summaryrefslogtreecommitdiff
path: root/drivers/usb/dwc2/gadget.c
AgeCommit message (Collapse)Author
2016-06-21usb: dwc2: gadget: Remove unnecessary lineVardan Mikayelyan
Removed "ctrl |= DXEPCTL_USBACTEP" from dwc2_hsotg_start_req() function because this step is done in dwc2_hsotg_ep_enable(). Tested-by: John Keeping <john@metanate.com> Signed-off-by: Vardan Mikayelyan <mvardan@synopsys.com> Signed-off-by: John Youn <johnyoun@synopsys.com> Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
2016-05-31usb: dwc2: gadget: Do not halt isochronous endpointsVahram Aharonyan
Add a check in dwc2_hsotg_ep_sethalt() so that it does not halt isochronous endpoints. Signed-off-by: Vahram Aharonyan <vahrama@synopsys.com> Signed-off-by: John Youn <johnyoun@synopsys.com> Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
2016-05-31usb: dwc2: gadget: Do not halt endpoint if activeVahram Aharonyan
The gadget API function usb_ep_set_halt() expects the gadget to return -EAGAIN if the ep is active. Add support for this behavior. Otherwise this may break mass storage protocol if a STALL is attempted on the endpoint. Signed-off-by: Vahram Aharonyan <vahrama@synopsys.com> Signed-off-by: John Youn <johnyoun@synopsys.com> Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
2016-04-28usb: dwc2: gadget: Prevent handling of host interruptsVardan Mikayelyan
In host slave mode, the core asserts the rxready, txfifoempty interrupts that get serviced in the gadget irq handler. Prevent servicing of these when not in the gadget mode of operation. Signed-off-by: Vardan Mikayelyan <mvardan@synopsys.com> Signed-off-by: John Youn <johnyoun@synopsys.com> Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
2016-04-28usb: dwc2: gadget: Check for ep0 in enableVahram Aharonyan
Replaced the WARN_ON with a check and return of -EINVAL in the dwc2_hsotg_ep_enable function if ep0 is passed in. Signed-off-by: Vahram Aharonyan <vahrama@synopsys.com> Signed-off-by: John Youn <johnyoun@synopsys.com> Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
2016-04-04usb: dwc2: do not override forced dr_mode in gadget setupPrzemek Rudy
The host/device mode set with dr_mode should be kept all the time, not being changed to OTG in gadget setup (by overriding CFGUSB_FORCEDEVMODE and CFGUSB_FORCEHOSTMODE bits). Acked-by: John Youn <johnyoun@synopsys.com> Tested-by: John Youn <johnyoun@synopsys.com> Signed-off-by: Przemek Rudy <prudy1@o2.pl> Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
2016-03-04usb: dwc2: Move register save and restore functionsJohn Youn
Move the register save and restore functions into the host and gadget specific files. Tested-by: Douglas Anderson <dianders@chromium.org> Reviewed-by: Douglas Anderson <dianders@chromium.org> Signed-off-by: John Youn <johnyoun@synopsys.com> Signed-off-by: Felipe Balbi <balbi@kernel.org>
2015-12-22usb: dwc2: gadget: Repair DSTS register decodingMarek Vasut
The "enumspd" field is located in register DSTS[2:1], but the code which checks the bitfield does not shift the value accordingly. This in turn causes incorrect detection of gadget link partner speed in dwc2_hsotg_irq_enumdone() . Shift the value accordingly to fix the problem with speed detection. Acked-by: John Youn <johnyoun@synopsys.com> Signed-off-by: Marek Vasut <marex@denx.de> Cc: Felipe Balbi <balbi@ti.com> Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Cc: John Youn <johnyoun@synopsys.com> Signed-off-by: Felipe Balbi <balbi@ti.com>
2015-12-22usb: dwc2: gadget: Remove call to dwc2_hsotg_init()John Youn
Remove call to dwc2_hsotg_init() from dwc2_gadget_init(). The gadget_init function should not access any device registers because the mode isn't guaranteed here. Also, this is already called elsewhere before anything starts on the gadget so it is not necessary here. Signed-off-by: John Youn <johnyoun@synopsys.com> Signed-off-by: Felipe Balbi <balbi@ti.com>
2015-12-22usb: dwc2: gadget: Replace dwc2_hsotg_corereset()John Youn
The dwc2_core_reset() function exists in the core so use that one instead. Signed-off-by: John Youn <johnyoun@synopsys.com> Signed-off-by: Felipe Balbi <balbi@ti.com>
2015-12-22usb: dwc2: gadget: Use hw params from coreJohn Youn
Use the previously cached hw params in the gadget. This saves a reset and force mode in the gadget initialization during probe and makes getting the hardware parameters consistent between gadget and host. Signed-off-by: John Youn <johnyoun@synopsys.com> Signed-off-by: Felipe Balbi <balbi@ti.com>
2015-12-22usb: dwc2: gadget: don't overwrite DCTL register on NAKEFF interruptsGregory Herrero
When receiving GINTSTS_GINNAKEFF or GINTSTS_GOUTNAKEFF interrupt, DCTL will be overwritten with DCTL_CGOUTNAK or DCTL_CGNPINNAK values. Instead of overwriting it, write only needed bits. It could cause an issue if GINTSTS_GINNAKEFF or GINTSTS_GOUTNAKEFF interrupt is received after dwc2 disabled pullup by writing DCTL_SFTDISCON bit. Pullup will then be re-enabled whereas it should not. Acked-by: John Youn <johnyoun@synopsys.com> Signed-off-by: Gregory Herrero <gregory.herrero@intel.com> Signed-off-by: Felipe Balbi <balbi@ti.com>
2015-12-22usb: dwc2: fix transfer stop programming for out endpointDu, Changbin
To stop an out endpoint, software should set sets the Global OUT NAK, but not the Global Non-periodic IN NAK. This driver bug leads the out-ep failed be in disabled state with below error. dwc2_hsotg_ep_stop_xfr: timeout DOEPCTL.EPDisable Acked-by: John Youn <johnyoun@synopsys.com> Signed-off-by: Du, Changbin <changbin.du@intel.com> Signed-off-by: Felipe Balbi <balbi@ti.com>
2015-10-14usb: dwc2: refactor common low-level hw code to platform.cMarek Szyprowski
DWC2 module on some platforms needs three additional hardware resources: phy controller, clock and power supply. All of them must be enabled/activated to properly initialize and operate. This was initially handled in s3c-hsotg driver, which has been converted to 'gadget' part of dwc2 driver. Unfortunately, not all of this code got moved to common platform code, what resulted in accessing DWC2 registers without enabling low-level hardware resources. This fails for example on Exynos SoCs. This patch moves all the code for managing those resources to common platform.c file and provides convenient wrappers for controlling them. Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com> Acked-by: John Youn <johnyoun@synopsys.com> Tested-by: John Youn <johnyoun@synopsys.com> Signed-off-by: Felipe Balbi <balbi@ti.com>
2015-10-14usb: dwc2: remove no longer needed init_mutexMarek Szyprowski
init_mutex is a leftover from the time, when s3c-hsotg driver did not implement proper pull up/down control and emulated it by enabling enabling/disabling usb phy. Proper pull up/down control has been added by commit 5b9451f8c4fbaf0549139755fb45ff2b57975b7f ("usb: dwc2: gadget: use soft-disconnect udc feature in pullup() method"), so init_muxtex can be removed now to avoid potential deadlocks with other locks. Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com> Acked-by: John Youn <johnyoun@synopsys.com> Tested-by: John Youn <johnyoun@synopsys.com> Signed-off-by: Felipe Balbi <balbi@ti.com>
2015-10-02usb: dwc2: gadget: parity fix in isochronous modeRoman Bacik
USB OTG driver in isochronous mode has to set the parity of the receiving microframe. The parity is set to even by default. This causes problems for an audio gadget, if the host starts transmitting on odd microframes. This fix uses Incomplete Periodic Transfer interrupt to toggle between even and odd parity until the Transfer Complete interrupt is received. Signed-off-by: Roman Bacik <rbacik@broadcom.com> Reviewed-by: Abhinav Ratna <aratna@broadcom.com> Reviewed-by: Srinath Mannam <srinath.mannam@broadcom.com> Signed-off-by: Scott Branden <sbranden@broadcom.com> Signed-off-by: John Youn <johnyoun@synopsys.com> Signed-off-by: Felipe Balbi <balbi@ti.com>
2015-10-01usb: dwc2: remove non-functional clock gatingMarek Szyprowski
During typical gadget operation, dwc2 clock was enabled 3 times: from dwc2_gadget_init(), dwc2_hsotg_udc_start() and dwc2_hsotg_pullup(), and then disabled in s3c_hsotg_pullup(), s3c_hsotg_udc_stop() and dwc2_hsotg_remove(). This really makes no sense, so leave clock control code only in dwc2_gadget_init/remove functions. Tested-by: John Youn <johnyoun@synopsys.com> Acked-by: John Youn <johnyoun@synopsys.com> Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com> Signed-off-by: Felipe Balbi <balbi@ti.com>
2015-10-01usb: dwc2: remove double call to dwc2_hsotg_of_probeMarek Szyprowski
This patch removes doubled call to dwc2_hsotg_of_probe() function. Tested-by: John Youn <johnyoun@synopsys.com> Acked-by: John Youn <johnyoun@synopsys.com> Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com> Signed-off-by: Felipe Balbi <balbi@ti.com>
2015-10-01usb: dwc2: gadget: fix a memory use-after-free bugYunzhi Li
When dwc2_hsotg_handle_unaligned_buf_complete() hs_req->req.buf already destroyed, in dwc2_hsotg_unmap_dma(), it touches hs_req->req.dma again, so dwc2_hsotg_unmap_dma() should be called before dwc2_hsotg_handle_unaligned_buf_complete(). Otherwise, it will cause a bad_page BUG, when allocate this memory page next time. This bug led to the following crash: BUG: Bad page state in process swapper/0 pfn:2bdbc [ 26.820440] page:eed76780 count:0 mapcount:0 mapping: (null) index:0x0 [ 26.854710] page flags: 0x200(arch_1) [ 26.885836] page dumped because: PAGE_FLAGS_CHECK_AT_PREP flag set [ 26.919179] bad because of flags: [ 26.948917] page flags: 0x200(arch_1) [ 26.979100] Modules linked in: [ 27.008401] CPU: 0 PID: 0 Comm: swapper/0 Tainted: G W3.14.0 #17 [ 27.041816] [<c010e1f8>] (unwind_backtrace) from [<c010a704>] (show_stack+0x20/0x24) [ 27.076108] [<c010a704>] (show_stack) from [<c087eea8>] (dump_stack+0x70/0x8c) [ 27.110246] [<c087eea8>] (dump_stack) from [<c01ce0b8>] (bad_page+0xfc/0x12c) [ 27.143958] [<c01ce0b8>] (bad_page) from [<c01ce65c>] (get_page_from_freelist+0x3e4/0x50c) [ 27.179298] [<c01ce65c>] (get_page_from_freelist) from [<c01ce9a0>] (__alloc_pages_nodemask) [ 27.216296] [<c01ce9a0>] (__alloc_pages_nodemask) from [<c01cf00c>] (__get_free_pages+0x20/) [ 27.252326] [<c01cf00c>] (__get_free_pages) from [<c01e5bec>] (kmalloc_order_trace+0x34/0xa) [ 27.288295] [<c01e5bec>] (kmalloc_order_trace) from [<c0203304>] (__kmalloc+0x40/0x1ac) [ 27.323751] [<c0203304>] (__kmalloc) from [<c052abc0>] (dwc2_hsotg_ep_queue.isra.12+0x7c/0x1) [ 27.359937] [<c052abc0>] (dwc2_hsotg_ep_queue.isra.12) from [<c052af88>] (dwc2_hsotg_ep_queue) [ 27.397478] [<c052af88>] (dwc2_hsotg_ep_queue_lock) from [<c0554110>] (rx_submit+0xfc/0x164) [ 27.433619] [<c0554110>] (rx_submit) from [<c05546e8>] (rx_complete+0x22c/0x230) [ 27.468872] [<c05546e8>] (rx_complete) from [<c052b528>] (dwc2_hsotg_complete_request+0xfc/0) [ 27.506240] [<c052b528>] (dwc2_hsotg_complete_request) from [<c052bba0>] (dwc2_hsotg_handle_o) [ 27.545401] [<c052bba0>] (dwc2_hsotg_handle_outdone) from [<c052be70>] (dwc2_hsotg_epint+0x2c) [ 27.583689] [<c052be70>] (dwc2_hsotg_epint) from [<c052c750>] (dwc2_hsotg_irq+0x1dc/0x4ac) [ 27.621041] [<c052c750>] (dwc2_hsotg_irq) from [<c01682e0>] (handle_irq_event_percpu+0x70/0x) [ 27.659066] [<c01682e0>] (handle_irq_event_percpu) from [<c01684ec>] (handle_irq_event+0x4c) [ 27.697322] [<c01684ec>] (handle_irq_event) from [<c016bae0>] (handle_fasteoi_irq+0xc8/0x11) [ 27.735451] [<c016bae0>] (handle_fasteoi_irq) from [<c0167b8c>] (generic_handle_irq+0x30/0x) [ 27.773918] [<c0167b8c>] (generic_handle_irq) from [<c0167ca4>] (__handle_domain_irq+0x84/0) [ 27.812018] [<c0167ca4>] (__handle_domain_irq) from [<c01003b0>] (gic_handle_irq+0x48/0x6c) [ 27.849695] [<c01003b0>] (gic_handle_irq) from [<c010b340>] (__irq_svc+0x40/0x50) [ 27.886907] Exception stack(0xc0d01ee0 to 0xc0d01f28) Acked-by: John Youn <johnyoun@synopsys.com> Tested-by: Heiko Stuebner <heiko@sntech.de> Tested-by: Jeffy Chen <jeffy.chen@rock-chips.com> Signed-off-by: Yunzhi Li <lyz@rock-chips.com> Signed-off-by: Felipe Balbi <balbi@ti.com>
2015-10-01usb: dwc2: gadget: handle reset interrupt before endpoint interruptsMian Yousaf Kaukab
If system is loaded, reset, enum-done and setup interrupts can occur at the same time. Current interrupt handling sequence will handle setup packet's interrupt before handling reset interrupt. Which will break the enumeration process. Correct sequence is to handle reset, enum-done and then any other endpoint interrupts. Signed-off-by: Mian Yousaf Kaukab <yousaf.kaukab@intel.com> Tested-by: Robert Baldyga <r.baldyga@samsung.com> Tested-by: Dinh Nguyen <dinguyen@opensource.altera.com> Tested-by: John Youn <johnyoun@synopsys.com> Acked-by: John Youn <johnyoun@synopsys.com> Signed-off-by: Felipe Balbi <balbi@ti.com>
2015-10-01usb: dwc2: gadget: exit hibernation before power downGregory Herrero
When disconnecting cable, controller will detect a suspend condition and enter partial power down. If vbus_session is called by the phy driver during hibernation, make sure controller exit hibernation before it is accessed. Signed-off-by: Jianqiang Tang <jianqiang.tang@intel.com> Signed-off-by: Gregory Herrero <gregory.herrero@intel.com> Signed-off-by: Mian Yousaf Kaukab <yousaf.kaukab@intel.com> Tested-by: Robert Baldyga <r.baldyga@samsung.com> Tested-by: Dinh Nguyen <dinguyen@opensource.altera.com> Tested-by: John Youn <johnyoun@synopsys.com> Acked-by: John Youn <johnyoun@synopsys.com> Signed-off-by: Felipe Balbi <balbi@ti.com>
2015-10-01usb: dwc2: gadget: unmask idstschng interrupt only if controller supports itGregory Herrero
idstschng interrupt should not be used when id pin control is external. This is already handled on dwc2 host part. Fix it on gadget part as well. Signed-off-by: Gregory Herrero <gregory.herrero@intel.com> Signed-off-by: Mian Yousaf Kaukab <yousaf.kaukab@intel.com> Tested-by: Robert Baldyga <r.baldyga@samsung.com> Tested-by: Dinh Nguyen <dinguyen@opensource.altera.com> Tested-by: John Youn <johnyoun@synopsys.com> Acked-by: John Youn <johnyoun@synopsys.com> Signed-off-by: Felipe Balbi <balbi@ti.com>
2015-10-01usb: dwc2: gadget: only reset core after addressed stateMian Yousaf Kaukab
There is a 200ms guard period to avoid unnecessary resets of the dwc2 ip. This delay sometimes prove to be too large when usbcv is run with an ehci host. dwc2 only needs to be reset after addressed state. Change the logic to reset ip after addressed state. Signed-off-by: Mian Yousaf Kaukab <yousaf.kaukab@intel.com> Tested-by: Robert Baldyga <r.baldyga@samsung.com> Tested-by: Dinh Nguyen <dinguyen@opensource.altera.com> Tested-by: John Youn <johnyoun@synopsys.com> Acked-by: John Youn <johnyoun@synopsys.com> Signed-off-by: Felipe Balbi <balbi@ti.com>
2015-10-01usb: dwc2: gadget: kill ep0 requests before reinitializing coreMian Yousaf Kaukab
Make sure there are no requests pending on ep0 before reinitializing core. Otherwise, dwc2_hsotg_enqueue_setup will fail afterwards. Also, take hsotg->lock before calling dwc2_hsotg_core_init_disconnected() from dwc2_conn_id_status_change() as dwc2_hsotg_complete_request() expect lock to be held. Signed-off-by: Mian Yousaf Kaukab <yousaf.kaukab@intel.com> Tested-by: Robert Baldyga <r.baldyga@samsung.com> Tested-by: Dinh Nguyen <dinguyen@opensource.altera.com> Tested-by: John Youn <johnyoun@synopsys.com> Acked-by: John Youn <johnyoun@synopsys.com> Signed-off-by: Felipe Balbi <balbi@ti.com>
2015-10-01usb: dwc2: gadget: stop current transfer on dequeueMian Yousaf Kaukab
If the request being dequeued is already started, disable endpoint to stop the transfer and then call dwc2_hsotg_complete_request(). Endpoint will be re-enabled on next call to dwc2_hsotg_start_req(). Signed-off-by: Mian Yousaf Kaukab <yousaf.kaukab@intel.com> Tested-by: Robert Baldyga <r.baldyga@samsung.com> Tested-by: Dinh Nguyen <dinguyen@opensource.altera.com> Tested-by: John Youn <johnyoun@synopsys.com> Acked-by: John Youn <johnyoun@synopsys.com> Signed-off-by: Felipe Balbi <balbi@ti.com>
2015-10-01usb: dwc2: gadget: print complete setup packetMian Yousaf Kaukab
wIndex field was missing. Also print in natural order instead of Req first, so that its easier to compare for example against bus analyzer logs. Signed-off-by: Mian Yousaf Kaukab <yousaf.kaukab@intel.com> Tested-by: Robert Baldyga <r.baldyga@samsung.com> Tested-by: Dinh Nguyen <dinguyen@opensource.altera.com> Tested-by: John Youn <johnyoun@synopsys.com> Acked-by: John Youn <johnyoun@synopsys.com> Signed-off-by: Felipe Balbi <balbi@ti.com>
2015-10-01usb: dwc2: gadget: ignore stall check for ep0Mian Yousaf Kaukab
dwc2_hsotg_start_req starts a request only if endpoint is not stalled. Ignore this check for ep0 as core will clear DOEPCTL0.Stall after sending stall handshake. Prepare instead for receiving next setup packet. Signed-off-by: Mian Yousaf Kaukab <yousaf.kaukab@intel.com> Tested-by: Robert Baldyga <r.baldyga@samsung.com> Tested-by: Dinh Nguyen <dinguyen@opensource.altera.com> Tested-by: John Youn <johnyoun@synopsys.com> Acked-by: John Youn <johnyoun@synopsys.com> Signed-off-by: Felipe Balbi <balbi@ti.com>
2015-10-01usb: dwc2: gadget: abort core init if core_reset failsGregory Herrero
No point of continue with initialization if core is not in a sane state. Signed-off-by: Gregory Herrero <gregory.herrero@intel.com> Signed-off-by: Mian Yousaf Kaukab <yousaf.kaukab@intel.com> Tested-by: Robert Baldyga <r.baldyga@samsung.com> Tested-by: Dinh Nguyen <dinguyen@opensource.altera.com> Tested-by: John Youn <johnyoun@synopsys.com> Acked-by: John Youn <johnyoun@synopsys.com> Signed-off-by: Felipe Balbi <balbi@ti.com>
2015-10-01usb: dwc2: gadget: set op_state in vbus_session callGregory Herrero
Some device may have external id pin control enabled, so op_state will not be set on id pin interrupt change. Thus, ensure op_state is set to peripheral during vbus detection. Signed-off-by: Gregory Herrero <gregory.herrero@intel.com> Signed-off-by: Mian Yousaf Kaukab <yousaf.kaukab@intel.com> Tested-by: Robert Baldyga <r.baldyga@samsung.com> Tested-by: Dinh Nguyen <dinguyen@opensource.altera.com> Tested-by: John Youn <johnyoun@synopsys.com> Acked-by: John Youn <johnyoun@synopsys.com> Signed-off-by: Felipe Balbi <balbi@ti.com>
2015-10-01usb: dwc2: gadget: don't modify pullup state in host modeGregory Herrero
Modifying the pullup state during host mode trig a new enumeration of attached device. Thus, avoid modifying pullup in host mode. Signed-off-by: Gregory Herrero <gregory.herrero@intel.com> Signed-off-by: Mian Yousaf Kaukab <yousaf.kaukab@intel.com> Tested-by: Robert Baldyga <r.baldyga@samsung.com> Tested-by: Dinh Nguyen <dinguyen@opensource.altera.com> Tested-by: John Youn <johnyoun@synopsys.com> Acked-by: John Youn <johnyoun@synopsys.com> Signed-off-by: Felipe Balbi <balbi@ti.com>
2015-10-01usb: dwc2: gadget: initialize op_state for peripheral only configurationMian Yousaf Kaukab
ID status change interrupt will not be handled in peripheral only configuration. So initialize op_state during gadget init. Signed-off-by: Mian Yousaf Kaukab <yousaf.kaukab@intel.com> Tested-by: Robert Baldyga <r.baldyga@samsung.com> Tested-by: Dinh Nguyen <dinguyen@opensource.altera.com> Tested-by: John Youn <johnyoun@synopsys.com> Acked-by: John Youn <johnyoun@synopsys.com> Signed-off-by: Felipe Balbi <balbi@ti.com>
2015-10-01usb: dwc2: gadget: ensure lx_state corresponds to current stateGregory Herrero
Correctly update lx_state on gadget connection and disconnection. When usb cable is disconnected, lx_state must be updated to L3 as controller could be in power off state. When usb cable is connected, lx_state must be updated to L0 as controller is powered. Signed-off-by: Gregory Herrero <gregory.herrero@intel.com> Signed-off-by: Mian Yousaf Kaukab <yousaf.kaukab@intel.com> Tested-by: Robert Baldyga <r.baldyga@samsung.com> Tested-by: Dinh Nguyen <dinguyen@opensource.altera.com> Tested-by: John Youn <johnyoun@synopsys.com> Acked-by: John Youn <johnyoun@synopsys.com> Signed-off-by: Felipe Balbi <balbi@ti.com>
2015-09-27usb: dwc2: Use platform endianness when accessing registersAntti Seppälä
This patch switches calls to readl/writel to their dwc2_readl/dwc2_writel equivalents which preserve platform endianness. This patch is necessary to access dwc2 registers correctly on big-endian systems such as the mips based SoCs made by Lantiq. Then dwc2 can be used to replace ifx-hcd driver for Lantiq platforms found e.g. in OpenWrt. The patch was autogenerated with the following commands: $EDITOR core.h sed -i "s/\<readl\>/dwc2_readl/g" *.c hcd.h hw.h sed -i "s/\<writel\>/dwc2_writel/g" *.c hcd.h hw.h Some files were then hand-edited to fix checkpatch.pl warnings about too long lines. Signed-off-by: Antti Seppälä <a.seppala@gmail.com> Signed-off-by: Vincent Pelletier <plr.vincent@gmail.com> Signed-off-by: John Youn <johnyoun@synopsys.com> Signed-off-by: Felipe Balbi <balbi@ti.com>
2015-09-27usb: dwc2: rename all s3c_* to dwc2_*Felipe Balbi
this driver has long ago became dwc2.ko with both peripheral and host roles, there's no point in keeping the old function names. Acked-by: John Youn <johnyoun@synopsys.com> Tested-by: John Youn <johnyoun@synopsys.com> Signed-off-by: Felipe Balbi <balbi@ti.com>
2015-08-04usb: dwc2: gadget: add ep capabilities supportRobert Baldyga
Convert endpoint configuration to new capabilities model. Signed-off-by: Robert Baldyga <r.baldyga@samsung.com> Signed-off-by: Felipe Balbi <balbi@ti.com>
2015-07-29usb: dwc2: gadget: use | instead of + for bitmasksFelipe Balbi
It's just a lot clearer to use | operator instead of + operator. Caught by coccicheck: " drivers/usb/dwc2/gadget.c:2883:26-27: WARNING: sum of probable bitmasks, consider | " Cc: John Youn <John.Youn@synopsys.com> Signed-off-by: Felipe Balbi <balbi@ti.com>
2015-04-29usb: dwc2: remove dwc2_platform.koMian Yousaf Kaukab
As dwc2 pci module is now exporting dwc2 platform device, include platform.o in dwc2-y and remove USB_DWC2_PLATFORM configuration option. Driver will be built as two modules, dwc2.ko and dwc2_pci.ko. dwc2.ko is the new platform driver. Remove all EXPORT_SYMBOL_GPL as they are not needed any more. Acked-by: John Youn <johnyoun@synopsys.com> Signed-off-by: Mian Yousaf Kaukab <yousaf.kaukab@intel.com> Signed-off-by: Felipe Balbi <balbi@ti.com>
2015-04-29usb: dwc2: gadget: remove s3c_hsotg_ep_disable_forceMian Yousaf Kaukab
Force argument is not used anymore. Clean up leftovers from https://lkml.org/lkml/2014/12/9/283 Acked-by: John Youn <johnyoun@synopsys.com> Signed-off-by: Mian Yousaf Kaukab <yousaf.kaukab@intel.com> Signed-off-by: Felipe Balbi <balbi@ti.com>
2015-04-29usb: dwc2: gadget: enable otg flag in dual role configurationGregory Herrero
Inform that device is otg-capable in case of otg configuration. Acked-by: John Youn <johnyoun@synopsys.com> Signed-off-by: Gregory Herrero <gregory.herrero@intel.com> Signed-off-by: Felipe Balbi <balbi@ti.com>
2015-04-29usb: dwc2: gadget: powerup controller if neededGregory Herrero
During vbus session, usb controller needs to exit hibernation if it was previously in suspend state. Since controller will be resetted and configured, there is no need to restore registers. Moreover, set lx_state to L0 on B session. vbus_session callback may not be used by all platforms. Thus, controller software state needs to be set to L0 if the controller detects a valid B session. Otherwise, lx_state will remain L2 and prevent any request submission. Acked-by: John Youn <johnyoun@synopsys.com> Signed-off-by: Gregory Herrero <gregory.herrero@intel.com> Signed-off-by: Felipe Balbi <balbi@ti.com>
2015-04-29usb: dwc2: gadget: prevent new request submission during suspendGregory Herrero
If usb controller is in partial power down, any write to registers may cause unpredictable behavior. Thus, prevent any new request submission once controller is in partial power down. Acked-by: John Youn <johnyoun@synopsys.com> Signed-off-by: Gregory Herrero <gregory.herrero@intel.com> Signed-off-by: Felipe Balbi <balbi@ti.com>
2015-04-29usb: dwc2: gadget: ignore pm suspend/resume in L2Gregory Herrero
Nothing to be done in pm suspend/resume when controller is in L2. Don't disconnect or reset. State is already saved when putting controller in hibernation and will be restored on USB bus resume. Acked-by: John Youn <johnyoun@synopsys.com> Signed-off-by: Gregory Herrero <gregory.herrero@intel.com> Signed-off-by: Felipe Balbi <balbi@ti.com>
2015-04-29usb: dwc2: gadget: use reset detect interruptGregory Herrero
ResetDet interrupt is used to detect a reset of the bus while the controller is suspended. This may happens for example when using Command Verifier. Acked-by: John Youn <johnyoun@synopsys.com> Signed-off-by: Gregory Herrero <gregory.herrero@intel.com> Signed-off-by: Felipe Balbi <balbi@ti.com>
2015-04-29usb: dwc2: move debugfs code to a separate fileMian Yousaf Kaukab
Prepare to add more debug code. Moreover, don't save dentry * for each file in struct dwc2_hsotg as clean up is done with debugfs_remove_recursive(). s3c_hsotg_delete_debug() is removed altogether for the same reason. Acked-by: John Youn <johnyoun@synopsys.com> Signed-off-by: Mian Yousaf Kaukab <yousaf.kaukab@intel.com> Signed-off-by: Felipe Balbi <balbi@ti.com>
2015-02-04usb: dwc2: Fix a bug in reading the endpoint directions from reg.Roshan Pius
According to the DWC2 datasheet, the HWCFG1 register stores the configured endpoint directions for endpoints 0-15 in bit positions 0-31. ========================== Endpoint Direction (EpDir) This 32-bit field uses two bits per endpoint to determine the endpoint direction. Endpoint Bits [31:30]: Endpoint 15 direction Bits [29:28]: Endpoint 14 direction .... Bits [3:2]: Endpoint 1 direction Bits[1:0]: Endpoint 0 direction (always BIDIR) ========================== The DWC2 driver is currently interpreting the contents of the register as directions for endpoints 1-15 which leads to an error in determining the configured endpoint directions in the core because the first 2 bits determine the direction of endpoint 0 and not 1. This is based on testing/next branch in Felipe's git. Signed-off-by: Roshan Pius <rpius@chromium.org> Acked-by: John Youn <johnyoun@synopsys.com> Signed-off-by: Felipe Balbi <balbi@ti.com>
2015-01-30usb: dwc2: gadget: initialize controller in pullup callbackGregory Herrero
USB reset interrupt is no more used to reset the controller. Thus, reset the controller in pullup callback as described by Synopsys programming guide. Otherwise enumeration sometimes fails when usb configuration is switched without physical disconnection. Tested-by: Robert Baldyga <r.baldyga@samsung.com> Acked-by: John Youn <johnyoun@synopsys.com> Signed-off-by: Gregory Herrero <gregory.herrero@intel.com> Signed-off-by: Felipe Balbi <balbi@ti.com>
2015-01-30usb: dwc2: gadget: replace constants with definesMian Yousaf Kaukab
Defines are more readable and searchable than constants. Tested-by: Robert Baldyga <r.baldyga@samsung.com> Acked-by: John Youn <johnyoun@synopsys.com> Signed-off-by: Mian Yousaf Kaukab <yousaf.kaukab@intel.com> Signed-off-by: Felipe Balbi <balbi@ti.com>
2015-01-30usb: dwc2: gadget: fix phy interface configurationMian Yousaf Kaukab
hsotg->phyif is set in dwc2_gadget_init according to phy interface width. Use it for configuration instead of hardcoded value. Moreover, set USB turnaround time according to phy width. Tested-by: Robert Baldyga <r.baldyga@samsung.com> Acked-by: John Youn <johnyoun@synopsys.com> Signed-off-by: Mian Yousaf Kaukab <yousaf.kaukab@intel.com> Signed-off-by: Felipe Balbi <balbi@ti.com>
2015-01-30usb: dwc2: gadget: fix debug message for zlpMian Yousaf Kaukab
Print debug message according to zlp direction. Always saying "Sending" is misleading. Tested-by: Robert Baldyga <r.baldyga@samsung.com> Acked-by: John Youn <johnyoun@synopsys.com> Signed-off-by: Mian Yousaf Kaukab <yousaf.kaukab@intel.com> Signed-off-by: Felipe Balbi <balbi@ti.com>
2015-01-30usb: dwc2: gadget: don't modify pullup status during resetGregory Herrero
Pullup doesn't need to be enabled during usb reset since it is already enabled. This leads to shorter chirp-k duration if done during usb reset. Tested-by: Robert Baldyga <r.baldyga@samsung.com> Acked-by: John Youn <johnyoun@synopsys.com> Signed-off-by: Gregory Herrero <gregory.herrero@intel.com> Signed-off-by: Felipe Balbi <balbi@ti.com>
generated by cgit v1.2.3 (git 2.39.1) at 2025-08-03 00:12:32 +0000