| Age | Commit message (Collapse) | Author |
|---|
|
Instead of hard-coding the register offsets put them into a struct
and set them in the probe function.
Signed-off-by: Jan Glauber <jglauber@cavium.com>
Tested-by: Steven J. Hill <steven.hill@cavium.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Storing the system clock frequency in struct octeon_spi avoids
calling the MIPS specific octeon_get_io_clock_rate() for every transfer.
Signed-off-by: Jan Glauber <jglauber@cavium.com>
Tested-by: Steven J. Hill <steven.hill@cavium.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Remove all calls to cvmx_read_csr()/cvmx_write_csr() and use
the portable readq()/writeq() functions.
Signed-off-by: Steven J. Hill <steven.hill@cavium.com>
Signed-off-by: Jan Glauber <jglauber@cavium.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
wait_for_completion_timeout returns unsigned long not int so the check for
<= 0 should be == 0 here, and the type unsigned long. The function return
is set to -ETIMEDOUT to reflect the actual problem.
Signed-off-by: Nicholas Mc Guire <hofrat@osadl.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
wait_for_completion_timeout returns unsigned long not int so the check for
<= 0 should be == 0 here.
Signed-off-by: Nicholas Mc Guire <hofrat@osadl.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
The Rockchip SPI controller's length register only supports 16-bits,
yielding a maximum length of 64KiB (the CTRLR1 register holds "length -
1"). Trying to transfer more than that (e.g., with a large SPI flash
read) will cause the driver to hang.
Now, it seems that while theoretically we should be able to program
CTRLR1 with 0xffff, and get a 64KiB transfer, but that also seems to
cause the core to choke, so stick with a maximum of 64K - 1 bytes --
i.e., 0xffff.
Signed-off-by: Brian Norris <briannorris@chromium.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Return IRQ_NONE from the interrupt handler if the handler is running, but
no interrupt was detected. This allows the system to recover in case of an
interrupt storm due to an invalid interrupt configuration or faulty
hardware.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Acked-by: Ricardo Ribalda Delgado <ricardo.ribalda@gmail.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
The Xilinx SPI driver can operate without an IRQ, but not every error
returned by platform_get_irq() means that no IRQ was specified. It will
also return an error if the IRQ specification is invalid or the IRQ
provider is not yet available (EPROBE_DEFER).
So instead of ignoring all errors only ignore ENXIO, which means no IRQ was
specified, and propagate all other errors to device driver core.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Acked-by: Ricardo Ribalda Delgado <ricardo.ribalda@gmail.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Patch a9e93e8 has erroneously removed some comments which are
important to understand why the bus frequency is multiplied by
two during the spi transfer.
Reword the previous comment to a more appropriate message.
Suggested-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Andi Shyti <andi.shyti@samsung.com>
Reviewed-by: Michael Turquette <mturquette@baylibre.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
The new compatible is related to the Samsung Exynos5433 SoC. The
difference between the previous is that in the exynos5433 the SPI
controller is driven by three clocks instead of only one.
The new clock (ioclk) is controlling the input/output clock
whenever the controller is slave or master.
The presence of the clock line is detected from the compatibility
structure (exynos5433_spi_port_config) as a boolean value.
The probe function checks whether the ioclk is present and if so,
it acquires.
The runtime suspend and resume functions will handle the clock
enabling and disabling as well.
Signed-off-by: Andi Shyti <andi.shyti@samsung.com>
Reviewed-by: Michael Turquette <mturquette@baylibre.com>
Reviewed-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
If clk_prepare_enable() fails do not return -EBUSY but use the
value provided by the function itself.
Suggested-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Andi Shyti <andi.shyti@samsung.com>
Reviewed-by: Michael Turquette <mturquette@baylibre.com>
Reviewed-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
The goto labels of the style of
err4:
err3:
err2:
err1:
are complex to insert in between new errors without renaming all
the goto statements. Replace the errX naming style to meaningful
names in order to make it easier to insert new goto exit points.
Signed-off-by: Andi Shyti <andi.shyti@samsung.com>
Reviewed-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Reviewed-by: Michael Turquette <mturquette@baylibre.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Once a spi_master_get() call succeeds, we need an additional
spi_master_put() call to free the memory, otherwise we will
leak a reference to master. Fix by removing the unnecessary
spi_master_get() call.
Signed-off-by: Wei Yongjun <yongjun_wei@trendmicro.com.cn>
Reviewed-by: Andi Shyti <andi.shyti@samsung.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Due to the newly upstreamed 'critical clocks' API we can now
safely handle clocking in the SPI and I2C drivers without fear
of catastrophically crippling the running platform.
Signed-off-by: Lee Jones <lee.jones@linaro.org>
|
|
The workqueue has a single workitem(&ss->ws) and hence doesn't require
ordering. Also, it is not being used on a memory reclaim path. Hence, the
singlethreaded workqueue has been replaced with the use of system_wq.
System workqueues have been able to handle high level of concurrency
for a long time now and hence it's not required to have a singlethreaded
workqueue just to gain concurrency. Unlike a dedicated per-cpu workqueue
created with create_singlethread_workqueue(), system_wq allows multiple
work items to overlap executions even on the same CPU; however, a
per-cpu workqueue doesn't have any CPU locality or global ordering
guarantee unless the target CPU is explicitly specified and thus the
increase of local concurrency shouldn't make any difference.
Work item has been flushed in spi_sh_remove() to ensure that
there are no pending tasks while disconnecting the driver.
Signed-off-by: Bhaktipriya Shridhar <bhaktipriya96@gmail.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
The workqueue "wk" serves as a queue for carrying out execution
of requests. It has a single work item(&drv_data->work) and hence doesn't
require ordering. Also, it is not being used on a memory reclaim path.
Hence, the singlethreaded workqueue has been replaced with the use of
system_wq.
System workqueues have been able to handle high level of concurrency
for a long time now and hence it's not required to have a singlethreaded
workqueue just to gain concurrency. Unlike a dedicated per-cpu workqueue
created with create_singlethread_workqueue(), system_wq allows multiple
work items to overlap executions even on the same CPU; however, a
per-cpu workqueue doesn't have any CPU locality or global ordering
guarantee unless the target CPU is explicitly specified and thus the
increase of local concurrency shouldn't make any difference.
Work item has been flushed in pch_spi_free_resources() to ensure that
there are no pending tasks while disconnecting the driver.
Also dropped the label 'err_return' since it's not being used anymore.
Signed-off-by: Bhaktipriya Shridhar <bhaktipriya96@gmail.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
This patch adds supports for SPI device enumeration and removal via
ACPI reconfiguration notifications that are send as a result of an
ACPI table load or unload operation.
The code is very similar with the device tree reconfiguration code
with only small differences in the way we test and set the enumerated
state of the device:
* the equivalent of device tree's OF_POPULATED flag is the
flags.visited field in the ACPI device and the following wrappers
are used to manipulate it: acpi_device_enumerated(),
acpi_device_set_enumerated() and acpi_device_clear_enumerated()
* the device tree code checks of status of the OF_POPULATED flag to
avoid trying to create duplicate Linux devices in two places: once
when the controller is probed, and once when the reconfigure event
is received; in the ACPI code the check is performed only once when
the ACPI namespace is searched because this code path is invoked in
both of the two mentioned cases
The rest of the enumeration handling is similar with device tree: when
the Linux device is unregistered the ACPI device is marked as not
enumerated; also, when a device remove notification is received we
check that the device is in the enumerated state before continuing
with the removal of the Linux device.
Signed-off-by: Octavian Purdila <octavian.purdila@intel.com>
Reviewed-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Acked-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
Currently, the driver handles mapping buffers to be used by the DMA.
However, there are times that the current mapping implementation will
fail for certain buffers. Fortunately, the SPI framework can detect
and map buffers so its usable by the DMA.
Update the driver to utilize the SPI framework for buffer
mapping instead. Also incorporate hooks that the framework uses to
determine if the DMA can or can not be used.
This will result in the original omap2_mcspi_transfer_one function being
deleted and omap2_mcspi_work_one being renamed to
omap2_mcspi_transfer_one. Previously transfer_one was only responsible
for mapping and work_one handled the transfer. But now only transferring
needs to be handled by the driver.
Signed-off-by: Franklin S Cooper Jr <fcooper@ti.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
The function sg_split will be used by spi-omap2-mcspi to handle a SoC
workaround in the SPI driver. Therefore, select SG_SPLIT so this function
is available to the driver.
Signed-off-by: Franklin S Cooper Jr <fcooper@ti.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
The commit 30f3a6ab44d8 ("spi: pxa2xx: Add support for both chip selects on
Intel Braswell") introduces a support of chipselects for Intel Braswell SPI
host controller. Though it missed to convert the PCI part of the driver.
Do conversion here which enables both chipselects on Intel Braswell when
enumerated via PCI.
We don't care about num_chipselect value since it is overrided inside core
driver.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
It seems the commit e5262d0568dc ("spi: spi-pxa2xx: SPI support for Intel Quark
X1000") misses one place to be adapted for Intel Quark, i.e. in reset_sccr1().
Clear all RFT bits when call reset_sccr1() on Intel Quark.
Fixes: e5262d0568dc ("spi: spi-pxa2xx: SPI support for Intel Quark X1000")
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Cc: stable@vger.kernel.org
|
|
This is a complex patch for refactoring CLPS711X SPI driver.
This change adds devicetree support and removes board support.
Signed-off-by: Alexander Shiyan <shc_work@mail.ru>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
When the clock is coming from the cmu it is not required to be
disabled and then re-enabled in order to change the rate.
Besides, some exynos chipsets (e.g. exynos5433) do not deliver
any to the SFR if one from the pclk ("spi" in this case) or sclk
("busclk") is disabled.
Remove the clock disabling/enabling to avoid falling into this
situation.
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Andi Shyti <andi.shyti@samsung.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
OMAP35x and OMAP37x mentions in the McSPI End-of-Transfer Sequences section
that if the McSPI is configured as a Master and only DMA RX is being
performed then the DMA transfer size needs to be reduced by 1 or 2.
This was originally implemented by:
commit 57c5c28dbc83 ("spi: omap2_mcspi rxdma bugfix")
This patch adds comments to clarify what is going on in the code since its
not obvious what problem its addressing.
Signed-off-by: Franklin S Cooper Jr <fcooper@ti.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Some IoT and maker software stacks are using spidev to perform raw access
to the SPI bus instead of relying existing drivers provided by the kernel.
They then implement their own "drivers" in userspace on top of the spidev
raw interface. This is far from being an ideal solution but we do not want
to prevent using mainline Linux in these devices.
Now, it turns out that Windows has similar SPI devices than spidev which
allow raw access on the SPI bus to userspace programs as described in the
link below:
https://msdn.microsoft.com/windows/hardware/drivers/spb/spi-tests-in-mitt
These SPI test devices are also meant to be used during development and
testing.
In order to allow usage of spidev for development and testing in Linux, add
those same ACPI IDs to the spidev driver (which is Linux counterpart of the
Windows SPI test devices), but complain loudly so that users know it is not
good idea to use it in production systems. Instead they should be using
proper drivers for peripherals connected to the SPI bus.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Simply sort header block alphabetically.
While here, sort devices by PCI ID and add a copyright line for Intel.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
pcim_iomap_table() can't fail when called after pcim_iomap_regions(). Moreover,
we already dereference returned value and kernel will crash if it is not
correct.
Remove obvious leftover of commit 0202775bc3a2 ("spi/pxa2xx-pci: switch to use
pcim_* interfaces").
Cc: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
The SPI controllers used on Intel Merrifield are PXA2XX compatible. This patch
enables them.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Move LPSS specific setup to a separate function. It makes ->probe() cleaner as
well as allows extend the driver for different variation of hardware in the
future, e.g. for Intel Merrifield.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Kaby Lake PCH-H has the same SPI host controller as Skylake. Add these new
PCI IDs to the list of supported devices.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
It generates a static checker warning if an if statement isn't indented.
I think the code is fine except for the white space issue.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
The workqueue "workqueue" serves as a driver message queue.
It has a single work item(&drv_data->pump_messages) and hence doesn't
require ordering. Also, it is not being used on a memory reclaim path.
Hence, the singlethreaded workqueue has been replaced with the use of
system_wq.
System workqueues have been able to handle high level of concurrency
for a long time now and hence it's not required to have a singlethreaded
workqueue just to gain concurrency. Unlike a dedicated per-cpu workqueue
created with create_singlethread_workqueue(), system_wq allows multiple
work items to overlap executions even on the same CPU; however, a
per-cpu workqueue doesn't have any CPU locality or global ordering
guarantee unless the target CPU is explicitly specified and thus the
increase of local concurrency shouldn't make any difference.
Work item has been flushed in bfin_sport_spi_destroy_queue() to ensure
that there are no pending tasks while disconnecting the driver.
Signed-off-by: Bhaktipriya Shridhar <bhaktipriya96@gmail.com>
Acked-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
The workqueue "workqueue" has a single work item(&mps->work)
doesn't require ordering. Also, it is not being used on a memory reclaim
path. Hence, the singlethreaded workqueue has been replaced with the use
of system_wq.
System workqueues have been able to handle high level of concurrency
for a long time now and hence it's not required to have a singlethreaded
workqueue just to gain concurrency. Unlike a dedicated per-cpu workqueue
created with create_singlethread_workqueue(), system_wq allows multiple
work items to overlap executions even on the same CPU; however, a
per-cpu workqueue doesn't have any CPU locality or global ordering
guarantee unless the target CPU is explicitly specified and thus the
increase of local concurrency shouldn't make any difference.
Work item has been flushed in mpc52xx_psc_spi_of_remove() to ensure that
nothing is pending while disconnecting the driver.
Signed-off-by: Bhaktipriya Shridhar <bhaktipriya96@gmail.com>
Acked-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
The workqueue "workqueue" has a single work item(&c->work) and hence
doesn't require ordering. Also, it is not being used on a memory reclaim
path. Hence, the singlethreaded workqueue has been replaced with the use of
system_wq.
System workqueues have been able to handle high level of concurrency
for a long time now and hence it's not required to have a singlethreaded
workqueue just to gain concurrency. Unlike a dedicated per-cpu workqueue
created with create_singlethread_workqueue(), system_wq allows multiple
work items to overlap executions even on the same CPU; however, a
per-cpu workqueue doesn't have any CPU locality or global ordering
guarantee unless the target CPU is explicitly specified and thus the
increase of local concurrency shouldn't make any difference.
Work item has been flushed in txx9spi_remove() to ensure that
nothing is pending while disconnecting the driver.
Signed-off-by: Bhaktipriya Shridhar <bhaktipriya96@gmail.com>
Acked-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
The workqueue "workqueue" serves as a driver message queue.
It has a single work item(&drv_data->pump_messages) and hence doesn't
require ordering. Also, it is not being used on a memory reclaim path.
Hence, the singlethreaded workqueue has been replaced with the use of
system_wq.
System workqueues have been able to handle high level of concurrency
for a long time now and hence it's not required to have a singlethreaded
workqueue just to gain concurrency. Unlike a dedicated per-cpu workqueue
created with create_singlethread_workqueue(), system_wq allows multiple
work items to overlap executions even on the same CPU; however, a
per-cpu workqueue doesn't have any CPU locality or global ordering
guarantee unless the target CPU is explicitly specified and thus the
increase of local concurrency shouldn't make any difference.
Work item has been flushed in bfin_spi_destroy_queue() to ensure that there
are no pending tasks while disconnecting the driver.
Signed-off-by: Bhaktipriya Shridhar <bhaktipriya96@gmail.com>
Acked-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
'spi/fix/sunxi' and 'spi/fix/ti-qspi' into spi-linus
|
|
The whole function is inside an 'if' statement
("!is_polling(sdd)").
Check the opposite of that statement at the beginning and exit,
this way we can have one level less of indentation.
Remove the goto paths as they are redundant.
Signed-off-by: Andi Shyti <andi.shyti@samsung.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
At the start of the transfer, the spi_config function is called
twice, the first time when the 3c64xx_spi_prepare_message is
called and the second time with the s3c64xx_spi_transfer_one,
both called from the spi framework.
Remove the first call at the prepare message because in that
point we don't have the imformation about "bit per word" and
frequency.
Signed-off-by: Andi Shyti <andi.shyti@samsung.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
When the CS line is not connected, it is not needed to enable or
disable the chip selection functionality from the s3c64xx
devices in order to perform a transfer.
Set the CS controller logically always enabled already during
initialization (by writing '0' in the S3C64XX_SPI_SLAVE_SEL
register) and never disable it.
Signed-off-by: Andi Shyti <andi.shyti@samsung.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
To enable/disable the CS line, the driver performs a writel in
the S3C64XX_SPI_SLAVE_SEL registers. Group the register's
configuration in a single function.
Signed-off-by: Andi Shyti <andi.shyti@samsung.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
trivial fix to spelling mistake in dev_err message
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
The speed limits are unset in the sun4i and sun6i SPI drivers.
The maximum speed of SPI master is used when maximum speed of SPI slave
is not specified. Also the __spi_validate function should check that
transfer speeds do not exceed the master limits.
The user manual for A10 and A31 specifies maximum
speed of the SPI clock as 100MHz and minimum as 3kHz.
Setting the SPI clock to out-of-spec values can lock up the SoC.
Signed-off-by: Michal Suchanek <hramrach@gmail.com>
--
v2:
new patch
v3:
fix constant style
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
trivial fix to spelling mistake in dev_dbg message
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
After probe time, the pointer to the sh_msiof_chipdata structure in the
sh_msiof_spi_priv structure is used only for checking the SPI master flags.
As these are also available in the spi_master structure, convert the
users to access those, and remove the pointer.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
In some rare cases I see the following 'task blocked' information. It
looks like the PIO transfer has some problems and never succeeds. Make
use of wait_for_completion_timeout(..) to detect this case and
return -ETIMEDOUT.
[ 240.246067] INFO: task hexdump:1660 blocked for more than 120 seconds.
[ 240.246089] Not tainted 4.1.17 0000001
[ 240.246099] "echo 0 > /proc/sys/kernel/hung_task_timeout_secs" disables this message.
[ 240.246109] hexdump D c0575548 0 1660 1 0x00000000
[ 240.246132] Backtrace:
[ 240.246166] [<c057524c>] (__schedule) from [<c0575a84>] (schedule+0x40/0xa4)
[ 240.246176] r10:00000000 r9:c07f1300 r8:c07b8408 r7:c0576518 r6:7fffffff r5:7fffffff
[ 240.246210] r4:ee972e7c
[ 240.246233] [<c0575a44>] (schedule) from [<c0578544>] (schedule_timeout+0x174/0x274)
[ 240.246254] [<c05783d0>] (schedule_timeout) from [<c0576518>] (wait_for_common+0xc0/0x164)
[ 240.246263] r10:00000000 r9:c07f1300 r8:00000002 r7:00000000 r6:7fffffff r5:ee972e78
[ 240.246294] r4:ee972e7c
[ 240.246314] [<c0576458>] (wait_for_common) from [<c05765dc>] (wait_for_completion+0x20/0x24)
[ 240.246324] r10:ee972e50 r8:00000001 r7:c3976200 r6:ee972c00 r5:ee972e50 r4:c2c87d28
[ 240.246367] [<c05765bc>] (wait_for_completion) from [<c03f6b04>] (spi_imx_transfer+0xe8/0x3cc)
[ 240.246393] [<c03f6a1c>] (spi_imx_transfer) from [<c03f50e4>] (spi_bitbang_transfer_one+0xb4/0x250)
[ 240.246403] r10:ee972e50 r8:00000001 r7:00000000 r6:c2c87da0 r5:00000000 r4:c2c87d28
[ 240.246443] [<c03f5030>] (spi_bitbang_transfer_one) from [<c03f36e8>] (__spi_pump_messages+0x36c/0x6b4)
[ 240.246452] r10:ee9e5010 r9:00000001 r8:ee9e5010 r7:00000000 r6:c2c87da0 r5:c2c87d6c
[ 240.246483] r4:ee972c00
[ 240.246503] [<c03f337c>] (__spi_pump_messages) from [<c03f3b68>] (__spi_sync+0x138/0x1e4)
[ 240.246512] r10:00000000 r9:00000000 r8:c03f25a8 r7:00000000 r6:ee972c00 r5:c3976200
[ 240.246542] r4:c2c87da0
[ 240.246562] [<c03f3a30>] (__spi_sync) from [<c03f3c50>] (spi_sync+0x1c/0x20)
[ 240.246571] r10:00040000 r9:00000000 r8:c3976200 r7:00000000 r6:ee973300 r5:c2c87da0
[ 240.246602] r4:ee973014
[ 240.246623] [<c03f3c34>] (spi_sync) from [<c03f0210>] (m25p80_read+0xf8/0x124)
[ 240.246641] [<c03f0118>] (m25p80_read) from [<c03f1528>] (spi_nor_read+0x64/0x80)
[ 240.246651] r10:00004000 r8:00004000 r7:00000000 r6:00040000 r5:00000000 r4:ee973014
[ 240.246698] [<c03f14c4>] (spi_nor_read) from [<c03cdcb4>] (mtd_read+0x98/0xcc)
[ 240.246708] r7:c2c87ea0 r6:ee973098 r5:00000000 r4:001c0000
[ 240.246740] [<c03cdc1c>] (mtd_read) from [<c03d300c>] (mtdchar_read+0xcc/0x204)
[ 240.246750] r9:ed424000 r8:00000000 r7:b495d018 r6:c2c87f78 r5:00000000 r4:00040000
[ 240.246793] [<c03d2f40>] (mtdchar_read) from [<c013b1c4>] (__vfs_read+0x3c/0xe0)
[ 240.246803] r10:00004000 r9:00000000 r8:c2c87f78 r7:b495d018 r6:c2c87f78 r5:c05c8104
[ 240.246833] r4:c32fe600
[ 240.246852] [<c013b188>] (__vfs_read) from [<c013befc>] (vfs_read+0x98/0x154)
[ 240.246861] r10:00000000 r8:00040000 r7:00004000 r6:c2c87f78 r5:b495d018 r4:c32fe600
[ 240.246899] [<c013be64>] (vfs_read) from [<c013c008>] (SyS_read+0x50/0x90)
[ 240.246908] r10:00000000 r8:00040000 r7:b495d018 r6:00004000 r5:c32fe601 r4:c32fe600
[ 240.246953] [<c013bfb8>] (SyS_read) from [<c000fa60>] (ret_fast_syscall+0x0/0x3c)
[ 240.246962] r9:c2c86000 r8:c000fc04 r7:00000003 r6:00004000 r5:00000000 r4:b495d018
Signed-off-by: Christian Gmeiner <christian.gmeiner@gmail.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
SPI core provides DMA mapping with scatterlists. Start using it instead
of own implementation in spi-pxa2xx. Major difference in addition to
bunch of removed boilerplate code is that SPI core does
mapping/unmapping for all transfers in a message before and after the
message sending where spi-pxa2xx did mapping/unmapping for each
transfers separately.
Signed-off-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
We will find more use for struct spi_master pointer in pump_transfers()
and code will be more readable if we access it using local pointer than
through the drv_data->master.
Signed-off-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
The SPI-driver no longer contains the conditions for various CPUs, so
"maybe_unused" attributes is no longer needed.
This patch removes these attributes.
Signed-off-by: Alexander Shiyan <shc_work@mail.ru>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
SPI mode can be obtained directly from spi-device, there is no
need to keep a copy.
Signed-off-by: Alexander Shiyan <shc_work@mail.ru>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Patch reuse existing "chip_select" and "cs_gpio(s)" fields from SPI core.
Signed-off-by: Alexander Shiyan <shc_work@mail.ru>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
