| Age | Commit message (Collapse) | Author |
|---|
|
This patch uses the resource-managed extcon API for extcon_register_notifier()
and replaces the deprecated extcon API as following:
- extcon_get_cable_state_() -> extcon_get_state()
Cc: linux-omap@vger.kernel.org
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
Acked-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
|
|
Instead of passing quirk_ep_out_aligned_size, we can use one extra TRB
to align transfer to wMaxPacketSize.
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
|
|
Allocate a coherent buffer of 1024 bytes (size of a single superspeed
bulk packet) to serve as bounce buffer for an extra TRB needed to align
transfers to wMaxPacketSize.
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
|
|
This new internal function will be used to solve a minor issue with dwc3
which exists in regards to short packets with OUT endpoints. Currently
we're asking gadget driver to *always* send us aligned requests; however
if we have enough TRBs we can easily append one extra TRB chained to the
previous and keep a throw away 1024 byte buffer around for that.
The actual fix will come in a separate patch, this is merely in
preparation for such fix.
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
|
|
We are already passing struct dwc3_request * to dwc3_prepare_one_trb(),
because of that there's no need to extract dma address and length in the
caller. We can let dwc3_prepare_one_trb() itself handle that part.
This simplifies the prototype of the function by removing two arguments.
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
|
|
If it is out of memory, we should return -ENOMEM;
Signed-off-by: Peter Chen <peter.chen@nxp.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
|
|
For boolean variables true/false is preferred over 1/0 for readability.
Acked-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Nicholas Mc Guire <hofrat@osadl.org>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
|
|
ulseep_range() uses hrtimers and provides no advantage over msleep()
for larger delays. Fix up the 20+ ms delays here passing the adjusted "min"
value to msleep(). This helps reduce the load on the hrtimer subsystem.
Acked-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Nicholas Mc Guire <hofrat@osadl.org>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
|
|
Exynos is DT-only, so there's no need for a platform MODALIAS.
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
|
|
dwc3-exynos prints debug message when suspend clock is not specified.
The suspend clock is optional and driver can work without it.
This debug message doesn't add any value and leads to confusion and
concern. Remove it.
Signed-off-by: Shuah Khan <shuahkh@osg.samsung.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
|
|
Declare usb_gadget_ops structures as const as they are only stored in
the ops field of a usb_gadget structure. This field is of type const, so
usb_gadget_ops structures having this property can be declared const
too.
Done using Coccinelle:
@r1 disable optional_qualifier@
identifier i;
position p;
@@
static struct usb_gadget_ops i@p={...};
@ok1@
identifier r1.i;
position p;
struct fotg210_udc fotg210;
@@
fotg210.gadget.ops=&i@p
@bad@
position p!={r1.p,ok1.p};
identifier r1.i;
@@
i@p
@depends on !bad disable optional_qualifier@
identifier r1.i;
@@
+const
struct usb_gadget_ops i;
File size before:
text data bss dec hex filename
7559 384 8 7951 1f0f usb/gadget/udc/fotg210-udc.o
File size after:
text data bss dec hex filename
7655 288 8 7951 1f0f usb/gadget/udc/fotg210-udc.o
Signed-off-by: Bhumika Goyal <bhumirks@gmail.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
|
|
Commit 05ee799f2021 ("usb: dwc2: Move gadget settings into core_params")
changes to type u16 for DT binding "g-rx-fifo-size" and
"g-np-tx-fifo-size" but use type u32 for "g-tx-fifo-size". Finally the
the first two parameters cannot be passed successfully with wrong data
format. This is found the data transferring broken on 96boards Hikey.
This patch is to change all parameters to u32 type, and verified on
Hikey board the DT parameters can pass successfully.
[johnyoun: minor rebase]
Signed-off-by: Leo Yan <leo.yan@linaro.org>
Signed-off-by: John Youn <johnyoun@synopsys.com>
Tested-by: John Stultz <john.stultz@linaro.org>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
|
|
trivial fix to typo in dev_dbg message
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
|
|
pnp string is usually much shorter than 1k so let's stop wasting 1k of
memory for its buffer and make it dynamically alocated.
This also removes 1k len limitation for pnp_string and
adds a new line after string content if required.
Signed-off-by: Krzysztof Opasiak <k.opasiak@samsung.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
|
|
Generally in SysFS and ConfigFS files are new line terminated.
Also most of USB functions adds a trailing newline to each attribute.
Let's follow this convention also in ethernet functions.
Signed-off-by: Krzysztof Opasiak <k.opasiak@samsung.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
|
|
Since:
commit 855ed04a3758 ("usb: gadget: udc-core: independent registration
of gadgets and gadget drivers")
if we load gadget module but there is no free udc available
then it will be stored on a pending gadgets list.
$ modprobe g_zero.ko
$ modprobe g_ether.ko
[] udc-core: couldn't find an available UDC - added [g_ether] to list
of pending drivers
We scan this list each time when new UDC appears in system.
But we can get a free UDC each time after gadget unbind.
This commit add scanning of that list directly after unbinding
gadget from udc.
Thanks to this, when we unload first gadget:
$ rmmod g_zero.ko
gadget which is pending is automatically
attached to that UDC (if name matches).
Fixes: 855ed04a3758 ("usb: gadget: udc-core: independent registration of gadgets and gadget drivers")
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Krzysztof Opasiak <k.opasiak@samsung.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
|
|
Similar as commit 2b2fe36def08 ("usb: chipidea: imx: delete the
redundant setting default DMA mask code"), the ci_hdrc_usb2 platform
device is also created by device tree, the default DMA mask should be
already set by of_dma_configure when the device are created. So delete
the redundant code at driver.
Signed-off-by: Jisheng Zhang <jszhang@marvell.com>
Signed-off-by: Peter Chen <peter.chen@nxp.com>
|
|
<linux/phy.h> is for net phy drivers, we don't need it.
Signed-off-by: Jisheng Zhang <jszhang@marvell.com>
Signed-off-by: Peter Chen <peter.chen@nxp.com>
|
|
The warn on is a bit too much, we will anyway set the dma mask if not set
previously.
The main reason for this fix is that 4.10-rc1 has a dwc3 change that
pass a parent sysdev dev pointer instead of setting the dma mask of
its xhci platform device. xhci platform driver can then get more
attributes from the sysdev than just the dma mask.
The usb core and xhci changes are not yet in 4.10, and a fix like
this was preferred instead of taking those big changes this late in
the rc-cycle.
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
The CI_HDRC_CONTROLLER_STOPPED_EVENT may want to call sleeping
APIs similar to how _gadget_stop_activity() may. Let's drop the
lock across the event so that glue drivers can make sleeping
calls.
Cc: Peter Chen <peter.chen@nxp.com>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Stephen Boyd <stephen.boyd@linaro.org>
Signed-off-by: Peter Chen <peter.chen@nxp.com>
|
|
If something fails in ci_hdrc_add_device() due to probe defer, we
shouldn't print an error message. Be silent in this case as we'll
try probe again later.
Acked-by: Peter Chen <peter.chen@nxp.com>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Stephen Boyd <stephen.boyd@linaro.org>
Signed-off-by: Peter Chen <peter.chen@nxp.com>
|
|
The ULPI phy on qcom platforms needs to be initialized and
powered on after a USB reset and before we toggle the run/stop
bit. Otherwise, the phy locks up and doesn't work properly. Hook
the phy initialization into the RESET event and the phy power off
into the STOPPED event.
Acked-by: Peter Chen <peter.chen@nxp.com>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Stephen Boyd <stephen.boyd@linaro.org>
Signed-off-by: Peter Chen <peter.chen@nxp.com>
|
|
The MSM chipidea wrapper has two bits that are used to reset the
first or second phy. Add support for these bits via the reset
controller framework, so that phy drivers can reset their
hardware at the right time during initialization.
Acked-by: Peter Chen <peter.chen@nxp.com>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Stephen Boyd <stephen.boyd@linaro.org>
Signed-off-by: Peter Chen <peter.chen@nxp.com>
|
|
If two devices are probed with this same driver, they'll share
the same platform data structure, while the chipidea core layer
writes and modifies it. This can lead to interesting results
especially if one device is an OTG type chipidea controller and
another is a host. Let's create a copy of this structure per each
device instance so that odd things don't happen.
Acked-by: Peter Chen <peter.chen@nxp.com>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Stephen Boyd <stephen.boyd@linaro.org>
Signed-off-by: Peter Chen <peter.chen@nxp.com>
|
|
When the RESET bit is set in the USBCMD register it resets quite
a few of the wrapper's registers to their reset state. This
includes the GENCONFIG and GENCONFIG2 registers. Currently this
is done by the usb phy and ehci-msm drivers writing into the
controller wrapper's MMIO address space. Let's consolidate the
register writes into the wrapper driver instead so that we
clearly split the wrapper from the phys.
Acked-by: Peter Chen <peter.chen@nxp.com>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Stephen Boyd <stephen.boyd@linaro.org>
Signed-off-by: Peter Chen <peter.chen@nxp.com>
|
|
We need to pick the correct phy at runtime based on how the SoC
has been wired onto the board. If the secondary phy is used, take
it out of reset and mux over to it by writing into the TCSR
register. Make sure to do this on reset too, because this
register is reset to the default value (primary phy) after the
RESET bit is set in USBCMD.
Acked-by: Peter Chen <peter.chen@nxp.com>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Stephen Boyd <stephen.boyd@linaro.org>
Signed-off-by: Peter Chen <peter.chen@nxp.com>
|
|
The msm chipidea controller uses two main clks, an AHB clk to
read/write the MMIO registers and a core clk called the system
clk that drives the controller itself. Add support for these clks
as they're required in all designs.
Also add support for an optional third clk that we need to turn
on to reset the controller and wrapper logic and other
"housekeeping" things. This clk was removed in later revisions of
the hardware because the reset methodology no longer required
clks to be enabled to propagate resets.
Acked-by: Peter Chen <peter.chen@nxp.com>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Stephen Boyd <stephen.boyd@linaro.org>
Signed-off-by: Peter Chen <peter.chen@nxp.com>
|
|
The MSM_USB_BASE macro trick is not very clear, and we're using
it for only one register write so let's just move to using
hw_write_id_reg() and passing the ci pointer instead. That
clearly shows what offset we're using and avoids needing to
include the msm_hsusb_hw.h file when we're going to delete that
file soon.
Acked-by: Peter Chen <peter.chen@nxp.com>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Stephen Boyd <stephen.boyd@linaro.org>
Signed-off-by: Peter Chen <peter.chen@nxp.com>
|
|
The core framework already handles setting this parameter with a
platform quirk. Add the appropriate flag so that we always set
AHBBURST to 0. Technically DT should be doing this, but we always
do it for msm chipidea devices so setting the flag in the driver
works just as well. If the burst needs to be anything besides 0,
we expect the 'ahb-burst-config' dts property to be present.
Acked-by: Peter Chen <peter.chen@nxp.com>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Stephen Boyd <stephen.boyd@linaro.org>
Signed-off-by: Peter Chen <peter.chen@nxp.com>
|
|
We're not properly marking the glue layer/wrapper device as
runtime active, so runtime PM believes that the hardware state is
inactive when we call pm_runtime_enable() in this driver. This
causes a problem when the glue layer has a power domain
associated with it, because runtime PM will go and disable the
power domain to match the 'inactive' state of the device. Let's
mark the device as active so that runtime PM doesn't improperly
power down this device when it's actually active.
Acked-by: Peter Chen <peter.chen@nxp.com>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Stephen Boyd <stephen.boyd@linaro.org>
Signed-off-by: Peter Chen <peter.chen@nxp.com>
|
|
At some situations, the vbus may already be there before starting
gadget. So we need to check vbus event after switching to gadget in
order to handle missing vbus event. The typical use cases are plugging
vbus cable before driver load or the vbus has already been there
after stopping host but before starting gadget.
Signed-off-by: Peter Chen <peter.chen@nxp.com>
Tested-by: Stephen Boyd <stephen.boyd@linaro.org>
Reported-by: Stephen Boyd <stephen.boyd@linaro.org>
|
|
The two extcon notifiers are almost the same except for the
variable name for the cable structure and the id notifier inverts
the cable->state logic. Make it the same and replace two
functions with one to save some lines. This also makes it so that
the id cable state is true when the id pin is pulled low, so we
change the name of ->state to ->connected to properly reflect
that we're interested in the cable being connected.
Acked-by: Peter Chen <peter.chen@nxp.com>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: "Ivan T. Ivanov" <iivanov.xz@gmail.com>
Signed-off-by: Stephen Boyd <stephen.boyd@linaro.org>
Signed-off-by: Peter Chen <peter.chen@nxp.com>
|
|
Some phys for the chipidea controller are controlled via the ULPI
viewport. Add support for the ULPI bus so that these sorts of
phys can be probed and read/written automatically without having
to duplicate the viewport logic in each phy driver.
Acked-by: Peter Chen <peter.chen@nxp.com>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Stephen Boyd <stephen.boyd@linaro.org>
Signed-off-by: Peter Chen <peter.chen@nxp.com>
|
|
We don't call hw_device_reset() with the ci->lock held, so it
doesn't seem like this lock here is protecting anything. Let's
just remove it. This allows us to call sleeping functions like
phy_init() from within the CI_HDRC_CONTROLLER_RESET_EVENT hook.
Acked-by: Peter Chen <peter.chen@nxp.com>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Stephen Boyd <stephen.boyd@linaro.org>
Signed-off-by: Peter Chen <peter.chen@nxp.com>
|
|
The chipidea/udc.c file sends a CI_HDRC_CONTROLLER_RESET_EVENT to
the wrapper drivers when it calls hw_device_reset(), but that
function is not called from chipidea/host.c. And the udc.c file
sends the CI_HDRC_CONTROLLER_STOPPED_EVENT but the host.c file
doesn't do anything.
The intent of the reset event is to allow the wrapper driver to
do any wrapper specific things after the reset bit has been set
in the usb command register. Therefore, add this event hook in
the host role after we toggle that bit.
Similarly, the intent of the stopped event is to allow the
wrapper driver to do any wrapper specific things after the device
is stopped. So when we stop the host role, send the stopped
event.
Acked-by: Peter Chen <peter.chen@nxp.com>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Stephen Boyd <stephen.boyd@linaro.org>
Signed-off-by: Peter Chen <peter.chen@nxp.com>
|
|
The ULPI phy on qcom platforms needs to be initialized and
powered on after a USB reset and before we toggle the run/stop
bit. Otherwise, the phy locks up and doesn't work properly.
Therefore, add a flag to skip any phy power management in the
core layer, leaving it up to the glue driver to manage.
Acked-by: Peter Chen <peter.chen@nxp.com>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Stephen Boyd <stephen.boyd@linaro.org>
Signed-off-by: Peter Chen <peter.chen@nxp.com>
|
|
We're currently emulating the vbus and id interrupts in the OTGSC
read API, but we also need to make sure that if we're handling
the events with extcon that we don't enable the interrupts for
those events in the hardware. Therefore, properly emulate this
register if we're using extcon, but don't enable the interrupts.
This allows me to get my cable connect/disconnect working
properly without getting spurious interrupts on my device that
uses an extcon for these two events.
Acked-by: Peter Chen <peter.chen@nxp.com>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: "Ivan T. Ivanov" <iivanov.xz@gmail.com>
Fixes: 3ecb3e09b042 ("usb: chipidea: Use extcon framework for VBUS and ID detect")
Signed-off-by: Stephen Boyd <stephen.boyd@linaro.org>
Signed-off-by: Peter Chen <peter.chen@nxp.com>
|
|
With the id and vbus detection done via extcon we need to make
sure we poll the status of OTGSC properly by considering what the
extcon is saying, and not just what the register is saying. Let's
move this hw_wait_reg() function to the only place it's used and
simplify it for polling the OTGSC register. Then we can make
certain we only use the hw_read_otgsc() API to read OTGSC, which
will make sure we properly handle extcon events.
Acked-by: Peter Chen <peter.chen@nxp.com>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: "Ivan T. Ivanov" <iivanov.xz@gmail.com>
Fixes: 3ecb3e09b042 ("usb: chipidea: Use extcon framework for VBUS and ID detect")
Signed-off-by: Stephen Boyd <stephen.boyd@linaro.org>
Signed-off-by: Peter Chen <peter.chen@nxp.com>
|
|
The qcom HSIC ULPI phy doesn't have any bits set in the vendor or
product ID registers. This makes it impossible to make a ULPI
driver match against the ID registers. Add support to discover
the ULPI phys via DT help alleviate this problem. In the DT case,
we'll look for a ULPI bus node underneath the device registering
the ULPI viewport (or the parent of that device to support
chipidea's device layout) and then match up the phy node
underneath that with the ULPI device that's created.
The side benefit of this is that we can use standard properties
in the phy node like clks, regulators, gpios, etc. because we
don't have firmware like ACPI to turn these things on for us. And
we can use the DT phy binding to point our phy consumer to the
phy provider.
The ULPI bus code supports native enumeration by reading the
vendor ID and product ID registers at device creation time, but
we can't be certain that those register reads will succeed if the
phy is not powered up. To avoid any problems with reading the ID
registers before the phy is powered we fallback to DT matching
when the ID reads fail.
If the ULPI spec had some generic power sequencing for these
registers we could put that into the ULPI bus layer and power up
the device before reading the ID registers. Unfortunately this
doesn't exist and the power sequence is usually device specific.
By having the device matched up with DT we can avoid this
problem.
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Acked-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Cc: <devicetree@vger.kernel.org>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Stephen Boyd <stephen.boyd@linaro.org>
Signed-off-by: Peter Chen <peter.chen@nxp.com>
|
|
This patch uses the resource-managed extcon API for extcon_register_notifier()
and replaces the deprecated extcon API as following:
- extcon_get_cable_state_() -> extcon_get_state()
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
Signed-off-by: Peter Chen <peter.chen@nxp.com>
|
|
usually, the reference clock comes from 26M oscillator directly,
but some SoCs are not, add it for compatibility.
Signed-off-by: Chunfeng Yun <chunfeng.yun@mediatek.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
usually, the reference clock comes from 26M oscillator directly,
but some SoCs are not, add it for compatibility.
Signed-off-by: Chunfeng Yun <chunfeng.yun@mediatek.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Some resources such as regulator, clock usually cause deferred
probe, get them earlier to avoid more ineffective processing.
Signed-off-by: Chunfeng Yun <chunfeng.yun@mediatek.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
The commit 4ac53087d6d4 ("usb: xhci: plat: Create both
HCDs before adding them") move add hcd to the end of
probe, this cause hcc_params uninitiated, because xHCI
driver sets hcc_params in xhci_gen_setup() called from
usb_add_hcd().
This patch checks the Maximum Primary Stream Array Size
in the hcc_params register after add primary hcd.
Signed-off-by: William wu <william.wu@rock-chips.com>
Acked-by: Roger Quadros <rogerq@ti.com>
Cc: stable <stable@vger.kernel.org> # 4.2+
Fixes: 4ac53087d6d4 ("usb: xhci: plat: Create both HCDs before adding them")
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Declare dev_pm_ops structures as const as they are only stored in the pm
field of a device_driver structure. This field is of type const, so
dev_pm_ops structures having similar properties can be declared const
too.
Size details after cross compiling the .o file for powerpc
architecture.
File size before:
text data bss dec hex filename
3183 372 0 3555 de3 drivers/usb/host/ehci-fsl.o
File size after:
text data bss dec hex filename
3275 280 0 3555 de3 drivers/usb/host/ehci-fsl.o
Signed-off-by: Bhumika Goyal <bhumirks@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Declare usb_gadget_ops structures as const as they are only stored in
the ops field of a usb_gadget structure. This field is of type const, so
usb_gadget_ops structures having this property can be declared const
too.
Done using Coccinelle:
@r1 disable optional_qualifier@
identifier i;
position p;
@@
static struct usb_gadget_ops i@p={...};
@ok1@
identifier r1.i;
position p;
struct isp1760_udc udc;
@@
udc.gadget.ops=&i@p
@bad@
position p!={r1.p,ok1.p};
identifier r1.i;
@@
i@p
@depends on !bad disable optional_qualifier@
identifier r1.i;
@@
+const
struct usb_gadget_ops i;
File size before: drivers/usb/isp1760/isp1760-udc.o
text data bss dec hex filename
12434 4136 16 16586 40ca usb/isp1760/isp1760-udc.o
File size after: drivers/usb/isp1760/isp1760-udc.o
text data bss dec hex filename
12530 4048 16 16594 40d2 usb/isp1760/isp1760-udc.o
Signed-off-by: Bhumika Goyal <bhumirks@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Declare usb_gadget_ops structures as const as they are only stored in
the ops field of a usb_gadget structure. This field is of type const, so
usb_gadget_ops structures having this property can be declared const
too.
Done using Coccinelle:
@r1 disable optional_qualifier@
identifier i;
position p;
@@
static struct usb_gadget_ops i@p={...};
@ok1@
identifier r1.i;
position p;
struct fotg210_udc fotg210;
@@
fotg210.gadget.ops=&i@p
@bad@
position p!={r1.p,ok1.p};
identifier r1.i;
@@
i@p
@depends on !bad disable optional_qualifier@
identifier r1.i;
@@
+const
struct usb_gadget_ops i;
File size before:
text data bss dec hex filename
7559 384 8 7951 1f0f usb/gadget/udc/fotg210-udc.o
File size after:
text data bss dec hex filename
7655 288 8 7951 1f0f usb/gadget/udc/fotg210-udc.o
Signed-off-by: Bhumika Goyal <bhumirks@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
On some platforms(e.g. rk3399 board), we can call hcd_add/remove
consecutively without calling usb_put_hcd/usb_create_hcd in between,
so hcd->flags can be stale.
If the HC dies due to whatever reason then without this patch we get
the below error on next hcd_add.
[173.296154] xhci-hcd xhci-hcd.2.auto: HC died; cleaning up
[173.296209] xhci-hcd xhci-hcd.2.auto: xHCI Host Controller
[173.296762] xhci-hcd xhci-hcd.2.auto: new USB bus registered, assigned bus number 6
[173.296931] usb usb6: We don't know the algorithms for LPM for this host, disabling LPM.
[173.297179] usb usb6: New USB device found, idVendor=1d6b, idProduct=0003
[173.297203] usb usb6: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[173.297222] usb usb6: Product: xHCI Host Controller
[173.297240] usb usb6: Manufacturer: Linux 4.4.21 xhci-hcd
[173.297257] usb usb6: SerialNumber: xhci-hcd.2.auto
[173.298680] hub 6-0:1.0: USB hub found
[173.298749] hub 6-0:1.0: 1 port detected
[173.299382] rockchip-dwc3 usb@fe800000: USB HOST connected
[173.395418] hub 5-0:1.0: activate --> -19
[173.603447] irq 228: nobody cared (try booting with the "irqpoll" option)
[173.603493] CPU: 0 PID: 0 Comm: swapper/0 Not tainted 4.4.21 #9
[173.603513] Hardware name: Google Kevin (DT)
[173.603531] Call trace:
[173.603568] [<ffffffc0002087dc>] dump_backtrace+0x0/0x160
[173.603596] [<ffffffc00020895c>] show_stack+0x20/0x28
[173.603623] [<ffffffc0004b28a8>] dump_stack+0x90/0xb0
[173.603650] [<ffffffc00027347c>] __report_bad_irq+0x48/0xe8
[173.603674] [<ffffffc0002737cc>] note_interrupt+0x1e8/0x28c
[173.603698] [<ffffffc000270a38>] handle_irq_event_percpu+0x1d4/0x25c
[173.603722] [<ffffffc000270b0c>] handle_irq_event+0x4c/0x7c
[173.603748] [<ffffffc00027456c>] handle_fasteoi_irq+0xb4/0x124
[173.603777] [<ffffffc00026fe3c>] generic_handle_irq+0x30/0x44
[173.603804] [<ffffffc0002701a8>] __handle_domain_irq+0x90/0xbc
[173.603827] [<ffffffc0002006f4>] gic_handle_irq+0xcc/0x188
...
[173.604500] [<ffffffc000203700>] el1_irq+0x80/0xf8
[173.604530] [<ffffffc000261388>] cpu_startup_entry+0x38/0x3cc
[173.604558] [<ffffffc00090f7d8>] rest_init+0x8c/0x94
[173.604585] [<ffffffc000e009ac>] start_kernel+0x3d0/0x3fc
[173.604607] [<0000000000b16000>] 0xb16000
[173.604622] handlers:
[173.604648] [<ffffffc000642084>] usb_hcd_irq
[173.604673] Disabling IRQ #228
Signed-off-by: William wu <wulf@rock-chips.com>
Acked-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
The variable Newblk was only being assigned some value but was never
used after that.
Signed-off-by: Sudip Mukherjee <sudip.mukherjee@codethink.co.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
The variable live was assigned the host controller running status but
it was never used or checked after that.
Signed-off-by: Sudip Mukherjee <sudip.mukherjee@codethink.co.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
