summaryrefslogtreecommitdiff
path: root/drivers/scsi
AgeCommit message (Collapse)Author
2017-02-13scsi: megaraid_sas: enhance debug logs in OCR contextShivasharan S
Add additional logging from driver in OCR context. Add debug logs for partial completion of IOs is iodone context. Signed-off-by: Shivasharan S <shivasharan.srikanteshwara@broadcom.com> Signed-off-by: Kashyap Desai <kashyap.desai@broadcom.com> Reviewed-by: Hannes Reinecke <hare@suse.com> Reviewed-by: Tomas Henzl <thenzl@redhat.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
2017-02-13scsi: megaraid_sas: set residual bytes count during IO completionShivasharan S
Fixing issue of not setting residual bytes correctly. Signed-off-by: Shivasharan S <shivasharan.srikanteshwara@broadcom.com> Signed-off-by: Kashyap Desai <kashyap.desai@broadcom.com> Reviewed-by: Hannes Reinecke <hare@suse.com> Reviewed-by: Tomas Henzl <thenzl@redhat.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
2017-02-13scsi: megaraid_sas: raid 1 write performance for large ioShivasharan S
Avoid Host side PCI bandwidth bottleneck and hint FW to do Write buffering using RaidFlag MR_RAID_FLAGS_IO_SUB_TYPE_LDIO_BW_LIMIT. Once IO is landed in FW with MR_RAID_FLAGS_IO_SUB_TYPE_LDIO_BW_LIMIT, it will do single DMA from host and buffer the Write operation. On back end, FW will DMA same buffer to the Mirror and Data Arm. This will improve large block IO performance which bottleneck due to Host side PCI bandwidth limitation. Consistent ~4000MB T.P for 256K Block size is expected performance numbers. IOPS for small Block size should be on par with Disk performance. (E.g 42 SAS Disk in JBOD mode gives 3700MB T.P. Same Drive used in R1 WT mode, should give ~1800MB T.P) Using this patch 24 R1 VDs (HDD) gives below performance for Sequential Write. Without this patch, we cannot reach above 3200MB (Throughput is in MB.) Block Size 50% 256K and 50% 4K 100% 256K 4K 3100 2030 8K 3140 2740 16K 3140 3140 32K 3400 3240 64K 3500 3700 128K 3870 3870 256K 3920 3920 Signed-off-by: Shivasharan S <shivasharan.srikanteshwara@broadcom.com> Signed-off-by: Kashyap Desai <kashyap.desai@broadcom.com> Reviewed-by: Hannes Reinecke <hare@suse.com> Reviewed-by: Tomas Henzl <thenzl@redhat.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
2017-02-13scsi: megaraid_sas: NVME fast path io supportShivasharan S
This patch provide true fast path IO support. Driver creates PRP for NVME drives and send Fast Path for performance. Certain h/w requirement needs to be taken care in driver. Signed-off-by: Shivasharan S <shivasharan.srikanteshwara@broadcom.com> Signed-off-by: Kashyap Desai <kashyap.desai@broadcom.com> Reviewed-by: Hannes Reinecke <hare@suse.com> Reviewed-by: Tomas Henzl <thenzl@redhat.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
2017-02-13scsi: megaraid_sas: NVME interface target prop addedShivasharan S
This patch fetch true values of NVME property from FW using New DCMD interface MR_DCMD_DEV_GET_TARGET_PROP Signed-off-by: Shivasharan S <shivasharan.srikanteshwara@broadcom.com> Signed-off-by: Kashyap Desai <kashyap.desai@broadcom.com> Reviewed-by: Hannes Reinecke <hare@suse.com> Reviewed-by: Tomas Henzl <thenzl@redhat.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
2017-02-13scsi: megaraid_sas: NVME Interface detection and prop settingsShivasharan S
Adding detection logic for NVME device attached behind Ventura controller. Driver set HostPageSize in IOC_INIT frame to inform about page size for NVME devices. Firmware reports NVME page size to the driver. PD INFO DCMD provide new interface type NVME_PD. Driver set property of NVME device. Signed-off-by: Shivasharan S <shivasharan.srikanteshwara@broadcom.com> Signed-off-by: Kashyap Desai <kashyap.desai@broadcom.com> Reviewed-by: Hannes Reinecke <hare@suse.com> Reviewed-by: Tomas Henzl <thenzl@redhat.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
2017-02-13scsi: megaraid_sas: change issue_dcmd to return void from intShivasharan S
With the changes to remove checks for a valid request descriptor, issue_dcmd will now always return DCMD_SUCCESS. This patch changes return type of issue_dcmd to void and change all callers appropriately. Signed-off-by: Shivasharan S <shivasharan.srikanteshwara@broadcom.com> Signed-off-by: Kashyap Desai <kashyap.desai@broadcom.com> Reviewed-by: Hannes Reinecke <hare@suse.com> Reviewed-by: Tomas Henzl <thenzl@redhat.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
2017-02-13scsi: megaraid_sas: megasas_get_request_descriptor always return valid descShivasharan S
No functional change. Code clean up. Removing error code which is not valid scenario. In megasas_get_request_descriptor we can remove the error handling which is not required. With fusion controllers, if there is a valid message frame available, we are guaranteed to get a corresponding request descriptor. Signed-off-by: Shivasharan S <shivasharan.srikanteshwara@broadcom.com> Signed-off-by: Kashyap Desai <kashyap.desai@broadcom.com> Reviewed-by: Hannes Reinecke <hare@suse.com> Reviewed-by: Tomas Henzl <thenzl@redhat.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
2017-02-13scsi: megaraid_sas: Use DID_REQUEUEShivasharan S
Moving to use DID_REQUEUE return type for reliable unconditional retries. Driver wants unconditional re-queue, so replace DID_RESET with DID_REQUEUE Discussed below - https://www.spinics.net/lists/linux-scsi/msg102848.html Signed-off-by: Shivasharan S <shivasharan.srikanteshwara@broadcom.com> Signed-off-by: Kashyap Desai <kashyap.desai@broadcom.com> Reviewed-by: Hannes Reinecke <hare@suse.com> Reviewed-by: Tomas Henzl <thenzl@redhat.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
2017-02-13scsi: megaraid_sas: RAID map is accessed for SYS PDs when use_seqnum_jbod_fp ↵Shivasharan S
is not set Signed-off-by: Shivasharan S <shivasharan.srikanteshwara@broadcom.com> Signed-off-by: Kashyap Desai <kashyap.desai@broadcom.com> Reviewed-by: Hannes Reinecke <hare@suse.com> Reviewed-by: Tomas Henzl <thenzl@redhat.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
2017-02-13scsi: megaraid_sas: Refactor MEGASAS_IS_LOGICAL macro using sdevShivasharan S
Signed-off-by: Shivasharan S <shivasharan.srikanteshwara@broadcom.com> Signed-off-by: Kashyap Desai <kashyap.desai@broadcom.com> Reviewed-by: Hannes Reinecke <hare@suse.com> Reviewed-by: Tomas Henzl <thenzl@redhat.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
2017-02-13scsi: megaraid_sas: 32 bit descriptor fire cmd optimizationShivasharan S
No functional change. Code refactor. megasas_fire_cmd_fusion can always use 32 bit descriptor write for ventura. No need to pass extra flag. Only IOC INIT required 64 bit Descriptor write. Signed-off-by: Shivasharan S <shivasharan.srikanteshwara@broadcom.com> Signed-off-by: Kashyap Desai <kashyap.desai@broadcom.com> Reviewed-by: Tomas Henzl <thenzl@redhat.com> Reviewed-by: Hannes Reinecke <hare@suse.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
2017-02-13scsi: megaraid_sas: raid 1 fast path code optimizeShivasharan S
No functional change. Code refactor. Remove function megasas_fpio_to_ldio as we never require to convert fpio to ldio because of frame unavailability. Grab extra frame of raid 1 write fast path before it creates first frame as Fast Path. Removed is_raid_1_fp_write flag as raid 1 write fast path command is decided using r1_alt_dev_handle only. Move resetting megasas_cmd_fusion fields at common function megasas_return_cmd_fusion. Signed-off-by: Shivasharan S <shivasharan.srikanteshwara@broadcom.com> Signed-off-by: Kashyap Desai <kashyap.desai@broadcom.com> Reviewed-by: Hannes Reinecke <hare@suse.com> Reviewed-by: Tomas Henzl <thenzl@redhat.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
2017-02-13scsi: megaraid_sas: cpu select rework.Shivasharan S
No functional change. Code refactor. Signed-off-by: Shivasharan S <shivasharan.srikanteshwara@broadcom.com> Signed-off-by: Kashyap Desai <kashyap.desai@broadcom.com> Reviewed-by: Hannes Reinecke <hare@suse.com> Reviewed-by: Tomas Henzl <thenzl@redhat.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
2017-02-13Revert "scsi: megaraid_sas: Enable or Disable Fast path based on the PCI ↵Shivasharan S
Threshold Bandwidth" This reverts commit "3e5eadb1a881" ("scsi: megaraid_sas: Enable or Disable Fast path based on the PCI Threshold Bandwidth") This patch was aimed to increase performance of R1 Write operation for large IO size. Since this method used timer approach, it turn on/off fast path did not work as expected. Patch 0013 describes new algorithm and performance number. Signed-off-by: Shivasharan S <shivasharan.srikanteshwara@broadcom.com> Signed-off-by: Kashyap Desai <kashyap.desai@broadcom.com> Reviewed-by: Hannes Reinecke <hare@suse.com> Reviewed-by: Tomas Henzl <thenzl@redhat.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
2017-02-11Merge tag 'scsi-fixes' of ↵Linus Torvalds
git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi Pull SCSI fixes from James Bottomley: "Six fairly small fixes. None is a real show stopper, two automation detected problems: one memory leak, one use after free and four others each of which fixes something that has been a significant source of annoyance to someone" * tag 'scsi-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi: scsi: zfcp: fix use-after-free by not tracing WKA port open/close on failed send scsi: aacraid: Fix INTx/MSI-x issue with older controllers scsi: mpt3sas: disable ASPM for MPI2 controllers scsi: mpt3sas: Force request partial completion alignment scsi: qla2xxx: Avoid that issuing a LIP triggers a kernel crash scsi: qla2xxx: Fix a recently introduced memory leak
2017-02-11Merge git://git.kernel.org/pub/scm/linux/kernel/git/davem/netDavid S. Miller
2017-02-09Merge remote-tracking branch 'mkp-scsi/4.10/scsi-fixes' into fixesJames Bottomley
2017-02-09scsi: aacraid: Fix INTx/MSI-x issue with older controllersDave Carroll
commit 78cbccd3bd68 ("aacraid: Fix for KDUMP driver hang") caused a problem on older controllers which do not support MSI-x (namely ASR3405,ASR3805). This patch conditionalizes the previous patch to controllers which support MSI-x Cc: <stable@vger.kernel.org> # v4.7+ Fixes: 78cbccd3bd68 ("aacraid: Fix for KDUMP driver hang") Reported-by: Arkadiusz Miskiewicz <a.miskiewicz@gmail.com> Signed-off-by: Dave Carroll <david.carroll@microsemi.com> Reviewed-by: Raghava Aditya Renukunta <RaghavaAditya.Renukunta@microsemi.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
2017-02-09scsi: mpt3sas: disable ASPM for MPI2 controllersojab
MPI2 controllers sometimes got lost (i.e. disappear from /sys/bus/pci/devices) if ASMP is enabled. Signed-off-by: Slava Kardakov <ojab@ojab.ru> Fixes: https://bugzilla.kernel.org/show_bug.cgi?id=60644 Cc: <stable@vger.kernel.org> Acked-by: Sreekanth Reddy <Sreekanth.Reddy@broadcom.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
2017-02-09scsi: qedi: Fix possible memory leak in qedi_iscsi_update_conn()Wei Yongjun
'conn_info' is malloced in qedi_iscsi_update_conn() and should be freed before leaving from the error handling cases, otherwise it will cause memory leak. Fixes: ace7f46ba5fd ("scsi: qedi: Add QLogic FastLinQ offload iSCSI driver framework.") Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com> Acked-by: Manish Rangankar <Manish.Rangankar@cavium.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
2017-02-09qla2xxx: Avoid using variable-length arraysBart Van Assche
This patch does not change any functionality but avoids that sparse complains about using variable-length arrays. Signed-off-by: Bart Van Assche <bart.vanassche@sandisk.com> Acked-by: Himanshu Madhani <himanshu.madhani@cavium.com> Cc: Quinn Tran <quinn.tran@cavium.com> Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
2017-02-09qla2xxx: Simplify usage of SRB structure in driverJoe Carnuccio
This patch simplifies SRB structure usage in driver. - Simplify sp->done() and sp->free() interfaces. - Remove sp->fcport->vha to use vha pointer from sp. - Use sp->vha context in qla2x00_rel_sp(). Signed-off-by: Joe Carnuccio <joe.carnuccio@cavium.com> Signed-off-by: Himanshu Madhani <himanshu.madhani@cavium.com> Signed-off-by: Bart Van Assche <bart.vanassche@sandisk.com> Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
2017-02-09qla2xxx: Improve RSCN handling in driverQuinn Tran
Current code blindly does State Change Registration when the link is up. Move SCR behind fabric scan, so that arbitrated loop scan would not get erroneous error message. Some of the other improvements are as follows - Add session deletion for TPRLO and send acknowledgment for TPRLO. - Enable FW option to move ABTS, RIDA & PUREX from RSPQ to ATIOQ. - Save NPort ID early in link init. - Move ABTS & RIDA to ATIOQ helps in keeping command ordering and link up sequence ordering. - Save Nport ID and update VP map so that SCSI CMD/ATIO won't be dropped. - fcport alloc does the initializes memory to zero. Remove memset to zero since It might corrupt link list. - Turn off Registration for State Change MB in loop mode. Signed-off-by: Quinn Tran <quinn.tran@cavium.com> Signed-off-by: Himanshu Madhani <himanshu.madhani@cavium.com> Signed-off-by: Bart Van Assche <bart.vanassche@sandisk.com> Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
2017-02-09qla2xxx: Remove unused reverse_ini_modeHimanshu Madhani
With support for dual mode in the driver, this mode becomes dead code. Remove reverse_ini_mode from code. Signed-off-by: Himanshu Madhani <himanshu.madhani@cavium.com> Signed-off-by: Bart Van Assche <bart.vanassche@sandisk.com> Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
2017-02-09qla2xxx: Add Dual mode support in the driverQuinn Tran
Add switch to allow both Initiator Mode & Target mode to operate at the same time. Signed-off-by: Quinn Tran <quinn.tran@cavium.com> Signed-off-by: Himanshu Madhani <himanshu.madhani@cavium.com> Signed-off-by: Bart Van Assche <bart.vanassche@sandisk.com> Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
2017-02-09qla2xxx: Add framework for async fabric discoveryQuinn Tran
Currently code performs a full scan of the fabric for every RSCN. Its an expensive process in a noisy large SAN. This patch optimizes expensive fabric discovery process by scanning switch for the affected port when RSCN is received. Currently Initiator Mode code makes login/logout decision without knowledge of target mode. This causes driver and firmware to go out-of-sync. This framework synchronizes both initiator mode personality and target mode personality in making login/logout decision. This patch adds following capabilities in the driver - Send Notification Acknowledgement asynchronously. - Update session/fcport state asynchronously. - Create a session or fcport struct asynchronously. - Send GNL asynchronously. The command will ask FW to provide a list of FC Port entries FW knows about. - Send GPDB asynchronously. The command will ask FW to provide detail data of an FC Port FW knows about or perform ADISC to verify the state of the session. - Send GPNID asynchronously. The command will ask switch to provide WWPN for provided NPort ID. - Send GPSC asynchronously. The command will ask switch to provide registered port speed for provided WWPN. - Send GIDPN asynchronously. The command will ask the switch to provide Nport ID for provided WWPN. - In driver unload path, schedule all session for deletion and wait for deletion to complete before allowing driver unload to proceed. Signed-off-by: Quinn Tran <quinn.tran@cavium.com> Signed-off-by: Himanshu Madhani <himanshu.madhani@cavium.com> [ bvanassche: fixed spelling in patch description ] Signed-off-by: Bart Van Assche <bart.vanassche@sandisk.com> Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
2017-02-08qla2xxx: Track I-T nexus as single fc_port structQuinn Tran
Current code merges qla_tgt_sess and fc_port structure into single fc_port structure representing same I-T nexus. Signed-off-by: Quinn Tran <quinn.tran@cavium.com> Signed-off-by: Himanshu Madhani <himanshu.madhani@cavium.com> [ bvanassche: fixed spelling of patch description ] Signed-off-by: Bart Van Assche <bart.vanassche@sandisk.com> Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
2017-02-08qla2xxx: Use d_id instead of s_id for more clarityQuinn Tran
Updated code with d_id from s_id for better readability and clarity. Signed-off-by: Quinn Tran <quinn.tran@cavium.com> Signed-off-by: Himanshu Madhani <himanshu.madhani@cavium.com> Reviewed-by: Christoph Hellwig <hch@lst.de> [ bvanassche: fixed spelling of patch description ] Signed-off-by: Bart Van Assche <bart.vanassche@sandisk.com> Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
2017-02-08qla2xxx: Fix wrong argument in sp done callbackQuinn Tran
Callback for sp->done expects scsi_qla_host is passed in as argument, Instead qla_hw_data is passed in. Signed-off-by: Quinn Tran <quinn.tran@cavium.com> Signed-off-by: Himanshu Madhani <himanshu.madhani@cavium.com> Signed-off-by: Bart Van Assche <bart.vanassche@sandisk.com> Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
2017-02-08qla2xxx: Remove SRR codeHimanshu Madhani
During initial implementation, tape support was included but not enabled by default on target. So far, we don't see any target customer requesting this support. Since this code is not being used actively, we want to remove it and we will add back if there are any request in future for SRR support. Signed-off-by: Himanshu Madhani <himanshu.madhani@cavium.com> Signed-off-by: Giridhar Malavali <giridhar.malavali@cavium.com> Reviewed-by: Christoph Hellwig <hch@lst.de> Signed-off-by: Bart Van Assche <bart.vanassche@sandisk.com> Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
2017-02-08qla2xxx: Make trace flags more readableQuinn Tran
Trace flags are useful during debugging crash dumps using crash utility. These trace flags makes it easier to understand various states a command has successfully completed. Signed-off-by: Quinn Tran <quinn.tran@cavium.com> Signed-off-by: Himanshu Madhani <himanshu.madhani@cavium.com> Signed-off-by: Bart Van Assche <bart.vanassche@sandisk.com> Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
2017-02-08qla2xxx: Cleanup TMF code translation from qla_targetQuinn Tran
Move code code which converts Task Mgmt Command flags for ATIO to TCM #defines, from qla2xxx driver to tcm_qla2xxx driver. Signed-off-by: Quinn Tran <quinn.tran@cavium.com> Signed-off-by: Himanshu Madhani <himanshu.madhani@cavium.com> Reviewed-by: Christoph Hellwig <hch@lst.de> Signed-off-by: Bart Van Assche <bart.vanassche@sandisk.com> Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
2017-02-08qla2xxx: Remove direct access of scsi_status field in se_cmdQuinn Tran
Signed-off-by: Quinn Tran <quinn.tran@cavium.com> Signed-off-by: Himanshu Madhani <himanshu.madhani@cavium.com> Reviewed-by: Christoph Hellwig <hch@lst.de> Signed-off-by: Bart Van Assche <bart.vanassche@sandisk.com> Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
2017-02-08ibmvscsis: Add SGL limitBryant G. Ly
This patch adds internal LIO sgl limit since the driver already sets a max transfer limit on transport layer of 1MB to the client. Cc: stable@vger.kernel.org Tested-by: Steven Royer <seroyer@linux.vnet.ibm.com> Signed-off-by: Bryant G. Ly <bryantly@linux.vnet.ibm.com> Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
2017-02-07scsi: ufs: dump hw regs on link failuresVenkat Gopalakrishnan
Dump host state, power info and host/vendor specific registers on link failures. This provides useful info to debug the failures. Signed-off-by: Venkat Gopalakrishnan <venkatg@codeaurora.org> Signed-off-by: Subhash Jadavani <subhashj@codeaurora.org> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
2017-02-07scsi: ufs-qcom: dump additional testbus registersVenkat Gopalakrishnan
Change testbus default config, dump additional testbus registers along with other debug vendor specific registers. These additional info are useful in debugging link related failures. Signed-off-by: Venkat Gopalakrishnan <venkatg@codeaurora.org> Signed-off-by: Subhash Jadavani <subhashj@codeaurora.org> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
2017-02-07scsi: ufs: kick start clock scaling only after device detectionsubhashj@codeaurora.org
UFS clock scaling might start kicking in even before the device is running at the fastest interface speed which is undesirable. This change moves the clock scaling kick start only after the device is detected and running at the fastest interface speed. Signed-off-by: Subhash Jadavani <subhashj@codeaurora.org> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
2017-02-07scsi: ufs: don't suspend clock scaling during clock gatingsubhashj@codeaurora.org
Currently we are suspending clock scaling during clock gating which doesn't allow us to have clock gating timeout lower than clock scaling polling window. If clock gating timeout is smaller than the clock scaling polling window then we will mostly suspend the clock scaling before clock scaling polling window expires and we might get stuck in same state (scaled down or scaled up) for quite a long time. And for this reason, we have clock gating timeout (150ms) greater than clock scaling polling window (100ms). We would like to have aggressive clock gating timeout even lower than the clock scaling polling window hence this change is decoupling the clock scaling suspend/resume from clock gate/ungate. We will not suspend the clock scaling as part of clock gating instead clock scaling context will schedule scaling suspend work if there are no more pending transfer requests. Signed-off-by: Subhash Jadavani <subhashj@codeaurora.org> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
2017-02-07scsi: ufs: add host state prints in failure casesGilad Broner
Whenever some UFS failure occurs the driver prints the UFS registers in order to help with analysis of the failure. However this may not be sufficient in some cases, so having the host controller state as it is represented and managed in the driver will contribute to analysis efforts. Added prints of various fields in the hba struct which may be of interest. Signed-off-by: Gilad Broner <gbroner@codeaurora.org> Signed-off-by: Subhash Jadavani <subhashj@codeaurora.org> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
2017-02-07scsi: ufs: add load based scaling of UFS gearsubhashj@codeaurora.org
UFS driver's load based clock scaling feature scales down the ufs related clocks in order to allow low power modes of chipsets. UniPro 1.6 supports maximum gear up to HS-G3 (High Speed Gear3) and some of the chipsets low power modes may not be allowed in HS-G3 hence this change adds support to scale gear between HS-G3 and HS-G1 based on same existing load based clock scaling logic. Signed-off-by: Subhash Jadavani <subhashj@codeaurora.org> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
2017-02-07scsi: ufs: reduce printout for aborted requestsGilad Broner
Details printed for each request that is aborted can overload the target as there can be several requests that are aborted at once. This change will print full request details only for the first aborted request since the last link reset, and minimal details for other subsequent requests. Signed-off-by: Gilad Broner <gbroner@codeaurora.org> Signed-off-by: Subhash Jadavani <subhashj@codeaurora.org> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
2017-02-07scsi: ufs: skip request abort task when previous aborts failedGilad Broner
On certain error conditions request abort task itself might fail when aborting a request. In such case, subsequent request aborts should skip issuing the abort task as it is expected to fail as well, and device reset handler will be called next. Signed-off-by: Gilad Broner <gbroner@codeaurora.org> Signed-off-by: Subhash Jadavani <subhashj@codeaurora.org> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
2017-02-07scsi: aacraid: avoid open-coded upper_32_bitsArnd Bergmann
Shifting a dma_addr_t right by 32 bits causes a compile-time warning when that type is only 32 bit wide: drivers/scsi/aacraid/src.c: In function 'aac_src_start_adapter': drivers/scsi/aacraid/src.c:414:29: error: right shift count >= width of type [-Werror=shift-count-overflow] This changes the driver to use the predefined macros consistently, including one correct but open-coded upper_32_bits() instance. Fixes: d1ef4da8487f ("scsi: aacraid: added support for init_struct_8") Fixes: 423400e64d37 ("scsi: aacraid: Include HBA direct interface") Signed-off-by: Arnd Bergmann <arnd@arndb.de> Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de> Reviewed-by: Raghava Aditya Renukunta <RaghavaAditya.Renukunta@microsemi.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
2017-02-07scsi: aacraid: rcode is unsigned and should be signed intColin Ian King
aac_fib_send can return -ve error returns and hence rcode should be signed. Currently the rcode >= 0 check is always true and -ve errors are not being checked. Thanks to Dan Carpenter for spotting my original broken fix to this issue. Signed-off-by: Colin Ian King <colin.king@canonical.com> Reviewed-by: Raghava Aditya Renukunta <RaghavaAditya.Renukunta@microsemi.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
2017-02-07Merge git://git.kernel.org/pub/scm/linux/kernel/git/davem/netDavid S. Miller
The conflict was an interaction between a bug fix in the netvsc driver in 'net' and an optimization of the RX path in 'net-next'. Signed-off-by: David S. Miller <davem@davemloft.net>
2017-02-06scsi: pm8001: switch to pci_irq_alloc_vectorsChristoph Hellwig
Signed-off-by: Christoph Hellwig <hch@lst.de> Acked-by: Jack Wang <jinpu.wang@profitbricks.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
2017-02-06scsi: remove tsk_mgmt_response and it_nexus_response transport methodsChristoph Hellwig
They are never called and just dispatch to methods of the same names in the FC and SRP transport classes that are never implemented. Signed-off-by: Christoph Hellwig <hch@lst.de> Reviewed-by: Hannes Reinecke <hare@suse.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
2017-02-06scsi: remove eh_timed_out methods in the transport templateChristoph Hellwig
Instead define the timeout behavior purely based on the host_template eh_timed_out method and wire up the existing transport implementations in the host templates. This also clears up the confusion that the transport template method overrides the host template one, so some drivers have to re-override the transport template one. Signed-off-by: Christoph Hellwig <hch@lst.de> Reviewed-by: Hannes Reinecke <hare@suse.com> Reviewed-by: Tyrel Datwyler <tyreld@linux.vnet.ibm.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
2017-02-06scsi: libsas: remove sas_scsi_timed_outChristoph Hellwig
EH_NOT_HANDLED is the default case if no eh_timed_out method is provided, so there is no need to supply it. Signed-off-by: Christoph Hellwig <hch@lst.de> Reviewed-by: Hannes Reinecke <hare@suse.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
generated by cgit v1.2.3 (git 2.39.1) at 2025-08-04 05:15:43 +0000