| Age | Commit message (Collapse) | Author |
|---|
|
During XHCI resume, if there was a host controller error detected the
routine will attempt to re-initialize the XHCI HC, so that it can return
back to an operational state. If the XHCI host controller is being
removed, this sequence would be already handled within the XHCI halt path,
leading to a duplicate set of reg ops/calls. In addition, since the XHCI
bus is being removed, the overhead added in restarting the HCD is
unnecessary. Check for the XHC state before setting the reinit_xhc
parameter, which is responsible for triggering the restart.
Signed-off-by: Wesley Cheng <quic_wcheng@quicinc.com>
Message-ID: <20230531222719.14143-2-quic_wcheng@quicinc.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Add U1/U2 feature support of xHCI for ZHAOXIN.
Since both INTEL and ZHAOXIN need to check the tier where the device is
located to determine whether to enabled U1/U2, remove the previous INTEL
U1/U2 tier policy and add common policy in xhci_check_tier_policy.
If vendor has specific U1/U2 enable policy,quirks can be add to declare.
Suggested-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Weitao Wang <WeitaoWang-oc@zhaoxin.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Message-ID: <20230602144009.1225632-12-mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Not all platforms drivers need to set up custom quirks during the xhci
generic setup. Allow them to pass NULL as the function pointer when
calling xhci_gen_setup()
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Message-ID: <20230602144009.1225632-4-mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Check for the cold attach (CAS) bit while checking for other usb3
roothub port changes during host resume.
The CAS bit is set if a USB 3 device is connected while the host is
suspended in such a way it can't perform proper link training and
progress the link to the enabled U0 state.
If the CAS bit set we want to resume the root hub, and reset and
enumerate the newly connected device.
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Message-ID: <20230602144009.1225632-3-mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Avoid extra 120ms delay during system resume.
The xHC controller may signal wake up to 120ms before showing which usb
device caused the wake on the xHC port registers.
The xhci driver therefore checks for port activity up to 120ms during
resume, making sure that the hub driver can see the port change, and
won't immediately runtime suspend back due to no port activity.
This is however only needed for runtime resume as system resume will
resume all child hubs and other child usb devices anyway.
Fixes: 253f588c70f6 ("xhci: Improve detection of device initiated wake signal.")
Signed-off-by: Basavaraj Natikar <Basavaraj.Natikar@amd.com>
Acked-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20230428140056.1318981-3-Basavaraj.Natikar@amd.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Currently, the pci_resume method has only a flag indicating whether the
system is resuming from hibernation. In order to handle all PM events like
AUTO_RESUME (runtime resume from device in D3), RESUME (system resume from
s2idle, S3 or S4 states) etc change the pci_resume method to handle all PM
events.
Signed-off-by: Basavaraj Natikar <Basavaraj.Natikar@amd.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Acked-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20230428140056.1318981-2-Basavaraj.Natikar@amd.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
We need the USB fixes in here for testing, and this resolves two merge
conflicts, one pointed out by linux-next:
drivers/usb/dwc3/dwc3-pci.c
drivers/usb/host/xhci-pci.c
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
The command allocated to set exit latency LPM values need to be freed in
case the command is never queued. This would be the case if there is no
change in exit latency values, or device is missing.
Reported-by: Mirsad Goran Todorovac <mirsad.todorovac@alu.unizg.hr>
Link: https://lore.kernel.org/linux-usb/24263902-c9b3-ce29-237b-1c3d6918f4fe@alu.unizg.hr
Tested-by: Mirsad Goran Todorovac <mirsad.todorovac@alu.unizg.hr>
Fixes: 5c2a380a5aa8 ("xhci: Allocate separate command structures for each LPM command")
Cc: <Stable@vger.kernel.org>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20230330143056.1390020-4-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Previously the quirk was skipped when no iommu was present. The same
rationale for skipping the quirk also applies in the iommu.passthrough=1
case.
Skip applying the XHCI_ZERO_64B_REGS quirk if the device's iommu domain is
passthrough.
Fixes: 12de0a35c996 ("xhci: Add quirk to zero 64bit registers on Renesas PCIe controllers")
Cc: stable <stable@kernel.org>
Signed-off-by: D Scott Phillips <scott@os.amperecomputing.com>
Acked-by: Marc Zyngier <maz@kernel.org>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20230330143056.1390020-2-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Move function to sync MSI from xhci.c to xhci-pci.c to decouple PCI
specific code from generic xhci code.
No functional changes, function is an exact copy
[commit message rewording -Mathias]
Signed-off-by: Josue David Hernandez Gutierrez <josue.d.hernandez.gutierrez@intel.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20230317154715.535523-15-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Call function to sync MSI interrupts from pci specific xhci_pci_suspend()
function in xhci-pci.c instead of from generic xhci_suspend()
[commit message rewording -Mathias]
Signed-off-by: Josue David Hernandez Gutierrez <josue.d.hernandez.gutierrez@intel.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20230317154715.535523-14-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Move function to cleanup MSI from xhci.c to xhci-pci.c
This is to decouple PCI specific code from generic xhci code.
No functional changes, function is an exact copy
Signed-off-by: Josue David Hernandez Gutierrez <josue.d.hernandez.gutierrez@intel.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20230317154715.535523-13-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Call the PCI specific MSI/MSIX interrupt freeing code from the xhci-pci
callbacks instead of generic xhci code, decoupling PCI parts from
generic xhci functions.
Adds xhci_pci_stop() that overrides xhci_stop() for PCI xHC controllers.
This will free MSIX interrupts a bit later in the hc_driver stop
callback, but is still earlier than usb core frees "legacy" interrupts,
or interrupts for other hosts.
Signed-off-by: Josue David Hernandez Gutierrez <josue.d.hernandez.gutierrez@intel.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20230317154715.535523-12-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Move functions to setup msi from xhci.c to xhci-pci.c to decouple
PCI specific code from generic xhci code.
No functional changes, functions are an exact copy
[commit message rewording -Mathias]
Signed-off-by: Josue David Hernandez Gutierrez <josue.d.hernandez.gutierrez@intel.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20230317154715.535523-11-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
xhci MSI setup is currently done at the same time as xHC host is started
in xhci_run(). This couples the generic xhci code with PCI, and will
reconfigure MSI/MSIX interrupts every time xHC is started.
Decouple MSI/MSIX configuration from generic xhci code by moving MSI/MSIX
part to a PCI specific xhci_pci_run() function overriding xhci_run().
This allows us to remove unnecessay MSI/MSIX reconfiguration done every
time PCI xhci resumes from suspend. i.e. remove the xhci_cleanup_msix()
call from xhci_resume() and the xhci_try_enale_msi() call in xhci_run()
called a bit later by xhci_resume()
[minor changes and commit message rewrite -Mathias]
Signed-off-by: Josue David Hernandez Gutierrez <josue.d.hernandez.gutierrez@intel.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20230317154715.535523-10-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Simple helpers to set and clear the IE (interrupter enable) bit
for an interrupter.
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20230202150505.618915-5-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
xHC supports several interrupters, each with its own mmio register set,
event ring and MSI/MSI-X vector. Transfers can be assigned different
interrupters when queued. See xhci 4.17 for details.
Current driver only supports one interrupter.
Create a xhci_interrupter structure containing an event ring, pointer to
mmio registers for this interrupter, variables to store registers over s3
suspend, erst, etc. Add functions to create and free an interrupter, and
pass an interrupter pointer to functions that deal with events.
Secondary interrupters are also useful without having an interrupt vector.
One use case is the xHCI audio sideband offloading where a DSP can take
care of specific audio endpoints.
When all transfer events of an offloaded endpoint can be mapped to a
separate interrupter event ring the DSP can poll this ring, and we can mask
these events preventing waking up the CPU.
Only minor functional changes such as clearing some of the interrupter
registers when freeing the interrupter.
Still create only one primary interrupter.
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20230202150505.618915-4-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
We need the USB fixes in here and this resolves merge conflicts as
reported in linux-next in the following files:
drivers/usb/host/xhci.c
drivers/usb/host/xhci.h
drivers/usb/typec/ucsi/ucsi.c
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Add a hub_control() callback to the xhci_driver_overrides structure to
allow host drivers to override the default hub_control function. This
is required for Tegra which requires device specific actions for power
management to be executed during USB state transitions.
Signed-off-by: Jim Lin <jilin@nvidia.com>
Reviewed-by: Jon Hunter <jonathanh@nvidia.com>
Tested-by: Jon Hunter <jonathanh@nvidia.com>
Acked-by: Thierry Reding <treding@nvidia.com>
Acked-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20221111101813.32482-2-jilin@nvidia.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
One USB3 roothub port may support link power management, while another
root port on the same xHC can't due to different retimers used for
the ports.
This is the case with Intel Alder Lake, and possible future platforms
where retimers used for USB4 ports cause too long exit latecy to
enable native USB3 lpm U1 and U2 states.
Add a flag in the xhci port structure to indicate if the port is
lpm_incapable, and check it while calculating exit latency.
Cc: stable@vger.kernel.org
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20230116142216.1141605-6-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Allow PCI hosts to check and tune roothub and port settings
before the hub is up and running.
This override is needed to turn off U1 and U2 LPM for some ports
based on per port ACPI _DSM, _UPC, or possibly vendor specific mmio
values for Intel xHC hosts.
Usb core calls the host update_hub_device once it creates a hub.
Entering U1 or U2 link power save state on ports with this limitation
will cause link to fail, turning the usb device unusable in that setup.
Cc: stable@vger.kernel.org
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20230116142216.1141605-5-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Make sure xhci_free_dev() and xhci_kill_endpoint_urbs() do not race
and cause null pointer dereference when host suddenly dies.
Usb core may call xhci_free_dev() which frees the xhci->devs[slot_id]
virt device at the same time that xhci_kill_endpoint_urbs() tries to
loop through all the device's endpoints, checking if there are any
cancelled urbs left to give back.
hold the xhci spinlock while freeing the virt device
Cc: stable@vger.kernel.org
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20230116142216.1141605-4-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Systems based on Alder Lake P see significant boot time delay if
boot firmware tries to control usb ports in unexpected link states.
This is seen with self-powered usb devices that survive in U3 link
suspended state over S5.
A more generic solution to power off ports at shutdown was attempted in
commit 83810f84ecf1 ("xhci: turn off port power in shutdown")
but it caused regression.
Add host specific XHCI_RESET_TO_DEFAULT quirk which will reset host and
ports back to default state in shutdown.
Cc: stable@vger.kernel.org
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20221024142720.4122053-3-mathias.nyman@intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Show the completion code of a unsuccessful "enable slot" command.
Add it in a human readable form to the existing error message.
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20220921123450.671459-5-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 8b328f8002bc ("xhci: re-initialize the HC during resume if HCE was
set") introduced a new warning message when the host controller error
was set and re-initializing.
This is expected behavior on some designs which already set
`xhci->broken_suspend` so the new warning is alarming to some users.
Modify the code to only show the warning if this was a surprising behavior
to the XHCI driver.
Link: https://bugzilla.kernel.org/show_bug.cgi?id=216470
Fixes: 8b328f8002bc ("xhci: re-initialize the HC during resume if HCE was set")
Reported-by: Artem S. Tashkinov <aros@gmx.com>
Signed-off-by: Mario Limonciello <mario.limonciello@amd.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20220921123450.671459-4-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
This is only called in the xhci.c file, so make the symbol static.
Cc: Mathias Nyman <mathias.nyman@intel.com>
Link: https://lore.kernel.org/r/20220901134744.2039891-1-gregkh@linuxfoundation.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
This reverts commit 83810f84ecf11dfc5a9414a8b762c3501b328185.
Turning off port power in shutdown did cause issues such as a laptop not
proprly powering off, and some specific usb devies failing to enumerate the
subsequent boot after a warm reset.
So revert this.
Fixes: 83810f84ecf1 ("xhci: turn off port power in shutdown")
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20220825150840.132216-4-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
After xHC controller is started, either in probe or resume, it can take
a while before any of the connected usb devices are visible to the roothub
due to link training.
It's possible xhci driver loads, sees no acivity and suspends the host
before the USB device is visible.
In one testcase with a hotplugged xHC controller the host finally detected
the connected USB device and generated a wake 500ms after host initial
start.
If hosts didn't suspend the device duringe training it probablty wouldn't
take up to 500ms to detect it, but looking at specs reveal USB3 link
training has a couple long timeout values, such as 120ms
RxDetectQuietTimeout, and 360ms PollingLFPSTimeout.
So Add a 500ms grace period that keeps polling the roothub for 500ms after
start, preventing runtime suspend until USB devices are detected.
Cc: stable@vger.kernel.org
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20220825150840.132216-3-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
If ports are not turned off in shutdown then runtime suspended
self-powered USB devices may survive in U3 link state over S5.
During subsequent boot, if firmware sends an IPC command to program
the port in DISCONNECT state, it will time out, causing significant
delay in the boot time.
Turning off roothub port power is also recommended in xhci
specification 4.19.4 "Port Power" in the additional note.
Cc: stable@vger.kernel.org
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20220623111945.1557702-3-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
irq is disabled in xhci_quiesce(called by xhci_halt, with bit:2 cleared
in USBCMD register), but xhci_run(called by usb_add_hcd) re-enable it.
It's possible that you will receive thousands of interrupt requests
after initialization for 2.0 roothub. And you will get a lot of
warning like, "xHCI dying, ignoring interrupt. Shouldn't IRQs be
disabled?". This amount of interrupt requests will cause the entire
system to freeze.
This problem was first found on a device with ASM2142 host controller
on it.
[tidy up old code while moving it, reword header -Mathias]
Cc: stable@kernel.org
Signed-off-by: Hongyu Xie <xiehongyu1@kylinos.cn>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20220623111945.1557702-2-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
In the re-init path xhci_resume() passes 'hcd->primary_hcd' to hci_init(),
however this field isn't initialized by __usb_create_hcd() for a HCD
without secondary controller.
xhci_resume() is called once per xHC device, not per hcd, so the extra
checking for primary hcd can be removed.
Fixes: e0fe986972f5 ("usb: host: xhci-plat: prepare operation w/o shared hcd")
Reported-by: Matthias Kaehlcke <mka@chromium.org>
Tested-by: Matthias Kaehlcke <mka@chromium.org>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20220610115338.863152-2-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
The support for xHCI controllers with only one roothub, and the code
to defer primary roothub registation until second roothub got merged
to usb-next for 5.19 at the same time.
commit 873f323618c2 ("xhci: prepare for operation w/o shared hcd")
commit b7a4f9b5d0e4 ("xhci: Set HCD flag to defer primary roothub
registration")
These got merged in such a way that the flag to defer primary roothub
registration is set even for xHC controllers with just one roothub.
Fix this by setting the defer flag in a codepath taken only if we have
two roothubs
Fixes: 873f323618c2 ("xhci: prepare for operation w/o shared hcd")
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20220516094850.19788-2-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Don't enable U1 or U2 Link powermanagenet (LPM) states for USB3
devices connected to tier 2 or further hubs.
For unknown reasons we previously only prevented U1.
Be consistent, and prevent both U1/U2 states if tier policy doesn't
allow LPM.
Also check the tier policy a bit earlier, and return if U1/U2 is
not allowed. This avoids unnecessary xhci MEL commands.
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20220511220450.85367-8-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
The 'stop endpoint' command timer was started when a 'stop endpoint'
command was added to the command queue.
This can trigger unwanted timeouts if there are several pending commands
in the queue that xHC needs to handle first.
The generic command timer, which was added later than the 'stop endpoint'
timeout timer, times each command currently being handled by xHC hardware.
A timed out stop endpoint command was treated as a more severe issue than
other failed commands, so the separate stop endpoint timer was left
unchanged.
Use the generic command timer for stop endpoint commands. Identify if
the timed out command was a stop endpoint command in the generic handler,
and treat it with the same severity as earlier.
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20220511220450.85367-7-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
This patch prepares xhci for the following scenario:
- If either of the root hubs has no ports, then omit shared hcd
- Main hcd can be USB3 if there are no USB2 ports
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20220511220450.85367-3-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Factoring out parts of xhci_gen_setup() has two motivations:
- When adding functionaliy to omit shared hcd if not needed in a
subsequent patch, we'll have to call xhci_hcd_init_usb3_data()
from two places.
- It reduces size of xhci_gen_setup() and makes it better readable.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20220511220450.85367-2-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Set "HCD_FLAG_DEFER_RH_REGISTER" to hcd->flags in xhci_run() to defer
registering primary roothub in usb_add_hcd() if xhci has two roothubs.
This will make sure both primary roothub and secondary roothub will be
registered along with the second HCD.
This is required for cold plugged USB devices to be detected in certain
PCIe USB cards (like Inateck USB card connected to AM64 EVM or J7200 EVM).
This patch has been added and reverted earier as it triggered a race
in usb device enumeration.
That race is now fixed in 5.16-rc3, and in stable back to 5.4
commit 6cca13de26ee ("usb: hub: Fix locking issues with address0_mutex")
commit 6ae6dc22d2d1 ("usb: hub: Fix usb enumeration issue due to address0
race")
[minor rebase change, and commit message update -Mathias]
CC: stable@vger.kernel.org # 5.4+
Suggested-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Tested-by: Chris Chiu <chris.chiu@canonical.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Link: https://lore.kernel.org/r/20220510091630.16564-3-kishon@ti.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
While rebooting, XHCI controller and its bus device will be shut down
in order by .shutdown callback. Stopping roothubs polling in
xhci_shutdown() can prevent XHCI driver from accessing port status
after its bus device shutdown.
Take PCIe XHCI controller as example, if XHCI driver doesn't stop roothubs
polling, XHCI driver may access PCIe BAR register for port status after
parent PCIe root port driver is shutdown and cause PCIe bus error.
[check shared hcd exist before stopping its roothub polling -Mathias]
Cc: stable@vger.kernel.org
Signed-off-by: Henry Lin <henryl@nvidia.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20220408134823.2527272-3-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
The ret/retval will be set when it used, no need to init at definition.
[modified subject line -Mathias]
Signed-off-by: Linyu Yuan <quic_linyyuan@quicinc.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20220303110903.1662404-10-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
It is more readable to add blank lines.
Signed-off-by: Linyu Yuan <quic_linyyuan@quicinc.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20220303110903.1662404-9-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
There is no need to store temperary value in hcc_params.
Signed-off-by: Linyu Yuan <quic_linyyuan@quicinc.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20220303110903.1662404-8-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
xhci_reset() timeout was increased from 250ms to 10 seconds in order to
give Renesas 720201 xHC enough time to get ready in probe.
xhci_reset() is called with interrupts disabled in other places, and
waiting for 10 seconds there is not acceptable.
Add a timeout parameter to xhci_reset(), and adjust it back to 250ms
when called from xhci_stop() or xhci_shutdown() where interrupts are
disabled, and successful reset isn't that critical.
This solves issues when deactivating host mode on platforms like SM8450.
For now don't change the timeout if xHC is reset in xhci_resume().
No issues are reported for it, and we need the reset to succeed.
Locking around that reset needs to be revisited later.
Additionally change the signed integer timeout parameter in
xhci_handshake() to a u64 to match the timeout value we pass to
readl_poll_timeout_atomic()
Fixes: 22ceac191211 ("xhci: Increase reset timeout for Renesas 720201 host.")
Cc: stable@vger.kernel.org
Reported-by: Sergey Shtylyov <s.shtylyov@omp.ru>
Reported-by: Pavan Kondeti <quic_pkondeti@quicinc.com>
Tested-by: Pavan Kondeti <quic_pkondeti@quicinc.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20220303110903.1662404-2-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
We need the USB fixes in here, and it resolves a merge conflict in:
drivers/usb/dwc3/dwc3-pci.c
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
In xhci_endpoint_{disable|reset}() the expression '&vdev->eps[ep_index]'
just cannot be NULL, so the checks have no sense at all...
Found by Linux Verification Center (linuxtesting.org) with the SVACE static
analysis tool.
Signed-off-by: Sergey Shtylyov <s.shtylyov@omp.ru>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20220216095153.1303105-9-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Every lpm commmand, both for USB 2 and USB 3 devies used the same
xhci->lpm_command structure to change max exit latency.
xhci->lpm_command is only protected by a hcd->bandwidth mutex, which is
not enoungh as USB 2 and USB 3 devices are behind separate HCDs.
Simplify code and avoid unnecessary locking risks by allocating
separate command structures for each lpm command, just like with
all other commands.
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20220216095153.1303105-7-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
The current workaround to call the dbc_tty_init() in probe is
not working in case we have several xhci devices with dbc enabled.
dbc_tty_init() should be called only once by a module init call when
module is loaded.
until dbgtty is its own module call dbc_tty_init() from xhci
module init call.
Same is true for unloading and dbc_tty_exit()
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20220216095153.1303105-5-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
These names give the impression the functions are related to
module init calls, but are in fact creating and removing the dbc
fake device
Rename them to xhci_create_dbc_dev() and xhci_remove_dbc_dev().
We will need the _init and _exit names for actual dbc module init
and exit calls.
No functional changes
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20220216095153.1303105-4-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
The -ENODEV return value from xhci_check_args() is incorrectly changed
to -EINVAL in a couple places before propagated further.
xhci_check_args() returns 4 types of value, -ENODEV, -EINVAL, 1 and 0.
xhci_urb_enqueue and xhci_check_streams_endpoint return -EINVAL if
the return value of xhci_check_args <= 0.
This causes problems for example r8152_submit_rx, calling usb_submit_urb
in drivers/net/usb/r8152.c.
r8152_submit_rx will never get -ENODEV after submiting an urb when xHC
is halted because xhci_urb_enqueue returns -EINVAL in the very beginning.
[commit message and header edit -Mathias]
Fixes: 203a86613fb3 ("xhci: Avoid NULL pointer deref when host dies.")
Cc: stable@vger.kernel.org
Signed-off-by: Hongyu Xie <xiehongyu1@kylinos.cn>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20220215123320.1253947-3-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
When HCE(Host Controller Error) is set, it means an internal
error condition has been detected. Software needs to re-initialize
the HC, so add this check in xhci resume.
Cc: stable@vger.kernel.org
Signed-off-by: Puma Hsu <pumahsu@google.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20220215123320.1253947-2-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Use max() in order to make code cleaner.
Reported-by: Zeal Robot <zealci@zte.com.cn>
Signed-off-by: Changcheng Deng <deng.changcheng@zte.com.cn>
Link: https://lore.kernel.org/r/20211215091602.445009-1-deng.changcheng@zte.com.cn
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
