| Age | Commit message (Collapse) | Author |
|---|
|
If an frame was transmitted incomplete to the host, we set the
UVC_STREAM_ERR bit in the header for the last request that is going
to be queued. This way the host will know that it should drop the
frame instead of trying to display the corrupted content.
Signed-off-by: Michael Grzeschik <m.grzeschik@pengutronix.de>
Link: https://lore.kernel.org/r/20240214-uvc-error-tag-v1-2-37659a3877fe@pengutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
If the request that was missed was zero bytes long, it
is likely that the overall transferred frame was not affected.
So don't flag the frame incomplete in that case.
Signed-off-by: Michael Grzeschik <m.grzeschik@pengutronix.de>
Link: https://lore.kernel.org/r/20240214-uvc-error-tag-v1-1-37659a3877fe@pengutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
We refactor the complete handler since the return path with the
locking are really difficult to follow. Just simplify the function by
switching the logic return it on an disabled endpoint early. This way
the second level of indentation can be removed.
Signed-off-by: Michael Grzeschik <m.grzeschik@pengutronix.de>
Link: https://lore.kernel.org/r/20240214-uvc-gadget-cleanup-v1-3-de6d78780459@pengutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
By toggling the condition check for a valid buffer, the else path
can be completely avoided.
Signed-off-by: Michael Grzeschik <m.grzeschik@pengutronix.de>
Link: https://lore.kernel.org/r/20240214-uvc-gadget-cleanup-v1-2-de6d78780459@pengutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
The pump function is running in an while(1) loop. The only case this
loop will be escaped is the two breaks. In both cases the req is valid.
Therefor the check for an not set req can be dropped and setting the req
to NULL does also has never any effect.
Signed-off-by: Michael Grzeschik <m.grzeschik@pengutronix.de>
Link: https://lore.kernel.org/r/20240214-uvc-gadget-cleanup-v1-1-de6d78780459@pengutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
This is probable useful information to have in user space in
general, but it's primarily needed for the xHCI DbC (Debug
Capability). When xHCI DbC is being used, the USB port needs
to be muxed to the xHCI even in device role. In xHCI DbC mode,
the xHCI is the USB device controller.
Tested-by: Uday Bhat <uday.m.bhat@intel.com>
Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Reviewed-by: Prashant Malani <pmalani@chromium.org>
Link: https://lore.kernel.org/r/20240213130018.3029991-2-heikki.krogerus@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
The variable retval is being assigned a value that is not being read
and is being re-assigned a new value a couple of statements later.
The assignment is redundant and can be removed.
Cleans up clang scan warning:
drivers/usb/image/mdc800.c:634:2: warning: Value stored to 'retval'
is never read [deadcode.DeadStores]
Signed-off-by: Colin Ian King <colin.i.king@gmail.com>
Link: https://lore.kernel.org/r/20240207113730.2444296-1-colin.i.king@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
The variable offset is being assigned a value that is not being read
afterwards, the assignment is redundant and can be removed.
Cleans up clang scan warning:
drivers/usb/storage/freecom.c:537:2: warning: Value stored to 'offset'
is never read [deadcode.DeadStores]
Signed-off-by: Colin Ian King <colin.i.king@gmail.com>
Link: https://lore.kernel.org/r/20240207112208.2443237-1-colin.i.king@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Replace the self-rolled implementations with kstrtobool(). This reduces
the maintenance efforts in the future.
Signed-off-by: Guan-Yu Lin <guanyulin@google.com>
Link: https://lore.kernel.org/r/20240202030301.2396374-1-guanyulin@google.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
This patch introduces three new ioctls. They all should be called on a
data endpoint (ie. not ep0). They are:
- FUNCTIONFS_DMABUF_ATTACH, which takes the file descriptor of a DMABUF
object to attach to the endpoint.
- FUNCTIONFS_DMABUF_DETACH, which takes the file descriptor of the
DMABUF to detach from the endpoint. Note that closing the endpoint's
file descriptor will automatically detach all attached DMABUFs.
- FUNCTIONFS_DMABUF_TRANSFER, which requests a data transfer from / to
the given DMABUF. Its argument is a structure that packs the DMABUF's
file descriptor, the size in bytes to transfer (which should generally
be set to the size of the DMABUF), and a 'flags' field which is unused
for now.
Before this ioctl can be used, the related DMABUF must be attached
with FUNCTIONFS_DMABUF_ATTACH.
These three ioctls enable the FunctionFS code to transfer data between
the USB stack and a DMABUF object, which can be provided by a driver
from a completely different subsystem, in a zero-copy fashion.
Signed-off-by: Paul Cercueil <paul@crapouillou.net>
Acked-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Acked-by: Christian König <christian.koenig@amd.com>
Link: https://lore.kernel.org/r/20240130122340.54813-4-paul@crapouillou.net
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
This exact same code was duplicated in two different places.
Signed-off-by: Paul Cercueil <paul@crapouillou.net>
Link: https://lore.kernel.org/r/20240130122340.54813-3-paul@crapouillou.net
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Add a new 'sg_was_mapped' field to the struct usb_request. This field
can be used to indicate that the scatterlist associated to the USB
transfer has already been mapped into the DMA space, and it does not
have to be done internally.
Signed-off-by: Paul Cercueil <paul@crapouillou.net>
Link: https://lore.kernel.org/r/20240130122340.54813-2-paul@crapouillou.net
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Remove 'snps,host-vbus-glitches-quirk' and apply workaround
unconditionally.
It is safer to keep vbus disabled before handing over to xhci driver. So
needn't 'snps,host-vbus-glitches' property to enable it and apply it
unconditionally.
Remove all host_vbus_glitches variable and call
dwc3_power_off_all_roothub_ports() directly.
Signed-off-by: Frank Li <Frank.Li@nxp.com>
Acked-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com>
Acked-by: Conor Dooley <conor.dooley@microchip.com>
Link: https://lore.kernel.org/r/20240212-vbus-glitch-v2-2-d71b73a82de1@nxp.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
The ioremap() function doesn't return error pointers, it returns NULL on
error. Update the check.
Fixes: 2d2a3349521d ("usb: dwc3: Add workaround for host mode VBUS glitch when boot")
Signed-off-by: Dan Carpenter <dan.carpenter@linaro.org>
Acked-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com>
Link: https://lore.kernel.org/r/71499112-4ed3-489a-9a56-b4a8ab89cd05@moroto.mountain
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
The pointer trb is being assigned a value that is not being
read afterwards, it is being re-assigned later inside a for_each_sg
loop. The assignment is redundant and can be removed.
Cleans up clang scan warning:
drivers/usb/dwc3/gadget.c:3432:19: warning: Value stored to 'trb'
during its initialization is never read [deadcode.DeadStores]
Signed-off-by: Colin Ian King <colin.i.king@gmail.com>
Acked-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com>
Link: https://lore.kernel.org/r/20240207120319.2445123-1-colin.i.king@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
The driver dwc3 deviates from the programming guide in regard to
endpoint configuration. It does this command sequence:
DEPSTARTCFG -> DEPXFERCFG -> DEPCFG
Instead of the suggested flow:
DEPSTARTCFG -> DEPCFG -> DEPXFERCFG
The reasons for this deviation were as follow, quoted:
1) The databook says to do %DWC3_DEPCMD_DEPSTARTCFG for every
%USB_REQ_SET_CONFIGURATION and %USB_REQ_SET_INTERFACE
(8.1.5). This is incorrect in the scenario of multiple
interfaces.
2) The databook does not mention doing more
%DWC3_DEPCMD_DEPXFERCFG for new endpoint on alt setting
(8.1.6).
Regarding 1), DEPSTARTCFG resets the endpoints' resource and can be a
problem if used with SET_INTERFACE request of a multiple interface
configuration. But we can still satisfy the programming guide
requirement by assigning the endpoint resource as part of
usb_ep_enable(). We will only reset endpoint resources on controller
initialization and SET_CONFIGURATION request.
Regarding 2), the later versions of the programming guide were updated
to clarify this flow (see "Alternate Initialization on SetInterface
Request" of the programming guide). As long as the platform has enough
physical endpoints, we can assign resource to a new endpoint.
The order of the command sequence will not be a problem to most
platforms for the current implementation of the dwc3 driver. However,
this order is required in different scenarios (such as initialization
during controller's hibernation restore). Let's keep the flow consistent
and follow the programming guide.
Signed-off-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com>
Link: https://lore.kernel.org/r/c143583a5afb087deb8c3aa5eb227ee23515f272.1706754219.git.Thinh.Nguyen@synopsys.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Update the default USB device authorization mode help text so that the
meaning of the option and it's available values are described more
accurately.
Reported-by: Geert Uytterhoeven <geert@linux-m68k.org>
Closes: https://lore.kernel.org/linux-usb/CAMuHMdUy793gzDVR0jfNnx5TUdJ_2MKH5NPGSgHkytAhArtqmw@mail.gmail.com/
Signed-off-by: Niko Mauno <niko.mauno@vaisala.com>
Link: https://lore.kernel.org/r/20240213124518.20231-1-niko.mauno@vaisala.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Expose xhci_stop_endpoint_sync() which is a synchronous variant of
xhci_queue_stop_endpoint(). This is useful for client drivers that are
using the secondary interrupters, and need to stop/clean up the current
session. The stop endpoint command handler will also take care of cleaning
up the ring.
Modifications to repurpose the new API into existing stop endpoint
sequences was implemented by Wesley Cheng.
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Co-developed-by: Wesley Cheng <quic_wcheng@quicinc.com>
Signed-off-by: Wesley Cheng <quic_wcheng@quicinc.com>
Link: https://lore.kernel.org/r/20240217001017.29969-11-quic_wcheng@quicinc.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Some sequences, will require traversing through the entire event ring
without handling the event TRB. This is ideal for when secondary
interrupters that are utilized by external entities need to clean up the
interrupter's event rings during halting of the XHCI HCD.
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Wesley Cheng <quic_wcheng@quicinc.com>
Link: https://lore.kernel.org/r/20240217001017.29969-10-quic_wcheng@quicinc.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Check if the event ring exists and is valid once when the event handler
is called, not before every individual event TRB.
At this point the interrupter is valid, so no need to check that.
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Wesley Cheng <quic_wcheng@quicinc.com>
Link: https://lore.kernel.org/r/20240217001017.29969-9-quic_wcheng@quicinc.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Add unhandled_event_trb() that returns true in case xHC hardware has
written new event trbs to the event ring that driver has not yet handled.
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Wesley Cheng <quic_wcheng@quicinc.com>
Link: https://lore.kernel.org/r/20240217001017.29969-8-quic_wcheng@quicinc.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Split the main XHCI interrupt handler into a different API, so that other
potential interrupters can utilize similar event ring handling. A scenario
would be if a secondary interrupter required to skip pending events in the
event ring, which would warrant a similar set of operations.
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Wesley Cheng <quic_wcheng@quicinc.com>
Link: https://lore.kernel.org/r/20240217001017.29969-7-quic_wcheng@quicinc.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
The event ring dequeue pointer field (ERDP) in xHC hardware is used to
inform controller how far the driver has processed events on the event
ring.
In the case all events are handled and event ring is empty then the
address of the TRB after the last processed one should be written.
This TRB is both the enqueue and dequeue pointer.
But in case we are writing the ERDP in the middle of processing
several events then ERDP field should be written with the "up to and
including" address of the last handled event TRB.
Currenly each ERDP write by driver is done as if all events are handled
and ring is empty.
Fix this by adjusting the order when software dequeue "inc_deq()"
is called and hardware dequeue "xhci_update_erst_dequeue()" is updated.
Details in xhci 1.2 specification section 4.9.4:
"System software shall write the Event Ring Dequeue Pointer (ERDP)
register to inform the xHC that it has completed the processing of Event
TRBs up to and including the Event TRB referenced by the ERDP.
The detection of a Cycle bit mismatch in an Event TRB processed by
software indicates the location of the xHC Event Ring Enqueue Pointer
and that the Event Ring is empty. Software shall write the ERDP with
the address of this TRB to indicate that it has processed all Events
in the ring"
This change depends on fixes made to relocate inc_deq() calls captured
in the below commits:
commit 3321f84bfae0 ("xhci: simplify event ring dequeue tracking for
transfer events")
commit d1830364e963 ("xhci: Simplify event ring dequeue pointer update
for port change events")
Fixes: dc0ffbea5729 ("usb: host: xhci: update event ring dequeue pointer on purpose")
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Wesley Cheng <quic_wcheng@quicinc.com>
Link: https://lore.kernel.org/r/20240217001017.29969-6-quic_wcheng@quicinc.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
The event_ring_deq parameter is used to check if the event ring dequeue
position is updated while calling by xhci_handle_event(), meaning there was
an actual event on the ring to handle. In this case the driver needs to
inform hardware about the updated dequeue position.
Basically event_ring_deq just stores the old event ring dequeue position
before calling the event handler.
Keeping track of software event dequeue updates this way is no longer
useful as driver anyways reads the current hardware dequeue position
within the handle event, and checks if it needs to be updated.
The driver might anyway need to modify the EHB (event handler busy) bit in
the same register as the dequeue pointer even if the actual dequeue
position did not change.
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Wesley Cheng <quic_wcheng@quicinc.com>
Link: https://lore.kernel.org/r/20240217001017.29969-5-quic_wcheng@quicinc.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
isoc_bei_interval is used to balance how often completed isochronous
events cause interrupts. If interval is too large then the event ring
may fill up before the completed isoc TRBs are handled.
isoc_bei_interval is tuned based on how full the event ring is.
isoc_bei_interval variable needs to be per interrupter as
with several interrupters each one has its own event ring.
move isoc_bei_interval variable to the interrupter structure.
if a secondary interrupter does not care about this feature then
keep isoc_bei_interval 0.
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Wesley Cheng <quic_wcheng@quicinc.com>
Link: https://lore.kernel.org/r/20240217001017.29969-4-quic_wcheng@quicinc.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Add a helper to set the interrupt moderation interval for an interrupter.
Each interrupter can have its own moderation value.
Hardware has a 16bit register for the moderation value, each step is 250ns.
Helper function imod_interval argument is in nanoseconds.
Values from 0 to 16383750 (250 x 0xffff) are accepted.
0 means no interrupt throttling.
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Wesley Cheng <quic_wcheng@quicinc.com>
Link: https://lore.kernel.org/r/20240217001017.29969-3-quic_wcheng@quicinc.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Each interrupter has an interrupt pending (IP) bit that should be cleared
in the interrupt handler. This is done automatically for systems using
MSI/MSI-X interrupts.
Secondary interrupters used by audio offload may not actually trigger
MSI/MSI-X messages, so driver may need to clear the IP bit manually for
these, even if the primary interrupter IP is cleared automatically.
Add an ip_autoclear flag to each interrupter that driver can configure
when requesting an interrupt for that xHC interrupter, and move
the interrupt pending clearing code to its own helper function.
Use this ip_autoclear flag instead of the current hcd->msi_enabled
to check if IP flag is cleared by software.
[Moved ip_autoclear into xhci and set based on msi_enabled -wcheng]
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Wesley Cheng <quic_wcheng@quicinc.com>
Link: https://lore.kernel.org/r/20240217001017.29969-2-quic_wcheng@quicinc.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
It has been observed that some USB/UAS devices return generic properties
hardcoded in firmware for mode pages for a period of time after a device
has been discovered. The reported properties are either garbage or they do
not accurately reflect the characteristics of the physical storage device
attached in the case of a bridge.
Prior to commit 1e029397d12f ("scsi: sd: Reorganize DIF/DIX code to
avoid calling revalidate twice") we would call revalidate several
times during device discovery. As a result, incorrect values would
eventually get replaced with ones accurately describing the attached
storage. When we did away with the redundant revalidate pass, several
cases were reported where devices reported nonsensical values or would
end up in write-protected state.
An initial attempt at addressing this issue involved introducing a
delayed second revalidate invocation. However, this approach still
left some devices reporting incorrect characteristics.
Tasos Sahanidis debugged the problem further and identified that
introducing a READ operation prior to MODE SENSE fixed the problem and that
it wasn't a timing issue. Issuing a READ appears to cause the devices to
update their state to reflect the actual properties of the storage
media. Device properties like vendor, model, and storage capacity appear to
be correctly reported from the get-go. It is unclear why these devices
defer populating the remaining characteristics.
Match the behavior of a well known commercial operating system and
trigger a READ operation prior to querying device characteristics to
force the device to populate the mode pages.
The additional READ is triggered by a flag set in the USB storage and
UAS drivers. We avoid issuing the READ for other transport classes
since some storage devices identify Linux through our particular
discovery command sequence.
Link: https://lore.kernel.org/r/20240213143306.2194237-1-martin.petersen@oracle.com
Fixes: 1e029397d12f ("scsi: sd: Reorganize DIF/DIX code to avoid calling revalidate twice")
Cc: stable@vger.kernel.org
Reported-by: Tasos Sahanidis <tasos@tasossah.com>
Reviewed-by: Ewan D. Milne <emilne@redhat.com>
Reviewed-by: Bart Van Assche <bvanassche@acm.org>
Tested-by: Tasos Sahanidis <tasos@tasossah.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
This reverts commit 398aa9a7e77cf23c2a6f882ddd3dcd96f21771dc.
The update to the gadget API to support EBC feature is incomplete. It's
missing at least the following:
* New usage documentation
* Gadget capability check
* Condition for the user to check how many and which endpoints can be
used as "fifo_mode"
* Description of how it can affect completed request (e.g. dwc3 won't
update TRB on completion -- ie. how it can affect request's actual
length report)
Let's revert this until it's ready.
Fixes: 398aa9a7e77c ("usb: dwc3: Support EBC feature of DWC_usb31")
Signed-off-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com>
Link: https://lore.kernel.org/r/3042f847ff904b4dd4e4cf66a1b9df470e63439e.1707441690.git.Thinh.Nguyen@synopsys.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
In commit 8caab75fd2c2 ("spi: Generalize SPI "master" to "controller"")
some functions and struct members were renamed. To not break all drivers
compatibility macros were provided.
To be able to remove these compatibility macros push the renaming into
this driver.
Reviewed-by: Herve Codina <herve.codina@bootlin.com>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Acked-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Link: https://lore.kernel.org/r/5caf03b6f321a9870aabb9282f1f22211d052740.1707324794.git.u.kleine-koenig@pengutronix.de
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
The QCM6490 Linux Android firmware needs this workaround as well. Add it
to the list.
Acked-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Signed-off-by: Luca Weiss <luca.weiss@fairphone.com>
Link: https://lore.kernel.org/r/20240208-fp5-pmic-glink-v2-2-4837d4abd5a4@fairphone.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
The only generic interface to execute asynchronously in the BH context is
tasklet; however, it's marked deprecated and has some design flaws. To
replace tasklets, BH workqueue support was recently added. A BH workqueue
behaves similarly to regular workqueues except that the queued work items
are executed in the BH context.
This patch converts usb hcd from tasklet to BH workqueue.
Signed-off-by: Tejun Heo <tj@kernel.org>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Alan Stern <stern@rowland.harvard.edu>
Cc: linux-usb@vger.kernel.org
|
|
We need the USB fixes in here as well.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
https://git.kernel.org/pub/scm/linux/kernel/git/johan/usb-serial into usb-linus
Johan writes:
USB-serial device ids for 6.8-rc3
Here are some new device ids for 6.8-rc3.
All have been in linux-next with no reported issues.
* tag 'usb-serial-6.8-rc3' of https://git.kernel.org/pub/scm/linux/kernel/git/johan/usb-serial:
USB: serial: option: add Fibocom FM101-GL variant
USB: serial: qcserial: add new usb-id for Dell Wireless DW5826e
USB: serial: cp210x: add ID for IMST iM871A-USB
|
|
Update the USB serial option driver support for the Fibocom
FM101-GL
LTE modules as there are actually several different variants.
- VID:PID 2cb7:01a3, FM101-GL are laptop M.2 cards (with
MBIM interfaces for /Linux/Chrome OS)
0x01a3:mbim,gnss
Here are the outputs of usb-devices:
T: Bus=04 Lev=01 Prnt=01 Port=00 Cnt=01 Dev#= 3 Spd=5000 MxCh= 0
D: Ver= 3.20 Cls=00(>ifc ) Sub=00 Prot=00 MxPS= 9 #Cfgs= 1
P: Vendor=2cb7 ProdID=01a3 Rev=05.04
S: Manufacturer=Fibocom Wireless Inc.
S: Product=Fibocom FM101-GL Module
S: SerialNumber=5ccd5cd4
C: #Ifs= 3 Cfg#= 1 Atr=a0 MxPwr=896mA
I: If#= 0 Alt= 0 #EPs= 1 Cls=02(commc) Sub=0e Prot=00 Driver=cdc_mbim
E: Ad=81(I) Atr=03(Int.) MxPS= 64 Ivl=32ms
I: If#= 1 Alt= 1 #EPs= 2 Cls=0a(data ) Sub=00 Prot=02 Driver=cdc_mbim
E: Ad=0f(O) Atr=02(Bulk) MxPS=1024 Ivl=0ms
E: Ad=8e(I) Atr=02(Bulk) MxPS=1024 Ivl=0ms
I: If#= 2 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=00 Prot=40 Driver=option
E: Ad=01(O) Atr=02(Bulk) MxPS=1024 Ivl=0ms
E: Ad=82(I) Atr=02(Bulk) MxPS=1024 Ivl=0ms
E: Ad=83(I) Atr=03(Int.) MxPS= 10 Ivl=32ms
Signed-off-by: Puliang Lu <puliang.lu@fibocom.com>
Cc: stable@vger.kernel.org
Signed-off-by: Johan Hovold <johan@kernel.org>
|
|
Add support for Dell DW5826e with USB-id 0x413c:0x8217 & 0x413c:0x8218.
It is 0x413c:0x8217
T: Bus=02 Lev=01 Prnt=01 Port=05 Cnt=01 Dev#= 4 Spd=480 MxCh= 0
D: Ver= 2.10 Cls=ef(misc ) Sub=02 Prot=01 MxPS=64 #Cfgs= 1
P: Vendor=413c ProdID=8217 Rev= 5.04
S: Manufacturer=DELL
S: Product=COMPAL Electronics EXM-G1A
S: SerialNumber=359302940050401
C:* #Ifs= 6 Cfg#= 1 Atr=a0 MxPwr=500mA
I:* If#= 0 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=30 Driver=qcserial
E: Ad=01(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=81(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
I:* If#= 1 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=42 Prot=01 Driver=usbfs
E: Ad=02(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=82(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
I:* If#= 2 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=ff Prot=60 Driver=qcserial
E: Ad=84(I) Atr=03(Int.) MxPS= 10 Ivl=32ms
E: Ad=83(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=03(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
I:* If#= 3 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=ff Prot=40 Driver=qcserial
E: Ad=86(I) Atr=03(Int.) MxPS= 10 Ivl=32ms
E: Ad=85(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=04(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
I:* If#= 4 Alt= 0 #EPs= 1 Cls=ff(vend.) Sub=ff Prot=ff Driver=(none)
E: Ad=87(I) Atr=03(Int.) MxPS= 64 Ivl=32ms
I:* If#= 8 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=ff Prot=50 Driver=qmi_wwan
E: Ad=88(I) Atr=03(Int.) MxPS= 8 Ivl=32ms
E: Ad=8e(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=0f(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
It is 0x413c:0x8218
T: Bus=02 Lev=01 Prnt=01 Port=05 Cnt=01 Dev#= 3 Spd=480 MxCh= 0
D: Ver= 2.10 Cls=00(>ifc ) Sub=00 Prot=00 MxPS=64 #Cfgs= 1
P: Vendor=413c ProdID=8218 Rev= 0.00
S: Manufacturer=DELL
S: Product=COMPAL Electronics EXM-G1A
S: SerialNumber=359302940050401
C:* #Ifs= 1 Cfg#= 1 Atr=a0 MxPwr= 2mA
I:* If#= 0 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=ff Driver=qcserial
E: Ad=81(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=01(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
Signed-off-by: JackBB Wu <wojackbb@gmail.com>
Cc: stable@vger.kernel.org
Signed-off-by: Johan Hovold <johan@kernel.org>
|
|
The device IMST USB-Stick for Smart Meter is a rebranded IMST iM871A-USB
Wireless M-Bus USB-adapter. It is used to read wireless water, gas and
electricity meters.
Signed-off-by: Leonard Dallmayr <leonard.dallmayr@mailbox.org>
Cc: stable@vger.kernel.org
Signed-off-by: Johan Hovold <johan@kernel.org>
|
|
backend
Follow the PD PHY changes and rework Type-C port implementation to
become an encapsulated backend. While this is not required for the
PMI632, it will us later to enable Type-C handling on earlier platforms,
including, but not limited to SDM845, SDM660 and MSM8998.
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Tested-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Acked-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Link: https://lore.kernel.org/r/20240113-pmi632-typec-v2-8-182d9aa0a5b3@linaro.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Rework Qualcomm PMIC TCPM driver to allow different platform-specific
implementations of the PD PHY interface. While majority of platforms
has the same of register for the PD PHY, some obscure ones (PMI632) do
not have real PD PHY support. Add proper interface between the main
module and the PD PHY backend to allow switching the PD PHY
implementation.
Tested-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Acked-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Link: https://lore.kernel.org/r/20240113-pmi632-typec-v2-7-182d9aa0a5b3@linaro.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
The function qcom_pmic_typec_set_roles() passes enum values as boolean
values to qcom_pmic_typec_pdphy_set_roles(), which then interprets them
as bit values. Be more explicit about it, pass enum values directly and
compute corresponding bit masks in qcom_pmic_typec_pdphy_set_roles().
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Reviewed-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Link: https://lore.kernel.org/r/20240113-pmi632-typec-v2-6-182d9aa0a5b3@linaro.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
If the PD is disabled for the port, port->pds will be left as NULL,
which causes the following crash during caps intilisation. Fix the
crash.
Unable to handle kernel NULL pointer dereference at virtual address 0000000000000000
Call trace:
tcpm_register_port+0xaec/0xc44
qcom_pmic_typec_probe+0x1a4/0x254
platform_probe+0x68/0xc0
really_probe+0x148/0x2ac
__driver_probe_device+0x78/0x12c
driver_probe_device+0xd8/0x160
Bluetooth: hci0: QCA Product ID :0x0000000a
__device_attach_driver+0xb8/0x138
bus_for_each_drv+0x80/0xdc
Bluetooth: hci0: QCA SOC Version :0x40020150
__device_attach+0x9c/0x188
device_initial_probe+0x14/0x20
bus_probe_device+0xac/0xb0
deferred_probe_work_func+0x8c/0xc8
process_one_work+0x1ec/0x51c
worker_thread+0x1ec/0x3e4
kthread+0x120/0x124
ret_from_fork+0x10/0x20
Fixes: cd099cde4ed2 ("usb: typec: tcpm: Support multiple capabilities")
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Link: https://lore.kernel.org/r/20240113-pmi632-typec-v2-5-182d9aa0a5b3@linaro.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
The PPM on some Dell laptops seems to expect that the ACK_CC_CI
command to clear the connector change notification is in turn
followed by another ACK_CC_CI to acknowledge the ACK_CC_CI command
itself. This is in violation of the UCSI spec that states:
"The only notification that is not acknowledged by the OPM is
the command completion notification for the ACK_CC_CI or the
PPM_RESET command."
Add a quirk to send this ack anyway.
Apply the quirk to all Dell systems.
On the first command that acks a connector change send a dummy
command to determine if it runs into a timeout. Only activate
the quirk if it does. This ensure that we do not break Dell
systems that do not need the quirk.
Signed-off-by: "Christian A. Ehrhardt" <lk@c--e.de>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Link: https://lore.kernel.org/r/20240121204123.275441-4-lk@c--e.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
In case of a spurious or otherwise delayed notification it is
possible that CCI still reports the previous completion. The
UCSI spec is aware of this and provides two completion bits in
CCI, one for normal commands and one for acks. As acks and commands
alternate the notification handler can determine if the completion
bit is from the current command.
The initial UCSI code correctly handled this but the distinction
between the two completion bits was lost with the introduction of
the new API.
To fix this revive the ACK_PENDING bit for ucsi_acpi and only complete
commands if the completion bit matches.
Fixes: f56de278e8ec ("usb: typec: ucsi: acpi: Move to the new API")
Cc: stable@vger.kernel.org
Signed-off-by: "Christian A. Ehrhardt" <lk@c--e.de>
Acked-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Link: https://lore.kernel.org/r/20240121204123.275441-3-lk@c--e.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Calling ->sync_write must be done while holding the PPM lock as
the mailbox logic does not support concurrent commands.
At least since the addition of partner task this means that
ucsi_acknowledge_connector_change should be called with the
PPM lock held as it calls ->sync_write.
Thus protect the only call to ucsi_acknowledge_connector_change
with the PPM. All other calls to ->sync_write already happen
under the PPM lock.
Fixes: b9aa02ca39a4 ("usb: typec: ucsi: Add polling mechanism for partner tasks like alt mode checking")
Cc: stable@vger.kernel.org
Signed-off-by: "Christian A. Ehrhardt" <lk@c--e.de>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Link: https://lore.kernel.org/r/20240121204123.275441-2-lk@c--e.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
The ULPI per-device debugfs root is named after the ulpi device's
parent, but ulpi_unregister_interface tries to remove a debugfs
directory named after the ulpi device itself. This results in the
directory sticking around and preventing subsequent (deferred) probes
from succeeding. Change the directory name to match the ulpi device.
Fixes: bd0a0a024f2a ("usb: ulpi: Add debugfs support")
Cc: stable@vger.kernel.org
Signed-off-by: Sean Anderson <sean.anderson@seco.com>
Link: https://lore.kernel.org/r/20240126223800.2864613-1-sean.anderson@seco.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
This reverts commit 1e35f074399dece73d5df11847d4a0d7a6f49434.
Given that ERROR_RECOVERY calls into PORT_RESET for Hi-Zing
the CC pins, setting CC pins to default state during PORT_RESET
breaks error recovery.
4.5.2.2.2.1 ErrorRecovery State Requirements
The port shall not drive VBUS or VCONN, and shall present a
high-impedance to ground (above zOPEN) on its CC1 and CC2 pins.
Hi-Zing the CC pins is the inteded behavior for PORT_RESET.
CC pins are set to default state after tErrorRecovery in
PORT_RESET_WAIT_OFF.
4.5.2.2.2.2 Exiting From ErrorRecovery State
A Sink shall transition to Unattached.SNK after tErrorRecovery.
A Source shall transition to Unattached.SRC after tErrorRecovery.
Cc: stable@vger.kernel.org
Cc: Frank Wang <frank.wang@rock-chips.com>
Fixes: 1e35f074399d ("usb: typec: tcpm: fix cc role at port reset")
Signed-off-by: Badhri Jagan Sridharan <badhri@google.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Link: https://lore.kernel.org/r/20240117114742.2587779-1-badhri@google.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Delete one extraneous line of kernel-doc to prevent a kernel-doc
warning:
pch_udc.c:297: warning: Excess struct member 'desc' description in 'pch_udc_ep'
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: linux-usb@vger.kernel.org
Cc: tomoya-linux@dsn.lapis-semi.com
Link: https://lore.kernel.org/r/20240115003008.5763-1-rdunlap@infradead.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
When a USB gadget is configured through configfs with 1 or more f_fs
functions, then the logic setting up the gadget configuration has to wait
until the user space code (typically separate applications) responsible for
those functions have written their descriptors before the gadget can be
activated.
The f_fs instance already knows if this has been done, so expose it through
a "ready" attribute in configfs for easier synchronization.
Signed-off-by: Peter Korsgaard <peter@korsgaard.com>
Link: https://lore.kernel.org/r/20240126203208.2482573-1-peter@korsgaard.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
When DWC3 is set to host mode by programming register DWC3_GCTL, VBUS
(or its control signal) will be turned on immediately on related Root Hub
ports. Then, the VBUS is turned off for a little while(15us) when do xhci
reset (conducted by xhci driver) and back to normal finally, we can
observe a negative glitch of related signal happen.
This VBUS glitch might cause some USB devices enumeration fail if kernel
boot with them connected. Such as LS1012AFWRY/LS1043ARDB/LX2160AQDS
/LS1088ARDB with Kingston 16GB USB2.0/Kingston USB3.0/JetFlash Transcend
4GB USB2.0 drives. The fail cases include enumerated as full-speed device
or report wrong device descriptor, etc.
One SW workaround which can fix this is by programing all xhci PORTSC[PP]
to 0 to turn off VBUS immediately after setting host mode in DWC3 driver
(per signal measurement result, it will be too late to do it in
xhci-plat.c or xhci.c). Then, after xhci reset complete in xhci driver,
PORTSC[PP]s' value will back to 1 automatically and VBUS on at that time,
no glitch happen and normal enumeration process has no impact.
Acked-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com>
Signed-off-by: Ran Wang <ran.wang_1@nxp.com>
Reviewed-by: Peter Chen <peter.chen@nxp.com>
Signed-off-by: Frank Li <Frank.Li@nxp.com>
Link: https://lore.kernel.org/r/20240124152525.3910311-4-Frank.Li@nxp.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Split the PORT and CAPs macro definitions into a separate file to
facilitate sharing with other files without the need to include the entire
xhci.h.
Signed-off-by: Frank Li <Frank.Li@nxp.com>
Link: https://lore.kernel.org/r/20240124152525.3910311-2-Frank.Li@nxp.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
