| Age | Commit message (Collapse) | Author |
|---|
|
Several versions of DW DMAC have multi block transfers hardware
support. Hardware support of multi block transfers is disabled
by default if we use DT to configure DMAC and software emulation
of multi block transfers used instead.
Add multi-block property, so it is possible to enable hardware
multi block transfers (if present) via DT.
Switch from per device is_nollp variable to multi_block array
to be able enable/disable multi block transfers separately per
channel.
Acked-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Eugeniy Paltsev <Eugeniy.Paltsev@synopsys.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
|
|
During a PCI error recovery, like the ones provoked by EEH in the ppc64
platform, all IO to the device must be blocked while the recovery is
completed. Current 8250_pci implementation only suspends the port
instead of detaching it, which doesn't prevent incoming accesses like
TIOCMGET and TIOCMSET calls from reaching the device. Those end up
racing with the EEH recovery, crashing it. Similar races were also
observed when opening the device and when shutting it down during
recovery.
This patch implements a more robust IO blockage for the 8250_pci
recovery by unregistering the port at the beginning of the procedure and
re-adding it afterwards. Since the port is detached from the uart
layer, we can be sure that no request will make through to the device
during recovery. This is similar to the solution used by the JSM serial
driver.
I thank Peter Hurley <peter@hurleysoftware.com> for valuable input on
this one over one year ago.
Signed-off-by: Gabriel Krisman Bertazi <krisman@linux.vnet.ibm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Add a set_ldisc function to enable/disable IrDA SIR mode according to
the new line discipline, if IrDA SIR mode is supported by the hardware
configuration.
Signed-off-by: Ed Blake <ed.blake@imgtec.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Expose set_ldisc() function so that it can be overridden with a
platform specific implementation.
Signed-off-by: Ed Blake <ed.blake@imgtec.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Add an IrDA UART capability flag and change the type of
uart_8250_port.capabilities to be u32 rather than unsigned short to
accommodate the additional flag.
Signed-off-by: Ed Blake <ed.blake@imgtec.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
When any 8250 based driver sets up DMA and has UART_CAP_RPM capability enabled
the device is left powered on after transfer is done. We need to schedule a
device suspend operation when DMA completes the transfer.
The patch is based on the work done by the reporter.
Reported-by: Huiquan Zhong <huiquan.zhong@intel.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
The following fix of runtime PM use in DMA mode requires at least
serial8250_rpm_put_tx() to be available. Export both calls.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
The fresh new serial driver for pxa produces warnings when
CONFIG_PM_SLEEP is disabled:
drivers/tty/serial/8250/8250_pxa.c:50:12: error: 'serial_pxa_resume' defined but not used [-Werror=unused-function]
drivers/tty/serial/8250/8250_pxa.c:41:12: error: 'serial_pxa_suspend' defined but not used [-Werror=unused-function]
This removes the #ifdef around the two functions and instead marks both
as __maybe_unused, which is more robust and avoids the warning.
Fixes: ab28f51c77cd ("serial: rewrite pxa2xx-uart to use 8250_core")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Robert Jarzmik <robert.jarzmik@free.fr>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Hi,
below patch to fix Fourth port offset of Percom PI7C9X7954 boards.
I had a problem using Fourth port on a pci express serial board based on Pericom
PI7C9X7954. Reading datasheet I notice a "special" offset assign to this port
when used in I/O mode.
Offset 0x0 -> UART 0
Offset 0x8 -> UART 1
Offset 0x10 -> UART 2
Offset 0x38 -> UART 3 <<---- This don't follow a logical sequence
This patch add a different init to last port, to have right offset.
I check also Pericom 7952 and 7958 but that devices follow logical sequence,
so they are ok.
Regards,
Angelo
Signed-off-by: Angelo Butti <buttiangelo@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
The newly added pxa glue driver for 8250 supports console output, but
fails to build if the 8250 console is disabled:
drivers/tty/serial/8250/8250_pxa.o: In function `early_serial_pxa_setup':
8250_pxa.c:(.init.text+0x50): undefined reference to `early_serial8250_setup'
This adds an #ifdef like the other glue drivers have it.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Robert Jarzmik <robert.jarzmik@free.fr>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
The hardware book says, the FCR is combined with a register called
CHAR (it will trigger interrupt when a specific character is
received). At first, I used lock/read/modify/write/unlock dance for
the FCR to not affect the upper bits, but the CHAR is actually never
used. It should not hurt to always clear the CHAR and to handle the
FCR as a normal case. It can save the costly locking.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Suggested-by: Denys Vlasenko <dvlasenk@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
For this driver, uart_port::regshift is always 2. Hardcode the
shift value instead of reading ->regshift to get an already known
value. (pointed out by Denys Vlasenko)
Furthermore, I am using register macros that are already shifted,
which will save code a bit.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
We want the serial/tty fixes in here as well.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
NXP SC16C2552 requires that we always write a reset to the RX FIFO and
TX FIFO whenever we enable the FIFOs
Cc: xe-kernel@external.cisco.com
Signed-off-by: Steve Shih <sshih@cisco.com>
Signed-off-by: David Singleton <davsingl@cisco.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Fintek F81865 is a LPC to 6 UARTs SuperIO. It has less functional UARTs
likes F81866. It's also need check the IRQ mode with system assigned,
but the configuration is not the same with F81216 series.
F81865 IRQ Mode setting:
0xf0
Bit1: IRQ_MODE0
Bit0: Share mode (always on)
Level/Low: IRQ_MODE0:0
Edge/High: IRQ_MODE0:1
The following list is brief descriptions of F81865:
F81865 (0704)
9Bit(not implements with mainline)
RS485(implemented)
Suggested-by: Ricardo Ribalda Delgado <ricardo.ribalda@gmail.com>
Signed-off-by: Ji-Ze Hong (Peter Hong) <hpeter+linux_kernel@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Fintek F81866 is a LPC to 6 UARTs SuperIO. It has fully functional UARTs
likes F81216H. It's also need check the IRQ mode with system assigned,
but the configuration is not the same with F81216 series.
F81866 IRQ Mode setting:
0xf0
Bit1: IRQ_MODE0
Bit0: Share mode (always on)
0xf6
Bit3: IRQ_MODE1
Level/Low: IRQ_MODE0:0, IRQ_MODE1:0
Edge/High: IRQ_MODE0:1, IRQ_MODE1:0
The following list is brief descriptions of F81866:
F81866 (1010)
9Bit/High baud rate(not implements with mainline)
RS485, 128Bytes FIFO (implemented)
Signed-off-by: Ji-Ze Hong (Peter Hong) <hpeter+linux_kernel@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Fintek F81216 is a LPC to 4 UARTs device. It's the F81216 series but
support less functional than F81216AD/F81216H
The following list is brief descriptions of F81216 series:
F81216H (0105)
9Bit/High baud rate(not implements with mainline)
RS485, 128Bytes FIFO (implemented)
F81216AD (0216)
9Bit(not implements with mainline)
RS485(implemented)
F81216 (0208)
basically 16550A
Suggested-by: Ricardo Ribalda Delgado <ricardo.ribalda@gmail.com>
Signed-off-by: Ji-Ze Hong (Peter Hong) <hpeter+linux_kernel@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
The Fintek F81216H had maximum 128Bytes FIFO, but some BIOS configurated
as normal 16Bytes FIFO. This patch will set 128Bytes FIFO and trigger
level multiplier as 4x when F81216H detected.
Default 16550A trigger level is 8Bytes. When this patch applied, the
trigger level will change to 8Byte x 4 = 32Byte. It can be reduce the RX
incoming interrupts.
Suggested-by: Ricardo Ribalda Delgado <ricardo.ribalda@gmail.com>
Signed-off-by: Ji-Ze Hong (Peter Hong) <hpeter+linux_kernel@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Set IRQ Mode when port probed in probe_setup_port()
It should hold the IO port premission via fintek_8250_enter_key() and
release via fintek_8250_exit_key() when we configure the SuperIO.
This patch will move all SuperIO configure operations to
probe_setup_port() to reduce fintek_8250_enter_key() and
fintek_8250_exit_key() usage.
Suggested-by: Ricardo Ribalda Delgado <ricardo.ribalda@gmail.com>
Signed-off-by: Ji-Ze Hong (Peter Hong) <hpeter+linux_kernel@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
If we need to access SuperIO registers, It should write register offset
to base_addr and read/write value to base_addr + 1 to perform read/write.
We can make it more simply with write/read functions.
This patch add sio_read_reg()/sio_write_reg()/sio_write_mask_reg() to
reduce SuperIO register operation with lot of outb()/inb().
Signed-off-by: Ji-Ze Hong (Peter Hong) <hpeter+linux_kernel@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Transfer the device-tree pxa uart handling from 8250_of to the new
8250_pxa. As a corollary, add the early console definition into
8250_pxa.
This enables to have the same uart node for the early console and the
normal uart.
Signed-off-by: Robert Jarzmik <robert.jarzmik@free.fr>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Instead of a direct assignment use pci_irq_vector() call as it's done for the
other case.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Enable MWI mechanism if PCI bus master supports it.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
There is no need to set PCI bus mastering when device is not doing any DMA.
Though on Intel Quark DMA is a part of UART IP and thus shares same device in
Linux kernel.
Enable bus mastering only for Quark case.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
The commit 4fe0d154880b ("PCI: Use positive flags in pci_alloc_irq_vectors()")
replaces flags from negative to positive values which makes mandatory to have
the last argument in pci_alloc_irq_vectors() non-zero (if we want to be no-op).
This basically drops MSI enabling in 8250_lpss driver.
Restore desired behaviour in 8250_lpss by passing PCI_IRQ_ALL_TYPES instead of
0 to pci_alloc_irq_vectors().
Fixes: 60a9244a5d14 ("serial: 8250_lpss: enable MSI for Intel Quark")
Cc: Christoph Hellwig <hch@lst.de>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Bryan O'Donoghue <pure.logic@nexus-software.ie>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
pxa2xx-uart was a separate uart platform driver. It was declaring
the same device names and numbers as 8250 driver. As a result,
it was impossible to use 8250 driver on PXA SoCs.
Upon closer examination pxa2xx-uart turned out to be a clone of
8250_core driver.
Workaround for Erratum #19 according to Marvel(R) PXA270M Processor
Specification Update (April 19, 2010) is dropped. 8250_core reads
from FIFO immediately after checking DR bit in LSR.
The patch leaves the original SERIAL_PXA driver around. The original
driver is just marked DEPRECATED in Kconfig and C source. When
the original driver is considered safe to remove, no changes
to SERIAL_8250 will be necessary.
Compiling SERIAL_8250_CONSOLE and SERIAL_PXA_CONSOLE even without
SERIAL_8250_PXA breaks console for SERIAL_PXA. For this reasons, the new
and the original drivers are made mutually exclusive.
Signed-off-by: Sergei Ianovich <ynvich@gmail.com>
CC: Heikki Krogerus <heikki.krogerus@linux.intel.com>
CC: James Cameron <quozl@laptop.org>
CC: Robert Jarzmik <robert.jarzmik@free.fr>
CC: Russell King <linux@arm.linux.org.uk>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
[rebased on v4.8]
Tested-by: Robert Jarzmik <robert.jarzmik@free.fr>
Signed-off-by: Robert Jarzmik <robert.jarzmik@free.fr>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
At this point, 'value' is always a byte, then this code is clearing
bit 15, which is already clear. I meant to clear bit 7.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Reported-by: Denys Vlasenko <dvlasenk@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Commit 1681d2116c96 ("serial: 8250_uniphier: add "\n" at the end of
error log") missed this.
Signed-off-by: Denys Vlasenko <dvlasenk@redhat.com>
[masahiro: add commit log]
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty
Pull tty and serial updates from Greg KH:
"Here is the big tty and serial patch set for 4.9-rc1.
It also includes some drivers/dma/ changes, as those were needed by
some serial drivers, and they were all acked by the DMA maintainer.
Also in here is the long-suffering ACPI SPCR patchset, which was
passed around from maintainer to maintainer like a hot-potato. Seems I
was the sucker^Wlucky one. All of those patches have been acked by the
various subsystem maintainers as well.
All of this has been in linux-next with no reported issues"
* tag 'tty-4.9-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty: (111 commits)
Revert "serial: pl011: add console matching function"
MAINTAINERS: update entry for atmel_serial driver
serial: pl011: add console matching function
ARM64: ACPI: enable ACPI_SPCR_TABLE
ACPI: parse SPCR and enable matching console
of/serial: move earlycon early_param handling to serial
Revert "drivers/tty: Explicitly pass current to show_stack"
tty: amba-pl011: Don't complain on -EPROBE_DEFER when no irq
nios2: dts: 10m50: Add tx-threshold parameter
serial: 8250: Set Altera 16550 TX FIFO Threshold
serial: 8250: of: Load TX FIFO Threshold from DT
Documentation: dt: serial: Add TX FIFO threshold parameter
drivers/tty: Explicitly pass current to show_stack
serial: imx: Fix DCD reading
serial: stm32: mark symbols static where possible
serial: xuartps: Add some register initialisation to cdns_early_console_setup()
serial: xuartps: Removed unwanted checks while reading the error conditions
serial: xuartps: Rewrite the interrupt handling logic
serial: stm32: use mapbase instead of membase for DMA
tty/serial: atmel: fix fractional baud rate computation
...
|
|
* device-properties:
serial: 8250_dw: Add quirk for APM X-Gene SoC
ACPI / LPSS: Provide build-in properties of the UART
ACPI / APD: Provide build-in properties of the UART
driver core: Don't leak secondary fwnode on device removal
|
|
The Altera 16550 soft IP UART requires 2 additional registers for
TX FIFO threshold support. These 2 registers enable the TX FIFO
Low Watermark and set the TX FIFO Low Watermark.
Set the TX FIFO threshold to the FIFO size - tx_loadsz.
Signed-off-by: Thor Thayer <tthayer@opensource.altera.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Initialize the tx_loadsz parameter from passed in devicetree
tx-threshold parameter.
The tx_loadsz is calculated as the number of bytes to fill FIFO
when tx-threshold is triggered.
Signed-off-by: Thor Thayer <tthayer@opensource.altera.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
First loop in wait_for_xmitr could also trigger NMI
watchdog in case reading from the port is slow:
PID: 0 TASK: ffffffff819c1460 CPU: 0 COMMAND: "swapper/0"
#0 [ffff88019f405e58] crash_nmi_callback at ffffffff8104d382
#1 [ffff88019f405e68] nmi_handle at ffffffff8168ead9
#2 [ffff88019f405eb0] do_nmi at ffffffff8168ec53
#3 [ffff88019f405ef0] end_repeat_nmi at ffffffff8168df13
[exception RIP: delay_tsc+50]
RIP: ffffffff81325642 RSP: ffff88019f403bb0 RFLAGS: 00000083
RAX: 00000000000005c8 RBX: ffffffff81f83000 RCX: 0000024e4fb88a8b
RDX: 0000024e4fb89053 RSI: 0000000000000000 RDI: 00000000000007d1
RBP: ffff88019f403bb0 R8: 000000000000000a R9: 0000000000000000
R10: 0000000000000000 R11: ffff88019f403ad6 R12: 000000000000250f
R13: 0000000000000020 R14: ffffffff81d360c7 R15: 0000000000000047
ORIG_RAX: ffffffffffffffff CS: 0010 SS: 0018
--- <NMI exception stack> ---
#4 [ffff88019f403bb0] delay_tsc at ffffffff81325642
#5 [ffff88019f403bb8] __const_udelay at ffffffff813255a8
#6 [ffff88019f403bc8] wait_for_xmitr at ffffffff81404390
#7 [ffff88019f403bf0] serial8250_console_putchar at ffffffff8140455c
#8 [ffff88019f403c10] uart_console_write at ffffffff813ff00a
#9 [ffff88019f403c40] serial8250_console_write at ffffffff814044ae
#10 [ffff88019f403c88] call_console_drivers.constprop.15 at ffffffff81086b01
#11 [ffff88019f403cb0] console_unlock at ffffffff8108842f
#12 [ffff88019f403ce8] vprintk_emit at ffffffff81088834
#13 [ffff88019f403d58] vprintk_default at ffffffff81088ba9
#14 [ffff88019f403d68] printk at ffffffff8167f034
Adding touch_nmi_watchdog call to the first loop as well.
Reported-by: Chunyu Hu <chuhu@redhat.com>
Signed-off-by: Jiri Olsa <jolsa@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Less magic that only requires comments.
Signed-off-by: Jan Kiszka <jan.kiszka@siemens.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
We want the fixes in here for merge issues.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Since we have nice macro IRQ_RETVAL() we would use it to convert a flag of
handled interrupt from int to irqreturn_t.
The rationale of doing this is:
a) hence we implicitly mark hsu_dma_do_irq() as an auxiliary function that
can't be used as interrupt handler directly, and
b) to be in align with serial driver which is using serial8250_handle_irq()
that returns plain int by design.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
addresses
earlycon implementation used "unsigned long" internally, but there are systems
(ARM with LPAE) where sizeof(unsigned long) == 4 and uart is mapped beyond 4GiB
address range.
Switch to resource_size_t internally and replace obsoleted simple_strtoul() with
kstrtoull().
Signed-off-by: Alexander Sverdlin <alexander.sverdlin@nokia.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Add ACPI identifier for UART on Hisilicon Hip05 SoC, be careful that
it is not 16550 compatible, and "reg-io-width" and "reg-shift" need
be set properly by _DSD method in DSDT.
Signed-off-by: Kefeng Wang <wangkefeng.wang@huawei.com>
Acked-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Unify the check of em485 variable to be either (em485) or (!em485) instead of
the explicit comparison to NULL.
While here, remove redundant check in __do_stop_tx_rs485() and
__stop_tx_rs485() since the functions ain't called with NULL value of em485
variable.
Cc: "Matwey V. Kornilov" <matwey@sai.msu.ru>
Tested-by: Yegor Yefremov <yegorslists@googlemail.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
There are calls to serial8250_rpm_{get|put}() in __do_stop_tx_rs485() that are
certainly placed in a wrong location. I dunno how it had been tested with
runtime PM enabled because it is obvious "sleep in atomic context" error.
Besides that serial8250_rpm_get() is called immediately after an IO just
happened. It implies that the device is already powered on, see implementation
of serial8250_em485_rts_after_send() and serial8250_clear_fifos() for the
details.
There is no bug have been seen due to, as I can guess, use of auto suspend mode
when scheduled transaction to suspend is invoked quite lately than it's needed
for a few writes to the port. It might be possible to trigger a warning if
stop_tx_timer fires when device is suspended.
Refactor the code to use runtime PM only in case of timer function.
Fixes: 0c66940d584d ("tty/serial/8250: fix RS485 half-duplex RX")
Cc: "Matwey V. Kornilov" <matwey@sai.msu.ru>
Tested-by: Yegor Yefremov <yegorslists@googlemail.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Use an unified new dev variable instead of &pdev->dev and p->dev
in probe function.
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Kefeng Wang <wangkefeng.wang@huawei.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
The APM X-Gene SoC UART is the only board that still needs
the hard-coded values, so handle it separately in
dw8250_quirks(). The other ACPI platforms are able to
provide the values with device properties.
Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
Added devices ids for acces i/o products quad and octal serial cards
that make use of existing Pericom PI7C9X7954 and PI7C9X7958
configurations .
Signed-off-by: Jimi Damon <jdamon@accesio.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
DMA on Intel Quark SoC is a part of UART IP block. Enable it.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Tested-by: Bryan O'Donoghue <pure.logic@nexus-software.ie>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Intel Quark SoC supports MSI for LPSS, in particular for UART. Enable MSI for
Intel Quark.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Tested-by: Bryan O'Donoghue <pure.logic@nexus-software.ie>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Intel Quark has DesignWare UART. Move the code from 8250_pci to 8250_lpss.
Reviewed-by: Bryan O'Donoghue <pure.logic@nexus-software.ie>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Tested-by: Bryan O'Donoghue <pure.logic@nexus-software.ie>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
The SoCs, such as Intel Braswell, have DesignWare UART IP. Split out the
support of such chips to a separate module which also will be used for Intel
Quark later.
The rationale to have the separate driver to be existing:
- Do not contaminate 8250_pci.c anymore with LPSS related quirks
- All of them are using same DMA engine and they are Designware IP which means
that in the future we might share the code between 8250_dw.c and 8250_lpss.c
- It reduces the kernel memory footprint on non-X86 machines where 8250_pci.c
is in use
Besides the split the driver also has been refactored, in particular a) the DMA
and port setup are separate functions, b) the two new structures lpss8250 and
lpss8250_board are introduced to keep necessary data instead of
pciserial_board, c) DMA parameters are passed to the DMA setup via mentioned
custom structure. Most of the changes are done due to the future support of
UART DMA on Intel Quark.
The Intel Quark UART DMA support is based on bits taking from BSP code
published by Intel earlier.
The driver does not use any specific power management. PCI core takes care of
the default behaviour during suspend and resume.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Tested-by: Bryan O'Donoghue <pure.logic@nexus-software.ie>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Intel Quark has 16550A compatible UART with autoflow feature enabled. It has
only 16 bytes of FIFO. Currently serial8250_do_set_termios() prevents to enable
autoflow since the minimum requirement of 32 bytes of FIFO size.
Drop a FIFO size limitation to allow autoflow control be enabled on such UARTs.
While here, comment out UART_CAP_AFE for PORT_AR7 since it wasn't working and
it will be not a good idea to use it in conjunction with trigger level of 1
byte.
Suggested-by: Peter Hurley <peter@hurleysoftware.com>
Reviewed-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Tested-by: Bryan O'Donoghue <pure.logic@nexus-software.ie>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Some UARTs, e.g. one is used in Intel Quark, have a different address base for
DMA operations. Introduce an additional field (per RX and TX DMA channels) in
struct uart_8250_dma to cover those cases.
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Tested-by: Bryan O'Donoghue <pure.logic@nexus-software.ie>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Convert dmaengine_terminate_all() calls to synchronous and asynchronous
versions where appropriate.
Reviewed-by: Peter Hurley <peter@hurleysoftware.com>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Tested-by: Bryan O'Donoghue <pure.logic@nexus-software.ie>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
