| Age | Commit message (Collapse) | Author |
|---|
|
libsas makes use of scsi_schedule_eh() but forgets to clear the
host_eh_scheduled flag in its error handling routine. Because of this,
the error handler thread never gets to sleep; it's constantly awake and
trying to run the error routine leading to console spew and inability to
run anything else (at least on a UP system). The fix is to clear the
flag as we splice the work queue.
Cc: stable@kernel.org
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
|
|
fixed the connection problem when the private iscsi ipv4 address is
provisioned on the interface.
Signed-off-by: Karen Xie <kxie@chelsio.com>
Reviewed-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
|
|
The nopout's reserved field was not being initialized to zero
before being reused. Stale CDB values from previous SCSI cmds
of the same BHS offset was the cause of the disconnection
initiated by the Lefthand target.
Signed-off-by: Eddie Wai <eddie.wai@broadcom.com>
Reviewed-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
|
|
Remove gl_skb from cxgbi_ddp_info as it is only used by cxgb3i.
Signed-off-by: Karen Xie <kxie@chelsio.com>
Reviewed-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
|
|
There is no need to set ulpmode on the tx skbs if no digest is enabled.
Signed-off-by: Karen Xie <kxie@chelsio.com>
Reviewed-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
|
|
memset arg64 to zero in the passthrough ioctls to avoid leaking contents
of kernel stack memory to userland via uninitialized padding fields
inserted by the compiler for alignment reasons.
Signed-off-by: Stephen M. Cameron <scameron@beardog.cce.hp.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
|
|
unknown
Signed-off-by: Stephen M. Cameron <scameron@beardog.cce.hp.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
|
|
hpsa_add_msa2xxx_enclosure_device()
Thanks to Scott Teel for noticing this.
Signed-off-by: Stephen M. Cameron <scameron@beardog.cce.hp.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
|
|
Signed-off-by: Stephen M. Cameron <scameron@beardog.cce.hp.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
|
|
Signed-off-by: Stephen M. Cameron <scameron@beardog.cce.hp.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
|
|
Signed-off-by: Stephen M. Cameron <scameron@beardog.cce.hp.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
|
|
Need to take the lock while accessing the register to check to
see if config table changes have taken effect.
Signed-off-by: Stephen M. Cameron <scameron@beardog.cce.hp.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
|
|
This is to prevent hpsa from resetting older boards
which the cciss driver may be controlling.
Signed-off-by: Stephen M. Cameron <scameron@beardog.cce.hp.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
|
|
This is to conserve memory in a memory-limited kdump scenario
Signed-off-by: Stephen M. Cameron <scameron@beardog.cce.hp.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
|
|
and use the doorbell reset method if available (which doesn't
lock up the controller if you properly save and restore all
the PCI registers that you're supposed to.)
Signed-off-by: Stephen M. Cameron <scameron@beardog.cce.hp.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
|
|
After a reset, we should first wait for the board to become "not ready",
and then wait for it to become "ready", instead of immediately
waiting for it to become "ready", and do this waiting *after*
restoring PCI config space registers. Also, only wait 10 secs
for board to become "not ready" after a reset (it should quickly
become not ready.)
Signed-off-by: Stephen M. Cameron <scameron@beardog.cce.hp.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
|
|
They are defined in hpsa_cmd.h
Signed-off-by: Stephen M. Cameron <scameron@beardog.cce.hp.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
|
|
Some low bits might have been set by the driver, causing
a message like this to come out:
[ 13.288062] ------------[ cut here ]------------
[ 13.293211] WARNING: at lib/dma-debug.c:803 check_unmap+0x1a1/0x654()
[ 13.300387] Hardware name: ProLiant DL180 G6
[ 13.305335] hpsa 0000:06:00.0: DMA-API: device driver tries to free
DMA memory it has not allocated [device address=0x000000007f81e001]
[size=640 bytes]
Signed-off-by: Stephen M. Cameron <scameron@beardog.cce.hp.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
|
|
Signed-off-by: Stephen M. Cameron <scameron@beardog.cce.hp.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
|
|
[jejb: fix up patch problems and checkpatch.pl issues]
Signed-off-by: Nick Cheng <nick.cheng@areca.com.tw>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
|
|
Currently NetApp's VID/PID details in the INQUIRY response shows up as
'NETAPP' and 'LUN'. With upcoming scalable SAN ONTAP version on NetApp
controllers, the PID entry alone is being modified to 'LUN C-Mode' (to
distinguish current ONTAP LUNs from scalable ONTAP LUNs).
'LUN' would still suffice for matching 'LUN C-Mode' but best to
explicitly add these new NetApp LUNs to the device list.
Reported-by: Martin George <marting@netapp.com>
Acked-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
|
|
Adds Promise VTrak devices to the ALUA device handler.
Signed-off-by: Ilgu Hong <ilgu.hong@promise.com>
Signed-off-by: Joseph Gruher <joseph.r.gruher@intel.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
|
|
Initialize stpg_endio() 'err' to SCSI_DH_OK and only change it to
SCSI_DH_IO accordingly. This allows the switching of target group state
to be properly reported when no error has occurred.
Signed-off-by: Joseph Gruher <joseph.r.gruher@intel.com>
Signed-off-by: Ilgu Hong <ilgu.hong@promise.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
|
|
The use of blk_execute_rq_nowait() implies __blk_put_request() is needed
in stpg_endio() rather than blk_put_request() -- blk_finish_request() is
called with queue lock already held.
Signed-off-by: Joseph Gruher <joseph.r.gruher@intel.com>
Signed-off-by: Ilgu Hong <ilgu.hong@promise.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Cc: stable@kernel.org
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
|
|
submit_stpg() will always return failure so alua_activate() will report
failure via dm-multipath callback function. Even though the stpg fired
successfuly dm-multipath does not know and always fails to change the
valid path.
By returning SCSI_DH_OK we're now skipping alua_activate()'s call to
activate_complete 'fn'. But this is fine because stpg_endio() will call
it via h->callback_fn().
Signed-off-by: Joseph Gruher <joseph.r.gruher@intel.com>
Signed-off-by: Ilgu Hong <ilgu.hong@promise.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
|
|
Upgrade driver version from 7.100.00.00 to 8.100.00.00
Signed-off-by: Kashyap Desai <kashyap.desai@lsi.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
|
|
Basic Code Cleanup:
(1) _base_get_cb_idx and mpt2sas_base_free_smid were reorganized in
similar fashion so the order of obtaining the cbx and smid are
scsiio,
hi_priority, and internal.
(2) The hi_priority and internal request queue struct was made
smaller
by removing the scmd and chain_tracker, thus saving memory
allocation.
(3) For scsiio request, a new structure was created having the same
elements from the former request tracker struct.
Signed-off-by: Kashyap Desai <kashyap.desai@lsi.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
|
|
Add support for Customer specific branding messages when device driver loads,
based on specific customer subsystem vendor and device Ids
Signed-off-by: Kashyap Desai <kashyap.desai@lsi.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
|
|
Revision P MPI Header Update:
a) Added enable/disable SATA NCQ operations to SAS IO Unit Control
Request.
b) Modified Host Based Discovery Action Request message format.
c) Removed Device Path bit from IO Unit Page 1 Flags field.
d) Added description of ChainOffset field for Diagnostic Data Upload
Tool.Chaining is not allowed.
Removed mpi2_history.txt file
Signed-off-by: Kashyap Desai <kashyap.desai@lsi.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
|
|
Issue:
IR shutdown(sending) and IR shutdown(complete) messages not
listed in /var/log/messages when driver is removed.
The driver needs to issue a MPI2_RAID_ACTION_SYSTEM_SHUTDOWN_INITIATED
request when the driver is unloaded so the IR metadata journal is updated.
If this request is not sent, then the volume would need a "check
consistency" issued on the next bootup if the volume was roamed from one
initiator to another. The current driver supports this feature only when the
system is rebooted, however this also need to be supported if the driver is
unloaded
Fix:
To fix this issue, the driver is going
to need to call the _scsih_ir_shutdown prior to reporting
the volumes missing from the OS, hence the device handles
are still present.
Signed-off-by: Kashyap Desai <kashyap.desai@lsi.com>
Cc: stable@kernel.org
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
|
|
There was a configuration page timing out during the initial port
enable at driver load time. The port enable would fail, and this would
result in the driver unloading itself, meanwhile the driver was accessing
freed memory in another context resulting in the panic. The fix is to
prevent access to freed memory once the driver had issued the diag reset
which woke up the sleeping port enable process. The routine
_base_reset_handler was reorganized so the last sleeping process woken up was
the port_enable.
Signed-off-by: Kashyap Desai <kashyap.desai@lsi.com>
Cc: stable@kernel.org
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
|
|
completion
False timeout after hard resets, there were two issues which leads
to timeout.
(1) Panic because of invalid memory access in the broadcast asyn
event processing routine due to a race between accessing the scsi command
pointer from broadcast asyn event processing thread and completing
the same scsi command from the interrupt context.
(2) Broadcast asyn event notifcations are not handled due to events
ignored while the broadcast asyn event is activity being processed
from the event process kernel thread.
In addition, changed the ABRT_TASK_SET to ABORT_TASK in the
broadcast async event processing routine. This is less disruptive to other
request that generate Broadcast Asyn Primitives besides target
reset. e.g clear reservations, microcode download,and mode select.
Signed-off-by: Kashyap Desai <kashyap.desai@lsi.com>
Cc: stable@kernel.org
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
|
|
The ioc->hba_queue_depth is not properly resized when the controller
firmware reports that it supports more outstanding IO than what can be fit
inside the reply descriptor pool depth. This is reproduced by setting the
controller global credits larger than 30,000. The bug results in an
incorrect sizing of the queues. The fix is to resize the queue_size by
dividing queue_diff by two.
Signed-off-by: Kashyap Desai <kashyap.desai@lsi.com>
Cc: stable@kernel.org
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
|
|
The "internal device reset complete" event is not supported
for older firmware prior to MPI Rev K We added
a check in the driver so the "internal device reset" event is
ignored for older firmware. When ignored, the tm_busy flag doesn't
get set nor cleared. Without this fix, IO queues would be froozen
indefinetly after the "internal device reset" event, as the "complete" event
never sent to clear the flag.
Signed-off-by: Kashyap Desai <kashyap.desai@lsi.com>
Cc: stable@kernel.org
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
|
|
When zoning end devices, the driver is not sending device
removal handshake alogrithm to firmware. This results in controller
firmware not sending sas topology add events the next time the device is
added. The fix is the driver should be doing the device removal handshake
even though the PHYSTATUS_VACANT bit is set in the PhyStatus of the
event data. The current design is avoiding the handshake when the
VACANT bit is set in the phy status.
Signed-off-by: Kashyap Desai <kashyap.desai@lsi.com>
Cc: stable@kernel.org
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
|
|
Signed-off-by: Justin P. Mattock <justinmattock@gmail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
|
|
values
The [vk][cmz]alloc(_node) family of functions return void pointers which
it's completely unnecessary/pointless to cast to other pointer types since
that happens implicitly.
This patch removes such casts from drivers/scsi/
Signed-off-by: Jesper Juhl <jj@chaosbits.net>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
|
|
* git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi-post-merge-2.6:
[SCSI] target: Add LIO target core v4.0.0-rc6
[SCSI] sd,sr: kill compat SDEV_MEDIA_CHANGE event
[SCSI] sd: implement sd_check_events()
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/jbarnes/pci-2.6
* 'linux-next' of git://git.kernel.org/pub/scm/linux/kernel/git/jbarnes/pci-2.6:
PCI/PM: Report wakeup events before resuming devices
PCI/PM: Use pm_wakeup_event() directly for reporting wakeup events
PCI: sysfs: Update ROM to include default owner write access
x86/PCI: make Broadcom CNB20LE driver EMBEDDED and EXPERIMENTAL
x86/PCI: don't use native Broadcom CNB20LE driver when ACPI is available
PCI/ACPI: Request _OSC control once for each root bridge (v3)
PCI: enable pci=bfsort by default on future Dell systems
PCI/PCIe: Clear Root PME Status bits early during system resume
PCI: pci-stub: ignore zero-length id parameters
x86/PCI: irq and pci_ids patch for Intel Patsburg
PCI: Skip id checking if no id is passed
PCI: fix __pci_device_probe kernel-doc warning
PCI: make pci_restore_state return void
PCI: Disable ASPM if BIOS asks us to
PCI: Add mask bit definition for MSI-X table
PCI: MSI: Move MSI-X entry definition to pci_regs.h
Fix up trivial conflicts in drivers/net/{skge.c,sky2.c} that had in the
meantime been converted to not use legacy PCI power management, and thus
no longer use pci_restore_state() at all (and that caused trivial
conflicts with the "make pci_restore_state return void" patch)
|
|
SDEV_MEDIA_CHANGE event was first added by commit a341cd0f (SCSI: add
asynchronous event notification API) for SATA AN support and then
extended to cover generic media change events by commit 285e9670
([SCSI] sr,sd: send media state change modification events).
This event was mapped to block device in userland with all properties
stripped to simulate CHANGE event on the block device, which, in turn,
was used to trigger further userspace action on media change.
The recent addition of disk event framework kept this event for
backward compatibility but it turns out to be unnecessary and causes
erratic and inefficient behavior. The new disk event generates proper
events on the block devices and the compat events are mapped to block
device with all properties stripped, so the block device ends up
generating multiple duplicate events for single actual event.
This patch removes the compat event generation from both sr and sd as
suggested by Kay Sievers. Both existing and newer versions of udev
and the associated tools will behave better with the removal of these
events as they from the beginning were expecting events on the block
devices.
Signed-off-by: Tejun Heo <tj@kernel.org>
Acked-by: Kay Sievers <kay.sievers@vrfy.org>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
|
|
Replace sd_media_change() with sd_check_events().
* Move media removed logic into set_media_not_present() and
media_not_present() and set sdev->changed iff an existing media is
removed or the device indicates UNIT_ATTENTION.
* Make sd_check_events() sets sdev->changed if previously missing
media becomes present.
* Event is reported only if sdev->changed is set.
This makes media presence event reported if scsi_disk->media_present
actually changed or the device indicated UNIT_ATTENTION. For backward
compatibility, SDEV_EVT_MEDIA_CHANGE is generated each time
sd_check_events() detects media change event.
[jejb: fix boot failure]
Signed-off-by: Tejun Heo <tj@kernel.org>
Acked-by: Jens Axboe <jaxboe@fusionio.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
|
|
* 'for-2.6.38/core' of git://git.kernel.dk/linux-2.6-block: (43 commits)
block: ensure that completion error gets properly traced
blktrace: add missing probe argument to block_bio_complete
block cfq: don't use atomic_t for cfq_group
block cfq: don't use atomic_t for cfq_queue
block: trace event block fix unassigned field
block: add internal hd part table references
block: fix accounting bug on cross partition merges
kref: add kref_test_and_get
bio-integrity: mark kintegrityd_wq highpri and CPU intensive
block: make kblockd_workqueue smarter
Revert "sd: implement sd_check_events()"
block: Clean up exit_io_context() source code.
Fix compile warnings due to missing removal of a 'ret' variable
fs/block: type signature of major_to_index(int) to major_to_index(unsigned)
block: convert !IS_ERR(p) && p to !IS_ERR_NOR_NULL(p)
cfq-iosched: don't check cfqg in choose_service_tree()
fs/splice: Pull buf->ops->confirm() from splice_from_pipe actors
cdrom: export cdrom_check_events()
sd: implement sd_check_events()
sr: implement sr_check_events()
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/jikos/trivial
* 'for-next' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/trivial: (43 commits)
Documentation/trace/events.txt: Remove obsolete sched_signal_send.
writeback: fix global_dirty_limits comment runtime -> real-time
ppc: fix comment typo singal -> signal
drivers: fix comment typo diable -> disable.
m68k: fix comment typo diable -> disable.
wireless: comment typo fix diable -> disable.
media: comment typo fix diable -> disable.
remove doc for obsolete dynamic-printk kernel-parameter
remove extraneous 'is' from Documentation/iostats.txt
Fix spelling milisec -> ms in snd_ps3 module parameter description
Fix spelling mistakes in comments
Revert conflicting V4L changes
i7core_edac: fix typos in comments
mm/rmap.c: fix comment
sound, ca0106: Fix assignment to 'channel'.
hrtimer: fix a typo in comment
init/Kconfig: fix typo
anon_inodes: fix wrong function name in comment
fix comment typos concerning "consistent"
poll: fix a typo in comment
...
Fix up trivial conflicts in:
- drivers/net/wireless/iwlwifi/iwl-core.c (moved to iwl-legacy.c)
- fs/ext4/ext4.h
Also fix missed 'diabled' typo in drivers/net/bnx2x/bnx2x.h while at it.
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/jgarzik/libata-dev
* 'upstream-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jgarzik/libata-dev:
pata_platform: Remove CONFIG_HAVE_PATA_PLATFORM's dependencies.
pata_hpt37x: actually limit HPT370 to UltraDMA/66
pata_hpt3x2n: coding style cleanup
pata_hpt37x: coding style cleanup
pata_hpt366: coding style cleanup
pata_hpt3x2n: calculate average f_CNT
pata_hpt3x2n: clarify about HPT371N support
pata_hpt{37x|3x2n}: SATA mode filtering
[libata] avoid needlessly passing around ptr to SCSI completion func
[libata] new driver acard_ahci, for ATP8620 host controller
|
|
* git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi-misc-2.6: (147 commits)
[SCSI] arcmsr: fix write to device check
[SCSI] lpfc: lower stack use in lpfc_fc_frame_check
[SCSI] eliminate an unnecessary local variable from scsi_remove_target()
[SCSI] libiscsi: use bh locking instead of irq with session lock
[SCSI] libiscsi: do not take host lock in queuecommand
[SCSI] be2iscsi: fix null ptr when accessing task hdr
[SCSI] be2iscsi: fix gfp use in alloc_pdu
[SCSI] libiscsi: add more informative failure message during iscsi scsi eh
[SCSI] gdth: Add missing call to gdth_ioctl_free
[SCSI] bfa: remove unused defintions and misc cleanups
[SCSI] bfa: remove inactive functions
[SCSI] bfa: replace bfa_assert with WARN_ON
[SCSI] qla2xxx: Use sg_next to fetch next sg element while walking sg list.
[SCSI] qla2xxx: Fix to avoid recursive lock failure during BSG timeout.
[SCSI] qla2xxx: Remove code to not reset ISP82xx on failure.
[SCSI] qla2xxx: Display mailbox register 4 during 8012 AEN for ISP82XX parts.
[SCSI] qla2xxx: Don't perform a BIG_HAMMER if Get-ID (0x20) mailbox command fails on CNAs.
[SCSI] qla2xxx: Remove redundant module parameter permission bits
[SCSI] qla2xxx: Add sysfs node for displaying board temperature.
[SCSI] qla2xxx: Code cleanup to remove unwanted comments and code.
...
|
|
It's stored in struct scsi_cmnd->scsi_done, making several 'done'
parameters to functions redundant.
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
|
|
Use command->sc_data_direction instead of trying (incorrectly) to
figure it out from the command itself
[jejb: fix up compile failure]
Signed-off-by: Roel Kluin <roel.kluin@gmail.com>
Acked-by: NickCheng <nick.cheng@areca.com.tw>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
|
|
according to checkstack the lpfc_fc_frame_check occupies the first
place in stack usage:
make checkstack
objdump -d vmlinux $(find . -name '*.ko') | \
perl /root/rpmbuild/BUILD/kernel-2.6.32/linux-2.6.32.x86_64/scripts/checkstack.pl x86_64
0x000013f4 lpfc_fc_frame_check [lpfc]: 1936
...
This change makes the rctl_names static, thus not on stack.
Signed-off-by: Tomas Henzl <thenzl@redhat.com>
Acked-by: James Smart <james.smart@emulex.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
|
|
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
|
|
The below patch fixes a typo "diable" to "disable" and also fixes another typo in a comment.
Please let me know if this is correct or not.
Signed-off-by: Justin P. Mattock <justinmattock@gmail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
|
