summaryrefslogtreecommitdiff
path: root/drivers/usb/dwc2
AgeCommit message (Collapse)Author
2015-04-29usb: dwc2: gadget: remove s3c_hsotg_ep_disable_forceMian Yousaf Kaukab
Force argument is not used anymore. Clean up leftovers from https://lkml.org/lkml/2014/12/9/283 Acked-by: John Youn <johnyoun@synopsys.com> Signed-off-by: Mian Yousaf Kaukab <yousaf.kaukab@intel.com> Signed-off-by: Felipe Balbi <balbi@ti.com>
2015-04-29usb: dwc2: gadget: enable otg flag in dual role configurationGregory Herrero
Inform that device is otg-capable in case of otg configuration. Acked-by: John Youn <johnyoun@synopsys.com> Signed-off-by: Gregory Herrero <gregory.herrero@intel.com> Signed-off-by: Felipe Balbi <balbi@ti.com>
2015-04-29usb: dwc2: gadget: powerup controller if neededGregory Herrero
During vbus session, usb controller needs to exit hibernation if it was previously in suspend state. Since controller will be resetted and configured, there is no need to restore registers. Moreover, set lx_state to L0 on B session. vbus_session callback may not be used by all platforms. Thus, controller software state needs to be set to L0 if the controller detects a valid B session. Otherwise, lx_state will remain L2 and prevent any request submission. Acked-by: John Youn <johnyoun@synopsys.com> Signed-off-by: Gregory Herrero <gregory.herrero@intel.com> Signed-off-by: Felipe Balbi <balbi@ti.com>
2015-04-29usb: dwc2: gadget: prevent new request submission during suspendGregory Herrero
If usb controller is in partial power down, any write to registers may cause unpredictable behavior. Thus, prevent any new request submission once controller is in partial power down. Acked-by: John Youn <johnyoun@synopsys.com> Signed-off-by: Gregory Herrero <gregory.herrero@intel.com> Signed-off-by: Felipe Balbi <balbi@ti.com>
2015-04-29usb: dwc2: gadget: ignore pm suspend/resume in L2Gregory Herrero
Nothing to be done in pm suspend/resume when controller is in L2. Don't disconnect or reset. State is already saved when putting controller in hibernation and will be restored on USB bus resume. Acked-by: John Youn <johnyoun@synopsys.com> Signed-off-by: Gregory Herrero <gregory.herrero@intel.com> Signed-off-by: Felipe Balbi <balbi@ti.com>
2015-04-29usb: dwc2: gadget: use reset detect interruptGregory Herrero
ResetDet interrupt is used to detect a reset of the bus while the controller is suspended. This may happens for example when using Command Verifier. Acked-by: John Youn <johnyoun@synopsys.com> Signed-off-by: Gregory Herrero <gregory.herrero@intel.com> Signed-off-by: Felipe Balbi <balbi@ti.com>
2015-04-29usb: dwc2: set parameter values in probe functionMian Yousaf Kaukab
So the parameters can be used in both host and gadget modes. Also consolidate param functions in the core.h Acked-by: John Youn <johnyoun@synopsys.com> Signed-off-by: Mian Yousaf Kaukab <yousaf.kaukab@intel.com> Signed-off-by: Felipe Balbi <balbi@ti.com>
2015-04-29usb: dwc2: add external_id_pin_ctl core parameterGregory Herrero
This is required due to an Intel specific hardware issue. Where id- pin setup causes glitches on the interrupt line when CONIDSTSCHG interrupt is enabled. Specify external_id_pin_ctl when an external driver (for example phy) can handle id change, so that CONIDSTSCHG interrupt can be disabled from the controller. Acked-by: John Youn <johnyoun@synopsys.com> Signed-off-by: Gregory Herrero <gregory.herrero@intel.com> Signed-off-by: Felipe Balbi <balbi@ti.com>
2015-04-29usb: dwc2: controller must update lx_state before releasing lockGregory Herrero
During suspend, there could a race condition between ep_queue and suspend interrupt if lx_state is updated after releasing spinlock in call_gadget(hsotg, suspend). Acked-by: John Youn <johnyoun@synopsys.com> Signed-off-by: Gregory Herrero <gregory.herrero@intel.com> Signed-off-by: Felipe Balbi <balbi@ti.com>
2015-04-29usb: dwc2: implement hibernation during bus suspend/resumeGregory Herrero
Allow controller to enter in hibernation during usb bus suspend and inform both phy and gadget about the suspended state. While in hibernation, the controller can't detect the resume condition. An external mechanism must call usb_phy_set_suspend on resume. Exit hibernation when controller gets the resume interrupt and inform only gadget driver about it. Acked-by: John Youn <johnyoun@synopsys.com> Signed-off-by: Gregory Herrero <gregory.herrero@intel.com> Signed-off-by: Felipe Balbi <balbi@ti.com>
2015-04-29usb: dwc2: add controller hibernation supportGregory Herrero
When suspending usb bus, phy driver may disable controller power. In this case, registers need to be saved on suspend and restored on resume. Acked-by: John Youn <johnyoun@synopsys.com> Signed-off-by: Gregory Herrero <gregory.herrero@intel.com> Signed-off-by: Felipe Balbi <balbi@ti.com>
2015-04-29usb: dwc2: debugfs: add support for complete register dumpMian Yousaf Kaukab
Dump all registers to take a complete snapshot of dwc2 state. Code is inspired by dwc3/debugfs.c Acked-by: John Youn <johnyoun@synopsys.com> Signed-off-by: Mian Yousaf Kaukab <yousaf.kaukab@intel.com> Signed-off-by: Felipe Balbi <balbi@ti.com>
2015-04-29usb: dwc2: move debugfs code to a separate fileMian Yousaf Kaukab
Prepare to add more debug code. Moreover, don't save dentry * for each file in struct dwc2_hsotg as clean up is done with debugfs_remove_recursive(). s3c_hsotg_delete_debug() is removed altogether for the same reason. Acked-by: John Youn <johnyoun@synopsys.com> Signed-off-by: Mian Yousaf Kaukab <yousaf.kaukab@intel.com> Signed-off-by: Felipe Balbi <balbi@ti.com>
2015-04-10usb: dwc2: host: sleep USB_RESUME_TIMEOUT during resumeGregory Herrero
msleep(USB_RESUME_TIMEOUT) must be done when the controller drives the resume. This is true after HPRT0_RES is written. Moreover, restore the delay after controller power is up. Signed-off-by: Gregory Herrero <gregory.herrero@intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2015-04-10Merge tag 'usb-for-v4.1-part2' of ↵Greg Kroah-Hartman
git://git.kernel.org/pub/scm/linux/kernel/git/balbi/usb into usb-testing Felipe writes: usb: generic resume timeout for v4.1 This part 2 pull request contains only the patches which make sure everybody on linux uses the same resume timeout value. Signed-off-by: Felipe Balbi <balbi@ti.com>
2015-04-07usb: dwc2: hcd: use new USB_RESUME_TIMEOUTFelipe Balbi
Make sure we're using the new macro, so our resume signaling will always pass certification. Cc: <stable@vger.kernel.org> # v3.10+ Signed-off-by: Felipe Balbi <balbi@ti.com>
2015-04-03dwc2: hcd: use USB_DT_HUBSergei Shtylyov
Fix using the bare number to set the 'bDescriptorType' field of the Hub Descriptor while the value is #define'd in <linux/usb/ch11.h>. Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2015-03-24Merge tag 'usb-for-v4.1' of ↵Greg Kroah-Hartman
git://git.kernel.org/pub/scm/linux/kernel/git/balbi/usb into usb-next Felipe writes: usb: patches for v4.1 merge window As usual, a big pile of commits. This time a total of 111 non-merge commits. Other than the usual set of cleanups and non-critical fixes, we have some interesting work for AM335x's MUSB babble recovery. Now that takes a lot less time and we don't have to Reset MUSB all the time. The printer gadget has been converted to configfs interface and the atmel udc has learned suspend/resume with wakeup. Signed-off-by: Felipe Balbi <balbi@ti.com>
2015-03-19usb: dwc2: pci: Correctly compile dwc2-pci as a module or built-inJohn Youn
The dwc2-pci driver should be compiled as a module when configured to do so. If the dwc2-pci is configured as a module but actually built-in, it can cause build errors due to the fact that the generic-phy will be allowed to compile as a module causing undefined references. Reported-by: Alan Cox <alan@lxorguk.ukuu.org.uk> Signed-off-by: John Youn <johnyoun@synopsys.com> Signed-off-by: Felipe Balbi <balbi@ti.com>
2015-03-19usb: dwc2: avoid leaking DMA channels on disconnectionVincent Palatin
When the HCD is disconnected, the DMA transfers still in-flight were cleaned-up but the count of available DMA channels (e.g. available_host_channels) was not reset. The pool of DMA channels can be depleted when doing unclean disconnection of USB peripherals, and reaches the point where no transfer was possible until the next reboot/reload of the driver. Tested by putting a programmable USB mux on the port and randomly plugging/unpluging a USB HUB with USB mass-storage key, USB-audio and USB-ethernet dongle connected to its downstream ports, and also doing the disconnection early while the devices are still enumerating to get more URBs in-flight. After the patch, the devices are still enumerating after thousands of cycles, while the port was totally dead before. Signed-off-by: Vincent Palatin <vpalatin@chromium.org> Acked-by: John Youn <johnyoun@synopsys.com> Signed-off-by: Felipe Balbi <balbi@ti.com>
2015-03-13usb: dwc2: pci: Select the generic PHY for dwc2-pci driverJohn Youn
The dwc2-pci driver requires the generic PHY. This fixes undefined reference issues when it is not selected. Reported-by: kbuild test robot <fengguang.wu@intel.com> Signed-off-by: John Youn <johnyoun@synopsys.com> Signed-off-by: Felipe Balbi <balbi@ti.com>
2015-03-12usb: dwc2: rework initialization of host and gadget in dual-role modeMarek Szyprowski
If device is configured to work only in HOST or DEVICE mode, there is no point in initializing both subdrivers. This patch also fixes resource leakage if host subdriver fails to initialize. Acked-by: John Youn <johnyoun@synopsys.com> Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com> Signed-off-by: Felipe Balbi <balbi@ti.com>
2015-03-11usb: dwc2: pci: Add device mode to the dwc2-pci driverJohn Youn
The pci driver now registers a platform driver, like in dwc3, and lets its probe function do all the initialization. This allows it to account for changes to the platform driver that were not added to the pci driver. Also future changes to the probe function don't have to be duplicated. This also has the effect of adding device and DRD mode to the pci driver. Tested on the Synopsys HAPS PCIe platform. Signed-off-by: John Youn <johnyoun@synopsys.com> Signed-off-by: Felipe Balbi <balbi@ti.com>
2015-03-10usb: dwc2: host: fix dwc2 disconnect bugYunzhi Li
When dwc2 controller detects a disconnect interrupt, dwc2_hcd_disconnect() should be called immediately to do clean-up jobs and set port_connect_status_change flag to notify usb hub driver disconnect status. Tested-by: Vincent Palatin <vpalatin@chromium.org> Acked-by: John Youn <johnyoun@synopsys.com> Signed-off-by: Yunzhi Li <lyz@rock-chips.com> Signed-off-by: Felipe Balbi <balbi@ti.com>
2015-03-10usb: move definition of PCI_VENDOR_ID_SYNOPSYS to linux/pci_ids.hJoseph Kogut
Removed FIXME from usb/dwc3/dwc3-pci.c by moving definition of PCI_VENDOR_ID_SYNOPSYS shared with usb/dwc2 to linux/pci_ids.h. Signed-off-by: Joseph Kogut <joseph.kogut@gmail.com> Signed-off-by: Felipe Balbi <balbi@ti.com>
2015-02-04Merge tag 'usb-for-v3.20' of ↵Greg Kroah-Hartman
git://git.kernel.org/pub/scm/linux/kernel/git/balbi/usb into usb-next Felipe writes: usb: patches for v3.20 merge window Here's the big pull request for Gadgets and PHYs. It's a total of 217 non-merge commits with pretty much everything being touched. The most important bits are a ton of new documentation for almost all usb gadget functions, a new isp1760 UDC driver, several improvements to the old net2280 UDC driver, and some minor tracepoint improvements to dwc3. Other than that, a big list of minor cleanups, smaller bugfixes and new features all over the place. Signed-off-by: Felipe Balbi <balbi@ti.com>
2015-02-04usb: dwc2: Fix a bug in reading the endpoint directions from reg.Roshan Pius
According to the DWC2 datasheet, the HWCFG1 register stores the configured endpoint directions for endpoints 0-15 in bit positions 0-31. ========================== Endpoint Direction (EpDir) This 32-bit field uses two bits per endpoint to determine the endpoint direction. Endpoint Bits [31:30]: Endpoint 15 direction Bits [29:28]: Endpoint 14 direction .... Bits [3:2]: Endpoint 1 direction Bits[1:0]: Endpoint 0 direction (always BIDIR) ========================== The DWC2 driver is currently interpreting the contents of the register as directions for endpoints 1-15 which leads to an error in determining the configured endpoint directions in the core because the first 2 bits determine the direction of endpoint 0 and not 1. This is based on testing/next branch in Felipe's git. Signed-off-by: Roshan Pius <rpius@chromium.org> Acked-by: John Youn <johnyoun@synopsys.com> Signed-off-by: Felipe Balbi <balbi@ti.com>
2015-02-02Merge 3.19-rc7 into usb-nextGreg Kroah-Hartman
We want the USB fixes in here to make merges easier. Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2015-01-30usb: dwc2: fix USB core dependenciesArnd Bergmann
It is currently possible to configure the dwc2 driver as built-in when host mode or dual-role is enabled, but the USB core is a loadable module. This leads to a link failure: drivers/built-in.o: In function `_dwc2_hcd_start': :(.text+0x84538): undefined reference to `usb_hcd_resume_root_hub' drivers/built-in.o: In function `_dwc2_hcd_urb_dequeue': :(.text+0x84aa0): undefined reference to `usb_hcd_check_unlink_urb' :(.text+0x84e4c): undefined reference to `usb_hcd_unlink_urb_from_ep' :(.text+0x84e74): undefined reference to `usb_hcd_giveback_urb' drivers/built-in.o: In function `dwc2_assign_and_init_hc': :(.text+0x86b98): undefined reference to `usb_hcd_unmap_urb_for_dma' drivers/built-in.o: In function `_dwc2_hcd_urb_enqueue': :(.text+0x8717c): undefined reference to `usb_hcd_link_urb_to_ep' :(.text+0x872f4): undefined reference to `usb_hcd_unlink_urb_from_ep' drivers/built-in.o: In function `dwc2_host_complete': :(.text+0x875d4): undefined reference to `usb_hcd_unlink_urb_from_ep' :(.text+0x87600): undefined reference to `usb_hcd_giveback_urb' drivers/built-in.o: In function `dwc2_hcd_init': :(.text+0x87ba8): undefined reference to `usb_disabled' :(.text+0x87d38): undefined reference to `usb_create_hcd' :(.text+0x88094): undefined reference to `usb_add_hcd' :(.text+0x880dc): undefined reference to `usb_put_hcd' drivers/built-in.o: In function `dwc2_hcd_remove': :(.text+0x8821c): undefined reference to `usb_remove_hcd' :(.text+0x8823c): undefined reference to `usb_put_hcd' drivers/built-in.o: In function `dwc2_hc_handle_tt_clear.isra.10': :(.text+0x88e2c): undefined reference to `usb_hub_clear_tt_buffer' drivers/built-in.o: In function `dwc2_hcd_qtd_add': :(.text+0x8b554): undefined reference to `usb_calc_bus_time' To fix the problem, this patch changes the dependencies so that dwc2 host mode can only be enabled if either the USB core is built-in or both USB and dwc2 are modules. Acked-by: John Youn <johnyoun@synopsys.com> Signed-off-by: Arnd Bergmann <arnd@arndb.de> Signed-off-by: Felipe Balbi <balbi@ti.com>
2015-01-30usb: dwc2: gadget: initialize controller in pullup callbackGregory Herrero
USB reset interrupt is no more used to reset the controller. Thus, reset the controller in pullup callback as described by Synopsys programming guide. Otherwise enumeration sometimes fails when usb configuration is switched without physical disconnection. Tested-by: Robert Baldyga <r.baldyga@samsung.com> Acked-by: John Youn <johnyoun@synopsys.com> Signed-off-by: Gregory Herrero <gregory.herrero@intel.com> Signed-off-by: Felipe Balbi <balbi@ti.com>
2015-01-30usb: dwc2: gadget: replace constants with definesMian Yousaf Kaukab
Defines are more readable and searchable than constants. Tested-by: Robert Baldyga <r.baldyga@samsung.com> Acked-by: John Youn <johnyoun@synopsys.com> Signed-off-by: Mian Yousaf Kaukab <yousaf.kaukab@intel.com> Signed-off-by: Felipe Balbi <balbi@ti.com>
2015-01-30usb: dwc2: gadget: fix phy interface configurationMian Yousaf Kaukab
hsotg->phyif is set in dwc2_gadget_init according to phy interface width. Use it for configuration instead of hardcoded value. Moreover, set USB turnaround time according to phy width. Tested-by: Robert Baldyga <r.baldyga@samsung.com> Acked-by: John Youn <johnyoun@synopsys.com> Signed-off-by: Mian Yousaf Kaukab <yousaf.kaukab@intel.com> Signed-off-by: Felipe Balbi <balbi@ti.com>
2015-01-30usb: dwc2: gadget: fix debug message for zlpMian Yousaf Kaukab
Print debug message according to zlp direction. Always saying "Sending" is misleading. Tested-by: Robert Baldyga <r.baldyga@samsung.com> Acked-by: John Youn <johnyoun@synopsys.com> Signed-off-by: Mian Yousaf Kaukab <yousaf.kaukab@intel.com> Signed-off-by: Felipe Balbi <balbi@ti.com>
2015-01-30usb: dwc2: gadget: don't modify pullup status during resetGregory Herrero
Pullup doesn't need to be enabled during usb reset since it is already enabled. This leads to shorter chirp-k duration if done during usb reset. Tested-by: Robert Baldyga <r.baldyga@samsung.com> Acked-by: John Youn <johnyoun@synopsys.com> Signed-off-by: Gregory Herrero <gregory.herrero@intel.com> Signed-off-by: Felipe Balbi <balbi@ti.com>
2015-01-30usb: dwc2: gadget: add reset flag in init functionGregory Herrero
Add a flag to request physical reset of the controller when s3c_hsotg_core_init_disconnected is called. During the usb reset, controller must not be fully reconfigured and resetted. Else this leads to shorter chirp-k duration during enumeration. Tested-by: Robert Baldyga <r.baldyga@samsung.com> Acked-by: John Youn <johnyoun@synopsys.com> Signed-off-by: Gregory Herrero <gregory.herrero@intel.com> Signed-off-by: Mian Yousaf Kaukab <yousaf.kaukab@intel.com> Signed-off-by: Felipe Balbi <balbi@ti.com>
2015-01-30usb: dwc2: gadget: add unaligned buffers supportMian Yousaf Kaukab
When using DMA, dwc2 requires buffers to be 4 bytes aligned. Use bounce buffers if they are not. Tested-by: Robert Baldyga <r.baldyga@samsung.com> Acked-by: John Youn <johnyoun@synopsys.com> Signed-off-by: Mian Yousaf Kaukab <yousaf.kaukab@intel.com> Signed-off-by: Felipe Balbi <balbi@ti.com>
2015-01-30usb: dwc2: gadget: remove hardcoded if (0) and if (1) checksMian Yousaf Kaukab
Remove dead code as well. Tested-by: Robert Baldyga <r.baldyga@samsung.com> Acked-by: John Youn <johnyoun@synopsys.com> Signed-off-by: Mian Yousaf Kaukab <yousaf.kaukab@intel.com> Signed-off-by: Felipe Balbi <balbi@ti.com>
2015-01-30usb: dwc2: gadget: fix a typo in commentGregory Herrero
s3c_hsotg_process_req_feature comments was not correct Tested-by: Robert Baldyga <r.baldyga@samsung.com> Acked-by: John Youn <johnyoun@synopsys.com> Signed-off-by: Gregory Herrero <gregory.herrero@intel.com> Signed-off-by: Felipe Balbi <balbi@ti.com>
2015-01-30usb: dwc2: gadget: add TEST_MODE feature supportGregory Herrero
Handle SET_FEATURE TEST_MODE request sent by the host. Slightly rework FEATURE request handling to allow parsing other request types than Endpoint. Also add a debugfs to change test mode value from user space. Tested-by: Robert Baldyga <r.baldyga@samsung.com> Acked-by: John Youn <johnyoun@synopsys.com> Signed-off-by: Gregory Herrero <gregory.herrero@intel.com> Signed-off-by: Felipe Balbi <balbi@ti.com>
2015-01-30usb: dwc2: gadget: fix clear halt feature handlingGregory Herrero
When clearing HALT on an endpoint, req->complete of in progress requests must be called with locks off. New request should only be started if there is not already a pending request on the endpoint. Tested-by: Robert Baldyga <r.baldyga@samsung.com> Acked-by: John Youn <johnyoun@synopsys.com> Signed-off-by: Gregory Herrero <gregory.herrero@intel.com> Signed-off-by: Felipe Balbi <balbi@ti.com>
2015-01-30usb: dwc2: host: resume root hub on remote wakeupGregory Herrero
When a remote wakeup happens during bus_suspend, hcd needs to resume its root hub. Acked-by: John Youn <johnyoun@synopsys.com> Signed-off-by: Gregory Herrero <gregory.herrero@intel.com> Signed-off-by: Felipe Balbi <balbi@ti.com>
2015-01-25dwc2: hcd: use HUB_CHAR_*Sergei Shtylyov
Fix using the bare number to set the 'wHubCharacteristics' field of the Hub Descriptor while the values are #define'd in <linux/usb/ch11.h>. Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2015-01-19usb: dwc2: hcd: use HUB_CHAR_*Sergei Shtylyov
Fix using the bare number to set the 'wHubCharacteristics' field of the Hub Descriptor while the values are #define'd in <linux/usb/ch11.h>. Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com> Signed-off-by: Felipe Balbi <balbi@ti.com>
2015-01-19Revert "usb: dwc2: add bus suspend/resume for dwc2"Paul Zimmerman
This reverts commit 0cf884e819e05437287a668b9bfcc198bab6329c. Even after applying the follow-on patch at https://patchwork.kernel.org/patch/5325111 there are still problems with device connect on the Altera SOCFPGA platform at least. One possible fix would be to add a whitelist to enable suspend/resume on platforms where it does work correctly. Signed-off-by: Paul Zimmerman <paulz@synopsys.com> Signed-off-by: Felipe Balbi <balbi@ti.com>
2015-01-19Merge tag 'v3.19-rc5' into nextFelipe Balbi
Linux 3.19-rc5 Conflicts: drivers/usb/dwc2/gadget.c drivers/usb/gadget/udc/bdc/bdc_ep.c
2015-01-19usb: dwc2: call dwc2_is_controller_alive() under spinlockRobert Baldyga
This patch fixes the following problem: data transmission in direction IN break unless the GSNPSID register access is done with spinlock held. This issue occurs at least in Exynos4412 SoC, probably in many SoC's from Exynos familly. The problem is described here: https://lkml.org/lkml/2014/12/22/185 And there is linux mailing list discussion: https://lkml.org/lkml/2015/1/14/17 Signed-off-by: Robert Baldyga <r.baldyga@samsung.com> Signed-off-by: Felipe Balbi <balbi@ti.com>
2015-01-12usb: dwc2: gadget: report disconnection after resetMian Yousaf Kaukab
If usb bus is reset without a physical disconnection, all endpoints will remain open. Call s3c_hsotg_disconnect() from reset handler to report a disconnect to gadget framework. hsotg->connected is checked in s3c_hsotg_disconnect() before processing disconnect. In some cases, USBRst is seen before EnumDone and after it as well. So move setting of hsotg->connected to set-address to avoid reporting extra disconnection in this case. Tested-by: Robert Baldyga <r.baldyga@samsung.com> Acked-by: Paul Zimmerman <paulz@synopsys.com> Signed-off-by: Mian Yousaf Kaukab <yousaf.kaukab@intel.com> Signed-off-by: Felipe Balbi <balbi@ti.com>
2015-01-12usb: dwc2: gadget: force gadget initialization in dev modeGregory Herrero
When booting with id pin grounded, dwc2 default to host mode. Thus, force device mode prior initializing gadget part. Else fifo init will fail since fifo values are not correct in host mode. Tested-by: Robert Baldyga <r.baldyga@samsung.com> Acked-by: Paul Zimmerman <paulz@synopsys.com> Signed-off-by: Gregory Herrero <gregory.herrero@intel.com> Signed-off-by: Felipe Balbi <balbi@ti.com>
2015-01-12usb: dwc2: gadget: add vbus_draw supportGregory Herrero
This callback informs the driver about the total amount of current it is allowed to draw. Share this information with the phy so that current limits can be set for charging for example. Tested-by: Robert Baldyga <r.baldyga@samsung.com> Acked-by: Paul Zimmerman <paulz@synopsys.com> Signed-off-by: Gregory Herrero <gregory.herrero@intel.com> Signed-off-by: Felipe Balbi <balbi@ti.com>
2015-01-12usb: dwc2: gadget: fix pullup handlingGregory Herrero
Gadget must be informed about disconnection when pullup is removed. Tested-by: Robert Baldyga <r.baldyga@samsung.com> Acked-by: Paul Zimmerman <paulz@synopsys.com> Signed-off-by: Gregory Herrero <gregory.herrero@intel.com> Signed-off-by: Felipe Balbi <balbi@ti.com>
generated by cgit v1.2.3 (git 2.39.1) at 2025-08-04 14:33:53 +0000