| Age | Commit message (Collapse) | Author |
|---|
|
commit a26503092c75abba70a0be2aa01145ecf90c2a22 upstream.
When flushing transmit side DMA, it is the transmit channel that should
be terminated, not the receive channel.
Fixes: 9e512eaaf8f40 ("serial: 8250: Fix fifo underflow on flush")
Cc: stable <stable@kernel.org>
Reported-by: Wentao Guan <guanwentao@uniontech.com>
Signed-off-by: John Keeping <jkeeping@inmusicbrands.com>
Reviewed-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Link: https://lore.kernel.org/r/20250224121831.1429323-1-jkeeping@inmusicbrands.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 2790ce23951f0c497810c44ad60a126a59c8d84c upstream.
If stm32_usart_start_tx is called with an empty xmit buffer, RTS GPIO
could be deasserted prematurely, as bytes in TX FIFO are still
transmitting.
So this patch remove rts disable when xmit buffer is empty.
Fixes: d7c76716169d ("serial: stm32: Use TC interrupt to deassert GPIO RTS in RS485 mode")
Cc: stable <stable@kernel.org>
Signed-off-by: Cheick Traore <cheick.traore@foss.st.com>
Link: https://lore.kernel.org/r/20250320152540.709091-1-cheick.traore@foss.st.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
registers
commit f5cb528d6441eb860250a2f085773aac4f44085e upstream.
According to the LPUART reference manual, TXRTSE and TXRTSPOL of MODIR
register only can be changed when the transmitter is disabled.
So disable the transmitter before changing RS485 related registers and
re-enable it after the change is done.
Fixes: 67b01837861c ("tty: serial: lpuart: Add RS485 support for 32-bit uart flavour")
Cc: stable <stable@kernel.org>
Signed-off-by: Sherry Sun <sherry.sun@nxp.com>
Reviewed-by: Frank Li <Frank.Li@nxp.com>
Link: https://lore.kernel.org/r/20250312022503.1342990-1-sherry.sun@nxp.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 5c7e2896481a177bbda41d7850f05a9f5a8aee2b upstream.
These ExpressCard devices use the OxPCIE chip and can be used with
this driver.
Signed-off-by: Cameron Williams <cang1@live.co.uk>
Cc: stable <stable@kernel.org>
Link: https://lore.kernel.org/r/DB7PR02MB3802907A9360F27F6CD67AAFC4D62@DB7PR02MB3802.eurprd02.prod.outlook.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit be6a23650908e2f827f2e7839a3fbae41ccb5b63 upstream.
These card IDs got missed the first time around.
Cc: stable <stable@kernel.org>
Signed-off-by: Cameron Williams <cang1@live.co.uk>
Link: https://lore.kernel.org/r/DB7PR02MB380295BCC879CCF91315AC38C4C12@DB7PR02MB3802.eurprd02.prod.outlook.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 9e512eaaf8f4008c44ede3dfc0fbc9d9c5118583 upstream.
When flushing the serial port's buffer, uart_flush_buffer() calls
kfifo_reset() but if there is an outstanding DMA transfer then the
completion function will consume data from the kfifo via
uart_xmit_advance(), underflowing and leading to ongoing DMA as the
driver tries to transmit another 2^32 bytes.
This is readily reproduced with serial-generic and amidi sending even
short messages as closing the device on exit will wait for the fifo to
drain and in the underflow case amidi hangs for 30 seconds on exit in
tty_wait_until_sent(). A trace of that gives:
kworker/1:1-84 [001] 51.769423: bprint: serial8250_tx_dma: tx_size=3 fifo_len=3
amidi-763 [001] 51.769460: bprint: uart_flush_buffer: resetting fifo
irq/21-fe530000-76 [000] 51.769474: bprint: __dma_tx_complete: tx_size=3
irq/21-fe530000-76 [000] 51.769479: bprint: serial8250_tx_dma: tx_size=4096 fifo_len=4294967293
irq/21-fe530000-76 [000] 51.781295: bprint: __dma_tx_complete: tx_size=4096
irq/21-fe530000-76 [000] 51.781301: bprint: serial8250_tx_dma: tx_size=4096 fifo_len=4294963197
irq/21-fe530000-76 [000] 51.793131: bprint: __dma_tx_complete: tx_size=4096
irq/21-fe530000-76 [000] 51.793135: bprint: serial8250_tx_dma: tx_size=4096 fifo_len=4294959101
irq/21-fe530000-76 [000] 51.804949: bprint: __dma_tx_complete: tx_size=4096
Since the port lock is held in when the kfifo is reset in
uart_flush_buffer() and in __dma_tx_complete(), adding a flush_buffer
hook to adjust the outstanding DMA byte count is sufficient to avoid the
kfifo underflow.
Fixes: 9ee4b83e51f74 ("serial: 8250: Add support for dmaengine")
Cc: stable <stable@kernel.org>
Signed-off-by: John Keeping <jkeeping@inmusicbrands.com>
Link: https://lore.kernel.org/r/20250208124148.1189191-1-jkeeping@inmusicbrands.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit e8486bd50ecf63c9a1e25271f258a8d959f2672f upstream.
The documentation of the __uart_read_properties() states that
->iotype member is always altered after the function call, but
the code doesn't do that in the case when use_defaults == false
and the value of reg-io-width is unsupported. Make sure the code
follows the documentation.
Note, the current users of the uart_read_and_validate_port_properties()
will fail and the change doesn't affect their behaviour, neither
users of uart_read_port_properties() will be affected since the
alteration happens there even in the current code flow.
Fixes: e894b6005dce ("serial: port: Introduce a common helper to read properties")
Cc: stable <stable@kernel.org>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20250124161530.398361-3-andriy.shevchenko@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 166ac2bba167d575e7146beaa66093bc7c072f43 upstream.
Currently the ->iotype is always assigned to the UPIO_MEM when
the respective property is not found. However, this will not
support the cases when user wants to have UPIO_PORT to be set
or preserved. Support this scenario by checking ->iobase value
and default the ->iotype respectively.
Fixes: 1117a6fdc7c1 ("serial: 8250_of: Switch to use uart_read_port_properties()")
Fixes: e894b6005dce ("serial: port: Introduce a common helper to read properties")
Cc: stable <stable@kernel.org>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20250124161530.398361-2-andriy.shevchenko@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit e95cb63e57381f00d9274533ea7fd0ac3bf4e5b0 ]
In the B0 revision, the RTS pin remains high due to incorrect hardware
mapping. To address this issue, enable auto-direction control with the
RTS bit in ADCL_CFG_REG. This configuration ensures that the RTS pin
goes low when the terminal is opened and high when the terminal is
closed. Additionally, we reset the step counter for Rx and Tx engines
by writing into FRAC_DIV_CFG_REG.
Signed-off-by: Rengarajan S <rengarajan.s@microchip.com>
Link: https://lore.kernel.org/r/20241218094017.18290-1-rengarajan.s@microchip.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 535a07698b8b3e6f305673102d297262cae2360a ]
parport_serial driver uses subset of WCH IDs that are present in 8250_pci.
Share them via pci_ids.h and switch parport_serial to use defined constants.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20241204031114.1029882-3-andriy.shevchenko@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 16076ca3a1565491bcb28689e555d569a39391c7 ]
There are two sites of the same brand: wch.cn and wch-ic.com.
They are property of the same company, but it appears that they
managed to get two different PCI vendor IDs. Rename them accordingly
using standard pattern, i.e. PCI_VENDOR_ID_...
While at it, move to PCI_VDEVICE() in the ID tables.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20241204031114.1029882-2-andriy.shevchenko@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
in use
commit 9f7dea875cc7f9c1a56a5c688290634a59cd1420 upstream.
In the sh-sci driver, sci_ports[0] is used by earlycon. If the earlycon is
still active when sci_probe() is called and the new serial port is supposed
to map to sci_ports[0], return -EBUSY to prevent breaking the earlycon.
This situation should occurs in debug scenarios, and users should be
aware of the potential conflict.
Fixes: 0b0cced19ab1 ("serial: sh-sci: Add CONFIG_SERIAL_EARLYCON support")
Cc: stable@vger.kernel.org
Signed-off-by: Claudiu Beznea <claudiu.beznea.uj@bp.renesas.com>
Link: https://lore.kernel.org/r/20250116182249.3828577-4-claudiu.beznea.uj@bp.renesas.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit eaeee4225dba30bef4d424bdf134a07b7f423e8b upstream.
The port_cfg object is used by serial_console_write(), which serves as
the write function for the earlycon device. Marking port_cfg as __initdata
causes it to be freed after kernel initialization, resulting in earlycon
becoming unavailable thereafter. Remove the __initdata macro from port_cfg
to resolve this issue.
Fixes: 0b0cced19ab1 ("serial: sh-sci: Add CONFIG_SERIAL_EARLYCON support")
Cc: stable@vger.kernel.org
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Claudiu Beznea <claudiu.beznea.uj@bp.renesas.com>
Fixes: 0b0cced19ab15c9e ("serial: sh-sci: Add CONFIG_SERIAL_EARLYCON support")
Link: https://lore.kernel.org/r/20250116182249.3828577-2-claudiu.beznea.uj@bp.renesas.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 2f83e38a095f8bf7c6029883d894668b03b9bd93 upstream.
With this, processes without CAP_SYS_ADMIN are able to use TIOCLINUX with
subcode TIOCL_SETSEL, in the selection modes TIOCL_SETPOINTER,
TIOCL_SELCLEAR and TIOCL_SELMOUSEREPORT.
TIOCL_SETSEL was previously changed to require CAP_SYS_ADMIN, as this IOCTL
let callers change the selection buffer and could be used to simulate
keypresses. These three TIOCL_SETSEL selection modes, however, are safe to
use, as they do not modify the selection buffer.
This fixes a mouse support regression that affected Emacs (invisible mouse
cursor).
Cc: stable <stable@kernel.org>
Link: https://lore.kernel.org/r/ee3ec63269b43b34e1c90dd8c9743bf8@finder.org
Fixes: 8d1b43f6a6df ("tty: Restrict access to TIOCLINUX' copy-and-paste subcommands")
Signed-off-by: Günther Noack <gnoack@google.com>
Reviewed-by: Kees Cook <kees@kernel.org>
Link: https://lore.kernel.org/r/20250110142122.1013222-1-gnoack@google.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit b06f388994500297bb91be60ffaf6825ecfd2afe upstream.
lockdep detects the following circular locking dependency:
CPU 0 CPU 1
========================== ============================
cdns_uart_isr() printk()
uart_port_lock(port) console_lock()
cdns_uart_console_write()
if (!port->sysrq)
uart_port_lock(port)
uart_handle_break()
port->sysrq = ...
uart_handle_sysrq_char()
printk()
console_lock()
The fixed commit attempts to avoid this situation by only taking the
port lock in cdns_uart_console_write if port->sysrq unset. However, if
(as shown above) cdns_uart_console_write runs before port->sysrq is set,
then it will try to take the port lock anyway. This may result in a
deadlock.
Fix this by splitting sysrq handling into two parts. We use the prepare
helper under the port lock and defer handling until we release the lock.
Fixes: 74ea66d4ca06 ("tty: xuartps: Improve sysrq handling")
Signed-off-by: Sean Anderson <sean.anderson@linux.dev>
Cc: stable@vger.kernel.org # c980248179d: serial: xilinx_uartps: Use port lock wrappers
Acked-by: John Ogness <john.ogness@linutronix.de>
Link: https://lore.kernel.org/r/20250110213822.2107462-1-sean.anderson@linux.dev
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit d91f98be26510f5f81ec66425bb0306d1ccd571a ]
After a console has written a record into UART_TX, it uses
wait_for_xmitr() to wait until the data has been sent out before
returning. However, wait_for_xmitr() will timeout after 10ms,
regardless if the data has been transmitted or not.
For single bytes, this timeout is sufficient even at very slow
baud rates, such as 1200bps. However, when FIFO mode is used,
there may be 64 bytes pushed into the FIFO at once. At a baud
rate of 115200bps, the 10ms timeout is still sufficient. But
when using lower baud rates (such as 57600bps), the timeout
is _not_ sufficient. This causes longer lines to be cut off,
resulting in lost and horribly misformatted output on the
console.
When using FIFO mode, take the number of bytes into account to
determine an appropriate maximum timeout. Increasing the timeout
does not affect performance since ideally the timeout never
occurs.
Fixes: 8f3631f0f6eb ("serial/8250: Use fifo in 8250 console driver")
Signed-off-by: John Ogness <john.ogness@linutronix.de>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Wander Lairson Costa <wander@redhat.com>
Reviewed-by: Petr Mladek <pmladek@suse.com>
Link: https://lore.kernel.org/r/20250107212702.169493-2-john.ogness@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 6dd1de91e7a62bfd3878992c1db6e1d443022c76 ]
The LKP robot complains about:
drivers/tty/mips_ejtag_fdc.c:1224:31: error: incompatible pointer types passing 'const char *[1]' to parameter of type 'const u8 **' (aka 'const unsigned char **')
Fix this by turning the missing pieces (fetch from kgdbfdc_wbuf) to u8
too. Note the filling part (kgdbfdc_write_char()) already receives and
stores u8 to kgdbfdc_wbuf.
Fixes: ce7cbd9a6c81 ("tty: mips_ejtag_fdc: use u8 for character pointers")
Reported-by: kernel test robot <lkp@intel.com>
Closes: https://lore.kernel.org/oe-kbuild-all/202501101327.oGdWbmuk-lkp@intel.com/
Signed-off-by: Jiri Slaby (SUSE) <jirislaby@kernel.org>
Link: https://lore.kernel.org/r/20250110115228.603980-1-jirislaby@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit ceb8bf2ceaa77fe222fe8fe32cb7789c9099ddf1 ]
Commit cdd30ebb1b9f ("module: Convert symbol namespace to string
literal") only converted MODULE_IMPORT_NS() and EXPORT_SYMBOL_NS(),
leaving DEFAULT_SYMBOL_NAMESPACE as a macro expansion.
This commit converts DEFAULT_SYMBOL_NAMESPACE in the same way to avoid
annoyance for the default namespace as well.
Signed-off-by: Masahiro Yamada <masahiroy@kernel.org>
Reviewed-by: Uwe Kleine-König <u.kleine-koenig@baylibre.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Stable-dep-of: 2505f87eb3af ("hwmon: (nct6775): Actually make use of the HWMON_NCT6775 symbol namespace")
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
commit 0cfc36ea51684b5932cd3951ded523777d807af2 upstream.
Commit 30e945861f3b ("serial: stm32: add support for break control")
added another usage of the port lock, but was merged on the same day as
c5d06662551c ("serial: stm32: Use port lock wrappers"), therefore the
latter did not update this usage to use the port lock wrappers.
Fixes: c5d06662551c ("serial: stm32: Use port lock wrappers")
Cc: stable <stable@kernel.org>
Signed-off-by: Ben Wolsieffer <ben.wolsieffer@hefring.com>
Reviewed-by: John Ogness <john.ogness@linutronix.de>
Link: https://lore.kernel.org/r/20241216145323.111612-1-ben.wolsieffer@hefring.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit ed2761958ad77e54791802b07095786150eab844 upstream.
The commit f9b11229b79c ("serial: 8250: Fix PM usage_count for console
handover") fixed one runtime PM usage counter balance problem that
occurs because .dev is not set during univ8250 setup preventing call to
pm_runtime_get_sync(). Later, univ8250_console_exit() will trigger the
runtime PM usage counter underflow as .dev is already set at that time.
Call pm_runtime_get_sync() to balance the RPM usage counter also in
serial8250_register_8250_port() before trying to add the port.
Reported-by: Borislav Petkov (AMD) <bp@alien8.de>
Fixes: bedb404e91bb ("serial: 8250_port: Don't use power management for kernel console")
Cc: stable <stable@kernel.org>
Tested-by: Borislav Petkov (AMD) <bp@alien8.de>
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Link: https://lore.kernel.org/r/20241210170120.2231-1-ilpo.jarvinen@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 7cc0e0a43a91052477c2921f924a37d9c3891f0c upstream.
On the Renesas RZ/G3S, when doing suspend to RAM, the uart_suspend_port()
is called. The uart_suspend_port() calls 3 times the
struct uart_port::ops::tx_empty() before shutting down the port.
According to the documentation, the struct uart_port::ops::tx_empty()
API tests whether the transmitter FIFO and shifter for the port is
empty.
The Renesas RZ/G3S SCIFA IP reports the number of data units stored in the
transmit FIFO through the FDR (FIFO Data Count Register). The data units
in the FIFOs are written in the shift register and transmitted from there.
The TEND bit in the Serial Status Register reports if the data was
transmitted from the shift register.
In the previous code, in the tx_empty() API implemented by the sh-sci
driver, it is considered that the TX is empty if the hardware reports the
TEND bit set and the number of data units in the FIFO is zero.
According to the HW manual, the TEND bit has the following meaning:
0: Transmission is in the waiting state or in progress.
1: Transmission is completed.
It has been noticed that when opening the serial device w/o using it and
then switch to a power saving mode, the tx_empty() call in the
uart_port_suspend() function fails, leading to the "Unable to drain
transmitter" message being printed on the console. This is because the
TEND=0 if nothing has been transmitted and the FIFOs are empty. As the
TEND=0 has double meaning (waiting state, in progress) we can't
determined the scenario described above.
Add a software workaround for this. This sets a variable if any data has
been sent on the serial console (when using PIO) or if the DMA callback has
been called (meaning something has been transmitted). In the tx_empty()
API the status of the DMA transaction is also checked and if it is
completed or in progress the code falls back in checking the hardware
registers instead of relying on the software variable.
Fixes: 73a19e4c0301 ("serial: sh-sci: Add DMA support.")
Cc: stable@vger.kernel.org
Signed-off-by: Claudiu Beznea <claudiu.beznea.uj@bp.renesas.com>
Link: https://lore.kernel.org/r/20241125115856.513642-1-claudiu.beznea.uj@bp.renesas.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit cad4dda82c7eedcfc22597267e710ccbcf39d572 ]
SG2044 relys on an internal divisor when calculating bitrate, which
means a wrong clock for the most common bitrates. So add a quirk for
this uart device to skip the set rate call and only relys on the
internal UART divisor.
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Signed-off-by: Inochi Amaoto <inochiama@gmail.com>
Link: https://lore.kernel.org/r/20241024062105.782330-4-inochiama@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
commit b5a23a60e8ab5711f4952912424347bf3864ce8d upstream.
When CONFIG_DMA_ENGINE is disabled, the driver now fails to build:
drivers/tty/serial/amba-pl011.c: In function 'pl011_unthrottle_rx':
drivers/tty/serial/amba-pl011.c:1822:16: error: 'struct uart_amba_port' has no member named 'using_rx_dma'
1822 | if (uap->using_rx_dma) {
| ^~
drivers/tty/serial/amba-pl011.c:1823:20: error: 'struct uart_amba_port' has no member named 'dmacr'
1823 | uap->dmacr |= UART011_RXDMAE;
| ^~
drivers/tty/serial/amba-pl011.c:1824:32: error: 'struct uart_amba_port' has no member named 'dmacr'
1824 | pl011_write(uap->dmacr, uap, REG_DMACR);
| ^~
Add the missing #ifdef check around these field accesses, matching
what other parts of this driver do.
Fixes: 2bcacc1c87ac ("serial: amba-pl011: Fix RX stall when DMA is used")
Cc: stable <stable@kernel.org>
Reported-by: kernel test robot <lkp@intel.com>
Closes: https://lore.kernel.org/oe-kbuild-all/202411140617.nkjeHhsK-lkp@intel.com/
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Link: https://lore.kernel.org/r/20241115110021.744332-1-arnd@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 2bcacc1c87acf9a8ebc17de18cb2b3cfeca547cf upstream.
Function pl011_throttle_rx() calls pl011_stop_rx() to disable RX, which
also disables the RX DMA by clearing the RXDMAE bit of the DMACR
register. However, to properly unthrottle RX when DMA is used, the
function pl011_unthrottle_rx() is expected to set the RXDMAE bit of
the DMACR register, which it currently lacks. This causes RX to stall
after the throttle API is called.
Set RXDMAE bit in the DMACR register while unthrottling RX if RX DMA is
used.
Fixes: 211565b10099 ("serial: pl011: UPSTAT_AUTORTS requires .throttle/unthrottle")
Cc: stable@vger.kernel.org
Signed-off-by: Kartik Rajput <kkartik@nvidia.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Link: https://lore.kernel.org/r/20241113092629.60226-1-kkartik@nvidia.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit bcc7ba668818dcadd2f1db66b39ed860a63ecf97 upstream.
Currently in omap_8250_shutdown, the dma->rx_running flag is
set to zero in omap_8250_rx_dma_flush. Next pm_runtime_get_sync
is called, which is a runtime resume call stack which can
re-set the flag. When the call omap_8250_shutdown returns, the
flag is expected to be UN-SET, but this is not the case. This
is causing issues the next time UART is re-opened and
omap_8250_rx_dma is called. Fix by moving pm_runtime_get_sync
before the omap_8250_rx_dma_flush.
cc: stable@vger.kernel.org
Fixes: 0e31c8d173ab ("tty: serial: 8250_omap: add custom DMA-RX callback")
Signed-off-by: Bin Liu <b-liu@ti.com>
[Judith: Add commit message]
Signed-off-by: Judith Mendez <jm@ti.com>
Reviewed-by: Kevin Hilman <khilman@baylibre.com>
Tested-by: Kevin Hilman <khilman@baylibre.com>
Link: https://lore.kernel.org/r/20241031172315.453750-1-jm@ti.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 166105c9030a30ba08574a9998afc7b60bc72dd7 upstream.
The F81216E is a LPC/eSPI to 4 UART Super I/O and is mostly compatible with
the F81216H, but does not support RS-485 auto-direction delays on any port.
Signed-off-by: Filip Brozovic <fbrozovic@gmail.com>
Cc: stable <stable@kernel.org>
Link: https://lore.kernel.org/r/20241110111703.15494-1-fbrozovic@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 718632467d88e98816fa01ab12681ef1c2aa56f8 upstream.
This reverts commit 3791ea69a4858b81e0277f695ca40f5aae40f312.
It was reported to cause boot-time issues, so revert it for now.
Reported-by: Geert Uytterhoeven <geert@linux-m68k.org>
Fixes: 3791ea69a485 ("serial: sh-sci: Clean sci_ports[0] after at earlycon exit")
Cc: stable <stable@kernel.org>
Cc: Claudiu Beznea <claudiu.beznea.uj@bp.renesas.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 3791ea69a4858b81e0277f695ca40f5aae40f312 upstream.
The early_console_setup() function initializes the sci_ports[0].port with
an object of type struct uart_port obtained from the object of type
struct earlycon_device received as argument by the early_console_setup().
It may happen that later, when the rest of the serial ports are probed,
the serial port that was used as earlycon (e.g., port A) to be mapped to a
different position in sci_ports[] and the slot 0 to be used by a different
serial port (e.g., port B), as follows:
sci_ports[0] = port A
sci_ports[X] = port B
In this case, the new port mapped at index zero will have associated data
that was used for earlycon.
In case this happens, after Linux boot, any access to the serial port that
maps on sci_ports[0] (port A) will block the serial port that was used as
earlycon (port B).
To fix this, add early_console_exit() that clean the sci_ports[0] at
earlycon exit time.
Fixes: 0b0cced19ab1 ("serial: sh-sci: Add CONFIG_SERIAL_EARLYCON support")
Cc: stable@vger.kernel.org
Signed-off-by: Claudiu Beznea <claudiu.beznea.uj@bp.renesas.com>
Link: https://lore.kernel.org/r/20241106120118.1719888-4-claudiu.beznea.uj@bp.renesas.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 635a9fca54f4f4148be1ae1c7c6bd37af80f5773 upstream.
Commit 7c0cca7c847e ("tty: ldisc: add sysctl to prevent autoloading of
ldiscs") introduces the tty_ldisc_autoload sysctl with the wrong
proc_handler. .extra1 and .extra2 parameters are set to avoid other values
thant SYSCTL_ZERO or SYSCTL_ONE to be set but proc_dointvec do not uses
them.
This commit fixes this by using proc_dointvec_minmax instead of
proc_dointvec.
Fixes: 7c0cca7c847e ("tty: ldisc: add sysctl to prevent autoloading of ldiscs")
Cc: stable <stable@kernel.org>
Signed-off-by: Nicolas Bouchinet <nicolas.bouchinet@ssi.gouv.fr>
Reviewed-by: Lin Feng <linf@wangsu.com>
Reviewed-by: Jiri Slaby <jirislaby@kernel.org>
Link: https://lore.kernel.org/r/20241112131357.49582-4-nicolas.bouchinet@clip-os.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Drop the unnecessary "_sys" infix from the suspend PM ops.
Signed-off-by: Johan Hovold <johan+linaro@kernel.org>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Link: https://lore.kernel.org/r/20241009145110.16847-10-johan+linaro@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Serial drivers should not be dropping characters themselves, but at
least drop the unused 'drop' parameter from the receive handler for now.
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Johan Hovold <johan+linaro@kernel.org>
Link: https://lore.kernel.org/r/20241009145110.16847-9-johan+linaro@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Drop the unnecessary WARN() in case the TTY buffers are ever full in
favour of a rate limited dev_err() which doesn't kill the machine when
panic_on_warn is set.
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Johan Hovold <johan+linaro@kernel.org>
Link: https://lore.kernel.org/r/20241009145110.16847-8-johan+linaro@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
The receiver is supposed to be enabled in the startup() callback and not
in set_termios() which is called also during console setup.
This specifically avoids accepting input before the port has been opened
(and interrupts enabled), something which can also break the GENI
firmware (cancel fails and after abort, the "stale" counter handling
appears to be broken so that later input is not processed until twelve
chars have been received).
There also does not appear to be any need to keep the receiver disabled
while updating the port settings.
Since commit 6f3c3cafb115 ("serial: qcom-geni: disable interrupts during
console writes") the calls to manipulate the secondary interrupts, which
were done without holding the port lock, can also lead to the receiver
being left disabled when set_termios() races with the console code (e.g.
when init opens the tty during boot). This can manifest itself as a
serial getty not accepting input.
The calls to stop and start rx in set_termios() can similarly race with
DMA completion and, for example, cause the DMA buffer to be unmapped
twice or the mapping to be leaked.
Fix this by only enabling the receiver during startup and while holding
the port lock to avoid racing with the console code.
Fixes: 6f3c3cafb115 ("serial: qcom-geni: disable interrupts during console writes")
Fixes: 2aaa43c70778 ("tty: serial: qcom-geni-serial: add support for serial engine DMA")
Fixes: c4f528795d1a ("tty: serial: msm_geni_serial: Add serial driver support for GENI based QUP")
Cc: stable@vger.kernel.org # 6.3
Cc: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Signed-off-by: Johan Hovold <johan+linaro@kernel.org>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Link: https://lore.kernel.org/r/20241009145110.16847-6-johan+linaro@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Make sure to wait for the DMA transfer to complete when cancelling the
rx command on stop_rx(). This specifically prevents the DMA completion
interrupt from firing after rx has been restarted, something which can
lead to an IOMMU fault and hosed rx when the interrupt handler unmaps
the DMA buffer for the new command:
qcom_geni_serial 988000.serial: serial engine reports 0 RX bytes in!
arm-smmu 15000000.iommu: FSR = 00000402 [Format=2 TF], SID=0x563
arm-smmu 15000000.iommu: FSYNR0 = 00210013 [S1CBNDX=33 WNR PLVL=3]
Bluetooth: hci0: command 0xfc00 tx timeout
Bluetooth: hci0: Reading QCA version information failed (-110)
Also add the missing state machine reset which is needed in case
cancellation fails.
Fixes: 2aaa43c70778 ("tty: serial: qcom-geni-serial: add support for serial engine DMA")
Cc: stable@vger.kernel.org # 6.3
Cc: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Signed-off-by: Johan Hovold <johan+linaro@kernel.org>
Link: https://lore.kernel.org/r/20241009145110.16847-5-johan+linaro@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
A commit adding back the stopping of tx on port shutdown failed to add
back the locking which had also been removed by commit e83766334f96
("tty: serial: qcom_geni_serial: No need to stop tx/rx on UART
shutdown").
Holding the port lock is needed to serialise against the console code,
which may update the interrupt enable register and access the port
state.
Fixes: d8aca2f96813 ("tty: serial: qcom-geni-serial: stop operations in progress at shutdown")
Fixes: 947cc4ecc06c ("serial: qcom-geni: fix soft lockup on sw flow control and suspend")
Cc: stable@vger.kernel.org # 6.3
Reviewed-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Signed-off-by: Johan Hovold <johan+linaro@kernel.org>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Link: https://lore.kernel.org/r/20241009145110.16847-4-johan+linaro@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
This reverts commit 35781d8356a2eecaa6074ceeb80ee22e252fcdae.
Hibernation is not supported on Qualcomm platforms with mainline
kernels yet a broken vendor implementation for the GENI serial driver
made it upstream.
This is effectively dead code that cannot be tested and should just be
removed, but if these paths were ever hit for an open non-console port
they would crash the machine as the driver would fail to enable clocks
during restore() (i.e. all ports would have to be closed by drivers and
user space before hibernating the system to avoid this as a comment in
the code hinted at).
The broken implementation also added a random call to enable the
receiver in the port setup code where it does not belong and which
enables the receiver prematurely for console ports.
Fixes: 35781d8356a2 ("tty: serial: qcom-geni-serial: Add support for Hibernation feature")
Cc: stable@vger.kernel.org # 6.2
Cc: Aniket Randive <quic_arandive@quicinc.com>
Signed-off-by: Johan Hovold <johan+linaro@kernel.org>
Link: https://lore.kernel.org/r/20241009145110.16847-3-johan+linaro@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
The polled console (KGDB/KDB) implementation must not call port setup
unconditionally as the port may already be in use by the console or a
getty.
Only make sure that the receiver is enabled, but do not enable any
device interrupts.
Fixes: d8851a96ba25 ("tty: serial: qcom-geni-serial: Add a poll_init() function")
Cc: stable@vger.kernel.org # 6.4
Cc: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Johan Hovold <johan+linaro@kernel.org>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Link: https://lore.kernel.org/r/20241009145110.16847-2-johan+linaro@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
When sending data using DMA at high baudrate (4 Mbdps in local test case) to
a device with small RX buffer which keeps asserting RTS after every received
byte, it is possible that the iMX UART driver would not recognize the falling
edge of RTS input signal and get stuck, unable to transmit any more data.
This condition happens when the following sequence of events occur:
- imx_uart_mctrl_check() is called at some point and takes a snapshot of UART
control signal status into sport->old_status using imx_uart_get_hwmctrl().
The RTSS/TIOCM_CTS bit is of interest here (*).
- DMA transfer occurs, the remote device asserts RTS signal after each byte.
The i.MX UART driver recognizes each such RTS signal change, raises an
interrupt with USR1 register RTSD bit set, which leads to invocation of
__imx_uart_rtsint(), which calls uart_handle_cts_change().
- If the RTS signal is deasserted, uart_handle_cts_change() clears
port->hw_stopped and unblocks the port for further data transfers.
- If the RTS is asserted, uart_handle_cts_change() sets port->hw_stopped
and blocks the port for further data transfers. This may occur as the
last interrupt of a transfer, which means port->hw_stopped remains set
and the port remains blocked (**).
- Any further data transfer attempts will trigger imx_uart_mctrl_check(),
which will read current status of UART control signals by calling
imx_uart_get_hwmctrl() (***) and compare it with sport->old_status .
- If current status differs from sport->old_status for RTS signal,
uart_handle_cts_change() is called and possibly unblocks the port
by clearing port->hw_stopped .
- If current status does not differ from sport->old_status for RTS
signal, no action occurs. This may occur in case prior snapshot (*)
was taken before any transfer so the RTS is deasserted, current
snapshot (***) was taken after a transfer and therefore RTS is
deasserted again, which means current status and sport->old_status
are identical. In case (**) triggered when RTS got asserted, and
made port->hw_stopped set, the port->hw_stopped will remain set
because no change on RTS line is recognized by this driver and
uart_handle_cts_change() is not called from here to unblock the
port->hw_stopped.
Update sport->old_status in __imx_uart_rtsint() accordingly to make
imx_uart_mctrl_check() detect such RTS change. Note that TIOCM_CAR
and TIOCM_RI bits in sport->old_status do not suffer from this problem.
Fixes: ceca629e0b48 ("[ARM] 2971/1: i.MX uart handle rts irq")
Cc: stable <stable@kernel.org>
Reviewed-by: Esben Haabendal <esben@geanix.com>
Signed-off-by: Marek Vasut <marex@denx.de>
Link: https://lore.kernel.org/r/20241002184133.19427-1-marex@denx.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
BUG: KASAN: slab-use-after-free in gsm_cleanup_mux+0x77b/0x7b0
drivers/tty/n_gsm.c:3160 [n_gsm]
Read of size 8 at addr ffff88815fe99c00 by task poc/3379
CPU: 0 UID: 0 PID: 3379 Comm: poc Not tainted 6.11.0+ #56
Hardware name: VMware, Inc. VMware Virtual Platform/440BX
Desktop Reference Platform, BIOS 6.00 11/12/2020
Call Trace:
<TASK>
gsm_cleanup_mux+0x77b/0x7b0 drivers/tty/n_gsm.c:3160 [n_gsm]
__pfx_gsm_cleanup_mux+0x10/0x10 drivers/tty/n_gsm.c:3124 [n_gsm]
__pfx_sched_clock_cpu+0x10/0x10 kernel/sched/clock.c:389
update_load_avg+0x1c1/0x27b0 kernel/sched/fair.c:4500
__pfx_min_vruntime_cb_rotate+0x10/0x10 kernel/sched/fair.c:846
__rb_insert_augmented+0x492/0xbf0 lib/rbtree.c:161
gsmld_ioctl+0x395/0x1450 drivers/tty/n_gsm.c:3408 [n_gsm]
_raw_spin_lock_irqsave+0x92/0xf0 arch/x86/include/asm/atomic.h:107
__pfx_gsmld_ioctl+0x10/0x10 drivers/tty/n_gsm.c:3822 [n_gsm]
ktime_get+0x5e/0x140 kernel/time/timekeeping.c:195
ldsem_down_read+0x94/0x4e0 arch/x86/include/asm/atomic64_64.h:79
__pfx_ldsem_down_read+0x10/0x10 drivers/tty/tty_ldsem.c:338
__pfx_do_vfs_ioctl+0x10/0x10 fs/ioctl.c:805
tty_ioctl+0x643/0x1100 drivers/tty/tty_io.c:2818
Allocated by task 65:
gsm_data_alloc.constprop.0+0x27/0x190 drivers/tty/n_gsm.c:926 [n_gsm]
gsm_send+0x2c/0x580 drivers/tty/n_gsm.c:819 [n_gsm]
gsm1_receive+0x547/0xad0 drivers/tty/n_gsm.c:3038 [n_gsm]
gsmld_receive_buf+0x176/0x280 drivers/tty/n_gsm.c:3609 [n_gsm]
tty_ldisc_receive_buf+0x101/0x1e0 drivers/tty/tty_buffer.c:391
tty_port_default_receive_buf+0x61/0xa0 drivers/tty/tty_port.c:39
flush_to_ldisc+0x1b0/0x750 drivers/tty/tty_buffer.c:445
process_scheduled_works+0x2b0/0x10d0 kernel/workqueue.c:3229
worker_thread+0x3dc/0x950 kernel/workqueue.c:3391
kthread+0x2a3/0x370 kernel/kthread.c:389
ret_from_fork+0x2d/0x70 arch/x86/kernel/process.c:147
ret_from_fork_asm+0x1a/0x30 arch/x86/entry/entry_64.S:257
Freed by task 3367:
kfree+0x126/0x420 mm/slub.c:4580
gsm_cleanup_mux+0x36c/0x7b0 drivers/tty/n_gsm.c:3160 [n_gsm]
gsmld_ioctl+0x395/0x1450 drivers/tty/n_gsm.c:3408 [n_gsm]
tty_ioctl+0x643/0x1100 drivers/tty/tty_io.c:2818
[Analysis]
gsm_msg on the tx_ctrl_list or tx_data_list of gsm_mux
can be freed by multi threads through ioctl,which leads
to the occurrence of uaf. Protect it by gsm tx lock.
Signed-off-by: Longlong Xia <xialonglong@kylinos.cn>
Cc: stable <stable@kernel.org>
Suggested-by: Jiri Slaby <jirislaby@kernel.org>
Link: https://lore.kernel.org/r/20240926130213.531959-1-xialonglong@kylinos.cn
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
font.data may not initialize all memory spaces depending on the implementation
of vc->vc_sw->con_font_get. This may cause info-leak, so to prevent this, it
is safest to modify it to initialize the allocated memory space to 0, and it
generally does not affect the overall performance of the system.
Cc: stable@vger.kernel.org
Reported-by: syzbot+955da2d57931604ee691@syzkaller.appspotmail.com
Fixes: 05e2600cb0a4 ("VT: Bump font size limitation to 64x128 pixels")
Signed-off-by: Jeongjun Park <aha310510@gmail.com>
Link: https://lore.kernel.org/r/20241010174619.59662-1-aha310510@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
asm/unaligned.h is always an include of asm-generic/unaligned.h;
might as well move that thing to linux/unaligned.h and include
that - there's nothing arch-specific in that header.
auto-generated by the following:
for i in `git grep -l -w asm/unaligned.h`; do
sed -i -e "s/asm\/unaligned.h/linux\/unaligned.h/" $i
done
for i in `git grep -l -w asm-generic/unaligned.h`; do
sed -i -e "s/asm-generic\/unaligned.h/linux\/unaligned.h/" $i
done
git mv include/asm-generic/unaligned.h include/linux/unaligned.h
git mv tools/include/asm-generic/unaligned.h tools/include/linux/unaligned.h
sed -i -e "/unaligned.h/d" include/asm-generic/Kbuild
sed -i -e "s/__ASM_GENERIC/__LINUX/" include/linux/unaligned.h tools/include/linux/unaligned.h
|
|
no_llseek had been defined to NULL two years ago, in commit 868941b14441
("fs: remove no_llseek")
To quote that commit,
At -rc1 we'll need do a mechanical removal of no_llseek -
git grep -l -w no_llseek | grep -v porting.rst | while read i; do
sed -i '/\<no_llseek\>/d' $i
done
would do it.
Unfortunately, that hadn't been done. Linus, could you do that now, so
that we could finally put that thing to rest? All instances are of the
form
.llseek = no_llseek,
so it's obviously safe.
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty
Pull tty / serial driver updates from Greg KH:
"Here is the "big" set of tty/serial driver updates for 6.12-rc1.
Nothing major in here, just nice forward progress in the slow cleanup
of the serial apis, and lots of other driver updates and fixes.
Included in here are:
- serial api updates from Jiri to make things more uniform and sane
- 8250_platform driver cleanups
- samsung serial driver fixes and updates
- qcom-geni serial driver fixes from Johan for the bizarre UART
engine that that chip seems to have. Hopefully it's in a better
state now, but hardware designers still seem to come up with more
ways to make broken UARTS 40+ years after this all should have
finished.
- sc16is7xx driver updates
- omap 8250 driver updates
- 8250_bcm2835aux driver updates
- a few new serial driver bindings added
- other serial minor driver updates
All of these have been in linux-next for a long time with no reported
problems"
* tag 'tty-6.12-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty: (65 commits)
tty: serial: samsung: Fix serial rx on Apple A7-A9
tty: serial: samsung: Fix A7-A11 serial earlycon SError
tty: serial: samsung: Use bit manipulation macros for APPLE_S5L_*
tty: rp2: Fix reset with non forgiving PCIe host bridges
serial: 8250_aspeed_vuart: Enable module autoloading
serial: qcom-geni: fix polled console corruption
serial: qcom-geni: disable interrupts during console writes
serial: qcom-geni: fix console corruption
serial: qcom-geni: introduce qcom_geni_serial_poll_bitfield()
serial: qcom-geni: fix arg types for qcom_geni_serial_poll_bit()
soc: qcom: geni-se: add GP_LENGTH/IRQ_EN_SET/IRQ_EN_CLEAR registers
serial: qcom-geni: fix false console tx restart
serial: qcom-geni: fix fifo polling timeout
tty: hvc: convert comma to semicolon
mxser: convert comma to semicolon
serial: 8250_bcm2835aux: Fix clock imbalance in PM resume
serial: sc16is7xx: convert bitmask definitions to use BIT() macro
serial: sc16is7xx: fix copy-paste errors in EFR_SWFLOWx_BIT constants
serial: sc16is7xx: remove SC16IS7XX_MSR_DELTA_MASK
serial: xilinx_uartps: Make cdns_rs485_supported static
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tj/sched_ext
Pull sched_ext support from Tejun Heo:
"This implements a new scheduler class called ‘ext_sched_class’, or
sched_ext, which allows scheduling policies to be implemented as BPF
programs.
The goals of this are:
- Ease of experimentation and exploration: Enabling rapid iteration
of new scheduling policies.
- Customization: Building application-specific schedulers which
implement policies that are not applicable to general-purpose
schedulers.
- Rapid scheduler deployments: Non-disruptive swap outs of scheduling
policies in production environments"
See individual commits for more documentation, but also the cover letter
for the latest series:
Link: https://lore.kernel.org/all/20240618212056.2833381-1-tj@kernel.org/
* tag 'sched_ext-for-6.12' of git://git.kernel.org/pub/scm/linux/kernel/git/tj/sched_ext: (110 commits)
sched: Move update_other_load_avgs() to kernel/sched/pelt.c
sched_ext: Don't trigger ops.quiescent/runnable() on migrations
sched_ext: Synchronize bypass state changes with rq lock
scx_qmap: Implement highpri boosting
sched_ext: Implement scx_bpf_dispatch[_vtime]_from_dsq()
sched_ext: Compact struct bpf_iter_scx_dsq_kern
sched_ext: Replace consume_local_task() with move_local_task_to_local_dsq()
sched_ext: Move consume_local_task() upward
sched_ext: Move sanity check and dsq_mod_nr() into task_unlink_from_dsq()
sched_ext: Reorder args for consume_local/remote_task()
sched_ext: Restructure dispatch_to_local_dsq()
sched_ext: Fix processs_ddsp_deferred_locals() by unifying DTL_INVALID handling
sched_ext: Make find_dsq_for_dispatch() handle SCX_DSQ_LOCAL_ON
sched_ext: Refactor consume_remote_task()
sched_ext: Rename scx_kfunc_set_sleepable to unlocked and relocate
sched_ext: Add missing static to scx_dump_data
sched_ext: Add missing static to scx_has_op[]
sched_ext: Temporarily work around pick_task_scx() being called without balance_scx()
sched_ext: Add a cgroup scheduler which uses flattened hierarchy
sched_ext: Add cgroup support
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/printk/linux
Pull printk updates from Petr Mladek:
"This is the "last" part of the support for the new nbcon consoles.
Where "nbcon" stays for "No Big console lock CONsoles" aka not under
the console_lock.
New callbacks are added to struct console:
- write_thread() for flushing nbcon consoles in task context.
- write_atomic() for flushing nbcon consoles in atomic context,
including NMI.
- con->device_lock() and device_unlock() for taking the driver
specific lock, for example, port->lock.
New printk-specific kthreads are created:
- per-console kthreads which get responsible for flushing normal
priority messages on nbcon consoles.
- thread which gets responsible for flushing normal priority messages
on all consoles when CONFIG_RT enabled.
The new callbacks are called under a special per-console lock which
has already been added back in v6.7. It allows to distinguish three
severities: normal, emergency, and panic. A context with a higher
priority could take over the ownership when it is safe even in the
middle of handling a record. The panic context could do it even when
it is not safe. But it is allowed only for the final desperate flush
before entering the infinite loop.
The new lock helps to flush the messages directly in emergency and
panic contexts. But it is not enough in all situations:
- console_lock() is still need for synchronization against boot
consoles.
- con->device_lock() is need for synchronization against other
operations on the same HW, e.g. serial port speed setting,
non-printk related read/write.
The dependency on con->device_lock() is mutual. Any code taking the
driver specific lock has to acquire the related nbcon console context
as well. For example, see the new uart_port_lock() API. It provides
the necessary synchronization against emergency and panic contexts
where the messages are flushed only under the new per-console lock.
Maybe surprisingly, a quite tricky part is the decision how to flush
the consoles in various situations. It has to take into account:
- message priority: normal, emergency, panic
- scheduling context: task, atomic, deferred_legacy
- registered consoles: boot, legacy, nbcon
- threads are running: early boot, suspend, shutdown, panic
- caller: printk(), pr_flush(), printk_flush_in_panic(),
console_unlock(), console_start(), ...
The primary decision is made in printk_get_console_flush_type(). It
creates a hint what the caller should do:
- flush nbcon consoles directly or via the kthread
- call the legacy loop (console_unlock()) directly or via irq_work
The existing behavior is preserved for the legacy consoles. The only
exception is that they are not longer flushed directly from printk()
in panic() before CPUs are stopped. But this blocking happens only
when at least one nbcon console is registered. The motivation is to
increase a chance to produce the crash dump. They legacy consoles
might create a deadlock in compare with nbcon consoles. The nbcon
console should allow to see the messages even when the crash dump
fails.
There are three possible ways how nbcon consoles are flushed:
- The per-nbcon-console kthread is responsible for flushing messages
added with the normal priority. This is the default mode.
- The legacy loop, aka console_unlock(), is used when there is still
a boot console registered. There is no easy way how to match an
early console driver with a nbcon console driver. And the
console_lock() provides the only reliable serialization at the
moment.
The legacy loop uses either con->write_atomic() or
con->write_thread() callbacks depending on whether it is allowed to
schedule. The atomic variant has to be used from printk().
- In other situations, the messages are flushed directly using
write_atomic() which can be called in any context, including NMI.
It is primary needed during early boot or shutdown, in emergency
situations, and panic.
The emergency priority is used by a code called within
nbcon_cpu_emergency_enter()/exit(). At the moment, it is used in four
situations: WARN(), Oops, lockdep, and RCU stall reports.
Finally, there is no nbcon console at the moment. It means that the
changes should _not_ modify the existing behavior. The only exception
is CONFIG_RT which would force offloading the legacy loop, for normal
priority context, into the dedicated kthread"
* tag 'printk-for-6.12' of git://git.kernel.org/pub/scm/linux/kernel/git/printk/linux: (54 commits)
printk: Avoid false positive lockdep report for legacy printing
printk: nbcon: Assign nice -20 for printing threads
printk: Implement legacy printer kthread for PREEMPT_RT
tty: sysfs: Add nbcon support for 'active'
proc: Add nbcon support for /proc/consoles
proc: consoles: Add notation to c_start/c_stop
printk: nbcon: Show replay message on takeover
printk: Provide helper for message prepending
printk: nbcon: Rely on kthreads for normal operation
printk: nbcon: Use thread callback if in task context for legacy
printk: nbcon: Relocate nbcon_atomic_emit_one()
printk: nbcon: Introduce printer kthreads
printk: nbcon: Init @nbcon_seq to highest possible
printk: nbcon: Add context to usable() and emit()
printk: Flush console on unregister_console()
printk: Fail pr_flush() if before SYSTEM_SCHEDULING
printk: nbcon: Add function for printers to reacquire ownership
printk: nbcon: Use raw_cpu_ptr() instead of open coding
printk: Use the BITS_PER_LONG macro
lockdep: Mark emergency sections in lockdep splats
...
|
|
Apple's older A7-A9 SoCs seems to use bit 3 in UTRSTAT as RXTO, which is
enabled by bit 11 in UCON.
Access these bits in addition to the original RXTO and RXTO enable bits,
to allow serial rx to function on A7-A9 SoCs. This change does not
appear to affect the A10 SoC and up.
Tested-by: Janne Grunau <j@jannau.net>
Reviewed-by: Neal Gompa <neal@gompa.dev>
Signed-off-by: Nick Chan <towinchenmi@gmail.com>
Reviewed-by: Andi Shyti <andi.shyti@kernel.org>
Link: https://lore.kernel.org/r/20240911050741.14477-4-towinchenmi@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Apple's earlier SoCs, like A7-A11, requires 32-bit writes for the serial
port. Otherwise, a SError happens when writing to UTXH (+0x20). This only
manifested in earlycon as reg-io-width in the device tree is consulted
for normal serial writes.
Change the iotype of the port to UPIO_MEM32, to allow the serial port to
function on A7-A11 SoCs. This change does not appear to affect Apple M1 and
above.
Reviewed-by: Krzysztof Kozlowski <krzk@kernel.org>
Reviewed-by: Neal Gompa <neal@gompa.dev>
Tested-by: Janne Grunau <j@jannau.net>
Signed-off-by: Nick Chan <towinchenmi@gmail.com>
Reviewed-by: Andi Shyti <andi.shyti@kernel.org>
Link: https://lore.kernel.org/r/20240911050741.14477-3-towinchenmi@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
The write to RP2_GLOBAL_CMD followed by an immediate read of
RP2_GLOBAL_CMD in rp2_reset_asic() is intented to flush out the write,
however by then the device is already in reset and cannot respond to a
memory cycle access.
On platforms such as the Raspberry Pi 4 and others using the
pcie-brcmstb.c driver, any memory access to a device that cannot respond
is met with a fatal system error, rather than being substituted with all
1s as is usually the case on PC platforms.
Swapping the delay and the read ensures that the device has finished
resetting before we attempt to read from it.
Fixes: 7d9f49afa451 ("serial: rp2: New driver for Comtrol RocketPort 2 cards")
Cc: stable <stable@kernel.org>
Suggested-by: Jim Quinlan <james.quinlan@broadcom.com>
Signed-off-by: Florian Fainelli <florian.fainelli@broadcom.com>
Link: https://lore.kernel.org/r/20240906225435.707837-1-florian.fainelli@broadcom.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Add MODULE_DEVICE_TABLE(), so modules could be properly autoloaded based
on the alias from of_device_id table.
Signed-off-by: Liao Chen <liaochen4@huawei.com>
Acked-by: Uwe Kleine-König <u.kleine-koenig@baylibre.com>
Link: https://lore.kernel.org/r/20240903131503.961178-1-liaochen4@huawei.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
The polled UART operations are used by the kernel debugger (KDB, KGDB),
which can interrupt the kernel at any point in time. The current
Qualcomm GENI implementation does not really work when there is on-going
serial output as it inadvertently "hijacks" the current tx command,
which can result in both the initial debugger output being corrupted as
well as the corruption of any on-going serial output (up to 4k
characters) when execution resumes:
0190: abcdefghijklmnopqrstuvwxyz0123456789 0190: abcdefghijklmnopqrstuvwxyz0123456789
0191: abcdefghijklmnop[ 50.825552] sysrq: DEBUG
qrstuvwxyz0123456789 0191: abcdefghijklmnopqrstuvwxyz0123456789
Entering kdb (current=0xffff53510b4cd280, pid 640) on processor 2 due to Keyboard Entry
[2]kdb> go
omlji3h3h2g2g1f1f0e0ezdzdycycxbxbwawav :t72r2rp
o9n976k5j5j4i4i3h3h2g2g1f1f0e0ezdzdycycxbxbwawavu:t7t8s8s8r2r2q0q0p
o9n9n8ml6k6k5j5j4i4i3h3h2g2g1f1f0e0ezdzdycycxbxbwawav v u:u:t9t0s4s4rq0p
o9n9n8m8m7l7l6k6k5j5j40q0p p o
o9n9n8m8m7l7l6k6k5j5j4i4i3h3h2g2g1f1f0e0ezdzdycycxbxbwawav :t8t9s4s4r4r4q0q0p
Fix this by making sure that the polled output implementation waits for
the tx fifo to drain before cancelling any on-going longer transfers. As
the polled code cannot take any locks, leave the state variables as they
are and instead make sure that the interrupt handler always starts a new
tx command when there is data in the write buffer.
Since the debugger can interrupt the interrupt handler when it is
writing data to the tx fifo, it is currently not possible to fully
prevent losing up to 64 bytes of tty output on resume.
Fixes: c4f528795d1a ("tty: serial: msm_geni_serial: Add serial driver support for GENI based QUP")
Cc: stable@vger.kernel.org # 4.17
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Tested-by: Nícolas F. R. A. Prado <nfraprado@collabora.com>
Signed-off-by: Johan Hovold <johan+linaro@kernel.org>
Link: https://lore.kernel.org/r/20240906131336.23625-9-johan+linaro@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
