| Age | Commit message (Collapse) | Author |
|---|
|
Resources should be released only after all threads that utilize them
have been destroyed.
This commit ensures that resources are not released prematurely by waiting
for the associated workqueue to complete before deallocating them.
Cc: stable <stable@kernel.org>
Fixes: b9aa02ca39a4 ("usb: typec: ucsi: Add polling mechanism for partner tasks like alt mode checking")
Signed-off-by: Andrei Kuchynski <akuchynski@chromium.org>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Link: https://lore.kernel.org/r/20250305111739.1489003-2-akuchynski@chromium.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
When used on Huawei hisi platforms, Prolific Mass Storage Card Reader
which the VID:PID is in 067b:2731 might fail to enumerate at boot time
and doesn't work well with LPM enabled, combination quirks:
USB_QUIRK_DELAY_INIT + USB_QUIRK_NO_LPM
fixed the problems.
Signed-off-by: Miao Li <limiao@kylinos.cn>
Cc: stable <stable@kernel.org>
Link: https://lore.kernel.org/r/20250304070757.139473-1-limiao870622@163.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
A recent cleanup went a bit too far and dropped clearing the cycle bit
of link TRBs, so it stays different from the rest of the ring half of
the time. Then a race occurs: if the xHC reaches such link TRB before
more commands are queued, the link's cycle bit unintentionally matches
the xHC's cycle so it follows the link and waits for further commands.
If more commands are queued before the xHC gets there, inc_enq() flips
the bit so the xHC later sees a mismatch and stops executing commands.
This function is called before suspend and 50% of times after resuming
the xHC is doomed to get stuck sooner or later. Then some Stop Endpoint
command fails to complete in 5 seconds and this shows up
xhci_hcd 0000:00:10.0: xHCI host not responding to stop endpoint command
xhci_hcd 0000:00:10.0: xHCI host controller not responding, assume dead
xhci_hcd 0000:00:10.0: HC died; cleaning up
followed by loss of all USB decives on the affected bus. That's if you
are lucky, because if Set Deq gets stuck instead, the failure is silent.
Likely responsible for kernel bug 219824. I found this while searching
for possible causes of that regression and reproduced it locally before
hearing back from the reporter. To repro, simply wait for link cycle to
become set (debugfs), then suspend, resume and wait. To accelerate the
failure I used a script which repeatedly starts and stops a UVC camera.
Some HCs get fully reinitialized on resume and they are not affected.
Link: https://bugzilla.kernel.org/show_bug.cgi?id=219824
Fixes: 36b972d4b7ce ("usb: xhci: improve xhci_clear_command_ring()")
Cc: stable@vger.kernel.org
Signed-off-by: Michal Pecio <michal.pecio@gmail.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20250304113147.3322584-2-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
After phy initialization, some phy operations can only be executed while
in lower P states. Ensure GUSB3PIPECTL.SUSPENDENABLE and
GUSB2PHYCFG.SUSPHY are set soon after initialization to avoid blocking
phy ops.
Previously the SUSPENDENABLE bits are only set after the controller
initialization, which may not happen right away if there's no gadget
driver or xhci driver bound. Revise this to clear SUSPENDENABLE bits
only when there's mode switching (change in GCTL.PRTCAPDIR).
Fixes: 6d735722063a ("usb: dwc3: core: Prevent phy suspend during init")
Cc: stable <stable@kernel.org>
Signed-off-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com>
Link: https://lore.kernel.org/r/633aef0afee7d56d2316f7cc3e1b2a6d518a8cc9.1738280911.git.Thinh.Nguyen@synopsys.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
The xHC resources allocated for USB devices are not released in correct
order after resuming in case when while suspend device was reconnected.
This issue has been detected during the fallowing scenario:
- connect hub HS to root port
- connect LS/FS device to hub port
- wait for enumeration to finish
- force host to suspend
- reconnect hub attached to root port
- wake host
For this scenario during enumeration of USB LS/FS device the Cadence xHC
reports completion error code for xHC commands because the xHC resources
used for devices has not been properly released.
XHCI specification doesn't mention that device can be reset in any order
so, we should not treat this issue as Cadence xHC controller bug.
Similar as during disconnecting in this case the device resources should
be cleared starting form the last usb device in tree toward the root hub.
To fix this issue usbcore driver should call hcd->driver->reset_device
for all USB devices connected to hub which was reconnected while
suspending.
Fixes: 3d82904559f4 ("usb: cdnsp: cdns3 Add main part of Cadence USBSSP DRD Driver")
Cc: stable <stable@kernel.org>
Signed-off-by: Pawel Laszczak <pawell@cadence.com>
Reviewed-by: Alan Stern <stern@rowland.harvard.edu>
Link: https://lore.kernel.org/r/PH7PR07MB953841E38C088678ACDCF6EEDDCC2@PH7PR07MB9538.namprd07.prod.outlook.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
When performing continuous unbind/bind operations on the USB drivers
available on the Renesas RZ/G2L SoC, a kernel crash with the message
"Unable to handle kernel NULL pointer dereference at virtual address"
may occur. This issue points to the usbhsc_notify_hotplug() function.
Flush the delayed work to avoid its execution when driver resources are
unavailable.
Fixes: bc57381e6347 ("usb: renesas_usbhs: use delayed_work instead of work_struct")
Cc: stable <stable@kernel.org>
Reviewed-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Tested-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Claudiu Beznea <claudiu.beznea.uj@bp.renesas.com>
Link: https://lore.kernel.org/r/20250225110248.870417-4-claudiu.beznea.uj@bp.renesas.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
The gpriv->transceiver is retrieved in probe() through usb_get_phy() but
never released. Use devm_usb_get_phy() to handle this scenario.
This issue was identified through code investigation. No issue was found
without this change.
Fixes: b5a2875605ca ("usb: renesas_usbhs: Allow an OTG PHY driver to provide VBUS")
Cc: stable <stable@kernel.org>
Reviewed-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Tested-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Claudiu Beznea <claudiu.beznea.uj@bp.renesas.com>
Link: https://lore.kernel.org/r/20250225110248.870417-3-claudiu.beznea.uj@bp.renesas.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Clocks acquired with of_clk_get() need to be freed with clk_put(). Call
clk_put() on priv->clks[0] on error path.
Fixes: 3df0e240caba ("usb: renesas_usbhs: Add multiple clocks management")
Cc: stable <stable@kernel.org>
Reviewed-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Tested-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Claudiu Beznea <claudiu.beznea.uj@bp.renesas.com>
Link: https://lore.kernel.org/r/20250225110248.870417-2-claudiu.beznea.uj@bp.renesas.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
While commit d325a1de49d6 ("usb: dwc3: gadget: Prevent losing events in
event cache") makes sure that top half(TH) does not end up overwriting the
cached events before processing them when the TH gets invoked more than one
time, returning IRQ_HANDLED results in occasional irq storm where the TH
hogs the CPU. The irq storm can be prevented by the flag before event
handler busy is cleared. Default enable interrupt moderation in all
versions which support them.
ftrace event stub during dwc3 irq storm:
irq/504_dwc3-1111 ( 1111) [000] .... 70.000866: irq_handler_exit: irq=14 ret=handled
irq/504_dwc3-1111 ( 1111) [000] .... 70.000872: irq_handler_entry: irq=504 name=dwc3
irq/504_dwc3-1111 ( 1111) [000] .... 70.000874: irq_handler_exit: irq=504 ret=handled
irq/504_dwc3-1111 ( 1111) [000] .... 70.000881: irq_handler_entry: irq=504 name=dwc3
irq/504_dwc3-1111 ( 1111) [000] .... 70.000883: irq_handler_exit: irq=504 ret=handled
irq/504_dwc3-1111 ( 1111) [000] .... 70.000889: irq_handler_entry: irq=504 name=dwc3
irq/504_dwc3-1111 ( 1111) [000] .... 70.000892: irq_handler_exit: irq=504 ret=handled
irq/504_dwc3-1111 ( 1111) [000] .... 70.000898: irq_handler_entry: irq=504 name=dwc3
irq/504_dwc3-1111 ( 1111) [000] .... 70.000901: irq_handler_exit: irq=504 ret=handled
irq/504_dwc3-1111 ( 1111) [000] .... 70.000907: irq_handler_entry: irq=504 name=dwc3
irq/504_dwc3-1111 ( 1111) [000] .... 70.000909: irq_handler_exit: irq=504 ret=handled
irq/504_dwc3-1111 ( 1111) [000] .... 70.000915: irq_handler_entry: irq=504 name=dwc3
irq/504_dwc3-1111 ( 1111) [000] .... 70.000918: irq_handler_exit: irq=504 ret=handled
irq/504_dwc3-1111 ( 1111) [000] .... 70.000924: irq_handler_entry: irq=504 name=dwc3
irq/504_dwc3-1111 ( 1111) [000] .... 70.000927: irq_handler_exit: irq=504 ret=handled
irq/504_dwc3-1111 ( 1111) [000] .... 70.000933: irq_handler_entry: irq=504 name=dwc3
irq/504_dwc3-1111 ( 1111) [000] .... 70.000935: irq_handler_exit: irq=504 ret=handled
....
Cc: stable <stable@kernel.org>
Suggested-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com>
Fixes: d325a1de49d6 ("usb: dwc3: gadget: Prevent losing events in event cache")
Signed-off-by: Badhri Jagan Sridharan <badhri@google.com>
Acked-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com>
Link: https://lore.kernel.org/r/20250216223003.3568039-1-badhri@google.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
If the USB configuration is not valid, then avoid checking for
bmAttributes to prevent null pointer deference.
Cc: stable <stable@kernel.org>
Fixes: 40e89ff5750f ("usb: gadget: Set self-powered based on MaxPower and bmAttributes")
Signed-off-by: Prashanth K <prashanth.k@oss.qualcomm.com>
Link: https://lore.kernel.org/r/20250224085604.417327-1-prashanth.k@oss.qualcomm.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
When adding support for USB3-over-USB4 tunnelling detection, a check
for an Intel-specific capability was added. This capability, which
goes by ID 206, is used without any check that we are actually
dealing with an Intel host.
As it turns out, the Cadence XHCI controller *also* exposes an
extended capability numbered 206 (for unknown purposes), but of
course doesn't have the Intel-specific registers that the tunnelling
code is trying to access. Fun follows.
The core of the problems is that the tunnelling code blindly uses
vendor-specific capabilities without any check (the Intel-provided
documentation I have at hand indicates that 192-255 are indeed
vendor-specific).
Restrict the detection code to Intel HW for real, preventing any
further explosion on my (non-Intel) HW.
Cc: stable <stable@kernel.org>
Fixes: 948ce83fbb7df ("xhci: Add USB4 tunnel detection for USB3 devices on Intel hosts")
Signed-off-by: Marc Zyngier <maz@kernel.org>
Acked-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20250227194529.2288718-1-maz@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Raspberry Pi is a major user of those chips and they discovered a bug -
when the end of a transfer ring segment is reached, up to four TRBs can
be prefetched from the next page even if the segment ends with link TRB
and on page boundary (the chip claims to support standard 4KB pages).
It also appears that if the prefetched TRBs belong to a different ring
whose doorbell is later rung, they may be used without refreshing from
system RAM and the endpoint will stay idle if their cycle bit is stale.
Other users complain about IOMMU faults on x86 systems, unsurprisingly.
Deal with it by using existing quirk which allocates a dummy page after
each transfer ring segment. This was seen to resolve both problems. RPi
came up with a more efficient solution, shortening each segment by four
TRBs, but it complicated the driver and they ditched it for this quirk.
Also rename the quirk and add VL805 device ID macro.
Signed-off-by: Michal Pecio <michal.pecio@gmail.com>
Link: https://github.com/raspberrypi/linux/issues/4685
Closes: https://bugzilla.kernel.org/show_bug.cgi?id=215906
CC: stable@vger.kernel.org
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20250225095927.2512358-2-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
cdev->config might be NULL, so check it before dereferencing.
CC: stable <stable@kernel.org>
Fixes: 40e89ff5750f ("usb: gadget: Set self-powered based on MaxPower and bmAttributes")
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Link: https://lore.kernel.org/r/20250220120314.3614330-1-m.szyprowski@samsung.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
It is observed that on some systems an initial PPM reset during the boot
phase can trigger a timeout:
[ 6.482546] ucsi_acpi USBC000:00: failed to reset PPM!
[ 6.482551] ucsi_acpi USBC000:00: error -ETIMEDOUT: PPM init failed
Still, increasing the timeout value, albeit being the most straightforward
solution, eliminates the problem: the initial PPM reset may take up to
~8000-10000ms on some Lenovo laptops. When it is reset after the above
period of time (or even if ucsi_reset_ppm() is not called overall), UCSI
works as expected.
Moreover, if the ucsi_acpi module is loaded/unloaded manually after the
system has booted, reading the CCI values and resetting the PPM works
perfectly, without any timeout. Thus it's only a boot-time issue.
The reason for this behavior is not clear but it may be the consequence
of some tricks that the firmware performs or be an actual firmware bug.
As a workaround, increase the timeout to avoid failing the UCSI
initialization prematurely.
Fixes: b1b59e16075f ("usb: typec: ucsi: Increase command completion timeout value")
Cc: stable <stable@kernel.org>
Signed-off-by: Fedor Pchelkin <boddah8794@gmail.com>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Link: https://lore.kernel.org/r/20250217105442.113486-3-boddah8794@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
For the ACPI backend of UCSI the UCSI "registers" are just a memory copy
of the register values in an opregion. The ACPI implementation in the
BIOS ensures that the opregion contents are synced to the embedded
controller and it ensures that the registers (in particular CCI) are
synced back to the opregion on notifications. While there is an ACPI call
that syncs the actual registers to the opregion there is rarely a need to
do this and on some ACPI implementations it actually breaks in various
interesting ways.
The only reason to force a sync from the embedded controller is to poll
CCI while notifications are disabled. Only the ucsi core knows if this
is the case and guessing based on the current command is suboptimal, i.e.
leading to the following spurious assertion splat:
WARNING: CPU: 3 PID: 76 at drivers/usb/typec/ucsi/ucsi.c:1388 ucsi_reset_ppm+0x1b4/0x1c0 [typec_ucsi]
CPU: 3 UID: 0 PID: 76 Comm: kworker/3:0 Not tainted 6.12.11-200.fc41.x86_64 #1
Hardware name: LENOVO 21D0/LNVNB161216, BIOS J6CN45WW 03/17/2023
Workqueue: events_long ucsi_init_work [typec_ucsi]
RIP: 0010:ucsi_reset_ppm+0x1b4/0x1c0 [typec_ucsi]
Call Trace:
<TASK>
ucsi_init_work+0x3c/0xac0 [typec_ucsi]
process_one_work+0x179/0x330
worker_thread+0x252/0x390
kthread+0xd2/0x100
ret_from_fork+0x34/0x50
ret_from_fork_asm+0x1a/0x30
</TASK>
Thus introduce a ->poll_cci() method that works like ->read_cci() with an
additional forced sync and document that this should be used when polling
with notifications disabled. For all other backends that presumably don't
have this issue use the same implementation for both methods.
Fixes: fa48d7e81624 ("usb: typec: ucsi: Do not call ACPI _DSM method for UCSI read operations")
Cc: stable <stable@kernel.org>
Signed-off-by: Christian A. Ehrhardt <lk@c--e.de>
Tested-by: Fedor Pchelkin <boddah8794@gmail.com>
Signed-off-by: Fedor Pchelkin <boddah8794@gmail.com>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Link: https://lore.kernel.org/r/20250217105442.113486-2-boddah8794@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
During probe, the TCPC alert interrupts are getting masked to
avoid unwanted interrupts during chip setup: this is ok to do
but there is no unmasking happening at any later time, which
means that the chip will not raise any interrupt, essentially
making it not functional as, while internally it does perform
all of the intended functions, it won't signal anything to the
outside.
Unmask the alert interrupts to fix functionality.
Fixes: ce08eaeb6388 ("staging: typec: rt1711h typec chip driver")
Cc: stable <stable@kernel.org>
Signed-off-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Link: https://lore.kernel.org/r/20250219114700.41700-1-angelogioacchino.delregno@collabora.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Currently the USB gadget will be set as bus-powered based solely
on whether its bMaxPower is greater than 100mA, but this may miss
devices that may legitimately draw less than 100mA but still want
to report as bus-powered. Similarly during suspend & resume, USB
gadget is incorrectly marked as bus/self powered without checking
the bmAttributes field. Fix these by configuring the USB gadget
as self or bus powered based on bmAttributes, and explicitly set
it as bus-powered if it draws more than 100mA.
Cc: stable <stable@kernel.org>
Fixes: 5e5caf4fa8d3 ("usb: gadget: composite: Inform controller driver of self-powered")
Signed-off-by: Prashanth K <prashanth.k@oss.qualcomm.com>
Link: https://lore.kernel.org/r/20250217120328.2446639-1-prashanth.k@oss.qualcomm.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Currently while UDC suspends, u_ether attempts to remote wakeup
the host if there are any pending transfers. However, if remote
wakeup fails, the UDC remains suspended but the is_suspend flag
is not set. And since is_suspend flag isn't set, the subsequent
eth_start_xmit() would queue USB requests to suspended UDC.
To fix this, bail out from gether_suspend() only if remote wakeup
operation is successful.
Cc: stable <stable@kernel.org>
Fixes: 0a1af6dfa077 ("usb: gadget: f_ecm: Add suspend/resume and remote wakeup support")
Signed-off-by: Prashanth K <prashanth.k@oss.qualcomm.com>
Link: https://lore.kernel.org/r/20250212100840.3812153-1-prashanth.k@oss.qualcomm.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Syzbot once again identified a flaw in usb endpoint checking, see [1].
This time the issue stems from a commit authored by me (2eabb655a968
("usb: atm: cxacru: fix endpoint checking in cxacru_bind()")).
While using usb_find_common_endpoints() may usually be enough to
discard devices with wrong endpoints, in this case one needs more
than just finding and identifying the sufficient number of endpoints
of correct types - one needs to check the endpoint's address as well.
Since cxacru_bind() fills URBs with CXACRU_EP_CMD address in mind,
switch the endpoint verification approach to usb_check_XXX_endpoints()
instead to fix incomplete ep testing.
[1] Syzbot report:
usb 5-1: BOGUS urb xfer, pipe 3 != type 1
WARNING: CPU: 0 PID: 1378 at drivers/usb/core/urb.c:504 usb_submit_urb+0xc4e/0x18c0 drivers/usb/core/urb.c:503
...
RIP: 0010:usb_submit_urb+0xc4e/0x18c0 drivers/usb/core/urb.c:503
...
Call Trace:
<TASK>
cxacru_cm+0x3c8/0xe50 drivers/usb/atm/cxacru.c:649
cxacru_card_status drivers/usb/atm/cxacru.c:760 [inline]
cxacru_bind+0xcf9/0x1150 drivers/usb/atm/cxacru.c:1223
usbatm_usb_probe+0x314/0x1d30 drivers/usb/atm/usbatm.c:1058
cxacru_usb_probe+0x184/0x220 drivers/usb/atm/cxacru.c:1377
usb_probe_interface+0x641/0xbb0 drivers/usb/core/driver.c:396
really_probe+0x2b9/0xad0 drivers/base/dd.c:658
__driver_probe_device+0x1a2/0x390 drivers/base/dd.c:800
driver_probe_device+0x50/0x430 drivers/base/dd.c:830
...
Reported-and-tested-by: syzbot+ccbbc229a024fa3e13b5@syzkaller.appspotmail.com
Closes: https://syzkaller.appspot.com/bug?extid=ccbbc229a024fa3e13b5
Fixes: 2eabb655a968 ("usb: atm: cxacru: fix endpoint checking in cxacru_bind()")
Cc: stable@kernel.org
Signed-off-by: Nikita Zhandarovich <n.zhandarovich@fintech.ru>
Link: https://lore.kernel.org/r/20250213122259.730772-1-n.zhandarovich@fintech.ru
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
As PD2.0 spec ("6.5.6.2 PSSourceOffTimer")，the PSSourceOffTimer is
used by the Policy Engine in Dual-Role Power device that is currently
acting as a Sink to timeout on a PS_RDY Message during a Power Role
Swap sequence. This condition leads to a Hard Reset for USB Type-A and
Type-B Plugs and Error Recovery for Type-C plugs and return to USB
Default Operation.
Therefore, after PSSourceOffTimer timeout, the tcpm state machine should
switch from PR_SWAP_SNK_SRC_SINK_OFF to ERROR_RECOVERY. This can also
solve the test items in the USB power delivery compliance test:
TEST.PD.PROT.SNK.12 PR_Swap – PSSourceOffTimer Timeout
[1] https://usb.org/document-library/usb-power-delivery-compliance-test-specification-0/USB_PD3_CTS_Q4_2025_OR.zip
Fixes: f0690a25a140 ("staging: typec: USB Type-C Port Manager (tcpm)")
Cc: stable <stable@kernel.org>
Signed-off-by: Jos Wang <joswang@lenovo.com>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Tested-by: Amit Sunil Dhamne <amitsd@google.com>
Link: https://lore.kernel.org/r/20250213134921.3798-1-joswang1221@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
The role switch registration and set_role() can happen in parallel as they
are invoked independent of each other. There is a possibility that a driver
might spend significant amount of time in usb_role_switch_register() API
due to the presence of time intensive operations like component_add()
which operate under common mutex. This leads to a time window after
allocating the switch and before setting the registered flag where the set
role notifications are dropped. Below timeline summarizes this behavior
Thread1 | Thread2
usb_role_switch_register() |
| |
---> allocate switch |
| |
---> component_add() | usb_role_switch_set_role()
| | |
| | --> Drop role notifications
| | since sw->registered
| | flag is not set.
| |
--->Set registered flag.|
To avoid this, set the registered flag early on in the switch register
API.
Fixes: b787a3e78175 ("usb: roles: don't get/set_role() when usb_role_switch is unregistered")
Cc: stable <stable@kernel.org>
Signed-off-by: Elson Roy Serrao <quic_eserrao@quicinc.com>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Link: https://lore.kernel.org/r/20250206193950.22421-1-quic_eserrao@quicinc.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
The behaviour of kthread_create_worker() was recently changed to align
with the one of kthread_create(). The kthread worker is created but not
awaken by default. This is to allow the use of kthread_affine_preferred()
and kthread_bind[_mask]() with kthread workers. In order to keep the
old behaviour and wake the kthread up, kthread_run_worker() must be
used. All the pre-existing users have been converted, except for UVC
that was introduced in the same merge window as the API change.
This results in hangs:
INFO: task UVCG:82 blocked for more than 491 seconds.
Tainted: G T 6.13.0-rc2-00014-gb04e317b5226 #1
task:UVCG state:D stack:0 pid:82
Call Trace:
__schedule
schedule
schedule_preempt_disabled
kthread
? kthread_flush_work
ret_from_fork
ret_from_fork_asm
entry_INT80_32
Fix this with converting UVCG kworker to the new API.
Reported-by: kernel test robot <oliver.sang@intel.com>
Closes: https://lore.kernel.org/oe-lkp/202502121025.55bfa801-lkp@intel.com
Fixes: f0bbfbd16b3b ("usb: gadget: uvc: rework to enqueue in pump worker from encoded queue")
Cc: stable <stable@kernel.org>
Cc: Michael Grzeschik <m.grzeschik@pengutronix.de>
Signed-off-by: Frederic Weisbecker <frederic@kernel.org>
Link: https://lore.kernel.org/r/20250212135514.30539-1-frederic@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Teclast disk used on Huawei hisi platforms doesn't work well,
losing connectivity intermittently if LPM is enabled.
Add quirk disable LPM to resolve the issue.
Signed-off-by: Lei Huang <huanglei@kylinos.cn>
Cc: stable <stable@kernel.org>
Link: https://lore.kernel.org/r/20250212093829.7379-1-huanglei814@163.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
device_del() can lead to new work being scheduled in gadget->work
workqueue. This is observed, for example, with the dwc3 driver with the
following call stack:
device_del()
gadget_unbind_driver()
usb_gadget_disconnect_locked()
dwc3_gadget_pullup()
dwc3_gadget_soft_disconnect()
usb_gadget_set_state()
schedule_work(&gadget->work)
Move flush_work() after device_del() to ensure the workqueue is cleaned
up.
Fixes: 5702f75375aa9 ("usb: gadget: udc-core: move sysfs_notify() to a workqueue")
Cc: stable <stable@kernel.org>
Signed-off-by: Roy Luo <royluo@google.com>
Reviewed-by: Alan Stern <stern@rowland.harvard.edu>
Reviewed-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com>
Link: https://lore.kernel.org/r/20250204233642.666991-1-royluo@google.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
When using USB MIDI, a lock is attempted to be acquired twice through a
re-entrant call to f_midi_transmit, causing a deadlock.
Fix it by using queue_work() to schedule the inner f_midi_transmit() via
a high priority work queue from the completion handler.
Link: https://lore.kernel.org/all/CAArt=LjxU0fUZOj06X+5tkeGT+6RbXzpWg1h4t4Fwa_KGVAX6g@mail.gmail.com/
Fixes: d5daf49b58661 ("USB: gadget: midi: add midi function driver")
Cc: stable <stable@kernel.org>
Signed-off-by: Jill Donahue <jilliandonahue58@gmail.com>
Link: https://lore.kernel.org/r/20250211174805.1369265-1-jdonahue@fender.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
When usb_control_msg is used in the get_bMaxPacketSize0 function, the
USB pipe does not include the endpoint device number. This can cause
failures when a usb hub port is reinitialized after encountering a bad
cable connection. As a result, the system logs the following error
messages:
usb usb2-port1: cannot reset (err = -32)
usb usb2-port1: Cannot enable. Maybe the USB cable is bad?
usb usb2-port1: attempt power cycle
usb 2-1: new high-speed USB device number 5 using ci_hdrc
usb 2-1: device descriptor read/8, error -71
The problem began after commit 85d07c556216 ("USB: core: Unite old
scheme and new scheme descriptor reads"). There
usb_get_device_descriptor was replaced with get_bMaxPacketSize0. Unlike
usb_get_device_descriptor, the get_bMaxPacketSize0 function uses the
macro usb_rcvaddr0pipe, which does not include the endpoint device
number. usb_get_device_descriptor, on the other hand, used the macro
usb_rcvctrlpipe, which includes the endpoint device number.
By modifying the get_bMaxPacketSize0 function to use usb_rcvctrlpipe
instead of usb_rcvaddr0pipe, the issue can be resolved. This change will
ensure that the endpoint device number is included in the USB pipe,
preventing reinitialization failures. If the endpoint has not set the
device number yet, it will still work because the device number is 0 in
udev.
Cc: stable <stable@kernel.org>
Fixes: 85d07c556216 ("USB: core: Unite old scheme and new scheme descriptor reads")
Signed-off-by: Stefan Eichenberger <stefan.eichenberger@toradex.com>
Reviewed-by: Alan Stern <stern@rowland.harvard.edu>
Link: https://lore.kernel.org/r/20250203105840.17539-1-eichest@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
There is a frequent timeout during controller enter/exit from halt state
after toggling the run_stop bit by SW. This timeout occurs when
performing frequent role switches between host and device, causing
device enumeration issues due to the timeout. This issue was not present
when USB2 suspend PHY was disabled by passing the SNPS quirks
(snps,dis_u2_susphy_quirk and snps,dis_enblslpm_quirk) from the DTS.
However, there is a requirement to enable USB2 suspend PHY by setting of
GUSB2PHYCFG.ENBLSLPM and GUSB2PHYCFG.SUSPHY bits when controller starts
in gadget or host mode results in the timeout issue.
This commit addresses this timeout issue by ensuring that the bits
GUSB2PHYCFG.ENBLSLPM and GUSB2PHYCFG.SUSPHY are cleared before starting
the dwc3_gadget_run_stop sequence and restoring them after the
dwc3_gadget_run_stop sequence is completed.
Fixes: 72246da40f37 ("usb: Introduce DesignWare USB3 DRD Driver")
Cc: stable <stable@kernel.org>
Signed-off-by: Selvarasu Ganesan <selvarasu.g@samsung.com>
Acked-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com>
Link: https://lore.kernel.org/r/20250201163903.459-1-selvarasu.g@samsung.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
The fastboot tool for communicating with Android bootloaders does not
work reliably with this device if USB 2 Link Power Management (LPM)
is enabled.
Various fastboot commands are affected, including the
following, which usually reproduces the problem within two tries:
fastboot getvar kernel
getvar:kernel FAILED (remote: 'GetVar Variable Not found')
This issue was hidden on many systems up until commit 63a1f8454962
("xhci: stored cached port capability values in one place") as the xhci
driver failed to detect USB 2 LPM support if USB 3 ports were listed
before USB 2 ports in the "supported protocol capabilities".
Adding the quirk resolves the issue. No drawbacks are expected since
the device uses different USB product IDs outside of fastboot mode, and
since fastboot commands worked before, until LPM was enabled on the
tested system by the aforementioned commit.
Based on a patch from Forest <forestix@nom.one> from which most of the
code and commit message is taken.
Cc: stable <stable@kernel.org>
Reported-by: Forest <forestix@nom.one>
Closes: https://lore.kernel.org/hk8umj9lv4l4qguftdq1luqtdrpa1gks5l@sonic.net
Tested-by: Forest <forestix@nom.one>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20250206151836.51742-1-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Add Renesas R-Car D3 USB Download mode quirk and update comments
on all the other Renesas R-Car USB Download mode quirks to discern
them from each other. This follows R-Car Series, 3rd Generation
reference manual Rev.2.00 chapter 19.2.8 USB download mode .
Fixes: 6d853c9e4104 ("usb: cdc-acm: Add DISABLE_ECHO for Renesas USB Download mode")
Cc: stable <stable@kernel.org>
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/r/20250209145708.106914-1-marek.vasut+renesas@mailbox.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
If we receive an initial fragment of size 8 bytes which specifies a wLength
of 1 byte (so the reassembled message is supposed to be 9 bytes long), and
we then receive a second fragment of size 9 bytes (which is not supposed to
happen), we currently wrongly bypass the fragment reassembly code but still
pass the pointer to the acm->notification_buffer to
acm_process_notification().
Make this less wrong by always going through fragment reassembly when we
expect more fragments.
Before this patch, receiving an overlong fragment could lead to `newctrl`
in acm_process_notification() being uninitialized data (instead of data
coming from the device).
Cc: stable <stable@kernel.org>
Fixes: ea2583529cd1 ("cdc-acm: reassemble fragmented notifications")
Signed-off-by: Jann Horn <jannh@google.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
If the first fragment is shorter than struct usb_cdc_notification, we can't
calculate an expected_size. Log an error and discard the notification
instead of reading lengths from memory outside the received data, which can
lead to memory corruption when the expected_size decreases between
fragments, causing `expected_size - acm->nb_index` to wrap.
This issue has been present since the beginning of git history; however,
it only leads to memory corruption since commit ea2583529cd1
("cdc-acm: reassemble fragmented notifications").
A mitigating factor is that acm_ctrl_irq() can only execute after userspace
has opened /dev/ttyACM*; but if ModemManager is running, ModemManager will
do that automatically depending on the USB device's vendor/product IDs and
its other interfaces.
Cc: stable <stable@kernel.org>
Fixes: 1da177e4c3f4 ("Linux-2.6.12-rc2")
Signed-off-by: Jann Horn <jannh@google.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Some Renesas HCs require firmware upload to work, this is handled by the
xhci_pci_renesas driver. Other variants of those chips load firmware from
a SPI flash and are ready to work with xhci_pci alone.
A refactor merged in v6.12 broke the latter configuration so that users
are finding their hardware ignored by the normal driver and are forced to
enable the firmware loader which isn't really necessary on their systems.
Let xhci_pci work with those chips as before when the firmware loader is
disabled by kernel configuration.
Fixes: 25f51b76f90f ("xhci-pci: Make xhci-pci-renesas a proper modular driver")
Cc: stable <stable@kernel.org>
Closes: https://bugzilla.kernel.org/show_bug.cgi?id=219616
Closes: https://bugzilla.kernel.org/show_bug.cgi?id=219726
Signed-off-by: Michal Pecio <michal.pecio@gmail.com>
Tested-by: Nicolai Buchwitz <nb@tipi-net.de>
Link: https://lore.kernel.org/r/20250128104529.58a79bfc@foxbook
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
LS7A EHCI controller doesn't have extended capabilities, so the EECP
(EHCI Extended Capabilities Pointer) field of HCCPARAMS register should
be 0x0, but it reads as 0xa0 now. This is a hardware flaw and will be
fixed in future, now just clear the EECP field to avoid error messages
on boot:
......
[ 0.581675] pci 0000:00:04.1: EHCI: unrecognized capability ff
[ 0.581699] pci 0000:00:04.1: EHCI: unrecognized capability ff
[ 0.581716] pci 0000:00:04.1: EHCI: unrecognized capability ff
[ 0.581851] pci 0000:00:04.1: EHCI: unrecognized capability ff
......
[ 0.581916] pci 0000:00:05.1: EHCI: unrecognized capability ff
[ 0.581951] pci 0000:00:05.1: EHCI: unrecognized capability ff
[ 0.582704] pci 0000:00:05.1: EHCI: unrecognized capability ff
[ 0.582799] pci 0000:00:05.1: EHCI: unrecognized capability ff
......
Cc: stable <stable@kernel.org>
Signed-off-by: Baoqi Zhang <zhangbaoqi@loongson.cn>
Signed-off-by: Huacai Chen <chenhuacai@loongson.cn>
Link: https://lore.kernel.org/r/20250202124935.480500-1-chenhuacai@loongson.cn
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
ssh://gitolite.kernel.org/pub/scm/linux/kernel/git/johan/usb-serial into usb-linus
Johan writes:
USB-serial device ids for 6.14-rc3
Here are some new modem device ids and a couple of related cleanups of
the device id table.
All have been in linux-next with no reported issues.
* tag 'usb-serial-6.14-rc3' of ssh://gitolite.kernel.org/pub/scm/linux/kernel/git/johan/usb-serial:
USB: serial: option: drop MeiG Smart defines
USB: serial: option: fix Telit Cinterion FN990A name
USB: serial: option: add Telit Cinterion FN990B compositions
USB: serial: option: add MeiG Smart SLM828
|
|
Several MeiG Smart modems apparently use the same product id, making the
defines even less useful.
Drop them in favour of using comments consistently to make the id table
slightly less unwieldy.
Cc: stable@vger.kernel.org
Acked-by: Chester A. Unal <chester.a.unal@arinc9.com>
Signed-off-by: Johan Hovold <johan@kernel.org>
|
|
The correct name for FN990 is FN990A so use it in order to avoid
confusion with FN990B.
Signed-off-by: Fabio Porcedda <fabio.porcedda@gmail.com>
Cc: stable@vger.kernel.org
Signed-off-by: Johan Hovold <johan@kernel.org>
|
|
Add the following Telit Cinterion FN990B40 compositions:
0x10d0: rmnet + tty (AT/NMEA) + tty (AT) + tty (AT) + tty (AT) +
tty (diag) + DPL + QDSS (Qualcomm Debug SubSystem) + adb
T: Bus=01 Lev=01 Prnt=01 Port=01 Cnt=01 Dev#= 17 Spd=480 MxCh= 0
D: Ver= 2.10 Cls=00(>ifc ) Sub=00 Prot=00 MxPS=64 #Cfgs= 1
P: Vendor=1bc7 ProdID=10d0 Rev=05.15
S: Manufacturer=Telit Cinterion
S: Product=FN990
S: SerialNumber=43b38f19
C: #Ifs= 9 Cfg#= 1 Atr=e0 MxPwr=500mA
I: If#= 0 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=ff Prot=50 Driver=qmi_wwan
E: Ad=01(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=81(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=82(I) Atr=03(Int.) MxPS= 8 Ivl=32ms
I: If#= 1 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=ff Prot=60 Driver=option
E: Ad=02(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=83(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=84(I) Atr=03(Int.) MxPS= 10 Ivl=32ms
I: If#= 2 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=ff Prot=40 Driver=option
E: Ad=03(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=85(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=86(I) Atr=03(Int.) MxPS= 10 Ivl=32ms
I: If#= 3 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=ff Prot=40 Driver=option
E: Ad=04(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=87(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=88(I) Atr=03(Int.) MxPS= 10 Ivl=32ms
I: If#= 4 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=ff Prot=40 Driver=option
E: Ad=05(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=89(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=8a(I) Atr=03(Int.) MxPS= 10 Ivl=32ms
I: If#= 5 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=30 Driver=option
E: Ad=06(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=8b(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
I: If#= 6 Alt= 0 #EPs= 1 Cls=ff(vend.) Sub=ff Prot=80 Driver=(none)
E: Ad=8c(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
I: If#= 7 Alt= 0 #EPs= 1 Cls=ff(vend.) Sub=ff Prot=70 Driver=(none)
E: Ad=8d(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
I: If#= 8 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=42 Prot=01 Driver=usbfs
E: Ad=07(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=8e(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
0x10d1: MBIM + tty (AT/NMEA) + tty (AT) + tty (AT) + tty (AT) +
tty (diag) + DPL + QDSS (Qualcomm Debug SubSystem) + adb
T: Bus=01 Lev=01 Prnt=01 Port=01 Cnt=01 Dev#= 16 Spd=480 MxCh= 0
D: Ver= 2.10 Cls=00(>ifc ) Sub=00 Prot=00 MxPS=64 #Cfgs= 1
P: Vendor=1bc7 ProdID=10d1 Rev=05.15
S: Manufacturer=Telit Cinterion
S: Product=FN990
S: SerialNumber=43b38f19
C: #Ifs=10 Cfg#= 1 Atr=e0 MxPwr=500mA
I: If#= 0 Alt= 0 #EPs= 1 Cls=02(commc) Sub=0e Prot=00 Driver=cdc_mbim
E: Ad=82(I) Atr=03(Int.) MxPS= 64 Ivl=32ms
I: If#= 1 Alt= 1 #EPs= 2 Cls=0a(data ) Sub=00 Prot=02 Driver=cdc_mbim
E: Ad=01(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=81(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
I: If#= 2 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=ff Prot=60 Driver=option
E: Ad=02(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=83(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=84(I) Atr=03(Int.) MxPS= 10 Ivl=32ms
I: If#= 3 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=ff Prot=40 Driver=option
E: Ad=03(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=85(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=86(I) Atr=03(Int.) MxPS= 10 Ivl=32ms
I: If#= 4 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=ff Prot=40 Driver=option
E: Ad=04(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=87(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=88(I) Atr=03(Int.) MxPS= 10 Ivl=32ms
I: If#= 5 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=ff Prot=40 Driver=option
E: Ad=05(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=89(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=8a(I) Atr=03(Int.) MxPS= 10 Ivl=32ms
I: If#= 6 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=30 Driver=option
E: Ad=06(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=8b(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
I: If#= 7 Alt= 0 #EPs= 1 Cls=ff(vend.) Sub=ff Prot=80 Driver=(none)
E: Ad=8c(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
I: If#= 8 Alt= 0 #EPs= 1 Cls=ff(vend.) Sub=ff Prot=70 Driver=(none)
E: Ad=8d(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
I: If#= 9 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=42 Prot=01 Driver=usbfs
E: Ad=07(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=8e(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
0x10d2: RNDIS + tty (AT/NMEA) + tty (AT) + tty (AT) + tty (AT) +
tty (diag) + DPL + QDSS (Qualcomm Debug SubSystem) + adb
T: Bus=01 Lev=01 Prnt=01 Port=01 Cnt=01 Dev#= 18 Spd=480 MxCh= 0
D: Ver= 2.10 Cls=00(>ifc ) Sub=00 Prot=00 MxPS=64 #Cfgs= 1
P: Vendor=1bc7 ProdID=10d2 Rev=05.15
S: Manufacturer=Telit Cinterion
S: Product=FN990
S: SerialNumber=43b38f19
C: #Ifs=10 Cfg#= 1 Atr=e0 MxPwr=500mA
I: If#= 0 Alt= 0 #EPs= 1 Cls=ef(misc ) Sub=04 Prot=01 Driver=rndis_host
E: Ad=82(I) Atr=03(Int.) MxPS= 8 Ivl=32ms
I: If#= 1 Alt= 0 #EPs= 2 Cls=0a(data ) Sub=00 Prot=00 Driver=rndis_host
E: Ad=01(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=81(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
I: If#= 2 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=ff Prot=60 Driver=option
E: Ad=02(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=83(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=84(I) Atr=03(Int.) MxPS= 10 Ivl=32ms
I: If#= 3 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=ff Prot=40 Driver=option
E: Ad=03(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=85(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=86(I) Atr=03(Int.) MxPS= 10 Ivl=32ms
I: If#= 4 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=ff Prot=40 Driver=option
E: Ad=04(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=87(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=88(I) Atr=03(Int.) MxPS= 10 Ivl=32ms
I: If#= 5 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=ff Prot=40 Driver=option
E: Ad=05(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=89(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=8a(I) Atr=03(Int.) MxPS= 10 Ivl=32ms
I: If#= 6 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=30 Driver=option
E: Ad=06(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=8b(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
I: If#= 7 Alt= 0 #EPs= 1 Cls=ff(vend.) Sub=ff Prot=80 Driver=(none)
E: Ad=8c(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
I: If#= 8 Alt= 0 #EPs= 1 Cls=ff(vend.) Sub=ff Prot=70 Driver=(none)
E: Ad=8d(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
I: If#= 9 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=42 Prot=01 Driver=usbfs
E: Ad=07(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=8e(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
0x10d3: ECM + tty (AT/NMEA) + tty (AT) + tty (AT) + tty (AT) +
tty (diag) + DPL + QDSS (Qualcomm Debug SubSystem) + adb
T: Bus=01 Lev=01 Prnt=01 Port=01 Cnt=01 Dev#= 20 Spd=480 MxCh= 0
D: Ver= 2.10 Cls=00(>ifc ) Sub=00 Prot=00 MxPS=64 #Cfgs= 1
P: Vendor=1bc7 ProdID=10d3 Rev=05.15
S: Manufacturer=Telit Cinterion
S: Product=FN990
S: SerialNumber=43b38f19
C: #Ifs=10 Cfg#= 1 Atr=e0 MxPwr=500mA
I: If#= 0 Alt= 0 #EPs= 1 Cls=02(commc) Sub=06 Prot=00 Driver=cdc_ether
E: Ad=82(I) Atr=03(Int.) MxPS= 16 Ivl=32ms
I: If#= 1 Alt= 1 #EPs= 2 Cls=0a(data ) Sub=00 Prot=00 Driver=cdc_ether
E: Ad=01(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=81(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
I: If#= 2 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=ff Prot=60 Driver=option
E: Ad=02(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=83(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=84(I) Atr=03(Int.) MxPS= 10 Ivl=32ms
I: If#= 3 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=ff Prot=40 Driver=option
E: Ad=03(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=85(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=86(I) Atr=03(Int.) MxPS= 10 Ivl=32ms
I: If#= 4 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=ff Prot=40 Driver=option
E: Ad=04(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=87(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=88(I) Atr=03(Int.) MxPS= 10 Ivl=32ms
I: If#= 5 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=ff Prot=40 Driver=option
E: Ad=05(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=89(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=8a(I) Atr=03(Int.) MxPS= 10 Ivl=32ms
I: If#= 6 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=30 Driver=option
E: Ad=06(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=8b(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
I: If#= 7 Alt= 0 #EPs= 1 Cls=ff(vend.) Sub=ff Prot=80 Driver=(none)
E: Ad=8c(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
I: If#= 8 Alt= 0 #EPs= 1 Cls=ff(vend.) Sub=ff Prot=70 Driver=(none)
E: Ad=8d(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
I: If#= 9 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=42 Prot=01 Driver=usbfs
E: Ad=07(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=8e(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
Cc: stable@vger.kernel.org
Signed-off-by: Fabio Porcedda <fabio.porcedda@gmail.com>
Reviewed-by: Daniele Palmas <dnlplm@gmail.com>
Signed-off-by: Johan Hovold <johan@kernel.org>
|
|
MeiG Smart SLM828 is an LTE-A CAT6 modem with the mPCIe form factor. The
"Cls=ff(vend.) Sub=10 Prot=02" and "Cls=ff(vend.) Sub=10 Prot=03"
interfaces respond to AT commands. Add these interfaces.
The product ID the modem uses is shared across multiple modems. Therefore,
add comments to describe which interface is used for which modem.
T: Bus=01 Lev=01 Prnt=05 Port=01 Cnt=01 Dev#= 6 Spd=480 MxCh= 0
D: Ver= 2.10 Cls=00(>ifc ) Sub=00 Prot=00 MxPS=64 #Cfgs= 1
P: Vendor=2dee ProdID=4d22 Rev=05.04
S: Manufacturer=MEIG
S: Product=LTE-A Module
S: SerialNumber=4da7ec42
C: #Ifs= 6 Cfg#= 1 Atr=80 MxPwr=500mA
I: If#= 0 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=10 Prot=01 Driver=(none)
E: Ad=01(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=81(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
I: If#= 1 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=10 Prot=02 Driver=(none)
E: Ad=02(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=82(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=83(I) Atr=03(Int.) MxPS= 10 Ivl=32ms
I: If#= 2 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=10 Prot=03 Driver=(none)
E: Ad=03(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=84(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=85(I) Atr=03(Int.) MxPS= 10 Ivl=32ms
I: If#= 3 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=10 Prot=04 Driver=(none)
E: Ad=04(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=86(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=87(I) Atr=03(Int.) MxPS= 10 Ivl=32ms
I: If#= 4 Alt= 0 #EPs= 1 Cls=ff(vend.) Sub=ff Prot=ff Driver=(none)
E: Ad=88(I) Atr=03(Int.) MxPS= 64 Ivl=32ms
I: If#= 5 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=10 Prot=05 Driver=qmi_wwan
E: Ad=0f(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=89(I) Atr=03(Int.) MxPS= 8 Ivl=32ms
E: Ad=8e(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
Signed-off-by: Chester A. Unal <chester.a.unal@arinc9.com>
Link: https://lore.kernel.org/20250124-for-johan-meig-slm828-v2-1-6b4cd3f6344f@arinc9.com
Cc: stable@vger.kernel.org
Signed-off-by: Johan Hovold <johan@kernel.org>
|
|
While the MIDI jacks are configured correctly, and the MIDIStreaming
endpoint descriptors are filled with the correct information,
bNumEmbMIDIJack and bLength are set incorrectly in these descriptors.
This does not matter when the numbers of in and out ports are equal, but
when they differ the host will receive broken descriptors with
uninitialized stack memory leaking into the descriptor for whichever
value is smaller.
The precise meaning of "in" and "out" in the port counts is not clearly
defined and can be confusing. But elsewhere the driver consistently
uses this to match the USB meaning of IN and OUT viewed from the host,
so that "in" ports send data to the host and "out" ports receive data
from it.
Cc: stable <stable@kernel.org>
Fixes: c8933c3f79568 ("USB: gadget: f_midi: allow a dynamic number of input and output ports")
Signed-off-by: John Keeping <jkeeping@inmusicbrands.com>
Reviewed-by: Takashi Iwai <tiwai@suse.de>
Link: https://lore.kernel.org/r/20250130195035.3883857-1-jkeeping@inmusicbrands.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
In dwc2_hsotg_udc_start(), e.g. when binding composite driver, "of_node"
is set to hsotg->dev->of_node.
It causes errors when binding the gadget driver several times, on
stm32mp157c-ev1 board. Below error is seen:
"pin PA10 already requested by 49000000.usb-otg; cannot claim for gadget.0"
The first time, no issue is seen as when registering the driver, of_node
isn't NULL:
-> gadget_dev_desc_UDC_store
-> usb_gadget_register_driver_owner
-> driver_register
...
-> really_probe -> pinctrl_bind_pins (no effect)
Then dwc2_hsotg_udc_start() sets of_node.
The second time (stop the gadget, reconfigure it, then start it again),
of_node has been set, so the probing code tries to acquire pins for the
gadget. These pins are hold by the controller, hence the error.
So clear gadget.dev.of_node in udc_stop() routine to avoid the issue.
Fixes: 7d7b22928b90 ("usb: gadget: s3c-hsotg: Propagate devicetree to gadget drivers")
Cc: stable <stable@kernel.org>
Signed-off-by: Fabrice Gasnier <fabrice.gasnier@foss.st.com>
Link: https://lore.kernel.org/r/20250124173325.2747710-1-fabrice.gasnier@foss.st.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Robert Morris created a test program which can cause
usb_hub_to_struct_hub() to dereference a NULL or inappropriate
pointer:
Oops: general protection fault, probably for non-canonical address
0xcccccccccccccccc: 0000 [#1] SMP DEBUG_PAGEALLOC PTI
CPU: 7 UID: 0 PID: 117 Comm: kworker/7:1 Not tainted 6.13.0-rc3-00017-gf44d154d6e3d #14
Hardware name: FreeBSD BHYVE/BHYVE, BIOS 14.0 10/17/2021
Workqueue: usb_hub_wq hub_event
RIP: 0010:usb_hub_adjust_deviceremovable+0x78/0x110
...
Call Trace:
<TASK>
? die_addr+0x31/0x80
? exc_general_protection+0x1b4/0x3c0
? asm_exc_general_protection+0x26/0x30
? usb_hub_adjust_deviceremovable+0x78/0x110
hub_probe+0x7c7/0xab0
usb_probe_interface+0x14b/0x350
really_probe+0xd0/0x2d0
? __pfx___device_attach_driver+0x10/0x10
__driver_probe_device+0x6e/0x110
driver_probe_device+0x1a/0x90
__device_attach_driver+0x7e/0xc0
bus_for_each_drv+0x7f/0xd0
__device_attach+0xaa/0x1a0
bus_probe_device+0x8b/0xa0
device_add+0x62e/0x810
usb_set_configuration+0x65d/0x990
usb_generic_driver_probe+0x4b/0x70
usb_probe_device+0x36/0xd0
The cause of this error is that the device has two interfaces, and the
hub driver binds to interface 1 instead of interface 0, which is where
usb_hub_to_struct_hub() looks.
We can prevent the problem from occurring by refusing to accept hub
devices that violate the USB spec by having more than one
configuration or interface.
Reported-and-tested-by: Robert Morris <rtm@csail.mit.edu>
Cc: stable <stable@kernel.org>
Closes: https://lore.kernel.org/linux-usb/95564.1737394039@localhost/
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Link: https://lore.kernel.org/r/c27f3bf4-63d8-4fb5-ac82-09e3cd19f61c@rowland.harvard.edu
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
drivers/usb/gadget/udc/renesas_usb3.c: In function 'renesas_usb3_probe':
drivers/usb/gadget/udc/renesas_usb3.c:2638:73: warning: '%d'
directive output may be truncated writing between 1 and 11 bytes into a
region of size 6 [-Wformat-truncation=]
2638 | snprintf(usb3_ep->ep_name, sizeof(usb3_ep->ep_name), "ep%d", i);
^~~~~~~~~~~~~~~~~~~~~~~~ ^~ ^
Fixes: 746bfe63bba3 ("usb: gadget: renesas_usb3: add support for Renesas USB3.0 peripheral controller")
Cc: stable@vger.kernel.org
Reported-by: kernel test robot <lkp@intel.com>
Closes: https://lore.kernel.org/oe-kbuild-all/202501201409.BIQPtkeB-lkp@intel.com/
Signed-off-by: Guo Ren <guoren@linux.alibaba.com>
Link: https://lore.kernel.org/r/20250122081231.47594-1-guoren@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Add missing description to the nostream_work of dwc3_ep. The work is
used by bulk multi-stream endpoints for a NoStream event to reinitiate
the stream if needed.
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
Closes: https://lore.kernel.org/linux-next/20250120182219.30dcb3c6@canb.auug.org.au/
Signed-off-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com>
Link: https://lore.kernel.org/r/7cdeaa346d24907712aac533c1c5f90a03151189.1737500936.git.Thinh.Nguyen@synopsys.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Since commit c141ecc3cecd7 ("of: Warn when of_property_read_bool() is
used on non-boolean properties") a warning is raised if this function
is used for property detection. of_property_present() is the correct
helper for this.
Signed-off-by: Alexander Stein <alexander.stein@ew.tq-group.com>
Link: https://lore.kernel.org/r/20250120144251.580981-1-alexander.stein@ew.tq-group.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
retries
The current implementation sets the wMaxPacketSize of bulk in/out
endpoints to 1024 bytes at the end of the f_midi_bind function. However,
in cases where there is a failure in the first midi bind attempt,
consider rebinding. This scenario may encounter an f_midi_bind issue due
to the previous bind setting the bulk endpoint's wMaxPacketSize to 1024
bytes, which exceeds the ep->maxpacket_limit where configured dwc3 TX/RX
FIFO's maxpacket size of 512 bytes for IN/OUT endpoints in support HS
speed only.
Here the term "rebind" in this context refers to attempting to bind the
MIDI function a second time in certain scenarios. The situations where
rebinding is considered include:
* When there is a failure in the first UDC write attempt, which may be
caused by other functions bind along with MIDI.
* Runtime composition change : Example : MIDI,ADB to MIDI. Or MIDI to
MIDI,ADB.
This commit addresses this issue by resetting the wMaxPacketSize before
endpoint claim. And here there is no need to reset all values in the usb
endpoint descriptor structure, as all members except wMaxPacketSize and
bEndpointAddress have predefined values.
This ensures that restores the endpoint to its expected configuration,
and preventing conflicts with value of ep->maxpacket_limit. It also
aligns with the approach used in other function drivers, which treat
endpoint descriptors as if they were full speed before endpoint claim.
Fixes: 46decc82ffd5 ("usb: gadget: unconditionally allocate hs/ss descriptor in bind operation")
Cc: stable@vger.kernel.org
Signed-off-by: Selvarasu Ganesan <selvarasu.g@samsung.com>
Link: https://lore.kernel.org/r/20250118060134.927-1-selvarasu.g@samsung.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core
Pull driver core and debugfs updates from Greg KH:
"Here is the big set of driver core and debugfs updates for 6.14-rc1.
Included in here is a bunch of driver core, PCI, OF, and platform rust
bindings (all acked by the different subsystem maintainers), hence the
merge conflict with the rust tree, and some driver core api updates to
mark things as const, which will also require some fixups due to new
stuff coming in through other trees in this merge window.
There are also a bunch of debugfs updates from Al, and there is at
least one user that does have a regression with these, but Al is
working on tracking down the fix for it. In my use (and everyone
else's linux-next use), it does not seem like a big issue at the
moment.
Here's a short list of the things in here:
- driver core rust bindings for PCI, platform, OF, and some i/o
functions.
We are almost at the "write a real driver in rust" stage now,
depending on what you want to do.
- misc device rust bindings and a sample driver to show how to use
them
- debugfs cleanups in the fs as well as the users of the fs api for
places where drivers got it wrong or were unnecessarily doing
things in complex ways.
- driver core const work, making more of the api take const * for
different parameters to make the rust bindings easier overall.
- other small fixes and updates
All of these have been in linux-next with all of the aforementioned
merge conflicts, and the one debugfs issue, which looks to be resolved
"soon""
* tag 'driver-core-6.14-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core: (95 commits)
rust: device: Use as_char_ptr() to avoid explicit cast
rust: device: Replace CString with CStr in property_present()
devcoredump: Constify 'struct bin_attribute'
devcoredump: Define 'struct bin_attribute' through macro
rust: device: Add property_present()
saner replacement for debugfs_rename()
orangefs-debugfs: don't mess with ->d_name
octeontx2: don't mess with ->d_parent or ->d_parent->d_name
arm_scmi: don't mess with ->d_parent->d_name
slub: don't mess with ->d_name
sof-client-ipc-flood-test: don't mess with ->d_name
qat: don't mess with ->d_name
xhci: don't mess with ->d_iname
mtu3: don't mess wiht ->d_iname
greybus/camera - stop messing with ->d_iname
mediatek: stop messing with ->d_iname
netdevsim: don't embed file_operations into your structs
b43legacy: make use of debugfs_get_aux()
b43: stop embedding struct file_operations into their objects
carl9170: stop embedding file_operations into their objects
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb
Pull USB / Thunderbolt driver updates from Greg KH:
"Here is the USB and Thunderbolt driver updates for 6.14-rc1. Nothing
huge in here, just lots of new hardware support and updates for
existing drivers. Changes here are:
- big gadget f_tcm driver update
- other gadget driver updates and fixes
- thunderbolt driver updates for new hardware and capabilities and
lots more debugging functionality to handle it when things aren't
working well.
- xhci driver updates
- new USB-serial device updates
- typec driver updates, including a chrome platform driver (acked by
the subsystem maintainers)
- other small driver updates
All of these have been in linux-next for a while with no reported
issues"
* tag 'usb-6.14-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb: (123 commits)
usb: hcd: Bump local buffer size in rh_string()
Revert "usb: gadget: u_serial: Disable ep before setting port to null to fix the crash caused by port being null"
usb: typec: tcpci: Prevent Sink disconnection before vPpsShutdown in SPR PPS
usb: xhci: tegra: Fix OF boolean read warning
usb: host: xhci-plat: add support compatible ID PNP0D15
usb: typec: ucsi: Add a macro definition for UCSI v1.0
usb: dwc3: core: Defer the probe until USB power supply ready
usbip: Correct format specifier for seqnum from %d to %u
usbip: Fix seqnum sign extension issue in vhci_tx_urb
dt-bindings: usb: snps,dwc3: Split core description
usb: quirks: Add NO_LPM quirk for TOSHIBA TransMemory-Mx device
usb: dwc3: gadget: Reinitiate stream for all host NoStream behavior
USB: Use str_enable_disable-like helpers
USB: gadget: Use str_enable_disable-like helpers
USB: phy: Use str_enable_disable-like helpers
USB: typec: Use str_enable_disable-like helpers
USB: host: Use str_enable_disable-like helpers
USB: Replace own str_plural with common one
USB: serial: quatech2: fix null-ptr-deref in qt2_process_read_urb()
usb: phy: Remove API devm_usb_put_phy()
...
|
|
Pull SCSI updates from James Bottomley:
"Updates to the usual drivers (ufs, lpfc, fnic, qla2xx, mpi3mr).
The major core change is the renaming of the slave_ methods plus a bit
of constification. The rest are minor updates and fixes"
* tag 'scsi-misc' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi: (103 commits)
scsi: fnic: Propagate SCSI error code from fnic_scsi_drv_init()
scsi: fnic: Test for memory allocation failure and return error code
scsi: fnic: Return appropriate error code from failure of scsi drv init
scsi: fnic: Return appropriate error code for mem alloc failure
scsi: fnic: Remove always-true IS_FNIC_FCP_INITIATOR macro
scsi: fnic: Fix use of uninitialized value in debug message
scsi: fnic: Delete incorrect debugfs error handling
scsi: fnic: Remove unnecessary else to fix warning in FDLS FIP
scsi: fnic: Remove extern definition from .c files
scsi: fnic: Remove unnecessary else and unnecessary break in FDLS
scsi: mpi3mr: Fix possible crash when setting up bsg fails
scsi: ufs: bsg: Set bsg_queue to NULL after removal
scsi: ufs: bsg: Delete bsg_dev when setting up bsg fails
scsi: st: Don't set pos_unknown just after device recognition
scsi: aic7xxx: Fix build 'aicasm' warning
scsi: Revert "scsi: ufs: core: Probe for EXT_IID support"
scsi: storvsc: Ratelimit warning logs to prevent VM denial of service
scsi: scsi_debug: Constify sdebug_driver_template
scsi: documentation: Corrections for struct updates
scsi: driver-api: documentation: Change what is added to docbook
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull ACPI updates from Rafael Wysocki:
"The most significant change here is replacing msleep() in
acpi_os_sleep() with usleep_range() to reduce spurious sleep time due
to timer inaccuracy which may spectacularly reduce the duration of
system suspend and resume transitions on some systems.
All of the other changes fall into the fixes and cleanups category
this time.
Specifics:
- Use usleep_range() instead of msleep() in acpi_os_sleep() to reduce
excessive delays due to timer inaccuracy, mostly affecting system
suspend and resume (Rafael Wysocki)
- Use str_enabled_disabled() string helpers in the ACPI tables
parsing code to make it easier to follow (Sunil V L)
- Update device properties parsing on systems using ACPI so that data
firmware nodes resulting from _DSD evaluation are treated as
available in firmware nodes walks (Sakari Ailus)
- Fix missing guid_t declaration in linux/prmt.h (Robert Richter)
- Update the GHES handling code to follow the global panic= policy
instead of overriding it by force-rebooting the system after a
fatal HW error has been reported (Borislav Petkov)
- Update messages printed by the ACPI battery driver to always refer
to driver extensions as "hooks" to avoid confusion with similar
functionality in the power supply subsystem in the future (Thomas
Weißschuh)
- Fix .probe() error path cleanup in the ACPI fan driver to avoid
memory leaks (Joe Hattori)
- Constify 'struct bin_attribute' in some places in the ACPI
subsystem and mark it as __ro_after_init in one place to prevent
binary blob attributes from being updated (Thomas Weißschuh)
- Add empty stubs for several ACPI-related symbols so that they can
be used when CONFIG_ACPI is unset and use them for removing
unnecessary conditional compilation from the ipu-bridge driver
(Ricardo Ribalda)"
* tag 'acpi-6.14-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
APEI: GHES: Have GHES honor the panic= setting
ACPI: PRM: Fix missing guid_t declaration in linux/prmt.h
ACPI: tables: Use string choice helpers
ACPI: property: Consider data nodes as being available
media: ipu-bridge: Remove unneeded conditional compilations
ACPI: bus: implement acpi_device_hid when !ACPI
ACPI: bus: implement for_each_acpi_consumer_dev when !ACPI
ACPI: header: implement acpi_device_handle when !ACPI
ACPI: bus: implement acpi_get_physical_device_location when !ACPI
ACPI: bus: implement for_each_acpi_dev_match when !ACPI
ACPI: bus: change the prototype for acpi_get_physical_device_location
ACPI: fan: cleanup resources in the error path of .probe()
ACPI: battery: Rename extensions to hook in messages
ACPI: OSL: Use usleep_range() in acpi_os_sleep()
ACPI: sysfs: Constify 'struct bin_attribute'
ACPI: BGRT: Constify 'struct bin_attribute'
ACPI: BGRT: Mark bin_attribute as __ro_after_init
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/frederic/linux-dynticks
Pull kthread updates from Frederic Weisbecker:
"Kthreads affinity follow either of 4 existing different patterns:
1) Per-CPU kthreads must stay affine to a single CPU and never
execute relevant code on any other CPU. This is currently handled
by smpboot code which takes care of CPU-hotplug operations.
Affinity here is a correctness constraint.
2) Some kthreads _have_ to be affine to a specific set of CPUs and
can't run anywhere else. The affinity is set through
kthread_bind_mask() and the subsystem takes care by itself to
handle CPU-hotplug operations. Affinity here is assumed to be a
correctness constraint.
3) Per-node kthreads _prefer_ to be affine to a specific NUMA node.
This is not a correctness constraint but merely a preference in
terms of memory locality. kswapd and kcompactd both fall into this
category. The affinity is set manually like for any other task and
CPU-hotplug is supposed to be handled by the relevant subsystem so
that the task is properly reaffined whenever a given CPU from the
node comes up. Also care should be taken so that the node affinity
doesn't cross isolated (nohz_full) cpumask boundaries.
4) Similar to the previous point except kthreads have a _preferred_
affinity different than a node. Both RCU boost kthreads and RCU
exp kworkers fall into this category as they refer to "RCU nodes"
from a distinctly distributed tree.
Currently the preferred affinity patterns (3 and 4) have at least 4
identified users, with more or less success when it comes to handle
CPU-hotplug operations and CPU isolation. Each of which do it in its
own ad-hoc way.
This is an infrastructure proposal to handle this with the following
API changes:
- kthread_create_on_node() automatically affines the created kthread
to its target node unless it has been set as per-cpu or bound with
kthread_bind[_mask]() before the first wake-up.
- kthread_affine_preferred() is a new function that can be called
right after kthread_create_on_node() to specify a preferred
affinity different than the specified node.
When the preferred affinity can't be applied because the possible
targets are offline or isolated (nohz_full), the kthread is affine to
the housekeeping CPUs (which means to all online CPUs most of the time
or only the non-nohz_full CPUs when nohz_full= is set).
kswapd, kcompactd, RCU boost kthreads and RCU exp kworkers have been
converted, along with a few old drivers.
Summary of the changes:
- Consolidate a bunch of ad-hoc implementations of
kthread_run_on_cpu()
- Introduce task_cpu_fallback_mask() that defines the default last
resort affinity of a task to become nohz_full aware
- Add some correctness check to ensure kthread_bind() is always
called before the first kthread wake up.
- Default affine kthread to its preferred node.
- Convert kswapd / kcompactd and remove their halfway working ad-hoc
affinity implementation
- Implement kthreads preferred affinity
- Unify kthread worker and kthread API's style
- Convert RCU kthreads to the new API and remove the ad-hoc affinity
implementation"
* tag 'kthread-for-6.14-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/frederic/linux-dynticks:
kthread: modify kernel-doc function name to match code
rcu: Use kthread preferred affinity for RCU exp kworkers
treewide: Introduce kthread_run_worker[_on_cpu]()
kthread: Unify kthread_create_on_cpu() and kthread_create_worker_on_cpu() automatic format
rcu: Use kthread preferred affinity for RCU boost
kthread: Implement preferred affinity
mm: Create/affine kswapd to its preferred node
mm: Create/affine kcompactd to its preferred node
kthread: Default affine kthread to its preferred NUMA node
kthread: Make sure kthread hasn't started while binding it
sched,arm64: Handle CPU isolation on last resort fallback rq selection
arm64: Exclude nohz_full CPUs from 32bits el0 support
lib: test_objpool: Use kthread_run_on_cpu()
kallsyms: Use kthread_run_on_cpu()
soc/qman: test: Use kthread_run_on_cpu()
arm/bL_switcher: Use kthread_run_on_cpu()
|
