| Age | Commit message (Collapse) | Author |
|---|
|
Add rx_lanes and tx_lanes lane count sysfs entries for a usb device
struct usb_devuce rx_lanes and tx_lanes variables.
Shows number of lanes used by the usb device
Data rate of a device is the lane speed * lane count, for example
USB 3.2 Gen 2x2 device uses 10Gbps signaling per lane, and has dual-lane
support 10Gbps * 2 = 20Gbps
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
USB 3.2 specification adds a Gen XxY notion for USB3 devices where
X is the signaling rate on the wire. Gen 1xY is 5Gbps Superspeed
and Gen 2xY is 10Gbps SuperSpeedPlus. Y is the lane count.
For normal, non inter-chip (SSIC) devies the rx and tx lane count is
symmetric, and the maximum lane count for USB 3.2 devices is 2 (dual-lane).
SSIC devices may have asymmetric lane counts, with up to four
lanes per direction. The USB 3.2 specification doesn't point out
how to use the Gen XxY notion for these devices, so we limit the Gen Xx2
notion to symmertic Dual lane devies.
For other devices just show Gen1 or Gen2
Gen 1 5Gbps
Gen 2 10Gbps
Gen 1x2 10Gbps Dual-lane (USB 3.2)
Gen 2x2 20Gbps Dual-lane (USB 3.2)
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Set the the rx_lane and tx_lane count to "2" for USB 3.2 hosts.
For all other older hosts set the default lane counts to 1
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
USB 3.2 specification adds Dual-lane support, doubling the maximum
SuperSpeedPlus data rate from 10Gbps to 20Gbps.
Dual-lane takes into use a second set of rx and tx wires/pins in the
Type-C cable and connector.
Add "rx_lanes" and "tx_lanes" variables to struct usb_device to store
the numer of lanes in use. Number of lanes can be read using the extended
port status hub request that was introduced in USB 3.1.
Extended port status rx and tx lane count are zero based, maximum
lanes supported by non inter-chip (SSIC) USB 3.2 is 2 (dual lane) with
rx and tx lane count symmetric. SSIC devices support asymmetric lanes
up to 4 lanes per direction.
If extended port status is not available then default to one lane.
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Hosts that support USB 3.2 Enhaned SuperSpeed can set their hcd speed
to HCD_USB32 to let usb core and host drivers know that the controller
supports new USB 3.2 dual-lane features.
make sure usb core handle HCD_USB32 hosts correctly, for now similar
to HCD_USB32.
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
On Armada 7K/8K we need to explicitly enable the register clock. This
clock is optional because not all the SoCs using this IP need it but at
least for Armada 7K/8K it is actually mandatory.
The change was done at xhci-plat level and not at a xhci-mvebu.c because,
it is expected that other SoC would have this kind of constraint.
The binding documentation is updating accordingly.
Signed-off-by: Gregory CLEMENT <gregory.clement@bootlin.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
clk_disable_unprepare() already checks that the clock pointer is valid.
No need to test it before calling it.
Signed-off-by: Gregory CLEMENT <gregory.clement@bootlin.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Since there is no user of max_snk_*, so we can remove them from tcpm.
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Li Jun <jun.li@nxp.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Acked-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Since max_snk_* is to be deprecated, so remove max_snk_* by adding a
variable PDO for sink config.
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Li Jun <jun.li@nxp.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Acked-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Since max_snk_* is to be deprecated, so remove max_snk_* by adding a
variable PDO for sink config.
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Li Jun <jun.li@nxp.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Acked-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
This patch is a combination of commit 57e6f0d7b804
("typec: tcpm: Only request matching pdos") and source
pdo selection optimization based on it, instead of only
compare between the same pdo type of sink and source,
we should check source pdo voltage range is within the
voltage range of one sink pdo.
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Li Jun <jun.li@nxp.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Acked-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
wait_for_connected() wait till a port change status to
USB_PORT_STAT_CONNECTION, but this is not possible if
the port is unpowered. The loop will only exit at timeout.
Such case take place if an over-current incident happen
while system is in S3. Then during resume wait_for_connected()
will wait 2s, which may be noticeable by the user.
Signed-off-by: Dominik Bozek <dominikx.bozek@intel.com>
Signed-off-by: Kuppuswamy Sathyanarayanan <sathyanarayanan.kuppuswamy@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
We should get drvdata from struct device directly. Going via
platform_device is an unneeded step back and forth.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Acked-by: Chunfeng Yun <chunfeng.yun@mediatek.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
We should get drvdata from struct device directly. Going via
platform_device is an unneeded step back and forth.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
The legacy interface for associating controllers with phys from board
files and platform code has been unused since commit 9080b8dc761a ("ARM:
OMAP2+: Remove legacy usb-host.c platform init code"). Since then, all
calls to usb_get_phy_dev() and its devres version have been returning
-ENODEV.
Now that the final calls to these functions have been removed, we can
drop this legacy lookup interface altogether.
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Drop support for legacy phys for rcar2 which hasn't been used with a
mainline kernel since commit 9080b8dc761a ("ARM: OMAP2+: Remove legacy
usb-host.c platform init code"). Specifically, since that commit
usb_get_phy_dev() have always returned -ENODEV and consequently this
code has not been used.
Note that the legacy-phy API is still being used in gadget mode to bind
the peripheral controller.
Acked-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Drop support for non-DT systems, which hasn't been used by a mainline
kernel since commit 9080b8dc761a ("ARM: OMAP2+: Remove legacy usb-host.c
platform init code"). Specifically, since that commit usb_get_phy_dev()
have always returned -ENODEV when looking up a legacy phy, something
which in turn would have led to the init callback returning
-EPROBE_DEFER indefinitely.
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Drop support for looking up legacy phys defined by board files,
something which hasn't been used by a mainline kernel since commit
9080b8dc761a ("ARM: OMAP2+: Remove legacy usb-host.c platform init
code"). Specifically, since that commit usb_get_phy_dev() have always
returned -ENODEV and consequently this code has not been used.
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Drop support for looking up and initialising legacy phys in USB core,
something which hasn't been used by a mainline kernel since commit
9080b8dc761a ("ARM: OMAP2+: Remove legacy usb-host.c platform init
code"). Specifically, since that commit usb_get_phy_dev() have always
returned -ENODEV and consequently this code has not been used.
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Drop the unused legacy usb_bind_phy() helper whose last user was removed
in 2016 when OMAP moved to device-tree boot (9080b8dc761a ("ARM: OMAP2+:
Remove legacy usb-host.c platform init code")).
Note that this means that for the last couple of years the phy_bind_list
has been empty (when using mainline kernels) and that consequently all
phy lookups using the usb_get_phy_dev() interface have failed with
-ENODEV. This helper along with its current users will be removed by
follow-on patches.
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Refine probe and disconnect debug msgs to be useful and say what is
in progress.
Signed-off-by: Shuah Khan <shuahkh@osg.samsung.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Remove dependencies on HAS_DMA where a Kconfig symbol depends on another
symbol that implies HAS_DMA, and, optionally, on "|| COMPILE_TEST".
In most cases this other symbol is an architecture or platform specific
symbol, or PCI.
Generic symbols and drivers without platform dependencies keep their
dependencies on HAS_DMA, to prevent compiling subsystems or drivers that
cannot work anyway.
This simplifies the dependencies, and allows to improve compile-testing.
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Reviewed-by: Mark Brown <broonie@kernel.org>
Acked-by: Robin Murphy <robin.murphy@arm.com>
Acked-by: Felipe Balbi <felipe.balbi@linux.intel.com> [drivers/usb/gadget/]
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
isp1760_stop() is never called in atomic context.
The call chain ending up at isp1760_stop() is:
[1] isp1760_stop() <- isp1760_shutdown()
isp1760_shutdown() is set as ".shutdown" in struct hc_driver.
isp1760_stop() is also set as ".stop" in hc_driver.
These functions are not called in atomic context.
Despite never getting called from atomic context, isp1760_stop()
calls mdelay() to busily wait.
This is not necessary and can be replaced with msleep() to
avoid busy waiting.
This is found by a static analysis tool named DCNS written by myself.
And I also manually check it
Signed-off-by: Jia-Ju Bai <baijiaju1990@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
isp1760_init_core() is never called in atomic context.
The call chains ending up at isp1760_init_core() are:
[1] isp1760_init_core() <- isp1760_register() <- isp1760_plat_probe()
[2] isp1760_init_core() <- isp1760_register() <- isp1761_pci_probe()
isp1760_plat_probe() is set as ".probe" in struct platform_driver.
isp1761_pci_probe() is set as ".probe" in struct pci_driver.
These functions are not called in atomic context.
Despite never getting called from atomic context, isp1761_pci_probe()
calls mdelay() to busily wait.
This is not necessary and can be replaced with msleep() to
avoid busy waiting.
This is found by a static analysis tool named DCNS written by myself.
And I also manually check it.
Signed-off-by: Jia-Ju Bai <baijiaju1990@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
init_freecom() is never called in atomic context.
init_freecom() is set as ".initFunction" through UNUSUAL_DEV().
And ->initFunction() is only called by usb_stor_acquire_resources(),
which is only called by usb_stor_probe2().
usb_stor_probe2() is called by *_probe() functions (like alauda_probe())
for each USB driver.
*_probe() functions are set ".probe" in struct usb_driver.
These functions are not called in atomic context.
Despite never getting called from atomic context, init_freecom()
calls mdelay() to busily wait.
This is not necessary and can be replaced with msleep() to
avoid busy waiting.
This is found by a static analysis tool named DCNS written by myself.
And I also manually check it.
Signed-off-by: Jia-Ju Bai <baijiaju1990@gmail.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
platform_get_resource() may fail and return NULL, so we should
better check it's return value to avoid a NULL pointer dereference
a bit later in the code.
This is detected by Coccinelle semantic patch.
@@
expression pdev, res, n, t, e, e1, e2;
@@
res = platform_get_resource(pdev, t, n);
+ if (!res)
+ return -EINVAL;
... when != res == NULL
e = devm_ioremap_nocache(e1, res->start, e2);
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Use new return type vm_fault_t for the fault handler
in struct vm_operations_struct. For now, this is just
documenting that the function returns a VM_FAULT value
rather than an errno. Once all instances are converted,
vm_fault_t will become a distinct type.
Reference id -> 1c8f422059ae ("mm: change return type to
vm_fault_t")
Signed-off-by: Souptick Joarder <jrdr.linux@gmail.com>
Reviewed-by: Matthew Wilcox <mawilcox@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
tty_unregister_driver may be called more than 1 time in some
hotplug cases,it will cause the kernel oops. This patch checked
dbc_tty_driver to make sure it is unregistered only 1 time.
[ 175.741404] BUG: unable to handle kernel NULL pointer dereference at 0000000000000034
[ 175.742309] IP: tty_unregister_driver+0x9/0x70
[ 175.743148] PGD 0 P4D 0
[ 175.743981] Oops: 0000 [#1] SMP PTI
[ 175.753904] RIP: 0010:tty_unregister_driver+0x9/0x70
[ 175.754817] RSP: 0018:ffffa8ff831d3bb0 EFLAGS: 00010246
[ 175.755753] RAX: 0000000000000000 RBX: 0000000000000000 RCX: 0000000000000000
[ 175.756685] RDX: ffff92089c616000 RSI: ffffe64fe1b26080 RDI: 0000000000000000
[ 175.757608] RBP: ffff92086c988230 R08: 000000006c982701 R09: 00000001801e0016
[ 175.758533] R10: ffffa8ff831d3b48 R11: ffff92086c982100 R12: ffff92086c98827c
[ 175.759462] R13: ffff92086c988398 R14: 0000000000000060 R15: ffff92089c5e9b40
[ 175.760401] FS: 0000000000000000(0000) GS:ffff9208a0100000(0000) knlGS:0000000000000000
[ 175.761334] CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033
[ 175.762270] CR2: 0000000000000034 CR3: 000000011800a003 CR4: 00000000003606e0
[ 175.763225] DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000
[ 175.764164] DR3: 0000000000000000 DR6: 00000000fffe0ff0 DR7: 0000000000000400
[ 175.765091] Call Trace:
[ 175.766014] xhci_dbc_tty_unregister_driver+0x11/0x30
[ 175.766960] xhci_dbc_exit+0x2a/0x40
[ 175.767889] xhci_stop+0x57/0x1c0
[ 175.768824] usb_remove_hcd+0x100/0x250
[ 175.769708] usb_hcd_pci_remove+0x68/0x130
[ 175.770574] pci_device_remove+0x3b/0xc0
[ 175.771435] device_release_driver_internal+0x157/0x230
[ 175.772343] pci_stop_bus_device+0x74/0xa0
[ 175.773205] pci_stop_bus_device+0x2b/0xa0
[ 175.774061] pci_stop_bus_device+0x2b/0xa0
[ 175.774907] pci_stop_bus_device+0x2b/0xa0
[ 175.775741] pci_stop_bus_device+0x2b/0xa0
[ 175.776618] pci_stop_bus_device+0x2b/0xa0
[ 175.777452] pci_stop_bus_device+0x2b/0xa0
[ 175.778273] pci_stop_bus_device+0x2b/0xa0
[ 175.779092] pci_stop_bus_device+0x2b/0xa0
[ 175.779908] pci_stop_bus_device+0x2b/0xa0
[ 175.780750] pci_stop_bus_device+0x2b/0xa0
[ 175.781543] pci_stop_and_remove_bus_device+0xe/0x20
[ 175.782338] pciehp_unconfigure_device+0xb8/0x160
[ 175.783128] pciehp_disable_slot+0x4f/0xd0
[ 175.783920] pciehp_power_thread+0x82/0xa0
[ 175.784766] process_one_work+0x147/0x3c0
[ 175.785564] worker_thread+0x4a/0x440
[ 175.786376] kthread+0xf8/0x130
[ 175.787174] ? rescuer_thread+0x360/0x360
[ 175.787964] ? kthread_associate_blkcg+0x90/0x90
[ 175.788798] ret_from_fork+0x35/0x40
Cc: <stable@vger.kernel.org> # 4.16
Fixes: dfba2174dc42 ("usb: xhci: Add DbC support in xHCI driver")
Signed-off-by: Zhengjun Xing <zhengjun.xing@linux.intel.com>
Tested-by: Christian Kellner <christian@kellner.me>
Reviewed-by: Christian Kellner <christian@kellner.me>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
The new axp288 extcon driver has no dependency on USB itself but
calls the usb role switch helper functions. This causes a link error
when USB_COMMON is disabled, as that subdirectory never gets entered:
drivers/extcon/extcon-axp288.o: In function `axp288_usb_role_work':
extcon-axp288.c:(.text+0x47b): undefined reference to `usb_role_switch_set_role'
extcon-axp288.c:(.text+0x498): undefined reference to `usb_role_switch_get_role'
drivers/extcon/extcon-axp288.o: In function `axp288_extcon_probe':
extcon-axp288.c:(.text+0x675): undefined reference to `usb_role_switch_get'
extcon-axp288.c:(.text+0x6d1): undefined reference to `usb_role_switch_put'
drivers/extcon/extcon-axp288.o: In function `axp288_put_role_sw':
extcon-axp288.c:(.text+0x1c): undefined reference to `usb_role_switch_put'
There are multiple ways of fixing this, I chose to 'select USB_COMMON',
since that is how we solved the same problem for other helpers like
USB_LED_TRIG or PHY drivers.
Fixes: d54f063cdbe4 ("extcon: axp288: Set USB role where necessary")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Currently hcd.c is the only consumer of the usb_phy_roothub logic. This
already includes the required header files so struct device is known.
However, future consumers might not know about struct device.
Add a forward declaration for struct device to fix potential future
consumers which don't include any of the struct device API headers.
Fixes: 07dbff0ddbd86c ("usb: core: add a wrapper for the USB PHYs on the HCD")
Suggested-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
If the generic PHY support is disabled the stub of devm_of_phy_get_by_index
returns ENOSYS. This corner case isn't handled properly by
usb_phy_roothub_add_phy and at least breaks USB support on Raspberry Pi
(bcm2835_defconfig):
dwc2 20980000.usb: dwc2_hcd_init() FAILED, returning -38
dwc2: probe of 20980000.usb failed with error -38
Let usb_phy_roothub_alloc() return in case CONFIG_GENERIC_PHY is
disabled to fix this issue (compilers might even be smart enough to
optimize away most of the code within usb_phy_roothub_alloc and
usb_phy_roothub_add_phy if CONFIG_GENERIC_PHY is disabled). All
existing usb_phy_roothub_* functions are already NULL-safe, so no
special handling is required there.
Fixes: 07dbff0ddbd8 ("usb: core: add a wrapper for the USB PHYs on the HCD")
Reported-by: Stefan Wahren <stefan.wahren@i2se.com>
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
If the USB controller can wake up the system (which is the case for
example with the Mediatek USB3 IP) then we must not call phy_exit during
suspend to ensure that the USB controller doesn't have to re-enumerate
the devices during resume.
However, if the USB controller cannot wake up the system (which is the
case for example on various TI platforms using a dwc3 controller) then
we must call phy_exit during suspend. Otherwise the PHY driver keeps the
clocks enabled, which prevents the system from reaching the lowest power
levels in the suspend state.
Solve this by introducing two new functions in the PHY wrapper which are
dedicated to the suspend and resume handling.
If the controller can wake up the system the new usb_phy_roothub_suspend
function will simply call usb_phy_roothub_power_off. However, if wake up
is not supported by the controller it will also call
usb_phy_roothub_exit.
The also new usb_phy_roothub_resume function takes care of calling
usb_phy_roothub_init (if the controller can't wake up the system) in
addition to usb_phy_roothub_power_on.
Fixes: 07dbff0ddbd86c ("usb: core: add a wrapper for the USB PHYs on the HCD")
Fixes: 178a0bce05cbc1 ("usb: core: hcd: integrate the PHY wrapper into the HCD core")
Reported-by: Roger Quadros <rogerq@ti.com>
Suggested-by: Roger Quadros <rogerq@ti.com>
Suggested-by: Chunfeng Yun <chunfeng.yun@mediatek.com>
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Tested-by: Chunfeng Yun <chunfeng.yun@mediatek.com>
Reviewed-by: Roger Quadros <rogerq@ti.com>
Tested-by: Keerthy <j-keerthy@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Before this patch usb_phy_roothub_init served two purposes (from a
caller's point of view - like hcd.c):
- parsing the PHYs and allocating the list entries
- calling phy_init on each list entry
While this worked so far it has one disadvantage: if we need to call
phy_init for each PHY instance then the existing code cannot be re-used.
Solve this by splitting off usb_phy_roothub_alloc which only parses the
PHYs and allocates the list entries.
usb_phy_roothub_init then gets a struct usb_phy_roothub and only calls
phy_init on each PHY instance (along with the corresponding cleanup if
that failed somewhere).
This is a preparation step for adding proper suspend support for some
hardware that requires phy_exit to be called during suspend and phy_init
to be called during resume.
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Tested-by: Chunfeng Yun <chunfeng.yun@mediatek.com>
Reviewed-by: Roger Quadros <rogerq@ti.com>
Tested-by: Keerthy <j-keerthy@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
usb_phy_roothub_exit() should return the error code from the phy_exit()
call if exiting the PHY failed.
However, since a wrong variable is used usb_phy_roothub_exit() currently
always returns 0, even if one of the phy_exit calls returned an error.
Clang also reports this bug:
kernel/drivers/usb/core/phy.c:114:8: warning: explicitly assigning value of
variable of type 'int' to itself [-Wself-assign] error, forbidden
warning: phy.c:114
Fix this by assigning the error code from phy_exit() to the "ret"
variable to propagate the error correctly.
Fixes: 07dbff0ddbd86c ("usb: core: add a wrapper for the USB PHYs on the HCD")
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Rishabh Bhatnagar <rishabhb@codeaurora.org>
Tested-by: Keerthy <j-keerthy@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
On some boards, under heavy load, the EC firmware is
unable to complete commands even in one second. Increasing
the command completion timeout value to five seconds.
Reported-by: Quanxian Wang <quanxian.wang@intel.com>
Fixes: c1b0bc2dabfa ("usb: typec: Add support for UCSI interface")
Cc: <stable@vger.kernel.org>
Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
This reverts commit b07c12517f2aed0add8ce18146bb426b14099392
It is incomplete and causes hangs on devices when shutting down. It
needs a much more "complete" fix in order to work properly. As that fix
has not been merged, revert this patch for now before it causes any more
problems.
Cc: Greg Hackmann <ghackmann@google.com>
Cc: Adam Wallis <awallis@codeaurora.org>
Cc: Mathias Nyman <mathias.nyman@intel.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Add DELAY_INIT quirk to fix the following problem with HP
v222w 16GB Mini:
usb 1-3: unable to read config index 0 descriptor/start: -110
usb 1-3: can't read configurations, error -110
usb 1-3: can't set config #1, error -110
Signed-off-by: Kamil Lulko <kamilx.lulko@intel.com>
Signed-off-by: Kuppuswamy Sathyanarayanan <sathyanarayanan.kuppuswamy@linux.intel.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
There is the following build error with CONFIG_TYPEC_UCSI=m, CONFIG_FTRACE=y
and CONFIG_TRACING=n:
ERROR: "__tracepoint_ucsi_command" [drivers/usb/typec/ucsi/typec_ucsi.ko] undefined!
ERROR: "__tracepoint_ucsi_register_port" [drivers/usb/typec/ucsi/typec_ucsi.ko] undefined!
ERROR: "__tracepoint_ucsi_notify" [drivers/usb/typec/ucsi/typec_ucsi.ko] undefined!
ERROR: "__tracepoint_ucsi_reset_ppm" [drivers/usb/typec/ucsi/typec_ucsi.ko] undefined!
ERROR: "__tracepoint_ucsi_run_command" [drivers/usb/typec/ucsi/typec_ucsi.ko] undefined!
ERROR: "__tracepoint_ucsi_ack" [drivers/usb/typec/ucsi/typec_ucsi.ko] undefined!
ERROR: "__tracepoint_ucsi_connector_change" [drivers/usb/typec/ucsi/typec_ucsi.ko] undefined!
This compination is quite hard to create because CONFIG_TRACING gets selected
only in rare cases without CONFIG_FTRACE.
The build failure is caused by conditionally compiling trace.c depending on
the wrong option CONFIG_FTRACE. Change this to depend on CONFIG_TRACING like
other users of tracepoints do.
Fixes: c1b0bc2dabfa ("usb: typec: Add support for UCSI interface")
Signed-off-by: Tobias Regnery <tobias.regnery@gmail.com>
Acked-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Fix it to not print kernel pointer address. Remove the conditional
and debug message as it isn't very useful.
Signed-off-by: Shuah Khan <shuahkh@osg.samsung.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
usbip_host calls device_attach() without holding dev->parent lock.
Fix it.
Signed-off-by: Shuah Khan <shuahkh@osg.samsung.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
vhci_hcd fails to do reset to put usb device and sockfd in the
module remove/stop paths. Fix the leak.
Signed-off-by: Shuah Khan <shuahkh@osg.samsung.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Validate !rhport < 0 before using it to access port_status array.
Signed-off-by: Shuah Khan <shuahkh@osg.samsung.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
On chromebooks we depend on wakeup count to identify the wakeup source.
But currently USB devices do not increment the wakeup count when they
trigger the remote wake. This patch addresses the same.
Resume condition is reported differently on USB 2.0 and USB 3.0 devices.
On USB 2.0 devices, a wake capable device, if wake enabled, drives
resume signal to indicate a remote wake (USB 2.0 spec section 7.1.7.7).
The upstream facing port then sets C_PORT_SUSPEND bit and reports a
port change event (USB 2.0 spec section 11.24.2.7.2.3). Thus if a port
has resumed before driving the resume signal from the host and
C_PORT_SUSPEND is set, then the device attached to the given port might
be the reason for the last system wakeup. Increment the wakeup count for
the same.
On USB 3.0 devices, a function may signal that it wants to exit from device
suspend by sending a Function Wake Device Notification to the host (USB3.0
spec section 8.5.6.4) Thus on receiving the Function Wake, increment the
wakeup count.
Signed-off-by: Ravi Chandra Sadineni <ravisadineni@chromium.org>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
On Armada 7K/8K we need to explicitly enable the register clock. This
clock is optional because not all the SoCs using this IP need it but at
least for Armada 7K/8K it is actually mandatory.
The change was done at xhci-plat level and not at a xhci-mvebu.c because,
it is expected that other SoC would have this kind of constraint.
The binding documentation is updating accordingly.
Signed-off-by: Gregory CLEMENT <gregory.clement@bootlin.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
clk_disable_unprepare() already checks that the clock pointer is valid.
No need to test it before calling it.
Signed-off-by: Gregory CLEMENT <gregory.clement@bootlin.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
The Dell Inspiron 5775 is a Raven Ridge. The Enable Slot command timed
out when a USB device gets plugged:
[ 212.156326] xhci_hcd 0000:03:00.3: Error while assigning device slot ID
[ 212.156340] xhci_hcd 0000:03:00.3: Max number of devices this xHCI host supports is 64.
[ 212.156348] usb usb2-port3: couldn't allocate usb_device
AMD suggests that a delay before xHC suspends can fix the issue.
I can confirm it fixes the issue, so use the suspend delay quirk for
Raven Ridge's xHC.
Cc: stable@vger.kernel.org
Signed-off-by: Kai-Heng Feng <kai.heng.feng@canonical.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Arrow USB Blaster integrated on MAX1000 board uses the same vendor ID
(0x0403) and product ID (0x6010) as the "original" FTDI device.
This patch avoids picking up by ftdi_sio of the first interface of this
USB device. After that this device can be used by Arrow user-space JTAG
driver.
Signed-off-by: Vasyl Vavrychuk <vvavrychuk@gmail.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
|
|
Added the USB VID and PID for the USB serial console on some National
Instruments devices.
Signed-off-by: Kyle Roeschley <kyle.roeschley@ni.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
|
|
Add simple driver for libtransistor USB console.
This device is implemented in software:
https://github.com/reswitched/libtransistor/blob/development/lib/usb_serial.c
Signed-off-by: Collin May <collin@collinswebsite.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/jmorris/linux-security
Pull general security layer updates from James Morris:
- Convert security hooks from list to hlist, a nice cleanup, saving
about 50% of space, from Sargun Dhillon.
- Only pass the cred, not the secid, to kill_pid_info_as_cred and
security_task_kill (as the secid can be determined from the cred),
from Stephen Smalley.
- Close a potential race in kernel_read_file(), by making the file
unwritable before calling the LSM check (vs after), from Kees Cook.
* 'next-general' of git://git.kernel.org/pub/scm/linux/kernel/git/jmorris/linux-security:
security: convert security hooks to use hlist
exec: Set file unwritable before LSM check
usb, signal, security: only pass the cred, not the secid, to kill_pid_info_as_cred and security_task_kill
|
