summaryrefslogtreecommitdiff
path: root/drivers/usb/dwc2/gadget.c
AgeCommit message (Collapse)Author
2015-04-29usb: dwc2: gadget: powerup controller if neededGregory Herrero
During vbus session, usb controller needs to exit hibernation if it was previously in suspend state. Since controller will be resetted and configured, there is no need to restore registers. Moreover, set lx_state to L0 on B session. vbus_session callback may not be used by all platforms. Thus, controller software state needs to be set to L0 if the controller detects a valid B session. Otherwise, lx_state will remain L2 and prevent any request submission. Acked-by: John Youn <johnyoun@synopsys.com> Signed-off-by: Gregory Herrero <gregory.herrero@intel.com> Signed-off-by: Felipe Balbi <balbi@ti.com>
2015-04-29usb: dwc2: gadget: prevent new request submission during suspendGregory Herrero
If usb controller is in partial power down, any write to registers may cause unpredictable behavior. Thus, prevent any new request submission once controller is in partial power down. Acked-by: John Youn <johnyoun@synopsys.com> Signed-off-by: Gregory Herrero <gregory.herrero@intel.com> Signed-off-by: Felipe Balbi <balbi@ti.com>
2015-04-29usb: dwc2: gadget: ignore pm suspend/resume in L2Gregory Herrero
Nothing to be done in pm suspend/resume when controller is in L2. Don't disconnect or reset. State is already saved when putting controller in hibernation and will be restored on USB bus resume. Acked-by: John Youn <johnyoun@synopsys.com> Signed-off-by: Gregory Herrero <gregory.herrero@intel.com> Signed-off-by: Felipe Balbi <balbi@ti.com>
2015-04-29usb: dwc2: gadget: use reset detect interruptGregory Herrero
ResetDet interrupt is used to detect a reset of the bus while the controller is suspended. This may happens for example when using Command Verifier. Acked-by: John Youn <johnyoun@synopsys.com> Signed-off-by: Gregory Herrero <gregory.herrero@intel.com> Signed-off-by: Felipe Balbi <balbi@ti.com>
2015-04-29usb: dwc2: move debugfs code to a separate fileMian Yousaf Kaukab
Prepare to add more debug code. Moreover, don't save dentry * for each file in struct dwc2_hsotg as clean up is done with debugfs_remove_recursive(). s3c_hsotg_delete_debug() is removed altogether for the same reason. Acked-by: John Youn <johnyoun@synopsys.com> Signed-off-by: Mian Yousaf Kaukab <yousaf.kaukab@intel.com> Signed-off-by: Felipe Balbi <balbi@ti.com>
2015-02-04usb: dwc2: Fix a bug in reading the endpoint directions from reg.Roshan Pius
According to the DWC2 datasheet, the HWCFG1 register stores the configured endpoint directions for endpoints 0-15 in bit positions 0-31. ========================== Endpoint Direction (EpDir) This 32-bit field uses two bits per endpoint to determine the endpoint direction. Endpoint Bits [31:30]: Endpoint 15 direction Bits [29:28]: Endpoint 14 direction .... Bits [3:2]: Endpoint 1 direction Bits[1:0]: Endpoint 0 direction (always BIDIR) ========================== The DWC2 driver is currently interpreting the contents of the register as directions for endpoints 1-15 which leads to an error in determining the configured endpoint directions in the core because the first 2 bits determine the direction of endpoint 0 and not 1. This is based on testing/next branch in Felipe's git. Signed-off-by: Roshan Pius <rpius@chromium.org> Acked-by: John Youn <johnyoun@synopsys.com> Signed-off-by: Felipe Balbi <balbi@ti.com>
2015-01-30usb: dwc2: gadget: initialize controller in pullup callbackGregory Herrero
USB reset interrupt is no more used to reset the controller. Thus, reset the controller in pullup callback as described by Synopsys programming guide. Otherwise enumeration sometimes fails when usb configuration is switched without physical disconnection. Tested-by: Robert Baldyga <r.baldyga@samsung.com> Acked-by: John Youn <johnyoun@synopsys.com> Signed-off-by: Gregory Herrero <gregory.herrero@intel.com> Signed-off-by: Felipe Balbi <balbi@ti.com>
2015-01-30usb: dwc2: gadget: replace constants with definesMian Yousaf Kaukab
Defines are more readable and searchable than constants. Tested-by: Robert Baldyga <r.baldyga@samsung.com> Acked-by: John Youn <johnyoun@synopsys.com> Signed-off-by: Mian Yousaf Kaukab <yousaf.kaukab@intel.com> Signed-off-by: Felipe Balbi <balbi@ti.com>
2015-01-30usb: dwc2: gadget: fix phy interface configurationMian Yousaf Kaukab
hsotg->phyif is set in dwc2_gadget_init according to phy interface width. Use it for configuration instead of hardcoded value. Moreover, set USB turnaround time according to phy width. Tested-by: Robert Baldyga <r.baldyga@samsung.com> Acked-by: John Youn <johnyoun@synopsys.com> Signed-off-by: Mian Yousaf Kaukab <yousaf.kaukab@intel.com> Signed-off-by: Felipe Balbi <balbi@ti.com>
2015-01-30usb: dwc2: gadget: fix debug message for zlpMian Yousaf Kaukab
Print debug message according to zlp direction. Always saying "Sending" is misleading. Tested-by: Robert Baldyga <r.baldyga@samsung.com> Acked-by: John Youn <johnyoun@synopsys.com> Signed-off-by: Mian Yousaf Kaukab <yousaf.kaukab@intel.com> Signed-off-by: Felipe Balbi <balbi@ti.com>
2015-01-30usb: dwc2: gadget: don't modify pullup status during resetGregory Herrero
Pullup doesn't need to be enabled during usb reset since it is already enabled. This leads to shorter chirp-k duration if done during usb reset. Tested-by: Robert Baldyga <r.baldyga@samsung.com> Acked-by: John Youn <johnyoun@synopsys.com> Signed-off-by: Gregory Herrero <gregory.herrero@intel.com> Signed-off-by: Felipe Balbi <balbi@ti.com>
2015-01-30usb: dwc2: gadget: add reset flag in init functionGregory Herrero
Add a flag to request physical reset of the controller when s3c_hsotg_core_init_disconnected is called. During the usb reset, controller must not be fully reconfigured and resetted. Else this leads to shorter chirp-k duration during enumeration. Tested-by: Robert Baldyga <r.baldyga@samsung.com> Acked-by: John Youn <johnyoun@synopsys.com> Signed-off-by: Gregory Herrero <gregory.herrero@intel.com> Signed-off-by: Mian Yousaf Kaukab <yousaf.kaukab@intel.com> Signed-off-by: Felipe Balbi <balbi@ti.com>
2015-01-30usb: dwc2: gadget: add unaligned buffers supportMian Yousaf Kaukab
When using DMA, dwc2 requires buffers to be 4 bytes aligned. Use bounce buffers if they are not. Tested-by: Robert Baldyga <r.baldyga@samsung.com> Acked-by: John Youn <johnyoun@synopsys.com> Signed-off-by: Mian Yousaf Kaukab <yousaf.kaukab@intel.com> Signed-off-by: Felipe Balbi <balbi@ti.com>
2015-01-30usb: dwc2: gadget: remove hardcoded if (0) and if (1) checksMian Yousaf Kaukab
Remove dead code as well. Tested-by: Robert Baldyga <r.baldyga@samsung.com> Acked-by: John Youn <johnyoun@synopsys.com> Signed-off-by: Mian Yousaf Kaukab <yousaf.kaukab@intel.com> Signed-off-by: Felipe Balbi <balbi@ti.com>
2015-01-30usb: dwc2: gadget: fix a typo in commentGregory Herrero
s3c_hsotg_process_req_feature comments was not correct Tested-by: Robert Baldyga <r.baldyga@samsung.com> Acked-by: John Youn <johnyoun@synopsys.com> Signed-off-by: Gregory Herrero <gregory.herrero@intel.com> Signed-off-by: Felipe Balbi <balbi@ti.com>
2015-01-30usb: dwc2: gadget: add TEST_MODE feature supportGregory Herrero
Handle SET_FEATURE TEST_MODE request sent by the host. Slightly rework FEATURE request handling to allow parsing other request types than Endpoint. Also add a debugfs to change test mode value from user space. Tested-by: Robert Baldyga <r.baldyga@samsung.com> Acked-by: John Youn <johnyoun@synopsys.com> Signed-off-by: Gregory Herrero <gregory.herrero@intel.com> Signed-off-by: Felipe Balbi <balbi@ti.com>
2015-01-30usb: dwc2: gadget: fix clear halt feature handlingGregory Herrero
When clearing HALT on an endpoint, req->complete of in progress requests must be called with locks off. New request should only be started if there is not already a pending request on the endpoint. Tested-by: Robert Baldyga <r.baldyga@samsung.com> Acked-by: John Youn <johnyoun@synopsys.com> Signed-off-by: Gregory Herrero <gregory.herrero@intel.com> Signed-off-by: Felipe Balbi <balbi@ti.com>
2015-01-19Merge tag 'v3.19-rc5' into nextFelipe Balbi
Linux 3.19-rc5 Conflicts: drivers/usb/dwc2/gadget.c drivers/usb/gadget/udc/bdc/bdc_ep.c
2015-01-12usb: dwc2: gadget: report disconnection after resetMian Yousaf Kaukab
If usb bus is reset without a physical disconnection, all endpoints will remain open. Call s3c_hsotg_disconnect() from reset handler to report a disconnect to gadget framework. hsotg->connected is checked in s3c_hsotg_disconnect() before processing disconnect. In some cases, USBRst is seen before EnumDone and after it as well. So move setting of hsotg->connected to set-address to avoid reporting extra disconnection in this case. Tested-by: Robert Baldyga <r.baldyga@samsung.com> Acked-by: Paul Zimmerman <paulz@synopsys.com> Signed-off-by: Mian Yousaf Kaukab <yousaf.kaukab@intel.com> Signed-off-by: Felipe Balbi <balbi@ti.com>
2015-01-12usb: dwc2: gadget: force gadget initialization in dev modeGregory Herrero
When booting with id pin grounded, dwc2 default to host mode. Thus, force device mode prior initializing gadget part. Else fifo init will fail since fifo values are not correct in host mode. Tested-by: Robert Baldyga <r.baldyga@samsung.com> Acked-by: Paul Zimmerman <paulz@synopsys.com> Signed-off-by: Gregory Herrero <gregory.herrero@intel.com> Signed-off-by: Felipe Balbi <balbi@ti.com>
2015-01-12usb: dwc2: gadget: add vbus_draw supportGregory Herrero
This callback informs the driver about the total amount of current it is allowed to draw. Share this information with the phy so that current limits can be set for charging for example. Tested-by: Robert Baldyga <r.baldyga@samsung.com> Acked-by: Paul Zimmerman <paulz@synopsys.com> Signed-off-by: Gregory Herrero <gregory.herrero@intel.com> Signed-off-by: Felipe Balbi <balbi@ti.com>
2015-01-12usb: dwc2: gadget: fix pullup handlingGregory Herrero
Gadget must be informed about disconnection when pullup is removed. Tested-by: Robert Baldyga <r.baldyga@samsung.com> Acked-by: Paul Zimmerman <paulz@synopsys.com> Signed-off-by: Gregory Herrero <gregory.herrero@intel.com> Signed-off-by: Felipe Balbi <balbi@ti.com>
2015-01-12usb: dwc2: gadget: reset fifo_map when initializing fifosGregory Herrero
After all endpoints are disabled, fifo_map should have reached 0. Its a bug if if didn't, so warn about it and reset it to 0 so that driver can continue using all the fifos. Tested-by: Robert Baldyga <r.baldyga@samsung.com> Acked-by: Paul Zimmerman <paulz@synopsys.com> Signed-off-by: Gregory Herrero <gregory.herrero@intel.com> Signed-off-by: Mian Yousaf Kaukab <yousaf.kaukab@intel.com> Signed-off-by: Felipe Balbi <balbi@ti.com>
2015-01-12usb: dwc2: gadget: fix fifo allocation leakMian Yousaf Kaukab
When selecting different alt setting, s3c_hsotg_ep_enable can be called with fifo already allocated. Allocate fifo again only if required and after deallocating the previous fifo. Tested-by: Robert Baldyga <r.baldyga@samsung.com> Acked-by: Paul Zimmerman <paulz@synopsys.com> Signed-off-by: Mian Yousaf Kaukab <yousaf.kaukab@intel.com> Signed-off-by: Felipe Balbi <balbi@ti.com>
2015-01-12usb: dwc2: gadget: pick smallest acceptable fifoMian Yousaf Kaukab
Current algorithm picks the first fifo which is equal to or greater than the required size. This can result in bigger fifos assigned to endpoints with smaller maxps. Change the algorithm to pick the smallest fifo which is greater than or equal to the required size. Moreover, only use signed variables when required. Tested-by: Robert Baldyga <r.baldyga@samsung.com> Acked-by: Paul Zimmerman <paulz@synopsys.com> Signed-off-by: Mian Yousaf Kaukab <yousaf.kaukab@intel.com> Signed-off-by: Felipe Balbi <balbi@ti.com>
2015-01-12usb: dwc2: gadget: rename sent_zlp to send_zlpMian Yousaf Kaukab
This flag is set before sending the zlp. So use present tense instead of the past tense. Tested-by: Robert Baldyga <r.baldyga@samsung.com> Acked-by: Paul Zimmerman <paulz@synopsys.com> Signed-off-by: Mian Yousaf Kaukab <yousaf.kaukab@intel.com> Signed-off-by: Felipe Balbi <balbi@ti.com>
2015-01-12usb: dwc2: gadget: add vbus_session supportGregory Herrero
Enable phy driver to report vbus session. This allows us to remove D+ pullup when vbus is not present. Tested-by: Robert Baldyga <r.baldyga@samsung.com> Acked-by: Paul Zimmerman <paulz@synopsys.com> Signed-off-by: Gregory Herrero <gregory.herrero@intel.com> Signed-off-by: Mian Yousaf Kaukab <yousaf.kaukab@intel.com> Signed-off-by: Felipe Balbi <balbi@ti.com>
2015-01-12usb: dwc2: gadget: don't block after fifo flush timeoutGregory Herrero
Can't stay in the loop forever. Break it after timeout. Tested-by: Robert Baldyga <r.baldyga@samsung.com> Acked-by: Paul Zimmerman <paulz@synopsys.com> Signed-off-by: Gregory Herrero <gregory.herrero@intel.com> Signed-off-by: Felipe Balbi <balbi@ti.com>
2015-01-12usb: dwc2: gadget: dont warn if endpoint is not enabledMian Yousaf Kaukab
The warning is probably good but it has false positives in both dma and non-dma cases. So its not very helpful in either. Tested-by: Robert Baldyga <r.baldyga@samsung.com> Acked-by: Paul Zimmerman <paulz@synopsys.com> Signed-off-by: Mian Yousaf Kaukab <yousaf.kaukab@intel.com> Signed-off-by: Felipe Balbi <balbi@ti.com>
2015-01-12usb: dwc2: gadget: fix zero length packet transfersMian Yousaf Kaukab
According to programming guide, zero length packet should be programmed on its own and should not be counted in DIEPTSIZ.PktCnt with other packets. For ep0, this is the zlp for DATA IN stage (if required) and not for the STATUS stage. Tested-by: Robert Baldyga <r.baldyga@samsung.com> Acked-by: Paul Zimmerman <paulz@synopsys.com> Signed-off-by: Gregory Herrero <gregory.herrero@intel.com> Signed-off-by: Mian Yousaf Kaukab <yousaf.kaukab@intel.com> Signed-off-by: Felipe Balbi <balbi@ti.com>
2015-01-12usb: dwc2: gadget: manage ep0 state in softwareMian Yousaf Kaukab
Manage ep0 state in software to add handling of status OUT stage. Just toggling hsotg->setup in s3c_hsotg_handle_outdone leaves it in wrong state in 2-stage control transfers. Moreover, ensure that for setup-packet s3c_hsotg_handle_outdone is called either from SetupDone or OutDone but not both. Dwc2 ip v3.00a generates both SetupDone and OutDone on setup packets. Tested-by: Robert Baldyga <r.baldyga@samsung.com> Acked-by: Paul Zimmerman <paulz@synopsys.com> Signed-off-by: Mian Yousaf Kaukab <yousaf.kaukab@intel.com> Signed-off-by: Felipe Balbi <balbi@ti.com>
2015-01-12usb: dwc2: gadget: kill requests after disabling epMian Yousaf Kaukab
kill_all_requests() can flush the fifo. Call it after disabling the endpoint. Tested-by: Robert Baldyga <r.baldyga@samsung.com> Acked-by: Paul Zimmerman <paulz@synopsys.com> Signed-off-by: Mian Yousaf Kaukab <yousaf.kaukab@intel.com> Signed-off-by: Felipe Balbi <balbi@ti.com>
2015-01-12usb: dwc2: gadget: consider all tx fifosMian Yousaf Kaukab
When matching tx fifo to endpoint, consider all fifos instead of hard limiting to 8 Moreover, print error in case no fifo could be found. Tested-by: Robert Baldyga <r.baldyga@samsung.com> Acked-by: Paul Zimmerman <paulz@synopsys.com> Signed-off-by: Mian Yousaf Kaukab <yousaf.kaukab@intel.com> Signed-off-by: Felipe Balbi <balbi@ti.com>
2015-01-12usb: dwc2: gadget: fix debug loop limitsMian Yousaf Kaukab
< 15 check doesn't show debug information for endpoint 15. It is possible to have less than 15 endpoints so use limit provided by hardware configuration. Tested-by: Robert Baldyga <r.baldyga@samsung.com> Acked-by: Paul Zimmerman <paulz@synopsys.com> Signed-off-by: Mian Yousaf Kaukab <yousaf.kaukab@intel.com> Signed-off-by: Felipe Balbi <balbi@ti.com>
2015-01-12usb: dwc2: gadget: configure fifos from device treeGregory Herrero
As fifo size can vary between SOCs, add possibility to configure them from device tree. Fifo sizes used by the legacy driver will be used If they are not provided by the device tree. Tested-by: Robert Baldyga <r.baldyga@samsung.com> Acked-by: Paul Zimmerman <paulz@synopsys.com> Signed-off-by: Gregory Herrero <gregory.herrero@intel.com> Signed-off-by: Mian Yousaf Kaukab <yousaf.kaukab@intel.com> Reviewed-by: Robert Baldyga <r.baldyga@samsung.com> Signed-off-by: Felipe Balbi <balbi@ti.com>
2015-01-12usb: dwc2: gadget: check interrupts for all endpointsMian Yousaf Kaukab
Current code does not check endpoint 15 interrupt. Use number of endpoint configured in hardware instead of the hardcoded value. Tested-by: Robert Baldyga <r.baldyga@samsung.com> Acked-by: Paul Zimmerman <paulz@synopsys.com> Signed-off-by: Mian Yousaf Kaukab <yousaf.kaukab@intel.com> Signed-off-by: Felipe Balbi <balbi@ti.com>
2015-01-12usb: dwc2: gadget: add bi-directional endpoint supportMian Yousaf Kaukab
GHWCFG1 provides hardware configuration of each endpoint. Use it to configure the endpoints instead of assuming all even endpoint are OUT and all odd endpoints are IN. Tested-by: Robert Baldyga <r.baldyga@samsung.com> Acked-by: Paul Zimmerman <paulz@synopsys.com> Signed-off-by: Mian Yousaf Kaukab <yousaf.kaukab@intel.com> Signed-off-by: Felipe Balbi <balbi@ti.com>
2015-01-12usb: dwc2: gadget: add device tree property to enable dmaGregory Herrero
* Add an of specific function to parse device node properties. * Enable dma usage only if device tree property 'g_use_dma' is present. Tested-by: Robert Baldyga <r.baldyga@samsung.com> Acked-by: Paul Zimmerman <paulz@synopsys.com> Signed-off-by: Gregory Herrero <gregory.herrero@intel.com> Signed-off-by: Felipe Balbi <balbi@ti.com>
2015-01-12usb: dwc2: gadget: don't erase gahbcfg register when enabling dmaGregory Herrero
Do a read-modify-write instead of only setting DMAEn bit. Tested-by: Robert Baldyga <r.baldyga@samsung.com> Acked-by: Paul Zimmerman <paulz@synopsys.com> Signed-off-by: Gregory Herrero <gregory.herrero@intel.com> Signed-off-by: Felipe Balbi <balbi@ti.com>
2015-01-12usb: dwc2: gadget: write correct value in ahbcfg registerGregory Herrero
HBstLen is GAHBCFG[4:1]. Use GAHBCFG_HBSTLEN_SHIFT to write burst- length at correct position. Tested-by: Robert Baldyga <r.baldyga@samsung.com> Acked-by: Paul Zimmerman <paulz@synopsys.com> Signed-off-by: Gregory Herrero <gregory.herrero@intel.com> Signed-off-by: Felipe Balbi <balbi@ti.com>
2015-01-12usb: dwc2: gadget: fix error path in dwc2_gadget_initMian Yousaf Kaukab
In the error path, s3c_hsotg_phy_disable should be called after a call to s3c_hsotg_phy_enable is made. Tested-by: Robert Baldyga <r.baldyga@samsung.com> Acked-by: Paul Zimmerman <paulz@synopsys.com> Signed-off-by: Mian Yousaf Kaukab <yousaf.kaukab@intel.com> Signed-off-by: Felipe Balbi <balbi@ti.com>
2015-01-12usb: dwc2: gadget: don't embed ep0 buffersMian Yousaf Kaukab
When using DMA, data of the previous setup packet can be read back from cache because ep0 and ctrl buffers are embedded in struct s3c_hsotg. Allocate buffers instead of embedding them. Tested-by: Robert Baldyga <r.baldyga@samsung.com> Acked-by: Paul Zimmerman <paulz@synopsys.com> Signed-off-by: Mian Yousaf Kaukab <yousaf.kaukab@intel.com> Reviewed-by: Robert Baldyga <r.baldyga@samsung.com> Signed-off-by: Felipe Balbi <balbi@ti.com>
2015-01-12usb: dwc2: gadget: don't process XferCompl on setup packetMian Yousaf Kaukab
Only process DOEPINT.XferCompl on data packet as DOEPINTn.SetUp can occur with or without DOEPINT.XferCompl. When DOEPINT.SetUp occurs with DOEPINT.XferCompl, only DOEPINT.SetUp needs to be handled. Moreover, ignore DOEPINT.XferCompl when it occurs with DOEPINT.StupPktRcvd as driver needs to wait for DOEPINT.SetUp to continue. Tested-by: Robert Baldyga <r.baldyga@samsung.com> Acked-by: Paul Zimmerman <paulz@synopsys.com> Signed-off-by: Mian Yousaf Kaukab <yousaf.kaukab@intel.com> Signed-off-by: Felipe Balbi <balbi@ti.com>
2015-01-12usb: dwc2: gadget: mask fifo empty irq with dmaMian Yousaf Kaukab
When using DMA, keep fifo empty interrupt disabled. Otherwise core is flooded by interrupts. Tested-by: Robert Baldyga <r.baldyga@samsung.com> Acked-by: Paul Zimmerman <paulz@synopsys.com> Signed-off-by: Gregory Herrero <gregory.herrero@intel.com> Signed-off-by: Mian Yousaf Kaukab <yousaf.kaukab@intel.com> Signed-off-by: Felipe Balbi <balbi@ti.com>
2015-01-12usb: dwc2: gadget: register gadget handle to the phyGregory Herrero
Bind peripheral controller to the phy on udc_start. Unbind on udc_stop. Tested-by: Robert Baldyga <r.baldyga@samsung.com> Acked-by: Paul Zimmerman <paulz@synopsys.com> Signed-off-by: Gregory Herrero <gregory.herrero@intel.com> Signed-off-by: Mian Yousaf Kaukab <yousaf.kaukab@intel.com> Signed-off-by: Felipe Balbi <balbi@ti.com>
2015-01-12drivers: usb: dwc2: remove 'force' parameter from kill_all_requests()Robert Baldyga
This patch fixes in simpler way the bug described in [1] and [2]. It looks like DWC2 is the only UDC driver that doesn't force usb requests to complete in ep_disable() function. This causes described problem, because we have no guarantee that all requests will be completed before unbind of usb function. To fix this problem we force all requests of disabled endpoint to complete. Also currently running request is not handled. This allowed to simplify code of kill_all_requests() function, because 'force' parameter is always set to true, so we don't need it anymore. In s3c_hsotg_rx_data() we change function used to print message when active request is NULL from dev_warn() to dev_dbg(), because such situation is harmless for driver and now it can take place during normal endpoint disabling. [1] https://lkml.org/lkml/2014/12/9/283 [2] https://lkml.org/lkml/2014/12/12/360 Acked-by: Paul Zimmerman <paulz@synopsys.com> Signed-off-by: Robert Baldyga <r.baldyga@samsung.com> Signed-off-by: Felipe Balbi <balbi@ti.com>
2015-01-12usb: dwc2: platform: add generic PHY framework supportYunzhi Li
Get PHY parameters from devicetree and power off usb PHY during system suspend. Acked-by: Paul Zimmerman <paulz@synopsys.com> Signed-off-by: Yunzhi Li <lyz@rock-chips.com> Signed-off-by: Felipe Balbi <balbi@ti.com>
2015-01-12usb: dwc2: Fixed a few typos in commentsMickael Maison
Fixed 3 typos in comments Signed-off-by: Mickael Maison <mickael.maison@gmail.com> Signed-off-by: Felipe Balbi <balbi@ti.com>
2014-12-22usb: dwc2: gadget: kill requests with 'force' in s3c_hsotg_udc_stop()Robert Baldyga
This makes us sure that all requests are completed before we unbind gadget. There are assumptions in gadget API that all requests have to be completed and leak of complete can break some usb function drivers. For example unbind of ECM function can cause NULL pointer dereference: [ 26.396595] configfs-gadget gadget: unbind function 'cdc_ethernet'/e79c4c00 [ 26.414999] Unable to handle kernel NULL pointer dereference at virtual address 00000000 (...) [ 26.452223] PC is at ecm_unbind+0x6c/0x9c [ 26.456209] LR is at ecm_unbind+0x68/0x9c (...) [ 26.603696] [<c033fdb4>] (ecm_unbind) from [<c033661c>] (purge_configs_funcs+0x94/0xd8) [ 26.611674] [<c033661c>] (purge_configs_funcs) from [<c0336674>] (configfs_composite_unbind+0x14/0x34) [ 26.620961] [<c0336674>] (configfs_composite_unbind) from [<c0337124>] (usb_gadget_remove_driver+0x68/0x9c) [ 26.630683] [<c0337124>] (usb_gadget_remove_driver) from [<c03376c8>] (usb_gadget_unregister_driver+0x64/0x94) [ 26.640664] [<c03376c8>] (usb_gadget_unregister_driver) from [<c0336be8>] (unregister_gadget+0x20/0x3c) [ 26.650038] [<c0336be8>] (unregister_gadget) from [<c0336c84>] (gadget_dev_desc_UDC_store+0x80/0xb8) [ 26.659152] [<c0336c84>] (gadget_dev_desc_UDC_store) from [<c0335120>] (gadget_info_attr_store+0x1c/0x28) [ 26.668703] [<c0335120>] (gadget_info_attr_store) from [<c012135c>] (configfs_write_file+0xe8/0x148) [ 26.677818] [<c012135c>] (configfs_write_file) from [<c00c8dd4>] (vfs_write+0xb0/0x1a0) [ 26.685801] [<c00c8dd4>] (vfs_write) from [<c00c91b8>] (SyS_write+0x44/0x84) [ 26.692834] [<c00c91b8>] (SyS_write) from [<c000e560>] (ret_fast_syscall+0x0/0x30) [ 26.700381] Code: e30409f8 e34c0069 eb07b88d e59430a8 (e5930000) [ 26.706485] ---[ end trace f62a082b323838a2 ]--- It's because in some cases request is still running on endpoint during unbind and kill_all_requests() called from s3c_hsotg_udc_stop() function doesn't cause call of complete() of request. Missing complete() call causes ecm->notify_req equals NULL in ecm_unbind() function, and this is reason of this bug. Similar breaks can be observed in another usb function drivers. This patch fixes this bug forcing usb request completion in when s3c_hsotg_ep_disable() is called from s3c_hsotg_udc_stop(). Acked-by: Paul Zimmerman <paulz@synopsys.com> Signed-off-by: Robert Baldyga <r.baldyga@samsung.com> Signed-off-by: Felipe Balbi <balbi@ti.com>
2014-11-25Merge tag 'usb-for-v3.19' of ↵Greg Kroah-Hartman
git://git.kernel.org/pub/scm/linux/kernel/git/balbi/usb into usb-next Felipe writes: usb: patches for v3.19 merge window This time, a very pull request with 216 non-merge commits. Most of the commits contained here are sparse or coccinelle fixes ranging from missing 'static' to returning 0 in case of errors. More importantly, we have the removal the now unnecessary 'driver' argument to ->udc_stop(). DWC2 learned about Dual-Role builds. Users of this IP can now have a single driver built for host and device roles. DWC3 got support for two new HW platforms: Exynos7 and AMD. The Broadcom USB 3.0 Device Controller IP is now supported and so is PLX USB338x, which means DWC3 has lost is badge as the only USB 3.0 peripheral IP supported on Linux. Thanks for Tony Lindgren's work, we can now have a distro-like kernel where all MUSB glue layers can be built into the same kernel (statically or dynamically linked) and it'll work in PIO (DMA will come probably on v3.20). Other than these, the usual set of cleanups and non-critical fixes. Signed-off-by: Felipe Balbi <balbi@ti.com>
generated by cgit v1.2.3 (git 2.39.1) at 2025-07-31 18:51:06 +0000