change in place, sensors(1) and ethtool -m agree:
sff2-isa-0000
Adapter: ISA adapter
in0: +3.23 V
temp1: +33.1 C
power1: 270.00 uW
power2: 200.00 uW
curr1: +0.01 A
Laser output power : 0.2743 mW / -5.62 dBm
Receiver signal average optical power : 0.2014 mW / -6.96 dBm
Reported-by: chris.healy@zii.aero
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Fixes: 1323061a018a ("net: phy: sfp: Add HWMON support for module sensors")
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit 7b75e49de424ceb53d13e60f35d0a73765626fda ]
Add a 1ms delay after reset deactivation. Otherwise the chip returns
bogus ID value. This is observed with 88E6390 (Peridot) chip.
Signed-off-by: Baruch Siach <baruch@tkos.co.il>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit 35cbef9863640f06107144687bd13151bc2e8ce3 ]
Currently we silently ignore filters if we cannot meet the filter
requirements. This will lead to the MAC dropping packets that are
expected to pass. A better solution would be to set the NIC to promisc
mode when the required filters cannot be met.
Also correct the number of MDF filters supported. It should be 17,
not 16.
Signed-off-by: Justin Chen <justinpopo6@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit be4363bdf0ce9530f15aa0a03d1060304d116b15 ]
There is an extra rcu_read_unlock left in netvsc_recv_callback(),
after a previous patch that removes RCU from this function.
This patch removes the extra RCU unlock.
Fixes: 345ac08990b8 ("hv_netvsc: pass netvsc_device to receive callback")
Signed-off-by: Haiyang Zhang <haiyangz@microsoft.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit fdd258d49e88a9e0b49ef04a506a796f1c768a8e ]
cfhsi_exit_module() calls unregister_netdev() under rtnl_lock().
but unregister_netdev() internally calls rtnl_lock().
So deadlock would occur.
Fixes: c41254006377 ("caif-hsi: Add rtnl support")
Signed-off-by: Taehee Yoo <ap420073@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit ea811b795df24644a8eb760b493c43fba4450677 ]
This patch fixes an issue seen on Power systems with bnx2x which results
in the skb is NULL WARN_ON in bnx2x_free_tx_pkt firing due to the skb
pointer getting loaded in bnx2x_free_tx_pkt prior to the hw_cons
load in bnx2x_tx_int. Adding a read memory barrier resolves the issue.
Signed-off-by: Brian King <brking@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit bd293d071ffe65e645b4d8104f9d8fe15ea13862 upstream.
When thin-volume is built on loop device, if available memory is low,
the following deadlock can be triggered:
One process P1 allocates memory with GFP_FS flag, direct alloc fails,
memory reclaim invokes memory shrinker in dm_bufio, dm_bufio_shrink_scan()
runs, mutex dm_bufio_client->lock is acquired, then P1 waits for dm_buffer
IO to complete in __try_evict_buffer().
But this IO may never complete if issued to an underlying loop device
that forwards it using direct-IO, which allocates memory using
GFP_KERNEL (see: do_blockdev_direct_IO()). If allocation fails, memory
reclaim will invoke memory shrinker in dm_bufio, dm_bufio_shrink_scan()
will be invoked, and since the mutex is already held by P1 the loop
thread will hang, and IO will never complete. Resulting in ABBA
deadlock.
Cc: stable@vger.kernel.org
Signed-off-by: Junxiao Bi <junxiao.bi@oracle.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 4aabed699c400810981d3dda170f05fa4d782905 upstream.
Allow up to four clocks to be specified and enabled for the orion-mdio
interface, which are required by the Armada 8k and defined in
armada-cp110.dtsi.
Fixes a hang in probing the mvmdio driver that was encountered on the
Clearfog GT 8K with all drivers built as modules, but also affects other
boards such as the MacchiatoBIN.
Cc: stable@vger.kernel.org
Fixes: 96cb43423822 ("net: mvmdio: allow up to three clocks to be specified for orion-mdio")
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Josua Mayer <josua@solid-run.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 5b933e28d8b1fbdc7fbac4bfc569f3b152c3dd59 upstream.
There is no audio_pll2_clk registered, it should be audio_pll2_out.
Cc: <stable@vger.kernel.org>
Fixes: ba5625c3e272 ("clk: imx: Add clock driver support for imx8mm")
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit e244c4699f859cf7149b0781b1894c7996a8a1df upstream.
With Link Power Management (LPM) enabled USB3 links transition to low
power U1/U2 link states from U0 state automatically.
Current hub code detects USB3 remote wakeups by checking if the software
state still shows suspended, but the link has transitioned from suspended
U3 to enabled U0 state.
As it takes some time before the hub thread reads the port link state
after a USB3 wake notification, the link may have transitioned from U0
to U1/U2, and wake is not detected by hub code.
Fix this by handling U1/U2 states in the same way as U0 in USB3 wakeup
handling
This patch should be added to stable kernels since 4.13 where LPM was
kept enabled during suspend/resume
Cc: <stable@vger.kernel.org> # v4.13+
Signed-off-by: Lee, Chiasheng <chiasheng.lee@intel.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 918b8646497b5dba6ae82d4a7325f01b258972b9 upstream.
Commit 4e0eaf239fb3 ("intel_th: msu: Fix single mode with IOMMU") switched
the single mode code to use dma mapping pages obtained from the page
allocator, but with IOMMU disabled, that may lead to using SWIOTLB bounce
buffers and without additional sync'ing, produces empty trace buffers.
Fix this by using a DMA32 GFP flag to the page allocation in single mode,
as the device supports full 32-bit DMA addressing.
Signed-off-by: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Fixes: 4e0eaf239fb3 ("intel_th: msu: Fix single mode with IOMMU")
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reported-by: Ammy Yi <ammy.yi@intel.com>
Cc: stable <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20190621161930.60785-4-alexander.shishkin@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit b83408b580eccf8d2797cd6cb9ae42c2a28656a7 upstream.
In case of the last page containing bitflips (ret > 0),
spinand_mtd_read() will return that number of bitflips for the last
page while it should instead return max_bitflips like it does when the
last page read returns with 0.
Signed-off-by: Weixiong Liao <liaoweixiong@allwinnertech.com>
Reviewed-by: Boris Brezillon <boris.brezillon@collabora.com>
Reviewed-by: Frieder Schrempf <frieder.schrempf@kontron.de>
Cc: stable@vger.kernel.org
Fixes: 7529df465248 ("mtd: nand: Add core infrastructure to support SPI NANDs")
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit e1884ffddacc0424d7e785e6f8087bd12f7196db upstream.
At present, the flow of calculating AC timing of read/write cycle in SDR
mode is that:
At first, calculate high hold time which is valid for both read and write
cycle using the max value between tREH_min and tWH_min.
Secondly, calculate WE# pulse width using tWP_min.
Thridly, calculate RE# pulse width using the bigger one between tREA_max
and tRP_min.
But NAND SPEC shows that Controller should also meet write/read cycle time.
That is write cycle time should be more than tWC_min and read cycle should
be more than tRC_min. Obviously, we do not achieve that now.
This patch corrects the low level time calculation to meet minimum
read/write cycle time required. After getting the high hold time, WE# low
level time will be promised to meet tWP_min and tWC_min requirement,
and RE# low level time will be promised to meet tREA_max, tRP_min and
tRC_min requirement.
Fixes: edfee3619c49 ("mtd: nand: mtk: add ->setup_data_interface() hook")
Cc: stable@vger.kernel.org # v4.17+
Signed-off-by: Xiaolei Li <xiaolei.li@mediatek.com>
Reviewed-by: Miquel Raynal <miquel.raynal@bootlin.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 5e6b6651d22de109ebf48ca00d0373bc2c0cc080 upstream.
mutexes can sleep and therefore should not be taken while holding a
spinlock. move clk_get_rate (can sleep) outside the spinlock protected
region.
Fixes: 83736352e0ca ("mmc: sdhci-msm: Update DLL reset sequence")
Cc: stable@vger.kernel.org
Signed-off-by: Jorge Ramirez-Ortiz <jorge.ramirez-ortiz@linaro.org>
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Reviewed-by: Vinod Koul <vkoul@kernel.org>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 3d1f62c686acdedf5ed9642b763f3808d6a47d1e upstream.
The saturation bit was being set at bit 9 in the second 32-bit word
of the TPMEM CSC. This isn't correct, the saturation bit is bit 42,
which is bit 10 of the second word.
Fixes: 1aa8ea0d2bd5d ("gpu: ipu-v3: Add Image Converter unit")
Signed-off-by: Steve Longerbeam <slongerbeam@gmail.com>
Reviewed-by: Philipp Zabel <p.zabel@pengutronix.de>
Cc: stable@vger.kernel.org
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 7e3e888dfc138089f4c15a81b418e88f0978f744 upstream.
At namespace creation time there is the potential for the "expected to
be zero" fields of a 'pfn' info-block to be filled with indeterminate
data. While the kernel buffer is zeroed on allocation it is immediately
overwritten by nd_pfn_validate() filling it with the current contents of
the on-media info-block location. For fields like, 'flags' and the
'padding' it potentially means that future implementations can not rely on
those fields being zero.
In preparation to stop using the 'start_pad' and 'end_trunc' fields for
section alignment, arrange for fields that are not explicitly
initialized to be guaranteed zero. Bump the minor version to indicate
it is safe to assume the 'padding' and 'flags' are zero. Otherwise,
this corruption is expected to benign since all other critical fields
are explicitly initialized.
Note The cc: stable is about spreading this new policy to as many
kernels as possible not fixing an issue in those kernels. It is not
until the change titled "libnvdimm/pfn: Stop padding pmem namespaces to
section alignment" where this improper initialization becomes a problem.
So if someone decides to backport "libnvdimm/pfn: Stop padding pmem
namespaces to section alignment" (which is not tagged for stable), make
sure this pre-requisite is flagged.
Link: http://lkml.kernel.org/r/156092356065.979959.6681003754765958296.stgit@dwillia2-desk3.amr.corp.intel.com
Fixes: 32ab0a3f5170 ("libnvdimm, pmem: 'struct page' for pmem")
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Tested-by: Aneesh Kumar K.V <aneesh.kumar@linux.ibm.com> [ppc64]
Cc: <stable@vger.kernel.org>
Cc: David Hildenbrand <david@redhat.com>
Cc: Jane Chu <jane.chu@oracle.com>
Cc: Jeff Moyer <jmoyer@redhat.com>
Cc: Jérôme Glisse <jglisse@redhat.com>
Cc: Jonathan Corbet <corbet@lwn.net>
Cc: Logan Gunthorpe <logang@deltatee.com>
Cc: Michal Hocko <mhocko@suse.com>
Cc: Mike Rapoport <rppt@linux.ibm.com>
Cc: Oscar Salvador <osalvador@suse.de>
Cc: Pavel Tatashin <pasha.tatashin@soleen.com>
Cc: Toshi Kani <toshi.kani@hpe.com>
Cc: Vlastimil Babka <vbabka@suse.cz>
Cc: Wei Yang <richardw.yang@linux.intel.com>
Cc: Jason Gunthorpe <jgg@mellanox.com>
Cc: Christoph Hellwig <hch@lst.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 68c20cc2164cc5c7c73f8012ae6491afdb1f7f72 upstream.
This affects the 2nd-gen Intuos Pro Medium and Large
when using their Bluetooth connection.
Fixes: 4922cd26f03c ("HID: wacom: Support 2nd-gen Intuos Pro's Bluetooth classic interface")
Cc: <stable@vger.kernel.org> # v4.11+
Signed-off-by: Aaron Armstrong Skomra <aaron.skomra@wacom.com>
Reviewed-by: Jason Gerecke <jason.gerecke@wacom.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit d4b8efeb46d99a5d02e7f88ac4eaccbe49370770 upstream.
Only sync the pad once per report, not once per collection.
Also avoid syncing the pad on battery reports.
Fixes: f8b6a74719b5 ("HID: wacom: generic: Support multiple tools per report")
Cc: <stable@vger.kernel.org> # v4.17+
Signed-off-by: Aaron Armstrong Skomra <aaron.skomra@wacom.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit d8e9806005f28bbb49899dab2068e3359e22ba35 upstream.
Currently, the driver will attempt to set the mode on all
devices with a center button, but some devices with a center
button lack LEDs, and attempting to set the LEDs on devices
without LEDs results in the kernel error message of the form:
"leds input8::wacom-0.1: Setting an LED's brightness failed (-32)"
This is because the generic codepath erroneously assumes that the
BUTTON_CENTER usage indicates that the device has LEDs, the
previously ignored TOUCH_RING_SETTING usage is a more accurate
indication of the existence of LEDs on the device.
Fixes: 10c55cacb8b2 ("HID: wacom: generic: support LEDs")
Cc: <stable@vger.kernel.org> # v4.11+
Signed-off-by: Aaron Armstrong Skomra <aaron.skomra@wacom.com>
Reviewed-by: Jason Gerecke <jason.gerecke@wacom.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 89705e92700170888236555fe91b45e4c1bb0985 upstream.
Userspace expects the IB_TM_CAP_RC bit to indicate that the device
supports RC transport tag matching with rendezvous offload. However the
firmware splits this into two capabilities for eager and rendezvous tag
matching.
Only if the FW supports both modes should userspace be told the tag
matching capability is available.
Cc: <stable@vger.kernel.org> # 4.13
Fixes: eb761894351d ("IB/mlx5: Fill XRQ capabilities")
Signed-off-by: Danit Goldberg <danitg@mellanox.com>
Reviewed-by: Yishai Hadas <yishaih@mellanox.com>
Reviewed-by: Artemy Kovalyov <artemyko@mellanox.com>
Signed-off-by: Leon Romanovsky <leonro@mellanox.com>
Signed-off-by: Jason Gunthorpe <jgg@mellanox.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 64adde31c8e996a6db6f7a1a4131180e363aa9f2 upstream.
Currently, there is only a 1 ms sleep after asserting PERST.
Reading the datasheets for different endpoints, some require PERST to be
asserted for 10 ms in order for the endpoint to perform a reset, others
require it to be asserted for 50 ms.
Several SoCs using this driver uses PCIe Mini Card, where we don't know
what endpoint will be plugged in.
The PCI Express Card Electromechanical Specification r2.0, section
2.2, "PERST# Signal" specifies:
"On power up, the deassertion of PERST# is delayed 100 ms (TPVPERL) from
the power rails achieving specified operating limits."
Add a sleep of 100 ms before deasserting PERST, in order to ensure that
we are compliant with the spec.
Fixes: 82a823833f4e ("PCI: qcom: Add Qualcomm PCIe controller driver")
Signed-off-by: Niklas Cassel <niklas.cassel@linaro.org>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Acked-by: Stanimir Varbanov <svarbanov@mm-sol.com>
Cc: stable@vger.kernel.org # 4.5+
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 000dd5316e1c756a1c028f22e01d06a38249dd4d upstream.
PME polling does not take into account that a device that is directly
connected to the host bridge may go into D3cold as well. This leads to a
situation where the PME poll thread reads from a config space of a
device that is in D3cold and gets incorrect information because the
config space is not accessible.
Here is an example from Intel Ice Lake system where two PCIe root ports
are in D3cold (I've instrumented the kernel to log the PMCSR register
contents):
[ 62.971442] pcieport 0000:00:07.1: Check PME status, PMCSR=0xffff
[ 62.971504] pcieport 0000:00:07.0: Check PME status, PMCSR=0xffff
Since 0xffff is interpreted so that PME is pending, the root ports will
be runtime resumed. This repeats over and over again essentially
blocking all runtime power management.
Prevent this from happening by checking whether the device is in D3cold
before its PME status is read.
Fixes: 71a83bd727cc ("PCI/PM: add runtime PM support to PCIe port")
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Reviewed-by: Lukas Wunner <lukas@wunner.de>
Cc: 3.6+ <stable@vger.kernel.org> # v3.6+
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 4df591b20b80cb77920953812d894db259d85bd7 upstream.
Fix a use-after-free in hv_eject_device_work().
Fixes: 05f151a73ec2 ("PCI: hv: Fix a memory leak in hv_eject_device_work()")
Signed-off-by: Dexuan Cui <decui@microsoft.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Michael Kelley <mikelley@microsoft.com>
Cc: stable@vger.kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 4aa5aed2b6f267592705a526f57518a5d715b769 upstream.
This adds Ice Lake NNPI support to the Intel(R) Trace Hub.
Signed-off-by: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Cc: stable <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20190621161930.60785-5-alexander.shishkin@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit bcef5b7215681250c4bf8961dfe15e9e4fef97d0 upstream.
The function srp_parse_in() is used both for parsing source address
specifications and for target address specifications. Target addresses
must have a port number. Having to specify a port number for source
addresses is inconvenient. Make sure that srp_parse_in() supports again
parsing addresses with no port number.
Cc: <stable@vger.kernel.org>
Fixes: c62adb7def71 ("IB/srp: Fix IPv6 address parsing")
Signed-off-by: Bart Van Assche <bvanassche@acm.org>
Signed-off-by: Jason Gunthorpe <jgg@mellanox.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit e28ad544f462231d3fd081a7316339359efbb481 upstream.
DisplayID blocks allow embedding of CEA blocks. The payloads are
identical to traditional top level CEA extension blocks, but the header
is slightly different.
This change allows the CEA parser to find a CEA block inside a DisplayID
block. Additionally, it adds support for parsing the embedded CTA
header. No further changes are necessary due to payload parity.
This change fixes audio support for the Valve Index HMD.
Signed-off-by: Andres Rodriguez <andresx7@gmail.com>
Reviewed-by: Dave Airlie <airlied@redhat.com>
Cc: Jani Nikula <jani.nikula@linux.intel.com>
Cc: <stable@vger.kernel.org> # v4.15
Signed-off-by: Dave Airlie <airlied@redhat.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190619180901.17901-1-andresx7@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 41a531ffa4c5aeb062f892227c00fabb3b4a9c91 upstream.
Since commit ed194d136769 ("usb: core: remove local_irq_save() around
->complete() handler") the handler rt2x00usb_interrupt_rxdone() is
not running with interrupts disabled anymore. So this completion handler
is not guaranteed to run completely before workqueue processing starts
for the same queue entry.
Be sure to set all other flags in the entry correctly before marking
this entry ready for workqueue processing. This way we cannot miss error
conditions that need to be signalled from the completion handler to the
worker thread.
Note that rt2x00usb_work_rxdone() processes all available entries, not
only such for which queue_work() was called.
This patch is similar to what commit df71c9cfceea ("rt2x00: fix order
of entry flags modification") did for TX processing.
This fixes a regression on a RT5370 based wifi stick in AP mode, which
suddenly stopped data transmission after some period of heavy load. Also
stopping the hanging hostapd resulted in the error message "ieee80211
phy0: rt2x00queue_flush_queue: Warning - Queue 14 failed to flush".
Other operation modes are probably affected as well, this just was
the used testcase.
Fixes: ed194d136769 ("usb: core: remove local_irq_save() around ->complete() handler")
Cc: stable@vger.kernel.org # 4.20+
Signed-off-by: Soeren Moch <smoch@web.de>
Acked-by: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit bce5963bcb4f9934faa52be323994511d59fd13c upstream.
When binding an interdomain event channel to a vcpu via
IOCTL_EVTCHN_BIND_INTERDOMAIN not only the event channel needs to be
bound, but the affinity of the associated IRQi must be changed, too.
Otherwise the IRQ and the event channel won't be moved to another vcpu
in case the original vcpu they were bound to is going offline.
Cc: <stable@vger.kernel.org> # 4.13
Fixes: c48f64ab472389df ("xen-evtchn: Bind dyn evtchn:qemu-dm interrupt to next online VCPU")
Signed-off-by: Juergen Gross <jgross@suse.com>
Reviewed-by: Boris Ostrovsky <boris.ostrovsky@oracle.com>
Signed-off-by: Juergen Gross <jgross@suse.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 3b8cafdd5436f9298b3bf6eb831df5eef5ee82b6 upstream.
dm-zoned uses the zone flag DMZ_ACTIVE to indicate that a zone of the
backend device is being actively read or written and so cannot be
reclaimed. This flag is set as long as the zone atomic reference
counter is not 0. When this atomic is decremented and reaches 0 (e.g.
on BIO completion), the active flag is cleared and set again whenever
the zone is reused and BIO issued with the atomic counter incremented.
These 2 operations (atomic inc/dec and flag set/clear) are however not
always executed atomically under the target metadata mutex lock and
this causes the warning:
WARN_ON(!test_bit(DMZ_ACTIVE, &zone->flags));
in dmz_deactivate_zone() to be displayed. This problem is regularly
triggered with xfstests generic/209, generic/300, generic/451 and
xfs/077 with XFS being used as the file system on the dm-zoned target
device. Similarly, xfstests ext4/303, ext4/304, generic/209 and
generic/300 trigger the warning with ext4 use.
This problem can be easily fixed by simply removing the DMZ_ACTIVE flag
and managing the "ACTIVE" state by directly looking at the reference
counter value. To do so, the functions dmz_activate_zone() and
dmz_deactivate_zone() are changed to inline functions respectively
calling atomic_inc() and atomic_dec(), while the dmz_is_active() macro
is changed to an inline function calling atomic_read().
Fixes: 3b1a94c88b79 ("dm zoned: drive-managed zoned block device target")
Cc: stable@vger.kernel.org
Reported-by: Masato Suzuki <masato.suzuki@wdc.com>
Signed-off-by: Damien Le Moal <damien.lemoal@wdc.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 7cb95eeea6706c790571042a06782e378b2561ea upstream.
It turns out that while disabling i2c bus access from software when the
GPU is suspended was a step in the right direction with:
commit 342406e4fbba ("drm/nouveau/i2c: Disable i2c bus access after
->fini()")
We also ended up accidentally breaking the vbios init scripts on some
older Tesla GPUs, as apparently said scripts can actually use the i2c
bus. Since these scripts are executed before initializing any
subdevices, we end up failing to acquire access to the i2c bus which has
left a number of cards with their fan controllers uninitialized. Luckily
this doesn't break hardware - it just means the fan gets stuck at 100%.
This also means that we've always been using our i2c busses before
initializing them during the init scripts for older GPUs, we just didn't
notice it until we started preventing them from being used until init.
It's pretty impressive this never caused us any issues before!
So, fix this by initializing our i2c pad and busses during subdev
pre-init. We skip initializing aux busses during pre-init, as those are
guaranteed to only ever be used by nouveau for DP aux transactions.
Signed-off-by: Lyude Paul <lyude@redhat.com>
Tested-by: Marc Meledandri <m.meledandri@gmail.com>
Fixes: 342406e4fbba ("drm/nouveau/i2c: Disable i2c bus access after ->fini()")
Cc: stable@vger.kernel.org
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit ecc8fb54bd443bf69996d9d5ddb8d90a50f14936 upstream.
Currently the I3C framework limits SCL frequency to FM speed when
dealing with a mixed slow bus, even if all I2C devices are FM+ capable.
The core was also not accounting for I3C speed limitations when
operating in mixed slow mode and was erroneously using FM+ speed as the
max I2C speed when operating in mixed fast mode.
Fixes: 3a379bbcea0a ("i3c: Add core I3C infrastructure")
Signed-off-by: Vitor Soares <vitor.soares@synopsys.com>
Cc: Boris Brezillon <bbrezillon@kernel.org>
Cc: <stable@vger.kernel.org>
Cc: <linux-kernel@vger.kernel.org>
Signed-off-by: Boris Brezillon <boris.brezillon@collabora.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 70f1b0d34bdf03065fe869e93cc17cad1ea20c4a upstream.
The usb support for asyncio encoded one of it's values in the wrong
field. It should have used si_value but instead used si_addr which is
not present in the _rt union member of struct siginfo.
The practical result of this is that on a 64bit big endian kernel
when delivering a signal to a 32bit process the si_addr field
is set to NULL, instead of the expected pointer value.
This issue can not be fixed in copy_siginfo_to_user32 as the usb
usage of the the _sigfault (aka si_addr) member of the siginfo
union when SI_ASYNCIO is set is incompatible with the POSIX and
glibc usage of the _rt member of the siginfo union.
Therefore replace kill_pid_info_as_cred with kill_pid_usb_asyncio a
dedicated function for this one specific case. There are no other
users of kill_pid_info_as_cred so this specialization should have no
impact on the amount of code in the kernel. Have kill_pid_usb_asyncio
take instead of a siginfo_t which is difficult and error prone, 3
arguments, a signal number, an errno value, and an address enconded as
a sigval_t. The encoding of the address as a sigval_t allows the
code that reads the userspace request for a signal to handle this
compat issue along with all of the other compat issues.
Add BUILD_BUG_ONs in kernel/signal.c to ensure that we can now place
the pointer value at the in si_pid (instead of si_addr). That is the
code now verifies that si_pid and si_addr always occur at the same
location. Further the code veries that for native structures a value
placed in si_pid and spilling into si_uid will appear in userspace in
si_addr (on a byte by byte copy of siginfo or a field by field copy of
siginfo). The code also verifies that for a 64bit kernel and a 32bit
userspace the 32bit pointer will fit in si_pid.
I have used the usbsig.c program below written by Alan Stern and
slightly tweaked by me to run on a big endian machine to verify the
issue exists (on sparc64) and to confirm the patch below fixes the issue.
/* usbsig.c -- test USB async signal delivery */
#define _GNU_SOURCE
#include <stdio.h>
#include <fcntl.h>
#include <signal.h>
#include <string.h>
#include <sys/ioctl.h>
#include <unistd.h>
#include <endian.h>
#include <linux/usb/ch9.h>
#include <linux/usbdevice_fs.h>
static struct usbdevfs_urb urb;
static struct usbdevfs_disconnectsignal ds;
static volatile sig_atomic_t done = 0;
void urb_handler(int sig, siginfo_t *info , void *ucontext)
{
printf("Got signal %d, signo %d errno %d code %d addr: %p urb: %p\n",
sig, info->si_signo, info->si_errno, info->si_code,
info->si_addr, &urb);
printf("%s\n", (info->si_addr == &urb) ? "Good" : "Bad");
}
void ds_handler(int sig, siginfo_t *info , void *ucontext)
{
printf("Got signal %d, signo %d errno %d code %d addr: %p ds: %p\n",
sig, info->si_signo, info->si_errno, info->si_code,
info->si_addr, &ds);
printf("%s\n", (info->si_addr == &ds) ? "Good" : "Bad");
done = 1;
}
int main(int argc, char **argv)
{
char *devfilename;
int fd;
int rc;
struct sigaction act;
struct usb_ctrlrequest *req;
void *ptr;
char buf[80];
if (argc != 2) {
fprintf(stderr, "Usage: usbsig device-file-name\n");
return 1;
}
devfilename = argv[1];
fd = open(devfilename, O_RDWR);
if (fd == -1) {
perror("Error opening device file");
return 1;
}
act.sa_sigaction = urb_handler;
sigemptyset(&act.sa_mask);
act.sa_flags = SA_SIGINFO;
rc = sigaction(SIGUSR1, &act, NULL);
if (rc == -1) {
perror("Error in sigaction");
return 1;
}
act.sa_sigaction = ds_handler;
sigemptyset(&act.sa_mask);
act.sa_flags = SA_SIGINFO;
rc = sigaction(SIGUSR2, &act, NULL);
if (rc == -1) {
perror("Error in sigaction");
return 1;
}
memset(&urb, 0, sizeof(urb));
urb.type = USBDEVFS_URB_TYPE_CONTROL;
urb.endpoint = USB_DIR_IN | 0;
urb.buffer = buf;
urb.buffer_length = sizeof(buf);
urb.signr = SIGUSR1;
req = (struct usb_ctrlrequest *) buf;
req->bRequestType = USB_DIR_IN | USB_TYPE_STANDARD | USB_RECIP_DEVICE;
req->bRequest = USB_REQ_GET_DESCRIPTOR;
req->wValue = htole16(USB_DT_DEVICE << 8);
req->wIndex = htole16(0);
req->wLength = htole16(sizeof(buf) - sizeof(*req));
rc = ioctl(fd, USBDEVFS_SUBMITURB, &urb);
if (rc == -1) {
perror("Error in SUBMITURB ioctl");
return 1;
}
rc = ioctl(fd, USBDEVFS_REAPURB, &ptr);
if (rc == -1) {
perror("Error in REAPURB ioctl");
return 1;
}
memset(&ds, 0, sizeof(ds));
ds.signr = SIGUSR2;
ds.context = &ds;
rc = ioctl(fd, USBDEVFS_DISCSIGNAL, &ds);
if (rc == -1) {
perror("Error in DISCSIGNAL ioctl");
return 1;
}
printf("Waiting for usb disconnect\n");
while (!done) {
sleep(1);
}
close(fd);
return 0;
}
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: linux-usb@vger.kernel.org
Cc: Alan Stern <stern@rowland.harvard.edu>
Cc: Oliver Neukum <oneukum@suse.com>
Fixes: v2.3.39
Cc: stable@vger.kernel.org
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 14f28f5cea9e3998442de87846d1907a531b6748 upstream.
buf->size is an unsigned long; casting that to int will lead to an
overflow if buf->size exceeds INT_MAX.
Fix this by changing the type to unsigned long instead. This is possible
as the buf->size is always aligned to PAGE_SIZE, and therefore the size
will never have values lesser than 0.
Note on backporting to stable: the file used to be under
drivers/media/v4l2-core, it was moved to the current location after 4.14.
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Cc: stable@vger.kernel.org
Reviewed-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit defcdc5d89ced780fb45196d539d6570ec5b1ba5 upstream.
PAGE_ALIGN() may wrap the buffer size around to 0. Prevent this by
checking that the aligned value is not smaller than the unaligned one.
Note on backporting to stable: the file used to be under
drivers/media/v4l2-core, it was moved to the current location after 4.14.
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Cc: stable@vger.kernel.org
Reviewed-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
