summaryrefslogtreecommitdiff
path: root/drivers/tty/serial
AgeCommit message (Collapse)Author
2023-01-31tty: serial: fsl_lpuart: Fix the wrong RXWATER setting for rx dma caseSherry Sun
The RXWATER value must be greater than 0 according to the LPUART reference manual. And when the number of datawords in the receive FIFO is greater than RXWATER, an interrupt or a DMA request is generated, so no need to set the different value for lpuart interrupt case and dma case. Here delete the wrong RXWATER setting for dma case directly. Fixes: 42b68768e51b ("serial: fsl_lpuart: DMA support for 32-bit variant") Signed-off-by: Sherry Sun <sherry.sun@nxp.com> Link: https://lore.kernel.org/r/20230130064449.9564-4-sherry.sun@nxp.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2023-01-31tty: serial: fsl_lpuart: set receive watermark for imx8qxp platformSherry Sun
Since imx8qxp RX FIFO depth is 64 datawords, it will be better to set the rx watermark as 31, which means when the number of datawords in the receive FIFO(>= 32) is greater than the watermark, an interrupt or a DMA request is generated. Also keep the console rx watermark as 1 to make sure it responsive. Signed-off-by: Sherry Sun <sherry.sun@nxp.com> Link: https://lore.kernel.org/r/20230130064449.9564-3-sherry.sun@nxp.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2023-01-31tty: serial: fsl_lpuart: make rx_watermark configurable for different platformsSherry Sun
Add rx_watermark parameter for struct lpuart_port to make the receive watermark configurable for different platforms. No function changed. Signed-off-by: Sherry Sun <sherry.sun@nxp.com> Link: https://lore.kernel.org/r/20230130064449.9564-2-sherry.sun@nxp.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2023-01-31tty: serial: fsl_lpuart: don't enable receiver/transmitter before rx/tx dma ↵Sherry Sun
ready lpuart32_setup_watermark_enable() will configure the UART FIFO and watermark, also enable the receiver and transmitter, this should be done after the rx/tx dma steup ready. Also add lpuart32_hw_disable() to make sure the receiver/transmitter and interrupts are disabled during the dma steup. Signed-off-by: Sherry Sun <sherry.sun@nxp.com> Link: https://lore.kernel.org/r/20230130054107.9119-1-sherry.sun@nxp.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2023-01-23serial: liteuart: Correct error rollbackIlpo Järvinen
Goto to the correct rollback label instead of directly returning. Fixes: 5602cf99dcdc ("serial: liteuart: add IRQ support for the RX path") Reported-by: Stephen Rothwell <sfr@canb.auug.org.au> Reported-by: kernel test robot <lkp@intel.com> Reported-by: Dan Carpenter <error27@gmail.com> Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com> Reviewed-by: Gabriel Somlo <gsomlo@gmail.com> Link: https://lore.kernel.org/r/20230123173857.40695-3-ilpo.jarvinen@linux.intel.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2023-01-23serial: qcom_geni: Fix variable namingIlpo Järvinen
Commit 2aaa43c70778 ("tty: serial: qcom-geni-serial: add support for serial engine DMA") renamed rx_fifo member to rf_buf which caused a build failure when b8caf69a6946 ("tty: serial: qcom-geni-serial: fix slab-out-of-bounds on RX FIFO buffer") from tty-linus was merged into tty-next. Fix the member variable name. Fixes: 7a6aa989f2e8 ("Merge 6.2-rc5 into tty-next") Reported-by: Stephen Rothwell <sfr@canb.auug.org.au> Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com> Link: https://lore.kernel.org/r/20230123173857.40695-2-ilpo.jarvinen@linux.intel.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2023-01-22Merge 6.2-rc5 into driver-core-nextGreg Kroah-Hartman
We need the driver core fixes in here as well. Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2023-01-22Merge 6.2-rc5 into tty-nextGreg Kroah-Hartman
We need the serial/tty changes into this branch as well. Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2023-01-21Merge tag 'tty-6.2-rc5' of ↵Linus Torvalds
git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty Pull tty/serial driver fixes from Greg KH: "Here are some small tty and serial driver fixes for 6.2-rc5 that resolve a number of tiny reported issues and some new device ids. They include: - new device id for the exar serial driver - speakup tty driver bugfix - atmel serial driver baudrate fixup - stm32 serial driver bugfix and then revert as the bugfix broke the build. That will come back in a later pull request once it is all worked out properly. - amba-pl011 serial driver rs486 mode bugfix - qcom_geni serial driver bugfix Most of these have been in linux-next with no reported problems (well, other than the build breakage which generated the revert), the new device id passed 0-day testing" * tag 'tty-6.2-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty: serial: exar: Add support for Sealevel 7xxxC serial cards Revert "serial: stm32: Merge hard IRQ and threaded IRQ handling into single IRQ handler" tty: serial: qcom_geni: avoid duplicate struct member init serial: atmel: fix incorrect baudrate setup tty: fix possible null-ptr-defer in spk_ttyio_release serial: stm32: Merge hard IRQ and threaded IRQ handling into single IRQ handler serial: amba-pl011: fix high priority character transmission in rs486 mode serial: pch_uart: Pass correct sg to dma_unmap_sg() tty: serial: qcom-geni-serial: fix slab-out-of-bounds on RX FIFO buffer
2023-01-20serial: exar: Add support for Sealevel 7xxxC serial cardsMatthew Howell
Add support for Sealevel 7xxxC serial cards. This patch: * Adds IDs to recognize 7xxxC cards from Sealevel Systems. * Updates exar_pci_probe() to set nr_ports to last two bytes of primary dev ID for these cards. Signed-off-by: Matthew Howell <matthew.howell@sealevel.com> Cc: stable <stable@kernel.org> Link: https://lore.kernel.org/r/alpine.DEB.2.21.2301191440010.22558@tstest-VirtualBox Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2023-01-20Revert "serial: stm32: Merge hard IRQ and threaded IRQ handling into single ↵Greg Kroah-Hartman
IRQ handler" This reverts commit f24771b62a83239f0dce816bddf0f6807f436235 as it is reported to break the build. Reported-by: kernel test robot <lkp@intel.com> Link: https://lore.kernel.org/r/202301200130.ttBiTzfO-lkp@intel.com Fixes: f24771b62a83 ("serial: stm32: Merge hard IRQ and threaded IRQ handling into single IRQ handler") Cc: Sebastian Andrzej Siewior <bigeasy@linutronix.de> Cc: Valentin Caron <valentin.caron@foss.st.com> # V3 Cc: Marek Vasut <marex@denx.de> Cc: Johan Hovold <johan@kernel.org> Cc: stable@vger.kernel.org Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2023-01-19Merge tag 'printk-for-6.2-rc5' of ↵Linus Torvalds
git://git.kernel.org/pub/scm/linux/kernel/git/printk/linux Pull printk fixes from Petr Mladek: - Prevent a potential deadlock when configuring kgdb console - Fix a kernel doc warning * tag 'printk-for-6.2-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/printk/linux: kernel/printk/printk.c: Fix W=1 kernel-doc warning tty: serial: kgdboc: fix mutex locking order for configure_kgdboc()
2023-01-19tty: serial: qcom_geni: avoid duplicate struct member initArnd Bergmann
When -Woverride-init is enabled in a build, gcc points out that qcom_geni_serial_pm_ops contains conflicting initializers: drivers/tty/serial/qcom_geni_serial.c:1586:20: error: initialized field overwritten [-Werror=override-init] 1586 | .restore = qcom_geni_serial_sys_hib_resume, | ^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~ drivers/tty/serial/qcom_geni_serial.c:1586:20: note: (near initialization for 'qcom_geni_serial_pm_ops.restore') drivers/tty/serial/qcom_geni_serial.c:1587:17: error: initialized field overwritten [-Werror=override-init] 1587 | .thaw = qcom_geni_serial_sys_hib_resume, | ^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~ Open-code the initializers with the version that was already used, and use the pm_sleep_ptr() method to deal with unused ones, in place of the __maybe_unused annotation. Fixes: 35781d8356a2 ("tty: serial: qcom-geni-serial: Add support for Hibernation feature") Signed-off-by: Arnd Bergmann <arnd@arndb.de> Reviewed-by: Douglas Anderson <dianders@chromium.org> Link: https://lore.kernel.org/r/20221215165453.1864836-1-arnd@kernel.org Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2023-01-19serial: atmel: fix incorrect baudrate setupTobias Schramm
Commit ba47f97a18f2 ("serial: core: remove baud_rates when serial console setup") changed uart_set_options to select the correct baudrate configuration based on the absolute error between requested baudrate and available standard baudrate settings. Prior to that commit the baudrate was selected based on which predefined standard baudrate did not exceed the requested baudrate. This change of selection logic was never reflected in the atmel serial driver. Thus the comment left in the atmel serial driver is no longer accurate. Additionally the manual rounding up described in that comment and applied via (quot - 1) requests an incorrect baudrate. Since uart_set_options uses tty_termios_encode_baud_rate to determine the appropriate baudrate flags this can cause baudrate selection to fail entirely because tty_termios_encode_baud_rate will only select a baudrate if relative error between requested and selected baudrate does not exceed +/-2%. Fix that by requesting actual, exact baudrate used by the serial. Fixes: ba47f97a18f2 ("serial: core: remove baud_rates when serial console setup") Cc: stable <stable@kernel.org> Signed-off-by: Tobias Schramm <t.schramm@manjaro.org> Acked-by: Richard Genoud <richard.genoud@gmail.com> Link: https://lore.kernel.org/r/20230109072940.202936-1-t.schramm@manjaro.org Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2023-01-19tty: serial: 8250: add DFL bus driver for Altera 16550.Matthew Gerlach
Add a Device Feature List (DFL) bus driver for the Altera 16550 implementation of UART. Signed-off-by: Matthew Gerlach <matthew.gerlach@linux.intel.com> Reviewed-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com> Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com> Reviewed-by: Marco Pagani <marpagan@redhat.com> Link: https://lore.kernel.org/r/20230115151447.1353428-5-matthew.gerlach@linux.intel.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2023-01-19tty: Call ->dtr_rts() parameter active consistentlyIlpo Järvinen
Convert various parameter names for ->dtr_rts() and related functions from onoff, on, and raise to active. Reviewed-by: Jiri Slaby <jirislaby@kernel.org> Acked-by: Ulf Hansson <ulf.hansson@linaro.org> # For MMC Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com> Link: https://lore.kernel.org/r/20230117090358.4796-12-ilpo.jarvinen@linux.intel.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2023-01-19serial: Make uart_handle_cts_change() status param bool activeIlpo Järvinen
Convert uart_handle_cts_change() to bool which is more appropriate than unsigned int. Rename status to active to better describe what the parameter means. While at it, make the comment about the active parameter easier to parse. Cleanup callsites from operations that are not necessary with bool. Reviewed-by: Jiri Slaby <jirislaby@kernel.org> Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com> Link: https://lore.kernel.org/r/20230117090358.4796-10-ilpo.jarvinen@linux.intel.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2023-01-19tty/serial: Make ->dcd_change()+uart_handle_dcd_change() status bool activeIlpo Järvinen
Convert status parameter for ->dcd_change() and uart_handle_dcd_change() to bool which matches to how the parameter is used. Rename status to active to better describe what the parameter means. Acked-by: Rodolfo Giometti <giometti@enneenne.com> Reviewed-by: Jiri Slaby <jirislaby@kernel.org> Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com> Link: https://lore.kernel.org/r/20230117090358.4796-9-ilpo.jarvinen@linux.intel.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2023-01-19tty: Convert ->dtr_rts() to take bool argumentIlpo Järvinen
Convert the raise/on parameter in ->dtr_rts() to bool through the callchain. The parameter is used like bool. In USB serial, there remains a few implicit bool -> larger type conversions because some devices use u8 in their control messages. In moxa_tiocmget(), dtr variable was reused for line status which requires int so use a separate variable for status. Reviewed-by: Jiri Slaby <jirislaby@kernel.org> Acked-by: Ulf Hansson <ulf.hansson@linaro.org> # For MMC Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com> Link: https://lore.kernel.org/r/20230117090358.4796-8-ilpo.jarvinen@linux.intel.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2023-01-19tty: Convert ->carrier_raised() and callchains to boolIlpo Järvinen
Return boolean from ->carrier_raised() instead of 0 and 1. Make the return type change also to tty_port_carrier_raised() that makes the ->carrier_raised() call (+ cd variable in moxa into which its return value is stored). Also cleans up a few unnecessary constructs related to this change: return xx ? 1 : 0; -> return xx; if (xx) return 1; return 0; -> return xx; Reviewed-by: Jiri Slaby <jirislaby@kernel.org> Acked-by: Ulf Hansson <ulf.hansson@linaro.org> # For MMC Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com> Link: https://lore.kernel.org/r/20230117090358.4796-7-ilpo.jarvinen@linux.intel.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2023-01-19serial: Convert uart_{,port_}startup() init_hw param to boolIlpo Järvinen
Convert init_hw parameter in uart_startup() and uart_port_startup() to bool as code treats them like bool. Reviewed-by: Jiri Slaby <jirislaby@kernel.org> Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com> Link: https://lore.kernel.org/r/20230117090358.4796-6-ilpo.jarvinen@linux.intel.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2023-01-19tty: Cleanup tty_port_set_active() bool parameterIlpo Järvinen
Make callers pass true/false consistently for bool val. Reviewed-by: Jiri Slaby <jirislaby@kernel.org> Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com> Link: https://lore.kernel.org/r/20230117090358.4796-4-ilpo.jarvinen@linux.intel.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2023-01-19tty: Cleamup tty_port_set_suspended() bool parameterIlpo Järvinen
Make callers pass true/false consistently for bool val. Reviewed-by: Jiri Slaby <jirislaby@kernel.org> Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com> Link: https://lore.kernel.org/r/20230117090358.4796-3-ilpo.jarvinen@linux.intel.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2023-01-19tty: Cleanup tty_port_set_initialized() bool parameterIlpo Järvinen
Make callers pass true/false consistently for bool val. Reviewed-by: Samuel Iglesias Gonsalvez <siglesias@igalia.com> Reviewed-by: Jiri Slaby <jirislaby@kernel.org> Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com> Link: https://lore.kernel.org/r/20230117090358.4796-2-ilpo.jarvinen@linux.intel.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2023-01-19serial: pic32: Add checks for devm_clk_get() in pic32_uart_probe()Yuan Can
As the devm_clk_get() may return ERR_PTR, its return value needs to be checked to avoid invalid poineter dereference. Signed-off-by: Yuan Can <yuancan@huawei.com> Link: https://lore.kernel.org/r/20221125093832.33386-1-yuancan@huawei.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2023-01-19serial: stm32: Add support for rs485 RX_DURING_TX output GPIOChristoph Niedermaier
If a RX_DURING_TX GPIO is defined by the DT property "rs485-rx-during-tx-gpios" this patch switches this GPIO accordingly to the RS485 flag RX_DURING_TX in user space. Controlled by this GPIO, now the hardware is responsible for connecting or disconnecting RX during TX. Signed-off-by: Christoph Niedermaier <cniedermaier@dh-electronics.com> Link: https://lore.kernel.org/r/20221202104127.122761-4-cniedermaier@dh-electronics.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2023-01-19serial: imx: Add support for RS485 RX_DURING_TX output GPIOChristoph Niedermaier
If a RX_DURING_TX GPIO is defined by the DT property "rs485-rx-during-tx-gpios" this patch switches this GPIO accordingly to the RS485 flag RX_DURING_TX in user space. In addition, the i.MX UART receiver is no longer turned on and off during sending, because now the hardware is responsible for connecting or disconnecting RX during TX controlled by this GPIO. Signed-off-by: Christoph Niedermaier <cniedermaier@dh-electronics.com> Link: https://lore.kernel.org/r/20221202104127.122761-3-cniedermaier@dh-electronics.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2023-01-19serial: core: Add option to output RS485 RX_DURING_TX state via GPIOChristoph Niedermaier
This patch provides a generic GPIO variable for outputting the state of RS485 RX_DURING_TX. The GPIO is defined by the devicetree property "rs485-rx-during-tx-gpios". To use it in a low level serial driver, the evaluation of this variable must be implemented there accordingly. Signed-off-by: Christoph Niedermaier <cniedermaier@dh-electronics.com> Link: https://lore.kernel.org/r/20221202104127.122761-2-cniedermaier@dh-electronics.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2023-01-19serial: tegra: Add missing clk_disable_unprepare() in tegra_uart_hw_init()Yi Yang
Add the missing clk_disable_unprepare() before return from tegra_uart_hw_init() in the error handling path. When request_irq() fails in tegra_uart_startup(), 'tup->uart_clk' has been enabled, fix it by adding clk_disable_unprepare(). Fixes: cc9ca4d95846 ("serial: tegra: Only print FIFO error message when an error occurs") Fixes: d781ec21bae6 ("serial: tegra: report clk rate errors") Signed-off-by: Yi Yang <yiyang13@huawei.com> Link: https://lore.kernel.org/r/20221126020852.113378-1-yiyang13@huawei.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2023-01-19serial: sc16is7xx: setup GPIO controller later in probeIsaac True
The GPIO controller component of the sc16is7xx driver is setup too early, which can result in a race condition where another device tries to utilise the GPIO lines before the sc16is7xx device has finished initialising. This issue manifests itself as an Oops when the GPIO lines are configured: Unable to handle kernel read from unreadable memory at virtual address ... pc : sc16is7xx_gpio_direction_output+0x68/0x108 [sc16is7xx] lr : sc16is7xx_gpio_direction_output+0x4c/0x108 [sc16is7xx] ... Call trace: sc16is7xx_gpio_direction_output+0x68/0x108 [sc16is7xx] gpiod_direction_output_raw_commit+0x64/0x318 gpiod_direction_output+0xb0/0x170 create_gpio_led+0xec/0x198 gpio_led_probe+0x16c/0x4f0 platform_drv_probe+0x5c/0xb0 really_probe+0xe8/0x448 driver_probe_device+0xe8/0x138 __device_attach_driver+0x94/0x118 bus_for_each_drv+0x8c/0xe0 __device_attach+0x100/0x1b8 device_initial_probe+0x28/0x38 bus_probe_device+0xa4/0xb0 deferred_probe_work_func+0x90/0xe0 process_one_work+0x1c4/0x480 worker_thread+0x54/0x430 kthread+0x138/0x150 ret_from_fork+0x10/0x1c This patch moves the setup of the GPIO controller functions to later in the probe function, ensuring the sc16is7xx device has already finished initialising by the time other devices try to make use of the GPIO lines. The error handling has also been reordered to reflect the new initialisation order. Co-developed-by: Wen-chien Jesse Sung <jesse.sung@canonical.com> Signed-off-by: Wen-chien Jesse Sung <jesse.sung@canonical.com> Signed-off-by: Isaac True <isaac.true@canonical.com> Link: https://lore.kernel.org/r/20221130105529.698385-1-isaac.true@canonical.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2023-01-19serial: msm: add lock annotation to msm_set_baud_rate()Krzysztof Kozlowski
msm_set_baud_rate() releases and re-acquires the port->lock, thus add lock annotation for Sparse static code checks. Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org> Link: https://lore.kernel.org/r/20230109152212.343476-1-krzysztof.kozlowski@linaro.org Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2023-01-19serial: sccnxp: Use devm_clk_get_enabled() helperChristophe JAILLET
The devm_clk_get_enabled() helper: - calls devm_clk_get() - calls clk_prepare_enable() and registers what is needed in order to call clk_disable_unprepare() when needed, as a managed resource. This simplifies the code. This also avoids some other warnings/issues. (see [1]) [1]: https://lore.kernel.org/all/20221118233101.never.215-kees@kernel.org/ Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr> Link: https://lore.kernel.org/r/735a807c2df835aa436dcbc76b374f983f89a9af.1672419577.git.christophe.jaillet@wanadoo.fr Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2023-01-19serial: ucc_uart: Add of_node_put() in ucc_uart_remove()Liang He
In ucc_uart_probe(), we have added proper of_node_put() in the failure paths. However, we miss it before we free *qe_port* in the remove() function. Signed-off-by: Liang He <windhl@126.com> Link: https://lore.kernel.org/r/20221205085437.1163682-1-windhl@126.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2023-01-19tty: serial: qcom-geni-serial: add support for serial engine DMABartosz Golaszewski
The qcom-geni-serial driver currently only works in SE FIFO mode. This limits the UART speed to around 180 kB/s. In order to achieve higher speeds we need to use SE DMA mode. Keep the console port working in FIFO mode but extend the code to use DMA for the high-speed port. Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org> Link: https://lore.kernel.org/r/20221229155030.418800-15-brgl@bgdev.pl Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2023-01-19tty: serial: qcom-geni-serial: use of_device_id dataBartosz Golaszewski
Instead of checking the device compatible in probe(), assign the device-specific data to struct of_device_id. We'll use it later when providing SE DMA support. Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org> Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org> Link: https://lore.kernel.org/r/20221229155030.418800-13-brgl@bgdev.pl Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2023-01-19tty: serial: qcom-geni-serial: drop the return value from handle_rxBartosz Golaszewski
The return value of the handle_rx() callback is never checked. Drop it. Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org> Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org> Link: https://lore.kernel.org/r/20221229155030.418800-12-brgl@bgdev.pl Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2023-01-19tty: serial: qcom-geni-serial: refactor qcom_geni_serial_send_chunk_fifo()Bartosz Golaszewski
Shuffle the code a bit, drop unneeded variables, make types of others more consistent and use uart_xmit_advance() instead of handling tail->xmit manually. Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org> Link: https://lore.kernel.org/r/20221229155030.418800-11-brgl@bgdev.pl Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2023-01-19tty: serial: qcom-geni-serial: split out the FIFO tx codeBartosz Golaszewski
qcom_geni_serial_handle_tx() is pretty big, let's move the code that handles the actual writing of data to a separate function which makes sense in preparation for introducing a dma variant of handle_tx(). Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org> Link: https://lore.kernel.org/r/20221229155030.418800-10-brgl@bgdev.pl Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2023-01-19tty: serial: qcom-geni-serial: remove unneeded tabsBartosz Golaszewski
Remove redundant indentation in struct member assignment. Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org> Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org> Link: https://lore.kernel.org/r/20221229155030.418800-9-brgl@bgdev.pl Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2023-01-19tty: serial: qcom-geni-serial: refactor qcom_geni_serial_isr()Bartosz Golaszewski
Simplify the conditions in qcom_geni_serial_isr() and fix indentation. Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org> Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org> Reviewed-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com> Link: https://lore.kernel.org/r/20221229155030.418800-8-brgl@bgdev.pl Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2023-01-19tty: serial: qcom-geni-serial: remove stray newlinesBartosz Golaszewski
Remove stray newlines around #ifdefs for consistency with the rest of the driver code. Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org> Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org> Link: https://lore.kernel.org/r/20221229155030.418800-7-brgl@bgdev.pl Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2023-01-19tty: serial: qcom-geni-serial: improve the to_dev_port() macroBartosz Golaszewski
The member we want to resolve in struct qcom_geni_serial_port is called uport so we don't need an additional redundant parameter in this macro. While at it: turn the macro into a static inline function. Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org> Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org> Link: https://lore.kernel.org/r/20221229155030.418800-6-brgl@bgdev.pl Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2023-01-19tty: serial: qcom-geni-serial: align #define valuesBartosz Golaszewski
Keep the #define symbols aligned for better readability. Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org> Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org> Link: https://lore.kernel.org/r/20221229155030.418800-5-brgl@bgdev.pl Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2023-01-19tty: serial: qcom-geni-serial: remove unused symbolsBartosz Golaszewski
Drop all unused symbols from the driver. Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org> Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org> Link: https://lore.kernel.org/r/20221229155030.418800-4-brgl@bgdev.pl Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2023-01-19tty: serial: qcom-geni-serial: drop unneeded forward definitionsBartosz Golaszewski
If we shuffle the code a bit, we can drop all forward definitions of various static functions. Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org> Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org> Link: https://lore.kernel.org/r/20221229155030.418800-3-brgl@bgdev.pl Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2023-01-19tty: serial: qcom-geni-serial: stop operations in progress at shutdownBartosz Golaszewski
We don't stop transmissions in progress at shutdown. This is fine with FIFO SE mode but with DMA (support for which we'll introduce later) it causes trouble so fix it now. Fixes: e83766334f96 ("tty: serial: qcom_geni_serial: No need to stop tx/rx on UART shutdown") Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org> Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org> Link: https://lore.kernel.org/r/20221229155030.418800-2-brgl@bgdev.pl Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2023-01-19tty: serial: fsl_lpuart: increase maximum uart_nr to eightNate Drude
Some SoCs like the i.MX93 have aliases for up to eight UARTs, see: https://github.com/torvalds/linux/blob/v6.1/arch/arm64/boot/dts/freescale/imx93.dtsi#L31-L38 Increase UART_NR from 6 to 8 to support lpuart7 and lpuart8 and avoid initialization failures like the following: [ 0.837146] fsl-lpuart 42690000.serial: serial6 out of range [ 0.842814] fsl-lpuart: probe of 42690000.serial failed with error -22 Signed-off-by: Nate Drude <nate.d@variscite.com> Reviewed-by: Sherry Sun <sherry.sun@nxp.com> Link: https://lore.kernel.org/r/20221222145634.2217793-1-nate.d@variscite.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2023-01-19tty: serial: imx: disable the break condition when shutdown the uart portSherry Sun
The comment in imx_uart_shutdown() says to disable the break condition, but it doesn't actually do that, here fix this by disabling UCR1_SNDBRK when closing the uart port like other uart drivers do. Signed-off-by: Sherry Sun <sherry.sun@nxp.com> Link: https://lore.kernel.org/r/20221214031137.28815-4-sherry.sun@nxp.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2023-01-19tty: serial: fsl_lpuart: disable the break condition when shutdown the uart portSherry Sun
Need to disable the break condition for lpuart driver when closing the uart port like other uart drivers do. Signed-off-by: Sherry Sun <sherry.sun@nxp.com> Link: https://lore.kernel.org/r/20221214031137.28815-3-sherry.sun@nxp.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2023-01-19tty: serial: fsl_lpuart: disable the CTS when send break signalSherry Sun
LPUART IP has a bug that it treats the CTS as higher priority than the break signal, which cause the break signal sending through UARTCTRL_SBK may impacted by the CTS input if the HW flow control is enabled. Add this workaround patch to fix the IP bug, we can disable CTS before asserting SBK to avoid any interference from CTS, and re-enable it when break off. Such as for the bluetooth chip power save feature, host can let the BT chip get into sleep state by sending a UART break signal, and wake it up by turning off the UART break. If the BT chip enters the sleep mode successfully, it will pull up the CTS line, if the BT chip is woken up, it will pull down the CTS line. If without this workaround patch, the UART TX pin cannot send the break signal successfully as it affected by the BT CTS pin. After adding this patch, the BT power save feature can work well. Signed-off-by: Sherry Sun <sherry.sun@nxp.com> Link: https://lore.kernel.org/r/20221214031137.28815-2-sherry.sun@nxp.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
generated by cgit v1.2.3 (git 2.39.1) at 2025-08-04 22:28:15 +0000