| Age | Commit message (Collapse) | Author |
|---|
|
commit d96f04d347e4011977abdbb4da5d8f303ebd26f8 upstream.
It has been observed that once per 300-1300 port openings the first
transmitted byte is being corrupted on AM3352 ("v" written to FIFO appeared
as "e" on the wire). It only happened if single byte has been transmitted
right after port open, which means, DMA is not used for this transfer and
the corruption never happened afterwards.
Therefore I've carefully re-read the MDR1 errata (link below), which says
"when accessing the MDR1 registers that causes a dummy under-run condition
that will freeze the UART in IrDA transmission. In UART mode, this may
corrupt the transferred data". Strictly speaking,
omap_8250_mdr1_errataset() performs a read access and if the value is the
same as should be written, exits without errata-recommended FIFO reset.
A brief check of the serial_omap_mdr1_errataset() from the competing
omap-serial driver showed it has no read access of MDR1. After removing the
read access from omap_8250_mdr1_errataset() the data corruption never
happened any more.
Link: https://www.ti.com/lit/er/sprz360i/sprz360i.pdf
Fixes: 61929cf0169d ("tty: serial: Add 8250-core based omap driver")
Cc: stable@vger.kernel.org
Signed-off-by: Alexander Sverdlin <alexander.sverdlin@gmail.com>
Link: https://lore.kernel.org/r/20201210055257.1053028-1-alexander.sverdlin@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit c8bcd9c5be24fb9e6132e97da5a35e55a83e36b9 upstream.
Currently, locking of ->session is very inconsistent; most places
protect it using the legacy tty mutex, but disassociate_ctty(),
__do_SAK(), tiocspgrp() and tiocgsid() don't.
Two of the writers hold the ctrl_lock (because they already need it for
->pgrp), but __proc_set_tty() doesn't do that yet.
On a PREEMPT=y system, an unprivileged user can theoretically abuse
this broken locking to read 4 bytes of freed memory via TIOCGSID if
tiocgsid() is preempted long enough at the right point. (Other things
might also go wrong, especially if root-only ioctls are involved; I'm
not sure about that.)
Change the locking on ->session such that:
- tty_lock() is held by all writers: By making disassociate_ctty()
hold it. This should be fine because the same lock can already be
taken through the call to tty_vhangup_session().
The tricky part is that we need to shorten the area covered by
siglock to be able to take tty_lock() without ugly retry logic; as
far as I can tell, this should be fine, since nothing in the
signal_struct is touched in the `if (tty)` branch.
- ctrl_lock is held by all writers: By changing __proc_set_tty() to
hold the lock a little longer.
- All readers that aren't holding tty_lock() hold ctrl_lock: By
adding locking to tiocgsid() and __do_SAK(), and expanding the area
covered by ctrl_lock in tiocspgrp().
Cc: stable@kernel.org
Signed-off-by: Jann Horn <jannh@google.com>
Reviewed-by: Jiri Slaby <jirislaby@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 54ffccbf053b5b6ca4f6e45094b942fab92a25fc upstream.
tiocspgrp() takes two tty_struct pointers: One to the tty that userspace
passed to ioctl() (`tty`) and one to the TTY being changed (`real_tty`).
These pointers are different when ioctl() is called with a master fd.
To properly lock real_tty->pgrp, we must take real_tty->ctrl_lock.
This bug makes it possible for racing ioctl(TIOCSPGRP, ...) calls on
both sides of a PTY pair to corrupt the refcount of `struct pid`,
leading to use-after-free errors.
Fixes: 47f86834bbd4 ("redo locking of tty->pgrp")
CC: stable@kernel.org
Signed-off-by: Jann Horn <jannh@google.com>
Reviewed-by: Jiri Slaby <jirislaby@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit e67c139c488e84e7eae6c333231e791f0e89b3fb upstream.
For below code, there has chance to cause deadlock in SMP system:
Thread 1:
clk_enable_lock();
pr_info("debug message");
clk_enable_unlock();
Thread 2:
imx_uart_console_write()
clk_enable()
clk_enable_lock();
Thread 1:
Acuired clk enable_lock -> printk -> console_trylock_spinning
Thread 2:
console_unlock() -> imx_uart_console_write -> clk_disable -> Acquite clk enable_lock
So the patch is to keep console port clocks always on like
other console drivers.
Fixes: 1cf93e0d5488 ("serial: imx: remove the uart_console() check")
Acked-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Fugang Duan <fugang.duan@nxp.com>
Link: https://lore.kernel.org/r/20201111025136.29818-1-fugang.duan@nxp.com
Cc: stable <stable@vger.kernel.org>
[fix up build warning - gregkh]
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
serial_txx9_init
commit 0c5fc92622ed5531ff324b20f014e9e3092f0187 upstream.
Add the missing platform_driver_unregister() before return
from serial_txx9_init in the error handling case when failed
to register serial_txx9_pci_driver with macro ENABLE_SERIAL_TXX9_PCI
defined.
Fixes: ab4382d27412 ("tty: move drivers/serial/ to drivers/tty/serial/")
Signed-off-by: Qinglang Miao <miaoqinglang@huawei.com>
Link: https://lore.kernel.org/r/20201103084942.109076-1-miaoqinglang@huawei.com
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 912ab37c798770f21b182d656937072b58553378 upstream.
Mediatek 8250 port supports speed higher than uartclk / 16. If the baud
rates in both the new and the old termios setting are higher than
uartclk / 16, the WARN_ON in uart_get_baud_rate() will be triggered.
Passing NULL as the old termios so uart_get_baud_rate() will use
uartclk / 16 - 1 as the new baud rate which will be replaced by the
original baud rate later by tty_termios_encode_baud_rate() in
mtk8250_set_termios().
Fixes: 551e553f0d4a ("serial: 8250_mtk: Fix high-speed baud rates clamping")
Signed-off-by: Claire Chang <tientzu@chromium.org>
Link: https://lore.kernel.org/r/20201102120749.374458-1-tientzu@chromium.org
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 3c4e0dff2095c579b142d5a0693257f1c58b4804 upstream.
It's buggy:
On Fri, Nov 06, 2020 at 10:30:08PM +0800, Minh Yuan wrote:
> We recently discovered a slab-out-of-bounds read in fbcon in the latest
> kernel ( v5.10-rc2 for now ). The root cause of this vulnerability is that
> "fbcon_do_set_font" did not handle "vc->vc_font.data" and
> "vc->vc_font.height" correctly, and the patch
> <https://lkml.org/lkml/2020/9/27/223> for VT_RESIZEX can't handle this
> issue.
>
> Specifically, we use KD_FONT_OP_SET to set a small font.data for tty6, and
> use KD_FONT_OP_SET again to set a large font.height for tty1. After that,
> we use KD_FONT_OP_COPY to assign tty6's vc_font.data to tty1's vc_font.data
> in "fbcon_do_set_font", while tty1 retains the original larger
> height. Obviously, this will cause an out-of-bounds read, because we can
> access a smaller vc_font.data with a larger vc_font.height.
Further there was only one user ever.
- Android's loadfont, busybox and console-tools only ever use OP_GET
and OP_SET
- fbset documentation only mentions the kernel cmdline font: option,
not anything else.
- systemd used OP_COPY before release 232 published in Nov 2016
Now unfortunately the crucial report seems to have gone down with
gmane, and the commit message doesn't say much. But the pull request
hints at OP_COPY being broken
https://github.com/systemd/systemd/pull/3651
So in other words, this never worked, and the only project which
foolishly every tried to use it, realized that rather quickly too.
Instead of trying to fix security issues here on dead code by adding
missing checks, fix the entire thing by removing the functionality.
Note that systemd code using the OP_COPY function ignored the return
value, so it doesn't matter what we're doing here really - just in
case a lone server somewhere happens to be extremely unlucky and
running an affected old version of systemd. The relevant code from
font_copy_to_all_vcs() in systemd was:
/* copy font from active VT, where the font was uploaded to */
cfo.op = KD_FONT_OP_COPY;
cfo.height = vcs.v_active-1; /* tty1 == index 0 */
(void) ioctl(vcfd, KDFONTOP, &cfo);
Note this just disables the ioctl, garbage collecting the now unused
callbacks is left for -next.
v2: Tetsuo found the old mail, which allowed me to find it on another
archive. Add the link too.
Acked-by: Peilin Ye <yepeilin.cs@gmail.com>
Reported-by: Minh Yuan <yuanmingbuaa@gmail.com>
References: https://lists.freedesktop.org/archives/systemd-devel/2016-June/036935.html
References: https://github.com/systemd/systemd/pull/3651
Cc: Greg KH <greg@kroah.com>
Cc: Peilin Ye <yepeilin.cs@gmail.com>
Cc: Tetsuo Handa <penguin-kernel@i-love.sakura.ne.jp>
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
Link: https://lore.kernel.org/r/20201108153806.3140315-1-daniel.vetter@ffwll.ch
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 90bfdeef83f1d6c696039b6a917190dcbbad3220 upstream.
Some of the font tty ioctl's always used the current foreground VC for
their operations. Don't do that then.
This fixes a data race on fg_console.
Side note: both Michael Ellerman and Jiri Slaby point out that all these
ioctls are deprecated, and should probably have been removed long ago,
and everything seems to be using the KDFONTOP ioctl instead.
In fact, Michael points out that it looks like busybox's loadfont
program seems to have switched over to using KDFONTOP exactly _because_
of this bug (ahem.. 12 years ago ;-).
Reported-by: Minh Yuan <yuanmingbuaa@gmail.com>
Acked-by: Michael Ellerman <mpe@ellerman.id.au>
Acked-by: Jiri Slaby <jirislaby@kernel.org>
Cc: Greg KH <greg@kroah.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 82e61c3909db51d91b9d3e2071557b6435018b80 upstream.
Both read-side users of func_table/func_buf need locking. Without that,
one can easily confuse the code by repeatedly setting altering strings
like:
while (1)
for (a = 0; a < 2; a++) {
struct kbsentry kbs = {};
strcpy((char *)kbs.kb_string, a ? ".\n" : "88888\n");
ioctl(fd, KDSKBSENT, &kbs);
}
When that program runs, one can get unexpected output by holding F1
(note the unxpected period on the last line):
.
88888
.8888
So protect all accesses to 'func_table' (and func_buf) by preexisting
'func_buf_lock'.
It is easy in 'k_fn' handler as 'puts_queue' is expected not to sleep.
On the other hand, KDGKBSENT needs a local (atomic) copy of the string
because copy_to_user can sleep. Use already allocated, but unused
'kbs->kb_string' for that purpose.
Note that the program above needs at least CAP_SYS_TTY_CONFIG.
This depends on the previous patch and on the func_buf_lock lock added
in commit 46ca3f735f34 (tty/vt: fix write/write race in ioctl(KDSKBSENT)
handler) in 5.2.
Likely fixes CVE-2020-25656.
Cc: <stable@vger.kernel.org>
Reported-by: Minh Yuan <yuanmingbuaa@gmail.com>
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Link: https://lore.kernel.org/r/20201019085517.10176-2-jslaby@suse.cz
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 6ca03f90527e499dd5e32d6522909e2ad390896b upstream.
Use 'strlen' of the string, add one for NUL terminator and simply do
'copy_to_user' instead of the explicit 'for' loop. This makes the
KDGKBSENT case more compact.
The only thing we need to take care about is NULL 'func_table[i]'. Use
an empty string in that case.
The original check for overflow could never trigger as the func_buf
strings are always shorter or equal to 'struct kbsentry's.
Cc: <stable@vger.kernel.org>
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Link: https://lore.kernel.org/r/20201019085517.10176-1-jslaby@suse.cz
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit db332356222d9429731ab9395c89cca403828460 ]
ipwireless_send_packet() can only return 0 on success and -ENOMEM on
error, the caller should check non zero for error condition
Signed-off-by: Tong Zhang <ztong0001@gmail.com>
Acked-by: David Sterba <dsterba@suse.com>
Link: https://lore.kernel.org/r/20200821161942.36589-1-ztong0001@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 71a174b39f10b4b93223d374722aa894b5d8a82e ]
b6da31b2c07c "tty: Fix data race in tty_insert_flip_string_fixed_flag"
puts tty_flip_buffer_push under port->lock introducing the following
possible circular locking dependency:
[30129.876566] ======================================================
[30129.876566] WARNING: possible circular locking dependency detected
[30129.876567] 5.9.0-rc2+ #3 Tainted: G S W
[30129.876568] ------------------------------------------------------
[30129.876568] sysrq.sh/1222 is trying to acquire lock:
[30129.876569] ffffffff92c39480 (console_owner){....}-{0:0}, at: console_unlock+0x3fe/0xa90
[30129.876572] but task is already holding lock:
[30129.876572] ffff888107cb9018 (&pool->lock/1){-.-.}-{2:2}, at: show_workqueue_state.cold.55+0x15b/0x6ca
[30129.876576] which lock already depends on the new lock.
[30129.876577] the existing dependency chain (in reverse order) is:
[30129.876578] -> #3 (&pool->lock/1){-.-.}-{2:2}:
[30129.876581] _raw_spin_lock+0x30/0x70
[30129.876581] __queue_work+0x1a3/0x10f0
[30129.876582] queue_work_on+0x78/0x80
[30129.876582] pty_write+0x165/0x1e0
[30129.876583] n_tty_write+0x47f/0xf00
[30129.876583] tty_write+0x3d6/0x8d0
[30129.876584] vfs_write+0x1a8/0x650
[30129.876588] -> #2 (&port->lock#2){-.-.}-{2:2}:
[30129.876590] _raw_spin_lock_irqsave+0x3b/0x80
[30129.876591] tty_port_tty_get+0x1d/0xb0
[30129.876592] tty_port_default_wakeup+0xb/0x30
[30129.876592] serial8250_tx_chars+0x3d6/0x970
[30129.876593] serial8250_handle_irq.part.12+0x216/0x380
[30129.876593] serial8250_default_handle_irq+0x82/0xe0
[30129.876594] serial8250_interrupt+0xdd/0x1b0
[30129.876595] __handle_irq_event_percpu+0xfc/0x850
[30129.876602] -> #1 (&port->lock){-.-.}-{2:2}:
[30129.876605] _raw_spin_lock_irqsave+0x3b/0x80
[30129.876605] serial8250_console_write+0x12d/0x900
[30129.876606] console_unlock+0x679/0xa90
[30129.876606] register_console+0x371/0x6e0
[30129.876607] univ8250_console_init+0x24/0x27
[30129.876607] console_init+0x2f9/0x45e
[30129.876609] -> #0 (console_owner){....}-{0:0}:
[30129.876611] __lock_acquire+0x2f70/0x4e90
[30129.876612] lock_acquire+0x1ac/0xad0
[30129.876612] console_unlock+0x460/0xa90
[30129.876613] vprintk_emit+0x130/0x420
[30129.876613] printk+0x9f/0xc5
[30129.876614] show_pwq+0x154/0x618
[30129.876615] show_workqueue_state.cold.55+0x193/0x6ca
[30129.876615] __handle_sysrq+0x244/0x460
[30129.876616] write_sysrq_trigger+0x48/0x4a
[30129.876616] proc_reg_write+0x1a6/0x240
[30129.876617] vfs_write+0x1a8/0x650
[30129.876619] other info that might help us debug this:
[30129.876620] Chain exists of:
[30129.876621] console_owner --> &port->lock#2 --> &pool->lock/1
[30129.876625] Possible unsafe locking scenario:
[30129.876626] CPU0 CPU1
[30129.876626] ---- ----
[30129.876627] lock(&pool->lock/1);
[30129.876628] lock(&port->lock#2);
[30129.876630] lock(&pool->lock/1);
[30129.876631] lock(console_owner);
[30129.876633] *** DEADLOCK ***
[30129.876634] 5 locks held by sysrq.sh/1222:
[30129.876634] #0: ffff8881d3ce0470 (sb_writers#3){.+.+}-{0:0}, at: vfs_write+0x359/0x650
[30129.876637] #1: ffffffff92c612c0 (rcu_read_lock){....}-{1:2}, at: __handle_sysrq+0x4d/0x460
[30129.876640] #2: ffffffff92c612c0 (rcu_read_lock){....}-{1:2}, at: show_workqueue_state+0x5/0xf0
[30129.876642] #3: ffff888107cb9018 (&pool->lock/1){-.-.}-{2:2}, at: show_workqueue_state.cold.55+0x15b/0x6ca
[30129.876645] #4: ffffffff92c39980 (console_lock){+.+.}-{0:0}, at: vprintk_emit+0x123/0x420
[30129.876648] stack backtrace:
[30129.876649] CPU: 3 PID: 1222 Comm: sysrq.sh Tainted: G S W 5.9.0-rc2+ #3
[30129.876649] Hardware name: Intel Corporation 2012 Client Platform/Emerald Lake 2, BIOS ACRVMBY1.86C.0078.P00.1201161002 01/16/2012
[30129.876650] Call Trace:
[30129.876650] dump_stack+0x9d/0xe0
[30129.876651] check_noncircular+0x34f/0x410
[30129.876653] __lock_acquire+0x2f70/0x4e90
[30129.876656] lock_acquire+0x1ac/0xad0
[30129.876658] console_unlock+0x460/0xa90
[30129.876660] vprintk_emit+0x130/0x420
[30129.876660] printk+0x9f/0xc5
[30129.876661] show_pwq+0x154/0x618
[30129.876662] show_workqueue_state.cold.55+0x193/0x6ca
[30129.876664] __handle_sysrq+0x244/0x460
[30129.876665] write_sysrq_trigger+0x48/0x4a
[30129.876665] proc_reg_write+0x1a6/0x240
[30129.876666] vfs_write+0x1a8/0x650
It looks like the commit was aimed to protect tty_insert_flip_string and
there is no need for tty_flip_buffer_push to be under this lock.
Fixes: b6da31b2c07c ("tty: Fix data race in tty_insert_flip_string_fixed_flag")
Signed-off-by: Artem Savkov <asavkov@redhat.com>
Acked-by: Jiri Slaby <jirislaby@kernel.org>
Link: https://lore.kernel.org/r/20200902120045.3693075-1-asavkov@redhat.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 63ffcbdad738e3d1c857027789a2273df3337624 ]
The code currently NULLs tty->driver_data in hvcs_close() with the
intent of informing the next call to hvcs_open() that device needs to be
reconfigured. However, when hvcs_cleanup() is called we copy hvcsd from
tty->driver_data which was previoulsy NULLed by hvcs_close() and our
call to tty_port_put(&hvcsd->port) doesn't actually do anything since
&hvcsd->port ends up translating to NULL by chance. This has the side
effect that when hvcs_remove() is called we have one too many port
references preventing hvcs_destuct_port() from ever being called. This
also prevents us from reusing the /dev/hvcsX node in a future
hvcs_probe() and we can eventually run out of /dev/hvcsX devices.
Fix this by waiting to NULL tty->driver_data in hvcs_cleanup().
Fixes: 27bf7c43a19c ("TTY: hvcs, add tty install")
Signed-off-by: Tyrel Datwyler <tyreld@linux.ibm.com>
Link: https://lore.kernel.org/r/20200820234643.70412-1-tyreld@linux.ibm.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 0fb9342d06b0f667b915ba58bfefc030e534a218 ]
parse_options() in drivers/tty/serial/earlycon.c calls uart_parse_earlycon
in drivers/tty/serial/serial_core.c therefore selecting SERIAL_EARLYCON
should automatically select SERIAL_CORE, otherwise will result in symbol
not found error during linking if SERIAL_CORE is not configured as builtin
Fixes: 9aac5887595b ("tty/serial: add generic serial earlycon")
Signed-off-by: Tong Zhang <ztong0001@gmail.com>
Link: https://lore.kernel.org/r/20200828123949.2642-1-ztong0001@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
commit 97293de977365fe672daec2523e66ef457104921 upstream.
* allow NULL consw->con_scrolldelta (some consoles define an empty
hook)
* => remove empty hooks now
* return value of consw->con_scrolldelta is never checked => make the
function void
* document consw->con_scrolldelta a bit
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Cc: Thomas Winischhofer <thomas@winischhofer.net>
Cc: linux-usb@vger.kernel.org
Cc: Jean-Christophe Plagniol-Villard <plagnioj@jcrosoft.com>
Cc: Tomi Valkeinen <tomi.valkeinen@ti.com>
Cc: "James E.J. Bottomley" <jejb@parisc-linux.org>
Cc: Helge Deller <deller@gmx.de>
Cc: linux-fbdev@vger.kernel.org
Cc: linux-parisc@vger.kernel.org
Cc: Ajay Kaher <akaher@vmware.com>
[ for 4.4.y backport, only do the first change above, to prevent
.con_scrolldelta from being called if not present - gregkh]
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit 7d31676a8d91dd18e08853efd1cb26961a38c6a6 ]
Some variants of the samsung tty driver can pick which clock
to use for their baud rate generation. In the DT conversion,
a default clock was selected to be used if a specific one wasn't
assigned and then a comparison of which clock rate worked better
was done. Unfortunately, the comparison was implemented in such
a way that only the default clock was ever actually compared.
Fix this by iterating through all possible clocks, except when a
specific clock has already been picked via clk_sel (which is
only possible via board files).
Signed-off-by: Jonathan Bakker <xc-racer2@live.ca>
Reviewed-by: Krzysztof Kozlowski <krzk@kernel.org>
Link: https://lore.kernel.org/r/BN6PR04MB06604E63833EA41837EBF77BA3A30@BN6PR04MB0660.namprd04.prod.outlook.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
probe
[ Upstream commit 4ce35a3617c0ac758c61122b2218b6c8c9ac9398 ]
When booting j721e the following bug is printed:
[ 1.154821] BUG: sleeping function called from invalid context at kernel/sched/completion.c:99
[ 1.154827] in_atomic(): 0, irqs_disabled(): 128, non_block: 0, pid: 12, name: kworker/0:1
[ 1.154832] 3 locks held by kworker/0:1/12:
[ 1.154836] #0: ffff000840030728 ((wq_completion)events){+.+.}, at: process_one_work+0x1d4/0x6e8
[ 1.154852] #1: ffff80001214fdd8 (deferred_probe_work){+.+.}, at: process_one_work+0x1d4/0x6e8
[ 1.154860] #2: ffff00084060b170 (&dev->mutex){....}, at: __device_attach+0x38/0x138
[ 1.154872] irq event stamp: 63096
[ 1.154881] hardirqs last enabled at (63095): [<ffff800010b74318>] _raw_spin_unlock_irqrestore+0x70/0x78
[ 1.154887] hardirqs last disabled at (63096): [<ffff800010b740d8>] _raw_spin_lock_irqsave+0x28/0x80
[ 1.154893] softirqs last enabled at (62254): [<ffff800010080c88>] _stext+0x488/0x564
[ 1.154899] softirqs last disabled at (62247): [<ffff8000100fdb3c>] irq_exit+0x114/0x140
[ 1.154906] CPU: 0 PID: 12 Comm: kworker/0:1 Not tainted 5.6.0-rc6-next-20200318-00094-g45e4089b0bd3 #221
[ 1.154911] Hardware name: Texas Instruments K3 J721E SoC (DT)
[ 1.154917] Workqueue: events deferred_probe_work_func
[ 1.154923] Call trace:
[ 1.154928] dump_backtrace+0x0/0x190
[ 1.154933] show_stack+0x14/0x20
[ 1.154940] dump_stack+0xe0/0x148
[ 1.154946] ___might_sleep+0x150/0x1f0
[ 1.154952] __might_sleep+0x4c/0x80
[ 1.154957] wait_for_completion_timeout+0x40/0x140
[ 1.154964] ti_sci_set_device_state+0xa0/0x158
[ 1.154969] ti_sci_cmd_get_device_exclusive+0x14/0x20
[ 1.154977] ti_sci_dev_start+0x34/0x50
[ 1.154984] genpd_runtime_resume+0x78/0x1f8
[ 1.154991] __rpm_callback+0x3c/0x140
[ 1.154996] rpm_callback+0x20/0x80
[ 1.155001] rpm_resume+0x568/0x758
[ 1.155007] __pm_runtime_resume+0x44/0xb0
[ 1.155013] omap8250_probe+0x2b4/0x508
[ 1.155019] platform_drv_probe+0x50/0xa0
[ 1.155023] really_probe+0xd4/0x318
[ 1.155028] driver_probe_device+0x54/0xe8
[ 1.155033] __device_attach_driver+0x80/0xb8
[ 1.155039] bus_for_each_drv+0x74/0xc0
[ 1.155044] __device_attach+0xdc/0x138
[ 1.155049] device_initial_probe+0x10/0x18
[ 1.155053] bus_probe_device+0x98/0xa0
[ 1.155058] deferred_probe_work_func+0x74/0xb0
[ 1.155063] process_one_work+0x280/0x6e8
[ 1.155068] worker_thread+0x48/0x430
[ 1.155073] kthread+0x108/0x138
[ 1.155079] ret_from_fork+0x10/0x18
To fix the bug we need to first call pm_runtime_enable() prior to any
pm_runtime calls.
Reported-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Link: https://lore.kernel.org/r/20200320125200.6772-1-peter.ujfalusi@ti.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
commit e0a851fe6b9b619527bd928aa93caaddd003f70c upstream.
If the call to uart_add_one_port() in serial8250_register_8250_port()
fails, a half-initialized entry in the serial_8250ports[] array is left
behind.
A subsequent reprobe of the same serial port causes that entry to be
reused. Because uart->port.dev is set, uart_remove_one_port() is called
for the half-initialized entry and bails out with an error message:
bcm2835-aux-uart 3f215040.serial: Removing wrong port: (null) != (ptrval)
The same happens on failure of mctrl_gpio_init() since commit
4a96895f74c9 ("tty/serial/8250: use mctrl_gpio helpers").
Fix by zeroing the uart->port.dev pointer in the probe error path.
The bug was introduced in v2.6.10 by historical commit befff6f5bf5f
("[SERIAL] Add new port registration/unregistration functions."):
https://git.kernel.org/tglx/history/c/befff6f5bf5f
The commit added an unconditional call to uart_remove_one_port() in
serial8250_register_port(). In v3.7, commit 835d844d1a28 ("8250_pnp:
do pnp probe before legacy probe") made that call conditional on
uart->port.dev which allows me to fix the issue by zeroing that pointer
in the error path. Thus, the present commit will fix the problem as far
back as v3.7 whereas still older versions need to also cherry-pick
835d844d1a28.
Fixes: 835d844d1a28 ("8250_pnp: do pnp probe before legacy probe")
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Cc: stable@vger.kernel.org # v2.6.10
Cc: stable@vger.kernel.org # v2.6.10: 835d844d1a28: 8250_pnp: do pnp probe before legacy
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/b4a072013ee1a1d13ee06b4325afb19bda57ca1b.1589285873.git.lukas@wunner.de
[iwamatsu: Backported to 4.4, 4.9: adjust context]
Signed-off-by: Nobuhiro Iwamatsu (CIP) <nobuhiro1.iwamatsu@toshiba.co.jp>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 3c5a87be170aba8ac40982182f812dcff6ed1ad1 upstream.
These serial ports are exposed by the OOB-management-engine on
RealManage-enabled network cards (e.g. AMD DASH enabled systems using
Realtek cards).
Because these have 3 BARs, they fail the "num_iomem <= 1" check in
serial_pci_guess_board.
I've manually checked the two IOMEM regions and BAR 2 doesn't seem to
respond to reads, but BAR 4 seems to be an MMIO version of the IO ports
(untested).
With this change, the ports are detected:
0000:02:00.1: ttyS0 at I/O 0x2200 (irq = 82, base_baud = 115200) is a 16550A
0000:02:00.2: ttyS1 at I/O 0x2100 (irq = 55, base_baud = 115200) is a 16550A
lspci output:
02:00.1 0700: 10ec:816a (rev 0e) (prog-if 02 [16550])
Subsystem: 17aa:5082
Control: I/O+ Mem+ BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort+ <TAbort- <MAbort- >SERR- <PERR- INTx-
Interrupt: pin B routed to IRQ 82
IOMMU group: 11
Region 0: I/O ports at 2200 [size=256]
Region 2: Memory at fd715000 (64-bit, non-prefetchable) [size=4K]
Region 4: Memory at fd704000 (64-bit, non-prefetchable) [size=16K]
Capabilities: [40] Power Management version 3
Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=375mA PME(D0+,D1+,D2+,D3hot+,D3cold+)
Status: D0 NoSoftRst+ PME-Enable- DSel=0 DScale=0 PME-
Capabilities: [50] MSI: Enable- Count=1/1 Maskable- 64bit+
Address: 0000000000000000 Data: 0000
Capabilities: [70] Express (v2) Endpoint, MSI 01
DevCap: MaxPayload 128 bytes, PhantFunc 0, Latency L0s unlimited, L1 <64us
ExtTag- AttnBtn- AttnInd- PwrInd- RBE+ FLReset- SlotPowerLimit 0.000W
DevCtl: CorrErr- NonFatalErr- FatalErr- UnsupReq-
RlxdOrd+ ExtTag- PhantFunc- AuxPwr- NoSnoop-
MaxPayload 128 bytes, MaxReadReq 512 bytes
DevSta: CorrErr+ NonFatalErr- FatalErr- UnsupReq+ AuxPwr+ TransPend-
LnkCap: Port #0, Speed 2.5GT/s, Width x1, ASPM L0s L1, Exit Latency L0s unlimited, L1 <64us
ClockPM+ Surprise- LLActRep- BwNot- ASPMOptComp+
LnkCtl: ASPM L1 Enabled; RCB 64 bytes, Disabled- CommClk+
ExtSynch- ClockPM- AutWidDis- BWInt- AutBWInt-
LnkSta: Speed 2.5GT/s (ok), Width x1 (ok)
TrErr- Train- SlotClk+ DLActive- BWMgmt- ABWMgmt-
DevCap2: Completion Timeout: Range ABCD, TimeoutDis+ NROPrPrP- LTR+
10BitTagComp- 10BitTagReq- OBFF Via message/WAKE#, ExtFmt- EETLPPrefix-
EmergencyPowerReduction Not Supported, EmergencyPowerReductionInit-
FRS- TPHComp- ExtTPHComp-
AtomicOpsCap: 32bit- 64bit- 128bitCAS-
DevCtl2: Completion Timeout: 50us to 50ms, TimeoutDis- LTR- OBFF Disabled,
AtomicOpsCtl: ReqEn-
LnkSta2: Current De-emphasis Level: -6dB, EqualizationComplete- EqualizationPhase1-
EqualizationPhase2- EqualizationPhase3- LinkEqualizationRequest-
Retimer- 2Retimers- CrosslinkRes: unsupported
Capabilities: [b0] MSI-X: Enable- Count=4 Masked-
Vector table: BAR=4 offset=00000000
PBA: BAR=4 offset=00000800
Capabilities: [d0] Vital Product Data
Not readable
Capabilities: [100 v2] Advanced Error Reporting
UESta: DLP- SDES- TLP- FCP- CmpltTO- CmpltAbrt- UnxCmplt- RxOF- MalfTLP- ECRC- UnsupReq- ACSViol-
UEMsk: DLP- SDES- TLP- FCP- CmpltTO- CmpltAbrt- UnxCmplt- RxOF- MalfTLP- ECRC- UnsupReq- ACSViol-
UESvrt: DLP+ SDES+ TLP- FCP+ CmpltTO- CmpltAbrt- UnxCmplt- RxOF+ MalfTLP+ ECRC- UnsupReq- ACSViol-
CESta: RxErr- BadTLP- BadDLLP- Rollover- Timeout- AdvNonFatalErr+
CEMsk: RxErr- BadTLP- BadDLLP- Rollover- Timeout- AdvNonFatalErr+
AERCap: First Error Pointer: 00, ECRCGenCap+ ECRCGenEn- ECRCChkCap+ ECRCChkEn-
MultHdrRecCap- MultHdrRecEn- TLPPfxPres- HdrLogCap-
HeaderLog: 00000000 00000000 00000000 00000000
Capabilities: [160 v1] Device Serial Number 00-00-00-00-00-00-00-00
Capabilities: [170 v1] Latency Tolerance Reporting
Max snoop latency: 0ns
Max no snoop latency: 0ns
Capabilities: [178 v1] L1 PM Substates
L1SubCap: PCI-PM_L1.2+ PCI-PM_L1.1+ ASPM_L1.2+ ASPM_L1.1+ L1_PM_Substates+
PortCommonModeRestoreTime=150us PortTPowerOnTime=150us
L1SubCtl1: PCI-PM_L1.2- PCI-PM_L1.1- ASPM_L1.2- ASPM_L1.1-
T_CommonMode=0us LTR1.2_Threshold=0ns
L1SubCtl2: T_PwrOn=10us
02:00.2 0700: 10ec:816b (rev 0e)
[...same...]
Signed-off-by: Tobias Diedrich <tobiasdiedrich@gmail.com>
Cc: stable <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20200914173628.GA22508@yamamaya.is-a-geek.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 205d300aea75623e1ae4aa43e0d265ab9cf195fd upstream.
We have a number of "uart.port->desc.lock vs desc.lock->uart.port"
lockdep reports coming from 8250 driver; this causes a bit of trouble
to people, so let's fix it.
The problem is reverse lock order in two different call paths:
chain #1:
serial8250_do_startup()
spin_lock_irqsave(&port->lock);
disable_irq_nosync(port->irq);
raw_spin_lock_irqsave(&desc->lock)
chain #2:
__report_bad_irq()
raw_spin_lock_irqsave(&desc->lock)
for_each_action_of_desc()
printk()
spin_lock_irqsave(&port->lock);
Fix this by changing the order of locks in serial8250_do_startup():
do disable_irq_nosync() first, which grabs desc->lock, and grab
uart->port after that, so that chain #1 and chain #2 have same lock
order.
Full lockdep splat:
======================================================
WARNING: possible circular locking dependency detected
5.4.39 #55 Not tainted
======================================================
swapper/0/0 is trying to acquire lock:
ffffffffab65b6c0 (console_owner){-...}, at: console_lock_spinning_enable+0x31/0x57
but task is already holding lock:
ffff88810a8e34c0 (&irq_desc_lock_class){-.-.}, at: __report_bad_irq+0x5b/0xba
which lock already depends on the new lock.
the existing dependency chain (in reverse order) is:
-> #2 (&irq_desc_lock_class){-.-.}:
_raw_spin_lock_irqsave+0x61/0x8d
__irq_get_desc_lock+0x65/0x89
__disable_irq_nosync+0x3b/0x93
serial8250_do_startup+0x451/0x75c
uart_startup+0x1b4/0x2ff
uart_port_activate+0x73/0xa0
tty_port_open+0xae/0x10a
uart_open+0x1b/0x26
tty_open+0x24d/0x3a0
chrdev_open+0xd5/0x1cc
do_dentry_open+0x299/0x3c8
path_openat+0x434/0x1100
do_filp_open+0x9b/0x10a
do_sys_open+0x15f/0x3d7
kernel_init_freeable+0x157/0x1dd
kernel_init+0xe/0x105
ret_from_fork+0x27/0x50
-> #1 (&port_lock_key){-.-.}:
_raw_spin_lock_irqsave+0x61/0x8d
serial8250_console_write+0xa7/0x2a0
console_unlock+0x3b7/0x528
vprintk_emit+0x111/0x17f
printk+0x59/0x73
register_console+0x336/0x3a4
uart_add_one_port+0x51b/0x5be
serial8250_register_8250_port+0x454/0x55e
dw8250_probe+0x4dc/0x5b9
platform_drv_probe+0x67/0x8b
really_probe+0x14a/0x422
driver_probe_device+0x66/0x130
device_driver_attach+0x42/0x5b
__driver_attach+0xca/0x139
bus_for_each_dev+0x97/0xc9
bus_add_driver+0x12b/0x228
driver_register+0x64/0xed
do_one_initcall+0x20c/0x4a6
do_initcall_level+0xb5/0xc5
do_basic_setup+0x4c/0x58
kernel_init_freeable+0x13f/0x1dd
kernel_init+0xe/0x105
ret_from_fork+0x27/0x50
-> #0 (console_owner){-...}:
__lock_acquire+0x118d/0x2714
lock_acquire+0x203/0x258
console_lock_spinning_enable+0x51/0x57
console_unlock+0x25d/0x528
vprintk_emit+0x111/0x17f
printk+0x59/0x73
__report_bad_irq+0xa3/0xba
note_interrupt+0x19a/0x1d6
handle_irq_event_percpu+0x57/0x79
handle_irq_event+0x36/0x55
handle_fasteoi_irq+0xc2/0x18a
do_IRQ+0xb3/0x157
ret_from_intr+0x0/0x1d
cpuidle_enter_state+0x12f/0x1fd
cpuidle_enter+0x2e/0x3d
do_idle+0x1ce/0x2ce
cpu_startup_entry+0x1d/0x1f
start_kernel+0x406/0x46a
secondary_startup_64+0xa4/0xb0
other info that might help us debug this:
Chain exists of:
console_owner --> &port_lock_key --> &irq_desc_lock_class
Possible unsafe locking scenario:
CPU0 CPU1
---- ----
lock(&irq_desc_lock_class);
lock(&port_lock_key);
lock(&irq_desc_lock_class);
lock(console_owner);
*** DEADLOCK ***
2 locks held by swapper/0/0:
#0: ffff88810a8e34c0 (&irq_desc_lock_class){-.-.}, at: __report_bad_irq+0x5b/0xba
#1: ffffffffab65b5c0 (console_lock){+.+.}, at: console_trylock_spinning+0x20/0x181
stack backtrace:
CPU: 0 PID: 0 Comm: swapper/0 Not tainted 5.4.39 #55
Hardware name: XXXXXX
Call Trace:
<IRQ>
dump_stack+0xbf/0x133
? print_circular_bug+0xd6/0xe9
check_noncircular+0x1b9/0x1c3
__lock_acquire+0x118d/0x2714
lock_acquire+0x203/0x258
? console_lock_spinning_enable+0x31/0x57
console_lock_spinning_enable+0x51/0x57
? console_lock_spinning_enable+0x31/0x57
console_unlock+0x25d/0x528
? console_trylock+0x18/0x4e
vprintk_emit+0x111/0x17f
? lock_acquire+0x203/0x258
printk+0x59/0x73
__report_bad_irq+0xa3/0xba
note_interrupt+0x19a/0x1d6
handle_irq_event_percpu+0x57/0x79
handle_irq_event+0x36/0x55
handle_fasteoi_irq+0xc2/0x18a
do_IRQ+0xb3/0x157
common_interrupt+0xf/0xf
</IRQ>
Signed-off-by: Sergey Senozhatsky <sergey.senozhatsky@gmail.com>
Fixes: 768aec0b5bcc ("serial: 8250: fix shared interrupts issues with SMP and RT kernels")
Reported-by: Guenter Roeck <linux@roeck-us.net>
Reported-by: Raul Rangel <rrangel@google.com>
BugLink: https://bugs.chromium.org/p/chromium/issues/detail?id=1114800
Link: https://lore.kernel.org/lkml/CAHQZ30BnfX+gxjPm1DUd5psOTqbyDh4EJE=2=VAMW_VDafctkA@mail.gmail.com/T/#u
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Tested-by: Guenter Roeck <linux@roeck-us.net>
Cc: stable <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20200817022646.1484638-1-sergey.senozhatsky@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 89efbe70b27dd325d8a8c177743a26b885f7faec upstream.
pl011_probe() calls pl011_setup_port() to reserve an amba_ports[] entry,
then calls pl011_register_port() to register the uart driver with the
tty layer.
If registration of the uart driver fails, the amba_ports[] entry is not
released. If this happens 14 times (value of UART_NR macro), then all
amba_ports[] entries will have been leaked and driver probing is no
longer possible. (To be fair, that can only happen if the DeviceTree
doesn't contain alias IDs since they cause the same entry to be used for
a given port.) Fix it.
Fixes: ef2889f7ffee ("serial: pl011: Move uart_register_driver call to device")
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Cc: stable@vger.kernel.org # v3.15+
Cc: Tushar Behera <tushar.behera@linaro.org>
Link: https://lore.kernel.org/r/138f8c15afb2f184d8102583f8301575566064a6.1597316167.git.lukas@wunner.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 8c6c378b0cbe0c9f1390986b5f8ffb5f6ff7593b upstream.
In few older Samsung SoCs like s3c2410, s3c2412
and s3c2440, UART IP is having 2 interrupt lines.
However, in other SoCs like s3c6400, s5pv210,
exynos5433, and exynos4210 UART is having only 1
interrupt line. Due to this, "platform_get_irq(platdev, 1)"
call in the driver gives the following false-positive error:
"IRQ index 1 not found" on newer SoC's.
This patch adds the condition to check for Tx interrupt
only for the those SoC's which have 2 interrupt lines.
Tested-by: Alim Akhtar <alim.akhtar@samsung.com>
Tested-by: Marek Szyprowski <m.szyprowski@samsung.com>
Reviewed-by: Krzysztof Kozlowski <krzk@kernel.org>
Reviewed-by: Alim Akhtar <alim.akhtar@samsung.com>
Signed-off-by: Tamseel Shams <m.shams@samsung.com>
Cc: stable <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20200810030021.45348-1-m.shams@samsung.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit bc5269ca765057a1b762e79a1cfd267cd7bf1c46 upstream.
vc_resize() can return with an error after failure. Change VT_RESIZEX ioctl
to save struct vc_data values that are modified and restore the original
values in case of error.
Signed-off-by: George Kennedy <george.kennedy@oracle.com>
Cc: stable <stable@vger.kernel.org>
Reported-by: syzbot+38a3699c7eaf165b97a6@syzkaller.appspotmail.com
Link: https://lore.kernel.org/r/1596213192-6635-2-git-send-email-george.kennedy@oracle.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit f8d1653daec02315e06d30246cff4af72e76e54e upstream.
syzbot is reporting UAF bug in set_origin() from vc_do_resize() [1], for
vc_do_resize() calls kfree(vc->vc_screenbuf) before calling set_origin().
Unfortunately, in set_origin(), vc->vc_sw->con_set_origin() might access
vc->vc_pos when scroll is involved in order to manipulate cursor, but
vc->vc_pos refers already released vc->vc_screenbuf until vc->vc_pos gets
updated based on the result of vc->vc_sw->con_set_origin().
Preserving old buffer and tolerating outdated vc members until set_origin()
completes would be easier than preventing vc->vc_sw->con_set_origin() from
accessing outdated vc members.
[1] https://syzkaller.appspot.com/bug?id=6649da2081e2ebdc65c0642c214b27fe91099db3
Reported-by: syzbot <syzbot+9116ecc1978ca3a12f43@syzkaller.appspotmail.com>
Signed-off-by: Tetsuo Handa <penguin-kernel@I-love.SAKURA.ne.jp>
Cc: stable <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/1596034621-4714-1-git-send-email-penguin-kernel@I-love.SAKURA.ne.jp
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 551e553f0d4ab623e2a6f424ab5834f9c7b5229c upstream.
Commit 7b668c064ec3 ("serial: 8250: Fix max baud limit in generic 8250
port") fixed limits of a baud rate setting for a generic 8250 port.
In other words since that commit the baud rate has been permitted to be
within [uartclk / 16 / UART_DIV_MAX; uartclk / 16], which is absolutely
normal for a standard 8250 UART port. But there are custom 8250 ports,
which provide extended baud rate limits. In particular the Mediatek 8250
port can work with baud rates up to "uartclk" speed.
Normally that and any other peculiarity is supposed to be handled in a
custom set_termios() callback implemented in the vendor-specific
8250-port glue-driver. Currently that is how it's done for the most of
the vendor-specific 8250 ports, but for some reason for Mediatek a
solution has been spread out to both the glue-driver and to the generic
8250-port code. Due to that a bug has been introduced, which permitted the
extended baud rate limit for all even for standard 8250-ports. The bug
has been fixed by the commit 7b668c064ec3 ("serial: 8250: Fix max baud
limit in generic 8250 port") by narrowing the baud rates limit back down to
the normal bounds. Unfortunately by doing so we also broke the
Mediatek-specific extended bauds feature.
A fix of the problem described above is twofold. First since we can't get
back the extended baud rate limits feature to the generic set_termios()
function and that method supports only a standard baud rates range, the
requested baud rate must be locally stored before calling it and then
restored back to the new termios structure after the generic set_termios()
finished its magic business. By doing so we still use the
serial8250_do_set_termios() method to set the LCR/MCR/FCR/etc. registers,
while the extended baud rate setting procedure will be performed later in
the custom Mediatek-specific set_termios() callback. Second since a true
baud rate is now fully calculated in the custom set_termios() method we
need to locally update the port timeout by calling the
uart_update_timeout() function. After the fixes described above are
implemented in the 8250_mtk.c driver, the Mediatek 8250-port should
get back to normally working with extended baud rates.
Link: https://lore.kernel.org/linux-serial/20200701211337.3027448-1-danielwinkler@google.com
Fixes: 7b668c064ec3 ("serial: 8250: Fix max baud limit in generic 8250 port")
Reported-by: Daniel Winkler <danielwinkler@google.com>
Signed-off-by: Serge Semin <Sergey.Semin@baikalelectronics.ru>
Cc: stable <stable@vger.kernel.org>
Tested-by: Claire Chang <tientzu@chromium.org>
Link: https://lore.kernel.org/r/20200714124113.20918-1-Sergey.Semin@baikalelectronics.ru
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit f4c23a140d80ef5e6d3d1f8f57007649014b60fa upstream.
I got null-ptr-deref in serial8250_start_tx():
[ 78.114630] Unable to handle kernel NULL pointer dereference at virtual address 0000000000000000
[ 78.123778] Mem abort info:
[ 78.126560] ESR = 0x86000007
[ 78.129603] EC = 0x21: IABT (current EL), IL = 32 bits
[ 78.134891] SET = 0, FnV = 0
[ 78.137933] EA = 0, S1PTW = 0
[ 78.141064] user pgtable: 64k pages, 48-bit VAs, pgdp=00000027d41a8600
[ 78.147562] [0000000000000000] pgd=00000027893f0003, p4d=00000027893f0003, pud=00000027893f0003, pmd=00000027c9a20003, pte=0000000000000000
[ 78.160029] Internal error: Oops: 86000007 [#1] SMP
[ 78.164886] Modules linked in: sunrpc vfat fat aes_ce_blk crypto_simd cryptd aes_ce_cipher crct10dif_ce ghash_ce sha2_ce sha256_arm64 sha1_ce ses enclosure sg sbsa_gwdt ipmi_ssif spi_dw_mmio sch_fq_codel vhost_net tun vhost vhost_iotlb tap ip_tables ext4 mbcache jbd2 ahci hisi_sas_v3_hw libahci hisi_sas_main libsas hns3 scsi_transport_sas hclge libata megaraid_sas ipmi_si hnae3 ipmi_devintf ipmi_msghandler br_netfilter bridge stp llc nvme nvme_core xt_sctp sctp libcrc32c dm_mod nbd
[ 78.207383] CPU: 11 PID: 23258 Comm: null-ptr Not tainted 5.8.0-rc6+ #48
[ 78.214056] Hardware name: Huawei TaiShan 2280 V2/BC82AMDC, BIOS 2280-V2 CS V3.B210.01 03/12/2020
[ 78.222888] pstate: 80400089 (Nzcv daIf +PAN -UAO BTYPE=--)
[ 78.228435] pc : 0x0
[ 78.230618] lr : serial8250_start_tx+0x160/0x260
[ 78.235215] sp : ffff800062eefb80
[ 78.238517] x29: ffff800062eefb80 x28: 0000000000000fff
[ 78.243807] x27: ffff800062eefd80 x26: ffff202fd83b3000
[ 78.249098] x25: ffff800062eefd80 x24: ffff202fd83b3000
[ 78.254388] x23: ffff002fc5e50be8 x22: 0000000000000002
[ 78.259679] x21: 0000000000000001 x20: 0000000000000000
[ 78.264969] x19: ffffa688827eecc8 x18: 0000000000000000
[ 78.270259] x17: 0000000000000000 x16: 0000000000000000
[ 78.275550] x15: ffffa68881bc67a8 x14: 00000000000002e6
[ 78.280841] x13: ffffa68881bc67a8 x12: 000000000000c539
[ 78.286131] x11: d37a6f4de9bd37a7 x10: ffffa68881cccff0
[ 78.291421] x9 : ffffa68881bc6000 x8 : ffffa688819daa88
[ 78.296711] x7 : ffffa688822a0f20 x6 : ffffa688819e0000
[ 78.302002] x5 : ffff800062eef9d0 x4 : ffffa68881e707a8
[ 78.307292] x3 : 0000000000000000 x2 : 0000000000000002
[ 78.312582] x1 : 0000000000000001 x0 : ffffa688827eecc8
[ 78.317873] Call trace:
[ 78.320312] 0x0
[ 78.322147] __uart_start.isra.9+0x64/0x78
[ 78.326229] uart_start+0xb8/0x1c8
[ 78.329620] uart_flush_chars+0x24/0x30
[ 78.333442] n_tty_receive_buf_common+0x7b0/0xc30
[ 78.338128] n_tty_receive_buf+0x44/0x2c8
[ 78.342122] tty_ioctl+0x348/0x11f8
[ 78.345599] ksys_ioctl+0xd8/0xf8
[ 78.348903] __arm64_sys_ioctl+0x2c/0xc8
[ 78.352812] el0_svc_common.constprop.2+0x88/0x1b0
[ 78.357583] do_el0_svc+0x44/0xd0
[ 78.360887] el0_sync_handler+0x14c/0x1d0
[ 78.364880] el0_sync+0x140/0x180
[ 78.368185] Code: bad PC value
SERIAL_PORT_DFNS is not defined on each arch, if it's not defined,
serial8250_set_defaults() won't be called in serial8250_isa_init_ports(),
so the p->serial_in pointer won't be initialized, and it leads a null-ptr-deref.
Fix this problem by calling serial8250_set_defaults() after init uart port.
Signed-off-by: Yang Yingliang <yangyingliang@huawei.com>
Cc: stable <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20200721143852.4058352-1-yangyingliang@huawei.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit 4dd31f1ffec6c370c3c2e0c605628bf5e16d5c46 ]
When submitting the previous fix "tty: n_gsm: Fix waking up upper tty
layer when room available". It was suggested to switch from a while to
a for loop, but when doing it, there was a remaining bogus i++.
This patch removes this i++ and also reorganizes the code making it more
compact.
Fixes: e1eaea46bb40 ("tty: n_gsm line discipline")
Signed-off-by: Gregory CLEMENT <gregory.clement@bootlin.com>
Link: https://lore.kernel.org/r/20200518084517.2173242-3-gregory.clement@bootlin.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 01dbb362f0a114fbce19c8abe4cd6f4710e934d5 ]
Warn the upper layer when n_gms is ready to receive data
again. Without this the associated virtual tty remains blocked
indefinitely.
Fixes: e1eaea46bb40 ("tty: n_gsm line discipline")
Signed-off-by: Gregory CLEMENT <gregory.clement@bootlin.com>
Link: https://lore.kernel.org/r/20200512115323.1447922-4-gregory.clement@bootlin.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 84d6f81c1fb58b56eba81ff0a36cf31946064b40 ]
For at least some modems like the TELIT LE910, skipping SOF makes
transfers blocking indefinitely after a short amount of data
transferred.
Given the small improvement provided by skipping the SOF (just one
byte on about 100 bytes), it seems better to completely remove this
"feature" than make it optional.
Fixes: e1eaea46bb40 ("tty: n_gsm line discipline")
Signed-off-by: Gregory CLEMENT <gregory.clement@bootlin.com>
Link: https://lore.kernel.org/r/20200512115323.1447922-3-gregory.clement@bootlin.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 8508f4cba308f785b2fd4b8c38849c117b407297 ]
Valentine reported seeing:
[ 3.626638] INFO: trying to register non-static key.
[ 3.626639] the code is fine but needs lockdep annotation.
[ 3.626640] turning off the locking correctness validator.
[ 3.626644] CPU: 7 PID: 51 Comm: kworker/7:1 Not tainted 5.7.0-rc2-00115-g8c2e9790f196 #116
[ 3.626646] Hardware name: HiKey960 (DT)
[ 3.626656] Workqueue: events deferred_probe_work_func
[ 3.632476] sd 0:0:0:0: [sda] Optimal transfer size 8192 bytes not a multiple of physical block size (16384 bytes)
[ 3.640220] Call trace:
[ 3.640225] dump_backtrace+0x0/0x1b8
[ 3.640227] show_stack+0x20/0x30
[ 3.640230] dump_stack+0xec/0x158
[ 3.640234] register_lock_class+0x598/0x5c0
[ 3.640235] __lock_acquire+0x80/0x16c0
[ 3.640236] lock_acquire+0xf4/0x4a0
[ 3.640241] _raw_spin_lock_irqsave+0x70/0xa8
[ 3.640245] uart_add_one_port+0x388/0x4b8
[ 3.640248] pl011_register_port+0x70/0xf0
[ 3.640250] pl011_probe+0x184/0x1b8
[ 3.640254] amba_probe+0xdc/0x180
[ 3.640256] really_probe+0xe0/0x338
[ 3.640257] driver_probe_device+0x60/0xf8
[ 3.640259] __device_attach_driver+0x8c/0xd0
[ 3.640260] bus_for_each_drv+0x84/0xd8
[ 3.640261] __device_attach+0xe4/0x140
[ 3.640263] device_initial_probe+0x1c/0x28
[ 3.640265] bus_probe_device+0xa4/0xb0
[ 3.640266] deferred_probe_work_func+0x7c/0xb8
[ 3.640269] process_one_work+0x2c0/0x768
[ 3.640271] worker_thread+0x4c/0x498
[ 3.640272] kthread+0x14c/0x158
[ 3.640275] ret_from_fork+0x10/0x1c
Which seems to be due to the fact that after allocating the uap
structure, nothing initializes the spinlock.
Its a little confusing, as uart_port_spin_lock_init() is one
place where the lock is supposed to be initialized, but it has
an exception for the case where the port is a console.
This makes it seem like a deeper fix is needed to properly
register the console, but I'm not sure what that entails, and
Andy suggested that this approach is less invasive.
Thus, this patch resolves the issue by initializing the spinlock
in the driver, and resolves the resulting warning.
Cc: Andy Shevchenko <andy.shevchenko@gmail.com>
Cc: Russell King <linux@armlinux.org.uk>
Cc: Jiri Slaby <jslaby@suse.com>
Cc: linux-serial@vger.kernel.org
Reported-by: Valentin Schneider <valentin.schneider@arm.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: John Stultz <john.stultz@linaro.org>
Reviewed-and-tested-by: Valentin Schneider <valentin.schneider@arm.com>
Link: https://lore.kernel.org/r/20200428184050.6501-1-john.stultz@linaro.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit e2bd1dcbe1aa34ff5570b3427c530e4332ecf0fe ]
Potentially, hvc_open() can be called in parallel when two tasks calls
open() on /dev/hvcX. In such a scenario, if the hp->ops->notifier_add()
callback in the function fails, where it sets the tty->driver_data to
NULL, the parallel hvc_open() can see this NULL and cause a memory abort.
Hence, serialize hvc_open and check if tty->private_data is NULL before
proceeding ahead.
The issue can be easily reproduced by launching two tasks simultaneously
that does nothing but open() and close() on /dev/hvcX.
For example:
$ ./simple_open_close /dev/hvc0 & ./simple_open_close /dev/hvc0 &
Signed-off-by: Raghavendra Rao Ananta <rananta@codeaurora.org>
Link: https://lore.kernel.org/r/20200428032601.22127-1-rananta@codeaurora.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
commit b86dab054059b970111b5516ae548efaae5b3aae upstream.
When k_ascii is invoked several times in a row there is a potential for
signed integer overflow:
UBSAN: Undefined behaviour in drivers/tty/vt/keyboard.c:888:19 signed integer overflow:
10 * 1111111111 cannot be represented in type 'int'
CPU: 0 PID: 0 Comm: swapper/0 Not tainted 5.6.11 #1
Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS Bochs 01/01/2011
Call Trace:
<IRQ>
__dump_stack lib/dump_stack.c:77 [inline]
dump_stack+0xce/0x128 lib/dump_stack.c:118
ubsan_epilogue+0xe/0x30 lib/ubsan.c:154
handle_overflow+0xdc/0xf0 lib/ubsan.c:184
__ubsan_handle_mul_overflow+0x2a/0x40 lib/ubsan.c:205
k_ascii+0xbf/0xd0 drivers/tty/vt/keyboard.c:888
kbd_keycode drivers/tty/vt/keyboard.c:1477 [inline]
kbd_event+0x888/0x3be0 drivers/tty/vt/keyboard.c:1495
While it can be worked around by using check_mul_overflow()/
check_add_overflow(), it is better to introduce a separate flag to
signal that number pad is being used to compose a symbol, and
change type of the accumulator from signed to unsigned, thus
avoiding undefined behavior when it overflows.
Reported-by: Kyungtae Kim <kt0755@gmail.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Cc: stable <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20200525232740.GA262061@dtor-ws
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit e00164a0f000de893944981f41a568c981aca658 upstream.
err_spi is used when SERIAL_SC16IS7XX_SPI is enabled, so make
the label only available under SERIAL_SC16IS7XX_SPI option.
Otherwise, the below warning appears.
drivers/tty/serial/sc16is7xx.c:1523:1: warning: label ‘err_spi’ defined but not used [-Wunused-label]
err_spi:
^~~~~~~
Signed-off-by: Guoqing Jiang <gqjiang@suse.com>
Fixes: ac0cdb3d9901 ("sc16is7xx: missing unregister/delete driver on error in sc16is7xx_init()")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Cc: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 926b7b5122c96e1f18cd20e85a286c7ec8d18c97 upstream.
On non-DeviceTree platforms, the index of serial device is a static
variable incremented on each probe. It is incremented even if deferred
probe happens when getting the clock in s3c24xx_serial_init_port().
This index is used for referencing elements of statically allocated
s3c24xx_serial_ports array. In case of re-probe, the index will point
outside of this array leading to memory corruption.
Increment the index only on successful probe.
Reported-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
Fixes: b497549a035c ("[ARM] S3C24XX: Split serial driver into core and per-cpu drivers")
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 98952bf510d0c7cdfc284f098bbf4682dc47bc61 upstream.
The msm_find_best_baud() function is written with the assumption
that the port->uartclk rate is fixed to a particular rate at boot
time, but now this driver changes that clk rate at runtime when
the baud is changed.
The way the hardware works is that an input clk rate comes from
the clk controller into the uart hw block. That rate is typically
1843200 or 3686400 Hz. That rate can then be divided by an
internal divider in the hw block to achieve a particular baud on
the serial wire. msm_find_best_baud() is looking for that divider
value.
A few things are wrong with the way the code is written. First,
it assumes that the maximum baud that the uart can support if the
clk rate is fixed at boot is 460800, which would correspond to an
input clk rate of 230400 * 16 == 3686400 Hz. Except some devices
have a boot rate of 1843200 Hz or max baud of 115200, so
achieving 230400 on those devices doesn't work at all because we
don't increase the clk rate unless max baud is 460800.
Second, we can't achieve bauds higher than 460800 that require
anything besides a divisor of 1, because we always call
msm_find_best_baud() with a fixed port->uartclk rate that will
eventually be changed after we calculate the divisor. So if we
need to get a baud of 500000, we'll just multiply that by 16 and
hope that the clk can give us 500000 * 16 == 8000000 Hz, which it
typically can't do. To really achieve 500000 baud, we need to get
an input clk rate of 24000000 Hz and then divide that by 3 inside
the uart hardware.
Finally, we return success for bauds even when we can't actually
achieve them. This means that when the user asks for 500000 baud,
we actually get 921600 right now, but the user doesn't know that.
Fix all of this by searching through the divisor and clk rate
space with a combination of clk_round_rate() and baud
calculations, keeping track of the best clk rate and divisor we
find if we can't get an exact match. Typically we can get an
exact match with a divisor of 1, but sometimes we need to keep
track and try more frequencies. On my msm8916 device, this
results in all standard bauds in baud_table being supported
except for 1800, 576000, 1152000, and 4000000.
Fixes: 850b37a71bde ("tty: serial: msm: Remove 115.2 Kbps maximum baud rate limitation")
Cc: "Ivan T. Ivanov" <iivanov.xz@gmail.com>
Cc: Matthew McClintock <mmcclint@codeaurora.org>
Signed-off-by: Stephen Boyd <stephen.boyd@linaro.org>
Tested-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Acked-by: Andy Gross <andy.gross@linaro.org>
Acked-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Tested-by: Cristian Prundeanu <cprundea@codeaurora.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 7127d24372bf23675a36edc64d092dc7fd92ebe8 upstream.
init_r_port can access pc104 array out of bounds. pc104 is a 2D array
defined to have 4 members. Each member has 8 submembers.
* we can have more than 4 (PCI) boards, i.e. [board] can be OOB
* line is not modulo-ed by anything, so the first line on the second
board can be 4, on the 3rd 12 or alike (depending on previously
registered boards). It's zero only on the first line of the first
board. So even [line] can be OOB, quite soon (with the 2nd registered
board already).
This code is broken for ages, so just avoid the OOB accesses and don't
try to fix it as we would need to find out the correct line number. Use
the default: RS232, if we are out.
Generally, if anyone needs to set the interface types, a module parameter
is past the last thing that should be used for this purpose. The
parameters' description says it's for ISA cards anyway.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Cc: stable <stable@vger.kernel.org>
Fixes: 1da177e4c3f4 ("Linux-2.6.12-rc2")
Link: https://lore.kernel.org/r/20200417105959.15201-2-jslaby@suse.cz
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 9a9fc42b86c06120744555fea43fdcabe297c656 upstream.
If there is a lot(more then 16) of virtio-console devices
or virtio_console module is reloaded
- buffers 'vtermnos' and 'cons_ops' are overflowed.
In older kernels it overruns spinlock which leads to kernel freezing:
https://bugzilla.redhat.com/show_bug.cgi?id=1786239
To reproduce the issue, you can try simple script that
loads/unloads module. Something like this:
while [ 1 ]
do
modprobe virtio_console
sleep 2
modprobe -r virtio_console
sleep 2
done
Description of problem:
Guest get 'Call Trace' when loading module "virtio_console"
and unloading it frequently - clearly reproduced on kernel-4.18.0:
[ 81.498208] ------------[ cut here ]------------
[ 81.499263] pvqspinlock: lock 0xffffffff92080020 has corrupted value 0xc0774ca0!
[ 81.501000] WARNING: CPU: 0 PID: 785 at kernel/locking/qspinlock_paravirt.h:500 __pv_queued_spin_unlock_slowpath+0xc0/0xd0
[ 81.503173] Modules linked in: virtio_console fuse xt_CHECKSUM ipt_MASQUERADE xt_conntrack ipt_REJECT nft_counter nf_nat_tftp nft_objref nf_conntrack_tftp tun bridge stp llc nft_fib_inet nft_fib_ipv4 nft_fib_ipv6 nft_fib nft_reject_inet nf_reject_ipv4 nf_reject_ipv6 nft_reject nft_ct nf_tables_set nft_chain_nat_ipv6 nf_conntrack_ipv6 nf_defrag_ipv6 nf_nat_ipv6 nft_chain_route_ipv6 nft_chain_nat_ipv4 nf_conntrack_ipv4 nf_defrag_ipv4 nf_nat_ipv4 nf_nat nf_conntrack nft_chain_route_ipv4 ip6_tables nft_compat ip_set nf_tables nfnetlink sunrpc bochs_drm drm_vram_helper ttm drm_kms_helper syscopyarea sysfillrect sysimgblt fb_sys_fops drm i2c_piix4 pcspkr crct10dif_pclmul crc32_pclmul joydev ghash_clmulni_intel ip_tables xfs libcrc32c sd_mod sg ata_generic ata_piix virtio_net libata crc32c_intel net_failover failover serio_raw virtio_scsi dm_mirror dm_region_hash dm_log dm_mod [last unloaded: virtio_console]
[ 81.517019] CPU: 0 PID: 785 Comm: kworker/0:2 Kdump: loaded Not tainted 4.18.0-167.el8.x86_64 #1
[ 81.518639] Hardware name: Red Hat KVM, BIOS 1.12.0-5.scrmod+el8.2.0+5159+d8aa4d83 04/01/2014
[ 81.520205] Workqueue: events control_work_handler [virtio_console]
[ 81.521354] RIP: 0010:__pv_queued_spin_unlock_slowpath+0xc0/0xd0
[ 81.522450] Code: 07 00 48 63 7a 10 e8 bf 64 f5 ff 66 90 c3 8b 05 e6 cf d6 01 85 c0 74 01 c3 8b 17 48 89 fe 48 c7 c7 38 4b 29 91 e8 3a 6c fa ff <0f> 0b c3 0f 0b 90 90 90 90 90 90 90 90 90 90 90 0f 1f 44 00 00 48
[ 81.525830] RSP: 0018:ffffb51a01ffbd70 EFLAGS: 00010282
[ 81.526798] RAX: 0000000000000000 RBX: 0000000000000010 RCX: 0000000000000000
[ 81.528110] RDX: ffff9e66f1826480 RSI: ffff9e66f1816a08 RDI: ffff9e66f1816a08
[ 81.529437] RBP: ffffffff9153ff10 R08: 000000000000026c R09: 0000000000000053
[ 81.530732] R10: 0000000000000000 R11: ffffb51a01ffbc18 R12: ffff9e66cd682200
[ 81.532133] R13: ffffffff9153ff10 R14: ffff9e6685569500 R15: ffff9e66cd682000
[ 81.533442] FS: 0000000000000000(0000) GS:ffff9e66f1800000(0000) knlGS:0000000000000000
[ 81.534914] CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033
[ 81.535971] CR2: 00005624c55b14d0 CR3: 00000003a023c000 CR4: 00000000003406f0
[ 81.537283] Call Trace:
[ 81.537763] __raw_callee_save___pv_queued_spin_unlock_slowpath+0x11/0x20
[ 81.539011] .slowpath+0x9/0xe
[ 81.539585] hvc_alloc+0x25e/0x300
[ 81.540237] init_port_console+0x28/0x100 [virtio_console]
[ 81.541251] handle_control_message.constprop.27+0x1c4/0x310 [virtio_console]
[ 81.542546] control_work_handler+0x70/0x10c [virtio_console]
[ 81.543601] process_one_work+0x1a7/0x3b0
[ 81.544356] worker_thread+0x30/0x390
[ 81.545025] ? create_worker+0x1a0/0x1a0
[ 81.545749] kthread+0x112/0x130
[ 81.546358] ? kthread_flush_work_fn+0x10/0x10
[ 81.547183] ret_from_fork+0x22/0x40
[ 81.547842] ---[ end trace aa97649bd16c8655 ]---
[ 83.546539] general protection fault: 0000 [#1] SMP NOPTI
[ 83.547422] CPU: 5 PID: 3225 Comm: modprobe Kdump: loaded Tainted: G W --------- - - 4.18.0-167.el8.x86_64 #1
[ 83.549191] Hardware name: Red Hat KVM, BIOS 1.12.0-5.scrmod+el8.2.0+5159+d8aa4d83 04/01/2014
[ 83.550544] RIP: 0010:__pv_queued_spin_lock_slowpath+0x19a/0x2a0
[ 83.551504] Code: c4 c1 ea 12 41 be 01 00 00 00 4c 8d 6d 14 41 83 e4 03 8d 42 ff 49 c1 e4 05 48 98 49 81 c4 40 a5 02 00 4c 03 24 c5 60 48 34 91 <49> 89 2c 24 b8 00 80 00 00 eb 15 84 c0 75 0a 41 0f b6 54 24 14 84
[ 83.554449] RSP: 0018:ffffb51a0323fdb0 EFLAGS: 00010202
[ 83.555290] RAX: 000000000000301c RBX: ffffffff92080020 RCX: 0000000000000001
[ 83.556426] RDX: 000000000000301d RSI: 0000000000000000 RDI: 0000000000000000
[ 83.557556] RBP: ffff9e66f196a540 R08: 000000000000028a R09: ffff9e66d2757788
[ 83.558688] R10: 0000000000000000 R11: 0000000000000000 R12: 646e61725f770b07
[ 83.559821] R13: ffff9e66f196a554 R14: 0000000000000001 R15: 0000000000180000
[ 83.560958] FS: 00007fd5032e8740(0000) GS:ffff9e66f1940000(0000) knlGS:0000000000000000
[ 83.562233] CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033
[ 83.563149] CR2: 00007fd5022b0da0 CR3: 000000038c334000 CR4: 00000000003406e0
Signed-off-by: Andrew Melnychenko <andrew@daynix.com>
Cc: stable <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20200414191503.3471783-1-andrew@daynix.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 3670664b5da555a2a481449b3baafff113b0ac35 upstream.
ev_byte_channel_send() assumes that its third argument is a 16 byte
array. Some places where it is called it may not be (or we can't
easily tell if it is). Newer compilers have started producing warnings
about this, so make sure we actually pass a 16 byte array.
There may be more elegant solutions to this, but the driver is quite
old and hasn't been updated in many years.
The warnings (from a powerpc allyesconfig build) are:
In file included from include/linux/byteorder/big_endian.h:5,
from arch/powerpc/include/uapi/asm/byteorder.h:14,
from include/asm-generic/bitops/le.h:6,
from arch/powerpc/include/asm/bitops.h:250,
from include/linux/bitops.h:29,
from include/linux/kernel.h:12,
from include/asm-generic/bug.h:19,
from arch/powerpc/include/asm/bug.h:109,
from include/linux/bug.h:5,
from include/linux/mmdebug.h:5,
from include/linux/gfp.h:5,
from include/linux/slab.h:15,
from drivers/tty/ehv_bytechan.c:24:
drivers/tty/ehv_bytechan.c: In function ‘ehv_bc_udbg_putc’:
arch/powerpc/include/asm/epapr_hcalls.h:298:20: warning: array subscript 1 is outside array bounds of ‘const char[1]’ [-Warray-bounds]
298 | r6 = be32_to_cpu(p[1]);
include/uapi/linux/byteorder/big_endian.h:40:51: note: in definition of macro ‘__be32_to_cpu’
40 | #define __be32_to_cpu(x) ((__force __u32)(__be32)(x))
| ^
arch/powerpc/include/asm/epapr_hcalls.h:298:7: note: in expansion of macro ‘be32_to_cpu’
298 | r6 = be32_to_cpu(p[1]);
| ^~~~~~~~~~~
drivers/tty/ehv_bytechan.c:166:13: note: while referencing ‘data’
166 | static void ehv_bc_udbg_putc(char c)
| ^~~~~~~~~~~~~~~~
Fixes: dcd83aaff1c8 ("tty/powerpc: introduce the ePAPR embedded hypervisor byte channel driver")
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Tested-by: Laurentiu Tudor <laurentiu.tudor@nxp.com>
[mpe: Trim warnings from change log]
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/20200109183912.5fcb52aa@canb.auug.org.au
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 7cf64b18b0b96e751178b8d0505d8466ff5a448f upstream.
vt_in_use() dereferences console_driver->ttys[i] without proper locking.
This is broken because the tty can be closed and freed concurrently.
We could fix this by using 'READ_ONCE(console_driver->ttys[i]) != NULL'
and skipping the check of tty_struct::count. But, looking at
console_driver->ttys[i] isn't really appropriate anyway because even if
it is NULL the tty can still be in the process of being closed.
Instead, fix it by making vt_in_use() require console_lock() and check
whether the vt is allocated and has port refcount > 1. This works since
following the patch "vt: vt_ioctl: fix VT_DISALLOCATE freeing in-use
virtual console" the port refcount is incremented while the vt is open.
Reproducer (very unreliable, but it worked for me after a few minutes):
#include <fcntl.h>
#include <linux/vt.h>
int main()
{
int fd, nproc;
struct vt_stat state;
char ttyname[16];
fd = open("/dev/tty10", O_RDONLY);
for (nproc = 1; nproc < 8; nproc *= 2)
fork();
for (;;) {
sprintf(ttyname, "/dev/tty%d", rand() % 8);
close(open(ttyname, O_RDONLY));
ioctl(fd, VT_GETSTATE, &state);
}
}
KASAN report:
BUG: KASAN: use-after-free in vt_in_use drivers/tty/vt/vt_ioctl.c:48 [inline]
BUG: KASAN: use-after-free in vt_ioctl+0x1ad3/0x1d70 drivers/tty/vt/vt_ioctl.c:657
Read of size 4 at addr ffff888065722468 by task syz-vt2/132
CPU: 0 PID: 132 Comm: syz-vt2 Not tainted 5.6.0-rc5-00130-g089b6d3654916 #13
Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS ?-20191223_100556-anatol 04/01/2014
Call Trace:
[...]
vt_in_use drivers/tty/vt/vt_ioctl.c:48 [inline]
vt_ioctl+0x1ad3/0x1d70 drivers/tty/vt/vt_ioctl.c:657
tty_ioctl+0x9db/0x11b0 drivers/tty/tty_io.c:2660
[...]
Allocated by task 136:
[...]
kzalloc include/linux/slab.h:669 [inline]
alloc_tty_struct+0x96/0x8a0 drivers/tty/tty_io.c:2982
tty_init_dev+0x23/0x350 drivers/tty/tty_io.c:1334
tty_open_by_driver drivers/tty/tty_io.c:1987 [inline]
tty_open+0x3ca/0xb30 drivers/tty/tty_io.c:2035
[...]
Freed by task 41:
[...]
kfree+0xbf/0x200 mm/slab.c:3757
free_tty_struct+0x8d/0xb0 drivers/tty/tty_io.c:177
release_one_tty+0x22d/0x2f0 drivers/tty/tty_io.c:1468
process_one_work+0x7f1/0x14b0 kernel/workqueue.c:2264
worker_thread+0x8b/0xc80 kernel/workqueue.c:2410
[...]
Fixes: 4001d7b7fc27 ("vt: push down the tty lock so we can see what is left to tackle")
Cc: <stable@vger.kernel.org> # v3.4+
Acked-by: Jiri Slaby <jslaby@suse.cz>
Signed-off-by: Eric Biggers <ebiggers@google.com>
Link: https://lore.kernel.org/r/20200322034305.210082-3-ebiggers@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit ca4463bf8438b403596edd0ec961ca0d4fbe0220 upstream.
The VT_DISALLOCATE ioctl can free a virtual console while tty_release()
is still running, causing a use-after-free in con_shutdown(). This
occurs because VT_DISALLOCATE considers a virtual console's
'struct vc_data' to be unused as soon as the corresponding tty's
refcount hits 0. But actually it may be still being closed.
Fix this by making vc_data be reference-counted via the embedded
'struct tty_port'. A newly allocated virtual console has refcount 1.
Opening it for the first time increments the refcount to 2. Closing it
for the last time decrements the refcount (in tty_operations::cleanup()
so that it happens late enough), as does VT_DISALLOCATE.
Reproducer:
#include <fcntl.h>
#include <linux/vt.h>
#include <sys/ioctl.h>
#include <unistd.h>
int main()
{
if (fork()) {
for (;;)
close(open("/dev/tty5", O_RDWR));
} else {
int fd = open("/dev/tty10", O_RDWR);
for (;;)
ioctl(fd, VT_DISALLOCATE, 5);
}
}
KASAN report:
BUG: KASAN: use-after-free in con_shutdown+0x76/0x80 drivers/tty/vt/vt.c:3278
Write of size 8 at addr ffff88806a4ec108 by task syz_vt/129
CPU: 0 PID: 129 Comm: syz_vt Not tainted 5.6.0-rc2 #11
Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS ?-20191223_100556-anatol 04/01/2014
Call Trace:
[...]
con_shutdown+0x76/0x80 drivers/tty/vt/vt.c:3278
release_tty+0xa8/0x410 drivers/tty/tty_io.c:1514
tty_release_struct+0x34/0x50 drivers/tty/tty_io.c:1629
tty_release+0x984/0xed0 drivers/tty/tty_io.c:1789
[...]
Allocated by task 129:
[...]
kzalloc include/linux/slab.h:669 [inline]
vc_allocate drivers/tty/vt/vt.c:1085 [inline]
vc_allocate+0x1ac/0x680 drivers/tty/vt/vt.c:1066
con_install+0x4d/0x3f0 drivers/tty/vt/vt.c:3229
tty_driver_install_tty drivers/tty/tty_io.c:1228 [inline]
tty_init_dev+0x94/0x350 drivers/tty/tty_io.c:1341
tty_open_by_driver drivers/tty/tty_io.c:1987 [inline]
tty_open+0x3ca/0xb30 drivers/tty/tty_io.c:2035
[...]
Freed by task 130:
[...]
kfree+0xbf/0x1e0 mm/slab.c:3757
vt_disallocate drivers/tty/vt/vt_ioctl.c:300 [inline]
vt_ioctl+0x16dc/0x1e30 drivers/tty/vt/vt_ioctl.c:818
tty_ioctl+0x9db/0x11b0 drivers/tty/tty_io.c:2660
[...]
Fixes: 4001d7b7fc27 ("vt: push down the tty lock so we can see what is left to tackle")
Cc: <stable@vger.kernel.org> # v3.4+
Reported-by: syzbot+522643ab5729b0421998@syzkaller.appspotmail.com
Acked-by: Jiri Slaby <jslaby@suse.cz>
Signed-off-by: Eric Biggers <ebiggers@google.com>
Link: https://lore.kernel.org/r/20200322034305.210082-2-ebiggers@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 1aa6e058dd6cd04471b1f21298270014daf48ac9 upstream.
The vc_cons_allocated() checks in vt_ioctl() and vt_compat_ioctl() are
unnecessary because they can only be reached by calling ioctl() on an
open tty, which implies the corresponding virtual console is allocated.
And even if the virtual console *could* be freed concurrently, then
these checks would be broken since they aren't done under console_lock,
and the vc_data is dereferenced before them anyway.
So, remove these unneeded checks to avoid confusion.
Signed-off-by: Eric Biggers <ebiggers@google.com>
Link: https://lore.kernel.org/r/20200224080326.295046-1-ebiggers@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit f400991bf872debffb01c46da882dc97d7e3248e upstream.
vt_dont_switch is pure boolean, no need for whole char.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Link: https://lore.kernel.org/r/20200219073951.16151-6-jslaby@suse.cz
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit e587e8f17433ddb26954f0edf5b2f95c42155ae9 upstream.
These two were macros. Switch them to static inlines, so that it's more
understandable what they are doing.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Link: https://lore.kernel.org/r/20200219073951.16151-2-jslaby@suse.cz
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit dce05aa6eec977f1472abed95ccd71276b9a3864 upstream.
Avoid global variables (namely sel_cons) by introducing vc_is_sel. It
checks whether the parameter is the current selection console. This will
help putting sel_cons to a struct later.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Link: https://lore.kernel.org/r/20200219073951.16151-1-jslaby@suse.cz
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit e8c75a30a23c6ba63f4ef6895cbf41fd42f21aa2 upstream.
sel_lock cannot nest in the console lock. Thanks to syzkaller, the
kernel states firmly:
> WARNING: possible circular locking dependency detected
> 5.6.0-rc3-syzkaller #0 Not tainted
> ------------------------------------------------------
> syz-executor.4/20336 is trying to acquire lock:
> ffff8880a2e952a0 (&tty->termios_rwsem){++++}, at: tty_unthrottle+0x22/0x100 drivers/tty/tty_ioctl.c:136
>
> but task is already holding lock:
> ffffffff89462e70 (sel_lock){+.+.}, at: paste_selection+0x118/0x470 drivers/tty/vt/selection.c:374
>
> which lock already depends on the new lock.
>
> the existing dependency chain (in reverse order) is:
>
> -> #2 (sel_lock){+.+.}:
> mutex_lock_nested+0x1b/0x30 kernel/locking/mutex.c:1118
> set_selection_kernel+0x3b8/0x18a0 drivers/tty/vt/selection.c:217
> set_selection_user+0x63/0x80 drivers/tty/vt/selection.c:181
> tioclinux+0x103/0x530 drivers/tty/vt/vt.c:3050
> vt_ioctl+0x3f1/0x3a30 drivers/tty/vt/vt_ioctl.c:364
This is ioctl(TIOCL_SETSEL).
Locks held on the path: console_lock -> sel_lock
> -> #1 (console_lock){+.+.}:
> console_lock+0x46/0x70 kernel/printk/printk.c:2289
> con_flush_chars+0x50/0x650 drivers/tty/vt/vt.c:3223
> n_tty_write+0xeae/0x1200 drivers/tty/n_tty.c:2350
> do_tty_write drivers/tty/tty_io.c:962 [inline]
> tty_write+0x5a1/0x950 drivers/tty/tty_io.c:1046
This is write().
Locks held on the path: termios_rwsem -> console_lock
> -> #0 (&tty->termios_rwsem){++++}:
> down_write+0x57/0x140 kernel/locking/rwsem.c:1534
> tty_unthrottle+0x22/0x100 drivers/tty/tty_ioctl.c:136
> mkiss_receive_buf+0x12aa/0x1340 drivers/net/hamradio/mkiss.c:902
> tty_ldisc_receive_buf+0x12f/0x170 drivers/tty/tty_buffer.c:465
> paste_selection+0x346/0x470 drivers/tty/vt/selection.c:389
> tioclinux+0x121/0x530 drivers/tty/vt/vt.c:3055
> vt_ioctl+0x3f1/0x3a30 drivers/tty/vt/vt_ioctl.c:364
This is ioctl(TIOCL_PASTESEL).
Locks held on the path: sel_lock -> termios_rwsem
> other info that might help us debug this:
>
> Chain exists of:
> &tty->termios_rwsem --> console_lock --> sel_lock
Clearly. From the above, we have:
console_lock -> sel_lock
sel_lock -> termios_rwsem
termios_rwsem -> console_lock
Fix this by reversing the console_lock -> sel_lock dependency in
ioctl(TIOCL_SETSEL). First, lock sel_lock, then console_lock.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Reported-by: syzbot+26183d9746e62da329b8@syzkaller.appspotmail.com
Fixes: 07e6124a1a46 ("vt: selection, close sel_buffer race")
Cc: stable <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20200228115406.5735-2-jslaby@suse.cz
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 4b70dd57a15d2f4685ac6e38056bad93e81e982f upstream.
We need to nest the console lock in sel_lock, so we have to push it down
a bit. Fortunately, the callers of set_selection_* just lock the console
lock around the function call. So moving it down is easy.
In the next patch, we switch the order.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Fixes: 07e6124a1a46 ("vt: selection, close sel_buffer race")
Cc: stable <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20200228115406.5735-1-jslaby@suse.cz
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 07e6124a1a46b4b5a9b3cacc0c306b50da87abf5 upstream.
syzkaller reported this UAF:
BUG: KASAN: use-after-free in n_tty_receive_buf_common+0x2481/0x2940 drivers/tty/n_tty.c:1741
Read of size 1 at addr ffff8880089e40e9 by task syz-executor.1/13184
CPU: 0 PID: 13184 Comm: syz-executor.1 Not tainted 5.4.7 #1
Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS 1.12.0-1 04/01/2014
Call Trace:
...
kasan_report+0xe/0x20 mm/kasan/common.c:634
n_tty_receive_buf_common+0x2481/0x2940 drivers/tty/n_tty.c:1741
tty_ldisc_receive_buf+0xac/0x190 drivers/tty/tty_buffer.c:461
paste_selection+0x297/0x400 drivers/tty/vt/selection.c:372
tioclinux+0x20d/0x4e0 drivers/tty/vt/vt.c:3044
vt_ioctl+0x1bcf/0x28d0 drivers/tty/vt/vt_ioctl.c:364
tty_ioctl+0x525/0x15a0 drivers/tty/tty_io.c:2657
vfs_ioctl fs/ioctl.c:47 [inline]
It is due to a race between parallel paste_selection (TIOCL_PASTESEL)
and set_selection_user (TIOCL_SETSEL) invocations. One uses sel_buffer,
while the other frees it and reallocates a new one for another
selection. Add a mutex to close this race.
The mutex takes care properly of sel_buffer and sel_buffer_lth only. The
other selection global variables (like sel_start, sel_end, and sel_cons)
are protected only in set_selection_user. The other functions need quite
some more work to close the races of the variables there. This is going
to happen later.
This likely fixes (I am unsure as there is no reproducer provided) bug
206361 too. It was marked as CVE-2020-8648.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Reported-by: syzbot+59997e8d5cbdc486e6f6@syzkaller.appspotmail.com
References: https://bugzilla.kernel.org/show_bug.cgi?id=206361
Cc: stable <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20200210081131.23572-2-jslaby@suse.cz
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit 87c5cbf71ecbb9e289d60a2df22eb686c70bf196 ]
On AR934x this UART is usually not initialized by the bootloader
as it is only used as a secondary serial port while the primary
UART is a newly introduced NS16550-compatible.
In order to make use of the ar933x-uart on AR934x without RTS/CTS
hardware flow control, one needs to set the
UART_CS_{RX,TX}_READY_ORIDE bits as other than on AR933x where this
UART is used as primary/console, the bootloader on AR934x typically
doesn't set those bits.
Setting them explicitely on AR933x should not do any harm, so just
set them unconditionally.
Tested-by: Chuanhong Guo <gch981213@gmail.com>
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Link: https://lore.kernel.org/r/20200207095335.GA179836@makrotopia.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
commit c3fee60908db4a8594f2e4a2131998384b8fa006 upstream.
The commit 97f5f0cd8cd0a0544 ("Input: implement SysRq as a separate input
handler") added pr_fmt() definition. It caused a duplicated message
prefix in the sysrq header messages, for example:
[ 177.053931] sysrq: SysRq : Show backtrace of all active CPUs
[ 742.864776] sysrq: SysRq : HELP : loglevel(0-9) reboot(b) crash(c)
Fixes: 97f5f0cd8cd0a05 ("Input: implement SysRq as a separate input handler")
Signed-off-by: Petr Mladek <pmladek@suse.com>
Reviewed-by: Sergey Senozhatsky <sergey.senozhatsky@gmail.com>
Cc: Tommi Rantala <tommi.t.rantala@nokia.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 075e1a0c50f59ea210561d0d0fedbd945615df78 upstream.
The sysrq header line is printed with an increased loglevel
to provide users some positive feedback.
The original loglevel is not restored when the sysrq operation
is disabled. This bug was introduced in 2.6.12 (pre-git-history)
by the commit ("Allow admin to enable only some of the Magic-Sysrq
functions").
Signed-off-by: Petr Mladek <pmladek@suse.com>
Reviewed-by: Sergey Senozhatsky <sergey.senozhatsky@gmail.com>
Reviewed-by: Steven Rostedt (VMware) <rostedt@goodmis.org>
Cc: Tommi Rantala <tommi.t.rantala@nokia.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
