summaryrefslogtreecommitdiff
path: root/drivers/tty/serial
AgeCommit message (Collapse)Author
2020-09-21Merge 5.9.0-rc6 into tty-nextGreg Kroah-Hartman
We need the tty/serial fixes in here and this resolves a merge issue in the 8250 driver. Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2020-09-16tty: serial: qcom_geni_serial: Fix the UART wakeup issuesatya priya
As a part of system suspend uart_port_suspend is called from the Serial driver, which calls set_mctrl passing mctrl as 0. This makes RFR high(NOT_READY) during suspend. Due to this BT SoC is not able to send wakeup bytes to UART during suspend. Include if check for non-suspend case to keep RFR low during suspend. Signed-off-by: satya priya <skakit@codeaurora.org> Reviewed-by: Akash Asthana <akashast@codeaurora.org> Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org> Link: https://lore.kernel.org/r/1599742438-16811-5-git-send-email-skakit@codeaurora.org Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2020-09-16serial: 8250_pci: Add Realtek 816a and 816bTobias Diedrich
These serial ports are exposed by the OOB-management-engine on RealManage-enabled network cards (e.g. AMD DASH enabled systems using Realtek cards). Because these have 3 BARs, they fail the "num_iomem <= 1" check in serial_pci_guess_board. I've manually checked the two IOMEM regions and BAR 2 doesn't seem to respond to reads, but BAR 4 seems to be an MMIO version of the IO ports (untested). With this change, the ports are detected: 0000:02:00.1: ttyS0 at I/O 0x2200 (irq = 82, base_baud = 115200) is a 16550A 0000:02:00.2: ttyS1 at I/O 0x2100 (irq = 55, base_baud = 115200) is a 16550A lspci output: 02:00.1 0700: 10ec:816a (rev 0e) (prog-if 02 [16550]) Subsystem: 17aa:5082 Control: I/O+ Mem+ BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort+ <TAbort- <MAbort- >SERR- <PERR- INTx- Interrupt: pin B routed to IRQ 82 IOMMU group: 11 Region 0: I/O ports at 2200 [size=256] Region 2: Memory at fd715000 (64-bit, non-prefetchable) [size=4K] Region 4: Memory at fd704000 (64-bit, non-prefetchable) [size=16K] Capabilities: [40] Power Management version 3 Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=375mA PME(D0+,D1+,D2+,D3hot+,D3cold+) Status: D0 NoSoftRst+ PME-Enable- DSel=0 DScale=0 PME- Capabilities: [50] MSI: Enable- Count=1/1 Maskable- 64bit+ Address: 0000000000000000 Data: 0000 Capabilities: [70] Express (v2) Endpoint, MSI 01 DevCap: MaxPayload 128 bytes, PhantFunc 0, Latency L0s unlimited, L1 <64us ExtTag- AttnBtn- AttnInd- PwrInd- RBE+ FLReset- SlotPowerLimit 0.000W DevCtl: CorrErr- NonFatalErr- FatalErr- UnsupReq- RlxdOrd+ ExtTag- PhantFunc- AuxPwr- NoSnoop- MaxPayload 128 bytes, MaxReadReq 512 bytes DevSta: CorrErr+ NonFatalErr- FatalErr- UnsupReq+ AuxPwr+ TransPend- LnkCap: Port #0, Speed 2.5GT/s, Width x1, ASPM L0s L1, Exit Latency L0s unlimited, L1 <64us ClockPM+ Surprise- LLActRep- BwNot- ASPMOptComp+ LnkCtl: ASPM L1 Enabled; RCB 64 bytes, Disabled- CommClk+ ExtSynch- ClockPM- AutWidDis- BWInt- AutBWInt- LnkSta: Speed 2.5GT/s (ok), Width x1 (ok) TrErr- Train- SlotClk+ DLActive- BWMgmt- ABWMgmt- DevCap2: Completion Timeout: Range ABCD, TimeoutDis+ NROPrPrP- LTR+ 10BitTagComp- 10BitTagReq- OBFF Via message/WAKE#, ExtFmt- EETLPPrefix- EmergencyPowerReduction Not Supported, EmergencyPowerReductionInit- FRS- TPHComp- ExtTPHComp- AtomicOpsCap: 32bit- 64bit- 128bitCAS- DevCtl2: Completion Timeout: 50us to 50ms, TimeoutDis- LTR- OBFF Disabled, AtomicOpsCtl: ReqEn- LnkSta2: Current De-emphasis Level: -6dB, EqualizationComplete- EqualizationPhase1- EqualizationPhase2- EqualizationPhase3- LinkEqualizationRequest- Retimer- 2Retimers- CrosslinkRes: unsupported Capabilities: [b0] MSI-X: Enable- Count=4 Masked- Vector table: BAR=4 offset=00000000 PBA: BAR=4 offset=00000800 Capabilities: [d0] Vital Product Data Not readable Capabilities: [100 v2] Advanced Error Reporting UESta: DLP- SDES- TLP- FCP- CmpltTO- CmpltAbrt- UnxCmplt- RxOF- MalfTLP- ECRC- UnsupReq- ACSViol- UEMsk: DLP- SDES- TLP- FCP- CmpltTO- CmpltAbrt- UnxCmplt- RxOF- MalfTLP- ECRC- UnsupReq- ACSViol- UESvrt: DLP+ SDES+ TLP- FCP+ CmpltTO- CmpltAbrt- UnxCmplt- RxOF+ MalfTLP+ ECRC- UnsupReq- ACSViol- CESta: RxErr- BadTLP- BadDLLP- Rollover- Timeout- AdvNonFatalErr+ CEMsk: RxErr- BadTLP- BadDLLP- Rollover- Timeout- AdvNonFatalErr+ AERCap: First Error Pointer: 00, ECRCGenCap+ ECRCGenEn- ECRCChkCap+ ECRCChkEn- MultHdrRecCap- MultHdrRecEn- TLPPfxPres- HdrLogCap- HeaderLog: 00000000 00000000 00000000 00000000 Capabilities: [160 v1] Device Serial Number 00-00-00-00-00-00-00-00 Capabilities: [170 v1] Latency Tolerance Reporting Max snoop latency: 0ns Max no snoop latency: 0ns Capabilities: [178 v1] L1 PM Substates L1SubCap: PCI-PM_L1.2+ PCI-PM_L1.1+ ASPM_L1.2+ ASPM_L1.1+ L1_PM_Substates+ PortCommonModeRestoreTime=150us PortTPowerOnTime=150us L1SubCtl1: PCI-PM_L1.2- PCI-PM_L1.1- ASPM_L1.2- ASPM_L1.1- T_CommonMode=0us LTR1.2_Threshold=0ns L1SubCtl2: T_PwrOn=10us 02:00.2 0700: 10ec:816b (rev 0e) [...same...] Signed-off-by: Tobias Diedrich <tobiasdiedrich@gmail.com> Cc: stable <stable@vger.kernel.org> Link: https://lore.kernel.org/r/20200914173628.GA22508@yamamaya.is-a-geek.org Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2020-09-16serial: core: fix console port-lock regressionJohan Hovold
Fix the port-lock initialisation regression introduced by commit a3cb39d258ef ("serial: core: Allow detach and attach serial device for console") by making sure that the lock is again initialised during console setup. The console may be registered before the serial controller has been probed in which case the port lock needs to be initialised during console setup by a call to uart_set_options(). The console-detach changes introduced a regression in several drivers by effectively removing that initialisation by not initialising the lock when the port is used as a console (which is always the case during console setup). Add back the early lock initialisation and instead use a new console-reinit flag to handle the case where a console is being re-attached through sysfs. The question whether the console-detach interface should have been added in the first place is left for another discussion. Note that the console-enabled check in uart_set_options() is not redundant because of kgdboc, which can end up reinitialising an already enabled console (see commit 42b6a1baa3ec ("serial_core: Don't re-initialize a previously initialized spinlock.")). Fixes: a3cb39d258ef ("serial: core: Allow detach and attach serial device for console") Cc: stable <stable@vger.kernel.org> # 5.7 Signed-off-by: Johan Hovold <johan@kernel.org> Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com> Link: https://lore.kernel.org/r/20200909143101.15389-3-johan@kernel.org Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2020-09-16serial: core: fix port-lock initialisationJohan Hovold
Commit f743061a85f5 ("serial: core: Initialise spin lock before use in uart_configure_port()") tried to work around a breakage introduced by commit a3cb39d258ef ("serial: core: Allow detach and attach serial device for console") by adding a second initialisation of the port lock when registering the port. As reported by the build robots [1], this doesn't really solve the regression introduced by the console-detach changes and also adds a second redundant initialisation of the lock for normal ports. Start cleaning up this mess by removing the redundant initialisation and making sure that the port lock is again initialised once-only for ports that aren't already in use as a console. [1] https://lore.kernel.org/r/20200802054852.GR23458@shao2-debian Fixes: f743061a85f5 ("serial: core: Initialise spin lock before use in uart_configure_port()") Fixes: a3cb39d258ef ("serial: core: Allow detach and attach serial device for console") Cc: stable <stable@vger.kernel.org> # 5.7 Signed-off-by: Johan Hovold <johan@kernel.org> Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com> Link: https://lore.kernel.org/r/20200909143101.15389-2-johan@kernel.org Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2020-09-16tty: serial: qcom_geni_serial: 115.2 is a better console default than 9600Douglas Anderson
Commit c5cbc78acf69 ("tty: serial: qcom_geni_serial: Initialize baud in qcom_geni_console_setup") fixed a bug by initting a variable that was used in some cases without initialization. However, the "default" baud rate picked by that CL was probably not the best choice. The chances that anyone out there is trying to run a system with kernel messages piped out over a 9600 baud serial port is just about nil. Console messages are printed in a blocking manner. At 9600 baud we print about 1 character per millisecond which means that printing a 40-byte message to the console will take ~40 ms. While it would probably work, it's going to make boot _very_ slow and probably cause the occasional timeout here and there in drivers (heck, even at 115200 console delays can wreck havoc). This has already bit at least two people that I'm aware of that tried to enable serial console by just adding "console=ttyMSM0" (instead of "console=ttyMSM0,115200n8") to the command line, so it seems like it'd be nice to fix. Let's switch the default to 115200. Reviewed-by: Nathan Chancellor <natechancellor@gmail.com> Reviewed-by: Akash Asthana <akashast@codeaurora.org> Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org> Signed-off-by: Douglas Anderson <dianders@chromium.org> Link: https://lore.kernel.org/r/20200911080054.1.I4c00b921c2f17b6988688046fa7be0f729f8d591@changeid Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2020-09-16serial: pmac_zilog: use for_each_child_of_node() macroQinglang Miao
Use for_each_child_of_node() macro instead of open coding it. Signed-off-by: Qinglang Miao <miaoqinglang@huawei.com> Link: https://lore.kernel.org/r/20200916062138.191188-1-miaoqinglang@huawei.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2020-09-16tty: serial: 8250_mtk: set regshift for mmio32Hsin-Yi Wang
To use mmio32, we also need to set regshift. Signed-off-by: Hsin-Yi Wang <hsinyi@chromium.org> Acked-by: Eddie Huang <eddie.huang@mediatek.com> Link: https://lore.kernel.org/r/20200915054825.3289105-2-hsinyi@chromium.org Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2020-09-16tty: serial: print earlycon info after match->setupHsin-Yi Wang
8250 devices may modify iotype in their own earlycon setup. For example: 8250_mtk and 8250_uniphier force iotype to be MMIO32. Print earlycon info after match->setup to reflect actual earlycon info. Signed-off-by: Hsin-Yi Wang <hsinyi@chromium.org> Link: https://lore.kernel.org/r/20200915054825.3289105-1-hsinyi@chromium.org Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2020-09-16serial: ucc_uart: make qe_uart_set_mctrl() staticJason Yan
This eliminates the following sparse warning: drivers/tty/serial/ucc_uart.c:286:6: warning: symbol 'qe_uart_set_mctrl' was not declared. Should it be static? Reported-by: Hulk Robot <hulkci@huawei.com> Acked-by: Jiri Slaby <jirislaby@kernel.org> Signed-off-by: Jason Yan <yanaijie@huawei.com> Link: https://lore.kernel.org/r/20200912033834.143166-1-yanaijie@huawei.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2020-09-16serial: 8250_pci: Remove unused function get_pci_irq()YueHaibing
It is not used since commit 8428413b1d14 ("serial: 8250_pci: Implement MSI(-X) support") Signed-off-by: YueHaibing <yuehaibing@huawei.com> Link: https://lore.kernel.org/r/20200909135103.17768-1-yuehaibing@huawei.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2020-09-13Merge tag 'samsung-soc-s3c-5.10' of ↵Olof Johansson
https://git.kernel.org/pub/scm/linux/kernel/git/krzk/linux into arm/soc Samsung S3C24xx and S3C64xx machine code cleanup for v5.10 Big cleanup for the Samsung S3C24xx and S3C64xx platforms, although it also touches files shared with S5Pv210 and Exynos. This is mostly Arnd Bergmann work which Krzysztof Kozlowski took over, rebased and polished. The goal is to cleanup, merge and finally make the Samsung S3C24xx and S3C64xx architectures multiplatform. The multiplatform did not happen yet here - just cleaning up and merging into one arch/arm/mach-s3c directory. However this is step forward for multiplatform or at least to keep this code still maintainable. This pulls also branch with changes for Samsung SoC sound drivers from broonie/sound because the cleanups there were part of this series and all further patches depend on them. * tag 'samsung-soc-s3c-5.10' of https://git.kernel.org/pub/scm/linux/kernel/git/krzk/linux: (62 commits) ARM: s3c: Avoid naming clash of S3C24xx and S3C64xx timer setup ARM: s3c: Cleanup from old plat-samsung include ARM: s3c: make headers local if possible ARM: s3c: move into a common directory ARM: s3c24xx: stop including mach/hardware.h from mach/io.h cpufreq: s3c24xx: move low-level clk reg access into platform code cpufreq: s3c2412: use global s3c2412_cpufreq_setrefresh ARM: s3c: remove cpufreq header dependencies cpufreq: s3c24xx: split out registers fbdev: s3c2410fb: remove mach header dependency ARM: s3c24xx: bast: avoid irq_desc array usage ARM: s3c24xx: spi: avoid hardcoding fiq number in driver ARM: s3c24xx: include mach/irqs.h where needed ARM: s3c24xx: move s3cmci pinctrl handling into board files ARM: s3c24xx: move iis pinctrl config into boards ARM: s3c24xx: move spi fiq handler into platform ARM: s3c: adc: move header to linux/soc/samsung ARM: s3c24xx: move irqchip driver back into platform ARM: s3c24xx: move regs-spi.h into spi driver ARM: s3c64xx: remove mach/hardware.h ... Link: https://lore.kernel.org/r/20200831154751.7551-1-krzk@kernel.org Signed-off-by: Olof Johansson <olof@lixom.net>
2020-09-07MIPS: Replace SIBYTE_1956_WAR by CONFIG_SB1_PASS_2_WORKAROUNDSThomas Bogendoerfer
SB1250 uart bug is related to PASS 2 workarounds. Use config CONFIG_SB1_PASS_2_WORKAROUNDS directly and get rid of SIBYTE_1956_WAR. Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
2020-09-04tty: serial: icom: switch from 'pci_' to 'dma_' APIChristophe JAILLET
The wrappers in include/linux/pci-dma-compat.h should go away. The patch has been generated with the coccinelle script below and has been hand modified to replace GFP_ with a correct flag. It has been compile tested. When memory is allocated in 'get_port_memory()', GFP_KERNEL can be used because it is only called from a probe function and no lock is acquired. The call chain is: icom_probe (the probe function) --> icom_load_ports --> get_port_memory When memory is allocated in 'load_code()', GFP_KERNEL can be used because it is only called from a .startup function. icom_open (the .startup function of struct uart_ops) --> startup --> load_code .startup functions are protected using a semaphore and no spinlock is taken. @@ @@ - PCI_DMA_BIDIRECTIONAL + DMA_BIDIRECTIONAL @@ @@ - PCI_DMA_TODEVICE + DMA_TO_DEVICE @@ @@ - PCI_DMA_FROMDEVICE + DMA_FROM_DEVICE @@ @@ - PCI_DMA_NONE + DMA_NONE @@ expression e1, e2, e3; @@ - pci_alloc_consistent(e1, e2, e3) + dma_alloc_coherent(&e1->dev, e2, e3, GFP_) @@ expression e1, e2, e3; @@ - pci_zalloc_consistent(e1, e2, e3) + dma_alloc_coherent(&e1->dev, e2, e3, GFP_) @@ expression e1, e2, e3, e4; @@ - pci_free_consistent(e1, e2, e3, e4) + dma_free_coherent(&e1->dev, e2, e3, e4) @@ expression e1, e2, e3, e4; @@ - pci_map_single(e1, e2, e3, e4) + dma_map_single(&e1->dev, e2, e3, e4) @@ expression e1, e2, e3, e4; @@ - pci_unmap_single(e1, e2, e3, e4) + dma_unmap_single(&e1->dev, e2, e3, e4) @@ expression e1, e2, e3, e4, e5; @@ - pci_map_page(e1, e2, e3, e4, e5) + dma_map_page(&e1->dev, e2, e3, e4, e5) @@ expression e1, e2, e3, e4; @@ - pci_unmap_page(e1, e2, e3, e4) + dma_unmap_page(&e1->dev, e2, e3, e4) @@ expression e1, e2, e3, e4; @@ - pci_map_sg(e1, e2, e3, e4) + dma_map_sg(&e1->dev, e2, e3, e4) @@ expression e1, e2, e3, e4; @@ - pci_unmap_sg(e1, e2, e3, e4) + dma_unmap_sg(&e1->dev, e2, e3, e4) @@ expression e1, e2, e3, e4; @@ - pci_dma_sync_single_for_cpu(e1, e2, e3, e4) + dma_sync_single_for_cpu(&e1->dev, e2, e3, e4) @@ expression e1, e2, e3, e4; @@ - pci_dma_sync_single_for_device(e1, e2, e3, e4) + dma_sync_single_for_device(&e1->dev, e2, e3, e4) @@ expression e1, e2, e3, e4; @@ - pci_dma_sync_sg_for_cpu(e1, e2, e3, e4) + dma_sync_sg_for_cpu(&e1->dev, e2, e3, e4) @@ expression e1, e2, e3, e4; @@ - pci_dma_sync_sg_for_device(e1, e2, e3, e4) + dma_sync_sg_for_device(&e1->dev, e2, e3, e4) @@ expression e1, e2; @@ - pci_dma_mapping_error(e1, e2) + dma_mapping_error(&e1->dev, e2) @@ expression e1, e2; @@ - pci_set_dma_mask(e1, e2) + dma_set_mask(&e1->dev, e2) @@ expression e1, e2; @@ - pci_set_consistent_dma_mask(e1, e2) + dma_set_coherent_mask(&e1->dev, e2) Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr> Link: https://lore.kernel.org/r/20200806060507.730142-1-christophe.jaillet@wanadoo.fr Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2020-09-04serial: 8250_fsl: Add ACPI supportkuldip dwivedi
This adds support for ACPI enumerated FSL 16550 UARTs. For supporting ACPI, I added a wrapper so that this driver can be used if firmware has exposed the HID "NXP0018" in DSDT table. This will be built as object file if config "SERIAL_8250_FSL" is enabled which depends on config "SERIAL_8250_CONSOLE". Signed-off-by: kuldip dwivedi <kuldip.dwivedi@puresoftware.com> Link: https://lore.kernel.org/r/20200903113402.12371-1-kuldip.dwivedi@puresoftware.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2020-09-04serial: stm32: Add RS485 RTS GPIO control againMarek Vasut
While the STM32 does support RS485 drive-enable control within the UART IP itself, some systems have the drive-enable line connected to a pin which cannot be pinmuxed as RTS. Add support for toggling the RTS GPIO line using the modem control GPIOs to provide at least some sort of emulation. Fixes: 7df5081cbf5e ("serial: stm32: Add RS485 RTS GPIO control") Signed-off-by: Marek Vasut <marex@denx.de> Cc: Alexandre Torgue <alexandre.torgue@st.com> Cc: Andy Shevchenko <andy.shevchenko@gmail.com> Cc: Manivannan Sadhasivam <mani@kernel.org> Cc: Fabrice Gasnier <fabrice.gasnier@st.com> Cc: linux-stm32@st-md-mailman.stormreply.com Link: https://lore.kernel.org/r/20200831171045.205691-1-marex@denx.de Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2020-09-04tty: serial: earlycon dependencyTong Zhang
parse_options() in drivers/tty/serial/earlycon.c calls uart_parse_earlycon in drivers/tty/serial/serial_core.c therefore selecting SERIAL_EARLYCON should automatically select SERIAL_CORE, otherwise will result in symbol not found error during linking if SERIAL_CORE is not configured as builtin Fixes: 9aac5887595b ("tty/serial: add generic serial earlycon") Signed-off-by: Tong Zhang <ztong0001@gmail.com> Link: https://lore.kernel.org/r/20200828123949.2642-1-ztong0001@gmail.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2020-09-04sc16is7xx: Set iobase to device indexDaniel Mack
Some derivates of sc16is7xx devices expose more than one tty device to userspace. If multiple such devices exist in a system, userspace currently has no clean way to infer which tty maps to which physical line. Set the .iobase value to the relative index within the device to allow infering the order through sysfs. Signed-off-by: Daniel Mack <daniel@zonque.org> Link: https://lore.kernel.org/r/20200901120329.4176302-1-daniel@zonque.org Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2020-09-04serial: core: Simplify with dev_err_probe()Krzysztof Kozlowski
Common pattern of handling deferred probe can be simplified with dev_err_probe(). Less code and the error value gets printed. Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org> Reviewed-by: Lukas Wunner <lukas@wunner.de> Link: https://lore.kernel.org/r/20200901153100.18827-2-krzk@kernel.org Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2020-09-04serial: 8250: Simplify with dev_err_probe()Krzysztof Kozlowski
Common pattern of handling deferred probe can be simplified with dev_err_probe(). Less code and the error value gets printed. Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org> Acked-by: Florian Fainelli <f.fainelli@gmail.com> Reviewed-by: Lukas Wunner <lukas@wunner.de> Link: https://lore.kernel.org/r/20200901153100.18827-1-krzk@kernel.org Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2020-09-04serial: imx: Delete duplicated argument to '|' in imx_uart_probeYe Bin
When calculate "ucr1" UCR1_TRDYEN is duplicate. Signed-off-by: Ye Bin <yebin10@huawei.com> Reviewed-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de> Link: https://lore.kernel.org/r/20200903062401.692442-1-yebin10@huawei.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2020-08-31Merge 5.9-rc3 into tty-nextGreg Kroah-Hartman
We need the tty/serial fixes in here as well. Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2020-08-28serial: 8250_pci: Add WCH384_8S 8 port serial deviceDu Huanpeng
Add PCI id for WCH384_8S 8 port PCI-E serial card. because this card has so many ports, you may have to check these two options before use it: CONFIG_SERIAL_8250_RUNTIME_UARTS CONFIG_SERIAL_8250_NR_UARTS Signed-off-by: Du Huanpeng <u74147@gmail.com> Link: https://lore.kernel.org/r/1598060848-27807-1-git-send-email-u74147@gmail.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2020-08-28tty: serial: qcom_geni_serial: Unconditionally call dev_pm_opp_of_remove_table()Viresh Kumar
dev_pm_opp_of_remove_table() doesn't report any errors when it fails to find the OPP table with error -ENODEV (i.e. OPP table not present for the device). And we can call dev_pm_opp_of_remove_table() unconditionally here. While at it, create a new label to put clkname on errors. Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org> Link: https://lore.kernel.org/r/583003f385a103b4c089ce8144a215c58cfb117a.1598594714.git.viresh.kumar@linaro.org Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2020-08-28serial: core: don't use snprintf() for formatting sysfs attrsAlex Dewar
As per the documentation (Documentation/filesystems/sysfs.rst), snprintf() should not be used for formatting values returned by sysfs. For all of the instances in serial_core.c, we know that the string will be <PAGE_SIZE in length, so just use sprintf(). Issue identified by Coccinelle. Signed-off-by: Alex Dewar <alex.dewar90@gmail.com> Link: https://lore.kernel.org/r/20200824223932.27709-1-alex.dewar90@gmail.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2020-08-28serial: fsl_lpuart: Fix typo in "transfer"Fabio Estevam
Fix two occurrences where "transfer" is spelled incorrectly. Signed-off-by: Fabio Estevam <festevam@gmail.com> Link: https://lore.kernel.org/r/20200818224457.16507-1-festevam@gmail.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2020-08-26Merge tag 'tty-5.9-rc3' of ↵Linus Torvalds
git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty Pull tty/serial fixes from Greg KH: "Here are a few small TTY/Serial/vt fixes for 5.9-rc3 Included in here are: - qcom serial fixes - vt ioctl and core bugfixes - pl011 serial driver fixes - 8250 serial driver fixes - other misc serial driver fixes and for good measure: - fbcon fix for syzbot found problem. All of these have been in linux-next for a while with no reported issues" * tag 'tty-5.9-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty: tty: serial: imx: add dependence and build for earlycon serial: samsung: Removes the IRQ not found warning serial: 8250: change lock order in serial8250_do_startup() serial: stm32: avoid kernel warning on absence of optional IRQ serial: pl011: Fix oops on -EPROBE_DEFER serial: pl011: Don't leak amba_ports entry on driver register error serial: 8250_exar: Fix number of ports for Commtech PCIe cards tty: serial: qcom_geni_serial: Drop __init from qcom_geni_console_setup serial: qcom_geni_serial: Fix recent kdb hang vt_ioctl: change VT_RESIZEX ioctl to check for error return from vc_resize() fbcon: prevent user font height or width change from causing potential out-of-bounds access vt: defer kfree() of vc_screenbuf in vc_do_resize()
2020-08-23treewide: Use fallthrough pseudo-keywordGustavo A. R. Silva
Replace the existing /* fall through */ comments and its variants with the new pseudo-keyword macro fallthrough[1]. Also, remove unnecessary fall-through markings when it is the case. [1] https://www.kernel.org/doc/html/v5.7/process/deprecated.html?highlight=fallthrough#implicit-switch-case-fall-through Signed-off-by: Gustavo A. R. Silva <gustavoars@kernel.org>
2020-08-19ARM: s5pv210: don't imply CONFIG_PLAT_SAMSUNGArnd Bergmann
The plat-samsung directory and mach-s5pv210 can be build completely independently, so split the two Kconfig symbols CONFIG_PLAT_SAMSUNG and CONFIG_ARCH_S5PV210. Signed-off-by: Arnd Bergmann <arnd@arndb.de> Acked-by: Ulf Hansson <ulf.hansson@linaro.org> Acked-by: Thierry Reding <thierry.reding@gmail.com> Acked-by: Mark Brown <broonie@kernel.org> Link: https://lore.kernel.org/r/20200806182059.2431-18-krzk@kernel.org Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
2020-08-18serial: sa1100: use platform_get_resource()Andy Shevchenko
Use platform_get_resource() to fetch the memory resource instead of open-coded variant. While here, fail the probe if no resource found or no port is added. Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com> Link: https://lore.kernel.org/r/20200804134807.11589-1-andriy.shevchenko@linux.intel.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2020-08-18tty: serial: imx: add dependence and build for earlyconFugang Duan
Add the earlycon dependence and add earlycon Makefile support to allow to build the driver. Fixes: 699cc4dfd140 ("tty: serial: imx: add imx earlycon driver") Signed-off-by: Fugang Duan <fugang.duan@nxp.com> Link: https://lore.kernel.org/r/20200810060652.3436-1-fugang.duan@nxp.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2020-08-18serial: samsung: Removes the IRQ not found warningTamseel Shams
In few older Samsung SoCs like s3c2410, s3c2412 and s3c2440, UART IP is having 2 interrupt lines. However, in other SoCs like s3c6400, s5pv210, exynos5433, and exynos4210 UART is having only 1 interrupt line. Due to this, "platform_get_irq(platdev, 1)" call in the driver gives the following false-positive error: "IRQ index 1 not found" on newer SoC's. This patch adds the condition to check for Tx interrupt only for the those SoC's which have 2 interrupt lines. Tested-by: Alim Akhtar <alim.akhtar@samsung.com> Tested-by: Marek Szyprowski <m.szyprowski@samsung.com> Reviewed-by: Krzysztof Kozlowski <krzk@kernel.org> Reviewed-by: Alim Akhtar <alim.akhtar@samsung.com> Signed-off-by: Tamseel Shams <m.shams@samsung.com> Cc: stable <stable@vger.kernel.org> Link: https://lore.kernel.org/r/20200810030021.45348-1-m.shams@samsung.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2020-08-18tty: serial, fix kernel-docJiri Slaby
As in the previous patches, fix kernel-doc in serial drivers. Signed-off-by: Jiri Slaby <jslaby@suse.cz> Link: https://lore.kernel.org/r/20200818085655.12071-8-jslaby@suse.cz Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2020-08-18tty: timbuart: convert tasklets to use new tasklet_setup() APIAllen Pais
In preparation for unconditionally passing the struct tasklet_struct pointer to all tasklet callbacks, switch to using the new tasklet_setup() and from_tasklet() to pass the tasklet pointer explicitly. Signed-off-by: Romain Perier <romain.perier@gmail.com> Signed-off-by: Allen Pais <allen.lkml@gmail.com> Link: https://lore.kernel.org/r/20200817085921.26033-5-allen.cryptic@gmail.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2020-08-18tty: ifx6x60: convert tasklets to use new tasklet_setup() APIAllen Pais
In preparation for unconditionally passing the struct tasklet_struct pointer to all tasklet callbacks, switch to using the new tasklet_setup() and from_tasklet() to pass the tasklet pointer explicitly. Signed-off-by: Romain Perier <romain.perier@gmail.com> Signed-off-by: Allen Pais <allen.lkml@gmail.com> Link: https://lore.kernel.org/r/20200817085921.26033-4-allen.cryptic@gmail.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2020-08-18tty: atmel_serial: convert tasklets to use new tasklet_setup() APIAllen Pais
In preparation for unconditionally passing the struct tasklet_struct pointer to all tasklet callbacks, switch to using the new tasklet_setup() and from_tasklet() to pass the tasklet pointer explicitly. Signed-off-by: Romain Perier <romain.perier@gmail.com> Signed-off-by: Allen Pais <allen.lkml@gmail.com> Link: https://lore.kernel.org/r/20200817085921.26033-3-allen.cryptic@gmail.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2020-08-18serial: 8250: change lock order in serial8250_do_startup()Sergey Senozhatsky
We have a number of "uart.port->desc.lock vs desc.lock->uart.port" lockdep reports coming from 8250 driver; this causes a bit of trouble to people, so let's fix it. The problem is reverse lock order in two different call paths: chain #1: serial8250_do_startup() spin_lock_irqsave(&port->lock); disable_irq_nosync(port->irq); raw_spin_lock_irqsave(&desc->lock) chain #2: __report_bad_irq() raw_spin_lock_irqsave(&desc->lock) for_each_action_of_desc() printk() spin_lock_irqsave(&port->lock); Fix this by changing the order of locks in serial8250_do_startup(): do disable_irq_nosync() first, which grabs desc->lock, and grab uart->port after that, so that chain #1 and chain #2 have same lock order. Full lockdep splat: ====================================================== WARNING: possible circular locking dependency detected 5.4.39 #55 Not tainted ====================================================== swapper/0/0 is trying to acquire lock: ffffffffab65b6c0 (console_owner){-...}, at: console_lock_spinning_enable+0x31/0x57 but task is already holding lock: ffff88810a8e34c0 (&irq_desc_lock_class){-.-.}, at: __report_bad_irq+0x5b/0xba which lock already depends on the new lock. the existing dependency chain (in reverse order) is: -> #2 (&irq_desc_lock_class){-.-.}: _raw_spin_lock_irqsave+0x61/0x8d __irq_get_desc_lock+0x65/0x89 __disable_irq_nosync+0x3b/0x93 serial8250_do_startup+0x451/0x75c uart_startup+0x1b4/0x2ff uart_port_activate+0x73/0xa0 tty_port_open+0xae/0x10a uart_open+0x1b/0x26 tty_open+0x24d/0x3a0 chrdev_open+0xd5/0x1cc do_dentry_open+0x299/0x3c8 path_openat+0x434/0x1100 do_filp_open+0x9b/0x10a do_sys_open+0x15f/0x3d7 kernel_init_freeable+0x157/0x1dd kernel_init+0xe/0x105 ret_from_fork+0x27/0x50 -> #1 (&port_lock_key){-.-.}: _raw_spin_lock_irqsave+0x61/0x8d serial8250_console_write+0xa7/0x2a0 console_unlock+0x3b7/0x528 vprintk_emit+0x111/0x17f printk+0x59/0x73 register_console+0x336/0x3a4 uart_add_one_port+0x51b/0x5be serial8250_register_8250_port+0x454/0x55e dw8250_probe+0x4dc/0x5b9 platform_drv_probe+0x67/0x8b really_probe+0x14a/0x422 driver_probe_device+0x66/0x130 device_driver_attach+0x42/0x5b __driver_attach+0xca/0x139 bus_for_each_dev+0x97/0xc9 bus_add_driver+0x12b/0x228 driver_register+0x64/0xed do_one_initcall+0x20c/0x4a6 do_initcall_level+0xb5/0xc5 do_basic_setup+0x4c/0x58 kernel_init_freeable+0x13f/0x1dd kernel_init+0xe/0x105 ret_from_fork+0x27/0x50 -> #0 (console_owner){-...}: __lock_acquire+0x118d/0x2714 lock_acquire+0x203/0x258 console_lock_spinning_enable+0x51/0x57 console_unlock+0x25d/0x528 vprintk_emit+0x111/0x17f printk+0x59/0x73 __report_bad_irq+0xa3/0xba note_interrupt+0x19a/0x1d6 handle_irq_event_percpu+0x57/0x79 handle_irq_event+0x36/0x55 handle_fasteoi_irq+0xc2/0x18a do_IRQ+0xb3/0x157 ret_from_intr+0x0/0x1d cpuidle_enter_state+0x12f/0x1fd cpuidle_enter+0x2e/0x3d do_idle+0x1ce/0x2ce cpu_startup_entry+0x1d/0x1f start_kernel+0x406/0x46a secondary_startup_64+0xa4/0xb0 other info that might help us debug this: Chain exists of: console_owner --> &port_lock_key --> &irq_desc_lock_class Possible unsafe locking scenario: CPU0 CPU1 ---- ---- lock(&irq_desc_lock_class); lock(&port_lock_key); lock(&irq_desc_lock_class); lock(console_owner); *** DEADLOCK *** 2 locks held by swapper/0/0: #0: ffff88810a8e34c0 (&irq_desc_lock_class){-.-.}, at: __report_bad_irq+0x5b/0xba #1: ffffffffab65b5c0 (console_lock){+.+.}, at: console_trylock_spinning+0x20/0x181 stack backtrace: CPU: 0 PID: 0 Comm: swapper/0 Not tainted 5.4.39 #55 Hardware name: XXXXXX Call Trace: <IRQ> dump_stack+0xbf/0x133 ? print_circular_bug+0xd6/0xe9 check_noncircular+0x1b9/0x1c3 __lock_acquire+0x118d/0x2714 lock_acquire+0x203/0x258 ? console_lock_spinning_enable+0x31/0x57 console_lock_spinning_enable+0x51/0x57 ? console_lock_spinning_enable+0x31/0x57 console_unlock+0x25d/0x528 ? console_trylock+0x18/0x4e vprintk_emit+0x111/0x17f ? lock_acquire+0x203/0x258 printk+0x59/0x73 __report_bad_irq+0xa3/0xba note_interrupt+0x19a/0x1d6 handle_irq_event_percpu+0x57/0x79 handle_irq_event+0x36/0x55 handle_fasteoi_irq+0xc2/0x18a do_IRQ+0xb3/0x157 common_interrupt+0xf/0xf </IRQ> Signed-off-by: Sergey Senozhatsky <sergey.senozhatsky@gmail.com> Fixes: 768aec0b5bcc ("serial: 8250: fix shared interrupts issues with SMP and RT kernels") Reported-by: Guenter Roeck <linux@roeck-us.net> Reported-by: Raul Rangel <rrangel@google.com> BugLink: https://bugs.chromium.org/p/chromium/issues/detail?id=1114800 Link: https://lore.kernel.org/lkml/CAHQZ30BnfX+gxjPm1DUd5psOTqbyDh4EJE=2=VAMW_VDafctkA@mail.gmail.com/T/#u Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com> Reviewed-by: Guenter Roeck <linux@roeck-us.net> Tested-by: Guenter Roeck <linux@roeck-us.net> Cc: stable <stable@vger.kernel.org> Link: https://lore.kernel.org/r/20200817022646.1484638-1-sergey.senozhatsky@gmail.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2020-08-18serial: stm32: avoid kernel warning on absence of optional IRQHolger Assmann
stm32_init_port() of the stm32-usart may trigger a warning in platform_get_irq() when the device tree specifies no wakeup interrupt. The wakeup interrupt is usually a board-specific GPIO and the driver functions correctly in its absence. The mainline stm32mp151.dtsi does not specify it, so all mainline device trees trigger an unnecessary kernel warning. Use of platform_get_irq_optional() avoids this. Fixes: 2c58e56096dd ("serial: stm32: fix the get_irq error case") Signed-off-by: Holger Assmann <h.assmann@pengutronix.de> Cc: stable <stable@vger.kernel.org> Link: https://lore.kernel.org/r/20200813152757.32751-1-h.assmann@pengutronix.de Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2020-08-18serial: pl011: Fix oops on -EPROBE_DEFERLukas Wunner
If probing of a pl011 gets deferred until after free_initmem(), an oops ensues because pl011_console_match() is called which has been freed. Fix by removing the __init attribute from the function and those it calls. Commit 10879ae5f12e ("serial: pl011: add console matching function") introduced pl011_console_match() not just for early consoles but regular preferred consoles, such as those added by acpi_parse_spcr(). Regular consoles may be registered after free_initmem() for various reasons, one being deferred probing, another being dynamic enablement of serial ports using a DeviceTree overlay. Thus, pl011_console_match() must not be declared __init and the functions it calls mustn't either. Stack trace for posterity: Unable to handle kernel paging request at virtual address 80c38b58 Internal error: Oops: 8000000d [#1] PREEMPT SMP ARM PC is at pl011_console_match+0x0/0xfc LR is at register_console+0x150/0x468 [<80187004>] (register_console) [<805a8184>] (uart_add_one_port) [<805b2b68>] (pl011_register_port) [<805b3ce4>] (pl011_probe) [<80569214>] (amba_probe) [<805ca088>] (really_probe) [<805ca2ec>] (driver_probe_device) [<805ca5b0>] (__device_attach_driver) [<805c8060>] (bus_for_each_drv) [<805c9dfc>] (__device_attach) [<805ca630>] (device_initial_probe) [<805c90a8>] (bus_probe_device) [<805c95a8>] (deferred_probe_work_func) Fixes: 10879ae5f12e ("serial: pl011: add console matching function") Signed-off-by: Lukas Wunner <lukas@wunner.de> Cc: stable@vger.kernel.org # v4.10+ Cc: Aleksey Makarov <amakarov@marvell.com> Cc: Peter Hurley <peter@hurleysoftware.com> Cc: Russell King <linux@armlinux.org.uk> Cc: Christopher Covington <cov@codeaurora.org> Link: https://lore.kernel.org/r/f827ff09da55b8c57d316a1b008a137677b58921.1597315557.git.lukas@wunner.de Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2020-08-18serial: pl011: Don't leak amba_ports entry on driver register errorLukas Wunner
pl011_probe() calls pl011_setup_port() to reserve an amba_ports[] entry, then calls pl011_register_port() to register the uart driver with the tty layer. If registration of the uart driver fails, the amba_ports[] entry is not released. If this happens 14 times (value of UART_NR macro), then all amba_ports[] entries will have been leaked and driver probing is no longer possible. (To be fair, that can only happen if the DeviceTree doesn't contain alias IDs since they cause the same entry to be used for a given port.) Fix it. Fixes: ef2889f7ffee ("serial: pl011: Move uart_register_driver call to device") Signed-off-by: Lukas Wunner <lukas@wunner.de> Cc: stable@vger.kernel.org # v3.15+ Cc: Tushar Behera <tushar.behera@linaro.org> Link: https://lore.kernel.org/r/138f8c15afb2f184d8102583f8301575566064a6.1597316167.git.lukas@wunner.de Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2020-08-18serial: 8250_exar: Fix number of ports for Commtech PCIe cardsValmer Huhn
The following in 8250_exar.c line 589 is used to determine the number of ports for each Exar board: nr_ports = board->num_ports ? board->num_ports : pcidev->device & 0x0f; If the number of ports a card has is not explicitly specified, it defaults to the rightmost 4 bits of the PCI device ID. This is prone to error since not all PCI device IDs contain a number which corresponds to the number of ports that card provides. This particular case involves COMMTECH_4222PCIE, COMMTECH_4224PCIE and COMMTECH_4228PCIE cards with device IDs 0x0022, 0x0020 and 0x0021. Currently the multiport cards receive 2, 0 and 1 port instead of 2, 4 and 8 ports respectively. To fix this, each Commtech Fastcom PCIe card is given a struct where the number of ports is explicitly specified. This ensures 'board->num_ports' is used instead of the default 'pcidev->device & 0x0f'. Fixes: d0aeaa83f0b0 ("serial: exar: split out the exar code from 8250_pci") Signed-off-by: Valmer Huhn <valmer.huhn@concurrent-rt.com> Tested-by: Valmer Huhn <valmer.huhn@concurrent-rt.com> Cc: stable <stable@vger.kernel.org> Link: https://lore.kernel.org/r/20200813165255.GC345440@icarus.concurrent-rt.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2020-08-18tty: serial: qcom_geni_serial: Drop __init from qcom_geni_console_setupJohn Stultz
When booting with heavily modularized config, the serial console may not be able to load until after init when modules that satisfy needed dependencies have time to load. Unfortunately, as qcom_geni_console_setup is marked as __init, the function may have been freed before we get to run it, causing boot time crashes such as: [ 6.469057] Unable to handle kernel paging request at virtual address ffffffe645d4e6cc [ 6.481623] Mem abort info: [ 6.484466] ESR = 0x86000007 [ 6.487557] EC = 0x21: IABT (current EL), IL = 32 bits [ 6.492929] SET = 0, FnV = 0g [ 6.496016] EA = 0, S1PTW = 0 [ 6.499202] swapper pgtable: 4k pages, 39-bit VAs, pgdp=000000008151e000 [ 6.501286] ufshcd-qcom 1d84000.ufshc: ufshcd_print_pwr_info:[RX, TX]: gear=[3, 3], lane[2, 2], pwr[FAST MODE, FAST MODE], rate = 2 [ 6.505977] [ffffffe645d4e6cc] pgd=000000017df9f003, p4d=000000017df9f003, pud=000000017df9f003, pmd=000000017df9c003, pte=0000000000000000 [ 6.505990] Internal error: Oops: 86000007 [#1] PREEMPT SMP [ 6.505995] Modules linked in: zl10353 zl10039 zl10036 zd1301_demod xc5000 xc4000 ves1x93 ves1820 tuner_xc2028 tuner_simple tuner_types tua9001 tua6100 1 [ 6.506152] isl6405 [ 6.518104] ufshcd-qcom 1d84000.ufshc: ufshcd_find_max_sup_active_icc_level: Regulator capability was not set, actvIccLevel=0 [ 6.530549] horus3a helene fc2580 fc0013 fc0012 fc0011 ec100 e4000 dvb_pll ds3000 drxk drxd drx39xyj dib9000 dib8000 dib7000p dib7000m dib3000mc dibx003 [ 6.624271] CPU: 7 PID: 148 Comm: kworker/7:2 Tainted: G W 5.8.0-mainline-12021-g6defd37ba1cd #3455 [ 6.624273] Hardware name: Thundercomm Dragonboard 845c (DT) [ 6.624290] Workqueue: events deferred_probe_work_func [ 6.624296] pstate: 40c00005 (nZcv daif +PAN +UAO BTYPE=--) [ 6.624307] pc : qcom_geni_console_setup+0x0/0x110 [ 6.624316] lr : try_enable_new_console+0xa0/0x140 [ 6.624318] sp : ffffffc010843a30 [ 6.624320] x29: ffffffc010843a30 x28: ffffffe645c3e7d0 [ 6.624325] x27: ffffff80f8022180 x26: ffffffc010843b28 [ 6.637937] x25: 0000000000000000 x24: ffffffe6462a2000 [ 6.637941] x23: ffffffe646398000 x22: 0000000000000000 [ 6.637945] x21: 0000000000000000 x20: ffffffe6462a5ce8 [ 6.637952] x19: ffffffe646398e38 x18: ffffffffffffffff [ 6.680296] x17: 0000000000000000 x16: ffffffe64492b900 [ 6.680300] x15: ffffffe6461e9d08 x14: 69202930203d2064 [ 6.680305] x13: 7561625f65736162 x12: 202c363331203d20 [ 6.696434] x11: 0000000000000030 x10: 0101010101010101 [ 6.696438] x9 : 4d4d20746120304d x8 : 7f7f7f7f7f7f7f7f [ 6.707249] x7 : feff4c524c787373 x6 : 0000000000008080 [ 6.707253] x5 : 0000000000000000 x4 : 8080000000000000 [ 6.707257] x3 : 0000000000000000 x2 : ffffffe645d4e6cc [ 6.744223] qcom_geni_serial 898000.serial: dev_pm_opp_set_rate: failed to find OPP for freq 102400000 (-34) [ 6.744966] x1 : fffffffefe74e174 x0 : ffffffe6462a5ce8 [ 6.753580] qcom_geni_serial 898000.serial: dev_pm_opp_set_rate: failed to find OPP for freq 102400000 (-34) [ 6.761634] Call trace: [ 6.761639] qcom_geni_console_setup+0x0/0x110 [ 6.761645] register_console+0x29c/0x2f8 [ 6.767981] Bluetooth: hci0: Frame reassembly failed (-84) [ 6.775252] uart_add_one_port+0x438/0x500 [ 6.775258] qcom_geni_serial_probe+0x2c4/0x4a8 [ 6.775266] platform_drv_probe+0x58/0xa8 [ 6.855359] really_probe+0xec/0x398 [ 6.855362] driver_probe_device+0x5c/0xb8 [ 6.855367] __device_attach_driver+0x98/0xb8 [ 7.184945] bus_for_each_drv+0x74/0xd8 [ 7.188825] __device_attach+0xec/0x148 [ 7.192705] device_initial_probe+0x24/0x30 [ 7.196937] bus_probe_device+0x9c/0xa8 [ 7.200816] deferred_probe_work_func+0x7c/0xb8 [ 7.205398] process_one_work+0x20c/0x4b0 [ 7.209456] worker_thread+0x48/0x460 [ 7.213157] kthread+0x14c/0x158 [ 7.216432] ret_from_fork+0x10/0x18 [ 7.220049] Code: bad PC value [ 7.223139] ---[ end trace 73f3b21e251d5a70 ]--- Thus this patch removes the __init avoiding crash in such configs. Cc: Andy Gross <agross@kernel.org> Cc: Jiri Slaby <jirislaby@kernel.org> Cc: Saravana Kannan <saravanak@google.com> Cc: Todd Kjos <tkjos@google.com> Cc: Amit Pundir <amit.pundir@linaro.org> Cc: linux-arm-msm@vger.kernel.org Cc: linux-serial@vger.kernel.org Suggested-by: Saravana Kannan <saravanak@google.com> Signed-off-by: John Stultz <john.stultz@linaro.org> Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org> Link: https://lore.kernel.org/r/20200811025044.70626-1-john.stultz@linaro.org Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2020-08-18serial: qcom_geni_serial: Fix recent kdb hangDouglas Anderson
The commit e42d6c3ec0c7 ("serial: qcom_geni_serial: Make kgdb work even if UART isn't console") worked pretty well and I've been doing a lot of debugging with it. However, recently I typed "dmesg" in kdb and then held the space key down to scroll through the pagination. My device hung. This was repeatable and I found that it was introduced with the aforementioned commit. It turns out that there are some strange boundary cases in geni where in some weird situations it will signal RX_LAST but then will put 0 in RX_LAST_BYTE. This means that the entire last FIFO entry is valid. This weird corner case is handled in qcom_geni_serial_handle_rx() where you can see that we only honor RX_LAST_BYTE if RX_LAST is set _and_ RX_LAST_BYTE is non-zero. If either of these is not true we use BYTES_PER_FIFO_WORD (4) for the size of the last FIFO word. Let's fix kgdb. While at it, also use the proper #define for 4. Fixes: e42d6c3ec0c7 ("serial: qcom_geni_serial: Make kgdb work even if UART isn't console") Signed-off-by: Douglas Anderson <dianders@chromium.org> Reviewed-by: Akash Asthana <akashast@codeaurora.org> Link: https://lore.kernel.org/r/20200806221904.1.I4455ff86f0ef5281c2a0cd0a4712db614548a5ca@changeid Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2020-08-06Merge tag 'tty-5.9-rc1' of ↵Linus Torvalds
git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty Pull tty/serial updates from Greg KH: "Here is the large set of TTY and Serial driver patches for 5.9-rc1. Lots of bugfixes in here, thanks to syzbot fuzzing for serial and vt and console code. Other highlights include: - much needed vt/vc code cleanup from Jiri Slaby - 8250 driver fixes and additions - various serial driver updates and feature enhancements - locking cleanup for serial/console initializations - other minor cleanups All of these have been in linux-next with no reported issues" * tag 'tty-5.9-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty: (90 commits) MAINTAINERS: enlist Greg formally for console stuff vgacon: Fix for missing check in scrollback handling Revert "serial: 8250: Let serial core initialise spin lock" serial: 8250: Let serial core initialise spin lock tty: keyboard, do not speculate on func_table index serial: stm32: Add RS485 RTS GPIO control serial: 8250_dw: Fix common clocks usage race condition serial: 8250_dw: Pass the same rate to the clk round and set rate methods serial: 8250_dw: Simplify the ref clock rate setting procedure serial: 8250: Add 8250 port clock update method tty: serial: imx: add imx earlycon driver tty: serial: imx: enable imx serial console port as module tty/synclink: remove leftover bits of non-PCI card support tty: Use the preferred form for passing the size of a structure type tty: Fix identation issues in struct serial_struct32 tty: Avoid the use of one-element arrays serial: msm_serial: add sparse context annotation serial: pmac_zilog: add sparse context annotation newport_con: vc_color is now in state serial: imx: use hrtimers for rs485 delays ...
2020-08-06Merge tag 'sched-fifo-2020-08-04' of ↵Linus Torvalds
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip Pull sched/fifo updates from Ingo Molnar: "This adds the sched_set_fifo*() encapsulation APIs to remove static priority level knowledge from non-scheduler code. The three APIs for non-scheduler code to set SCHED_FIFO are: - sched_set_fifo() - sched_set_fifo_low() - sched_set_normal() These are two FIFO priority levels: default (high), and a 'low' priority level, plus sched_set_normal() to set the policy back to non-SCHED_FIFO. Since the changes affect a lot of non-scheduler code, we kept this in a separate tree" * tag 'sched-fifo-2020-08-04' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (24 commits) sched,tracing: Convert to sched_set_fifo() sched: Remove sched_set_*() return value sched: Remove sched_setscheduler*() EXPORTs sched,psi: Convert to sched_set_fifo_low() sched,rcutorture: Convert to sched_set_fifo_low() sched,rcuperf: Convert to sched_set_fifo_low() sched,locktorture: Convert to sched_set_fifo() sched,irq: Convert to sched_set_fifo() sched,watchdog: Convert to sched_set_fifo() sched,serial: Convert to sched_set_fifo() sched,powerclamp: Convert to sched_set_fifo() sched,ion: Convert to sched_set_normal() sched,powercap: Convert to sched_set_fifo*() sched,spi: Convert to sched_set_fifo*() sched,mmc: Convert to sched_set_fifo*() sched,ivtv: Convert to sched_set_fifo*() sched,drm/scheduler: Convert to sched_set_fifo*() sched,msm: Convert to sched_set_fifo*() sched,psci: Convert to sched_set_fifo*() sched,drbd: Convert to sched_set_fifo*() ...
2020-08-04Merge tag 'printk-for-5.9' of ↵Linus Torvalds
git://git.kernel.org/pub/scm/linux/kernel/git/printk/linux Pull printk updates from Petr Mladek: - Herbert Xu made printk header file self-contained. - Andy Shevchenko and Sergey Senozhatsky cleaned up console->setup() error handling. - Andy Shevchenko did some cleanups (e.g. sparse warning) in vsprintf code. - Minor documentation updates. * tag 'printk-for-5.9' of git://git.kernel.org/pub/scm/linux/kernel/git/printk/linux: lib/vsprintf: Force type of flags value for gfp_t lib/vsprintf: Replace custom spec to print decimals with generic one lib/vsprintf: Replace hidden BUILD_BUG_ON() with static_assert() printk: Make linux/printk.h self-contained doc:kmsg: explicitly state the return value in case of SEEK_CUR Replace HTTP links with HTTPS ones: vsprintf hvc: unify console setup naming console: Fix trivia typo 'change' -> 'chance' console: Propagate error code from console ->setup() tty: hvc: Return proper error code from console ->setup() hook serial: sunzilog: Return proper error code from console ->setup() hook serial: sunsab: Return proper error code from console ->setup() hook mips: Return proper error code from console ->setup() hook
2020-08-03Merge tag 'arm-drivers-5.9' of ↵Linus Torvalds
git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc Pull ARM SoC driver updates from Arnd Bergmann: "A couple of subsystems have their own subsystem maintainers but choose to have the code merged through the soc tree as upstream, as the code tends to be used across multiple SoCs or has SoC specific drivers itself: - memory controllers: Krzysztof Kozlowski takes ownership of the drivers/memory subsystem and its drivers, starting out with a set of cleanup patches. A larger driver for the Tegra memory controller that was accidentally missed for v5.8 is now added. - reset controllers: Only minor updates to drivers/reset this time - firmware: The "turris mox" firmware driver gains support for signed firmware blobs The tegra firmware driver gets extended to export some debug information Various updates to i.MX firmware drivers, mostly cosmetic - ARM SCMI/SCPI: A new mechanism for platform notifications is added, among a number of minor changes. - optee: Probing of the TEE bus is rewritten to better support detection of devices that depend on the tee-supplicant user space. A new firmware based trusted platform module (fTPM) driver is added based on OP-TEE - SoC attributes: A new driver is added to provide a generic soc_device for identifying a machine through the SMCCC ARCH_SOC_ID firmware interface rather than by probing SoC family specific registers. The series also contains some cleanups to the common soc_device code. There are also a number of updates to SoC specific drivers, the main ones are: - Mediatek cmdq driver gains a few in-kernel interfaces - Minor updates to Qualcomm RPMh, socinfo, rpm drivers, mostly adding support for additional SoC variants - The Qualcomm GENI core code gains interconnect path voting and performance level support, and integrating this into a number of device drivers. - A new driver for Samsung Exynos5800 voltage coupler for - Renesas RZ/G2H (R8A774E1) SoC support gets added to a couple of SoC specific device drivers - Updates to the TI K3 Ring Accelerator driver" * tag 'arm-drivers-5.9' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc: (164 commits) soc: qcom: geni: Fix unused label warning soc: qcom: smd-rpm: Fix kerneldoc memory: jz4780_nemc: Only request IO memory the driver will use soc: qcom: pdr: Reorder the PD state indication ack MAINTAINERS: Add Git repository for memory controller drivers memory: brcmstb_dpfe: Fix language typo memory: samsung: exynos5422-dmc: Correct white space issues memory: samsung: exynos-srom: Correct alignment memory: pl172: Enclose macro argument usage in parenthesis memory: of: Correct kerneldoc memory: omap-gpmc: Fix language typo memory: omap-gpmc: Correct white space issues memory: omap-gpmc: Use 'unsigned int' for consistency memory: omap-gpmc: Enclose macro argument usage in parenthesis memory: omap-gpmc: Correct kerneldoc memory: mvebu-devbus: Align with open parenthesis memory: mvebu-devbus: Add missing braces to all arms of if statement memory: bt1-l2-ctl: Add blank lines after declarations soc: TI knav_qmss: make symbol 'knav_acc_range_ops' static firmware: ti_sci: Replace HTTP links with HTTPS ones ...
2020-08-02Revert "serial: 8250: Let serial core initialise spin lock"Andy Shevchenko
This reverts commit 679193b7baf8d88e41cbeb397ca17f797654947d. It appears that in QEmu the lock has been initialised differently (it wasn't obvious on real hardware during testing). Let's revert the change until the better approach will be developed. Reported-by: kernel test robot <lkp@intel.com> Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com> Link: https://lore.kernel.org/r/20200802111612.36189-1-andriy.shevchenko@linux.intel.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2020-07-31serial: 8250: Let serial core initialise spin lockAndy Shevchenko
Since the serial core handles spin lock initialisation, let the driver rely on it. Depends-on: f743061a85f5 ("serial: core: Initialise spin lock before use in uart_configure_port()") Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com> Link: https://lore.kernel.org/r/20200731123733.22754-1-andriy.shevchenko@linux.intel.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2020-07-30serial: stm32: Add RS485 RTS GPIO controlMarek Vasut
While the STM32 does support RS485 drive-enable control within the UART IP itself, some systems have the drive-enable line connected to a pin which cannot be pinmuxed as RTS. Add support for toggling the RTS GPIO line using the modem control GPIOs to provide at least some sort of emulation. Signed-off-by: Marek Vasut <marex@denx.de> Cc: Alexandre Torgue <alexandre.torgue@st.com> Cc: Andy Shevchenko <andy.shevchenko@gmail.com> Cc: Manivannan Sadhasivam <mani@kernel.org> Cc: Fabrice Gasnier <fabrice.gasnier@st.com> Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Cc: linux-stm32@st-md-mailman.stormreply.com Link: https://lore.kernel.org/r/20200725144947.537007-1-marex@denx.de Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
generated by cgit v1.2.3 (git 2.39.1) at 2025-08-04 14:36:37 +0000