| Age | Commit message (Collapse) | Author |
|---|
|
[ Upstream commit 49ce881c0d4c4a7a35358d9dccd5f26d0e56fc61 ]
Commit 984203ceff27 ("net: stmmac: mdio: remove reset gpio free")
removed the reset gpio free, when the driver is unbinded or rmmod,
we miss the gpio free.
This patch uses managed API to request the reset gpio, so that the
gpio could be freed properly.
Fixes: 984203ceff27 ("net: stmmac: mdio: remove reset gpio free")
Signed-off-by: Jisheng Zhang <Jisheng.Zhang@synaptics.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit 3d3ced2ec5d71b99d72ae6910fbdf890bc2eccf0 ]
Some boards do not have the PHY firmware programmed in the 3310's flash,
which leads to the PHY not working as expected. Warn the user when the
PHY fails to boot the firmware and refuse to initialise.
Fixes: 20b2af32ff3f ("net: phy: add Marvell Alaska X 88X3310 10Gigabit PHY support")
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Tested-by: Maxime Chevallier <maxime.chevallier@bootlin.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit 21808437214637952b61beaba6034d97880fbeb3 ]
MVPP2_TXQ_SCHED_TOKEN_CNTR_REG() expects the logical queue id but
the current code is passing the global tx queue offset, so it ends
up writing to unknown registers (between 0x8280 and 0x82fc, which
seemed to be unused by the hardware). This fixes the issue by using
the logical queue id instead.
Fixes: 3f518509dedc ("ethernet: Add new driver for Marvell Armada 375 network unit")
Signed-off-by: Antoine Tenart <antoine.tenart@bootlin.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit d484e06e25ebb937d841dac02ac1fe76ec7d4ddd ]
Fix below issues in err code path of probe:
1. we don't need to unregister_netdev() because the netdev isn't
registered.
2. when register_netdev() fails, we also need to destroy bm pool for
HWBM case.
Fixes: dc35a10f68d3 ("net: mvneta: bm: add support for hardware buffer management")
Signed-off-by: Jisheng Zhang <Jisheng.Zhang@synaptics.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit ce8d24f9a5965a58c588f9342689702a1024433c ]
Fix the clk mismatch in the error path "failed_reset" because
below error path will disable clk_ahb and clk_ipg directly, it
should use pm_runtime_put_noidle() instead of pm_runtime_put()
to avoid to call runtime resume callback.
Reported-by: Baruch Siach <baruch@tkos.co.il>
Signed-off-by: Fugang Duan <fugang.duan@nxp.com>
Tested-by: Baruch Siach <baruch@tkos.co.il>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit 84b3fd1fc9592d431e23b077e692fa4e3fd0f086 ]
Currently, the upper half of a 4-byte STATS_TYPE_PORT statistic ends
up in bits 47:32 of the return value, instead of bits 31:16 as they
should.
Fixes: 6e46e2d821bb ("net: dsa: mv88e6xxx: Fix u64 statistics")
Signed-off-by: Rasmus Villemoes <rasmus.villemoes@prevas.dk>
Reviewed-by: Vivien Didelot <vivien.didelot@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit ef74422020aa8c224b00a927e3e47faac4d8fae3 ]
When identical rules are inserted, the latter one goes to C-TCAM. For
that, a second eRP with the same mask is created. These 2 eRPs by the
nature cannot be merged and also one cannot be parent of another.
Teach mlxsw_sp_acl_erp_delta_fill() about this possibility and handle it
gracefully.
Reported-by: Alex Kushnarov <alexanderk@mellanox.com>
Fixes: c22291f7cf45 ("mlxsw: spectrum: acl: Implement delta for ERP")
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit b5730061d1056abf317caea823b94d6e12b5b4f6 ]
VLAN flows never get offloaded unless ivlan_vld is set in filter spec.
It's not compulsory for vlan_ethtype to be set.
So, always enable ivlan_vld bit for offloading VLAN flows regardless of
vlan_ethtype is set or not.
Fixes: ad9af3e09c (cxgb4: add tc flower match support for vlan)
Signed-off-by: Raju Rangoju <rajur@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit 334031219a84b9994594015aab85ed7754c80176 ]
Once in a while, with just the right timing, 802.3ad slaves will fail to
properly initialize, winding up in a weird state, with a partner system
mac address of 00:00:00:00:00:00. This started happening after a fix to
properly track link_failure_count tracking, where an 802.3ad slave that
reported itself as link up in the miimon code, but wasn't able to get a
valid speed/duplex, started getting set to BOND_LINK_FAIL instead of
BOND_LINK_DOWN. That was the proper thing to do for the general "my link
went down" case, but has created a link initialization race that can put
the interface in this odd state.
The simple fix is to instead set the slave link to BOND_LINK_DOWN again,
if the link has never been up (last_link_up == 0), so the link state
doesn't bounce from BOND_LINK_DOWN to BOND_LINK_FAIL -- it hasn't failed
in this case, it simply hasn't been up yet, and this prevents the
unnecessary state change from DOWN to FAIL and getting stuck in an init
failure w/o a partner mac.
Fixes: ea53abfab960 ("bonding/802.3ad: fix link_failure_count tracking")
CC: Jay Vosburgh <j.vosburgh@gmail.com>
CC: Veaceslav Falico <vfalico@gmail.com>
CC: Andy Gospodarek <andy@greyhouse.net>
CC: "David S. Miller" <davem@davemloft.net>
CC: netdev@vger.kernel.org
Tested-by: Heesoon Kim <Heesoon.Kim@stratus.com>
Signed-off-by: Jarod Wilson <jarod@redhat.com>
Acked-by: Jay Vosburgh <jay.vosburgh@canonical.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit efa31801203ac2f5c6a82a28cb991c7163ee0f1d ]
The Allwinner BSP makes sure that we don't end up with a null start delay
or with a delay larger than vtotal.
The former condition is likely to happen now with the reworked start delay,
so make sure we enforce the same boundaries.
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Reviewed-by: Paul Kocialkowski <paul.kocialkowski@bootlin.com>
Link: https://patchwork.freedesktop.org/patch/msgid/c9889cf5f7a3d101ef380905900b45a182596f56.1549896081.git-series.maxime.ripard@bootlin.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 5abac9d7e1bb9a373673811154774d4c89a7f85e ]
Currently we check if the __ICE_PREPARED_FOR_RESET bit is set prior to
calling ice_prepare_for_reset in ice_reset_subtask(), but we aren't
checking that bit in ice_do_reset() before calling
ice_prepare_for_reset(). This is not consistent and can cause issues if
ice_prepare_for_reset() is called prior to ice_do_reset(). Fix this by
checking if the __ICE_PREPARED_FOR_RESET bit is set internal to
ice_prepare_for_reset().
Signed-off-by: Brett Creeley <brett.creeley@intel.com>
Signed-off-by: Anirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit d1ffa760d22aa1d8190478e5ef555c59a771db27 ]
The quiesce function calls cio_cancel_halt_clear() and if we
get an -EBUSY we go into a loop where we:
- wait for any interrupts
- flush all I/O in the workqueue
- retry cio_cancel_halt_clear
During the period where we are waiting for interrupts or
flushing all I/O, the channel subsystem could have completed
a halt/clear action and turned off the corresponding activity
control bits in the subchannel status word. This means the next
time we call cio_cancel_halt_clear(), we will again start by
calling cancel subchannel and so we can be stuck between calling
cancel and halt forever.
Rather than calling cio_cancel_halt_clear() immediately after
waiting, let's try to disable the subchannel. If we succeed in
disabling the subchannel then we know nothing else can happen
with the device.
Suggested-by: Eric Farman <farman@linux.ibm.com>
Signed-off-by: Farhan Ali <alifm@linux.ibm.com>
Message-Id: <4d5a4b98ab1b41ac6131b5c36de18b76c5d66898.1555449329.git.alifm@linux.ibm.com>
Reviewed-by: Eric Farman <farman@linux.ibm.com>
Acked-by: Halil Pasic <pasic@linux.ibm.com>
Signed-off-by: Cornelia Huck <cohuck@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit da676c6aa6413d59ab0a80c97bbc273025e640b2 ]
The current calculation for the video start delay in the current DSI driver
is that it is the total vertical size, minus the front porch and sync length,
plus 1. This equals to the active vertical size plus the back porch plus 1.
That 1 is coming in the Allwinner BSP from an variable that is set to 1.
However, if we look at the Allwinner BSP more closely, and especially in
the "legacy" code for the display (in drivers/video/sunxi/legacy/), we can
see that this variable is actually computed from the porches and the sync
minus 10, clamped between 8 and 100.
This fixes the start delay symptom we've seen on some panels (vblank
timeouts with vertical white stripes at the bottom of the panel).
Reviewed-by: Paul Kocialkowski <paul.kocialkowski@bootlin.com>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Link: https://patchwork.freedesktop.org/patch/msgid/6e5f72e68f47ca0223877464bf12f0c3f3978de8.1549896081.git-series.maxime.ripard@bootlin.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 60b801999c48b6c1dd04e653a38e2e613664264e ]
After an event is sent, we try to copy it into the user buffer of the
first waiter in drm_read() and if the user buffer doesn't have enough
room we put it back onto the list. However, we didn't wake up any
subsequent waiter, so that event may sit on the list until either a new
vblank event is sent or a new waiter appears. Rare, but in the worst
case may lead to a stuck process.
Testcase: igt/drm_read/short-buffer-wakeup
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20170804082328.17173-1-chris@chris-wilson.co.uk
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 56be6503aab2bc3a30beae408071b9be5e1bae51 ]
This makes it safe to access drm_device->dev after the parent device has
been removed/unplugged.
Signed-off-by: Noralf Trønnes <noralf@tronnes.org>
Reviewed-by: Gerd Hoffmann <kraxel@redhat.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190225144232.20761-2-noralf@tronnes.org
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit fc22771547e7e8a63679f0218e943d72b107de65 ]
Noted in review by Dave Emett for V3D 4.2 support.
Signed-off-by: Eric Anholt <eric@anholt.net>
Link: https://patchwork.freedesktop.org/patch/msgid/20190308174336.7866-1-eric@anholt.net
Reviewed-by: Dave Emett <david.emett@broadcom.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 5442dcaa0d90fc376bdfc179a018931a8f43dea4 ]
This fixes a bug for messages containing both zero length and
unidirectional xfers.
The function spi_map_msg will allocate dummy tx and/or rx buffers
for use with unidirectional transfers when the hardware can only do
a bidirectional transfer. That dummy buffer will be used in place
of a NULL buffer even when the xfer length is 0.
Then in the function __spi_map_msg, if he hardware can dma,
the zero length xfer will have spi_map_buf called on the dummy
buffer.
Eventually, __sg_alloc_table is called and returns -EINVAL
because nents == 0.
This fix prevents the error by not using the dummy buffer when
the xfer length is zero.
Signed-off-by: Chris Lesiak <chris.lesiak@licor.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 5e6afb3832bedf420dd8e4c5b32ed85117c5087d ]
The mutex for the regulator_dev must be controlled by the caller of
the regulator_notifier_call_chain(), as described in the comment
for that function.
Failure to mutex lock and unlock surrounding the notifier call results
in a kernel WARN_ON_ONCE() which will dump a backtrace for the
regulator_notifier_call_chain() when that function call is first made.
The mutex can be controlled using the regulator_lock/unlock() API.
Fixes: f6130be652d0 ("regulator: DA9055 regulator driver")
Suggested-by: Adam Thomson <Adam.Thomson.Opensource@diasemi.com>
Signed-off-by: Steve Twiss <stwiss.opensource@diasemi.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 978995def0f6030aa6b3b494682f673aca13881b ]
The mutex for the regulator_dev must be controlled by the caller of
the regulator_notifier_call_chain(), as described in the comment
for that function.
Failure to mutex lock and unlock surrounding the notifier call results
in a kernel WARN_ON_ONCE() which will dump a backtrace for the
regulator_notifier_call_chain() when that function call is first made.
The mutex can be controlled using the regulator_lock/unlock() API.
Fixes: 4068e5182ada ("regulator: da9062: DA9062 regulator driver")
Suggested-by: Adam Thomson <Adam.Thomson.Opensource@diasemi.com>
Signed-off-by: Steve Twiss <stwiss.opensource@diasemi.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 275513b7695a61b75b2546406ecd0f8e3d9fc8be ]
The mutex for the regulator_dev must be controlled by the caller of
the regulator_notifier_call_chain(), as described in the comment
for that function.
Failure to mutex lock and unlock surrounding the notifier call results
in a kernel WARN_ON_ONCE() which will dump a backtrace for the
regulator_notifier_call_chain() when that function call is first made.
The mutex can be controlled using the regulator_lock/unlock() API.
Fixes: c90456e36d9c ("regulator: pv88090: new regulator driver")
Suggested-by: Adam Thomson <Adam.Thomson.Opensource@diasemi.com>
Signed-off-by: Steve Twiss <stwiss.opensource@diasemi.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 119c4f5085c45b60cb23c5595e45d06135b89518 ]
The mutex for the regulator_dev must be controlled by the caller of
the regulator_notifier_call_chain(), as described in the comment
for that function.
Failure to mutex lock and unlock surrounding the notifier call results
in a kernel WARN_ON_ONCE() which will dump a backtrace for the
regulator_notifier_call_chain() when that function call is first made.
The mutex can be controlled using the regulator_lock/unlock() API.
Fixes: e4ee831f949a ("regulator: Add WM831x DC-DC buck convertor support")
Suggested-by: Adam Thomson <Adam.Thomson.Opensource@diasemi.com>
Signed-off-by: Steve Twiss <stwiss.opensource@diasemi.com>
Acked-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 1867af94cfdf37fc70fe67b3d522e78352800196 ]
The mutex for the regulator_dev must be controlled by the caller of
the regulator_notifier_call_chain(), as described in the comment
for that function.
Failure to mutex lock and unlock surrounding the notifier call results
in a kernel WARN_ON_ONCE() which will dump a backtrace for the
regulator_notifier_call_chain() when that function call is first made.
The mutex can be controlled using the regulator_lock/unlock() API.
Fixes: 99cf3af5e2d5 ("regulator: pv88080: new regulator driver")
Suggested-by: Adam Thomson <Adam.Thomson.Opensource@diasemi.com>
Signed-off-by: Steve Twiss <stwiss.opensource@diasemi.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 29d40b4a5776ec4727c9f0e00a884423dd5e3366 ]
The mutex for the regulator_dev must be controlled by the caller of
the regulator_notifier_call_chain(), as described in the comment
for that function.
Failure to mutex lock and unlock surrounding the notifier call results
in a kernel WARN_ON_ONCE() which will dump a backtrace for the
regulator_notifier_call_chain() when that function call is first made.
The mutex can be controlled using the regulator_lock/unlock() API.
Fixes: 69ca3e58d178 ("regulator: da9063: Add Dialog DA9063 voltage regulators support.")
Suggested-by: Adam Thomson <Adam.Thomson.Opensource@diasemi.com>
Signed-off-by: Steve Twiss <stwiss.opensource@diasemi.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 65378de3359d30ebce44762d8b8027f372b5b1c4 ]
The mutex for the regulator_dev must be controlled by the caller of
the regulator_notifier_call_chain(), as described in the comment
for that function.
Failure to mutex lock and unlock surrounding the notifier call results
in a kernel WARN_ON_ONCE() which will dump a backtrace for the
regulator_notifier_call_chain() when that function call is first made.
The mutex can be controlled using the regulator_lock/unlock() API.
Fixes: 1028a37daa14 ("regulator: da9211: new regulator driver")
Suggested-by: Adam Thomson <Adam.Thomson.Opensource@diasemi.com>
Signed-off-by: Steve Twiss <stwiss.opensource@diasemi.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 89b2758c192c35068b07766a6830433bfbdc1f44 ]
The mutex for the regulator_dev must be controlled by the caller of
the regulator_notifier_call_chain(), as described in the comment
for that function.
Failure to mutex lock and unlock surrounding the notifier call results
in a kernel WARN_ON_ONCE() which will dump a backtrace for the
regulator_notifier_call_chain() when that function call is first made.
The mutex can be controlled using the regulator_lock/unlock() API.
Fixes: b59320cc5a5e ("regulator: lp8755: new driver for LP8755")
Suggested-by: Adam Thomson <Adam.Thomson.Opensource@diasemi.com>
Signed-off-by: Steve Twiss <stwiss.opensource@diasemi.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit c842749ea1d32513f9e603c074d60d7aa07cb2ef ]
Commit 71abd29057cb ("spi: imx: Add support for SPI Slave mode") added
an RX FIFO flush before start of a transfer. In slave mode, the master
may have sent more data than expected and this data will still be in the
RX FIFO at the start of the next transfer, and so needs to be flushed.
However, the code to do the flush was accidentally saving this data into
the previous transfer's RX buffer, clobbering the contents of whatever
followed that buffer.
Change it to empty the FIFO and throw away the data. Every one of the
RX functions for the different eCSPI versions and modes reads the RX
FIFO data using the same readl() call, so just use that, rather than
using the spi_imx->rx function pointer and making sure all the different
rx functions have a working "throw away" mode.
There is another issue, which affects master mode when switching from
DMA to PIO. There can be extra data in the RX FIFO which triggers this
flush code, causing memory corruption in the same manner. I don't know
why this data is unexpectedly in the FIFO. It's likely there is a
different bug or erratum responsible for that. But regardless of that,
I think this is proper fix the for bug at hand here.
Fixes: 71abd29057cb ("spi: imx: Add support for SPI Slave mode")
Cc: Jiada Wang <jiada_wang@mentor.com>
Cc: Fabio Estevam <festevam@gmail.com>
Cc: Stefan Agner <stefan@agner.ch>
Cc: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Trent Piepho <tpiepho@impinj.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit f58213637206e190453e3bd91f98f535566290a3 ]
The mutex for the regulator_dev must be controlled by the caller of
the regulator_notifier_call_chain(), as described in the comment
for that function.
Failure to mutex lock and unlock surrounding the notifier call results
in a kernel WARN_ON_ONCE() which will dump a backtrace for the
regulator_notifier_call_chain() when that function call is first made.
The mutex can be controlled using the regulator_lock/unlock() API.
Fixes: f307a7e9b7af ("regulator: pv88060: new regulator driver")
Suggested-by: Adam Thomson <Adam.Thomson.Opensource@diasemi.com>
Signed-off-by: Steve Twiss <stwiss.opensource@diasemi.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit f132da2534ec6599c78c4adcef15340cff2e9dd9 ]
The mutex for the regulator_dev must be controlled by the caller of
the regulator_notifier_call_chain(), as described in the comment
for that function.
Failure to mutex lock and unlock surrounding the notifier call results
in a kernel WARN_ON_ONCE() which will dump a backtrace for the
regulator_notifier_call_chain() when that function call is first made.
The mutex can be controlled using the regulator_lock/unlock() API.
Fixes: 3eb2c7ecb7ea ("regulator: Add LTC3589 support")
Suggested-by: Adam Thomson <Adam.Thomson.Opensource@diasemi.com>
Signed-off-by: Steve Twiss <stwiss.opensource@diasemi.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 769fc8d4182c1d1875db7859852afeb436714c5c ]
The mutex for the regulator_dev must be controlled by the caller of
the regulator_notifier_call_chain(), as described in the comment
for that function.
Failure to mutex lock and unlock surrounding the notifier call results
in a kernel WARN_ON_ONCE() which will dump a backtrace for the
regulator_notifier_call_chain() when that function call is first made.
The mutex can be controlled using the regulator_lock/unlock() API.
Fixes: 37b918a034fe ("regulator: Add LTC3676 support")
Suggested-by: Adam Thomson <Adam.Thomson.Opensource@diasemi.com>
Signed-off-by: Steve Twiss <stwiss.opensource@diasemi.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit f7a621728a6a23bfd2c6ac4d3e42e1303aefde0f ]
The mutex for the regulator_dev must be controlled by the caller of
the regulator_notifier_call_chain(), as described in the comment
for that function.
Failure to mutex lock and unlock surrounding the notifier call results
in a kernel WARN_ON_ONCE() which will dump a backtrace for the
regulator_notifier_call_chain() when that function call is first made.
The mutex can be controlled using the regulator_lock/unlock() API.
Fixes: d4d6b722e780 ("regulator: Add WM831x ISINK support")
Suggested-by: Adam Thomson <Adam.Thomson.Opensource@diasemi.com>
Signed-off-by: Steve Twiss <stwiss.opensource@diasemi.com>
Acked-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 8be64b6d87bd47d81753b60ddafe70102ebfd76b ]
The mutex for the regulator_dev must be controlled by the caller of
the regulator_notifier_call_chain(), as described in the comment
for that function.
Failure to mutex lock and unlock surrounding the notifier call results
in a kernel WARN_ON_ONCE() which will dump a backtrace for the
regulator_notifier_call_chain() when that function call is first made.
The mutex can be controlled using the regulator_lock/unlock() API.
Fixes: d1c6b4fe668b ("regulator: Add WM831x LDO support")
Suggested-by: Adam Thomson <Adam.Thomson.Opensource@diasemi.com>
Signed-off-by: Steve Twiss <stwiss.opensource@diasemi.com>
Acked-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 26843bb128590edd7eba1ad7ce22e4b9f1066ce3 ]
While the sequencer is reset after each SPI message since commit
880c6d114fd79a69 ("spi: rspi: Add support for Quad and Dual SPI
Transfers on QSPI"), it was never reset for the first message, thus
relying on reset state or bootloader settings.
Fix this by initializing it explicitly during configuration.
Fixes: 0b2182ddac4b8837 ("spi: add support for Renesas RSPI")
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 27a7e3e18419869cdcc414a404f3fe66f1b4e644 ]
For HDMI pipelines, when the output gets disconnected the device
handling CEC needs to be notified. Instead of guessing which device that
would be (and sometimes getting it wrong), notify all devices in the
pipeline.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Tested-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit fe4ed1b457943113ee1138c939fbdeede4af6cf3 ]
Currently dsi_display_init_dsi() calls dss_pll_enable() but it is not
paired with dss_pll_disable() in dsi_display_uninit_dsi(). This leaves
the DSS clocks enabled when the display is blanked wasting about extra
5mW of power while idle.
The clock that is left on by not calling dss_pll_disable() is
DSS_CLKCTRL bit 10 OPTFCLKEN_SYS_CLK that is the source clock for
DSI PLL.
We can fix this issue by by making the current dsi_pll_uninit() into
dsi_pll_disable(). This way we can just call dss_pll_disable() from
dsi_display_uninit_dsi() and the code becomes a bit easier to follow.
However, we need to also consider that DSI PLL can be muxed for DVI too
as pointed out by Tomi Valkeinen <tomi.valkeinen@ti.com>. In the DVI
case, we want to unconditionally disable the clocks. To get around this
issue, we separate out the DSI lane handling from dsi_pll_enable() and
dsi_pll_disable() as suggested by Tomi in an earlier experimental patch.
So we must only toggle the DSI regulator based on the vdds_dsi_enabled
flag from dsi_display_init_dsi() and dsi_display_uninit_dsi().
We need to make these two changes together to avoid breaking things
for DVI when fixing the DSI clock handling. And this all causes a
slight renumbering of the error path for dsi_display_init_dsi().
Suggested-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit e482ae9b5fdc01a343f22f52930e85a6cfdf85eb ]
Writeback jobs are allocated when the WRITEBACK_FB_ID is set, and
deleted when the jobs complete. This results in both a memory leak of
the job and a leak of the framebuffer if the atomic commit returns
before the job is queued for processing, for instance if the atomic
check fails or if the commit runs in test-only mode.
Fix this by implementing the drm_writeback_cleanup_job() function and
calling it from __drm_atomic_helper_connector_destroy_state(). As
writeback jobs are removed from the state when they're queued for
processing, any job left in the state when the state gets destroyed
needs to be cleaned up.
The existing declaration of the drm_writeback_cleanup_job() function
without an implementation hints that this problem was considered, but
never addressed.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Reviewed-by: Brian Starkey <brian.starkey@arm.com>
Acked-by: Liviu Dudau <liviu.dudau@arm.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit f37d8e67f39e6d3eaf4cc5471e8a3d21209843c6 ]
pch_alloc_dma_buf allocated tx, rx DMA buffers which can fail. Further,
these buffers are used without a check. The patch checks for these
failures and sends the error upstream.
Signed-off-by: Aditya Pakki <pakki001@umn.edu>
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 9b1640686470fbbd1c6efb35ada6fe1427ea8d0f ]
When unloading the driver, mailbox commands may be sent without holding a
reference on the ndlp. By the time the mailbox command completes, the ndlp
may have reduced its ref counts and been freed. The problem was reported
by KASAN.
While unregistering due to driver unload, have the completion noop'd by
setting the ndlp context NULL'd. Due to the unload, no further action was
necessary. Also, while reviewing this path, the generic nulling of the
context after handling should be slightly moved.
Reported by: Bart Van Assche <bvanassche@acm.org>
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit c95a3b4b0fb8d351e2329a96f87c4fc96a149505 ]
During debug, it was seen that the driver is issuing commands specific to
SLI3 on SLI4 devices. Although the adapter correctly rejected the command,
this should not be done.
Revise the code to stop sending these commands on a SLI4 adapter.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 03aa4f191a36f33fce015387f84efa0eee94408e ]
Two saa7146/hexium files contain a construct that causes a warning
when built with clang:
drivers/media/pci/saa7146/hexium_orion.c:210:12: error: stack frame size of 2272 bytes in function 'hexium_probe'
[-Werror,-Wframe-larger-than=]
static int hexium_probe(struct saa7146_dev *dev)
^
drivers/media/pci/saa7146/hexium_gemini.c:257:12: error: stack frame size of 2304 bytes in function 'hexium_attach'
[-Werror,-Wframe-larger-than=]
static int hexium_attach(struct saa7146_dev *dev, struct saa7146_pci_extension_data *info)
^
This one happens regardless of KASAN, and the problem is that a
constructor to initialize a dynamically allocated structure leads
to a copy of that structure on the stack, whereas gcc initializes
it in place.
Link: https://bugs.llvm.org/show_bug.cgi?id=40776
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: Nick Desaulniers <ndesaulniers@google.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
[hverkuil-cisco@xs4all.nl: fix checkpatch warnings]
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 32a80c093b524a0682f1c6166c910387b116ffce ]
The driver is reporting support for NVME even when not configured for NVME
operation.
Fix (and make more readable) when NVME protocol support is indicated.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit d67f935b79a76ac9d86dde1a27bdd413feb5d987 ]
The FDMI manufacturer value being reported on Linux is inconsistent with
other OS's.
Set the value to "Emulex Corporation" for consistency.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 70a4f5cda82f7197c350099b66fd23506620810e ]
H6 VPU doesn't work if DMA offset is set.
Add a quirk for it.
Signed-off-by: Jernej Skrabec <jernej.skrabec@siol.net>
Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit ea6c7e34f3b28e165988aa7391310752969842e8 ]
It is not possible to use devm_kzalloc since that memory is
freed immediately when the device instance is unbound.
Various objects like the video device may still be in use
since someone has the device node open, and when that is closed
it expects the memory to be around.
So use kzalloc and release it at the appropriate time.
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit f74267b51cb36321f777807b2e04ca02167ecc08 ]
The media_device is part of a static global vimc_device struct.
The media framework expects this to be zeroed before it is
used, however, since this is a global this is not the case if
vimc is unbound and then bound again.
So call memset to ensure any left-over values are cleared.
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit ed713a4a1367aca5c0f2f329579465db00c17995 ]
clang-8 warns about one function here when KASAN is enabled, even
without the 'asan-stack' option:
drivers/media/usb/go7007/go7007-fw.c:1551:5: warning: stack frame size of 2656 bytes in function
I have reported this issue in the llvm bugzilla, but to make
it work with the clang-8 release, a small annotation is still
needed.
Link: https://bugs.llvm.org/show_bug.cgi?id=38809
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
[hverkuil-cisco@xs4all.nl: fix checkpatch warning]
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit e6f8bd59c28f758feea403a70d6c3ef28c50959f ]
When streaming is stopped all URBs are killed, but in fill_frame and in
bulk_irq this results in an attempt to resubmit the killed URB. That is
not what you want and causes spurious kernel messages.
So check if streaming has stopped before resubmitting.
Also check against gspca_dev->streaming rather than vb2_start_streaming_called()
since vb2_start_streaming_called() will return true when in stop_streaming,
but gspca_dev->streaming is set to false when stop_streaming is called.
Fixes: 6992effe5344 ("gspca: Kill all URBs before releasing any of them")
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 2978a505aaa981b279ef359f74ba93d25098e0a0 ]
The state TASK_UNINTERRUPTIBLE should be set just before
schedule_timeout() call, so it knows the sleep mode it should enter.
There is no point in setting TASK_UNINTERRUPTIBLE at the initialization
of the thread as schedule_timeout() will set the state back to
TASK_RUNNING.
This fixes a warning in __might_sleep() call, as it's expecting the
task to be in TASK_RUNNING state just before changing the state to
a sleeping state.
Reported-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Helen Koike <helen.koike@collabora.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 63a06181d7ce169d09843645c50fea1901bc9f0a ]
devm_reset_control_get could fail, so the fix checks its return value and
passes the error code upstream in case it fails.
Signed-off-by: Kangjie Lu <kjlu@umn.edu>
Acked-by: Avri Altman <avri.altman@wdc.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit b9952f93cd2cf5fca82b06a8179c0f5f7b769e83 ]
[Why]
The kms_plane@plane-position-covered-pipe-*-planes subtests can produce
a sequence of atomic commits such that neither active_changed nor
mode_changed but connectors_changed.
When this happens we remove the old stream from the context and add
a new stream but the new stream doesn't have mode_changed=true set.
This incorrect programming sequence causes CRC mismatches to occur in
the test.
The stream->mode_changed value should be set whenever a new stream
is created.
[How]
A new stream is created whenever drm_atomic_crtc_needs_modeset is true.
We previously covered the active_changed and mode_changed conditions
for the CRTC but connectors_changed is also checked within
drm_atomic_crtc_needs_modeset.
So just use drm_atomic_crtc_needs_modeset directly to determine the
mode_changed flag.
Signed-off-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Reviewed-by: Sun peng Li <Sunpeng.Li@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 59979bf8be1784ebfc44215031c6c88ca22ae65d ]
Check if we get any values equal to 0, and set to 1 if so.
Signed-off-by: Murton Liu <murton.liu@amd.com>
Reviewed-by: Aric Cyr <Aric.Cyr@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Acked-by: Sivapiriyan Kumarasamy <Sivapiriyan.Kumarasamy@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
