| Age | Commit message (Collapse) | Author |
|---|
|
We initiate dwc2 usb controller in BIOS, dwc2_core_reset() should
be called before dwc2_get_hwparams() to reset core registers to
default value. Without this the FIFO setting might be incorrect
because calculating FIFO size need power-on value of
GRXFSIZ/GNPTXFSIZ/HPTXFSIZ registers.
This patch could avoid warnning massage like in rk3288 platform:
[ 2.074764] dwc2 ff580000.usb: 256 invalid for
host_perio_tx_fifo_size. Check HW configuration.
Signed-off-by: Yunzhi Li <lyz@rock-chips.com>
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Signed-off-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
|
|
Support hisilicon,hi6220-usb for HiKey board
Acked-by: Rob Herring <robh@kernel.org>
Acked-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Zhangfei Gao <zhangfei.gao@linaro.org>
Signed-off-by: Felipe Balbi <balbi@ti.com>
|
|
As descriptor dma mode does not support split transfers, it can't be
enabled for high speed devices. Add a core parameter to enable it for
full speed devices.
Ensure frame list and descriptor list are correctly freed during
disconnect.
Acked-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Mian Yousaf Kaukab <yousaf.kaukab@intel.com>
Signed-off-by: Gregory Herrero <gregory.herrero@intel.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
|
|
This patch make sure that all necessary members of dwc2_hsotg
are initialized before the irq handler is requested. So
the kernel oops triggered by dwc2_handle_common_intr has
been fixed.
dwc2 20980000.usb: Configuration mismatch. Forcing host mode
dwc2 20980000.usb: no platform data or transceiver defined
Unable to handle kernel paging request at virtual address cc860040
pgd = c0004000
[cc860040] *pgd=0b41e811, *pte=00000000, *ppte=00000000
Internal error: Oops: 7 [#1] ARM
CPU: 0 PID: 1 Comm: swapper Not tainted 4.3.0-rc3+ #19
Hardware name: BCM2835
task: cb494000 ti: cb4d0000 task.ti: cb4d0000
PC is at dwc2_is_controller_alive+0x18/0x34
LR is at dwc2_handle_common_intr+0x24/0xb60
Acked-by: John Youn <johnyoun@synopsys.com>
Tested-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Stefan Wahren <stefan.wahren@i2se.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
|
|
Fixes commit 09a75e857790
("usb: dwc2: refactor common low-level hw code to platform.c")
The above commit consolidated the low-level phy access into a common
location. This change made the otg clk a requirement and broke some
platforms when it was moved into platform.c.
So make clk handling optional again.
Acked-by: Eric Anholt <eric@anholt.net>
Signed-off-by: Stefan Wahren <stefan.wahren@i2se.com>
Cc: Marek Szyprowski <m.szyprowski@samsung.com>
Acked-by: John Youn <johnyoun@synopsys.com>
Tested-by: Marek Szyprowski <m.szyprowski@samsung.com>
Fixes: 09a75e857790 ("usb: dwc2: refactor common low-level hw code to platform.c")
Signed-off-by: Felipe Balbi <balbi@ti.com>
|
|
When searching for PHYs, any error was treated as if the PHY did not
exist or was not specified. Thus the probe function did not
correctly return error conditions such as -EPROBE_DEFER.
Fixed so that only a non-existing PHY is ignored and any other error
is returned.
Acked-by: Eric Anholt <eric@anholt.net>
Reported-by: Alexander Aring <alex.aring@gmail.com>
Signed-off-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Stefan Wahren <stefan.wahren@i2se.com>
Tested-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
|
|
Fixes commit 09a75e857790
("usb: dwc2: refactor common low-level hw code to platform.c")
The above commit consolidated the low-level phy access into a common
location. This change introduced a check from the gadget requiring
that a PHY is specified. This requirement never existed on the host
side and broke some platforms when it was moved into platform.c.
The gadget doesn't require the PHY either so remove the check.
Acked-by: Eric Anholt <eric@anholt.net>
Reported-by: Stefan Wahren <info@lategoodbye.de>
Cc: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: John Youn <johnyoun@synopsys.com>
Tested-by: Marek Szyprowski <m.szyprowski@samsung.com>
Fixes: 09a75e857790 ("usb: dwc2: refactor common low-level hw code to platform.c")
Signed-off-by: Felipe Balbi <balbi@ti.com>
|
|
The comment for ahbcfg for rk3066 parameters (also used for rk3288)
claimed that ahbcfg was INCR16, but it wasn't. Since the bits weren't
shifted properly, the 0x7 ended up being masked and we ended up
programming 0x3 for the HBstLen. Let's set it to INCR16 properly.
As per Wu Liang Feng at Rockchip this may increase transmission
efficiency. I did blackbox tests with writing 0s to a USB-based SD
reader (forcefully capping CPU Freq to try to measure efficiency):
cd /sys/devices/system/cpu/cpu0/cpufreq
echo userspace > scaling_governor
echo 126000 > scaling_setspeed
for i in $(seq 10); do
dd if=/dev/zero of=/dev/sdb bs=1M count=750
done
With the above tests I found that speeds went from ~15MB/s to ~18MB/s.
Note that most other tests I did (including reading from the same USB
reader) didn't show any difference in performance.
Tested-by: Heiko Stuebner <heiko@sntech.de>
Acked-by: John Youn <johnyoun@synopsys.com>
Reviewed-by: Liangfeng Wu <wulf@rock-chips.com>
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Felipe Balbi <balbi@ti.com>
|
|
DWC2 module on some platforms needs three additional hardware
resources: phy controller, clock and power supply. All of them must be
enabled/activated to properly initialize and operate. This was initially
handled in s3c-hsotg driver, which has been converted to 'gadget' part
of dwc2 driver. Unfortunately, not all of this code got moved to common
platform code, what resulted in accessing DWC2 registers without
enabling low-level hardware resources. This fails for example on Exynos
SoCs. This patch moves all the code for managing those resources to
common platform.c file and provides convenient wrappers for controlling
them.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Acked-by: John Youn <johnyoun@synopsys.com>
Tested-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
|
|
init_mutex is a leftover from the time, when s3c-hsotg driver did not
implement proper pull up/down control and emulated it by enabling
enabling/disabling usb phy. Proper pull up/down control has been added
by commit 5b9451f8c4fbaf0549139755fb45ff2b57975b7f ("usb: dwc2: gadget:
use soft-disconnect udc feature in pullup() method"), so init_muxtex can
be removed now to avoid potential deadlocks with other locks.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Acked-by: John Youn <johnyoun@synopsys.com>
Tested-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
|
|
Even when DWC2 is in (internal) suspended state, it should disable PHY
in suspend and then enable it in resume. This patch fixes unbalanced PHY
control sequence.
Tested-by: John Youn <johnyoun@synopsys.com>
Acked-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
|
|
If dual role configuration is not selected, check and force dr_mode
based on the selected configuration.
Signed-off-by: Mian Yousaf Kaukab <yousaf.kaukab@intel.com>
Tested-by: Robert Baldyga <r.baldyga@samsung.com>
Tested-by: Dinh Nguyen <dinguyen@opensource.altera.com>
Tested-by: John Youn <johnyoun@synopsys.com>
Acked-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
|
|
By using the unified device property interface, the function
can be made available for all platforms and not just the
ones using DT.
Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
|
|
this driver has long ago became dwc2.ko with
both peripheral and host roles, there's no point
in keeping the old function names.
Acked-by: John Youn <johnyoun@synopsys.com>
Tested-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
|
|
dwc2 may not be able to exit from hibernation if the hardware
does not provide a way to detect resume signalling in this state.
Thus, add the possibility to disable hibernation feature.
Acked-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Gregory Herrero <gregory.herrero@intel.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
|
|
So the parameters can be used in both host and gadget modes.
Also consolidate param functions in the core.h
Acked-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Mian Yousaf Kaukab <yousaf.kaukab@intel.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
|
|
This is required due to an Intel specific hardware issue. Where id-
pin setup causes glitches on the interrupt line when CONIDSTSCHG
interrupt is enabled.
Specify external_id_pin_ctl when an external driver (for example phy)
can handle id change, so that CONIDSTSCHG interrupt can be disabled
from the controller.
Acked-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Gregory Herrero <gregory.herrero@intel.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
|
|
Prepare to add more debug code. Moreover, don't save dentry * for
each file in struct dwc2_hsotg as clean up is done with
debugfs_remove_recursive(). s3c_hsotg_delete_debug() is removed
altogether for the same reason.
Acked-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Mian Yousaf Kaukab <yousaf.kaukab@intel.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
|
|
If device is configured to work only in HOST or DEVICE mode, there is
no point in initializing both subdrivers. This patch also fixes
resource leakage if host subdriver fails to initialize.
Acked-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
|
|
Get PHY parameters from devicetree and power off usb PHY during
system suspend.
Acked-by: Paul Zimmerman <paulz@synopsys.com>
Signed-off-by: Yunzhi Li <lyz@rock-chips.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
|
|
Building with bcm2835_defconfig, which has CONFIG_PM_SLEEP=n causes the
following build warning:
drivers/usb/dwc2/platform.c:227:12: warning: 'dwc2_suspend' defined but not used [-Wunused-function]
drivers/usb/dwc2/platform.c:237:12: warning: 'dwc2_resume' defined but not used [-Wunused-function]
Annotate these functions with '__maybe_unused' to prevent the warnings.
Reported-by: Olof's autobuilder <build@lixom.net>
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
|
|
This patch adds mutex, which protects initialization and
deinitialization procedures against suspend/resume methods. This mutex
will be needed by the updated suspend/resume calls, which tracks gadget
state.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Acked-by: Paul Zimmerman <paulz@synopsys.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
|
|
Since platform.c will get built for both Host and Gadget, if we leave the
usb_disabled() call in platform.c, it results in the following build error
when (!USB && USB_GADGET) condition is met.
ERROR: "usb_disabled" [drivers/usb/dwc2/dwc2_platform.ko] undefined!
Since usb_disabled() is mostly used to disable USB host functionality, move
the call the host portion for the DWC2 driver.
Acked-by: Paul Zimmerman <paulz@synopsys.com>
Signed-off-by: Dinh Nguyen <dinguyen@opensource.altera.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
|
|
Make dwc2_handle_common_intr call the gadget interrupt function when operating
in peripheral mode. Remove the spinlock functions in s3c_hsotg_irq as
dwc2_handle_common_intr() already has the spinlocks.
Move the registeration of the IRQ to common code for platform and PCI.
Remove duplicate interrupt conditions that was in gadget, as those are handled
by dwc2 common interrupt handler.
Acked-by: Paul Zimmerman <paulz@synopsys.com>
Signed-off-by: Dinh Nguyen <dinguyen@opensource.altera.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
|
|
Update suspend/resume to use dev_pm_ops API.
Acked-by: Paul Zimmerman <paulz@synopsys.com>
Signed-off-by: Dinh Nguyen <dinguyen@opensource.altera.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
|
|
This patch will aggregate the probing of gadget/hcd driver into platform.c.
The gadget probe funtion is converted into gadget_init that is now only
responsible for gadget only initialization. All the gadget resources are now
handled by platform.c
Since the host workqueue will not get initialized if the driver is configured
for peripheral mode only. Thus we need to check for wq_otg before calling
queue_work().
Also, we move spin_lock_init to common location for both host and gadget that
is either in platform.c or pci.c.
We also move suspend/resume code to common platform code.
Lastly, move the "samsung,s3c6400-hsotg" binding into dwc2_of_match_table.
Signed-off-by: Dinh Nguyen <dinguyen@opensource.altera.com>
Acked-by: Paul Zimmerman <paulz@synopsys.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
|
|
This reverts commit 8df438571cdbd5c4fcd1b25b19eea1ad5c3cf777.
This patch breaks building dwc2 driver in gadget mode at samsung
platforms.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Move the "samsung,s3c6400-hsotg" binding as the probe function in the gadget
driver will get removed when the dual-role driver is implemented.
Signed-off-by: Dinh Nguyen <dinguyen@opensource.altera.com>
Acked-by: Paul Zimmerman <paulz@synopsys.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
According to the "dr_mode", the otg controller can work as
device role and host role. Some boards always want to use host mode
and some other boards want to use gadget mode. We use the dts setting
to set dwc2's mode, rather than fixing it to whatever hardware says.
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
Acked-by: Paul Zimmerman <paulz@synopsys.com>
Tested-by: Doug Anderson <dianders@chromium.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
This patch add compatible data for dwc2 controller found on
rk3066, rk3188 and rk3288 processors from rockchip.
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
Acked-by: Paul Zimmerman <paulz@synopsys.com>
Reviewed-by: Doug Anderson <dianders@chromium.org>
Tested-by: Doug Anderson <dianders@chromium.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Even though the IP supports Descriptor DMA mode, it does not support SPLIT
transactions in this mode. So the driver, in its currently form, will not
support LS/FS devices when connected to a HS Hub if Descriptor DMA mode is
enabled.
So we should just default to disable descriptor dma mode.
Signed-off-by: Dinh Nguyen <dinguyen@altera.com>
Acked-by: Paul Zimmerman <paulz@synopsys.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Add usb_disabled() check to prevent kernel oops when booting with "nousb"
in the cmdline:
Unable to handle kernel NULL pointer dereference at virtual address 00000030
...
PC is at bus_add_device+0xe0/0x18c
LR is at device_add_groups+0x1c/0x20
...
[<c02191c0>] (bus_add_device) from [<c0217130>] (device_add+0x41c/0x538)
[<c0217130>] (device_add) from [<c023b1d4>] (usb_new_device+0x270/0x35c)
[<c023b1d4>] (usb_new_device) from [<c0241174>] (usb_add_hcd+0x4fc/0x760)
[<c0241174>] (usb_add_hcd) from [<c0254ce0>] (dwc2_hcd_init+0x434/0x510)
[<c0254ce0>] (dwc2_hcd_init) from [<c02594f4>] (dwc2_driver_probe+0x130/0x170)
[<c02594f4>] (dwc2_driver_probe) from [<c021bbd0>] (platform_drv_probe+0x28/0x58)
Signed-off-by: Andre Heider <a.heider@gmail.com>
Acked-by: Paul Zimmerman <paulz@synopsys.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
The DWC2 driver should now be in good enough shape to move out of
staging. I have stress tested it overnight on RPI running mass
storage and Ethernet transfers in parallel, and for several days
on our proprietary PCI-based platform.
Signed-off-by: Paul Zimmerman <paulz@synopsys.com>
Cc: Felipe Balbi <balbi@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
