| Age | Commit message (Collapse) | Author |
|---|
|
Prior patch mixed up what argument in the macro was what, so min value
was placed as the "default" argument, and the default value was placed
as the "min" argument. Thus, when the default was applied, it looked
like the default was smaller than the allowed min.
Swap argument postions to correct.
[mkp: fixed checkpatch warning]
Signed-off-by: James Smart <james.smart@broadcom.com>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
If log verbose in not turned on, its hard to tell when certain error
paths get hit. Add stats counters and corresponding logic to
debugfs/sysfs to aid understanding what paths were traversed.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <james.smart@broadcom.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
The logic for sg_seg_cnt is a bit convoluted. This patch tries to clean
up a couple of areas, especially around the +2 and +1 logic.
This patch:
- Cleans up the lpfc_sg_seg_cnt attribute to specify a real minimum
rather than making the minimum be whatever the default is.
- Removes the hardcoding of +2 (for the number of elements we use in a
sgl for cmd iu and rsp iu) and +1 (an additional entry to compensate
for nvme's reduction of io size based on a possible partial page)
logic in sg list initialization. In the case where the +1 logic is
referenced in host and target io checks, use the values set in the
transport template as that value was properly set.
There can certainly be more done in this area and it will be addressed
in combined host/target driver effort.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <james.smart@broadcom.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
The current default for async hw receive queues is 1, which presents
issues under heavy load as number of queues influence the available
async receive buffer limits.
Raise the default to the either the current hw limit (16) or the number
of hw qs configured (io channel value).
Revise the attribute definition for mrq to better reflect what we do for
hw queues. E.g. 0 means default to optimal (# of cpus), non-zero
specifies a specific limit. Before this change, mrq=0 meant target mode
was disabled. As 0 now has a different meaning, rework the if tests to
use the better nvmet_support check.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <james.smart@broadcom.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
Pull SCSI updates from James Bottomley:
"This is mostly updates of the usual suspects: lpfc, qla2xxx, hisi_sas,
megaraid_sas, pm80xx, mpt3sas, be2iscsi, hpsa. and a host of minor
updates.
There's no major behaviour change or additions to the core in all of
this, so the potential for regressions should be small (biggest
potential being in the scsi error handler changes)"
* tag 'scsi-misc' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi: (203 commits)
scsi: lpfc: Fix hard lock up NMI in els timeout handling.
scsi: mpt3sas: remove a stray KERN_INFO
scsi: mpt3sas: cleanup _scsih_pcie_enumeration_event()
scsi: aacraid: use timespec64 instead of timeval
scsi: scsi_transport_fc: add 64GBIT and 128GBIT port speed definitions
scsi: qla2xxx: Suppress a kernel complaint in qla_init_base_qpair()
scsi: mpt3sas: fix dma_addr_t casts
scsi: be2iscsi: Use kasprintf
scsi: storvsc: Avoid excessive host scan on controller change
scsi: lpfc: fix kzalloc-simple.cocci warnings
scsi: mpt3sas: Update mpt3sas driver version.
scsi: mpt3sas: Fix sparse warnings
scsi: mpt3sas: Fix nvme drives checking for tlr.
scsi: mpt3sas: NVMe drive support for BTDHMAPPING ioctl command and log info
scsi: mpt3sas: Add-Task-management-debug-info-for-NVMe-drives.
scsi: mpt3sas: scan and add nvme device after controller reset
scsi: mpt3sas: Set NVMe device queue depth as 128
scsi: mpt3sas: Handle NVMe PCIe device related events generated from firmware.
scsi: mpt3sas: API's to remove nvme drive from sml
scsi: mpt3sas: API 's to support NVMe drive addition to SML
...
|
|
This patch calls the new nvme transport routine for dev_loss_tmo
whenever the SCSI fc transport calls the lldd to make a dynamic
change to a remote ports dev_loss_tmo.
Signed-off-by: James Smart <james.smart@broadcom.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
|
|
The descriptions for lpfc_xri_split and lpfc_enable_fc4_type were
poor. Revise for better understanding:
lpfc_xri_split - Percentage of FCP XRI resources versus NVME
lpfc_enable_fc4_type - Enable FC4 Protocol support - FCP / NVME
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <james.smart@broadcom.com>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
The driver crashes when attempting to use a freed ndpl pointer.
The pci_remove_one handler runs on a separate kernel thread. The order
of the removal is starting by freeing all of the ndlps and then
disabling interrupts. In between these two events the driver can still
receive an ELS and process it. When it tries to use the ndlp pointer
will be NULL
Change the order of the pci_remove_one vs disable interrupts so that
interrupts are disabled before the ndlp's are freed.
Cc: <stable@vger.kernel.org> # 4.12+
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <james.smart@broadcom.com>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
Pull SCSI updates from James Bottomley:
"This is mostly updates of the usual suspects: lpfc, qla2xxx, hisi_sas,
megaraid_sas, zfcp and a host of minor updates.
The major driver change here is the elimination of the block based
cciss driver in favour of the SCSI based hpsa driver (which now drives
all the legacy cases cciss used to be required for). Plus a reset
handler clean up and the redo of the SAS SMP handler to use bsg lib"
* tag 'scsi-misc' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi: (279 commits)
scsi: scsi-mq: Always unprepare before requeuing a request
scsi: Show .retries and .jiffies_at_alloc in debugfs
scsi: Improve requeuing behavior
scsi: Call scsi_initialize_rq() for filesystem requests
scsi: qla2xxx: Reset the logo flag, after target re-login.
scsi: qla2xxx: Fix slow mem alloc behind lock
scsi: qla2xxx: Clear fc4f_nvme flag
scsi: qla2xxx: add missing includes for qla_isr
scsi: qla2xxx: Fix an integer overflow in sysfs code
scsi: aacraid: report -ENOMEM to upper layer from aac_convert_sgraw2()
scsi: aacraid: get rid of one level of indentation
scsi: aacraid: fix indentation errors
scsi: storvsc: fix memory leak on ring buffer busy
scsi: scsi_transport_sas: switch to bsg-lib for SMP passthrough
scsi: smartpqi: remove the smp_handler stub
scsi: hpsa: remove the smp_handler stub
scsi: bsg-lib: pass the release callback through bsg_setup_queue
scsi: Rework handling of scsi_device.vpd_pg8[03]
scsi: Rework the code for caching Vital Product Data (VPD)
scsi: rcu: Introduce rcu_swap_protected()
...
|
|
Add Buffer to buffer credit recovery support to the driver. This is a
negotiated feature with the peer that allows for both sides to detect
dropped RRDY's and FC Frames and recover credit.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <james.smart@broadcom.com>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
Various oops including cpu LOCKUPs were seen.
For asynchronously received ius where the driver must assign exchange
resources, the resources were on a single get (free) list and put list
(finished, waiting to be put on get list). As all cpus are sharing the
lists, an interrupt for a receive frame may have to wait for all the
other cpus to place their done work onto the put list before it can
acquire the lock to pull from the list.
Fix by breaking the resource lists into per-cpu lists or at least more
than 1 list with cpu's sharing the lists). A cpu would allocate from the
free list for its own cpu, and put its done work on the its own put list
- avoiding the contention. As cpu load may vary, when empty, a cpu may
grab from another cpu, thereby changing resource distribution. But
searching for a resource only occurs on 1 or a few cpus until a single
resource can be allocated. if the condition reoccurs, it starts looking
at a different cpu.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <james.smart@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
Currently, calls to nvmet_fc_rcv_fcp_req() always copied the
FC-NVME cmd iu to a temporary buffer before returning, allowing
the driver to immediately repost the buffer to the hardware.
To address timing conditions on queue element structures vs async
command reception, the nvmet_fc transport occasionally may need to
hold on to the command iu buffer for a short period. In these cases,
the nvmet_fc_rcv_fcp_req() will return a special return code
(-EOVERFLOW). In these cases, the LLDD must delay until the new
defer_rcv lldd callback is called before recycling the buffer back
to the hw.
This patch adds support for the new nvmet_fc transport defer_rcv
callback and recognition of the new error code when passing commands
to the transport.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <james.smart@broadcom.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
|
|
Since unsol rcv ISR and command cmpl ISR both access/lock this list,
separate get/put lists will reduce contention.
Replaced
struct list_head lpfc_nvmet_ctx_list;
with
struct list_head lpfc_nvmet_ctx_get_list;
struct list_head lpfc_nvmet_ctx_put_list;
and all correpsonding locks and counters.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <james.smart@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
First line of nvme_info output is not consistent. There is an Extra
colon in the format.
First line of output will contain one of the following strings:
NVME Initiator Enabled
NVME Target Enabled
NVME Disabled
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <james.smart@broadcom.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
Administrator intervention is currently required to get good numbers
when switching from running latency tests to IOPS tests.
The configured interrupt coalescing values will greatly effect the
results of these tests. Currently, the driver has a single coalescing
value set by values of the module attribute. This patch changes the
driver to support auto-configuration of the coalescing value based on
the total number of outstanding IOs and average number of CQEs processed
per interrupt for an EQ. Values are checked every 5 seconds.
The driver defaults to the automatic selection. Automatic selection can
be disabled by the new lpfc_auto_imax module_parameter.
Older hardware can only change interrupt coalescing by mailbox
command. Newer hardware supports change via a register. The patch
support both.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <james.smart@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
failure
On hbacmd reset failure, observing wrong string "nline" in kernel log.
On failure, non negative value (1) is returned from sysfs store
routine. It is interpreted as count by kernel and store routine is
called again with the remaining characters as input.
Fix: Return negative error code (-EIO) in case of failure.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <james.smart@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
NVME FC counters don't reflect actual results
Since counters are not atomic, or protected by a lock, the values often
get screwed up.
Make them atomic, like NVMET. Fix up sysfs and debugfs display
accordingly Added Outstanding IOs to stats display
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <james.smart@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
While debugging Devloss and recovery, debugfs and sysfs were found to
not show the NVME port roles consistently.
The port role FC_PORT_ROLE_NVME_DISCOVERY was added with the devloss
bringup and the other issues were just oversight.
Add NVME Target and DISCSRVC to debugfs nodeinfo and sysfs nvme info
handlers. The full port role was added to the NVME data only not the
generic nodelist.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <james.smart@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
As the devloss API was implemented in the nvmei driver, an evaluation of
the nvme transport and the lpfc driver showed dual management of the
rports. This creates a bug possibility when the thread count and SAN
size increases.
The nvmei driver code was based on a very early transport and was not
revisited until the devloss API was introduced.
Remove the listhead in the driver's rport data structure and the
listhead in the driver's lport data structure. Remove all rport_list
traversal. Convert the driver to use the nrport (nvme rport) pointer
that is now NULL or nonNULL depending on a devloss action. Convert
debugfs and nvme_info in sysfs to use the fc_nodes list in the vport.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <james.smart@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
Add nvme initiator devloss support
The existing implementation was based on no devloss behavior in the
transport (e.g. immediate teardown) so code didn't properly handle
delayed nvme rport device unregister calls. In addition, the driver was
not correctly cycling the rport port role for each
register-unregister-reregister process.
This patch does the following:
Rework the code to properly handle rport device unregister calls and
potential re-allocation of the remoteport structure if the port comes
back in under dev_loss_tmo.
Correct code that was incorrectly cycling the rport port role for each
register-unregister-reregister process.
Prep the code to enable calling the nvme_fc transport api to dynamically
update dev_loss_tmo when the scsi sysfs interface changes it.
Memset the rpinfo structure in the registration call to enforce "accept
nvme transport defaults" in the registration call. Driver parameters do
influence the dev_loss_tmo transport setting dynamically.
Simplifies the register function: the driver was incorrectly searching
its local rport list to determine resume or new semantics, which is not
valid as the transport already handles this. The rport was resumed if
the rport handed back matches the ndlp->nrport pointer. Otherwise,
devloss fired and the ndlp's nrport is NULL.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <james.smart@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
Previous logic would just drop the IO.
Added logic to queue the IO to wait for an IO context resource from an
IO thats already in progress.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <james.smart@broadcom.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
Currently IO resources are mapped 1 to 1 with RQ buffers posted
Added logic to separate RQE buffers from IO op resources
(sgl/iocbq/context). During initialization, the driver will determine
how many SGLs it will allocate for NVMET (based on what the firmware
reports) and associate a NVMET IOCBq and NVMET context structure with
each one.
Now that hdr/data buffers are immediately reposted back to the RQ, 512
RQEs for each MRQ is sufficient. Also, since NVMET data buffers are now
128 bytes, lpfc_nvmet_mrq_post is not necessary anymore as we will
always post the max (512) buffers per NVMET MRQ.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <james.smart@broadcom.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
Large block writes to the nvme target were failing because the default
number of RQs posted was insufficient.
Expand the NVMET RQs to 2048 RQEs and ensure a minimum of 512 RQEs are
posted, no matter how many MRQs are configured.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <james.smart@broadcom.com>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
More debug messages added for nvme statistics.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <james.smart@broadcom.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
Pull SCSI updates from James Bottomley:
"This update includes the usual round of major driver updates
(hisi_sas, ufs, fnic, cxlflash, be2iscsi, ipr, stex). There's also the
usual amount of cosmetic and spelling stuff"
* tag 'scsi-misc' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi: (155 commits)
scsi: qla4xxx: fix spelling mistake: "Tempalate" -> "Template"
scsi: stex: make S6flag static
scsi: mac_esp: fix to pass correct device identity to free_irq()
scsi: aacraid: pci_alloc_consistent() failures on ARM64
scsi: ufs: make ufshcd_get_lists_status() register operation obvious
scsi: ufs: use MASK_EE_STATUS
scsi: mac_esp: Replace bogus memory barrier with spinlock
scsi: fcoe: make fcoe_e_d_tov and fcoe_r_a_tov static
scsi: sd_zbc: Do not write lock zones for reset
scsi: sd_zbc: Remove superfluous assignments
scsi: sd: sd_zbc: Rename sd_zbc_setup_write_cmnd
scsi: Improve scsi_get_sense_info_fld
scsi: sd: Cleanup sd_done sense data handling
scsi: sd: Improve sd_completed_bytes
scsi: sd: Fix function descriptions
scsi: mpt3sas: remove redundant wmb
scsi: mpt: Move scsi_remove_host() out of mptscsih_remove_host()
scsi: sg: reset 'res_in_use' after unlinking reserved array
scsi: mvumi: remove code handling zero scsi_sg_count(scmd) case
scsi: fusion: fix spelling mistake: "Persistancy" -> "Persistency"
...
|
|
Adding support for Fabric assigned WWPN and WWNN.
Firmware sends first FLOGI to fabric with vendor version changes.
On link up driver gets updated service parameter with FAWWN assigned port
name. Driver sends 2nd FLOGI with updated fawwpn and modifies the
vport->fc_portname in driver.
Note:
Soft wwpn will not be allowed when fawwpn is enabled.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <james.smart@broadcom.com>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
|
|
Fix nvme initiator handline when CONFIG_LPFC_NVME_INITIATOR is not enabled.
With update nvme upstream driver sources, loading
the driver with nvme enabled resulting in this Oops.
BUG: unable to handle kernel NULL pointer dereference at 0000000000000018
IP: lpfc_nvme_update_localport+0x23/0xd0 [lpfc]
PGD 0
Oops: 0000 [#1] SMP
CPU: 0 PID: 10256 Comm: lpfc_worker_0 Tainted
Hardware name: ...
task: ffff881028191c40 task.stack: ffff880ffdf00000
RIP: 0010:lpfc_nvme_update_localport+0x23/0xd0 [lpfc]
RSP: 0018:ffff880ffdf03c20 EFLAGS: 00010202
Cause: As the initiator driver completes discovery at different stages,
it call lpfc_nvme_update_localport to hint that the DID and role may have
changed. In the implementation of lpfc_nvme_update_localport, the driver
was not validating the localport or the lport during the execution
of the update_localport routine. With the recent upstream additions to
the driver, the create_localport routine didn't run and so the localport
was NULL causing the page-fault Oops.
Fix: Add the CONFIG_LPFC_NVME_INITIATOR preprocessor inclusions to
lpfc_nvme_update_localport to turn off all routine processing when
the running kernel does not have NVME configured. Add NULL pointer
checks on the localport and lport in lpfc_nvme_update_localport and
dump messages if they are NULL and just exit.
Also one alingment issue fixed.
Repalces the ifdef with the IS_ENABLED macro.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <james.smart@broadcom.com>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
|
|
This patch fixes a potential buffer overflow in lpfc_nvme_info_show().
Signed-off-by: Maurizio Lombardi <mlombard@redhat.com>
Reviewed-by: Ewan D. Milne <emilne@redhat.com>
Acked-by: James Smart <james.smart@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
|
|
Reviewing the result of what was just added for Kconfig, we made a poor
choice. It worked well for full kernel builds, but not so much for how
it would be deployed on a distro.
Here's the final result:
- lpfc will compile in NVME initiator and/or NVME target support based
on whether the kernel has the corresponding subsystem support.
Kconfig is not used to drive this specifically for lpfc.
- There is a module parameter, lpfc_enable_fc4_type, that indicates
whether the ports will do FCP-only or FCP & NVME (NVME-only not yet
possible due to dependency on fc transport). As FCP & NVME divvys up
exchange resources, and given NVME will not be often initially, the
default is changed to FCP only.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <james.smart@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
|
|
Without apriori understanding of what the define is, the name gives
a very different impression of what it is (a max delay value
for an EQ). Rename the define so it reflects what it is: the number
of EQ IDs that can be set in one instance of the MODIFY_EQ_DELAY
mbx command.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <james.smart@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
A previous change unilaterally removed the hba reset entry point
from the sli3 host template. This was done to allow tape devices
being used for back up from being removed. Why was this done ?
When there was non-responding device on the fabric, the error
escalation policy would escalate to the reset handler. When the
reset handler was called, it would reset the adapter, dropping
link, thus logging out and terminating all i/o's - on any target.
If there was a tape device on the same adapter that wasn't in
error, it would kill the tape i/o's, effectively killing the
tape device state. With the reset point removed, the adapter
reset avoided the fabric logout, allowing the other devices to
continue to operate unaffected. A hack - yes. Hint: we really
need a transport I_T nexus reset callback added to the eh process
(in between the SCSI target reset and hba reset points), so a
fc logout could occur to the one bad target only and stop the error
escalation process.
This patch commonizes the approach so it can be used for sli3 and sli4
adapters, but mandates the admin, via module parameter, specifically
identify which adapters the resets are to be removed for. Additionally,
bus_reset, which sends Target Reset TMFs to all targets, is also removed
from the template as it too has the same effect as the adapter reset.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <james.smart@broadcom.com>
Reviewed-by: Laurence Oberman <loberman@redhat.com>
Tested-by: Laurence Oberman <loberman@redhat.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
Pull more SCSI updates from James Bottomley:
"This is the set of stuff that didn't quite make the initial pull and a
set of fixes for stuff which did.
The new stuff is basically lpfc (nvme), qedi and aacraid. The fixes
cover a lot of previously submitted stuff, the most important of which
probably covers some of the failing irq vectors allocation and other
fallout from having the SCSI command allocated as part of the block
allocation functions"
* tag 'scsi-misc' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi: (59 commits)
scsi: qedi: Fix memory leak in tmf response processing.
scsi: aacraid: remove redundant zero check on ret
scsi: lpfc: use proper format string for dma_addr_t
scsi: lpfc: use div_u64 for 64-bit division
scsi: mac_scsi: Fix MAC_SCSI=m option when SCSI=m
scsi: cciss: correct check map error.
scsi: qla2xxx: fix spelling mistake: "seperator" -> "separator"
scsi: aacraid: Fixed expander hotplug for SMART family
scsi: mpt3sas: switch to pci_alloc_irq_vectors
scsi: qedf: fixup compilation warning about atomic_t usage
scsi: remove scsi_execute_req_flags
scsi: merge __scsi_execute into scsi_execute
scsi: simplify scsi_execute_req_flags
scsi: make the sense header argument to scsi_test_unit_ready mandatory
scsi: sd: improve TUR handling in sd_check_events
scsi: always zero sshdr in scsi_normalize_sense
scsi: scsi_dh_emc: return success in clariion_std_inquiry()
scsi: fix memory leak of sdpk on when gd fails to allocate
scsi: sd: make sd_devt_release() static
scsi: qedf: Add QLogic FastLinQ offload FCoE driver framework.
...
|
|
Fix typos and add the following to the scripts/spelling.txt:
an user||a user
an userspace||a userspace
I also added "userspace" to the list since it is a common word in Linux.
I found some instances for "an userfaultfd", but I did not add it to the
list. I felt it is endless to find words that start with "user" such as
"userland" etc., so must draw a line somewhere.
Link: http://lkml.kernel.org/r/1481573103-11329-4-git-send-email-yamada.masahiro@socionext.com
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Update copyrights to 2017 for all files touched in this patch set
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <james.smart@broadcom.com>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
NVME Target: Receive buffer updates
Allocates buffer pools and configures adapter interfaces to handle
receive buffer (asynchronous FCP CMD ius, first burst data)
from the adapter. Splits by protocol, etc.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <james.smart@broadcom.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
NVME Target: Base modifications
This set of patches adds the base modifications for NVME target support
The base modifications consist of:
- Additional module parameters or configuration tuning
- Enablement of configuration mode for NVME target. Ties into the
queueing model put into place by the initiator basemods patches.
- Target-specific buffer pools, dma pools, sgl pools
[mkp: fixed space at end of file]
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <james.smart@broadcom.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
NVME Initiator: Base modifications
This patch adds base modifications for NVME initiator support.
The base modifications consist of:
- Formal split of SLI3 rings from SLI-4 WQs (sometimes referred to as
rings as well) as implementation now widely varies between the two.
- Addition of configuration modes:
SCSI initiator only; NVME initiator only; NVME target only; and
SCSI and NVME initiator.
The configuration mode drives overall adapter configuration,
offloads enabled, and resource splits.
NVME support is only available on SLI-4 devices and newer fw.
- Implements the following based on configuration mode:
- Exchange resources are split by protocol; Obviously, if only
1 mode, then no split occurs. Default is 50/50. module attribute
allows tuning.
- Pools and config parameters are separated per-protocol
- Each protocol has it's own set of queues, but share interrupt
vectors.
SCSI:
SLI3 devices have few queues and the original style of queue
allocation remains.
SLI4 devices piggy back on an "io-channel" concept that
eventually needs to merge with scsi-mq/blk-mq support (it is
underway). For now, the paradigm continues as it existed
prior. io channel allocates N msix and N WQs (N=4 default)
and either round robins or uses cpu # modulo N for scheduling.
A bunch of module parameters allow the configuration to be
tuned.
NVME (initiator):
Allocates an msix per cpu (or whatever pci_alloc_irq_vectors
gets)
Allocates a WQ per cpu, and maps the WQs to msix on a WQ #
modulo msix vector count basis.
Module parameters exist to cap/control the config if desired.
- Each protocol has its own buffer and dma pools.
I apologize for the size of the patch.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <james.smart@broadcom.com>
----
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
This contains code cleanups that were in the prior patch set.
This allows better review of real changes later.
minor code cleanups:
fix indentation, punctuation, line length
addition/reduction of whitespace
remove unneeded parens, braces
lpfc_debugfs_nodelist_data: print as u64 rather than byte by byte
covert printk(KERN_ERR to pr_err
small print string deltas
use num_present_cpus() rather than count them
comment updates
rctl/type names moved to module variable, not on stack
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <james.smart@broadcom.com>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
When I reversed the patch to re-add the lpfc_soft_wwn parameter feature,
it re-added code that had a long-standing bug. (that's what I get I
guess :)
As Dan Carpenter pointed out - error checks looked at wrong polarity. 0
is success, -errno is failure. Updated checks.
Signed-off-by: James Smart <james.smart@broadcom.com>
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
The lpfc 11.2.0.4 patch set deprecated, by removing, the lpfc_soft_wwn
parameter support.
This patch reinstates support, but adds a warning in the enablement of
the feature that indicates Broadcom (Emulex) does not support the
feature.
Signed-off-by: James Smart <james.smart@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
Deprecate lpfc_prot_sg_seg_cnt parameter. Eliminates driver from
unnecessarily limiting DIF s/g list length.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <james.smart@broadcom.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
Fix Xlane dynamic LUN set for LUN priority. Dynamic changing of the
priority was not getting reflected on the LUN.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <james.smart@broadcom.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
Correct host name in symbolic_name field of nameserver registrations
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <james.smart@broadcom.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
Deprecate lpfc_soft_wwn parameter.
No longer allow override of hw-assigned wwns
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <james.smart@broadcom.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
Synchronize link speed with boot driver
Link speed settings set by the boot driver are reported by the hw.
Driver will attempt to read them, and if set, will respect their
values.
The driver can override the settings with its own if instructed by
user space (via bsg), with the new values being picked up by the
boot driver.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <james.smart@broadcom.com>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
Revise strings with full lpfc parameter name
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <james.smart@broadcom.com>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
Code cleanup for lpfc_sriov_nr_virtfn parameter
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <james.smart@broadcom.com>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
Code cleanup for lpfc_max_scsicmpl_time parameter
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <james.smart@broadcom.com>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
