Age | Commit message (Collapse) | Author |
|
For lpuart32 platforms, UARTMODIR register is used instead of UARTMODEM.
So here should configure the corresponding UARTMODIR register bits to
avoid confusion.
Reviewed-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Signed-off-by: Sherry Sun <sherry.sun@nxp.com>
Link: https://lore.kernel.org/r/20230414022111.20896-1-sherry.sun@nxp.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Based on the fls function definition provided below, we should not
subtract 1 to obtain the correct buffer length:
fls(0) = 0, fls(1) = 1, fls(0x80000000) = 32.
Fixes: 5887ad43ee02 ("tty: serial: fsl_lpuart: Use cyclic DMA for Rx")
Signed-off-by: Shenwei Wang <shenwei.wang@nxp.com>
Link: https://lore.kernel.org/r/20230410195555.1003900-1-shenwei.wang@nxp.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
For serdev framework, tty->dev is a NULL pointer, lpuart_uport_is_active
calling device_may_wakeup() may cause kernel NULL pointer crash, so here
add the NULL pointer check before using it.
Fixes: 4f5cb8c5e915 ("tty: serial: fsl_lpuart: enable wakeup source for lpuart")
Cc: stable <stable@kernel.org>
Signed-off-by: Sherry Sun <sherry.sun@nxp.com>
Link: https://lore.kernel.org/r/20230323110923.24581-1-sherry.sun@nxp.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
UARTCTRL_SBK is asserted in lpuart32_tx_empty
According to LPUART RM, Transmission Complete Flag becomes 0 if queuing
a break character by writing 1 to CTRL[SBK], so here need to avoid
checking for transmission complete when UARTCTRL_SBK is asserted,
otherwise the lpuart32_tx_empty may never get TIOCSER_TEMT.
Commit 2411fd94ceaa("tty: serial: fsl_lpuart: skip waiting for
transmission complete when UARTCTRL_SBK is asserted") only fix it in
lpuart32_set_termios(), here also fix it in lpuart32_tx_empty().
Fixes: 380c966c093e ("tty: serial: fsl_lpuart: add 32-bit register interface support")
Cc: stable <stable@kernel.org>
Signed-off-by: Sherry Sun <sherry.sun@nxp.com>
Link: https://lore.kernel.org/r/20230323054415.20363-1-sherry.sun@nxp.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
From time to time DMA completion can come in the middle of DMA shutdown:
<process ctx>: <IRQ>:
lpuart32_shutdown()
lpuart_dma_shutdown()
del_timer_sync()
lpuart_dma_rx_complete()
lpuart_copy_rx_to_tty()
mod_timer()
lpuart_dma_rx_free()
When the timer fires a bit later, sport->dma_rx_desc is NULL:
Unable to handle kernel NULL pointer dereference at virtual address 0000000000000004
pc : lpuart_copy_rx_to_tty+0xcc/0x5bc
lr : lpuart_timer_func+0x1c/0x2c
Call trace:
lpuart_copy_rx_to_tty
lpuart_timer_func
call_timer_fn
__run_timers.part.0
run_timer_softirq
__do_softirq
__irq_exit_rcu
irq_exit
handle_domain_irq
gic_handle_irq
call_on_irq_stack
do_interrupt_handler
...
To fix this fold del_timer_sync() into lpuart_dma_rx_free() after
dmaengine_terminate_sync() to make sure timer will not be re-started in
lpuart_copy_rx_to_tty() <= lpuart_dma_rx_complete().
Fixes: 4a8588a1cf86 ("serial: fsl_lpuart: delete timer on shutdown")
Cc: stable <stable@kernel.org>
Signed-off-by: Alexander Sverdlin <alexander.sverdlin@siemens.com>
Link: https://lore.kernel.org/r/20230309134302.74940-2-alexander.sverdlin@siemens.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
UARTCTRL_SBK is asserted
According to LPUART RM, Transmission Complete Flag becomes 0 if queuing
a break character by writing 1 to CTRL[SBK], so here need to skip
waiting for transmission complete when UARTCTRL_SBK is asserted,
otherwise the kernel may stuck here.
And actually set_termios() adds transmission completion waiting to avoid
data loss or data breakage when changing the baud rate, but we don't
need to worry about this when queuing break characters.
Signed-off-by: Sherry Sun <sherry.sun@nxp.com>
Cc: stable <stable@kernel.org>
Link: https://lore.kernel.org/r/20230223093941.31790-1-sherry.sun@nxp.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
The previous 'commit 846651eca073 ("serial: fsl_lpuart: RS485 RTS
polariy is inverse")' only fixed the inverse issue on lpuart 8bit
platforms.
This is a follow-up patch to fix the RS485 polarity inverse
issue on lpuart 32bit platforms.
Fixes: 03895cf41d18 ("tty: serial: fsl_lpuart: Add support for RS-485")
Reported-by: Sherry Sun <sherry.sun@nxp.com>
Signed-off-by: Shenwei Wang <shenwei.wang@nxp.com>
Link: https://lore.kernel.org/r/20230207162420.3647904-1-shenwei.wang@nxp.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
The lpuart of imx8ulp is basically the same as imx7ulp, but it supports
some new features based on imx7ulp, such as it can assert the DMA
request on EOP(end-of-packet).
Here add lpuart support for imx8ulp, and rx_watermark is set to 3 as
imx8ulp RX FIFO depth is 8.
Signed-off-by: Sherry Sun <sherry.sun@nxp.com>
Link: https://lore.kernel.org/r/20230130064449.9564-7-sherry.sun@nxp.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Add RTS watermark support for LPUART. The RX RTS_B output negates when
the number of empty words in the receive FIFO is greater or equal to
RTSWATER. Here set the RTSWATER to half of the rxfifo_size.
Signed-off-by: Sherry Sun <sherry.sun@nxp.com>
Link: https://lore.kernel.org/r/20230130064449.9564-6-sherry.sun@nxp.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
With the growth of rx watermark, it's useful to enable the Receiver Idle
Empty function, it can assert the RDRF(Receive Data Register Full Flag)
when the receiver is idle for a number of idle characters and the FIFO
is not empty. It will generate a DMA request or interrupt, which can
avoid receive data being trapped in the RX FIFO since the number of
words received is less than the watermark.
Here set the RXIDEN as 0x3 which enable the RDRF assertion due to
partially filled FIFO when receiver is idle for 4 characters.
Signed-off-by: Sherry Sun <sherry.sun@nxp.com>
Link: https://lore.kernel.org/r/20230130064449.9564-5-sherry.sun@nxp.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
The RXWATER value must be greater than 0 according to the LPUART
reference manual. And when the number of datawords in the receive
FIFO is greater than RXWATER, an interrupt or a DMA request is
generated, so no need to set the different value for lpuart interrupt
case and dma case. Here delete the wrong RXWATER setting for dma case
directly.
Fixes: 42b68768e51b ("serial: fsl_lpuart: DMA support for 32-bit variant")
Signed-off-by: Sherry Sun <sherry.sun@nxp.com>
Link: https://lore.kernel.org/r/20230130064449.9564-4-sherry.sun@nxp.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Since imx8qxp RX FIFO depth is 64 datawords, it will be better to set
the rx watermark as 31, which means when the number of datawords in the
receive FIFO(>= 32) is greater than the watermark, an interrupt or a DMA
request is generated.
Also keep the console rx watermark as 1 to make sure it responsive.
Signed-off-by: Sherry Sun <sherry.sun@nxp.com>
Link: https://lore.kernel.org/r/20230130064449.9564-3-sherry.sun@nxp.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Add rx_watermark parameter for struct lpuart_port to make the receive
watermark configurable for different platforms.
No function changed.
Signed-off-by: Sherry Sun <sherry.sun@nxp.com>
Link: https://lore.kernel.org/r/20230130064449.9564-2-sherry.sun@nxp.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
ready
lpuart32_setup_watermark_enable() will configure the UART FIFO and
watermark, also enable the receiver and transmitter, this should be done
after the rx/tx dma steup ready.
Also add lpuart32_hw_disable() to make sure the receiver/transmitter and
interrupts are disabled during the dma steup.
Signed-off-by: Sherry Sun <sherry.sun@nxp.com>
Link: https://lore.kernel.org/r/20230130054107.9119-1-sherry.sun@nxp.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Some SoCs like the i.MX93 have aliases for up to eight UARTs, see:
https://github.com/torvalds/linux/blob/v6.1/arch/arm64/boot/dts/freescale/imx93.dtsi#L31-L38
Increase UART_NR from 6 to 8 to support lpuart7 and lpuart8 and avoid
initialization failures like the following:
[ 0.837146] fsl-lpuart 42690000.serial: serial6 out of range
[ 0.842814] fsl-lpuart: probe of 42690000.serial failed with error -22
Signed-off-by: Nate Drude <nate.d@variscite.com>
Reviewed-by: Sherry Sun <sherry.sun@nxp.com>
Link: https://lore.kernel.org/r/20221222145634.2217793-1-nate.d@variscite.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Need to disable the break condition for lpuart driver when closing
the uart port like other uart drivers do.
Signed-off-by: Sherry Sun <sherry.sun@nxp.com>
Link: https://lore.kernel.org/r/20221214031137.28815-3-sherry.sun@nxp.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
LPUART IP has a bug that it treats the CTS as higher priority than the
break signal, which cause the break signal sending through UARTCTRL_SBK
may impacted by the CTS input if the HW flow control is enabled.
Add this workaround patch to fix the IP bug, we can disable CTS before
asserting SBK to avoid any interference from CTS, and re-enable it when
break off.
Such as for the bluetooth chip power save feature, host can let the BT
chip get into sleep state by sending a UART break signal, and wake it up
by turning off the UART break. If the BT chip enters the sleep mode
successfully, it will pull up the CTS line, if the BT chip is woken up,
it will pull down the CTS line. If without this workaround patch, the
UART TX pin cannot send the break signal successfully as it affected by
the BT CTS pin. After adding this patch, the BT power save feature can
work well.
Signed-off-by: Sherry Sun <sherry.sun@nxp.com>
Link: https://lore.kernel.org/r/20221214031137.28815-2-sherry.sun@nxp.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
The LPUART Status Register needs to be cleared when closing the uart
port to get a clean environment when reopening the uart.
Fixes: 380c966c093e ("tty: serial: fsl_lpuart: add 32-bit register interface support")
Signed-off-by: Sherry Sun <sherry.sun@nxp.com>
Link: https://lore.kernel.org/r/20221125101953.18753-4-sherry.sun@nxp.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
UARTBAUD_RDMAE and UARTBAUD_TDMAE are enabled in lpuart32_startup(), but
lpuart32_shutdown() not disable them, only free the dma ring buffer and
release the dma channels, so here disable the Rx/Tx DMA first in
lpuart32_shutdown().
Fixes: 42b68768e51b ("serial: fsl_lpuart: DMA support for 32-bit variant")
Signed-off-by: Sherry Sun <sherry.sun@nxp.com>
Link: https://lore.kernel.org/r/20221125101953.18753-3-sherry.sun@nxp.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
For the lpuart driver, the Idle Line Interrupt Enable now is only needed
for the CPU mode, so enable the UARTCTRL_ILIE at the correct place, and
clear it when shutdown.
Also need to configure the suitable UARTCTRL_IDLECFG, now the value is
0x7, represent 128 idle characters will trigger the Idle Line Interrupt.
Signed-off-by: Sherry Sun <sherry.sun@nxp.com>
Link: https://lore.kernel.org/r/20221125101953.18753-2-sherry.sun@nxp.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Convert dmaengine_terminate_all() calls to synchronous and asynchronous
versions where appropriate.
Signed-off-by: Sherry Sun <sherry.sun@nxp.com>
Link: https://lore.kernel.org/r/20221123023619.30173-1-sherry.sun@nxp.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Use pm_ptr() to remove the need to mark the pm functions as
__maybe_unused when the kernel is built without CONFIG_PM support.
Signed-off-by: Sherry Sun <sherry.sun@nxp.com>
Link: https://lore.kernel.org/r/20221110113859.8485-4-sherry.sun@nxp.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Add runtime pm support to manage the lpuart clock.
Signed-off-by: Sherry Sun <sherry.sun@nxp.com>
Link: https://lore.kernel.org/r/20221110113859.8485-3-sherry.sun@nxp.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
LPUART supports both synchronous wakeup and asynchronous wakeup(wakeup
the system when the UART clocks are shut-off), the synchronous wakeup is
configured by UARTCTRL_RIE interrupt, and the asynchronous wakeup is
configured by UARTBAUD_RXEDGIE interrupt.
Add lpuart_uport_is_active() to determine if the uart port needs to get
into the suspend states, also add lpuart_suspend_noirq() and
lpuart_resume_noirq() to enable and disable the wakeup irq bits if the
uart port needs to be set as wakeup source.
When use lpuart with DMA mode, it still needs to switch to the cpu mode
in .suspend() that enable cpu interrupts RIE and RXEDGIE as wakeup
source, after system resume back, needs to setup DMA again, .resume()
will share the HW setup code with .startup(), so abstract the same code
to the api like lpuart32_hw_setup().
Signed-off-by: Sherry Sun <sherry.sun@nxp.com>
Link: https://lore.kernel.org/r/20221110113859.8485-2-sherry.sun@nxp.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
We need the tty/serial fixes in here as well.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
lpuart_global_reset() shouldn't break the on-going transmit engine, need
to recover the on-going data transfer after reset.
This can help earlycon here, since commit 60f361722ad2 ("serial:
fsl_lpuart: Reset prior to registration") moved lpuart_global_reset()
before uart_add_one_port(), earlycon is writing during global reset,
as global reset will disable the TX and clear the baud rate register,
which caused the earlycon cannot work any more after reset, needs to
restore the baud rate and re-enable the transmitter to recover the
earlycon write.
Also move the lpuart_global_reset() down, then we can reuse the
lpuart32_tx_empty() without declaration.
Fixes: bd5305dcabbc ("tty: serial: fsl_lpuart: do software reset for imx7ulp and imx8qxp")
Signed-off-by: Sherry Sun <sherry.sun@nxp.com>
Link: https://lore.kernel.org/r/20221024085844.22786-1-sherry.sun@nxp.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Take advantage of the new uart_xmit_advance() helper.
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Link: https://lore.kernel.org/r/20221019091151.6692-17-ilpo.jarvinen@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
uart_port_tx() is a new helper to send characters to the device. Use it
in these drivers.
Cc: Tobias Klauser <tklauser@distanz.ch>
Cc: Richard Genoud <richard.genoud@gmail.com>
Cc: Nicolas Ferre <nicolas.ferre@microchip.com>
Cc: Alexandre Belloni <alexandre.belloni@bootlin.com>
Cc: Claudiu Beznea <claudiu.beznea@microchip.com>
Cc: Vladimir Zapolskiy <vz@mleia.com>
Cc: Liviu Dudau <liviu.dudau@arm.com>
Cc: Sudeep Holla <sudeep.holla@arm.com>
Cc: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Cc: Shawn Guo <shawnguo@kernel.org>
Cc: Sascha Hauer <s.hauer@pengutronix.de>
Cc: Pengutronix Kernel Team <kernel@pengutronix.de>
Cc: Fabio Estevam <festevam@gmail.com>
Cc: NXP Linux Team <linux-imx@nxp.com>
Cc: "Andreas Färber" <afaerber@suse.de>
Cc: Manivannan Sadhasivam <mani@kernel.org>
Reviewed-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Signed-off-by: Jiri Slaby (SUSE) <jirislaby@kernel.org>
Link: https://lore.kernel.org/r/20221004104927.14361-3-jirislaby@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
When a UART port is newly registered, uart_configure_port() seeks to
deassert RS485 Transmit Enable by setting the RTS bit in port->mctrl.
However a number of UART drivers interpret a set RTS bit as *assertion*
instead of deassertion: Affected drivers include those using
serial8250_em485_config() (except 8250_bcm2835aux.c) and some using
mctrl_gpio (e.g. imx.c).
Since the interpretation of the RTS bit is driver-specific, it is not
suitable as a means to centrally deassert Transmit Enable in the serial
core. Instead, the serial core must call on drivers to deassert it in
their driver-specific way. One way to achieve that is to call
->rs485_config(). It implicitly deasserts Transmit Enable.
So amend uart_configure_port() and uart_resume_port() to invoke
uart_rs485_config(). That allows removing calls to uart_rs485_config()
from drivers' ->probe() hooks and declaring the function static.
Skip any invocation of ->set_mctrl() if RS485 is enabled. RS485 has no
hardware flow control, so the modem control lines are irrelevant and
need not be touched. When leaving RS485 mode, reset the modem control
lines to the state stored in port->mctrl. That way, UARTs which are
muxed between RS485 and RS232 transceivers drive the lines correctly
when switched to RS232. (serial8250_do_startup() historically raises
the OUT1 modem signal because otherwise interrupts are not signaled on
ancient PC UARTs, but I believe that no longer applies to modern,
RS485-capable UARTs and is thus safe to be skipped.)
imx.c modifies port->mctrl whenever Transmit Enable is asserted and
deasserted. Stop it from doing that so port->mctrl reflects the RS232
line state.
8250_omap.c deasserts Transmit Enable on ->runtime_resume() by calling
->set_mctrl(). Because that is now a no-op in RS485 mode, amend the
function to call serial8250_em485_stop_tx().
fsl_lpuart.c retrieves and applies the RS485 device tree properties
after registering the UART port. Because applying now happens on
registration in uart_configure_port(), move retrieval of the properties
ahead of uart_add_one_port().
Link: https://lore.kernel.org/all/20220329085050.311408-1-matthias.schiffer@ew.tq-group.com/
Link: https://lore.kernel.org/all/8f538a8903795f22f9acc94a9a31b03c9c4ccacb.camel@ginzinger.com/
Fixes: d3b3404df318 ("serial: Fix incorrect rs485 polarity on uart open")
Cc: stable@vger.kernel.org # v4.14+
Reported-by: Matthias Schiffer <matthias.schiffer@ew.tq-group.com>
Reported-by: Roosen Henri <Henri.Roosen@ginzinger.com>
Tested-by: Matthias Schiffer <matthias.schiffer@ew.tq-group.com>
Reviewed-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Link: https://lore.kernel.org/r/2de36eba3fbe11278d5002e4e501afe0ceaca039.1663863805.git.lukas@wunner.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty") into tty-next
We need the tty fixes and api additions in this branch.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Since commit bd5305dcabbc ("tty: serial: fsl_lpuart: do software reset
for imx7ulp and imx8qxp"), certain i.MX UARTs are reset after they've
already been registered. Register state may thus be clobbered after
user space has begun to open and access the UART.
Avoid by performing the reset prior to registration.
Fixes: bd5305dcabbc ("tty: serial: fsl_lpuart: do software reset for imx7ulp and imx8qxp")
Cc: stable@vger.kernel.org # v5.15+
Cc: Fugang Duan <fugang.duan@nxp.com>
Cc: Sherry Sun <sherry.sun@nxp.com>
Reviewed-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Link: https://lore.kernel.org/r/72fb646c1b0b11c989850c55f52f9ff343d1b2fa.1662884345.git.lukas@wunner.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
lpuart_dma_shutdown tears down lpuart dma, but lpuart_flush_buffer can
still occur which in turn tries to access dma apis if lpuart_dma_tx_use
flag is true. At this point since dma is torn down, these dma apis can
abort. Set lpuart_dma_tx_use and the corresponding rx flag
lpuart_dma_rx_use to false in lpuart_dma_shutdown so that dmas are not
accessed after they are relinquished.
Otherwise, when try to kill btattach, kernel may panic. This patch may
fix this issue.
root@imx8ulpevk:~# btattach -B /dev/ttyLP2 -S 115200
^C[ 90.182296] Internal error: synchronous external abort: 96000210 [#1] PREEMPT SMP
[ 90.189806] Modules linked in: moal(O) mlan(O)
[ 90.194258] CPU: 0 PID: 503 Comm: btattach Tainted: G O 5.15.32-06136-g34eecdf2f9e4 #37
[ 90.203554] Hardware name: NXP i.MX8ULP 9X9 EVK (DT)
[ 90.208513] pstate: 600000c5 (nZCv daIF -PAN -UAO -TCO -DIT -SSBS BTYPE=--)
[ 90.215470] pc : fsl_edma3_disable_request+0x8/0x60
[ 90.220358] lr : fsl_edma3_terminate_all+0x34/0x20c
[ 90.225237] sp : ffff800013f0bac0
[ 90.228548] x29: ffff800013f0bac0 x28: 0000000000000001 x27: ffff000008404800
[ 90.235681] x26: ffff000008404960 x25: ffff000008404a08 x24: ffff000008404a00
[ 90.242813] x23: ffff000008404a60 x22: 0000000000000002 x21: 0000000000000000
[ 90.249946] x20: ffff800013f0baf8 x19: ffff00000559c800 x18: 0000000000000000
[ 90.257078] x17: 0000000000000000 x16: 0000000000000000 x15: 0000000000000000
[ 90.264211] x14: 0000000000000003 x13: 0000000000000000 x12: 0000000000000040
[ 90.271344] x11: ffff00000600c248 x10: ffff800013f0bb10 x9 : ffff000057bcb090
[ 90.278477] x8 : fffffc0000241a08 x7 : ffff00000534ee00 x6 : ffff000008404804
[ 90.285609] x5 : 0000000000000000 x4 : 0000000000000000 x3 : ffff0000055b3480
[ 90.292742] x2 : ffff8000135c0000 x1 : ffff00000534ee00 x0 : ffff00000559c800
[ 90.299876] Call trace:
[ 90.302321] fsl_edma3_disable_request+0x8/0x60
[ 90.306851] lpuart_flush_buffer+0x40/0x160
[ 90.311037] uart_flush_buffer+0x88/0x120
[ 90.315050] tty_driver_flush_buffer+0x20/0x30
[ 90.319496] hci_uart_flush+0x44/0x90
[ 90.323162] +0x34/0x12c
[ 90.327253] tty_ldisc_close+0x38/0x70
[ 90.331005] tty_ldisc_release+0xa8/0x190
[ 90.335018] tty_release_struct+0x24/0x8c
[ 90.339022] tty_release+0x3ec/0x4c0
[ 90.342593] __fput+0x70/0x234
[ 90.345652] ____fput+0x14/0x20
[ 90.348790] task_work_run+0x84/0x17c
[ 90.352455] do_exit+0x310/0x96c
[ 90.355688] do_group_exit+0x3c/0xa0
[ 90.359259] __arm64_sys_exit_group+0x1c/0x20
[ 90.363609] invoke_syscall+0x48/0x114
[ 90.367362] el0_svc_common.constprop.0+0xd4/0xfc
[ 90.372068] do_el0_svc+0x2c/0x94
[ 90.375379] el0_svc+0x28/0x80
[ 90.378438] el0t_64_sync_handler+0xa8/0x130
[ 90.382711] el0t_64_sync+0x1a0/0x1a4
[ 90.386376] Code: 17ffffda d503201f d503233f f9409802 (b9400041)
[ 90.392467] ---[ end trace 2f60524b4a43f1f6 ]---
[ 90.397073] note: btattach[503] exited with preempt_count 1
[ 90.402636] Fixing recursive fault but reboot is needed!
Fixes: 6250cc30c4c4 ("tty: serial: fsl_lpuart: Use scatter/gather DMA for Tx")
Reviewed-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Signed-off-by: Thara Gopinath <tgopinath@microsoft.com>
Signed-off-by: Sherry Sun <sherry.sun@nxp.com>
Link: https://lore.kernel.org/r/20220920111703.1532-1-sherry.sun@nxp.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
We need the tty/serial fixes in here as well.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
engine to complete
When the user initializes the uart port, and waits for the transmit
engine to complete in lpuart32_set_termios(), if the UART TX fifo has
dirty data and the UARTMODIR enable the flow control, the TX fifo may
never be empty. So here we should disable the flow control first to make
sure the transmit engin can complete.
Fixes: 380c966c093e ("tty: serial: fsl_lpuart: add 32-bit register interface support")
Cc: stable <stable@kernel.org>
Signed-off-by: Sherry Sun <sherry.sun@nxp.com>
Link: https://lore.kernel.org/r/20220821101527.10066-1-sherry.sun@nxp.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
The setting of RS485 RTS polarity is inverse in the current driver.
When the property of 'rs485-rts-active-low' is enabled in the dts node,
the RTS signal should be LOW during sending. Otherwise, if there is no
such a property, the RTS should be HIGH during sending.
Fixes: 03895cf41d18 ("tty: serial: fsl_lpuart: Add support for RS-485")
Cc: stable <stable@kernel.org>
Signed-off-by: Nicolas Diaz <nicolas.diaz@nxp.com>
Signed-off-by: Shenwei Wang <shenwei.wang@nxp.com>
Link: https://lore.kernel.org/r/20220805144529.604856-1-shenwei.wang@nxp.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
The number of bits can be calculated using tty_get_frame_size(), no
need for the driver to do it on its own. Change bits to unsigned and
baud too since we're touching the declarations line anyway (the
respective core functions are typed unsigned).
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Link: https://lore.kernel.org/r/20220830084925.5608-4-ilpo.jarvinen@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
There should be no reason to adjust old ktermios which is going to get
discarded anyway.
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Link: https://lore.kernel.org/r/20220816115739.10928-7-ilpo.jarvinen@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
The double `as' is duplicated in the comment, remove one.
Signed-off-by: Jason Wang <wangborong@cdjrlc.com>
Link: https://lore.kernel.org/r/20220803104208.4127-1-wangborong@cdjrlc.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
The LPUART can't distinguish between a break signal and a framing error,
so need to count the break characters if there is a framing error and
received data is zero instead of the parity error.
Fixes: 5541a9bacfe5 ("serial: fsl_lpuart: handle break and make sysrq work")
Reviewed-by: Michael Walle <michael@walle.cc>
Signed-off-by: Sherry Sun <sherry.sun@nxp.com>
Link: https://lore.kernel.org/r/20220725050115.12396-1-sherry.sun@nxp.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
The LPUART hardware doesn't zero out the parity bit on the received
characters. This behavior won't impact the use cases of CS8 because
the parity bit is the 9th bit which is not currently used by software.
But the parity bit for CS7 must be zeroed out by software in order to
get the correct raw data.
Signed-off-by: Shenwei Wang <shenwei.wang@nxp.com>
Link: https://lore.kernel.org/r/20220714185858.615373-1-shenwei.wang@nxp.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Embed rs485_supported to uart_port to allow serial core to tweak it as
needed.
Reviewed-by: Lino Sanfilippo <l.sanfilippo@kunbus.com>
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Link: https://lore.kernel.org/r/20220704094515.6831-2-ilpo.jarvinen@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
To be able to alter ADDRB within ->rs485_config(), take termios_rwsem
before calling ->rs485_config() and pass termios.
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Link: https://lore.kernel.org/r/20220624204210.11112-5-ilpo.jarvinen@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Serial core handles serial_rs485 sanitization. Remove custom
sanitization from lpuart_config_rs485.
This change loses dev_err when SER_RS485_RX_DURING_TX is set due to
incorrect configuration. Other drivers do not do similar prinout for
full-duplex case and it should be done in serial core if it is
desirable to notify on this condition. Personally, I doesn't see it
important because the kernel gracefully downgrades to half-duplex.
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Link: https://lore.kernel.org/r/20220606100433.13793-31-ilpo.jarvinen@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Add information on supported serial_rs485 features.
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Link: https://lore.kernel.org/r/20220606100433.13793-16-ilpo.jarvinen@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
A few serial drivers make a call to rs485_config() themselves (all
these seem to relate to init). Convert them all to use a common helper
which makes it easy to make adjustments on tasks related to it as
serial_rs485 struct sanitization is going to be added.
In pci_fintek_setup() (in 8250_pci.c), the rs485_config() call was made
with NULL, however, it can be changed to pass uart_port's rs485 struct.
No other callers should pass NULL into rs485_config() so the NULL check
can now be eliminated.
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Link: https://lore.kernel.org/r/20220606100433.13793-2-ilpo.jarvinen@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
if (termios->c_cflag & CRTSCTS) guarantees that CRTSCTS is not ever set
in the else block so clearing it is unnecessary.
While at it, remove also one pair of extra parenthesis.
Reviewed-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Link: https://lore.kernel.org/r/20220513082906.11096-5-ilpo.jarvinen@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
We need the tty fixes in here as well, as we need to revert one of them :(
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
If an irq is pending when devm_request_irq() is called, the irq
handler will cause a NULL pointer access because initialisation
is not done yet.
Fixes: 9d7ee0e28da59 ("tty: serial: lpuart: avoid report NULL interrupt")
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Indan Zupancic <Indan.Zupancic@mep-info.com>
Link: https://lore.kernel.org/r/20220505114750.45423-1-Indan.Zupancic@mep-info.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
No need to initialize the count variable in lpuart_copy_rx_to_tty(),
so let's remove it here.
Reviewed-by: Jiri Slaby <jirislaby@kernel.org>
Signed-off-by: Sherry Sun <sherry.sun@nxp.com>
Link: https://lore.kernel.org/r/20220418021844.29591-1-sherry.sun@nxp.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
and ida_simple_get
Now fsl_lpuart driver use both of_alias_get_id() and ida_simple_get() in
.probe(), which has the potential bug. For example, when remove the
lpuart7 alias in dts, of_alias_get_id() will return error, then call
ida_simple_get() to allocate the id 0 for lpuart7, this may confilct
with the lpuart4 which has alias 0.
aliases {
...
serial0 = &lpuart4;
serial1 = &lpuart5;
serial2 = &lpuart6;
serial3 = &lpuart7;
}
So remove the ida_simple_get() in .probe(), return an error directly
when calling of_alias_get_id() fails, which is consistent with other
uart drivers behavior.
Fixes: 3bc3206e1c0f ("serial: fsl_lpuart: Remove the alias node dependence")
Signed-off-by: Sherry Sun <sherry.sun@nxp.com>
Link: https://lore.kernel.org/r/20220321112211.8895-1-sherry.sun@nxp.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|