| Age | Commit message (Collapse) | Author |
|---|
|
[ Upstream commit dd33993a9721ab1dae38bd37c9f665987d554239 ]
s/devince/device/
It's used only internally, so no any behavior changes.
Fixes: 37e0e14128e0 ("ALSA: ump: Support UMP Endpoint and Function Block parsing")
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Link: https://patch.msgid.link/20250511141147.10246-1-tiwai@suse.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit cab63934c33b12c0d1e9f4da7450928057f2c142 ]
Event polling delay is set to 0 if there are any pending requests in
either rx or tx requests lists. Checking for pending requests does
not work well for "IN" transfers as the tty driver always queues
requests to the list and TRBs to the ring, preparing to receive data
from the host.
This causes unnecessary busylooping and cpu hogging.
Only set the event polling delay to 0 if there are pending tx "write"
transfers, or if it was less than 10ms since last active data transfer
in any direction.
Cc: Łukasz Bartosik <ukaszb@chromium.org>
Fixes: fb18e5bb9660 ("xhci: dbc: poll at different rate depending on data transfer activity")
Cc: stable@vger.kernel.org
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20250505125630.561699-3-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 03e3d9c2bd85cda941b3cf78e895c1498ac05c5f ]
Queue event polling work with 0 delay in case there are pending transfers
queued up. This is part 2 of a 3 part series that roughly triples dbc
performace when using adb push and pull over dbc.
Max/min push rate after patches is 210/118 MB/s, pull rate 171/133 MB/s,
tested with large files (300MB-9GB) by Łukasz Bartosik
First performance improvement patch was commit 31128e7492dc
("xhci: dbc: add dbgtty request to end of list once it completes")
Cc: Łukasz Bartosik <ukaszb@chromium.org>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20241227120142.1035206-2-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Stable-dep-of: cab63934c33b ("xhci: dbc: Avoid event polling busyloop if pending rx transfers are inactive.")
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
commit 4e77d3ec7c7c0d9535ccf1138827cb9bb5480b9b upstream.
wait_event_interruptible_timeout returns a long
The return value was being assigned to an int causing an integer overflow
when the remaining jiffies > INT_MAX which resulted in random error
returns.
Use a long return value, converting to the int ioctl return only on error.
Fixes: bb99794a4792 ("usb: usbtmc: Add ioctl for vendor specific read")
Cc: stable@vger.kernel.org
Signed-off-by: Dave Penkler <dpenkler@gmail.com>
Link: https://lore.kernel.org/r/20250502070941.31819-4-dpenkler@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit a9747c9b8b59ab4207effd20eb91a890acb44e16 upstream.
wait_event_interruptible_timeout returns a long
The return was being assigned to an int causing an integer overflow when
the remaining jiffies > INT_MAX resulting in random error returns.
Use a long return value, converting to the int ioctl return only on
error.
Fixes: 739240a9f6ac ("usb: usbtmc: Add ioctl USBTMC488_IOCTL_WAIT_SRQ")
Cc: stable@vger.kernel.org
Signed-off-by: Dave Penkler <dpenkler@gmail.com>
Link: https://lore.kernel.org/r/20250502070941.31819-3-dpenkler@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit cac01bd178d6a2a23727f138d647ce1a0e8a73a1 upstream.
wait_event_interruptible_timeout returns a long
The return was being assigned to an int causing an integer overflow when
the remaining jiffies > INT_MAX resulting in random error returns.
Use a long return value and convert to int ioctl return only on error.
When the return value of wait_event_interruptible_timeout was <= INT_MAX
the number of remaining jiffies was returned which has no meaning for the
user. Return 0 on success.
Reported-by: Michael Katzmann <vk2bea@gmail.com>
Fixes: dbf3e7f654c0 ("Implement an ioctl to support the USMTMC-USB488 READ_STATUS_BYTE operation.")
Cc: stable@vger.kernel.org
Signed-off-by: Dave Penkler <dpenkler@gmail.com>
Link: https://lore.kernel.org/r/20250502070941.31819-2-dpenkler@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 054c5145540e5ad5b80adf23a5e3e2fc281fb8aa upstream.
usbtmc_read() calls usbtmc_generic_read()
which uses interruptible sleep, but usbtmc_read()
itself uses uninterruptble sleep for mutual exclusion
between threads. That makes no sense.
Both should use interruptible sleep.
Fixes: 5b775f672cc99 ("USB: add USB test and measurement class driver")
Cc: stable <stable@kernel.org>
Signed-off-by: Oliver Neukum <oneukum@suse.com>
Link: https://lore.kernel.org/r/20250430134810.226015-1-oneukum@suse.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 312d79669e71283d05c05cc49a1a31e59e3d9e0e upstream.
This patch ensures that the UCSI driver waits for all pending tasks in the
ucsi_displayport_work workqueue to finish executing before proceeding with
the partner removal.
Cc: stable <stable@kernel.org>
Fixes: af8622f6a585 ("usb: typec: ucsi: Support for DisplayPort alt mode")
Signed-off-by: Andrei Kuchynski <akuchynski@chromium.org>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Reviewed-by: Benson Leung <bleung@chromium.org>
Link: https://lore.kernel.org/r/20250424084429.3220757-3-akuchynski@chromium.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit e918d3959b5ae0e793b8f815ce62240e10ba03a4 upstream.
This patch fixes Type-C Compliance Test TD 4.7.6 - Try.SNK DRP Connect
SNKAS.
The compliance tester moves into SNK_UNATTACHED during toggling and
expects the PUT to apply Rp after tPDDebounce of detection. If the port
is in SNK_TRY_WAIT_DEBOUNCE, it will move into SRC_TRYWAIT immediately
and apply Rp. This violates TD 4.7.5.V.3, where the tester confirms that
the PUT attaches Rp after the transitions to Unattached.SNK for
tPDDebounce.
Change the tcpm_set_state delay between SNK_TRY_WAIT_DEBOUNCE and
SRC_TRYWAIT to tPDDebounce.
Fixes: a0a3e04e6b2c ("staging: typec: tcpm: Check for Rp for tPDDebounce")
Cc: stable <stable@kernel.org>
Signed-off-by: RD Babiera <rdbabiera@google.com>
Reviewed-by: Badhri Jagan Sridharan <badhri@google.com>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Link: https://lore.kernel.org/r/20250429234703.3748506-2-rdbabiera@google.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 9f657a92805cfc98e11cf5da9e8f4e02ecff2260 upstream.
The Cypress HX3 USB3.0 hubs use different PID values depending
on the product variant. The comment in compatibles table is
misleading, as the currently used PIDs (0x6504 and 0x6506 for
USB 3.0 and USB 2.0, respectively) are defaults for the CYUSB331x,
while CYUSB330x and CYUSB332x variants use different values.
Based on the datasheet [1], update the compatible usb devices table
to handle different types of the hub.
The change also includes vendor mode PIDs, which are used by the
hub in I2C Master boot mode, if connected EEPROM contains invalid
signature or is blank. This allows to correctly boot the hub even
if the EEPROM will have broken content.
Number of vcc supplies and timing requirements are the same for all
HX variants, so the platform driver's match table does not have to
be extended.
[1] https://www.infineon.com/dgdl/Infineon-HX3_USB_3_0_Hub_Consumer_Industrial-DataSheet-v22_00-EN.pdf?fileId=8ac78c8c7d0d8da4017d0ecb53f644b8
Table 9. PID Values
Fixes: b43cd82a1a40 ("usb: misc: onboard-hub: add support for Cypress HX3 USB 3.0 family")
Cc: stable <stable@kernel.org>
Signed-off-by: Lukasz Czechowski <lukasz.czechowski@thaumatec.com>
Link: https://lore.kernel.org/r/20250425-onboard_usb_dev-v2-1-4a76a474a010@thaumatec.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 732f35cf8bdfece582f6e4a9c659119036577308 upstream.
When a USB device is connected to the OTG port, the tegra_xhci_id_work()
routine transitions the PHY to host mode and calls xhci_hub_control()
with the SetPortFeature command to enable port power.
In certain cases, the XHCI controller may be in a low-power state
when this operation occurs. If xhci_hub_control() is invoked while
the controller is suspended, the PORTSC register may return 0xFFFFFFFF,
indicating a read failure. This causes xhci_hc_died() to be triggered,
leading to host controller shutdown.
Example backtrace:
[ 105.445736] Workqueue: events tegra_xhci_id_work
[ 105.445747] dump_backtrace+0x0/0x1e8
[ 105.445759] xhci_hc_died.part.48+0x40/0x270
[ 105.445769] tegra_xhci_set_port_power+0xc0/0x240
[ 105.445774] tegra_xhci_id_work+0x130/0x240
To prevent this, ensure the controller is fully resumed before
interacting with hardware registers by calling pm_runtime_get_sync()
prior to the host mode transition and xhci_hub_control().
Fixes: f836e7843036 ("usb: xhci-tegra: Add OTG support")
Cc: stable <stable@kernel.org>
Signed-off-by: Jim Lin <jilin@nvidia.com>
Signed-off-by: Wayne Chang <waynec@nvidia.com>
Link: https://lore.kernel.org/r/20250422114001.126367-1-waynec@nvidia.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 5977a58dd5a4865198b0204b998adb0f634abe19 upstream.
Currently when the host sends GET_STATUS request for an interface,
we use get_status callbacks to set/clear remote wakeup capability
of that interface. And if get_status callback isn't present for
that interface, then we assume its remote wakeup capability based
on bmAttributes.
Now consider a scenario, where we have a USB configuration with
multiple interfaces (say ECM + ADB), here ECM is remote wakeup
capable and as of now ADB isn't. And bmAttributes will indicate
the device as wakeup capable. With the current implementation,
when host sends GET_STATUS request for both interfaces, we will
set FUNC_RW_CAP for both. This results in USB3 CV Chapter 9.15
(Function Remote Wakeup Test) failures as host expects remote
wakeup from both interfaces.
The above scenario is just an example, and the failure can be
observed if we use configuration with any interface except ECM.
Hence avoid configuring remote wakeup capability from composite
driver based on bmAttributes, instead use get_status callbacks
and let the function drivers decide this.
Cc: stable <stable@kernel.org>
Fixes: 481c225c4802 ("usb: gadget: Handle function suspend feature selector")
Signed-off-by: Prashanth K <prashanth.k@oss.qualcomm.com>
Reviewed-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com>
Link: https://lore.kernel.org/r/20250422103231.1954387-3-prashanth.k@oss.qualcomm.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 59820fde001500c167342257650541280c622b73 upstream.
We identified a bug where the ST_RC bit in the status register was not
being acknowledged after clearing the CTRL_RUN bit in the control
register. This could lead to unexpected behavior in the USB gadget
drivers.
This patch resolves the issue by adding the necessary code to explicitly
acknowledge ST_RC after clearing CTRL_RUN based on the programming
sequence, ensuring proper state transition.
Fixes: 49db427232fe ("usb: gadget: Add UDC driver for tegra XUSB device mode controller")
Cc: stable <stable@kernel.org>
Signed-off-by: Wayne Chang <waynec@nvidia.com>
Link: https://lore.kernel.org/r/20250418081228.1194779-1-waynec@nvidia.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 8e3820271c517ceb89ab7442656ba49fa23ee1d0 upstream.
When host sends GET_STATUS to ECM interface, handle the request
from the function driver. Since the interface is wakeup capable,
set the corresponding bit, and set RW bit if the function is
already armed for wakeup by the host.
Cc: stable <stable@kernel.org>
Fixes: 481c225c4802 ("usb: gadget: Handle function suspend feature selector")
Signed-off-by: Prashanth K <prashanth.k@oss.qualcomm.com>
Reviewed-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com>
Link: https://lore.kernel.org/r/20250422103231.1954387-2-prashanth.k@oss.qualcomm.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 8614ecdb1570e4fffe87ebdc62b613ed66f1f6a6 upstream.
The controllers with rtl version larger than
RTL_REVISION_NEW_LPM (0x00002700) has bug which causes that controller
doesn't resume from L1 state. It happens if after receiving LPM packet
controller starts transitioning to L1 and in this moment the driver force
resuming by write operation to PORTSC.PLS.
It's corner case and happens when write operation to PORTSC occurs during
device delay before transitioning to L1 after transmitting ACK
time (TL1TokenRetry).
Forcing transition from L1->L0 by driver for revision larger than
RTL_REVISION_NEW_LPM is not needed, so driver can simply fix this issue
through block call of cdnsp_force_l0_go function.
Fixes: 3d82904559f4 ("usb: cdnsp: cdns3 Add main part of Cadence USBSSP DRD Driver")
Cc: stable <stable@kernel.org>
Signed-off-by: Pawel Laszczak <pawell@cadence.com>
Acked-by: Peter Chen <peter.chen@kernel.org>
Link: https://lore.kernel.org/r/PH7PR07MB9538B55C3A6E71F9ED29E980DD842@PH7PR07MB9538.namprd07.prod.outlook.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 241e2ce88e5a494be7a5d44c0697592f1632fbee upstream.
In very rare cases after resuming controller from L1 to L0 it reads
registers before the clock UTMI have been enabled and as the result
driver reads incorrect value.
Most of registers are in APB domain clock but some of them (e.g. PORTSC)
are in UTMI domain clock.
After entering to L1 state the UTMI clock can be disabled.
When controller transition from L1 to L0 the port status change event is
reported and in interrupt runtime function driver reads PORTSC.
During this read operation controller synchronize UTMI and APB domain
but UTMI clock is still disabled and in result it reads 0xFFFFFFFF value.
To fix this issue driver increases APB timeout value.
The issue is platform specific and if the default value of APB timeout
is not sufficient then this time should be set Individually for each
platform.
Fixes: 3d82904559f4 ("usb: cdnsp: cdns3 Add main part of Cadence USBSSP DRD Driver")
Cc: stable <stable@kernel.org>
Signed-off-by: Pawel Laszczak <pawell@cadence.com>
Acked-by: Peter Chen <peter.chen@kernel.org>
Link: https://lore.kernel.org/r/PH7PR07MB953846C57973E4DB134CAA71DDBF2@PH7PR07MB9538.namprd07.prod.outlook.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 2372f1caeca433c4c01c2482f73fbe057f5168ce upstream.
Currently gadget_wakeup() waits for U0 synchronously if it was
called from func_wakeup(), this is because we need to send the
function wakeup command soon after the link is active. And the
call is made synchronous by polling DSTS continuosly for 20000
times in __dwc3_gadget_wakeup(). But it observed that sometimes
the link is not active even after polling 20K times, leading to
remote wakeup failures. Adding a small delay between each poll
helps, but that won't guarantee resolution in future. Hence make
the gadget_wakeup completely asynchronous.
Since multiple interfaces can issue a function wakeup at once,
add a new variable wakeup_pending_funcs which will indicate the
functions that has issued func_wakup, this is represented in a
bitmap format. If the link is in U3, dwc3_gadget_func_wakeup()
will set the bit corresponding to interface_id and bail out.
Once link comes back to U0, linksts_change irq is triggered,
where the function wakeup command is sent based on bitmap.
Cc: stable <stable@kernel.org>
Fixes: 92c08a84b53e ("usb: dwc3: Add function suspend and function wakeup support")
Signed-off-by: Prashanth K <prashanth.k@oss.qualcomm.com>
Acked-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com>
Link: https://lore.kernel.org/r/20250422103231.1954387-4-prashanth.k@oss.qualcomm.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit a5c7973539b010874a37a0e846e62ac6f00553ba upstream.
Device tree bindings state that the clock is optional for UHCI platform
controllers, and some existing device trees don't provide those - such
as those for VIA/WonderMedia devices.
The driver however fails to probe now if no clock is provided, because
devm_clk_get returns an error pointer in such case.
Switch to devm_clk_get_optional instead, so that it could probe again
on those platforms where no clocks are given.
Cc: stable <stable@kernel.org>
Fixes: 26c502701c52 ("usb: uhci: Add clk support to uhci-platform")
Signed-off-by: Alexey Charkov <alchark@gmail.com>
Link: https://lore.kernel.org/r/20250425-uhci-clock-optional-v1-1-a1d462592f29@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 429a98abfc01d3d4378b7a00969437dc3e8f647c upstream.
We recently added some locking to this function but this error path
was accidentally missed. Unlock before returning.
Fixes: ec27386de23a ("usb: typec: class: Fix NULL pointer access")
Cc: stable <stable@kernel.org>
Signed-off-by: Dan Carpenter <dan.carpenter@linaro.org>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Link: https://lore.kernel.org/r/Z_44tOtmml89wQcM@stanley.mountain
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 9e3a28793d2fde7a709e814d2504652eaba6ae98 upstream.
A Short Packet event before the last TRB of a TD is followed by another
event on the final TRB on spec-compliant HCs, which is most of them.
A 'last_td_was_short' flag was added to know if a TD has just completed
as Short Packet and another event is to come. The flag was cleared after
seeing the event (unless no TDs are pending, but that's a separate bug)
or seeing a new TD complete as something other than Short Packet.
A rework replaced the flag with an 'old_trb_comp_code' variable. When
an event doesn't match the pending TD and the previous event was Short
Packet, the new event is silently ignored.
To preserve old behavior, 'old_trb_comp_code' should be cleared at this
point, but instead it is being set to current comp code, which is often
Short Packet again. This can cause more events to be silently ignored,
even though they are no longer connected with the old TD that completed
short and indicate a serious problem with the driver or the xHC.
Common device classes like UAC in async mode, UVC, serial or the UAS
status pipe complete as Short Packet routinely and could be affected.
Clear 'old_trb_comp_code' to zero, which is an invalid completion code
and the same value the variable starts with. This restores original
behavior on Short Packet and also works for illegal Etron events, which
the code has been extended to cover too.
Fixes: b331a3d8097f ("xhci: Handle spurious events on Etron host isoc enpoints")
Signed-off-by: Michal Pecio <michal.pecio@gmail.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20250410151828.2868740-4-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 66e1a887273c6b89f09bc11a40d0a71d5a081a8e upstream.
To avoid using invalid USB device pointers after a Type-C partner
disconnects, this patch clears the pointers upon partner unregistration.
This ensures a clean state for future connections.
Cc: stable@vger.kernel.org
Fixes: 59de2a56d127 ("usb: typec: Link enumerated USB devices with Type-C partner")
Signed-off-by: Andrei Kuchynski <akuchynski@chromium.org>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Reviewed-by: Benson Leung <bleung@chromium.org>
Link: https://lore.kernel.org/r/20250321143728.4092417-3-akuchynski@chromium.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit ec27386de23a511008c53aa2f3434ad180a3ca9a upstream.
Concurrent calls to typec_partner_unlink_device can lead to a NULL pointer
dereference. This patch adds a mutex to protect USB device pointers and
prevent this issue. The same mutex protects both the device pointers and
the partner device registration.
Cc: stable@vger.kernel.org
Fixes: 59de2a56d127 ("usb: typec: Link enumerated USB devices with Type-C partner")
Signed-off-by: Andrei Kuchynski <akuchynski@chromium.org>
Reviewed-by: Benson Leung <bleung@chromium.org>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Link: https://lore.kernel.org/r/20250321143728.4092417-2-akuchynski@chromium.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit 64eb182d5f7a5ec30227bce4f6922ff663432f44 ]
Compatible "marvell,armada3700-xhci" match data uses the
struct xhci_plat_priv::init_quirk() function pointer to add
XHCI_RESET_ON_RESUME as quirk on XHCI.
Instead, use the struct xhci_plat_priv::quirks field.
Signed-off-by: Théo Lebrun <theo.lebrun@bootlin.com>
Link: https://lore.kernel.org/r/20250205-s2r-cdns-v7-1-13658a271c3c@bootlin.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 8c75f3e6a433d92084ad4e78b029ae680865420f ]
The variable d->name, returned by devm_kasprintf(), could be NULL.
A pointer check is added to prevent potential NULL pointer dereference.
This is similar to the fix in commit 3027e7b15b02
("ice: Fix some null pointer dereference issues in ice_ptp.c").
This issue is found by our static analysis tool
Signed-off-by: Chenyuan Yang <chenyuan0y@gmail.com>
Link: https://lore.kernel.org/r/20250311012705.1233829-1-chenyuan0y@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 28a76fcc4c85dd39633fb96edb643c91820133e3 ]
Nothing prevents a broken HC from claiming that an endpoint is Running
and repeatedly rejecting Stop Endpoint with Context State Error.
Avoid infinite retries and give back cancelled TDs.
No such cases known so far, but HCs have bugs.
Signed-off-by: Michal Pecio <michal.pecio@gmail.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20250311154551.4035726-4-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit b331a3d8097fad4e541d212684192f21fedbd6e5 ]
Unplugging a USB3.0 webcam from Etron hosts while streaming results
in errors like this:
[ 2.646387] xhci_hcd 0000:03:00.0: ERROR Transfer event TRB DMA ptr not part of current TD ep_index 18 comp_code 13
[ 2.646446] xhci_hcd 0000:03:00.0: Looking for event-dma 000000002fdf8630 trb-start 000000002fdf8640 trb-end 000000002fdf8650
[ 2.646560] xhci_hcd 0000:03:00.0: ERROR Transfer event TRB DMA ptr not part of current TD ep_index 18 comp_code 13
[ 2.646568] xhci_hcd 0000:03:00.0: Looking for event-dma 000000002fdf8660 trb-start 000000002fdf8670 trb-end 000000002fdf8670
Etron xHC generates two transfer events for the TRB if an error is
detected while processing the last TRB of an isoc TD.
The first event can be any sort of error (like USB Transaction or
Babble Detected, etc), and the final event is Success.
The xHCI driver will handle the TD after the first event and remove it
from its internal list, and then print an "Transfer event TRB DMA ptr
not part of current TD" error message after the final event.
Commit 5372c65e1311 ("xhci: process isoc TD properly when there was a
transaction error mid TD.") is designed to address isoc transaction
errors, but unfortunately it doesn't account for this scenario.
This issue is similar to the XHCI_SPURIOUS_SUCCESS case where a success
event follows a 'short transfer' event, but the TD the event points to
is already given back.
Expand the spurious success 'short transfer' event handling to cover
the spurious success after error on Etron hosts.
Kuangyi Chiang reported this issue and submitted a different solution
based on using error_mid_td. This commit message is mostly taken
from that patch.
Reported-by: Kuangyi Chiang <ki.chiang65@gmail.com>
Closes: https://lore.kernel.org/linux-usb/20241028025337.6372-6-ki.chiang65@gmail.com/
Tested-by: Kuangyi Chiang <ki.chiang65@gmail.com>
Tested-by: Michal Pecio <michal.pecio@gmail.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20250306144954.3507700-16-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 906dec15b9b321b546fd31a3c99ffc13724c7af4 ]
The TRB pointer of these events points at enqueue at the time of error
occurrence on xHCI 1.1+ HCs or it's NULL on older ones. By the time we
are handling the event, a new TD may be queued at this ring position.
I can trigger this race by rising interrupt moderation to increase IRQ
handling delay. Similar delay may occur naturally due to system load.
If this ever happens after a Missed Service Error, missed TDs will be
skipped and the new TD processed as if it matched the event. It could
be given back prematurely, risking data loss or buffer UAF by the xHC.
Don't complete TDs on xrun events and don't warn if queued TDs don't
match the event's TRB pointer, which can be NULL or a link/no-op TRB.
Don't warn if there are no queued TDs at all.
Now that it's safe, also handle xrun events if the skip flag is clear.
This ensures completion of any TD stuck in 'error mid TD' state right
before the xrun event, which could happen if a driver submits a finite
number of URBs to a buggy HC and then an error occurs on the last TD.
Signed-off-by: Michal Pecio <michal.pecio@gmail.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20250306144954.3507700-6-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit bfa8459942822bdcc86f0e87f237c0723ae64948 ]
Missed Service Error after an error mid TD means that the failed TD has
already been passed by the xHC without acknowledgment of the final TRB,
a known hardware bug. So don't wait any more and give back the TD.
Reproduced on NEC uPD720200 under conditions of ludicrously bad USB link
quality, confirmed to behave as expected using dynamic debug.
Signed-off-by: Michal Pecio <michal.pecio@gmail.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20250306144954.3507700-5-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 461f24bff86808ee5fbfe74751a825f8a7ab24e0 ]
Intel Merrifield SoC uses these endpoints for tracing and they cannot
be re-allocated if being used because the side band flow control signals
are hard wired to certain endpoints:
• 1 High BW Bulk IN (IN#1) (RTIT)
• 1 1KB BW Bulk IN (IN#8) + 1 1KB BW Bulk OUT (Run Control) (OUT#8)
In device mode, since RTIT (EP#1) and EXI/RunControl (EP#8) uses
External Buffer Control (EBC) mode, these endpoints are to be mapped to
EBC mode (to be done by EXI target driver). Additionally TRB for RTIT
and EXI are maintained in STM (System Trace Module) unit and the EXI
target driver will as well configure the TRB location for EP #1 IN
and EP#8 (IN and OUT). Since STM/PTI and EXI hardware blocks manage
these endpoints and interface to OTG3 controller through EBC interface,
there is no need to enable any events (such as XferComplete etc)
for these end points.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Tested-by: Ferry Toth <fntoth@gmail.com>
Acked-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com>
Link: https://lore.kernel.org/r/20250212193116.2487289-5-andriy.shevchenko@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit eafba0205426091354f050381c32ad1567c35844 ]
Prepare the gadget driver to handle the reserved endpoints that will be
not allocated at the initialisation time.
While at it, add a warning where the NULL endpoint should never happen.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Tested-by: Ferry Toth <fntoth@gmail.com>
Acked-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com>
Link: https://lore.kernel.org/r/20250212193116.2487289-3-andriy.shevchenko@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 41d5e3806cf589f658f92c75195095df0b66f66a ]
"maxim,max3421" DT compatible is missing its SPI device ID entry, not
allowing module autoloading and leading to the following message:
"SPI driver max3421-hcd has no spi_device_id for maxim,max3421"
Fix this by adding the spi_device_id table.
Signed-off-by: Alexander Stein <alexander.stein@mailbox.org>
Link: https://lore.kernel.org/r/20250128195114.56321-1-alexander.stein@mailbox.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
commit 73e9cc1ffd3650b12c4eb059dfdafd56e725ceda upstream.
This is not understandable without a comment on endianness
Fixes: afba937e540c9 ("USB: CDC WDM driver")
Cc: stable <stable@kernel.org>
Signed-off-by: Oliver Neukum <oneukum@suse.com>
Link: https://lore.kernel.org/r/20250401084749.175246-5-oneukum@suse.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 1fdc4dca350c0b8ada0b8ebf212504e1ad55e511 upstream.
wdm_wwan_port_tx_complete is called from a completion
handler with irqs disabled and possible in IRQ context
usb_autopm_put_interface can take a mutex.
Hence usb_autopm_put_interface_async must be used.
Fixes: cac6fb015f71 ("usb: class: cdc-wdm: WWAN framework integration")
Cc: stable <stable@kernel.org>
Signed-off-by: Oliver Neukum <oneukum@suse.com>
Link: https://lore.kernel.org/r/20250401084749.175246-4-oneukum@suse.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit c1846ed4eb527bdfe6b3b7dd2c78e2af4bf98f4f upstream.
Clearing WDM_WWAN_IN_USE must be the last action or
we can open a chardev whose URBs are still poisoned
Fixes: cac6fb015f71 ("usb: class: cdc-wdm: WWAN framework integration")
Cc: stable <stable@kernel.org>
Signed-off-by: Oliver Neukum <oneukum@suse.com>
Link: https://lore.kernel.org/r/20250401084749.175246-3-oneukum@suse.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 9697f5efcf5fdea65b8390b5eb81bebe746ceedc upstream.
In case submitting the URB fails we must undo
what we've done so far.
Fixes: cac6fb015f71 ("usb: class: cdc-wdm: WWAN framework integration")
Cc: stable <stable@kernel.org>
Signed-off-by: Oliver Neukum <oneukum@suse.com>
Link: https://lore.kernel.org/r/20250401084749.175246-2-oneukum@suse.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit e00b39a4f3552c730f1e24c8d62c4a8c6aad4e5d upstream.
This device needs the NO_LPM quirk.
Cc: stable <stable@kernel.org>
Signed-off-by: Oliver Neukum <oneukum@suse.com>
Link: https://lore.kernel.org/r/20250408135800.792515-1-oneukum@suse.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 37ffdbd695c02189dbf23d6e7d2385e0299587ca upstream.
The SanDisk 3.2Gen1 Flash Drive, which VID:PID is in 0781:55a3,
just like Silicon Motion Flash Drive:
https://lore.kernel.org/r/20250401023027.44894-1-limiao870622@163.com
also needs the DELAY_INIT quirk, or it will randomly work incorrectly
(e.g.: lsusb and can't list this device info) when connecting Huawei
hisi platforms and doing thousand of reboot test circles.
Cc: stable <stable@kernel.org>
Signed-off-by: Miao Li <limiao@kylinos.cn>
Signed-off-by: Lei Huang <huanglei@kylinos.cn>
Link: https://lore.kernel.org/r/20250414062935.159024-1-limiao870622@163.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 2932b6b547ec36ad2ed60fbf2117c0e46bb7d40a upstream.
Silicon Motion Flash Drive connects to Huawei hisi platforms and
performs a system reboot test for two thousand circles, it will
randomly work incorrectly on boot, set DELAY_INIT quirk can workaround
this issue.
Signed-off-by: Miao Li <limiao@kylinos.cn>
Cc: stable <stable@kernel.org>
Link: https://lore.kernel.org/r/20250401023027.44894-1-limiao870622@163.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 38d6e60b6f3a99f8f13bee22eab616136c2c0675 upstream.
The "reset" GPIO controls the RESET signal to an external, usually
ULPI PHY, chip. The original code path acquires the signal in LOW
state, and then immediately asserts it HIGH again, if the reset
signal defaulted to asserted, there'd be a short "spike" before the
reset.
Here is what happens depending on the pre-existing state of the reset
signal:
Reset (previously asserted): ~~~|_|~~~~|_______
Reset (previously deasserted): _____|~~~~|_______
^ ^ ^
A B C
At point A, the low going transition is because the reset line is
requested using GPIOD_OUT_LOW. If the line is successfully requested,
the first thing we do is set it high _without_ any delay. This is
point B. So, a glitch occurs between A and B.
Requesting the line using GPIOD_OUT_HIGH eliminates the A and B
transitions. Instead we get:
Reset (previously asserted) : ~~~~~~~~~~|______
Reset (previously deasserted): ____|~~~~~|______
^ ^
A C
Where A and C are the points described above in the code. Point B
has been eliminated.
The issue was found during code inspection.
Also remove the cryptic "toggle ulpi .." comment.
Fixes: ca05b38252d7 ("usb: dwc3: xilinx: Add gpio-reset support")
Cc: stable <stable@kernel.org>
Signed-off-by: Mike Looijmans <mike.looijmans@topic.nl>
Reviewed-by: Radhey Shyam Pandey <radhey.shyam.pandey@amd.com>
Acked-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com>
Link: https://lore.kernel.org/r/20250318064518.9320-1-mike.looijmans@topic.nl
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 63ccd26cd1f6600421795f6ca3e625076be06c9f upstream.
The event count is read from register DWC3_GEVNTCOUNT.
There is a check for the count being zero, but not for exceeding the
event buffer length.
Check that event count does not exceed event buffer length,
avoiding an out-of-bounds access when memcpy'ing the event.
Crash log:
Unable to handle kernel paging request at virtual address ffffffc0129be000
pc : __memcpy+0x114/0x180
lr : dwc3_check_event_buf+0xec/0x348
x3 : 0000000000000030 x2 : 000000000000dfc4
x1 : ffffffc0129be000 x0 : ffffff87aad60080
Call trace:
__memcpy+0x114/0x180
dwc3_interrupt+0x24/0x34
Signed-off-by: Frode Isaksen <frode@meta.com>
Fixes: 72246da40f37 ("usb: Introduce DesignWare USB3 DRD Driver")
Cc: stable <stable@kernel.org>
Acked-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com>
Link: https://lore.kernel.org/r/20250403072907.448524-1-fisaksen@baylibre.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit bcb60d438547355b8f9ad48645909139b64d3482 upstream.
The OHCI controller (rev 0x02) under LS7A PCI host has a hardware flaw.
MMIO register with offset 0x60/0x64 is treated as legacy PS2-compatible
keyboard/mouse interface, which confuse the OHCI controller. Since OHCI
only use a 4KB BAR resource indeed, the LS7A OHCI controller's 32KB BAR
is wrapped around (the second 4KB BAR space is the same as the first 4KB
internally). So we can add an 4KB offset (0x1000) to the OHCI registers
(from the PCI BAR resource) as a quirk.
Cc: stable <stable@kernel.org>
Suggested-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Alan Stern <stern@rowland.harvard.edu>
Tested-by: Mingcong Bai <baimingcong@loongson.cn>
Signed-off-by: Huacai Chen <chenhuacai@loongson.cn>
Link: https://lore.kernel.org/r/20250328040059.3672979-1-chenhuacai@loongson.cn
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 8c531e0a8c2d82509ad97c6d3a1e6217c7ed136d upstream.
usb_phy_init() may return an error code if e.g. its implementation fails
to prepare/enable some clocks. And properly rollback on probe error path
by calling the counterpart usb_phy_shutdown().
Found by Linux Verification Center (linuxtesting.org).
Fixes: be9cae2479f4 ("usb: chipidea: imx: Fix ULPI on imx53")
Cc: stable <stable@kernel.org>
Signed-off-by: Fedor Pchelkin <pchelkin@ispras.ru>
Acked-by: Peter Chen <peter.chen@kernel.org>
Link: https://lore.kernel.org/r/20250316102658.490340-4-pchelkin@ispras.ru
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 8cab0e9a3f3e8d700179e0d6141643d54a267fd5 upstream.
Upon encountering errors during the HSIC pinctrl handling section the
regulator should be disabled.
Use devm_add_action_or_reset() to let the regulator-disabling routine be
handled by device resource management stack.
Found by Linux Verification Center (linuxtesting.org).
Fixes: 4d6141288c33 ("usb: chipidea: imx: pinctrl for HSIC is optional")
Cc: stable <stable@kernel.org>
Signed-off-by: Fedor Pchelkin <pchelkin@ispras.ru>
Acked-by: Peter Chen <peter.chen@kernel.org>
Link: https://lore.kernel.org/r/20250316102658.490340-3-pchelkin@ispras.ru
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 4e28f79e3dffa52d327b46d1a78dac16efb5810b upstream.
usbmisc is an optional device property so it is totally valid for the
corresponding data->usbmisc_data to have a NULL value.
Check that before dereferencing the pointer.
Found by Linux Verification Center (linuxtesting.org) with Svace static
analysis tool.
Fixes: 74adad500346 ("usb: chipidea: ci_hdrc_imx: decrement device's refcount in .remove() and in the error path of .probe()")
Cc: stable <stable@kernel.org>
Signed-off-by: Fedor Pchelkin <pchelkin@ispras.ru>
Acked-by: Peter Chen <peter.chen@kernel.org>
Link: https://lore.kernel.org/r/20250316102658.490340-2-pchelkin@ispras.ru
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit a1059896f2bfdcebcdc7153c3be2307ea319501f upstream.
The cdns3 driver has the same NCM deadlock as fixed in cdnsp by commit
58f2fcb3a845 ("usb: cdnsp: Fix deadlock issue during using NCM gadget").
Under PREEMPT_RT the deadlock can be readily triggered by heavy network
traffic, for example using "iperf --bidir" over NCM ethernet link.
The deadlock occurs because the threaded interrupt handler gets
preempted by a softirq, but both are protected by the same spinlock.
Prevent deadlock by disabling softirq during threaded irq handler.
Cc: stable <stable@kernel.org>
Fixes: 7733f6c32e36 ("usb: cdns3: Add Cadence USB3 DRD Driver")
Signed-off-by: Ralph Siemsen <ralph.siemsen@linaro.org>
Acked-by: Peter Chen <peter.chen@kernel.org>
Reviewed-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Link: https://lore.kernel.org/r/20250318-rfs-cdns3-deadlock-v2-1-bfd9cfcee732@linaro.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 1ea050da5562af9b930d17cbbe9632d30f5df43a upstream.
This check is performed before prepare_transfer() and prepare_ring(), so
enqueue can already point at the final link TRB of a segment. And indeed
it will, some 0.4% of times this code is called.
Then enqueue + 1 is an invalid pointer. It will crash the kernel right
away or load some junk which may look like a link TRB and cause the real
link TRB to be replaced with a NOOP. This wouldn't end well.
Use a functionally equivalent test which doesn't dereference the pointer
and always gives correct result.
Something has crashed my machine twice in recent days while playing with
an Etron HC, and a control transfer stress test ran for confirmation has
just crashed it again. The same test passes with this patch applied.
Fixes: 5e1c67abc930 ("xhci: Fix control transfer error on Etron xHCI host")
Cc: stable@vger.kernel.org
Signed-off-by: Michal Pecio <michal.pecio@gmail.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Reviewed-by: Kuangyi Chiang <ki.chiang65@gmail.com>
Link: https://lore.kernel.org/r/20250410151828.2868740-5-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit bea5892d0ed274e03655223d1977cf59f9aff2f2 upstream.
Current xhci bus resume implementation prevents xHC host from generating
interrupts during high-speed USB 2 and super-speed USB 3 bus resume.
Only reason to disable interrupts during bus resume would be to prevent
the interrupt handler from interfering with the resume process of USB 2
ports.
Host initiated resume of USB 2 ports is done in two stages.
The xhci driver first transitions the port from 'U3' to 'Resume' state,
then wait in Resume for 20ms, and finally moves port to U0 state.
xhci driver can't prevent interrupts by keeping the xhci spinlock
due to this 20ms sleep.
Limit interrupt disabling to the USB 2 port resume case only.
resuming USB 2 ports in bus resume is only done in special cases where
USB 2 ports had to be forced to suspend during bus suspend.
The current way of preventing interrupts by clearing the 'Interrupt
Enable' (INTE) bit in USBCMD register won't prevent the Interrupter
registers 'Interrupt Pending' (IP), 'Event Handler Busy' (EHB) and
USBSTS register Event Interrupt (EINT) bits from being set.
New interrupts can't be issued before those bits are properly clered.
Disable interrupts by clearing the interrupter register 'Interrupt
Enable' (IE) bit instead. This way IP, EHB and INTE won't be set
before IE is enabled again and a new interrupt is triggered.
Reported-by: Devyn Liu <liudingyuan@huawei.com>
Closes: https://lore.kernel.org/linux-usb/b1a9e2d51b4d4ff7a304f77c5be8164e@huawei.com/
Cc: stable@vger.kernel.org
Tested-by: Devyn Liu <liudingyuan@huawei.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20250410151828.2868740-6-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 4cc01410e1c1dd075df10f750775c81d1cb6672b upstream.
Add serial support for OWON HDS200 series oscilloscopes and likely
many other pieces of OWON test equipment.
OWON HDS200 series devices host two USB endpoints, designed to
facilitate bidirectional SCPI. SCPI is a predominately ASCII text
protocol for test/measurement equipment. Having a serial/tty interface
for these devices lowers the barrier to entry for anyone trying to
write programs to communicate with them.
The following shows the USB descriptor for the OWON HDS272S running
firmware V5.7.1:
Bus 001 Device 068: ID 5345:1234 Owon PDS6062T Oscilloscope
Negotiated speed: Full Speed (12Mbps)
Device Descriptor:
bLength 18
bDescriptorType 1
bcdUSB 2.00
bDeviceClass 0 [unknown]
bDeviceSubClass 0 [unknown]
bDeviceProtocol 0
bMaxPacketSize0 64
idVendor 0x5345 Owon
idProduct 0x1234 PDS6062T Oscilloscope
bcdDevice 1.00
iManufacturer 1 oscilloscope
iProduct 2 oscilloscope
iSerial 3 oscilloscope
bNumConfigurations 1
Configuration Descriptor:
bLength 9
bDescriptorType 2
wTotalLength 0x0029
bNumInterfaces 1
bConfigurationValue 1
iConfiguration 0
bmAttributes 0x80
(Bus Powered)
MaxPower 100mA
Interface Descriptor:
bLength 9
bDescriptorType 4
bInterfaceNumber 0
bAlternateSetting 0
bNumEndpoints 2
bInterfaceClass 5 Physical Interface Device
bInterfaceSubClass 0 [unknown]
bInterfaceProtocol 0
iInterface 0
** UNRECOGNIZED: 09 21 11 01 00 01 22 5f 00
Endpoint Descriptor:
bLength 7
bDescriptorType 5
bEndpointAddress 0x81 EP 1 IN
bmAttributes 2
Transfer Type Bulk
Synch Type None
Usage Type Data
wMaxPacketSize 0x0040 1x 64 bytes
bInterval 32
Endpoint Descriptor:
bLength 7
bDescriptorType 5
bEndpointAddress 0x01 EP 1 OUT
bmAttributes 2
Transfer Type Bulk
Synch Type None
Usage Type Data
wMaxPacketSize 0x0040 1x 64 bytes
bInterval 32
Device Status: 0x0000
(Bus Powered)
OWON appears to be using the same USB Vendor and Product ID for many
of their oscilloscopes. Looking at the discussion about the USB
vendor/product ID, in the link bellow, suggests that this VID/PID is
shared with VDS, SDS, PDS, and now the HDS series oscilloscopes.
Available documentation for these devices seems to indicate that all
use a similar SCPI protocol, some with RS232 options. It is likely that
this same simple serial setup would work correctly for them all.
Link: https://usb-ids.gowdy.us/read/UD/5345/1234
Signed-off-by: Craig Hesling <craig@hesling.com>
Cc: stable@vger.kernel.org
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 968e1cbb1f6293c3add9607f80b5ce3d29f57583 upstream.
Add Sierra Wireless EM9291.
Interface 0: MBIM control
1: MBIM data
3: AT port
4: Diagnostic port
T: Bus=01 Lev=01 Prnt=01 Port=00 Cnt=01 Dev#= 2 Spd=480 MxCh= 0
D: Ver= 2.10 Cls=00(>ifc ) Sub=00 Prot=00 MxPS=64 #Cfgs= 1
P: Vendor=1199 ProdID=90e3 Rev=00.06
S: Manufacturer=Sierra Wireless, Incorporated
S: Product=Sierra Wireless EM9291
S: SerialNumber=xxxxxxxxxxxxxxxx
C: #Ifs= 4 Cfg#= 1 Atr=a0 MxPwr=500mA
I: If#= 0 Alt= 0 #EPs= 1 Cls=02(commc) Sub=0e Prot=00 Driver=cdc_mbim
E: Ad=81(I) Atr=03(Int.) MxPS= 64 Ivl=32ms
I: If#= 1 Alt= 1 #EPs= 2 Cls=0a(data ) Sub=00 Prot=02 Driver=cdc_mbim
E: Ad=0f(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=8e(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
I: If#= 3 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=ff Prot=40 Driver=(none)
E: Ad=01(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=82(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=83(I) Atr=03(Int.) MxPS= 10 Ivl=32ms
I: If#= 4 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=30 Driver=(none)
E: Ad=02(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=84(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
Signed-off-by: Adam Xue <zxue@semtech.com>
Cc: stable@vger.kernel.org
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit b399078f882b6e5d32da18b6c696cc84b12f90d5 upstream.
Abacus Electrics makes optical probes for interacting with smart meters
over an optical interface.
At least one version uses an FT232B chip (as detected by ftdi_sio) with
a custom USB PID, which needs to be added to the list to make the device
work in a plug-and-play fashion.
Signed-off-by: Michael Ehrenreich <michideep@gmail.com>
Cc: stable@vger.kernel.org
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
