| Age | Commit message (Collapse) | Author |
|---|
|
Do not imply that some of the generic headers may be always included.
Instead, include explicitly what we are direct user of.
While at it, sort headers alphabetically.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Mika Westerberg <mika.westerberg@linux.intel.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl
Pull pin control updates from Linus Walleij:
"Outside the pinctrl driver and DT bindings we hit some Arm DT files,
patched by the maintainers.
Other than that it is business as usual.
Core changes:
- Add PINCTRL_PINGROUP() helper macro (and use it in the AMD driver).
New drivers:
- Intel Meteor Lake support.
- Reneasas RZ/V2M and r8a779g0 (R-Car V4H).
- AXP209 variants AXP221, AXP223 and AXP809.
- Qualcomm MSM8909, PM8226, PMP8074 and SM6375.
- Allwinner D1.
Improvements:
- Proper pin multiplexing in the AMD driver.
- Mediatek MT8192 can use generic drive strength and pin bias, then
fixes on top plus some I2C pin group fixes.
- Have the Allwinner Sunplus SP7021 use the generic DT schema and
make interrupts optional.
- Handle Qualcomm SC7280 ADSP.
- Handle Qualcomm MSM8916 CAMSS GP clock muxing.
- High impedance bias on ZynqMP.
- Serialize StarFive access to MMIO.
- Immutable gpiochip for BCM2835, Ingenic, Qualcomm SPMI GPIO"
* tag 'pinctrl-v6.0-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl: (117 commits)
dt-bindings: pinctrl: qcom,pmic-gpio: add PM8226 constraints
pinctrl: qcom: Make PINCTRL_SM8450 depend on PINCTRL_MSM
pinctrl: qcom: sm8250: Fix PDC map
pinctrl: amd: Fix an unused variable
dt-bindings: pinctrl: mt8186: Add and use drive-strength-microamp
dt-bindings: pinctrl: mt8186: Add gpio-line-names property
ARM: dts: imxrt1170-pinfunc: Add pinctrl binding header
pinctrl: amd: Use unicode for debugfs output
pinctrl: amd: Fix newline declaration in debugfs output
pinctrl: at91: Fix typo 'the the' in comment
dt-bindings: pinctrl: st,stm32: Correct 'resets' property name
pinctrl: mvebu: Missing a blank line after declarations.
pinctrl: qcom: Add SM6375 TLMM driver
dt-bindings: pinctrl: Add DT schema for SM6375 TLMM
dt-bindings: pinctrl: mt8195: Use drive-strength-microamp in examples
Revert "pinctrl: qcom: spmi-gpio: make the irqchip immutable"
pinctrl: imx93: Add MODULE_DEVICE_TABLE()
pinctrl: sunxi: Add driver for Allwinner D1
pinctrl: sunxi: Make some layout parameters dynamic
pinctrl: sunxi: Refactor register/offset calculation
...
|
|
In some cases we may get a platform device that has ACPI companion
which is different to the pin control described in the ACPI tables.
This is primarily happens when device is instantiated by board file.
In order to allow this device being enumerated, refactor
intel_pinctrl_get_soc_data() to check the matching data instead of
ACPI companion.
Reported-by: Henning Schild <henning.schild@siemens.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Tested-by: Henning Schild <henning.schild@siemens.com>
Acked-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Lee Jones <lee@kernel.org>
|
|
Since struct intel_pingroup got a new member, switch the driver to use it.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
|
|
Kernel doc validator is not happy:
pinctrl-intel.c:865: warning: No description found for return value of 'intel_gpio_to_pin'
pinctrl-intel.c:904: warning: No description found for return value of 'intel_pin_to_gpio'
2 warnings
Add return sections to the kernel documentation of the above mentioned
functions.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
|
|
Since recently, the kernel is nagging about mutable irq_chips:
"not an immutable chip, please consider fixing it!"
Drop the unneeded copy, flag it as IRQCHIP_IMMUTABLE, add the new
helper functions and call the appropriate gpiolib functions.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
|
|
The commit af7e3eeb84e2 ("pinctrl: intel: Disable input and output buffer
when switching to GPIO") hadn't taken into account an update of the IRQ
flags scenario.
When updating the IRQ flags on the preconfigured line the ->irq_set_type()
is called again. In such case the sequential Rx buffer configuration
changes may trigger a falling or rising edge interrupt that may lead,
on some platforms, to an undesired event.
This may happen because each of intel_gpio_set_gpio_mode() and
__intel_gpio_set_direction() updates the pad configuration with a different
value of the GPIORXDIS bit. Notable, that the intel_gpio_set_gpio_mode() is
called only for the pads that are configured as an input. Due to this fact,
integrate the logic of __intel_gpio_set_direction() call into the
intel_gpio_set_gpio_mode() so that the Rx buffer won't be disabled and
immediately re-enabled.
Fixes: af7e3eeb84e2 ("pinctrl: intel: Disable input and output buffer when switching to GPIO")
Reported-by: Kane Chen <kane.chen@intel.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Tested-by: Grace Kao <grace.kao@intel.com>
|
|
ASUS Chromebook C223 with Celeron N3350 crashes sometimes during
cold booot. Inspection of the kernel log showed that it gets into
an inifite loop logging the following message:
->handle_irq(): 000000009cdb51e8, handle_bad_irq+0x0/0x251
->irq_data.chip(): 000000005ec212a7, 0xffffa043009d8e7
->action(): 00000
IRQ_NOPROBE set
unexpected IRQ trap at vector 7c
The issue happens during cold boot but only if cold boot happens
at most several dozen seconds after Chromebook is powered off. For
longer intervals between power off and power on (cold boot) the issue
does not reproduce. The unexpected interrupt is sourced from INT3452
GPIO pin which is used for SD card detect. Investigation relevealed
that when the interval between power off and power on (cold boot)
is less than several dozen seconds then values of INT3452 GPIO interrupt
enable and interrupt pending registers survive power off and power
on sequence and interrupt for SD card detect pin is enabled and pending
during probe of SD controller which causes the unexpected IRQ message.
"Intel Pentium and Celeron Processor N- and J- Series" volume 3 doc
mentions that GPIO interrupt enable and status registers default
value is 0x0.
The fix clears INT3452 GPIO interrupt enabled and interrupt pending
registers in its probe function.
Fixes: 7981c0015af2 ("pinctrl: intel: Add Intel Sunrisepoint pin controller and GPIO support")
Signed-off-by: Łukasz Bartosik <lb@semihalf.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl
Pull pin control updates from Linus Walleij:
"There is a lot going on!
Core changes:
- A semantic change to handle pinmux and pinconf in explicit order
while up until now we depended on the semantic order in the device
tree. The device tree is a functional programming language and does
not imply any order, so the right thing is for the pin control core
to provide these semantics.
- Add a new pinmux-select debugfs file which makes it possible to go
in and select functions for a pin manually (iteratively, at the
prompt) for debugging purposes.
- Fixes to gpio regmap handling for a new pin control driver making
use of regmap-gpio.
- Use octal permissions on debugfs files.
New drivers:
- A massive rewrite of the former custom pin control driver for MIPS
Broadcom devices to instead use the pin control subsystem. New pin
control drivers for BCM6345, BCM6328, BCM6358, BCM6362, BCM6368,
BCM63268 and BCM6318 SoC variants are implemented.
- Support for PM8350, PM8350B, PM8350C, PMK8350, PMR735A and PMR735B
in the Qualcomm PMIC GPIO driver. Also the two GPIOs on PM8008 are
supported.
- Support for the Rockchip RK3568/RK3566 pin controller.
- Support for Ingenic JZ4730, JZ4750, JZ4755, JZ4775 and X2000.
- Support for Mediatek MTK8195.
- Add a new Xilinx ZynqMP pin control driver.
Driver improvements and non-urgent fixes:
- Modularization and improvements of the Rockchip drivers.
- Some new pins added to the description of new Renesas SoCs.
- Clarifications of the GPIO base calculation in the Intel driver.
- Fix the function names for the MPP54 and MPP55 pins in the Armada
CP110 pin controller.
- GPIO wakeup interrupt map for Qualcomm SC7280 and SM8350.
- Support for ACPI probing of the Qualcomm SC8180x.
- Fix interrupt clear status on rockchip
- Fix some missing pins on the Ingenic JZ4770, some semantic fixes
for the behaviour of the Ingenic pin controller. Add DMIC pins for
JZ4780, X1000, X1500 and X1830.
- A slew of janitorial like of_node_put() calls"
* tag 'pinctrl-v5.13-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl: (99 commits)
pinctrl: Add Xilinx ZynqMP pinctrl driver support
firmware: xilinx: Add pinctrl support
pinctrl: rockchip: do coding style for mux route struct
pinctrl: Add PIN_CONFIG_MODE_PWM to enum pin_config_param
pinctrl: Introduce MODE group in enum pin_config_param
pinctrl: Keep enum pin_config_param ordered by name
dt-bindings: pinctrl: Add binding for ZynqMP pinctrl driver
pinctrl: core: Fix kernel doc string for pin_get_name()
pinctrl: mediatek: use spin lock in mtk_rmw
pinctrl: add drive for I2C related pins on MT8195
pinctrl: add pinctrl driver on mt8195
dt-bindings: pinctrl: mt8195: add pinctrl file and binding document
pinctrl: Ingenic: Add pinctrl driver for X2000.
pinctrl: Ingenic: Add pinctrl driver for JZ4775.
pinctrl: Ingenic: Add pinctrl driver for JZ4755.
pinctrl: Ingenic: Add pinctrl driver for JZ4750.
pinctrl: Ingenic: Add pinctrl driver for JZ4730.
dt-bindings: pinctrl: Add bindings for new Ingenic SoCs.
pinctrl: Ingenic: Reformat the code.
pinctrl: Ingenic: Add DMIC pins support for Ingenic SoCs.
...
|
|
Use the value read from the REVID register in order to check for the
presence of the device. A read of all ones is treated as if the device
is not present, and hence probing is ended.
This fixes an issue when running as a Xen PVH dom0, where the ACPI
DSDT table is provided unmodified to dom0 and hence contains the
pinctrl devices, but the MMIO region(s) containing the device
registers might not be mapped in the guest physical memory map if such
region(s) are not exposed on a PCI device BAR or marked as reserved in
the host memory map.
Fixes: 91d898e51e60 ("pinctrl: intel: Convert capability list to features")
Suggested-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Roger Pau Monné <roger.pau@citrix.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
|
|
In IRQ handler interrupts are already disabled, hence no need
to repeat it. Even in the threaded case, which is disabled here,
it is not a problem because IRQ framework serializes descriptor
handling. Remove disabling IRQ part in the handler.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
|
|
During the split of intel_pinctrl_add_padgroups(), the _by_size() variant
missed the GPIO base calculations and hence made unable to retrieve proper
GPIO number.
Assign the gpio_base explicitly in _by_size() variant.
While at it, differentiate NOMAP case with the rest in _by_gpps() variant.
Fixes: 036e126c72eb ("pinctrl: intel: Split intel_pinctrl_add_padgroups() for better maintenance")
Reported-and-tested-by: Maximilian Luz <luzmaximilian@gmail.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
|
|
Communities can have features provided in the capability list.
Traverse the list and convert to respective features.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
|
|
None of the drivers is overriding features. Remove unnecessary check.
While here, rename rev to value to make easier further development.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
|
|
Currently the intel_pinctrl_add_padgroups() is twisted a bit due to
a different nature of the pin control hardware implementations. Thus,
its maintenance is a bit hard. Besides that some pieces of code
are run on all hardware and make this code slightly inefficient,
and moreover, validation for one case is done in a wrong time in a flow
which makes it even slower.
Split intel_pinctrl_add_padgroups() to two functions, one per hardware
implementation, for better maintenance and readability.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
|
|
Mistakenly the buffers (input and output) become enabled together for a short
period of time during GPIO request. This is problematic, because instead of
initial motive to disable them in the commit af7e3eeb84e2
("pinctrl: intel: Disable input and output buffer when switching to GPIO"),
the driven value on the pin, which might be used as an IRQ line, brings
firmwares of some touch pads to an awkward state that needs a full power off
to recover. Fix this, as stated in the culprit commit, by disabling the buffers.
Fixes: af7e3eeb84e2 ("pinctrl: intel: Disable input and output buffer when switching to GPIO")
BugLink: https://bugzilla.kernel.org/show_bug.cgi?id=210497
Reported-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Tested-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Tested-by: Kai-Heng Feng <kai.heng.feng@canonical.com>
Link: https://lore.kernel.org/r/20201208182403.40435-1-andriy.shevchenko@linux.intel.com
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
When GPIO library asks pin control to set the bias, it doesn't pass
any value of it and argument is considered boolean (and this is true
for ACPI GpioIo() / GpioInt() resources, by the way). Thus, individual
drivers must behave well, when they got the resistance value of 1 Ohm,
i.e. transforming it to sane default.
In case of Intel pin control hardware the 5 kOhm sounds plausible
because on one hand it's a minimum of resistors present in all
hardware generations and at the same time it's high enough to minimize
leakage current (will be only 200 uA with the above choice).
Fixes: e57725eabf87 ("pinctrl: intel: Add support for hardware debouncer")
Reported-by: Jamie McClymont <jamie@kwiius.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
|
|
2 kOhm bias was never an option in Intel GPIO hardware, the available
matrix is:
000 none
001 1 kOhm (if available)
010 5 kOhm
100 20 kOhm
As easy to get the 3 resistors are gated separately and according to
parallel circuits calculations we may get combinations of the above where
the result is always strictly less than minimal resistance. Hence,
additional values can be:
011 ~833.3 Ohm
101 ~952.4 Ohm
110 ~4 kOhm
111 ~800 Ohm
That said, convert TERM definitions to be the bit masks to reflect the above.
While at it, enable the same setting for pull down case.
Fixes: 7981c0015af2 ("pinctrl: intel: Add Intel Sunrisepoint pin controller and GPIO support")
Cc: Jamie McClymont <jamie@kwiius.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
|
|
intel_pinctrl_get_soc_data() helper can be used in few driver instead of
open-coded variants. Thus, extract it as a standalone API.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
|
|
Make use of for_each_requested_gpio_in_range() instead of home grown analogue.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
|
|
Protect IO in intel_gpio_get_direction(), intel_gpio_community_irq_handler(),
intel_config_get_debounce() and intel_config_get_pull() by lock. Even for
simple readl() we better serialize IO to avoid potential problems.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
|
|
Split intel_config_get() to three functions, i.e. intel_config_get() and
two helpers intel_config_get_pull() and intel_config_get_debounce() to be
symmetrical with intel_config_set*().
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
|
|
Drop the only label in the code, i.e. in intel_config_set_debounce(),
for consistency with the rest. In entire driver we use multipoint
return.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
|
|
In a code like
if (...) {
...
goto label;
} else {
...
}
the 'else' keyword is redundant. Get rid of it for better readability.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
|
|
Instead of using bitwise operations against returned values,
which is a bit fragile, convert IRQ handler to count amount of
GPIO groups, where at least one interrupt happened, and convert
it to returned value by IRQ_RETVAL() macro.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
|
|
In some cases lock covers unneeded calls and operations.
Reduce scope of the lock in such cases.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
|
|
It's possible scenario that pin has been in different mode, while
the respective GPIO register has a leftover output buffer enabled.
In such case when we request GPIO it will switch to GPIO mode, and
thus to output with unknown value, followed by switching to input
mode. This can produce a glitch on the pin.
Disable input and output buffer when switching to GPIO to avoid
potential glitches.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
|
|
In some cases not the first group would like to have GPIO base to be 0.
It's not possible right now due to 0 has special meaning already. Thus,
introduce a new flag to allow drivers to force GPIO base to be 0 on
a certain group. It's assumed that it can be only one group per device
with such flag enabled.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
|
|
Few drivers are using the same flag to tell Intel pin control core
how to interpret GPIO base.
Provide a generic flags so all drivers can use.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
|
|
We need to convert all old gpio irqchips to pass the irqchip
setup along when adding the gpio_chip. For more info see
drivers/gpio/TODO.
For chained irqchips this is a pretty straight-forward conversion.
Cc: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
|
|
When IRQ chip is instantiated via GPIO library flow, the few functions,
in particular the ACPI event registration mechanism, on some of ACPI based
platforms expect that the pin ranges are initialized to that point.
Add GPIO <-> pin mapping ranges via callback in the GPIO library flow.
Cc: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
|
|
There are few drivers for Intel SoC GPIO which may utilize
the same data structure to describe this IP.
Share struct intel_pinctrl for wider user.
Acked-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
|
|
Use new GPIO_LINE_DIRECTION_IN and GPIO_LINE_DIRECTION_OUT when
returning GPIO direction to GPIO framework.
Signed-off-by: Matti Vaittinen <matti.vaittinen@fi.rohmeurope.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
|
|
We converted 'unsigned' type to be 'unsigned int' in the driver,
but there are couple of leftovers. So, finish the task now.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
|
|
We can restore only values that had been changed and do not spam kernel log
with unnecessary messages. Convert intel_gpio_update_pad_mode() to a helper
function that will be used across few callers.
Suggested-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
|
|
Since we didn't get any new reports from users about wrong settings
of pad ownership, there is no point to spam kernel log with it. Thus,
drop level from warning to debug.
Also, modify format to be in align with the rest restore helpers.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
|
|
Refactor restoring GPI_IE registers by using an introduced helper.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
|
|
Refactor restoring HOSTSW_OWN registers by using an introduced helper.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
|
|
Deduplicate restoring PADCFGx registers by using a common helper.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
|
|
When consumer requests a pin, in order to be on the safest side,
we switch it first to GPIO mode followed by immediate transition
to the input state. Due to posted writes it's luckily to be a single
I/O transaction.
However, if firmware or boot loader already configures the pin
to the GPIO mode, user expects no glitches for the requested pin.
We may check if the pin is pre-configured and leave it as is
till the actual consumer toggles its state to avoid glitches.
Fixes: 7981c0015af2 ("pinctrl: intel: Add Intel Sunrisepoint pin controller and GPIO support")
Depends-on: f5a26acf0162 ("pinctrl: intel: Initialize GPIO properly when used through irqchip")
Cc: stable@vger.kernel.org
Cc: fei.yang@intel.com
Reported-by: Oliver Barta <oliver.barta@aptiv.com>
Reported-by: Malin Jonsson <malin.jonsson@ericsson.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
|
|
Keeping the IRQ chip definition static shares it with multiple instances of
the GPIO chip in the system. This is bad and now we get this warning from
GPIO library:
"detected irqchip that is shared with multiple gpiochips: please fix the driver."
Hence, move the IRQ chip definition from being driver static into the struct
intel_pinctrl. So a unique IRQ chip is used for each GPIO chip instance.
Fixes: ee1a6ca43dba ("pinctrl: intel: Add Intel Broxton pin controller support")
Depends-on: 5ff56b015e85 ("pinctrl: intel: Disable GPIO pin interrupts in suspend")
Reported-by: Federico Ricchiuto <fed.ricchiuto@gmail.com>
Suggested-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
|
|
The intel_pin_to_gpio() function is only called by the
PM support functions and causes a warning when those are disabled:
drivers/pinctrl/intel/pinctrl-intel.c:841:12: error: unused function 'intel_pin_to_gpio' [-Werror,-Wunused-function]
Mark it __maybe_unused to suppress the warning.
Suggested-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: Chris Chiu <chiu@endlessm.com>
Acked-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
|
|
On Asus X571GT, GPIO 297 is configured as an interrupt and serves
for the touchpad. The touchpad will report input events much less
than expected after S3 suspend/resume, which results in extremely
slow cursor movement. However, the number of interrupts observed
from /proc/interrupts increases much more than expected even no
touching touchpad.
This is due to the value of PADCFG0 of PIN 225 for the interrupt
has been changed from 0x80800102 to 0x80100102. The GPIROUTIOXAPIC
is toggled on which results in the spurious interrupts. The PADCFG0
of PIN 225 is expected to be saved during suspend, but the 297 is
saved instead because the gpiochip_line_is_irq() expect the GPIO
offset but what's really passed to it is PIN number. In this case,
the /sys/kernel/debug/pinctrl/INT3450:00/gpio-ranges shows
288: INT3450:00 GPIOS [436 - 459] PINS [216 - 239]
So gpiochip_line_is_irq() returns true for GPIO offset 297, the
suspend routine spuriously saves the content for PIN 297 which
we expect to save for PIN 225.
This commit maps the PIN number to GPIO offset first in the
intel_pinctrl_should_save() to make sure the values for the
specific PINs can be correctly saved and then restored.
Fixes: c538b9436751 ("pinctrl: intel: Only restore pins that are used by the driver")
Signed-off-by: Chris Chiu <chiu@endlessm.com>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
|
|
Some firmwares would like to protect pads from being modified by OS
and at the same time provide them to OS as a resource. So, the driver
in such circumstances may request pad and may not change its state.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
|
|
We don't need dev_err() messages when platform_get_irq() fails now that
platform_get_irq() prints an error message itself when something goes
wrong. Let's remove these prints with a simple semantic patch.
// <smpl>
@@
expression ret;
struct platform_device *E;
@@
ret =
(
platform_get_irq(E, ...)
|
platform_get_irq_byname(E, ...)
);
if ( \( ret < 0 \| ret <= 0 \) )
{
(
-if (ret != -EPROBE_DEFER)
-{ ...
-dev_err(...);
-... }
|
...
-dev_err(...);
)
...
}
// </smpl>
While we're here, remove braces on if statements that only have one
statement (manually).
Cc: Linus Walleij <linus.walleij@linaro.org>
Cc: linux-gpio@vger.kernel.org
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Mika Westerberg <mika.westerberg@linux.intel.com>
Cc: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Stephen Boyd <swboyd@chromium.org>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
|
|
Replace hard coded constants with self-explanatory names, i.e.
use NSEC_PER_USEC for debounce calculus.
While here, add a unit suffix to debounce period constant.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
|
|
Since some of the GPIO controllers use different Interrupt Status offset,
it make sense to provide it explicitly in the drivers.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
|
|
There is more generic and simpler validation just against the nregs.
Using it allows to drop customization from the intel_get_padcfg().
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
|
|
There is no need to duplicate the check which is done in the common
intel_pinctrl_probe().
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
|
|
Use the new helper that wraps the calls to platform_get_resource()
and devm_ioremap_resource() together.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
|
