summaryrefslogtreecommitdiff
path: root/drivers/pci
AgeCommit message (Collapse)Author
2024-07-09PCI: layerscape-ep: Use the generic dw_pcie_ep_linkdown() API to handle Link ↵Manivannan Sadhasivam
Down event Now that dw_pcie_ep_linkdown() is available, use it. This also handles the reinitialization of DWC non-sticky registers in addition to sending the notification to EPF drivers. Closes: https://lore.kernel.org/linux-pci/20240528195539.GA458945@bhelgaas Link: https://lore.kernel.org/linux-pci/20240606-pci-deinit-v1-5-4395534520dc@linaro.org Reported-by: Bjorn Helgaas <helgaas@kernel.org> Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org> Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org> Signed-off-by: Bjorn Helgaas <bhelgaas@google.com> Reviewed-by: Frank Li <Frank.Li@nxp.com> Reviewed-by: Niklas Cassel <cassel@kernel.org>
2024-07-09PCI: qcom-ep: Use the generic dw_pcie_ep_linkdown() API to handle Link Down ↵Manivannan Sadhasivam
event Now that the generic dw_pcie_ep_linkdown() API is available, use it. This also handles the reinitialization of DWC non-sticky registers in addition to sending the notification to EPF drivers. Link: https://lore.kernel.org/linux-pci/20240430-pci-epf-rework-v4-9-22832d0d456f@linaro.org Tested-by: Niklas Cassel <cassel@kernel.org> Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org> Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org> Signed-off-by: Bjorn Helgaas <bhelgaas@google.com> Reviewed-by: Niklas Cassel <cassel@kernel.org>
2024-07-09PCI: dwc: ep: Remove dw_pcie_ep_init_notify() wrapperManivannan Sadhasivam
Currently dw_pcie_ep_init_notify() wrapper just calls pci_epc_init_notify() directly, so this wrapper provides no benefit to the glue drivers. Remove it and call pci_epc_init_notify() directly from glue drivers. Suggested-by: Bjorn Helgaas <helgaas@kernel.org> Link: https://lore.kernel.org/linux-pci/20240606-pci-deinit-v1-1-4395534520dc@linaro.org Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org> Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org> Signed-off-by: Bjorn Helgaas <bhelgaas@google.com> Reviewed-by: Siddharth Vadapalli <s-vadapalli@ti.com> Reviewed-by: Frank Li <Frank.Li@nxp.com> Reviewed-by: Niklas Cassel <cassel@kernel.org>
2024-07-09PCI: dwc: ep: Add a generic dw_pcie_ep_linkdown() API to handle Link Down eventManivannan Sadhasivam
Per PCIe r6.0, sec 5.2, a Link Down event can happen under any of the following circumstances: 1. Fundamental/Hot reset 2. Link disable transmission by upstream component 3. Moving from L2/L3 to L0 In those cases, Link Down causes some non-sticky DWC registers to lose the state (like REBAR, etc.), so drivers need to reinitialize them to function properly once the link comes back again. This is not a problem for drivers supporting PERST# IRQ, since they can reinitialize the registers in the PERST# IRQ callback. But for the drivers not supporting PERST#, there is no way they can reinitialize the registers other than relying on Link Down IRQ received when the link goes down. So add a DWC generic API dw_pcie_ep_linkdown() that reinitializes the non-sticky registers and also notifies the EPF drivers about link going down. This API can also be used by the drivers supporting PERST# to handle the scenario (2) mentioned above. NOTE: For the sake of code organization, move the dw_pcie_ep_linkup() definition just above dw_pcie_ep_linkdown(). Link: https://lore.kernel.org/linux-pci/20240430-pci-epf-rework-v4-8-22832d0d456f@linaro.org Tested-by: Niklas Cassel <cassel@kernel.org> Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org> Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org> [bhelgaas: update spec citation] Signed-off-by: Bjorn Helgaas <bhelgaas@google.com> Reviewed-by: Niklas Cassel <cassel@kernel.org>
2024-07-09PCI: dwc: Add generic MSG TLP support for sending PME_Turn_Off when system ↵Frank Li
suspend Instead of relying on the vendor specific implementations to send the PME_Turn_Off message, introduce a generic way of sending the message using the MSG TLP. This is achieved by reserving a region for MSG TLP of size 'pci->region_align', at the end of the first IORESOURCE_MEM window of the host bridge. And then sending the PME_Turn_Off message during system suspend with the help of iATU. The reason for reserving the MSG TLP region at the end of the IORESOURCE_MEM is to avoid generating holes in between, because when the region is allocated using allocate_resource(), memory will be allocated from the start of the window. Later, if memory gets allocated for an endpoint of size bigger than 'region_align', there will be a hole between MSG TLP region and endpoint memory. This generic implementation is optional for the glue drivers and can be overridden by a custom 'pme_turn_off' callback. Link: https://lore.kernel.org/linux-pci/20240418-pme_msg-v8-5-a54265c39742@nxp.com Signed-off-by: Frank Li <Frank.Li@nxp.com> Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org> Signed-off-by: Bjorn Helgaas <bhelgaas@google.com> Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
2024-07-09PCI: Add PCIE_MSG_CODE_PME_TURN_OFF message macroFrank Li
Add PCIE_MSG_CODE_PME_TURN_OFF macros to enable a PCIe host driver to send PME_Turn_Off messages. Link: https://lore.kernel.org/linux-pci/20240418-pme_msg-v8-4-a54265c39742@nxp.com Signed-off-by: Frank Li <Frank.Li@nxp.com> Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org> Signed-off-by: Bjorn Helgaas <bhelgaas@google.com> Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
2024-07-09PCI: Add PCIE_MSG_CODE_ASSERT_INTx message macrosYoshihiro Shimoda
Add "Message Routing" and "INTx Mechanism Messages" macros to enable a PCIe driver to send messages for INTx Interrupt Signaling. Values from PCIe r6.1, sec 2.2.8 and 2.2.8.1. Link: https://lore.kernel.org/linux-pci/20240418-pme_msg-v8-1-a54265c39742@nxp.com Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com> Signed-off-by: Frank Li <Frank.Li@nxp.com> Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org> Signed-off-by: Bjorn Helgaas <bhelgaas@google.com> Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org> Reviewed-by: Serge Semin <fancer.lancer@gmail.com>
2024-07-09PCI: dwc: Add outbound MSG TLPs supportYoshihiro Shimoda
Add "code" and "routing" into struct dw_pcie_ob_atu_cfg for triggering INTx IRQs by iATU in the PCIe endpoint mode in near the future. PCIE_ATU_INHIBIT_PAYLOAD is set to issue TLP type of Msg instead of MsgD. This implementation supports the data-less messages only for now. Link: https://lore.kernel.org/linux-pci/20240418-pme_msg-v8-3-a54265c39742@nxp.com Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com> Signed-off-by: Frank Li <Frank.Li@nxp.com> Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org> Signed-off-by: Bjorn Helgaas <bhelgaas@google.com> Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org> Reviewed-by: Serge Semin <fancer.lancer@gmail.com>
2024-07-09PCI: dwc: Consolidate args of dw_pcie_prog_outbound_atu() into a structureYoshihiro Shimoda
This is a preparation before adding the Msg-type outbound iATU mapping. The respective update will require two more arguments added to __dw_pcie_prog_outbound_atu(). That will make the already complicated function prototype even more hard to comprehend accepting _eight_ arguments. To prevent that and keep the code more-or-less readable, move all the outbound iATU-related arguments to a new config structure: struct dw_pcie_ob_atu_cfg, and pass a pointer to dw_pcie_prog_outbound_atu(). The structure should be locally defined and populated with the outbound iATU settings implied by the caller context. As a result of this change there is no longer need in having the two distinctive methods for the Host and Endpoint outbound iATU setups since the code can directly call the dw_pcie_prog_outbound_atu() method with the config structure populated, so drop dw_pcie_prog_ep_outbound_atu(). [kwilczynski: commit log] Link: https://lore.kernel.org/linux-pci/20240418-pme_msg-v8-2-a54265c39742@nxp.com Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com> Signed-off-by: Frank Li <Frank.Li@nxp.com> Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org> Signed-off-by: Bjorn Helgaas <bhelgaas@google.com> Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org> Reviewed-by: Serge Semin <fancer.lancer@gmail.com>
2024-07-09PCI: dwc: Fix index 0 incorrectly being interpreted as a free ATU slotFrank Li
When PERST# assert and deassert happens on the PERST# supported platforms, both iATU0 and iATU6 will map inbound window to BAR0. DMA will access the area that was previously allocated (iATU0) for BAR0, instead of the new area (iATU6) for BAR0. Right now, this isn't an issue because both iATU0 and iATU6 should translate inbound accesses to BAR0 to the same allocated memory area. However, having two separate inbound mappings for the same BAR is a disaster waiting to happen. The mappings between PCI BAR and iATU inbound window are maintained in the dw_pcie_ep::bar_to_atu[] array. While allocating a new inbound iATU map for a BAR, dw_pcie_ep_inbound_atu() API checks for the availability of the existing mapping in the array and if it is not found (i.e., value in the array indexed by the BAR is found to be 0), it allocates a new map value using find_first_zero_bit(). The issue is the existing logic failed to consider the fact that the map value '0' is a valid value for BAR0, so find_first_zero_bit() will return '0' as the map value for BAR0 (note that it returns the first zero bit position). Due to this, when PERST# assert + deassert happens on the PERST# supported platforms, the inbound window allocation restarts from BAR0 and the existing logic to find the BAR mapping will return '6' for BAR0 instead of '0' due to the fact that it considers '0' as an invalid map value. Fix this issue by always incrementing the map value before assigning to bar_to_atu[] array and then decrementing it while fetching. This will make sure that the map value '0' always represents the invalid mapping." Fixes: 4284c88fff0e ("PCI: designware-ep: Allow pci_epc_set_bar() update inbound map address") Closes: https://lore.kernel.org/linux-pci/ZXsRp+Lzg3x%2Fnhk3@x1-carbon/ Link: https://lore.kernel.org/linux-pci/20240412160841.925927-1-Frank.Li@nxp.com Reported-by: Niklas Cassel <Niklas.Cassel@wdc.com> Tested-by: Niklas Cassel <niklas.cassel@wdc.com> Signed-off-by: Frank Li <Frank.Li@nxp.com> Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org> Signed-off-by: Bjorn Helgaas <bhelgaas@google.com> Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org> Reviewed-by: Niklas Cassel <niklas.cassel@wdc.com>
2024-07-09PCI: dwc: Use msleep() in dw_pcie_wait_for_link()Konrad Dybcio
According to [1], msleep should be used for large sleeps, such as the 100-ish ms one in this function. Comply with the guide and use it. [1] https://docs.kernel.org/timers/timers-howto.html [kwilczynski: commit log] Link: https://lore.kernel.org/linux-pci/20240215-topic-pci_sleep-v2-1-79334884546b@linaro.org Signed-off-by: Konrad Dybcio <konrad.dybcio@linaro.org> Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org> Signed-off-by: Bjorn Helgaas <bhelgaas@google.com> Reviewed-by: Johan Hovold <johan+linaro@kernel.org> Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
2024-07-04PCI: endpoint: Fix error handling in epf_ntb_epc_cleanup()Dan Carpenter
There are two issues related to epf_ntb_epc_cleanup(): 1) It should call epf_ntb_config_sspad_bar_clear() 2) The epf_ntb_bind() function should call epf_ntb_epc_cleanup() to cleanup. I also changed the ordering a bit. Unwinding should be done in the mirror order from how they are allocated. Fixes: e35f56bb0330 ("PCI: endpoint: Support NTB transfer between RC and EP") Link: https://lore.kernel.org/linux-pci/aaffbe8d-7094-4083-8146-185f4a84e8a1@moroto.mountain Signed-off-by: Dan Carpenter <dan.carpenter@linaro.org> Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org> Reviewed-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
2024-07-04PCI: endpoint: Clean up error handling in vpci_scan_bus()Dan Carpenter
Smatch complains about inconsistent NULL checking in vpci_scan_bus(): drivers/pci/endpoint/functions/pci-epf-vntb.c:1024 vpci_scan_bus() error: we previously assumed 'vpci_bus' could be null (see line 1021) Instead of printing an error message and then crashing we should return an error code and clean up. Also the NULL check is reversed so it prints an error for success instead of failure. Fixes: e35f56bb0330 ("PCI: endpoint: Support NTB transfer between RC and EP") Link: https://lore.kernel.org/linux-pci/68e0f6a4-fd57-45d0-945b-0876f2c8cb86@moroto.mountain Signed-off-by: Dan Carpenter <dan.carpenter@linaro.org> Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org> Reviewed-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
2024-07-04PCI: endpoint: Make pci_epc_class struct constantGreg Kroah-Hartman
Now that the driver core allows for struct class to be in read-only memory, we should make all 'class' structures declared at build time placing them into read-only memory, instead of having to be dynamically allocated at runtime. Link: https://lore.kernel.org/linux-pci/2024061011-citable-herbicide-1095@gregkh Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
2024-07-04PCI: endpoint: Introduce 'epc_deinit' event and notify the EPF driversManivannan Sadhasivam
As like the 'epc_init' event, that is used to signal the EPF drivers about the EPC initialization, let's introduce 'epc_deinit' event that is used to signal EPC deinitialization. The EPC deinitialization applies only when any sort of fundamental reset is supported by the endpoint controller as per the PCIe spec. Reference: PCIe r6.0, sec 4.2.5.9.1 and 6.6.1. Currently, some EPC drivers like pcie-qcom-ep and pcie-tegra194 support PERST# as the fundamental reset. So the 'deinit' event will be notified to the EPF drivers when PERST# assert happens in the above mentioned EPC drivers. The EPF drivers, on receiving the event through the epc_deinit() callback should reset the EPF state machine and also cleanup any configuration that got affected by the fundamental reset like BAR, DMA etc... This change also warrants skipping the cleanups in unbind() if already done in epc_deinit(). Link: https://lore.kernel.org/r/20240606-pci-deinit-v1-2-4395534520dc@linaro.org Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org> Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org> Reviewed-by: Niklas Cassel <cassel@kernel.org> Reviewed-by: Siddharth Vadapalli <s-vadapalli@ti.com> Reviewed-by: Frank Li <Frank.Li@nxp.com>
2024-05-28PCI: endpoint: pci-epf-test: Handle Link Down eventManivannan Sadhasivam
Per PCIe r6.0, sec 5.2, a Link Down event can happen under any of the following circumstances: 1. Fundamental/Hot reset 2. Link disable transmission by upstream component 3. Moving from L2/L3 to L0 When the event happens, the EPC driver capable of detecting it may pass the notification to the EPF driver through link_down() callback in 'struct pci_epc_event_ops'. While the PCIe spec has not defined the actual behavior of the endpoint when the Link Down event happens, we may assume that at least the ongoing transactions need to be stopped as the link won't be active, so cancel the command handler work in the callback implementation pci_epf_test_link_down(). The work will be started again in pci_epf_test_link_up() once the link comes back again. Link: https://lore.kernel.org/linux-pci/20240430-pci-epf-rework-v4-10-22832d0d456f@linaro.org Tested-by: Niklas Cassel <cassel@kernel.org> Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org> Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org> [bhelgaas: update spec citation] Signed-off-by: Bjorn Helgaas <bhelgaas@google.com> Reviewed-by: Niklas Cassel <cassel@kernel.org>
2024-05-28PCI: endpoint: pci-epf-{mhi/test}: Move DMA initialization to EPC init callbackManivannan Sadhasivam
To maintain uniformity across EPF drivers, move DMA initialization to EPC init callback. This will also allow us to deinit DMA during PERST# assert in the further commits. For EPC drivers without PERST#, DMA deinit will only happen during driver unbind. Link: https://lore.kernel.org/linux-pci/20240430-pci-epf-rework-v4-6-22832d0d456f@linaro.org Tested-by: Niklas Cassel <cassel@kernel.org> Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org> Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org> Signed-off-by: Bjorn Helgaas <bhelgaas@google.com> Reviewed-by: Niklas Cassel <cassel@kernel.org>
2024-05-28PCI: endpoint: pci-epf-test: Refactor pci_epf_test_unbind() functionManivannan Sadhasivam
Move the pci_epc_clear_bar() and pci_epf_free_space() code to respective helper functions. This allows reusing the helpers in future commits. This also requires moving the pci_epf_test_unbind() definition below pci_epf_test_bind() to avoid forward declaration of the above helpers. No functional change. Link: https://lore.kernel.org/linux-pci/20240430-pci-epf-rework-v4-5-22832d0d456f@linaro.org Tested-by: Niklas Cassel <cassel@kernel.org> Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org> Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org> Signed-off-by: Bjorn Helgaas <bhelgaas@google.com> Reviewed-by: Niklas Cassel <cassel@kernel.org>
2024-05-28PCI: endpoint: Rename BME to Bus Master EnableManivannan Sadhasivam
BME which stands for 'Bus Master Enable' is not defined in the PCIe base spec even though it is commonly referred in many places (vendor docs). To align with the spec, rename it to its expansion 'Bus Master Enable'. Suggested-by: Damien Le Moal <dlemoal@kernel.org> Link: https://lore.kernel.org/linux-pci/20240430-pci-epf-rework-v4-3-22832d0d456f@linaro.org Link: https://lore.kernel.org/linux-pci/20240430-pci-epf-rework-v4-4-22832d0d456f@linaro.org Tested-by: Niklas Cassel <cassel@kernel.org> Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org> Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org> [bhelgaas: squash removal of irrelevant 'Link is enabled'] Signed-off-by: Bjorn Helgaas <bhelgaas@google.com> Reviewed-by: Niklas Cassel <cassel@kernel.org>
2024-05-28PCI: endpoint: Rename core_init() callback in 'struct pci_epc_event_ops' to ↵Manivannan Sadhasivam
epc_init() core_init() callback is used to notify the EPC initialization event to the EPF drivers. The 'core' prefix was used indicate that the controller IP core has completed initialization. But it serves no purpose as the EPF driver will only care about the EPC initialization as a whole and there is no real benefit to distinguish the IP core part. Rename the core_init() callback in 'struct pci_epc_event_ops' to epc_init() to make it more clear. Link: https://lore.kernel.org/linux-pci/20240430-pci-epf-rework-v4-2-22832d0d456f@linaro.org Tested-by: Niklas Cassel <cassel@kernel.org> Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org> Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org> Signed-off-by: Bjorn Helgaas <bhelgaas@google.com> Reviewed-by: Niklas Cassel <cassel@kernel.org>
2024-05-28PCI: endpoint: pci-epf-test: Use 'msix_capable' flag directly in ↵Manivannan Sadhasivam
pci_epf_test_alloc_space() Instead of using a local variable to cache the 'msix_capable' flag, use it directly to simplify the code. Suggested-by: Niklas Cassel <cassel@kernel.org> Link: https://lore.kernel.org/linux-pci/20240418-pci-epf-test-fix-v2-2-eacd54831444@linaro.org Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org> Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org> Signed-off-by: Bjorn Helgaas <bhelgaas@google.com> Reviewed-by: Frank Li <Frank.Li@nxp.com> Reviewed-by: Niklas Cassel <cassel@kernel.org>
2024-05-28PCI: endpoint: pci-epf-test: Make use of cached 'epc_features' in ↵Manivannan Sadhasivam
pci_epf_test_core_init() Instead of getting the epc_features from pci_epc_get_features() API, use the cached pci_epf_test::epc_features value to avoid the NULL check. Since the NULL check is already performed in pci_epf_test_bind(), having one more check in pci_epf_test_core_init() is redundant and it is not possible to hit the NULL pointer dereference. Also with commit a01e7214bef9 ("PCI: endpoint: Remove "core_init_notifier" flag"), 'epc_features' got dereferenced without the NULL check, leading to the following false positive Smatch warning: drivers/pci/endpoint/functions/pci-epf-test.c:784 pci_epf_test_core_init() error: we previously assumed 'epc_features' could be null (see line 747) Thus, remove the redundant NULL check and also use the epc_features:: {msix_capable/msi_capable} flags directly to avoid local variables. [kwilczynski: commit log] Fixes: 5e50ee27d4a5 ("PCI: pci-epf-test: Add support to defer core initialization") Closes: https://lore.kernel.org/linux-pci/024b5826-7180-4076-ae08-57d2584cca3f@moroto.mountain Link: https://lore.kernel.org/linux-pci/20240418-pci-epf-test-fix-v2-1-eacd54831444@linaro.org Reported-by: Dan Carpenter <dan.carpenter@linaro.org> Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org> Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org> Signed-off-by: Bjorn Helgaas <bhelgaas@google.com> Reviewed-by: Frank Li <Frank.Li@nxp.com> Reviewed-by: Niklas Cassel <cassel@kernel.org>
2024-05-28PCI: endpoint: Remove unused field in struct pci_epf_groupChristophe JAILLET
In "struct pci_epf_group", the 'type_group' field is unused. This was added, but already unused, by commit 70b3740f2c19 ("PCI: endpoint: Automatically create a function specific attributes group"). Thus, remove it. Found with cppcheck, unusedStructMember. [kwilczynski: commit log] Link: https://lore.kernel.org/linux-pci/6507d44b6c60a19af35a605e2d58050be8872ab6.1712341008.git.christophe.jaillet@wanadoo.fr Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr> Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org> Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
2024-05-21Merge tag 'pci-v6.10-changes' of ↵Linus Torvalds
git://git.kernel.org/pub/scm/linux/kernel/git/pci/pci Pull pci updates from Bjorn Helgaas: "Enumeration: - Skip E820 checks for MCFG ECAM regions for new (2016+) machines, since there's no requirement to describe them in E820 and some platforms require ECAM to work (Bjorn Helgaas) - Rename PCI_IRQ_LEGACY to PCI_IRQ_INTX to be more specific (Damien Le Moal) - Remove last user and pci_enable_device_io() (Heiner Kallweit) - Wait for Link Training==0 to avoid possible race (Ilpo Järvinen) - Skip waiting for devices that have been disconnected while suspended (Ilpo Järvinen) - Clear Secondary Status errors after enumeration since Master Aborts and Unsupported Request errors are an expected part of enumeration (Vidya Sagar) MSI: - Remove unused IMS (Interrupt Message Store) support (Bjorn Helgaas) Error handling: - Mask Genesys GL975x SD host controller Replay Timer Timeout correctable errors caused by a hardware defect; the errors cause interrupts that prevent system suspend (Kai-Heng Feng) - Fix EDR-related _DSM support, which previously evaluated revision 5 but assumed revision 6 behavior (Kuppuswamy Sathyanarayanan) ASPM: - Simplify link state definitions and mask calculation (Ilpo Järvinen) Power management: - Avoid D3cold for HP Pavilion 17 PC/1972 PCIe Ports, where BIOS apparently doesn't know how to put them back in D0 (Mario Limonciello) CXL: - Support resetting CXL devices; special handling required because CXL Ports mask Secondary Bus Reset by default (Dave Jiang) DOE: - Support DOE Discovery Version 2 (Alexey Kardashevskiy) Endpoint framework: - Set endpoint BAR to be 64-bit if the driver says that's all the device supports, in addition to doing so if the size is >2GB (Niklas Cassel) - Simplify endpoint BAR allocation and setting interfaces (Niklas Cassel) Cadence PCIe controller driver: - Drop DT binding redundant msi-parent and pci-bus.yaml (Krzysztof Kozlowski) Cadence PCIe endpoint driver: - Configure endpoint BARs to be 64-bit based on the BAR type, not the BAR value (Niklas Cassel) Freescale Layerscape PCIe controller driver: - Convert DT binding to YAML (Frank Li) MediaTek MT7621 PCIe controller driver: - Add DT binding missing 'reg' property for child Root Ports (Krzysztof Kozlowski) - Fix theoretical string truncation in PHY name (Sergio Paracuellos) NVIDIA Tegra194 PCIe controller driver: - Return success for endpoint probe instead of falling through to the failure path (Vidya Sagar) Renesas R-Car PCIe controller driver: - Add DT binding missing IOMMU properties (Geert Uytterhoeven) - Add DT binding R-Car V4H compatible for host and endpoint mode (Yoshihiro Shimoda) Rockchip PCIe controller driver: - Configure endpoint BARs to be 64-bit based on the BAR type, not the BAR value (Niklas Cassel) - Add DT binding missing maxItems to ep-gpios (Krzysztof Kozlowski) - Set the Subsystem Vendor ID, which was previously zero because it was masked incorrectly (Rick Wertenbroek) Synopsys DesignWare PCIe controller driver: - Restructure DBI register access to accommodate devices where this requires Refclk to be active (Manivannan Sadhasivam) - Remove the deinit() callback, which was only need by the pcie-rcar-gen4, and do it directly in that driver (Manivannan Sadhasivam) - Add dw_pcie_ep_cleanup() so drivers that support PERST# can clean up things like eDMA (Manivannan Sadhasivam) - Rename dw_pcie_ep_exit() to dw_pcie_ep_deinit() to make it parallel to dw_pcie_ep_init() (Manivannan Sadhasivam) - Rename dw_pcie_ep_init_complete() to dw_pcie_ep_init_registers() to reflect the actual functionality (Manivannan Sadhasivam) - Call dw_pcie_ep_init_registers() directly from all the glue drivers, not just those that require active Refclk from the host (Manivannan Sadhasivam) - Remove the "core_init_notifier" flag, which was an obscure way for glue drivers to indicate that they depend on Refclk from the host (Manivannan Sadhasivam) TI J721E PCIe driver: - Add DT binding J784S4 SoC Device ID (Siddharth Vadapalli) - Add DT binding J722S SoC support (Siddharth Vadapalli) TI Keystone PCIe controller driver: - Add DT binding missing num-viewport, phys and phy-name properties (Jan Kiszka) Miscellaneous: - Constify and annotate with __ro_after_init (Heiner Kallweit) - Convert DT bindings to YAML (Krzysztof Kozlowski) - Check for kcalloc() failure in of_pci_prop_intr_map() (Duoming Zhou)" * tag 'pci-v6.10-changes' of git://git.kernel.org/pub/scm/linux/kernel/git/pci/pci: (97 commits) PCI: Do not wait for disconnected devices when resuming x86/pci: Skip early E820 check for ECAM region PCI: Remove unused pci_enable_device_io() ata: pata_cs5520: Remove unnecessary call to pci_enable_device_io() PCI: Update pci_find_capability() stub return types PCI: Remove PCI_IRQ_LEGACY scsi: vmw_pvscsi: Do not use PCI_IRQ_LEGACY instead of PCI_IRQ_LEGACY scsi: pmcraid: Use PCI_IRQ_INTX instead of PCI_IRQ_LEGACY scsi: mpt3sas: Use PCI_IRQ_INTX instead of PCI_IRQ_LEGACY scsi: megaraid_sas: Use PCI_IRQ_INTX instead of PCI_IRQ_LEGACY scsi: ipr: Use PCI_IRQ_INTX instead of PCI_IRQ_LEGACY scsi: hpsa: Use PCI_IRQ_INTX instead of PCI_IRQ_LEGACY scsi: arcmsr: Use PCI_IRQ_INTX instead of PCI_IRQ_LEGACY wifi: rtw89: Use PCI_IRQ_INTX instead of PCI_IRQ_LEGACY dt-bindings: PCI: rockchip,rk3399-pcie: Add missing maxItems to ep-gpios Revert "genirq/msi: Provide constants for PCI/IMS support" Revert "x86/apic/msi: Enable PCI/IMS" Revert "iommu/vt-d: Enable PCI/IMS" Revert "iommu/amd: Enable PCI/IMS" Revert "PCI/MSI: Provide IMS (Interrupt Message Store) support" ...
2024-05-16Merge branch 'pci/misc'Bjorn Helgaas
- Constify pcibus_class (Heiner Kallweit) - Annotate pci_cache_line_size variables as __ro_after_init (Heiner Kallweit) - Clean up formatting of PCI accessor macros (Ilpo Järvinen) - Remove some OLPC dead code (Kunwu Chan) - Make pcie_bandwidth_capable() static (Ilpo Järvinen) * pci/misc: PCI: Make pcie_bandwidth_capable() static x86/pci: Remove OLPC dead code PCI: Clean up accessor macro formatting PCI/ERR: Cleanup misleading indentation inside if conditions PCI: Annotate pci_cache_line_size variables as __ro_after_init PCI: Constify pcibus_class
2024-05-16Merge branch 'pci/ims-removal'Bjorn Helgaas
- Remove unused Interrupt Message Store (IMS) support (Bjorn Helgaas) * pci/ims-removal: Revert "genirq/msi: Provide constants for PCI/IMS support" Revert "x86/apic/msi: Enable PCI/IMS" Revert "iommu/vt-d: Enable PCI/IMS" Revert "iommu/amd: Enable PCI/IMS" Revert "PCI/MSI: Provide IMS (Interrupt Message Store) support" Revert "PCI/MSI: Provide pci_ims_alloc/free_irq()" Revert "PCI/MSI: Provide stubs for IMS functions"
2024-05-16Merge branch 'pci/endpoint'Bjorn Helgaas
- Simplify pci_epf_test_alloc_space() by using pci_epc_get_next_free_bar() as other similar iterators do (Niklas Cassel) - Configure endpoint BARs as 64-bit if that's all the hardware supports, in addition to doing it if the BAR size is larger than 2GB (Niklas Cassel) - Remove superfluous pci_epf_configure_bar(), since pci_epf_alloc_space() now contains that functionality (Niklas Cassel) - Simplify pci_epf_test_set_bar() (Niklas Cassel) - Clean up pci_epf_test_unbind() to reduce indentation level (Niklas Cassel) * pci/endpoint: PCI: endpoint: pci-epf-test: Clean up pci_epf_test_unbind() PCI: endpoint: pci-epf-test: Simplify pci_epf_test_set_bar() loop PCI: endpoint: pci-epf-test: Remove superfluous code PCI: endpoint: Allocate a 64-bit BAR if that is the only option PCI: endpoint: pci-epf-test: Simplify pci_epf_test_alloc_space() loop
2024-05-16Merge branch 'pci/controller/tegra194'Bjorn Helgaas
- Return success from endpoint probe before incorrectly dropping the reference to the BPMP (Vidya Sagar) * pci/controller/tegra194: PCI: tegra194: Fix probe path for Endpoint mode
2024-05-16Merge branch 'pci/controller/rockchip'Bjorn Helgaas
- Configure endpoint BAR to be 64-bit if the PCI_BASE_ADDRESS_MEM_TYPE_64 flag is set instead of depending on the new BAR value itself (Niklas Cassel) - Set Subsystem Vendor ID correctly (Rick Wertenbroek) * pci/controller/rockchip: PCI: rockchip-ep: Remove wrong mask on subsys_vendor_id PCI: rockchip-ep: Set a 64-bit BAR if requested
2024-05-16Merge branch 'pci/controller/mt7621'Bjorn Helgaas
- Enlarge PHY name buffer to avoid snprintf() overflow (Sergio Paracuellos) * pci/controller/mt7621: PCI: mt7621: Fix string truncation in mt7621_pcie_parse_port()
2024-05-16Merge branch 'pci/controller/dwc'Bjorn Helgaas
- Move DBI accesses from dw_pcie_ep_init() to dw_pcie_ep_init_complete() so drivers for endpoints that require Refclk for DBI access, e.g., qcom and tegra194, can control when this happens (Manivannan Sadhasivam) - Add endpoint API kernel-doc (Manivannan Sadhasivam) - Remove .deinit() callback and instead call rcar_gen4_pcie_ep_deinit() explicitly from rcar-gen4, which was the only user (Manivannan Sadhasivam) - Rename dw_pcie_ep_exit() to dw_pcie_ep_deinit() to correspond with dw_pcie_ep_init() (Manivannan Sadhasivam) - Add dw_pcie_ep_cleanup() for drivers that need to clean up eDMA resources when PERST# is asserted, e.g., qcom, tegra194 (Manivannan Sadhasivam) - Rename dw_pcie_ep_init_complete() to dw_pcie_ep_init_registers() to better reflect the functionality (Manivannan Sadhasivam) - Call dw_pcie_ep_init_registers() directly from drivers instead of from dw_pcie_ep_init() so drivers, e.g., qcom and tegra194, can do it when Refclk is available (Manivannan Sadhasivam) - Remove the "core_init_notifier" flag, which previously identified drivers that required Refclk before DBI access, because it's now unnecessary (Manivannan Sadhasivam) * pci/controller/dwc: PCI: endpoint: Remove "core_init_notifier" flag PCI: dwc: ep: Call dw_pcie_ep_init_registers() API directly from all glue drivers PCI: dwc: ep: Rename dw_pcie_ep_init_complete() to dw_pcie_ep_init_registers() PCI: dwc: ep: Introduce dw_pcie_ep_cleanup() API for drivers supporting PERST# PCI: dwc: ep: Rename dw_pcie_ep_exit() to dw_pcie_ep_deinit() PCI: dwc: ep: Remove deinit() callback from struct dw_pcie_ep_ops PCI: dwc: ep: Add Kernel-doc comments for APIs PCI: dwc: ep: Fix DBI access failure for drivers requiring refclk from host
2024-05-16Merge branch 'pci/controller/cadence'Bjorn Helgaas
- Configure endpoint BAR to be 64-bit if the PCI_BASE_ADDRESS_MEM_TYPE_64 flag is set instead of depending on the new BAR value itself (Niklas Cassel) * pci/controller/cadence: PCI: cadence: Set a 64-bit BAR if requested
2024-05-16Merge branch 'pci/pm'Bjorn Helgaas
- Avoid D3cold for HP Pavilion 17 PC/1972 PCIe Ports because we can't get them back out of D3cold (Mario Limonciello) * pci/pm: PCI/PM: Avoid D3cold for HP Pavilion 17 PC/1972 PCIe Ports
2024-05-16Merge branch 'pci/of'Bjorn Helgaas
- Check for kcalloc() failure and handle it gracefully (Duoming Zhou) * pci/of: PCI: of_property: Return error for int_map allocation failure
2024-05-16Merge branch 'pci/msi'Bjorn Helgaas
- Update coding style to "mainline is normal path, errors are the exceptions" (Andy Shevchenko) * pci/msi: PCI/MSI: Make error path handling follow the standard pattern
2024-05-16Merge branch 'pci/hotplug'Bjorn Helgaas
- Update hotplug TODO notes (Nam Cao) * pci/hotplug: PCI: hotplug: Remove obsolete sgi_hotplug TODO notes PCI: hotplug: Document unchecked return value of pci_hp_add_bridge()
2024-05-16Merge branch 'pci/enumeration'Bjorn Helgaas
- Clear bridge Secondary Status errors after enumeration since enumeration causes many errors (Vidya Sagar) - Wait for Link Training==0 before starting Link retrain to avoid a race; this was done previously but broken by a faulty merge (Ilpo Järvinen) - Rename PCI_IRQ_LEGACY to PCI_IRQ_INTX to be more specific about what "LEGACY" means (Damien Le Moal) - Update return types of pci_find_capability() stubs to match the extern declarations for the actual implementations (Bjorn Helgaas) - Drop unnecessary pci_enable_device_io() from pata_cs5520 (Heiner Kallweit) - Drop unused pci_enable_device_io() (Heiner Kallweit) - On 2016 and newer BIOSes, skip early E820 check for ECAM regions described in ACPI MCFG; there's no spec requirement for E820 reservations, and some machines don't provide them (Bjorn Helgaas) - If devices were disconnected while suspended, don't wait for them when resuming (Ilpo Järvinen) * pci/enumeration: PCI: Do not wait for disconnected devices when resuming x86/pci: Skip early E820 check for ECAM region PCI: Remove unused pci_enable_device_io() ata: pata_cs5520: Remove unnecessary call to pci_enable_device_io() PCI: Update pci_find_capability() stub return types PCI: Remove PCI_IRQ_LEGACY scsi: vmw_pvscsi: Do not use PCI_IRQ_LEGACY instead of PCI_IRQ_LEGACY scsi: pmcraid: Use PCI_IRQ_INTX instead of PCI_IRQ_LEGACY scsi: mpt3sas: Use PCI_IRQ_INTX instead of PCI_IRQ_LEGACY scsi: megaraid_sas: Use PCI_IRQ_INTX instead of PCI_IRQ_LEGACY scsi: ipr: Use PCI_IRQ_INTX instead of PCI_IRQ_LEGACY scsi: hpsa: Use PCI_IRQ_INTX instead of PCI_IRQ_LEGACY scsi: arcmsr: Use PCI_IRQ_INTX instead of PCI_IRQ_LEGACY wifi: rtw89: Use PCI_IRQ_INTX instead of PCI_IRQ_LEGACY wifi: rtw88: Use PCI_IRQ_INTX instead of PCI_IRQ_LEGACY wifi: ath10k: Refer to INTX instead of LEGACY net: wangxun: Use PCI_IRQ_INTX instead of PCI_IRQ_LEGACY r8169: Use PCI_IRQ_INTX instead of PCI_IRQ_LEGACY net: alx: Use PCI_IRQ_INTX instead of PCI_IRQ_LEGACY net: atlantic: Use PCI_IRQ_INTX instead of PCI_IRQ_LEGACY net: amd-xgbe: Use PCI_IRQ_INTX instead of PCI_IRQ_LEGACY VMCI: Use PCI_IRQ_ALL_TYPES to remove PCI_IRQ_LEGACY use RDMA/vmw_pvrdma: Use PCI_IRQ_INTX instead of PCI_IRQ_LEGACY IB/qib: Use PCI_IRQ_INTX instead of PCI_IRQ_LEGACY drm/amdgpu: Use PCI_IRQ_INTX instead of PCI_IRQ_LEGACY mfd: intel-lpss: Use PCI_IRQ_INTX instead of PCI_IRQ_LEGACY ntb: idt: Use PCI_IRQ_INTX instead of PCI_IRQ_LEGACY platform/x86: intel_ips: Use PCI_IRQ_INTX instead of PCI_IRQ_LEGACY tty: 8250_pci: Use PCI_IRQ_INTX instead of PCI_IRQ_LEGACY usb: hcd-pci: Use PCI_IRQ_INTX instead of PCI_IRQ_LEGACY ASoC: Intel: avs: Use PCI_IRQ_INTX instead of PCI_IRQ_LEGACY Documentation: PCI: Use PCI_IRQ_INTX instead of PCI_IRQ_LEGACY PCI/portdrv: Use PCI_IRQ_INTX instead of PCI_IRQ_LEGACY PCI/MSI: Use PCI_IRQ_INTX instead of PCI_IRQ_LEGACY PCI: Clarify intent of LT wait PCI: Wait for Link Training==0 before starting Link retrain PCI: Clear Secondary Status errors after enumeration
2024-05-16Merge branch 'pci/edr'Bjorn Helgaas
- Specify Revision 6 of the "Enable DPC" _DSM function to match the implementation (Kuppuswamy Sathyanarayanan) - Check for failure of the "Locate Port" _DSM function (Kuppuswamy Sathyanarayanan) * pci/edr: PCI/EDR: Align EDR_PORT_LOCATE_DSM with PCI Firmware r3.3 PCI/EDR: Align EDR_PORT_DPC_ENABLE_DSM with PCI Firmware r3.3
2024-05-16Merge branch 'pci/doe'Bjorn Helgaas
- Add support for DOE Discovery version 2 (Alexey Kardashevskiy) * pci/doe: PCI/DOE: Support discovery version 2
2024-05-16Merge branch 'pci/cxl'Bjorn Helgaas
- Lock the upstream bridge while using it to perform a Secondary Bus Reset (Dave Jiang) - Return failure when attempting Secondary Bus Reset below a CXL Port that has SBR masked (Dave Jiang) - Add a "cxl_bus" reset method that temporarily unmasks SBR (Dave Jiang) - Add a warning if we reset a CXL type 3 memory device that was in use while being reset (Dave Jiang) * pci/cxl: cxl: Add post-reset warning if reset results in loss of previously committed HDM decoders PCI/CXL: Add 'cxl_bus' reset method for devices below CXL Ports PCI/CXL: Fail bus reset if upstream CXL Port has SBR masked PCI: Lock upstream bridge for pci_reset_function() PCI/CXL: Move CXL Vendor ID to pci_ids.h
2024-05-16Merge branch 'pci/aspm'Bjorn Helgaas
- Consolidate #defines for link states (L0s, L1, L1.1, etc) to simplify ASPM implementation (Ilpo Järvinen) - Simplify ASPM disable/enable mask calculation (Ilpo Järvinen) * pci/aspm: PCI/ASPM: Clean up ASPM disable/enable mask calculation PCI/ASPM: Consolidate link state defines
2024-05-16PCI: Do not wait for disconnected devices when resumingIlpo Järvinen
On runtime resume, pci_dev_wait() is called: pci_pm_runtime_resume() pci_pm_bridge_power_up_actions() pci_bridge_wait_for_secondary_bus() pci_dev_wait() While a device is runtime suspended along with its PCI hierarchy, the device could get disconnected. In such case, the link will not come up no matter how long pci_dev_wait() waits for it. Besides the above mentioned case, there could be other ways to get the device disconnected while pci_dev_wait() is waiting for the link to come up. Make pci_dev_wait() exit if the device is already disconnected to avoid unnecessary delay. The use cases of pci_dev_wait() boil down to two: 1. Waiting for the device after reset 2. pci_bridge_wait_for_secondary_bus() The callers in both cases seem to benefit from propagating the disconnection as error even if device disconnection would be more analoguous to the case where there is no device in the first place which return 0 from pci_dev_wait(). In the case 2, it results in unnecessary marking of the devices disconnected again but that is just harmless extra work. Also make sure compiler does not become too clever with dev->error_state and use READ_ONCE() to force a fetch for the up-to-date value. Link: https://lore.kernel.org/r/20240208132322.4811-1-ilpo.jarvinen@linux.intel.com Reported-by: Mika Westerberg <mika.westerberg@linux.intel.com> Tested-by: Mika Westerberg <mika.westerberg@linux.intel.com> Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com> Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
2024-05-16PCI: Remove unused pci_enable_device_io()Heiner Kallweit
After the last user was removed, remove this PCI core function. It's very unlikely that we'll see a new device requiring io space access, even though memory space access is supported. Link: https://lore.kernel.org/r/213ebf62-53a3-42b7-8518-ecd5cd6d6b08@gmail.com Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com> Signed-off-by: Bjorn Helgaas <bhelgaas@google.com> Reviewed-by: Damien Le Moal <dlemoal@kernel.org>
2024-05-15Revert "PCI/MSI: Provide IMS (Interrupt Message Store) support"Bjorn Helgaas
This reverts commit 0194425af0c87acaad457989a2c6d90dba58e776. IMS (Interrupt Message Store) support appeared in v6.2, but there are no users yet. Remove it for now. We can add it back when a user comes along. If this is re-added later, the relevant part of 41efa431244f ("PCI/MSI: Provide stubs for IMS functions") should be squashed into it. Link: https://lore.kernel.org/r/20240410221307.2162676-4-helgaas@kernel.org Signed-off-by: Bjorn Helgaas <bhelgaas@google.com> Reviewed-by: Kevin Tian <kevin.tian@intel.com> Reviewed-by: Thomas Gleixner <tglx@linutronix.de>
2024-05-15Revert "PCI/MSI: Provide pci_ims_alloc/free_irq()"Bjorn Helgaas
This reverts commit c9e5bea273834a63b5e9ba90ad94b305ba50704e. IMS (Interrupt Message Store) support appeared in v6.2, but there are no users yet. Remove it for now. We can add it back when a user comes along. If this is re-added later, the relevant part of 41efa431244f ("PCI/MSI: Provide stubs for IMS functions") should be squashed into it. Link: https://lore.kernel.org/r/20240410221307.2162676-3-helgaas@kernel.org Signed-off-by: Bjorn Helgaas <bhelgaas@google.com> Reviewed-by: Kevin Tian <kevin.tian@intel.com> Reviewed-by: Thomas Gleixner <tglx@linutronix.de>
2024-05-15PCI: rockchip-ep: Remove wrong mask on subsys_vendor_idRick Wertenbroek
Remove wrong mask on subsys_vendor_id. Both the Vendor ID and Subsystem Vendor ID are u16 variables and are written to a u32 register of the controller. The Subsystem Vendor ID was always 0 because the u16 value was masked incorrectly with GENMASK(31,16) resulting in all lower 16 bits being set to 0 prior to the shift. Remove both masks as they are unnecessary and set the register correctly i.e., the lower 16-bits are the Vendor ID and the upper 16-bits are the Subsystem Vendor ID. This is documented in the RK3399 TRM section 17.6.7.1.17 [kwilczynski: removed unnecesary newline] Fixes: cf590b078391 ("PCI: rockchip: Add EP driver for Rockchip PCIe controller") Link: https://lore.kernel.org/linux-pci/20240403144508.489835-1-rick.wertenbroek@gmail.com Signed-off-by: Rick Wertenbroek <rick.wertenbroek@gmail.com> Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org> Signed-off-by: Bjorn Helgaas <bhelgaas@google.com> Reviewed-by: Damien Le Moal <dlemoal@kernel.org> Cc: stable@vger.kernel.org
2024-05-08PCI: Make pcie_bandwidth_capable() staticIlpo Järvinen
pcie_bandwidth_capable() is only used within pci.c, make it static. Link: https://lore.kernel.org/r/20240507121758.13849-1-ilpo.jarvinen@linux.intel.com Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com> Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
2024-05-08PCI/EDR: Align EDR_PORT_LOCATE_DSM with PCI Firmware r3.3Kuppuswamy Sathyanarayanan
The "Downstream Port Containment related Enhancements" ECN of Jan 28, 2019 (document 12888 below), defined the EDR_PORT_LOCATE_DSM function with Revision ID 5 with a return value encoding (Bits 2:0 = Function, Bits 7:3 = Device, Bits 15:8 = Bus). When the ECN was integrated into PCI Firmware r3.3, sec 4.6.13, Bit 31 was added to indicate success or failure. Check Bit 31 for failure in acpi_dpc_port_get(). Link: https://lore.kernel.org/r/20240501022543.1626025-1-sathyanarayanan.kuppuswamy@linux.intel.com Link: https://members.pcisig.com/wg/PCI-SIG/document/12888 Fixes: ac1c8e35a326 ("PCI/DPC: Add Error Disconnect Recover (EDR) support") Signed-off-by: Kuppuswamy Sathyanarayanan <sathyanarayanan.kuppuswamy@linux.intel.com> [bhelgaas: split into two patches, update commit log] Signed-off-by: Bjorn Helgaas <bhelgaas@google.com> Tested-by: Satish Thatchanamurthy <Satish.Thatchanamurt@Dell.com> # one platform
2024-05-08PCI/EDR: Align EDR_PORT_DPC_ENABLE_DSM with PCI Firmware r3.3Kuppuswamy Sathyanarayanan
The "Downstream Port Containment related Enhancements" ECN of Jan 28, 2019 (document 12888 below), defined the EDR_PORT_DPC_ENABLE_DSM function with Revision ID 5 with Arg3 being an integer. But when the ECN was integrated into PCI Firmware r3.3, sec 4.6.12, it was defined as Revision ID 6 with Arg3 being a package containing an integer. The implementation in acpi_enable_dpc() supplies a package as Arg3 (arg4 in the code), but it previously specified Revision ID 5. Align this with PCI Firmware r3.3 by using Revision ID 6. If firmware implemented per the ECN, its Revision 5 function would receive a package as Arg3 when it expects an integer, so acpi_enable_dpc() would likely fail. If such firmware exists and lacks a Revision 6 function that expects a package, we may have to add support for Revision 5. Link: https://lore.kernel.org/r/20240501022543.1626025-1-sathyanarayanan.kuppuswamy@linux.intel.com Link: https://members.pcisig.com/wg/PCI-SIG/document/12888 Fixes: ac1c8e35a326 ("PCI/DPC: Add Error Disconnect Recover (EDR) support") Signed-off-by: Kuppuswamy Sathyanarayanan <sathyanarayanan.kuppuswamy@linux.intel.com> [bhelgaas: split into two patches, update commit log] Signed-off-by: Bjorn Helgaas <bhelgaas@google.com> Tested-by: Satish Thatchanamurthy <Satish.Thatchanamurt@Dell.com> # one platform
2024-05-08PCI/CXL: Add 'cxl_bus' reset method for devices below CXL PortsDave Jiang
By default Secondary Bus Reset (SBR) is masked for CXL Ports (see CXL r3.1, sec 8.1.5.2). Add cxl_reset_bus_function() (method "cxl_bus") to set the "Unmask SBR" bit in the upstream CXL Port before performing the bus reset and restore the original value afterwards. This method allows the user to perform a bus reset on a CXL device without needing to set the "Unmask SBR" bit via a user tool. Link: https://lore.kernel.org/r/20240502165851.1948523-5-dave.jiang@intel.com Signed-off-by: Dave Jiang <dave.jiang@intel.com> [bhelgaas: simplify commit log, invert condition to avoid negation] Signed-off-by: Bjorn Helgaas <bhelgaas@google.com> Reviewed-by: Jonathan Cameron <Jonathan.Cameron@huawei.com> Reviewed-by: Dan Williams <dan.j.williams@intel.com>
generated by cgit v1.2.3 (git 2.39.1) at 2025-07-30 21:15:46 +0000