| Age | Commit message (Collapse) | Author |
|---|
|
[ Upstream commit 30cc7b0d0e9341d419eb7da15fb5c22406dbe499 ]
The charge input threshold voltage register on the MAX77693 PMIC accepts
four values: 0x0 for 4.3v, 0x1 for 4.7v, 0x2 for 4.8v and 0x3 for 4.9v.
Due to an oversight, the driver calculated the values for 4.7v and above
starting from 0x0, rather than from 0x1 ([(4700000 - 4700000) / 100000]
gives 0).
Add 1 to the calculation to ensure that 4.7v is converted to a register
value of 0x1 and that the other two voltages are converted correctly as
well.
Fixes: 87c2d9067893 ("power: max77693: Add charger driver for Maxim 77693")
Signed-off-by: Artur Weber <aweber.kernel@gmail.com>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Link: https://lore.kernel.org/r/20250316-max77693-charger-input-threshold-fix-v1-1-2b037d0ac722@gmail.com
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 45291874a762dbb12a619dc2efaf84598859007a ]
Commit 243f8ffc883a1 ("power: supply: bq27xxx_battery: Notify also about
status changes") intended to notify userspace when the status changes,
based on the flags register. However, the cached state is updated too
early, before the flags are tested for any changes. Remove the premature
update.
Fixes: 243f8ffc883a1 ("power: supply: bq27xxx_battery: Notify also about status changes")
Signed-off-by: Sicelo A. Mhlongo <absicsz@gmail.com>
Link: https://lore.kernel.org/r/20241125152945.47937-1-absicsz@gmail.com
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 98380110bd48fbfd6a798ee11fffff893d36062c ]
Correct the fault handling for the AXP717 by changing the i2c write
from regmap_update_bits() to regmap_write_bits(). The update bits
function does not work properly on a RW1C register where we must
write a 1 back to an existing register to clear it.
Additionally, as part of this testing I confirmed the behavior of
errors reappearing, so remove comment about assumptions.
Fixes: 6625767049c2 ("power: supply: axp20x_battery: add support for AXP717")
Signed-off-by: Chris Morgan <macromorgan@hotmail.com>
Reviewed-by: Chen-Yu Tsai <wens@csie.org>
Link: https://lore.kernel.org/r/20250131231455.153447-2-macroalpha82@gmail.com
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 3fb3cb4350befc4f901c54e0cb4a2a47b1302e08 ]
Size of variable sd_gain equals four bytes - DA9150_QIF_SD_GAIN_SIZE.
Size of variable shunt_val equals two bytes - DA9150_QIF_SHUNT_VAL_SIZE.
The expression sd_gain * shunt_val is currently being evaluated using
32-bit arithmetic. So during the multiplication an overflow may occur.
As the value of type 'u64' is used as storage for the eventual result, put
ULL variable at the first position of each expression in order to give the
compiler complete information about the proper arithmetic to use. According
to C99 the guaranteed width for a variable of type 'unsigned long long' >=
64 bits.
Remove the explicit cast to u64 as it is meaningless.
Just for the sake of consistency, perform the similar trick with another
expression concerning 'iavg'.
Found by Linux Verification Center (linuxtesting.org) with SVACE.
Fixes: a419b4fd9138 ("power: Add support for DA9150 Fuel-Gauge")
Signed-off-by: Andrey Vatoropin <a.vatoropin@crpt.ru>
Link: https://lore.kernel.org/r/20250130090030.53422-1-a.vatoropin@crpt.ru
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
commit afc6e39e824ad0e44b2af50a97885caec8d213d1 upstream.
Fix set charge current limits for devices which allow to set the lowest
charge current limit to be greater zero. If requested charge current limit
is below lowest limit, the index equals current_limit_map_size which leads
to accessing memory beyond allocated memory.
Fixes: be2919d8355e ("power: supply: gpio-charger: add charge-current-limit feature")
Cc: stable@vger.kernel.org
Signed-off-by: Dimitri Fedrau <dimitri.fedrau@liebherr.com>
Link: https://lore.kernel.org/r/20241209-fix-charge-current-limit-v1-1-760d9b8f2af3@liebherr.com
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit c28dc9fc24f5fa802d44ef7620a511035bdd803e upstream.
ECs implementing the v2 command will not stop charging when the end
threshold is reached. Instead they will begin discharging until the
start threshold is reached, leading to permanent charge and discharge
cycles. This defeats the point of the charge control mechanism.
Avoid the issue by hiding the start threshold on v2 systems.
Instead on those systems program the EC with start == end which forces
the EC to reach and stay at that level.
v1 does not support thresholds and v3 works correctly,
at least judging from the code.
Reported-by: Thomas Koch <linrunner@gmx.net>
Fixes: c6ed48ef5259 ("power: supply: add ChromeOS EC based charge control driver")
Cc: stable@vger.kernel.org
Signed-off-by: Thomas Weißschuh <linux@weissschuh.net>
Link: https://lore.kernel.org/r/20241208-cros_charge-control-v2-v1-3-8d168d0f08a3@weissschuh.net
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit e65a1b7fad0e112573eea7d64d4ab4fc513b8695 upstream.
Allow setting the start and stop thresholds to the same value.
There is no reason to disallow it.
Suggested-by: Thomas Koch <linrunner@gmx.net>
Fixes: c6ed48ef5259 ("power: supply: add ChromeOS EC based charge control driver")
Cc: stable@vger.kernel.org
Signed-off-by: Thomas Weißschuh <linux@weissschuh.net>
Link: https://lore.kernel.org/r/20241208-cros_charge-control-v2-v1-2-8d168d0f08a3@weissschuh.net
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit e5f84d1cf562f7b45e28d6e5f6490626f870f81c upstream.
Concurrent accesses through sysfs may lead to inconsistent state in the
priv data. Introduce a mutex to avoid this.
Fixes: c6ed48ef5259 ("power: supply: add ChromeOS EC based charge control driver")
Cc: stable@vger.kernel.org
Signed-off-by: Thomas Weißschuh <linux@weissschuh.net>
Link: https://lore.kernel.org/r/20241208-cros_charge-control-v2-v1-1-8d168d0f08a3@weissschuh.net
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit b3ded6072c5600704cfa3ce3a8dc8718d34bda66 ]
There are 2 issues with bq24296_set_otg_vbus():
1. When writing the OTG_CONFIG bit it uses POC_CHG_CONFIG_SHIFT which
should be POC_OTG_CONFIG_SHIFT.
2. When turning the regulator off it never turns charging back on. Note
this must be done through bq24190_charger_set_charge_type(), to ensure
that the charge_type property value of none/trickle/fast is honored.
Resolve both issues to fix BQ24296 Vbus regulator support not working.
Fixes: b150a703b56f ("power: supply: bq24190_charger: Add support for BQ24296")
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Link: https://lore.kernel.org/r/20241116203648.169100-2-hdegoede@redhat.com
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit b6d445f6724deda3fd87fa33358009d947a64c5d ]
This fails to link when compile-testing and the auxiliary bus is not built-in:
x86_64-linux-ld: drivers/power/reset/ep93xx-restart.o: in function `ep93xx_reboot_driver_init':
ep93xx-restart.c:(.init.text+0x11): undefined reference to `__auxiliary_driver_register'
x86_64-linux-ld: drivers/power/reset/ep93xx-restart.o: in function `ep93xx_reboot_driver_exit':
ep93xx-restart.c:(.exit.text+0x8): undefined reference to `auxiliary_driver_unregister'
Add the appropriate dependency.
Fixes: 9fa7cdb4368f ("power: reset: Add a driver for the ep93xx reset")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Link: https://lore.kernel.org/r/20241111104418.3891756-1-arnd@kernel.org
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit c46a9ee5c6210682611d3d4276436c23a95e1996 ]
Use IC status regfield to rewrite the 'get_staus' function. The original
one cannot cover some special scenario like as charger OTG or JEITA case.
Fixes: 4a1a5f6781d8 ("power: supply: rt9471: Add Richtek RT9471 charger driver")
Reported-by: Lucas Tsai <lucas_tsai@richtek.com>
Signed-off-by: ChiYuan Huang <cy_huang@richtek.com>
Link: https://lore.kernel.org/r/67ba92bb4a9c51d9cafadab30b788a3a2c3048e1.1727252762.git.cy_huang@richtek.com
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit d10ff07dd2b933e3864c592ca932996b07bbf22a ]
Fix F_WDT and F_WDT_RST wrong regfield declaration.
Fixes: 4a1a5f6781d8 ("power: supply: rt9471: Add Richtek RT9471 charger driver")
Reported-by: Lucas Tsai <lucas_tsai@richtek.com>
Signed-off-by: ChiYuan Huang <cy_huang@richtek.com>
Link: https://lore.kernel.org/r/f862e23f220612f01fabb6d8e76cfaf63756c22b.1727252762.git.cy_huang@richtek.com
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 34f99d3b706a519e556841f405c224ca708b1f54 ]
Correct bq27426 registers, according to technical reference manual
it does not have Design Capacity register so it is not register
compatible with bq27421.
Fixes: 5ef6a16033b47 ("power: supply: bq27xxx: Add support for BQ27426")
Signed-off-by: Barnabás Czémán <barnabas.czeman@mainlining.org>
Link: https://lore.kernel.org/r/20241016-fix_bq27426-v2-1-aa6c0f51a9f6@mainlining.org
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit f6da4553ff24a5d1c959c9627c965323adc3d307 ]
The put_device() call in power_supply_put() may call
power_supply_dev_release(). The latter function does not sleep so
power_supply_put() doesn't sleep either. Hence, remove the might_sleep()
call from power_supply_put(). This patch suppresses false positive
complaints about calling a sleeping function from atomic context if
power_supply_put() is called from atomic context.
Cc: Kyle Tso <kyletso@google.com>
Cc: Krzysztof Kozlowski <krzk@kernel.org>
Fixes: 1a352462b537 ("power_supply: Add power_supply_put for decrementing device reference counter")
Signed-off-by: Bart Van Assche <bvanassche@acm.org>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Link: https://lore.kernel.org/r/20240917193914.47566-1-bvanassche@acm.org
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit f82bf3c5796e1630d553669fb451e6c9d4070512 ]
This driver uses various OF-specific functions and depends on phandle
parsing. There's no reason to make it available to non-OF systems so add
a relevant dependency switch to its Kconfig entry.
Fixes: 2f1630f437df ("power: pwrseq: add a driver for the PMU module on the QCom WCN chipsets")
Link: https://lore.kernel.org/r/20241004130449.51725-1-brgl@bgdev.pl
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
asm/unaligned.h is always an include of asm-generic/unaligned.h;
might as well move that thing to linux/unaligned.h and include
that - there's nothing arch-specific in that header.
auto-generated by the following:
for i in `git grep -l -w asm/unaligned.h`; do
sed -i -e "s/asm\/unaligned.h/linux\/unaligned.h/" $i
done
for i in `git grep -l -w asm-generic/unaligned.h`; do
sed -i -e "s/asm-generic\/unaligned.h/linux\/unaligned.h/" $i
done
git mv include/asm-generic/unaligned.h include/linux/unaligned.h
git mv tools/include/asm-generic/unaligned.h tools/include/linux/unaligned.h
sed -i -e "/unaligned.h/d" include/asm-generic/Kbuild
sed -i -e "s/__ASM_GENERIC/__LINUX/" include/linux/unaligned.h tools/include/linux/unaligned.h
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc
Pull SoC update from Arnd Bergmann:
"Convert ep93xx to devicetree
This concludes a long journey towards replacing the old board files
with devictree description on the Cirrus Logic EP93xx platform.
Nikita Shubin has been working on this for a long time, for details
see the last post on
https://lore.kernel.org/lkml/20240909-ep93xx-v12-0-e86ab2423d4b@maquefel.me/"
* tag 'soc-ep93xx-dt-6.12' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc: (47 commits)
dt-bindings: gpio: ep9301: Add missing "#interrupt-cells" to examples
MAINTAINERS: Update EP93XX ARM ARCHITECTURE maintainer
soc: ep93xx: drop reference to removed EP93XX_SOC_COMMON config
net: cirrus: use u8 for addr to calm down sparse
dmaengine: cirrus: use snprintf() to calm down gcc 13.3.0
dmaengine: ep93xx: Fix a NULL vs IS_ERR() check in probe()
pinctrl: ep93xx: Fix raster pins typo
spi: ep93xx: update kerneldoc comments for ep93xx_spi
clk: ep93xx: Fix off by one in ep93xx_div_recalc_rate()
clk: ep93xx: add module license
dmaengine: cirrus: remove platform code
ASoC: cirrus: edb93xx: Delete driver
ARM: ep93xx: soc: drop defines
ARM: ep93xx: delete all boardfiles
ata: pata_ep93xx: remove legacy pinctrl use
pwm: ep93xx: drop legacy pinctrl
ARM: ep93xx: DT for the Cirrus ep93xx SoC platforms
ARM: dts: ep93xx: Add EDB9302 DT
ARM: dts: ep93xx: add ts7250 board
ARM: dts: add Cirrus EP93XX SoC .dtsi
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/brgl/linux
Pull power sequencing updates from Bartosz Golaszewski:
"There's one change adding support for a new PMU model and another
adding documentation for the subsystem which probably should have been
part of the initial commit but better late than never:
- add support for the new PMU variant inside the WCN6855 chipset
- add documentation for the subsystem"
* tag 'pwrseq-updates-for-v6.12-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/brgl/linux:
Documentation: add a driver API doc for the power sequencing subsystem
power: sequencing: qcom-wcn: add support for the WCN6855 PMU
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/sre/linux-power-supply
Pull power supply and reset updates from Sebastian Reichel:
"Power-supply core:
- introduce power_supply_show_enum_with_available() helper
- change usb_types from an array into a bitmask
- fix early usage of power_supply_property_is_writeable() resulting
in sysfs files not being writable
- fix missing temp1_max_alarm attribute in power-supply's hwmon
devices
Drivers:
- max1720x: expose nvmem device
- brcmstb: cleanup driver to use latest APIs
- max77693: expose input and charging current limit
- max17042_battery: fix state of charge reading for devices without
current sensing
- axp20x_battery: add AXP717 support
- axp20x_battery: fix min/max voltage properties
- axp20x_usb_power: add AXP717 support
- axp20x_usb_power: add DT based input current limit
Documentation updates
Misc minor cleanups and fixes"
* tag 'for-v6.12' of git://git.kernel.org/pub/scm/linux/kernel/git/sre/linux-power-supply: (38 commits)
power: supply: hwmon: Fix missing temp1_max_alarm attribute
power: supply: Drop use_cnt check from power_supply_property_is_writeable()
power: supply: ab8500: Constify struct kobj_type
power: supply: max1720x: fix a double free on error in probe()
power: supply: axp20x_battery: add support for AXP717
power: supply: axp20x_usb_power: Add support for AXP717
dt-bindings: power: supply: axp20x: Add AXP717 compatible
dt-bindings: power: supply: axp20x: Add AXP717 compatible
power: supply: axp20x_usb_power: Fix spelling mistake "reqested" -> "requested"
power: supply: Change usb_types from an array into a bitmask
power: supply: sysfs: Move power_supply_show_enum_with_available() up
power: supply: sysfs: Add power_supply_show_enum_with_available() helper
power: supply: rt9467-charger: Remove "usb_type" property write support
power: supply: ucs1002: Adjust ucs1002_set_usb_type() to accept string values
power: supply: "usb_type" property may be written to
power: supply: max1720x: add read support for nvmem
mfd: axp20x: Add ADC, BAT, and USB cells for AXP717
power: supply: core: constify psy_tzd_ops
power: reset: brcmstb: Do not go into infinite loop if reset fails
power: reset: brcmstb: Use devm_register_sys_off_handler()
...
|
|
Temp channel 0 aka temp1 can have a temp1_max_alarm attribute for
power_supply devices which have a POWER_SUPPLY_PROP_TEMP_ALERT_MAX
property.
HWMON_T_MAX_ALARM was missing from power_supply_hwmon_info for
temp channel 0, causing the hwmon temp1_max_alarm attribute to be
missing from such power_supply devices.
Add this to power_supply_hwmon_info to fix this.
Fixes: f1d33ae806ec ("power: supply: remove duplicated argument in power_supply_hwmon_info")
Cc: stable@vger.kernel.org
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Link: https://lore.kernel.org/r/20240908185337.103696-2-hdegoede@redhat.com
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
|
|
power_supply_property_is_writeable() gets called from the is_visible()
callback for the sysfs attributes of power_supply class devices and for
the sysfs attributes of power_supply core instantiated hwmon class devices.
These sysfs attributes get registered by the device_add() respectively
power_supply_add_hwmon_sysfs() calls in power_supply_register().
use_cnt gets initialized to 0 and is incremented only after these calls.
So when power_supply_property_is_writeable() gets called it always return
-ENODEV because of use_cnt == 0.
This causes all the attributes to have permissions of 444 even those which
should be writable. This used to be a problem only for hwmon sysfs
attributes but since commit be6299c6e55e ("power: supply: sysfs: use
power_supply_property_is_writeable()") this now also impacts power_supply
class sysfs attributes.
Fixes: be6299c6e55e ("power: supply: sysfs: use power_supply_property_is_writeable()")
Fixes: e67d4dfc9ff1 ("power: supply: Add HWMON compatibility layer")
Cc: stable@vger.kernel.org
Cc: Thomas Weißschuh <linux@weissschuh.net>
Cc: Andrey Smirnov <andrew.smirnov@gmail.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Link: https://lore.kernel.org/stable/20240908185337.103696-1-hdegoede%40redhat.com
Link: https://lore.kernel.org/r/20240908185337.103696-1-hdegoede@redhat.com
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
|
|
Implement the reset behaviour of the various EP93xx SoCS
in drivers/power/reset.
It used to be located in arch/arm/mach-ep93xx.
Signed-off-by: Nikita Shubin <nikita.shubin@maquefel.me>
Tested-by: Alexander Sverdlin <alexander.sverdlin@gmail.com>
Acked-by: Sebastian Reichel <sre@kernel.org>
Acked-by: Vinod Koul <vkoul@kernel.org>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
This 'struct kobj_type' is not modified. It is only used in
kobject_init_and_add() which takes a 'const struct kobj_type *ktype'
parameter.
Constifying this structure and moving it to a read-only section,
and can increase over all security.
Signed-off-by: Hongbo Li <lihongbo22@huawei.com>
Link: https://lore.kernel.org/r/20240904011434.2010118-1-lihongbo22@huawei.com
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
|
|
In this code, if devm_add_action_or_reset() fails, it will call
max1720x_unregister_ancillary() which in turn calls
i2c_unregister_device(). Thus the call to i2c_unregister_device() on the
following line is not required and is a double unregister. Delete it.
Fixes: 47271a935619 ("power: supply: max1720x: add read support for nvmem")
Signed-off-by: Dan Carpenter <dan.carpenter@linaro.org>
Link: https://lore.kernel.org/r/9c2f76e7-5679-473b-9b9c-e11b492b96ac@stanley.mountain
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
|
|
Add support for the AXP717 PMIC battery charger. The AXP717 differs
greatly from existing AXP battery chargers in that it cannot measure
the discharge current. The datasheet does not document the current
value's offset or scale, so the POWER_SUPPLY_PROP_CURRENT_NOW is left
unscaled.
Tested-by: Philippe Simons <simons.philippe@gmail.com>
Signed-off-by: Chris Morgan <macromorgan@hotmail.com>
Link: https://lore.kernel.org/r/20240821215456.962564-15-macroalpha82@gmail.com
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
|
|
Add support for the AXP717 PMIC. The AXP717 PMIC allows for detection
of USB type like the AXP813, but has little in common otherwise with
the other AXP PMICs. The USB charger is able to provide between
100000uA and 3250000uA of power, and can measure the VBUS input in mV
with up to 14 bits of precision.
Tested-by: Philippe Simons <simons.philippe@gmail.com>
Signed-off-by: Chris Morgan <macromorgan@hotmail.com>
Acked-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Acked-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Link: https://lore.kernel.org/r/20240821215456.962564-14-macroalpha82@gmail.com
[fix axp717_usb_power_desc.usb_types]
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
|
|
There is a spelling mistake in a dev_warn message. Fix it.
Signed-off-by: Colin Ian King <colin.i.king@gmail.com>
Acked-by: Chen-Yu Tsai <wens@csie.org>
Link: https://lore.kernel.org/r/20240828093447.271503-1-colin.i.king@gmail.com
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
|
|
Changing usb_types type from array to bitmap in the power_supply_desc
struct requires updating power-supply drivers living in different
subsystem, so it is handled via an immutable branch.
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
|
|
The bit_types array just hold a list of valid enum power_supply_usb_type
values which map to 0 - 9. This can easily be represented as a bitmap.
This reduces the size of struct power_supply_desc and further reduces
the data section size by drivers no longer needing to store the array.
This also unifies how usb_types are handled with charge_behaviours,
which allows power_supply_show_usb_type() to be removed.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Link: https://lore.kernel.org/r/20240831142039.28830-7-hdegoede@redhat.com
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
|
|
Move power_supply_show_enum_with_available() higher up in
the power_supply_sysfs.c file.
This is a preparation patch to avoid needing a forward declaration
when replacing power_supply_show_usb_type() with it later on.
This commit only moves the function, there are no changes to it.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Link: https://lore.kernel.org/r/20240831142039.28830-6-hdegoede@redhat.com
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
|
|
Turn power_supply_charge_behaviour_show() into a generic function for
showing enum values with their available (for writing) values shown
and the current value shown surrounded by sqaure-brackets like
the show() output for "usb_type" and "charge_behaviour".
This is a preparation patch for refactoring the "usb_type" property
handling to use a bitmask indicating available usb-types + this new
generic function.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Link: https://lore.kernel.org/r/20240831142039.28830-5-hdegoede@redhat.com
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
|
|
The "usb_type" property must be read-only for charger power-supply devices,
see: Documentation/ABI/testing/sysfs-class-power.
But the rt9467 driver allows writing 0/1 to it to disable/enable charging.
Other charger drivers use the "status" property for this and the rt9467
code also allows writing 0/1 to its "status" property and this does
the exact same thing as writing 0/1 to its "usb_type" property.
Drop write support for the "usb_type" property making it readonly to match
the ABI documentation. If userspace wants to disable/enable charging it
can use the "status" property for this.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Link: https://lore.kernel.org/r/20240831142039.28830-4-hdegoede@redhat.com
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
|
|
power_supply_sysfs.c accept wrrites of strings to "usb_type" for strings
values matching an entry in POWER_SUPPLY_USB_TYPE_TEXT[]. If such a
string value is written then the int value passed to ucs1002_set_property()
will be an enum power_supply_usb_type value.
Before this change ucs1002_set_usb_type() expected the value to be an index
into ucs1002_usb_types[]. Adjust ucs1002_set_usb_type() to use the enum
value directly so that writing string values works.
The list of supported types in ucs1002_usb_types[] is: PD, SDP, DCP, CDP.
The [POWER_SUPPLY_USB_TYPE_]SDP, DCP and CDP enum labels have a value of
1, 2 and 3. So userspace selecting SDP, DCP or CDP by writing 1, 2 or 3
will keep working. POWER_SUPPLY_USB_TYPE_PD which is mapped to the ucs1002
dedicated mode however has a value of 6. Before this change writing 0 would
select the dedicated mode. To preserve userspace API compatibility also map
POWER_SUPPLY_USB_TYPE_UNKNOWN (which is 0) to the dedicated mode.
Cc: Enric Balletbo Serra <enric.balletbo@collabora.com>
Cc: Andrey Smirnov <andrew.smirnov@gmail.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Link: https://lore.kernel.org/r/20240831142039.28830-3-hdegoede@redhat.com
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
|
|
According to Documentation/ABI/testing/sysfs-class-power the "usb_type"
property is Read-Only.
For power-supplies which consume USB power such as battery charger chips,
this is correct.
But the UCS1002 USB Port Power Controller driver which is a driver
for a chip which is a power-source for USB-A charging ports "usb_type"
is actually writable to configure the type of USB charger emulated
by the USB-A port.
Adjust the docs and the power_supply_sysfs.c code to adjust for this
new writeable use of "usb_type":
1. Update Documentation/ABI/testing/sysfs-class-power to document that
"usb_type" may be writable
2. Change the power_supply_attr type in power_supply_sysfs.c from
POWER_SUPPLY_ATTR() into POWER_SUPPLY_ENUM_ATTR() so that the various
usb_type string values from POWER_SUPPLY_TYPE_TEXT[] such as e.g.
"SDP" and "USB_PD" can be written to the "usb_type" attribute instead
of only accepting integer values.
Cc: Enric Balletbo Serra <enric.balletbo@collabora.com>
Cc: Andrey Smirnov <andrew.smirnov@gmail.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Link: https://lore.kernel.org/r/20240831142039.28830-2-hdegoede@redhat.com
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
|
|
ModelGauge m5 and device configuration values are stored in nonvolatile
memory to prevent data loss if the IC loses power. Add read support for
the nonvolatile memory on MAX1720X devices.
Signed-off-by: Dimitri Fedrau <dima.fedrau@gmail.com>
Link: https://lore.kernel.org/r/20240903063526.222890-1-dima.fedrau@gmail.com
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/brgl/linux
Pull power sequencing fix from Bartosz Golaszewski:
"A follow-up fix for the power sequencing subsystem. It turned out the
previous fix for this driver was incomplete and broke the WLAN support
on some platforms. This addresses the issue.
- set the direction of the wlan-enable GPIO to output after
requesting it as-is"
* tag 'pwrseq-fixes-for-v6.11-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/brgl/linux:
power: sequencing: qcom-wcn: set the wlan-enable GPIO to output
|
|
Commit a9aaf1ff88a8 ("power: sequencing: request the WLAN enable GPIO
as-is") broke WLAN on boards on which the wlan-enable GPIO enabling the
wifi module isn't in output mode by default. We need to set direction to
output while retaining the value that was already set to keep the ath
module on if it's already started.
Fixes: a9aaf1ff88a8 ("power: sequencing: request the WLAN enable GPIO as-is")
Link: https://lore.kernel.org/r/20240823115500.37280-1-brgl@bgdev.pl
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc
Pull ARM SoC fixes from Arnd Bergmann:
"There is a fairly large number of bug fixes for Qualcomm platforms,
most of them addressing issues with the devicetree files for the newly
added Snapdragon X1 based laptops to make them more reliable.
The Qualcomm driver changes address a few build-time issues as well as
runtime problems in the tzmem and scm firmware, the USB Type-C driver,
and the cmd-db and pmic_glink soc drivers.
The NXP i.MX usually gets a bunch of devicetree fixes that is
proportional to the number of supported machines. This includes both
warning fixes and correctness for the 64-bit i.MX9, i.MX8 and
layerscape platforms, as well as a single fix for a 32-bit i.MX6 based
board.
The other changes are the usual minor changes, including an update to
the MAINTAINERS file, an omap3 dts file and a SoC driver for mpfs
(risc-v)"
* tag 'arm-fixes-6.11-2' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc: (50 commits)
firmware: microchip: fix incorrect error report of programming:timeout on success
soc: qcom: pd-mapper: Fix singleton refcount
firmware: qcom: tzmem: disable sdm670 platform
soc: qcom: pmic_glink: Actually communicate when remote goes down
usb: typec: ucsi: Move unregister out of atomic section
soc: qcom: pmic_glink: Fix race during initialization
firmware: qcom: qseecom: remove unused functions
firmware: qcom: tzmem: fix virtual-to-physical address conversion
firmware: qcom: scm: Mark get_wq_ctx() as atomic call
arm64: dts: qcom: x1e80100: Fix Adreno SMMU global interrupt
arm64: dts: qcom: disable GPU on x1e80100 by default
arm64: dts: imx8mm-phygate: fix typo pinctrcl-0
arm64: dts: imx95: correct L3Cache cache-sets
arm64: dts: imx95: correct a55 power-domains
arm64: dts: freescale: imx93-tqma9352-mba93xxla: fix typo
arm64: dts: freescale: imx93-tqma9352: fix CMA alloc-ranges
ARM: dts: imx6dl-yapp43: Increase LED current to match the yapp4 HW design
arm64: dts: imx93: update default value for snps,clk-csr
arm64: dts: freescale: tqma9352: Fix watchdog reset
arm64: dts: imx8mp-beacon-kit: Fix Stereo Audio on WM8962
...
|
|
This struct is never modified, so mark it const.
Signed-off-by: Thomas Weißschuh <linux@weissschuh.net>
Link: https://lore.kernel.org/r/20240828-power-supply-const-psy_tzd_ops-v1-1-dc27176fda5b@weissschuh.net
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
|
|
https://git.kernel.org/pub/scm/linux/kernel/git/qcom/linux into arm/fixes
Qualcomm driver fixes for v6.11
This corrects the tzmem virt-to-phys conversion, which caused issues for
the uefisecapp implementation of EFI variable access. SDM670 is excluded
from tzmem usage due to reported issues.
The SCM get wait queue context call is corrected to be marked ATOMIC and
some dead code in qseecom, following the tzmem conversion, is removed.
The memory backing command DB is remapped writecombined, to avoid XPU
violations when Linux runs without the Qualcomm hypervisor.
Two compile fixes are added for pd-mapper, and the broken reference
count is corrected, to make pd-mapper deal with remoteprocs going away.
In pmic_glink a race condition where the client callbacks might be
called before we returned the client handle is corrected. The broken conditions
for when to signal that the firmware is going down is also corrected.
In the pmic_glink UCSI driver, the ucsi_unregister() is moved out of the
pdr callback, as this is being invoked in atomic context.
Konrad's email address is updated in MAINTAINERS, and related mailmap
entries are added.
* tag 'qcom-drivers-fixes-for-6.11' of https://git.kernel.org/pub/scm/linux/kernel/git/qcom/linux:
soc: qcom: pd-mapper: Fix singleton refcount
firmware: qcom: tzmem: disable sdm670 platform
soc: qcom: pmic_glink: Actually communicate when remote goes down
usb: typec: ucsi: Move unregister out of atomic section
soc: qcom: pmic_glink: Fix race during initialization
firmware: qcom: qseecom: remove unused functions
firmware: qcom: tzmem: fix virtual-to-physical address conversion
firmware: qcom: scm: Mark get_wq_ctx() as atomic call
MAINTAINERS: Update Konrad Dybcio's email address
mailmap: Add an entry for Konrad Dybcio
soc: qcom: pd-mapper: mark qcom_pdm_domains as __maybe_unused
soc: qcom: cmd-db: Map shared memory as WC, not WB
soc: qcom: pd-mapper: Depend on ARCH_QCOM || COMPILE_TEST
Link: https://lore.kernel.org/r/20240826145209.1646159-1-andersson@kernel.org
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
There may be other backup reset methods available, do not halt
here so that other reset methods can be tried.
Signed-off-by: Andrew Davis <afd@ti.com>
Reviewed-by: Dhruva Gole <d-gole@ti.com>
Acked-by: Florian Fainelli <florian.fainelli@broadcom.com>
Link: https://lore.kernel.org/r/20240610142836.168603-5-afd@ti.com
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
|
|
Function register_restart_handler() is deprecated. Using this new API
removes our need to keep and manage a struct notifier_block.
Signed-off-by: Andrew Davis <afd@ti.com>
Reviewed-by: Dhruva Gole <d-gole@ti.com>
Acked-by: Florian Fainelli <florian.fainelli@broadcom.com>
Link: https://lore.kernel.org/r/20240610142836.168603-4-afd@ti.com
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
|
|
Simplify probe by fetching the regmap and its arguments in one call.
Signed-off-by: Andrew Davis <afd@ti.com>
Reviewed-by: Dhruva Gole <d-gole@ti.com>
Acked-by: Florian Fainelli <florian.fainelli@broadcom.com>
Link: https://lore.kernel.org/r/20240610142836.168603-3-afd@ti.com
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
|
|
Use device_get_match_data() for finding the matching node and fetching
the match data all in one.
Signed-off-by: Andrew Davis <afd@ti.com>
Acked-by: Florian Fainelli <florian.fainelli@broadcom.com>
Link: https://lore.kernel.org/r/20240610142836.168603-2-afd@ti.com
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
|
|
The platform_driver_probe() helper is useful when the probe function
is in the _init section, that is not the case here. Use the normal
platform_driver_register() function.
Signed-off-by: Andrew Davis <afd@ti.com>
Reviewed-by: Dhruva Gole <d-gole@ti.com>
Acked-by: Florian Fainelli <florian.fainelli@broadcom.com>
Link: https://lore.kernel.org/r/20240610142836.168603-1-afd@ti.com
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
|
|
The OCP board used a BlueField's GPIO pin for entering
low power mode. That board was not commercialized and
has been dropped from production so all its code is unused.
The new hardware requirement is to trigger a graceful shutdown
when that GPIO pin is toggled. So replace the unused low power
mode with a graceful shutdown.
Signed-off-by: Asmaa Mnebhi <asmaa@nvidia.com>
Reviewed-by: David Thompson <davthompson@nvidia.com>
Link: https://lore.kernel.org/r/20240611134327.30975-1-asmaa@nvidia.com
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
|
|
Replace a comma between expression statements by a semicolon.
Signed-off-by: Chen Ni <nichen@iscas.ac.cn>
Link: https://lore.kernel.org/r/20240710032023.2003742-1-nichen@iscas.ac.cn
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
|
|
There are two charger current limit registers:
- Fast charge current limit (which controls current going from the
charger to the battery);
- CHGIN input current limit (which controls current going into the
charger through the cable).
Add the necessary functions to retrieve the CHGIN input limit (from CHARGER
regulator) and maximum fast charge current values, and expose them as power
supply properties.
Tested-by: Henrik Grimler <henrik@grimler.se>
Signed-off-by: Artur Weber <aweber.kernel@gmail.com>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Link: https://lore.kernel.org/r/20240816-max77693-charger-extcon-v4-3-050a0a9bfea0@gmail.com
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
|
|
Commit 223a3b82834f ("power: supply: max17042_battery: use VFSOC for
capacity when no rsns") made it so that capacity on systems without
current sensing would be read from VFSOC instead of RepSOC. However,
the SOC threshold calculation still read RepSOC to get the SOC
regardless of the current sensing option state.
Fix this by applying the same conditional to determine which register
should be read.
This also seems to be the intended behavior as per the datasheet - SOC
alert config value in MiscCFG on setups without current sensing is set
to a value of 0b11, indicating SOC alerts being generated based on
VFSOC, instead of 0b00 which indicates SOC alerts being generated based
on RepSOC.
This fixes an issue on the Galaxy S3/Midas boards, where the alert
interrupt would be constantly retriggered, causing high CPU usage
on idle (around ~12%-15%).
Fixes: e5f3872d2044 ("max17042: Add support for signalling change in SOC")
Signed-off-by: Artur Weber <aweber.kernel@gmail.com>
Reviewed-by: Henrik Grimler <henrik@grimler.se>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Link: https://lore.kernel.org/r/20240817-max17042-soc-threshold-fix-v1-1-72b45899c3cc@gmail.com
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
|
|
Allow users to specify a maximum input current for the device. Some
devices allow up to 3.25A of input current (such as the AXP717), which
may be too much for some implementations.
Signed-off-by: Chris Morgan <macromorgan@hotmail.com>
Acked-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Link: https://lore.kernel.org/r/20240821215456.962564-7-macroalpha82@gmail.com
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
|
