| Age | Commit message (Collapse) | Author |
|---|
|
RZ/G2E USB 3.0 implementation is like the one found on R-Car E3,
therefore add the same quirk.
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
Reviewed-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Fabrizio Castro <fabrizio.castro@bp.renesas.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
|
|
This patch adds a safety connection way for "forced_b_device" with
"workaround_for_vbus" like below:
< Example for R-Car E3 Ebisu >
# modprobe <any usb gadget driver>
# echo 1 > /sys/kernel/debug/ee020000.usb/b_device
(connect a usb cable to host side.)
# echo 2 > /sys/kernel/debug/ee020000.usb/b_device
Previous code should have connected a usb cable before the "b_device"
is set to 1 on the Ebisu board. However, if xHCI driver on the board
is probed, it causes some troubles:
- Conflicts USB VBUS/signals between the board and another host.
- "Cannot enable. Maybe the USB cable is bad?" might happen on
both the board and another host with a usb hub.
- Cannot enumerate a usb gadget correctly because an interruption
of VBUS change happens unexpectedly.
Reported-by: Kazuya Mizuguchi <kazuya.mizuguchi.ks@renesas.com>
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
|
|
Since r8a77990 (R-Car E3) doesn't have VBUS detect pin and
number of ramif is 4, this patch adds a new renesas_usb3_priv
variable for the SoC.
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
|
|
If the "workaround_for_vbus" is true, the driver will not call
usb_disconnect(). So, since the controller keeps some registers'
value, the driver doesn't re-enumarate suitable speed after
the b-device mode is disabled. To fix the issue, this patch
adds usb_disconnect() calling in renesas_usb3_b_device_write()
if workaround_for_vbus is true.
Fixes: 43ba968b00ea ("usb: gadget: udc: renesas_usb3: add debugfs to set the b-device mode")
Cc: <stable@vger.kernel.org> # v4.14+
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
|
|
This patch fixes an issue that maxpacket size of ep0 is incorrect
for SuperSpeed. Otherwise, CDC NCM class with SuperSpeed doesn't
work correctly on this driver because its control read data size
is more than 64 bytes.
Reported-by: Junki Kato <junki.kato.xk@renesas.com>
Fixes: 746bfe63bba3 ("usb: gadget: renesas_usb3: add support for Renesas USB3.0 peripheral controller")
Cc: <stable@vger.kernel.org> # v4.5+
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Tested-by: Junki Kato <junki.kato.xk@renesas.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
|
|
This patch adds role switch support for R-Car SoCs into the USB 3.0
peripheral driver. Some R-Car SoCs (e.g. R-Car H3) have USB 3.0
dual-role device controller which has the USB 3.0 xHCI host and
Renesas USB 3.0 peripheral.
Unfortunately, the mode change register (DRD_CON) contains
the USB 3.0 peripheral controller side only. So, this renesas_usb3
driver manages the DRD_CON now. However, in peripheral mode, the host
should stop. Also the host hardware needs to reinitialize its own
registers when the mode changes from peripheral to host mode.
Otherwise, the host cannot work correctly (e.g. detect a device
as high-speed).
To achieve this reinitialization by a driver, this driver also
registers a role switch driver to manage the DRD_CON and get
a device pointer of usb 3.0 host from "companion" property of OF.
Then, when the usb role is changed, renesas_usb3_role_switch_set()
will attach/release the xhci-plat driver to reinitialize the host
hardware.
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
|
|
The devm_kzalloc() function has a 2-factor argument form, devm_kcalloc().
This patch replaces cases of:
devm_kzalloc(handle, a * b, gfp)
with:
devm_kcalloc(handle, a * b, gfp)
as well as handling cases of:
devm_kzalloc(handle, a * b * c, gfp)
with:
devm_kzalloc(handle, array3_size(a, b, c), gfp)
as it's slightly less ugly than:
devm_kcalloc(handle, array_size(a, b), c, gfp)
This does, however, attempt to ignore constant size factors like:
devm_kzalloc(handle, 4 * 1024, gfp)
though any constants defined via macros get caught up in the conversion.
Any factors with a sizeof() of "unsigned char", "char", and "u8" were
dropped, since they're redundant.
Some manual whitespace fixes were needed in this patch, as Coccinelle
really liked to write "=devm_kcalloc..." instead of "= devm_kcalloc...".
The Coccinelle script used for this was:
// Fix redundant parens around sizeof().
@@
expression HANDLE;
type TYPE;
expression THING, E;
@@
(
devm_kzalloc(HANDLE,
- (sizeof(TYPE)) * E
+ sizeof(TYPE) * E
, ...)
|
devm_kzalloc(HANDLE,
- (sizeof(THING)) * E
+ sizeof(THING) * E
, ...)
)
// Drop single-byte sizes and redundant parens.
@@
expression HANDLE;
expression COUNT;
typedef u8;
typedef __u8;
@@
(
devm_kzalloc(HANDLE,
- sizeof(u8) * (COUNT)
+ COUNT
, ...)
|
devm_kzalloc(HANDLE,
- sizeof(__u8) * (COUNT)
+ COUNT
, ...)
|
devm_kzalloc(HANDLE,
- sizeof(char) * (COUNT)
+ COUNT
, ...)
|
devm_kzalloc(HANDLE,
- sizeof(unsigned char) * (COUNT)
+ COUNT
, ...)
|
devm_kzalloc(HANDLE,
- sizeof(u8) * COUNT
+ COUNT
, ...)
|
devm_kzalloc(HANDLE,
- sizeof(__u8) * COUNT
+ COUNT
, ...)
|
devm_kzalloc(HANDLE,
- sizeof(char) * COUNT
+ COUNT
, ...)
|
devm_kzalloc(HANDLE,
- sizeof(unsigned char) * COUNT
+ COUNT
, ...)
)
// 2-factor product with sizeof(type/expression) and identifier or constant.
@@
expression HANDLE;
type TYPE;
expression THING;
identifier COUNT_ID;
constant COUNT_CONST;
@@
(
- devm_kzalloc
+ devm_kcalloc
(HANDLE,
- sizeof(TYPE) * (COUNT_ID)
+ COUNT_ID, sizeof(TYPE)
, ...)
|
- devm_kzalloc
+ devm_kcalloc
(HANDLE,
- sizeof(TYPE) * COUNT_ID
+ COUNT_ID, sizeof(TYPE)
, ...)
|
- devm_kzalloc
+ devm_kcalloc
(HANDLE,
- sizeof(TYPE) * (COUNT_CONST)
+ COUNT_CONST, sizeof(TYPE)
, ...)
|
- devm_kzalloc
+ devm_kcalloc
(HANDLE,
- sizeof(TYPE) * COUNT_CONST
+ COUNT_CONST, sizeof(TYPE)
, ...)
|
- devm_kzalloc
+ devm_kcalloc
(HANDLE,
- sizeof(THING) * (COUNT_ID)
+ COUNT_ID, sizeof(THING)
, ...)
|
- devm_kzalloc
+ devm_kcalloc
(HANDLE,
- sizeof(THING) * COUNT_ID
+ COUNT_ID, sizeof(THING)
, ...)
|
- devm_kzalloc
+ devm_kcalloc
(HANDLE,
- sizeof(THING) * (COUNT_CONST)
+ COUNT_CONST, sizeof(THING)
, ...)
|
- devm_kzalloc
+ devm_kcalloc
(HANDLE,
- sizeof(THING) * COUNT_CONST
+ COUNT_CONST, sizeof(THING)
, ...)
)
// 2-factor product, only identifiers.
@@
expression HANDLE;
identifier SIZE, COUNT;
@@
- devm_kzalloc
+ devm_kcalloc
(HANDLE,
- SIZE * COUNT
+ COUNT, SIZE
, ...)
// 3-factor product with 1 sizeof(type) or sizeof(expression), with
// redundant parens removed.
@@
expression HANDLE;
expression THING;
identifier STRIDE, COUNT;
type TYPE;
@@
(
devm_kzalloc(HANDLE,
- sizeof(TYPE) * (COUNT) * (STRIDE)
+ array3_size(COUNT, STRIDE, sizeof(TYPE))
, ...)
|
devm_kzalloc(HANDLE,
- sizeof(TYPE) * (COUNT) * STRIDE
+ array3_size(COUNT, STRIDE, sizeof(TYPE))
, ...)
|
devm_kzalloc(HANDLE,
- sizeof(TYPE) * COUNT * (STRIDE)
+ array3_size(COUNT, STRIDE, sizeof(TYPE))
, ...)
|
devm_kzalloc(HANDLE,
- sizeof(TYPE) * COUNT * STRIDE
+ array3_size(COUNT, STRIDE, sizeof(TYPE))
, ...)
|
devm_kzalloc(HANDLE,
- sizeof(THING) * (COUNT) * (STRIDE)
+ array3_size(COUNT, STRIDE, sizeof(THING))
, ...)
|
devm_kzalloc(HANDLE,
- sizeof(THING) * (COUNT) * STRIDE
+ array3_size(COUNT, STRIDE, sizeof(THING))
, ...)
|
devm_kzalloc(HANDLE,
- sizeof(THING) * COUNT * (STRIDE)
+ array3_size(COUNT, STRIDE, sizeof(THING))
, ...)
|
devm_kzalloc(HANDLE,
- sizeof(THING) * COUNT * STRIDE
+ array3_size(COUNT, STRIDE, sizeof(THING))
, ...)
)
// 3-factor product with 2 sizeof(variable), with redundant parens removed.
@@
expression HANDLE;
expression THING1, THING2;
identifier COUNT;
type TYPE1, TYPE2;
@@
(
devm_kzalloc(HANDLE,
- sizeof(TYPE1) * sizeof(TYPE2) * COUNT
+ array3_size(COUNT, sizeof(TYPE1), sizeof(TYPE2))
, ...)
|
devm_kzalloc(HANDLE,
- sizeof(TYPE1) * sizeof(THING2) * (COUNT)
+ array3_size(COUNT, sizeof(TYPE1), sizeof(TYPE2))
, ...)
|
devm_kzalloc(HANDLE,
- sizeof(THING1) * sizeof(THING2) * COUNT
+ array3_size(COUNT, sizeof(THING1), sizeof(THING2))
, ...)
|
devm_kzalloc(HANDLE,
- sizeof(THING1) * sizeof(THING2) * (COUNT)
+ array3_size(COUNT, sizeof(THING1), sizeof(THING2))
, ...)
|
devm_kzalloc(HANDLE,
- sizeof(TYPE1) * sizeof(THING2) * COUNT
+ array3_size(COUNT, sizeof(TYPE1), sizeof(THING2))
, ...)
|
devm_kzalloc(HANDLE,
- sizeof(TYPE1) * sizeof(THING2) * (COUNT)
+ array3_size(COUNT, sizeof(TYPE1), sizeof(THING2))
, ...)
)
// 3-factor product, only identifiers, with redundant parens removed.
@@
expression HANDLE;
identifier STRIDE, SIZE, COUNT;
@@
(
devm_kzalloc(HANDLE,
- (COUNT) * STRIDE * SIZE
+ array3_size(COUNT, STRIDE, SIZE)
, ...)
|
devm_kzalloc(HANDLE,
- COUNT * (STRIDE) * SIZE
+ array3_size(COUNT, STRIDE, SIZE)
, ...)
|
devm_kzalloc(HANDLE,
- COUNT * STRIDE * (SIZE)
+ array3_size(COUNT, STRIDE, SIZE)
, ...)
|
devm_kzalloc(HANDLE,
- (COUNT) * (STRIDE) * SIZE
+ array3_size(COUNT, STRIDE, SIZE)
, ...)
|
devm_kzalloc(HANDLE,
- COUNT * (STRIDE) * (SIZE)
+ array3_size(COUNT, STRIDE, SIZE)
, ...)
|
devm_kzalloc(HANDLE,
- (COUNT) * STRIDE * (SIZE)
+ array3_size(COUNT, STRIDE, SIZE)
, ...)
|
devm_kzalloc(HANDLE,
- (COUNT) * (STRIDE) * (SIZE)
+ array3_size(COUNT, STRIDE, SIZE)
, ...)
|
devm_kzalloc(HANDLE,
- COUNT * STRIDE * SIZE
+ array3_size(COUNT, STRIDE, SIZE)
, ...)
)
// Any remaining multi-factor products, first at least 3-factor products,
// when they're not all constants...
@@
expression HANDLE;
expression E1, E2, E3;
constant C1, C2, C3;
@@
(
devm_kzalloc(HANDLE, C1 * C2 * C3, ...)
|
devm_kzalloc(HANDLE,
- (E1) * E2 * E3
+ array3_size(E1, E2, E3)
, ...)
|
devm_kzalloc(HANDLE,
- (E1) * (E2) * E3
+ array3_size(E1, E2, E3)
, ...)
|
devm_kzalloc(HANDLE,
- (E1) * (E2) * (E3)
+ array3_size(E1, E2, E3)
, ...)
|
devm_kzalloc(HANDLE,
- E1 * E2 * E3
+ array3_size(E1, E2, E3)
, ...)
)
// And then all remaining 2 factors products when they're not all constants,
// keeping sizeof() as the second factor argument.
@@
expression HANDLE;
expression THING, E1, E2;
type TYPE;
constant C1, C2, C3;
@@
(
devm_kzalloc(HANDLE, sizeof(THING) * C2, ...)
|
devm_kzalloc(HANDLE, sizeof(TYPE) * C2, ...)
|
devm_kzalloc(HANDLE, C1 * C2 * C3, ...)
|
devm_kzalloc(HANDLE, C1 * C2, ...)
|
- devm_kzalloc
+ devm_kcalloc
(HANDLE,
- sizeof(TYPE) * (E2)
+ E2, sizeof(TYPE)
, ...)
|
- devm_kzalloc
+ devm_kcalloc
(HANDLE,
- sizeof(TYPE) * E2
+ E2, sizeof(TYPE)
, ...)
|
- devm_kzalloc
+ devm_kcalloc
(HANDLE,
- sizeof(THING) * (E2)
+ E2, sizeof(THING)
, ...)
|
- devm_kzalloc
+ devm_kcalloc
(HANDLE,
- sizeof(THING) * E2
+ E2, sizeof(THING)
, ...)
|
- devm_kzalloc
+ devm_kcalloc
(HANDLE,
- (E1) * E2
+ E1, E2
, ...)
|
- devm_kzalloc
+ devm_kcalloc
(HANDLE,
- (E1) * (E2)
+ E1, E2
, ...)
|
- devm_kzalloc
+ devm_kcalloc
(HANDLE,
- E1 * E2
+ E1, E2
, ...)
)
Signed-off-by: Kees Cook <keescook@chromium.org>
|
|
debugfs_create functions
When calling debugfs functions, there is no need to ever check the
return value. The function can work or not, but the code logic should
never do something different based on this.
Cc: Felipe Balbi <balbi@kernel.org>
Cc: Simon Horman <horms+renesas@verge.net.au>
Cc: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
This patch fixes an issue that this driver cause double phy_put()
calling. This driver must not call phy_put() in the remove because
the driver calls devm_phy_get() in the probe.
Fixes: 279d4bc64060 ("usb: gadget: udc: renesas_usb3: add support for generic phy")
Cc: <stable@vger.kernel.org> # v4.15+
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
|
|
This patch fixes an issue that reconnection is possible to fail
because unexpected state handling happens by the irqs. To fix the issue,
the driver disables the controller's irqs when disconnected.
Fixes: 746bfe63bba3 ("usb: gadget: renesas_usb3: add support for Renesas USB3.0 peripheral controller")
Cc: <stable@vger.kernel.org> # v4.5+
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
|
|
This patch fixes an issue that this driver ignores errors other than
the non-existence of the device, f.e. a memory allocation failure
in devm_phy_get(). So, this patch replaces devm_phy_get() with
devm_phy_optional_get().
Reported-by: Simon Horman <horms+renesas@verge.net.au>
Fixes: 279d4bc64060 ("usb: gadget: udc: renesas_usb3: add support for generic phy")
Cc: <stable@vger.kernel.org> # v4.15+
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
|
|
This patch fixes an issue that this driver cannot call phy_init()
if a gadget driver is alreadly loaded because usb_add_gadget_udc()
might call renesas_usb3_start() via .udc_start.
This patch also revises the typo (s/an optional/optional/).
Fixes: 279d4bc64060 ("usb: gadget: udc: renesas_usb3: add support for generic phy")
Cc: <stable@vger.kernel.org> # v4.15+
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
|
|
This patch fixes an issue that this driver causes panic if a gadget
driver is already loaded because usb_add_gadget_udc() might call
renesas_usb3_start() via .udc_start, and then pm_runtime_get_sync()
in renesas_usb3_start() doesn't work correctly.
Note that the usb3_to_dev() macro should not be called at this timing
because the macro uses the gadget structure.
Fixes: cf06df3fae28 ("usb: gadget: udc: renesas_usb3: move pm_runtime_{en,dis}able()")
Cc: <stable@vger.kernel.org> # v4.15+
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
|
|
This patch fixes an issue that this driver doesn't remove its debugfs.
Fixes: 43ba968b00ea ("usb: gadget: udc: renesas_usb3: add debugfs to set the b-device mode")
Cc: <stable@vger.kernel.org> # v4.14+
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
|
|
This patch fixes an issue that the renesas_usb3_remove() causes
NULL pointer dereference because the usb3_to_dev() macro will use
the gadget instance and it will be deleted before.
Fixes: cf06df3fae28 ("usb: gadget: udc: renesas_usb3: move pm_runtime_{en,dis}able()")
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
|
|
This controller on R-Car Gen3 has 6 pipes that included PIPE 0 for
control actually. But, the datasheet has error in writing as it has
31 pipes. (However, the previous code defined 30 pipes wrongly...)
Anyway, this patch fixes it.
Fixes: 746bfe63bba3 ("usb: gadget: renesas_usb3: add support for Renesas USB3.0 peripheral controller")
Cc: <stable@vger.kernel.org> # v4.5+
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
|
|
Now that the SPDX tag is in all USB files, that identifies the license
in a specific and legally-defined manner. So the extra GPL text wording
can be removed as it is no longer needed at all.
This is done on a quest to remove the 700+ different ways that files in
the kernel describe the GPL license text. And there's unneeded stuff
like the address (sometimes incorrect) for the FSF which is never
needed.
No copyright headers or other non-license-description text was removed.
Cc: Kevin Cernekee <cernekee@gmail.com>
Cc: Florian Fainelli <f.fainelli@gmail.com>
Cc: Vladimir Zapolskiy <vz@mleia.com>
Cc: Sylvain Lemieux <slemieux.tyco@gmail.com>
Cc: Daniel Mack <daniel@zonque.org>
Cc: Haojian Zhuang <haojian.zhuang@gmail.com>
Cc: Michal Simek <michal.simek@xilinx.com>
Cc: "Sören Brinkmann" <soren.brinkmann@xilinx.com>
Cc: Raviteja Garimella <raviteja.garimella@broadcom.com>
Cc: Romain Perier <romain.perier@collabora.com>
Cc: Johan Hovold <johan@kernel.org>
Cc: Al Cooper <alcooperx@gmail.com>
Cc: Srinath Mannam <srinath.mannam@broadcom.com>
Cc: Roger Quadros <rogerq@ti.com>
Cc: Krzysztof Opasiak <k.opasiak@samsung.com>
Cc: Stefan Agner <stefan@agner.ch>
Cc: Alan Stern <stern@rowland.harvard.edu>
Cc: "Felix Hädicke" <felixhaedicke@web.de>
Cc: Peter Chen <peter.chen@nxp.com>
Cc: Allen Pais <allen.lkml@gmail.com>
Cc: Yuyang Du <yuyang.du@intel.com>
Acked-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Acked-by: Nicolas Ferre <nicolas.ferre@microchip.com>
Acked-by: Robert Jarzmik <robert.jarzmik@free.fr>
Acked-by: Li Yang <leoyang.li@nxp.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
It's good to have SPDX identifiers in all files to make it easier to
audit the kernel tree for correct licenses.
Update the drivers/usb/ and include/linux/usb* files with the correct
SPDX license identifier based on the license text in the file itself.
The SPDX identifier is a legally binding shorthand, which can be used
instead of the full boiler plate text.
This work is based on a script and data from Thomas Gleixner, Philippe
Ombredanne, and Kate Stewart.
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Kate Stewart <kstewart@linuxfoundation.org>
Cc: Philippe Ombredanne <pombredanne@nexb.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Acked-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Acked-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Don't populate the const array max_packet_array on the stack, instead make
it static. Makes the object code smaller by over 90 bytes:
Before:
text data bss dec hex filename
34337 5612 128 40077 9c8d renesas_usb3.o
After:
text data bss dec hex filename
34149 5708 128 39985 9c31 renesas_usb3.o
(gcc version 7.2.0 x86_64)
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/chanwoo/extcon into usb-next
Chanwoo writes:
Update extcon for 4.15
Detailed description for this pull request:
1. Split out extcon header file for consumer and provider device
: The extcon has two type of extcon devices as following.
- 'extcon provider deivce' adds new extcon device and detect
the state/properties of external connector. Also, it notifies the
state/properties to the extcon consumer device.
- 'extcon consumer device' gets the change state/properties
from extcon provider device.
Prior to that, include/linux/extcon.h contains all exported API
for both provider and consumer device driver. To clarify the meaning
of header file and to remove the wrong use-case on consumer device.
- include/linux/extcon-provider.h includes API for the provider device driver.
- include/linux/extcon.h includes the API for the consumer device driver.
2. Support the SmartDock accessory on extcon-max77843.c device driver
- Support the SmartDock accessory which detects following connectors
at the same time.
: USB host throught USB hub for mouse, keyboard and so on.
: MHL connector for video output.
: Charger connector for battery charging.
- It tested with Unitek Y-2165 MHL+OTG Hub Smart Phone Dock.
3. Fix the minor issue of extcon driver
- Delete the unneeded initialization in extcon-max14577.
- Make extcon_info static const in order to fix the warning.
|
|
The extcon has two type of extcon devices as following.
- 'extcon provider deivce' adds new extcon device and detect the
state/properties of external connector. Also, it notifies the
state/properties to the extcon consumer device.
- 'extcon consumer device' gets the change state/properties
from extcon provider device.
Prior to that, include/linux/extcon.h contains all exported API for
both provider and consumer device driver. To clarify the meaning of
header file and to remove the wrong use-case on consumer device,
this patch separates into extcon.h and extcon-provider.h.
[Description for include/linux/{extcon.h|extcon-provider.h}]
- extcon.h includes the extcon API and data structure for extcon consumer
device driver. This header file contains the following APIs:
: Register/unregister the notifier to catch the change of extcon device
: Get the extcon device instance
: Get the extcon device name
: Get the state of each external connector
: Get the property value of each external connector
: Get the property capability of each external connector
- extcon-provider.h includes the extcon API and data structure for extcon
provider device driver. This header file contains the following APIs:
: Include 'include/linux/extcon.h'
: Allocate the memory for extcon device instance
: Register/unregister extcon device
: Set the state of each external connector
: Set the property value of each external connector
: Set the property capability of each external connector
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
Acked-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
Acked-by: Chen-Yu Tsai <wens@csie.org>
Acked-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Acked-by: Lee Jones <lee.jones@linaro.org>
Acked-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Acked-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Acked-by: Kishon Vijay Abraham I <kishon@ti.com>
|
|
Use the of_device_get_match_data() helper instead of open coding,
postponing the matching until when it's really needed.
Note that the renesas_usb3 driver is used with DT only, so there's
always a valid match.
Reviewed-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
|
|
This patch adds support for generic phy as an optional. If you want
to use a generic phy (e.g. phy-rcar-gen3-usb3 driver) on this driver,
you have to do "insmod phy-rcar-gen3-usb3.ko" first for now.
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
|
|
This patch adds support suspend/resume functions
Signed-off-by: Kazuya Mizuguchi <kazuya.mizuguchi.ks@renesas.com>
[shimoda: add the commit log]
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
|
|
This patch moves pm_runtime_{en,dis}able() call timing to
renesas_usb3_{probe,remove}() for supporting PM_SLEEP feature in
the future.
Signed-off-by: Kazuya Mizuguchi <kazuya.mizuguchi.ks@renesas.com>
[shimoda: Revise the commit log]
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
|
|
This patch fixes an issue that this driver cannot go status stage
in control read when the req.zero is set to 1 and the len in
usb3_write_pipe() is set to 0. Otherwise, if we use g_ncm driver,
usb enumeration takes long time (5 seconds or more).
Fixes: 746bfe63bba3 ("usb: gadget: renesas_usb3: add support for Renesas USB3.0 peripheral controller")
Cc: <stable@vger.kernel.org> # v4.5+
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
|
|
According to the datasheet of R-Car Gen3, the Pn_RAMMAP.Pn_MPKT should
be set to one of 8, 16, 32, 64, 512 and 1024. Otherwise, when a gadget
driver uses an interrupt endpoint, unexpected behavior happens. So,
this patch fixes it.
Fixes: 746bfe63bba3 ("usb: gadget: renesas_usb3: add support for Renesas USB3.0 peripheral controller")
Cc: <stable@vger.kernel.org> # v4.5+
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
|
|
When bRequestType & USB_DIR_IN is false and req.length is 0 in control
transfer, since it means non-data, this driver should not set the mode
as control write. So, this patch fixes it.
Fixes: 746bfe63bba3 ("usb: gadget: renesas_usb3: add support for Renesas USB3.0 peripheral controller")
Cc: <stable@vger.kernel.org> # v4.5+
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/balbi/usb into usb-next
Felipe writes:
usb: changes for v4.14 merge window
Not a big pull request this time around. Only 49 non-merge
commits. This pull request is, however, all over the place. Most of
the changes are in the bdc driver adding support for USB Phy layer and
PM.
Renesas adds support for R-Car H3 ES2.0 and R-Car M3-W SoCs.
Also here is PM_RUNTIME support for dwc3-keystone.
UDC Core got a DMA unmap fix to make sure we only unmap requests that
were, indeed, mapped.
Other than these, we have a lot of cleanups, many of them adding
'const' to several places.
|
|
Make the structure const as it is only stored in the ops field of a
usb_ep structure, which is of type const.
Done using Coccinelle.
Signed-off-by: Bhumika Goyal <bhumirks@gmail.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
|
|
This patch adds support for R-Car M3-W. This patch also adds R-Car
Gen3 generic version's compatible and changes ".compatible" in
the usb3_of_match from "renesas,r8a7796-usb3-peri" to
"renesas,rcar-gen3-usb3-peri".
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
|
|
This patch adds support for R-Car H3 ES2.0. Since this SoC revision
doesn't need workaround for vbus detection and number of ramif is
increased. So, this driver uses soc_device_match() to detect it.
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
|
|
This patch adds debugfs to set the "b-device" mode for using a board
which is not connected to the ID pin (e.g. CN11 on Salvator-X).
If we want to use peripheral mode on such a board, we have to disable
VBUS output first. So, this patch can set such a mode as the following:
# mount -t debugfs none /sys/kernel/debug
# modprobe renesas_usb3
# modprobe g_mass_storage file=/dev/shm/test.bin
# echo 1 > /sys/kernel/debug/ee020000.usb/b_device
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
|
|
platform_get_irq() returns an error code, but the renesas_usb3 driver
ignores it and always returns -ENODEV. This is not correct and,
prevents -EPROBE_DEFER from being propagated properly.
Also, notice that platform_get_irq() no longer returns 0 on error:
https://git.kernel.org/pub/scm/linux/kernel/git/torvalds/linux.git/commit/?id=e330b9a6bb35dc7097a4f02cb1ae7b6f96df92af
Print error message and propagate the return value of platform_get_irq
on failure.
This issue was detected with the help of Coccinelle.
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
|
|
According to the gadget.h, a "complete" function will always be called
with interrupts disabled. However, sometimes usb3_request_done() function
is called with interrupts enabled. So, this function should be held
by spin_lock_irqsave() to disable interruption. Also, this driver has
to call spin_unlock() to avoid spinlock recursion by this driver before
calling usb_gadget_giveback_request().
Reported-by: Kazuya Mizuguchi <kazuya.mizuguchi.ks@renesas.com>
Tested-by: Kazuya Mizuguchi <kazuya.mizuguchi.ks@renesas.com>
Fixes: 746bfe63bba3 ("usb: gadget: renesas_usb3: add support for Renesas USB3.0 peripheral controller")
Cc: <stable@vger.kernel.org> # v4.5+
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
|
|
This patch fixes an issue that unexpected behavior happens when
both the interrupt handler and renesas_usb3_ep_enable() are called.
In this case, since usb3_start_pipen() checked the usb3_ep->started,
but the flags was not protected. So, this patch protects the flag
by usb3->lock. Since renesas_usb3_ep_enable() for EP0 will be not called,
this patch doesn't take care of usb3_start_pipe0().
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
|
|
The dedicated dmac can transfer a zero-length-packet (zlp) if some bits
of the USB_COM_CON register. However, the commit 2d4aa21a73ba ("usb:
gadget: udc: renesas_usb3: add support for dedicated DMAC") didn't set
the bits to 1. So, this patch fixes it.
Fixes: 2d4aa21a73b ("usb: gadget: udc: renesas_usb3: add support for dedicated DMAC)
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
|
|
The commit 2d4aa21a73ba ("usb: gadget: udc: renesas_usb3: add support
for dedicated DMAC") has a bug in the renesas_usb3_dma_free_prd().
The size of dma_free_coherent() should be the same with dma_alloc_coherent()
Otherwise, this code causes a WARNING by mm/page_alloc.c when
renesas_usb3_dma_free_prd() is called. So, this patch fixes it.
Fixes: 2d4aa21a73ba ("usb: gadget: udc: renesas_usb3: add support for dedicated DMAC")
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/balbi/usb into usb-testing
Felipe writes:
usb: changes for v4.13 merge window
This time around we have a total of 57 non-merge commits. A list of
most important changes follows:
- Improvements to dwc3 tracing interface
- Initial dual-role support for dwc3
- Improvements to how we handle DMA resources in dwc3
- A new f_uac1 implementation which much more flexible
- Removal of AVR32 bits
- Improvements to f_mass_storage driver
|
|
The USB3.0 peripheral controller on R-Car SoCs has a dedicated DMAC.
The DMAC needs a "PRD table" in system memory and the DMAC can have
four PRD tables. This patch adds support for the DMAC.
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
|
|
The PN_INT_ENA register should be used after usb3_pn_change() is called.
So, this patch moves the access from renesas_usb3_stop_controller() to
usb3_disable_pipe_n().
Fixes: 746bfe63bba3 ("usb: gadget: renesas_usb3: add support for Renesas USB3.0 peripheral controller")
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
|
|
This controller disallows to change the PIPE until reading/writing
a packet finishes. However. the previous code is not enough to hold
the lock in some functions. So, this patch fixes it.
Fixes: 746bfe63bba3 ("usb: gadget: renesas_usb3: add support for Renesas USB3.0 peripheral controller")
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
|
|
This patch fixes an issue that this driver is possible to cause
deadlock by double-spinclocked in renesas_usb3_stop_controller().
So, this patch removes spinlock API calling in renesas_usb3_stop().
(In other words, the previous code had a redundant lock.)
Fixes: 746bfe63bba3 ("usb: gadget: renesas_usb3: add support for Renesas USB3.0 peripheral controller")
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
|
|
This patch fixes an issue that this driver is possible to access
the registers before pm_runtime_get_sync() if a gadget driver is
installed first. After that, oops happens on R-Car Gen3 environment.
To avoid it, this patch changes the pm_runtime call timing from
probe/remove to udc_start/udc_stop.
Fixes: 746bfe63bba3 ("usb: gadget: renesas_usb3: add support for Renesas USB3.0 peripheral controller")
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
|
|
This patch adds support for usb role swap via sysfs "role".
For example:
1) Connect a usb cable using 2 Salvator-X boards.
- For A-Device, the cable is connected to CN11 (USB3.0 ch0).
- For B-Device, the cable is connected to CN9 (USB2.0 ch0).
2) On A-Device, you input the following command:
# echo peripheral > /sys/devices/platform/soc/ee020000.usb/role
3) On B-Device, you input the following command:
# echo host > /sys/devices/platform/soc/ee080200.usb-phy/role
Then, the A-Device acts as a peripheral and the B-Device acts as
a host. Please note that A-Device must input the following command
if you want the board to act as a host again.
# echo host > /sys/devices/platform/soc/ee020000.usb/role
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
|
|
This patch adds extcon support to see VBUS/ID signal states.
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
|
|
This usb 3.0 peripheral controller has a register (USB_OTG_STA) to monitor
the USB ID signal. So, this patch adds the ID signal monitoring to change
the mode to host (A-Host) or peripheral (B-Peripheral).
This patch also removes hardcoded setting as B-Peripheral mode.
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
|
|
Fix typos and add the following to the scripts/spelling.txt:
followings||following
While we are here, add a missing colon in the boilerplate in DT binding
documents. The "you SoC" in allwinner,sunxi-pinctrl.txt was fixed as
well.
I reworded "as the followings:" to "as follows:" for
drivers/usb/gadget/udc/renesas_usb3.c.
Link: http://lkml.kernel.org/r/1481573103-11329-32-git-send-email-yamada.masahiro@socionext.com
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
This driver should clear the bit. Otherwise, the VBUS will output
wrongly if the usb port on a board has VBUS output capability.
Fixes: 746bfe63bba3 ("usb: gadget: renesas_usb3: add support for
Renesas USB3.0 peripheral controller")
Cc: <stable@vger.kernel.org> # v4.5+
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
|
|
R-Car H3 has USB3.0 peripheral controllers. This controller's has the
following features:
- Supports super, high and full speed
- Contains 30 pipes for bulk or interrupt transfer
- Contains dedicated DMA controller
This driver doesn't support the dedicated DMAC for now.
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
|
