| Age | Commit message (Collapse) | Author |
|---|
|
We need the serial/tty fixes in here as well.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty into master
Pull tty/serial driver fixes from Greg KH:
:Here are some small tty and serial driver fixes for 5.8-rc6.
The largest set of patches in here is a revert of the sysrq changes
that went into 5.8-rc1 but turned out to cause a noticable overhead
and cpu usage.
Other than that, there's a few small serial driver fixes to resolve
reported issues, and finally resolving the spinlock init problem on
many serial driver consoles.
All of these have been in linux-next for a while with no reported
issues"
* tag 'tty-5.8-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty:
serial: core: Initialise spin lock before use in uart_configure_port()
serial: mxs-auart: add missed iounmap() in probe failure and remove
serial: sh-sci: Initialize spinlock for uart console
Revert "tty: xilinx_uartps: Fix missing id assignment to the console"
serial: core: drop redundant sysrq checks
serial: core: fix sysrq overhead regression
Revert "serial: core: Refactor uart_unlock_and_check_sysrq()"
tty/serial: fix serial_core.c kernel-doc warnings
tty: serial: cpm_uart: Fix behaviour for non existing GPIOs
|
|
When using the geni-serial as console, its important to be
able to hit the lowest possible power state in suspend,
even with no_console_suspend.
The only thing that prevents it today on platforms like the sc7180
is the interconnect BW votes, which we certainly don't need when
the system is in suspend. So in the suspend handler mark them as
ACTIVE_ONLY (0x3) and on resume switch them back to the ALWAYS tag (0x7)
Signed-off-by: Rajendra Nayak <rnayak@codeaurora.org>
Reviewed-by: Akash Asthana <akashast@codeaurora.org>
Tested-by: Matthias Kaehlcke <mka@chromium.org>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Link: https://lore.kernel.org/r/1594704709-26072-1-git-send-email-rnayak@codeaurora.org
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
|
|
The geni serial driver had a rule that we'd only use 1 byte per FIFO
word for the TX FIFO if we were being used for the serial console.
This is ugly and a bit of a pain. It's not too hard to fix, so fix
it.
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Reviewed-by: Evan Green <evgreen@chromium.org>
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Link: https://lore.kernel.org/r/20200626125844.2.Iabd56347670b9e4e916422773aba5b27943d19ee@changeid
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
|
|
The geni serial driver had the rather sketchy hack in it where it
would adjust the number of bytes per RX FIFO word from 4 down to 1 if
it detected that CONFIG_CONSOLE_POLL was enabled (for kgdb) and this
was a console port (defined by the kernel directing output to this
port via the "console=" command line argument).
The problem with that sketchy hack is that it's possible to run kgdb
over a serial port even if it isn't used for console.
Let's avoid the hack by simply handling the 4-bytes-per-FIFO word case
for kdb. We'll have to have a (very small) cache but that should be
fine.
A nice side effect of this patch is that an agetty (or similar)
running on this port is less likely to drop characters. We'll
have roughly 4 times the RX FIFO depth than we used to now.
NOTE: the character cache here isn't shared between the polling API
and the non-polling API. That means that, technically, the polling
API could eat a few extra bytes. This doesn't seem to pose a huge
problem in reality because we'll only get several characters per FIFO
word if those characters are all received at nearly the same time and
we don't really expect non-kgdb characters to be sent to the same port
as kgdb at the exact same time we're exiting kgdb.
ALSO NOTE: we still have the sketchy hack for setting the number of
bytes per TX FIFO word in place, but that one is less bad. kgdb
doesn't have any problem with this because it always just sends 1 byte
at a time and waits for it to finish. The TX FIFO hack is only really
needed for console output. In any case, a future patch will remove
that hack, too.
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Reviewed-by: Evan Green <evgreen@chromium.org>
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Link: https://lore.kernel.org/r/20200626125844.1.I8546ecb6c5beb054f70c5302d1a7293484212cd1@changeid
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
|
|
The comment near to uart_port_spin_lock_init() says:
Ensure that the serial console lock is initialised early.
If this port is a console, then the spinlock is already initialised.
and there is nothing about enabled or disabled consoles. The commit
a3cb39d258ef ("serial: core: Allow detach and attach serial device
for console") made a change, which follows the comment, and also to
prevent reinitialisation of the lock in use, when user detaches and
attaches back the same console device. But this change discovers
another issue, that uart_add_one_port() tries to access a spin lock
that now may be uninitialised. This happens when a driver expects
the serial core to register a console on its behalf. In this case
we must initialise a spin lock before use.
Fixes: a3cb39d258ef ("serial: core: Allow detach and attach serial device for console")
Reported-by: Marc Zyngier <maz@kernel.org>
Reported-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Reported-by: Guenter Roeck <linux@roeck-us.net>
Reported-by: Anatoly Pugachev <matorola@gmail.com>
Acked-by: Marc Zyngier <maz@kernel.org>
Tested-by: Tony Lindgren <tony@atomide.com>
Cc: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Tested-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Link: https://lore.kernel.org/r/20200706214903.56148-1-andriy.shevchenko@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
This driver calls ioremap() in probe, but it misses calling iounmap() in
probe's error handler and remove.
Add the missed calls to fix it.
Fixes: 47d37d6f94cc ("serial: Add auart driver for i.MX23/28")
Signed-off-by: Chuhong Yuan <hslester96@gmail.com>
Cc: stable <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20200709135608.68290-1-hslester96@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
serial core expects the spinlock to be initialized by the controller
driver for serial console, this patch makes sure the spinlock is
initialized, fixing the below issue:
[ 0.865928] BUG: spinlock bad magic on CPU#0, swapper/0/1
[ 0.865945] lock: sci_ports+0x0/0x4c80, .magic: 00000000, .owner: <none>/-1, .owner_cpu: 0
[ 0.865955] CPU: 0 PID: 1 Comm: swapper/0 Not tainted 5.8.0-rc1+ #112
[ 0.865961] Hardware name: HopeRun HiHope RZ/G2H with sub board (DT)
[ 0.865968] Call trace:
[ 0.865979] dump_backtrace+0x0/0x1d8
[ 0.865985] show_stack+0x14/0x20
[ 0.865996] dump_stack+0xe8/0x130
[ 0.866006] spin_dump+0x6c/0x88
[ 0.866012] do_raw_spin_lock+0xb0/0xf8
[ 0.866023] _raw_spin_lock_irqsave+0x80/0xa0
[ 0.866032] uart_add_one_port+0x3a4/0x4e0
[ 0.866039] sci_probe+0x504/0x7c8
[ 0.866048] platform_drv_probe+0x50/0xa0
[ 0.866059] really_probe+0xdc/0x330
[ 0.866066] driver_probe_device+0x58/0xb8
[ 0.866072] device_driver_attach+0x6c/0x90
[ 0.866078] __driver_attach+0x88/0xd0
[ 0.866085] bus_for_each_dev+0x74/0xc8
[ 0.866091] driver_attach+0x20/0x28
[ 0.866098] bus_add_driver+0x14c/0x1f8
[ 0.866104] driver_register+0x60/0x110
[ 0.866109] __platform_driver_register+0x40/0x48
[ 0.866119] sci_init+0x2c/0x34
[ 0.866127] do_one_initcall+0x88/0x428
[ 0.866137] kernel_init_freeable+0x2c0/0x328
[ 0.866143] kernel_init+0x10/0x108
[ 0.866150] ret_from_fork+0x10/0x18
Signed-off-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Reviewed-by: Biju Das <biju.das.jz@bp.renesas.com>
Fixes: a3cb39d258ef ("serial: core: Allow detach and attach serial device for console")
Cc: stable <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/1593618100-2151-1-git-send-email-prabhakar.mahadev-lad.rj@bp.renesas.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Add support of generic DT binding for annoucing RTS/CTS lines. The initial
binding 'st,hw-flow-control' is not needed anymore since generic binding
is available, but is kept for backward compatibility.
Signed-off-by: Erwan Le Ray <erwan.leray@st.com>
Link: https://lore.kernel.org/r/20200520133932.30441-3-erwan.leray@st.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
This reverts commit 2ae11c46d5fdc46cb396e35911c713d271056d35.
It turned out to break the ultra96-rev1, e.g., which uses uart1 as
serial0 (and stdout-path = "serial0:115200n8").
Fixes: 2ae11c46d5fd ("tty: xilinx_uartps: Fix missing id assignment to the console")
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Jan Kiszka <jan.kiszka@siemens.com>
Reviewed-by: Michal Simek <michal.simek@xilinx.com>
Tested-by: Michal Simek <michal.simek@xilinx.com>
Link: https://lore.kernel.org/r/f4092727-d8f5-5f91-2c9f-76643aace993@siemens.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Commit 8e20fc391711 ("serial_core: Move sysrq functions from header
file") converted the inline sysrq helpers to exported functions which
are now called for every received character, interrupt and break signal
also on systems without CONFIG_MAGIC_SYSRQ_SERIAL instead of being
optimised away by the compiler.
Inlining these helpers again also avoids the function call overhead when
CONFIG_MAGIC_SYSRQ_SERIAL is enabled (e.g. when the port is not used as
a console).
Fixes: 8e20fc391711 ("serial_core: Move sysrq functions from header file")
Cc: Dmitry Safonov <0x7f454c46@gmail.com>
Signed-off-by: Johan Hovold <johan@kernel.org>
Cc: stable <stable@vger.kernel.org>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Dmitry Safonov <0x7f454c46@gmail.com>
Link: https://lore.kernel.org/r/20200610152232.16925-3-johan@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
This reverts commit da9a5aa3402db0ff3b57216d8dbf2478e1046cae.
In order to ease backporting a fix for a sysrq regression, revert this
rewrite which was since added on top.
The other sysrq helpers now bail out early when sysrq is not enabled;
it's better to keep that pattern here as well.
Note that the __releases() attribute won't be needed after the follow-on
fix either.
Fixes: da9a5aa3402d ("serial: core: Refactor uart_unlock_and_check_sysrq()")
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20200610152232.16925-2-johan@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
platform_get_irq() provides an established error code and error message.
Also, it's better to use dedicated API to retrieve Linux IRQ resource.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Matthias Brugger <matthias.bgg@gmail.com>
Link: https://lore.kernel.org/r/20200618122952.88265-1-andriy.shevchenko@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
platform_get_irq() provides an established error code and error message.
Also, it's better to use dedicated API to retrieve Linux IRQ resource.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20200618123320.88612-1-andriy.shevchenko@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
platform_get_irq() provides an established error code and error message.
Also, it's better to use dedicated API to retrieve Linux IRQ resource.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20200618122744.88204-1-andriy.shevchenko@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
platform_get_irq() provides an established error code and error message.
Also, it's better to use dedicated API to retrieve Linux IRQ resource.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20200618122024.87170-1-andriy.shevchenko@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
platform_get_irq() provides an established error code and error message.
Also, it's better to use dedicated API to retrieve Linux IRQ resource.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20200618095144.73852-1-andriy.shevchenko@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
In commit a4912303ac6f ("serial: kgdboc: Allow earlycon initialization
to be deferred") it looks like Daniel really took Linus's new
suggestion about not needing to wrap at 80 columns to heart and he
jammed two full lines of comments into one line. Either that or he
just somehow accidentally deleted a carriage return when doing final
edits on the patch. In either case let's make it look prettier.
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Link: https://lore.kernel.org/r/20200602124044.1.Iee31247bc080d42a02e167454b1225a1b4283705@changeid
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Since dev_err() calls can lead to synchronous writes to another serial
console these calls can provide significant latency during irq-handling
in tegra_uart_isr(). With this latency another interrupt is likely to
apper during handling of the first interrupt, which might lock up the
kernel completely.
These errors are reported to the error counters so converting the
dev_err() to dev_dbg() is appropriate.
Signed-off-by: Randolph Maaßen <gaireg@gaireg.de>
Link: https://lore.kernel.org/r/20200605145714.9964-1-gaireg@gaireg.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
get_num_ports returns -ENODEV, and the result is stored in int, so it
should not be unsigned. Zero ports does not seem to make sense, so
make that check consistent.
Signed-off-by: Pavel Machek (CIP) <pavel@denx.de>
Link: https://lore.kernel.org/r/20200606151146.GA10940@amd
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Drop the recently added gpio include from the serial-core header in
favour of a forward declaration and instead include the gpio header only
where needed.
Signed-off-by: Johan Hovold <johan@kernel.org>
Link: https://lore.kernel.org/r/20200610155121.14014-1-johan@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Fix kernel-doc warnings in serial_core.c:
../drivers/tty/serial/serial_core.c:3300: warning: Function parameter or member 'port' not described in 'uart_get_rs485_mode'
../drivers/tty/serial/serial_core.c:3300: warning: Excess function parameter 'dev' description in 'uart_get_rs485_mode'
../drivers/tty/serial/serial_core.c:3300: warning: Excess function parameter 'rs485conf' description in 'uart_get_rs485_mode'
Fixes: c150c0f362c1 ("serial: Allow uart_get_rs485_mode() to return errno")
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Cc: Lukas Wunner <lukas@wunner.de>
Cc: Heiko Stuebner <heiko@sntech.de>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: linux-serial@vger.kernel.org
Link: https://lore.kernel.org/r/e170db8e-5c8b-27ac-79a4-81b96ac0ca2d@infradead.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
The formula for the baud rate is
baud rate = "baud clock / ((OSR+1) × SBR)
Algorithm used in function lpuart32_serial_setbrg() only changes
the SBR. Even with maxmum value put in, OSR stays at 0x7 and the
lowest baud rate would be ~ 2600 bps
Update the algorithm to allow driver operation at 1200,2400 or 600 bps
Signed-off-by: Vabhav Sharma <vabhav.sharma@nxp.com>
Link: https://lore.kernel.org/r/1593170434-13524-1-git-send-email-vabhav.sharma@oss.nxp.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
The ARRAY_SIZE() is the number of elements but we want the number of
bytes so sizeof() is more appropriate. Fortunately, it's the same
thing here because this is an array of u8 so this doesn't change
runtime.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Link: https://lore.kernel.org/r/20200624132744.GD9972@mwanda
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
devm_gpiod_get_index() doesn't return NULL but -ENOENT when the
requested GPIO doesn't exist, leading to the following messages:
[ 2.742468] gpiod_direction_input: invalid GPIO (errorpointer)
[ 2.748147] can't set direction for gpio #2: -2
[ 2.753081] gpiod_direction_input: invalid GPIO (errorpointer)
[ 2.758724] can't set direction for gpio #3: -2
[ 2.763666] gpiod_direction_output: invalid GPIO (errorpointer)
[ 2.769394] can't set direction for gpio #4: -2
[ 2.774341] gpiod_direction_input: invalid GPIO (errorpointer)
[ 2.779981] can't set direction for gpio #5: -2
[ 2.784545] ff000a20.serial: ttyCPM1 at MMIO 0xfff00a20 (irq = 39, base_baud = 8250000) is a CPM UART
Use devm_gpiod_get_index_optional() instead.
At the same time, handle the error case and properly exit
with an error.
Fixes: 97cbaf2c829b ("tty: serial: cpm_uart: Convert to use GPIO descriptors")
Cc: stable@vger.kernel.org
Cc: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Christophe Leroy <christophe.leroy@csgroup.eu>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Link: https://lore.kernel.org/r/694a25fdce548c5ee8b060ef6a4b02746b8f25c0.1591986307.git.christophe.leroy@csgroup.eu
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
There is a spelling mistake in a comment. Fix it.
Signed-off-by: Tamseel Shams <m.shams@samsung.com>
Reviewed-by: Alim Akhtar <alim.akhtar@samsung.com>
Link: https://lore.kernel.org/r/20200617105907.7143-1-m.shams@samsung.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Make the code slightly more readable by removing unneeded line breaks,
adding missing line breaks and white spaces. This also fixes few strict
checkpatch suggestions:
CHECK: spaces preferred around that '-' (ctx:VxV)
CHECK: Unbalanced braces around else statement
CHECK: Lines should not end with a '('
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Link: https://lore.kernel.org/r/20200617152856.18086-1-krzk@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
In kgdb context, calling console handlers aren't safe due to locks used
in those handlers which could in turn lead to a deadlock. Although, using
oops_in_progress increases the chance to bypass locks in most console
handlers but it might not be sufficient enough in case a console uses
more locks (VT/TTY is good example).
Currently when a driver provides both polling I/O and a console then kdb
will output using the console. We can increase robustness by using the
currently active polling I/O driver (which should be lockless) instead
of the corresponding console. For several common cases (e.g. an
embedded system with a single serial port that is used both for console
output and debugger I/O) this will result in no console handler being
used.
In order to achieve this we need to reverse the order of preference to
use dbg_io_ops (uses polling I/O mode) over console APIs. So we just
store "struct console" that represents debugger I/O in dbg_io_ops and
while emitting kdb messages, skip console that matches dbg_io_ops
console in order to avoid duplicate messages. After this change,
"is_console" param becomes redundant and hence removed.
Suggested-by: Daniel Thompson <daniel.thompson@linaro.org>
Signed-off-by: Sumit Garg <sumit.garg@linaro.org>
Link: https://lore.kernel.org/r/1591264879-25920-5-git-send-email-sumit.garg@linaro.org
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Reviewed-by: Petr Mladek <pmladek@suse.com>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Daniel Thompson <daniel.thompson@linaro.org>
|
|
For unifying console ->setup() handling, which is poorly documented,
return error code, rather than non-zero arbitrary number.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Petr Mladek <pmladek@suse.com>
Acked-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Petr Mladek <pmladek@suse.com>
Link: https://lore.kernel.org/r/20200618164751.56828-4-andriy.shevchenko@linux.intel.com
|
|
For unifying console ->setup() handling, which is poorly documented,
return error code, rather than non-zero arbitrary number.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Petr Mladek <pmladek@suse.com>
Acked-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Petr Mladek <pmladek@suse.com>
Link: https://lore.kernel.org/r/20200618164751.56828-3-andriy.shevchenko@linux.intel.com
|
|
geni serial needs to express a perforamnce state requirement on CX
powerdomain depending on the frequency of the clock rates.
Use OPP table from DT to register with OPP framework and use
dev_pm_opp_set_rate() to set the clk/perf state.
Signed-off-by: Rajendra Nayak <rnayak@codeaurora.org>
Reviewed-by: Matthias Kaehlcke <mka@chromium.org>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Akash Asthana <akashast@codeaurora.org>
Cc: linux-serial@vger.kernel.org
Link: https://lore.kernel.org/r/1592222564-13556-2-git-send-email-rnayak@codeaurora.org
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
|
|
Get the interconnect paths for Uart based Serial Engine device
and vote according to the baud rate requirement of the driver.
Signed-off-by: Akash Asthana <akashast@codeaurora.org>
Reviewed-by: Matthias Kaehlcke <mka@chromium.org>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Link: https://lore.kernel.org/r/1592908737-7068-5-git-send-email-akashast@codeaurora.org
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
|
|
QUP core clock is shared among all the SE drivers present on particular
QUP wrapper, the system will reset(unclocked access) if earlycon used after
QUP core clock is put to 0 from other SE drivers before real console comes
up.
As earlycon can't vote for it's QUP core need, to fix this add ICC
support to common/QUP wrapper driver and put vote for QUP core from
probe on behalf of earlycon and remove vote during earlycon exit call.
Signed-off-by: Akash Asthana <akashast@codeaurora.org>
Reported-by: Matthias Kaehlcke <mka@chromium.org>
Reviewed-by: Matthias Kaehlcke <mka@chromium.org>
Link: https://lore.kernel.org/r/1592908737-7068-3-git-send-email-akashast@codeaurora.org
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
|
|
Because SCHED_FIFO is a broken scheduler model (see previous patches)
take away the priority field, the kernel can't possibly make an
informed decision.
Effectively no change.
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Reviewed-by: Ingo Molnar <mingo@kernel.org>
|
|
Since commit 84af7a6194e4 ("checkpatch: kconfig: prefer 'help' over
'---help---'"), the number of '---help---' has been gradually
decreasing, but there are still more than 2400 instances.
This commit finishes the conversion. While I touched the lines,
I also fixed the indentation.
There are a variety of indentation styles found.
a) 4 spaces + '---help---'
b) 7 spaces + '---help---'
c) 8 spaces + '---help---'
d) 1 space + 1 tab + '---help---'
e) 1 tab + '---help---' (correct indentation)
f) 1 tab + 1 space + '---help---'
g) 1 tab + 2 spaces + '---help---'
In order to convert all of them to 1 tab + 'help', I ran the
following commend:
$ find . -name 'Kconfig*' | xargs sed -i 's/^[[:space:]]*---help---/\thelp/'
Signed-off-by: Masahiro Yamada <masahiroy@kernel.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty
Pull tty/serial driver updates from Greg KH:
"Here is the tty and serial driver updates for 5.8-rc1
Nothing huge at all, just a lot of little serial driver fixes, updates
for new devices and features, and other small things. Full details are
in the shortlog.
All of these have been in linux-next with no issues for a while"
* tag 'tty-5.8-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty: (67 commits)
tty: serial: qcom_geni_serial: Add 51.2MHz frequency support
tty: serial: imx: clear Ageing Timer Interrupt in handler
serial: 8250_fintek: Add F81966 Support
sc16is7xx: Add flag to activate IrDA mode
dt-bindings: sc16is7xx: Add flag to activate IrDA mode
serial: 8250: Support rs485 bus termination GPIO
serial: 8520_port: Fix function param documentation
dt-bindings: serial: Add binding for rs485 bus termination GPIO
vt: keyboard: avoid signed integer overflow in k_ascii
serial: 8250: Enable 16550A variants by default on non-x86
tty: hvc_console, fix crashes on parallel open/close
serial: imx: Initialize lock for non-registered console
sc16is7xx: Read the LSR register for basic device presence check
sc16is7xx: Allow sharing the IRQ line
sc16is7xx: Use threaded IRQ
sc16is7xx: Always use falling edge IRQ
tty: n_gsm: Fix bogus i++ in gsm_data_kick
tty: n_gsm: Remove unnecessary test in gsm_print_packet()
serial: stm32: add no_console_suspend support
tty: serial: fsl_lpuart: Use __maybe_unused instead of #if CONFIG_PM_SLEEP
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci
Pull PCI updates from Bjorn Helgaas:
"Enumeration:
- Program MPS for RCiEP devices (Ashok Raj)
- Fix pci_register_host_bridge() device_register() error handling
(Rob Herring)
- Fix pci_host_bridge struct device release/free handling (Rob
Herring)
Resource management:
- Allow resizing BARs for devices on root bus (Ard Biesheuvel)
Power management:
- Reduce Thunderbolt resume time by working around devices that don't
support DLL Link Active reporting (Mika Westerberg)
- Work around a Pericom USB controller OHCI/EHCI PME# defect
(Kai-Heng Feng)
Virtualization:
- Add ACS quirk for Intel Root Complex Integrated Endpoints (Ashok
Raj)
- Avoid FLR for AMD Starship USB 3.0 (Kevin Buettner)
- Avoid FLR for AMD Matisse HD Audio & USB 3.0 (Marcos Scriven)
Error handling:
- Use only _OSC (not HEST FIRMWARE_FIRST) to determine AER ownership
(Alexandru Gagniuc, Kuppuswamy Sathyanarayanan)
- Reduce verbosity by logging only ACPI_NOTIFY_DISCONNECT_RECOVER
events (Kuppuswamy Sathyanarayanan)
- Don't enable AER by default in Kconfig (Bjorn Helgaas)
Peer-to-peer DMA:
- Add AMD Zen Raven and Renoir Root Ports to whitelist (Alex Deucher)
ASPM:
- Allow ASPM on links to PCIe-to-PCI/PCI-X Bridges (Kai-Heng Feng)
Endpoint framework:
- Fix DMA channel release in test (Kunihiko Hayashi)
- Add page size as argument to pci_epc_mem_init() (Lad Prabhakar)
- Add support to handle multiple base for mapping outbound memory
(Lad Prabhakar)
Generic host bridge driver:
- Support building as module (Rob Herring)
- Eliminate pci_host_common_probe wrappers (Rob Herring)
Amlogic Meson PCIe controller driver:
- Don't use FAST_LINK_MODE to set up link (Marc Zyngier)
Broadcom STB PCIe controller driver:
- Disable ASPM L0s if 'aspm-no-l0s' in DT (Jim Quinlan)
- Fix clk_put() error (Jim Quinlan)
- Fix window register offset (Jim Quinlan)
- Assert fundamental reset on initialization (Nicolas Saenz Julienne)
- Add notify xHCI reset property (Nicolas Saenz Julienne)
- Add init routine for Raspberry Pi 4 VL805 USB controller (Nicolas
Saenz Julienne)
- Sync with Raspberry Pi 4 firmware for VL805 initialization (Nicolas
Saenz Julienne)
Cadence PCIe controller driver:
- Remove "cdns,max-outbound-regions" DT property (replaced by
"ranges") (Kishon Vijay Abraham I)
- Read 32-bit (not 16-bit) Vendor ID/Device ID property from DT
(Kishon Vijay Abraham I)
Marvell Aardvark PCIe controller driver:
- Improve link training (Marek Behún)
- Add PHY support (Marek Behún)
- Add "phys", "max-link-speed", "reset-gpios" to dt-binding (Marek
Behún)
- Train link immediately after enabling training to work around
detection issues with some cards (Pali Rohár)
- Issue PERST via GPIO to work around detection issues (Pali Rohár)
- Don't blindly enable ASPM L0s (Pali Rohár)
- Replace custom macros by standard linux/pci_regs.h macros (Pali
Rohár)
Microsoft Hyper-V host bridge driver:
- Fix probe failure path to release resource (Wei Hu)
- Retry PCI bus D0 entry on invalid device state for kdump (Wei Hu)
Renesas R-Car PCIe controller driver:
- Fix incorrect programming of OB windows (Andrew Murray)
- Add suspend/resume (Kazufumi Ikeda)
- Rename pcie-rcar.c to pcie-rcar-host.c (Lad Prabhakar)
- Add endpoint controller driver (Lad Prabhakar)
- Fix PCIEPAMR mask calculation (Lad Prabhakar)
- Add r8a77961 to DT binding (Yoshihiro Shimoda)
Socionext UniPhier Pro5 controller driver:
- Add endpoint controller driver (Kunihiko Hayashi)
Synopsys DesignWare PCIe controller driver:
- Program outbound ATU upper limit register (Alan Mikhak)
- Fix inner MSI IRQ domain registration (Marc Zyngier)
Miscellaneous:
- Check for platform_get_irq() failure consistently (negative return
means failure) (Aman Sharma)
- Fix several runtime PM get/put imbalances (Dinghao Liu)
- Use flexible-array and struct_size() helpers for code cleanup
(Gustavo A. R. Silva)
- Update & fix issues in bridge emulation of PCIe registers (Jon
Derrick)
- Add macros for bridge window names (PCI_BRIDGE_IO_WINDOW, etc)
(Krzysztof Wilczyński)
- Work around Intel PCH MROMs that have invalid BARs (Xiaochun Lee)"
* tag 'pci-v5.8-changes' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci: (100 commits)
PCI: uniphier: Add Socionext UniPhier Pro5 PCIe endpoint controller driver
PCI: Add ACS quirk for Intel Root Complex Integrated Endpoints
PCI/DPC: Print IRQ number used by port
PCI/AER: Use "aer" variable for capability offset
PCI/AER: Remove redundant dev->aer_cap checks
PCI/AER: Remove redundant pci_is_pcie() checks
PCI/AER: Remove HEST/FIRMWARE_FIRST parsing for AER ownership
PCI: tegra: Fix runtime PM imbalance on error
PCI: vmd: Filter resource type bits from shadow register
PCI: tegra194: Fix runtime PM imbalance on error
dt-bindings: PCI: Add UniPhier PCIe endpoint controller description
PCI: hv: Use struct_size() helper
PCI: Rename _DSM constants to align with spec
PCI: Avoid FLR for AMD Starship USB 3.0
PCI: Avoid FLR for AMD Matisse HD Audio & USB 3.0
x86/PCI: Drop unused xen_register_pirq() gsi_override parameter
PCI: dwc: Use private data pointer of "struct irq_domain" to get pcie_port
PCI: amlogic: meson: Don't use FAST_LINK_MODE to set up link
PCI: dwc: Fix inner MSI IRQ domain registration
PCI: dwc: pci-dra7xx: Use devm_platform_ioremap_resource_byname()
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/danielt/linux
Pull kgdb updates from Daniel Thompson:
"By far the biggest change in this cycle are the changes that allow
much earlier debug of systems that are hooked up via UART by taking
advantage of the earlycon framework to implement the kgdb I/O hooks
before handing over to the regular polling I/O drivers once they are
available. When discussing Doug's work we also found and fixed an
broken raw_smp_processor_id() sequence in in_dbg_master().
Also included are a collection of much smaller fixes and tweaks: a
couple of tweaks to ged rid of doc gen or coccicheck warnings, future
proof some internal calculations that made implicit power-of-2
assumptions and eliminate some rather weird handling of magic
environment variables in kdb"
* tag 'kgdb-5.8-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/danielt/linux:
kdb: Remove the misfeature 'KDBFLAGS'
kdb: Cleanup math with KDB_CMD_HISTORY_COUNT
serial: amba-pl011: Support kgdboc_earlycon
serial: 8250_early: Support kgdboc_earlycon
serial: qcom_geni_serial: Support kgdboc_earlycon
serial: kgdboc: Allow earlycon initialization to be deferred
Documentation: kgdboc: Document new kgdboc_earlycon parameter
kgdb: Don't call the deinit under spinlock
kgdboc: Disable all the early code when kgdboc is a module
kgdboc: Add kgdboc_earlycon to support early kgdb using boot consoles
kgdboc: Remove useless #ifdef CONFIG_KGDB_SERIAL_CONSOLE in kgdboc
kgdb: Prevent infinite recursive entries to the debugger
kgdb: Delay "kgdbwait" to dbg_late_init() by default
kgdboc: Use a platform device to handle tty drivers showing up late
Revert "kgdboc: disable the console lock when in kgdb"
kgdb: Disable WARN_CONSOLE_UNLOCKED for all kgdb
kgdb: Return true in kgdb_nmi_poll_knock()
kgdb: Drop malformed kernel doc comment
kgdb: Fix spurious true from in_dbg_master()
|
|
Implement the read() function in the early console driver. With
recently added kgdboc_earlycon feature, this allows you to use kgdb
to debug fairly early into the system boot.
We only bother implementing this if polling is enabled since kgdb can't
be enabled without that.
Signed-off-by: Sumit Garg <sumit.garg@linaro.org>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Reviewed-by: Daniel Thompson <daniel.thompson@linaro.org>
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Link: https://lore.kernel.org/r/20200507130644.v4.12.I8ee0811f0e0816dd8bfe7f2f5540b3dba074fae8@changeid
Signed-off-by: Daniel Thompson <daniel.thompson@linaro.org>
|
|
Implement the read() function in the early console driver. With
recent kgdb patches this allows you to use kgdb to debug fairly early
into the system boot.
We only bother implementing this if polling is enabled since kgdb
can't be enabled without that.
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Reviewed-by: Daniel Thompson <daniel.thompson@linaro.org>
Link: https://lore.kernel.org/r/20200507130644.v4.11.I8f668556c244776523320a95b09373a86eda11b7@changeid
Signed-off-by: Daniel Thompson <daniel.thompson@linaro.org>
|
|
Implement the read() function in the early console driver. With
recent kgdb patches this allows you to use kgdb to debug fairly early
into the system boot.
We only bother implementing this if polling is enabled since kgdb
can't be enabled without that.
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Link: https://lore.kernel.org/r/20200507130644.v4.10.If2deff9679a62c1ce1b8f2558a8635dc837adf8c@changeid
Signed-off-by: Daniel Thompson <daniel.thompson@linaro.org>
|
|
Currently there is no guarantee that an earlycon will be initialized
before kgdboc tries to adopt it. Almost the opposite: on systems
with ACPI then if earlycon has no arguments then it is guaranteed that
earlycon will not be initialized.
This patch mitigates the problem by giving kgdboc_earlycon a second
chance during console_init(). This isn't quite as good as stopping during
early parameter parsing but it is still early in the kernel boot.
Signed-off-by: Daniel Thompson <daniel.thompson@linaro.org>
Link: https://lore.kernel.org/r/20200430161741.1832050-1-daniel.thompson@linaro.org
Reviewed-by: Douglas Anderson <dianders@chromium.org>
|
|
When kgdboc is compiled as a module all of the "ekgdboc" and
"kgdb_earlycon" code isn't useful and, in fact, breaks compilation.
This is because early_param() isn't defined for modules and that's how
this code gets configured.
It turns out that this was broken by commit eae3e19ca930 ("kgdboc:
Remove useless #ifdef CONFIG_KGDB_SERIAL_CONSOLE in kgdboc") and then
made worse by commit 220995622da5 ("kgdboc: Add kgdboc_earlycon to
support early kgdb using boot consoles"). I guess the #ifdef wasn't
so useless, even if it wasn't obvious why it was useful. When kgdboc
was compiled as a module only "CONFIG_KGDB_SERIAL_CONSOLE_MODULE" was
defined, not "CONFIG_KGDB_SERIAL_CONSOLE". That meant that the old
module.
Let's basically do the same thing that the old code (pre-removal of
the #ifdef) did but use "IS_BUILTIN(CONFIG_KGDB_SERIAL_CONSOLE)" to
make it more obvious what the point of the check is. We'll fix
kgdboc_earlycon in a similar way.
Fixes: 220995622da5 ("kgdboc: Add kgdboc_earlycon to support early kgdb using boot consoles")
Fixes: eae3e19ca930 ("kgdboc: Remove useless #ifdef CONFIG_KGDB_SERIAL_CONSOLE in kgdboc")
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Link: https://lore.kernel.org/r/20200519084345.1.I91670accc8a5ddabab227eb63bb4ad3e2e9d2b58@changeid
Signed-off-by: Daniel Thompson <daniel.thompson@linaro.org>
|
|
To support BT use case over UART at baud rate of 3.2 Mbps,
we need SE clocks to run at 51.2MHz frequency. Previously this
frequency was not available in clk src, so, we were requesting
for 102.4 MHz and dividing it internally by 2 to get 51.2MHz.
As now 51.2MHz frequency is made available in clk src,
adding this frequency to UART frequency table.
We will save significant amount of power, if 51.2 is used
because it belongs to LowSVS range whereas 102.4 fall into
Nominal category.
Signed-off-by: satya priya <skakit@codeaurora.org>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Link: https://lore.kernel.org/r/1590747282-5487-1-git-send-email-skakit@codeaurora.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
The AGTIM flag must be cleared explicitly, otherwise the IRQ handler
will be called in an endless loop.
Fortunately, this issue currently doesn't affect mainline kernels in
practice, as the the RX FIFO trigger level is set to 1 in UFCR. When
setting the trigger level to a higher number, the issue is trivially
reproducible by any RX without DMA that doesn't fill the FIFO up to the
configured level.
Signed-off-by: Matthias Schiffer <matthias.schiffer@ew.tq-group.com>
Link: https://lore.kernel.org/r/20200528154747.14201-1-matthias.schiffer@ew.tq-group.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Fintek F81966 is a LPC/eSPI to 6 UARTs SuperIO. It has fully compatible
with F81866. It's also need check the IRQ mode with system assigned.
F81966 IRQ Mode setting:
0xf0
Bit1: IRQ_MODE0
Bit0: Share mode (always on)
0xf6
Bit3: IRQ_MODE1
Level/Low: IRQ_MODE0:0, IRQ_MODE1:0
Edge/High: IRQ_MODE0:1, IRQ_MODE1:0
Signed-off-by: Ji-Ze Hong (Peter Hong) <hpeter+linux_kernel@gmail.com>
Cc: Ji-Ze Hong (Peter Hong) <peter_hong@fintek.com.tw>
Link: https://lore.kernel.org/r/20200528022429.32078-1-hpeter+linux_kernel@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
This series of uart controllers is able to work in IrDA mode.
Add per-port flag to the device-tree to enable that feature if needed.
Signed-off-by: Pascal Huerst <pascal.huerst@gmail.com>
Signed-off-by: Daniel Mack <daniel@zonque.org>
Link: https://lore.kernel.org/r/20200529055058.1606910-3-daniel@zonque.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Commit e8759ad17d41 ("serial: uapi: Add support for bus termination")
introduced the ability to enable rs485 bus termination from user space.
So far the feature is only used by a single driver, 8250_exar.c, using a
hardcoded GPIO pin specific to Siemens IOT2040 products.
Provide for a more generic solution by allowing specification of an
rs485 bus termination GPIO pin in the device tree: Amend the serial
core to retrieve the GPIO from the device tree (or ACPI table) and amend
the default ->rs485_config() callback for 8250 drivers to change the
GPIO on request from user space.
Perhaps 8250_exar.c can be converted to the generic approach in a
follow-up patch.
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Cc: Jan Kiszka <jan.kiszka@siemens.com>
Link: https://lore.kernel.org/r/94c6c800d1ca9fa04766dd1d43a8272c5ad4bedd.1589811297.git.lukas@wunner.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
The parameter is named p while the documentation talks about up.
Fix the doc to be in line with the code.
Fixes: 058bc104f7ca ("serial: 8250: Generalize rs485 software emulation")
Suggested-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: Heiko Stuebner <heiko.stuebner@theobroma-systems.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20200517215610.2131618-2-heiko@sntech.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Some embedded devices still use these serial ports; make sure they're
still enabled by default on architectures more likely to have them, to
avoid rendering someone's console unavailable.
Reported-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reported-by: Maxim Kochetkov <fido_max@inbox.ru>
Fixes: dc56ecb81a0a ("serial: 8250: Support disabling mdelay-filled probes of 16550A variants")
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Josh Triplett <josh@joshtriplett.org>
Link: https://lore.kernel.org/r/a20b5fb7dd295cfb48160eecf4bdebd76332d67d.1590509426.git.josh@joshtriplett.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
