| Age | Commit message (Collapse) | Author |
|---|
|
Hardware that supports only 32-bit config writes is not spec-compliant.
For example, if software performs a 16-bit write, we must do a 32-bit read,
merge in the 16 bits we intend to write, followed by a 32-bit write. If
the 16 bits we *don't* intend to write happen to have any RW1C (write-one-
to-clear) bits set, we just inadvertently cleared something we shouldn't
have.
Add a rate-limited warning when we do sub-32 bit config writes. Remove
similar probe-time warnings from some of the affected host bridge drivers.
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Enthusiastically-Acked-by: Russell King <rmk+kernel@armlinux.org.uk>
Acked-by: Shawn Lin <shawn.lin@rock-chips.com> # rockchip
Acked-by: Thierry Reding <treding@nvidia.com>
|
|
Currently the revision isn't available via sysfs/libudev thus if one wants
to know the value one needs to read through the config file, which can be
quite time-consuming because it wakes/powers up the device.
There are at least two userspace components which could make use the new
file: libpciaccess and libdrm. The former wakes up _every_ PCI device,
which can be observed via glxinfo when using Mesa 10.0+ drivers. The
latter, in association with Mesa 13.0, can lead to 2-3 second delays while
starting firefox, thunderbird or chromium.
Link: https://bugs.freedesktop.org/show_bug.cgi?id=98502
Tested-by: Mauro Santos <registo.mailling@gmail.com>
Signed-off-by: Emil Velikov <emil.velikov@collabora.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch
CC: Greg KH <gregkh@linuxfoundation.org>
|
|
Linux 4.8 added support for runtime suspending PCIe ports to D3hot with
commit 006d44e49a25 ("PCI: Add runtime PM support for PCIe ports"), but
excluded hotplug ports. Those are now afforded runtime PM by the present
commit.
Hotplug ports require a few extra considerations:
- The configuration space of the port remains accessible in D3hot, so all
the functions to read or modify the Slot Status and Slot Control
registers need not be modified. Even turning on slot power doesn't seem
to require the port to be in D0, at least the PCIe spec doesn't say so
and I confirmed that by testing with a Thunderbolt controller.
- However D0 is required to access devices on the secondary bus. This
happens in pciehp_check_link_status() and pciehp_configure_device() (both
called from board_added()) and in pciehp_unconfigure_device() (called
from remove_board()), so acquire a runtime PM ref for their invocation.
- The hotplug port stays active as long as it has active children. If all
hotplugged devices below the port runtime suspend, the port is allowed to
runtime suspend as well. Plug and unplug detection continues to work in
D3hot.
- Hotplug interrupts are delivered in-band, so while the hotplug port
itself is allowed to go to D3hot, its parent ports must stay in D0 for
interrupts to come through. Add a corresponding restriction to
pci_dev_check_d3cold().
- Runtime PM may only be allowed if the hotplug port is handled natively by
the OS. On ACPI systems, the port may alternatively be handled by the
firmware and things break if the OS puts the port into D3 behind the
firmware's back: E.g. Thunderbolt hotplug ports on non-Macs are handled
by Intel's firmware in System Management Mode and the firmware is known
to access devices on the port's secondary bus without checking first if
the port is in D0: https://bugzilla.kernel.org/show_bug.cgi?id=53811
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
CC: Mika Westerberg <mika.westerberg@linux.intel.com>
|
|
We're about to add runtime PM of hotplug ports, but we need to restrict it
to ports that are handled natively by the OS: If they're handled by the
firmware (which is the case for Thunderbolt on non-Macs), things would
break if the OS put the ports into D3hot behind the firmware's back.
To determine if a hotplug port is handled natively, one has to walk up from
the port to the root bridge and check the cached _OSC Control Field for the
value of the "PCI Express Native Hot Plug control" bit. There's already a
function to do that, device_is_managed_by_native_pciehp(), but it's private
to drivers/pci/hotplug/acpiphp_glue.c and only compiled in if
CONFIG_HOTPLUG_PCI_ACPI is enabled.
Make it public and move it to drivers/pci/pci-acpi.c, so that it is
available in the more general CONFIG_ACPI case.
The function contains a check if the device in question is a hotplug port
and returns false if it's not. The caller we're going to add doesn't need
this as it only calls the function if it actually *is* a hotplug port.
Move the check out of the function into the single existing caller.
Rename it to pciehp_is_native() and add some kerneldoc and polish.
No functional change intended.
Tested-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
We cache the PCI_EXP_SLTCAP_HPC bit in pci_dev->is_hotplug_bridge on device
probe, so there's no need to read it again when adding the ACPI hotplug
context.
Here's the call chain to prove that no ordering issue is introduced:
pci_scan_child_bus [drivers/pci/probe.c]
pci_scan_slot
pci_scan_single_device
pci_scan_device
pci_setup_device
set_pcie_hotplug_bridge
[is_hotplug_bridge bit is set here]
pci_scan_bridge
pci_add_new_bus
pci_alloc_child_bus
pcibios_add_bus [arch/(x86|arm64|ia64)/...]
acpi_pci_add_bus [drivers/pci/pci-acpi.c]
acpiphp_enumerate_slots [drivers/pci/hotplug/acpiphp_glue.c]
acpiphp_add_context
device_is_managed_by_native_pciehp
[is_hotplug_bridge bit is queried here]
No functional change intended.
Tested-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
The conditions to block D3 on parent ports are currently condensed into a
single expression in pci_dev_check_d3cold(). Upcoming commits will add
further conditions for hotplug ports, making this expression fairly large
and impenetrable. Unfold the conditions to maintain readability when they
are amended.
No functional change intended.
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
CC: Mika Westerberg <mika.westerberg@linux.intel.com>
CC: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
The conditions to allow runtime PM on PCIe ports are currently spread
across two different files: The condition relating to hotplug ports is
located in portdrv_pci.c whereas all other conditions are located in pci.c.
Consolidate all conditions in a single place in pci.c, thus making it
easier to follow the logic and amend conditions down the road.
Note that the condition relating to hotplug ports is inserted *before* the
condition relating to the "pcie_port_pm=force" command line option, so
runtime PM is not afforded to hotplug ports even if this option is given.
That's exactly how the code behaved up until now. If this is not desired,
the ordering of the conditions can simply be reversed.
No functional change intended.
Tested-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
Currently pcie_portdrv_probe() activates runtime PM on a PCIe port even
if it will never actually suspend because the BIOS is too old or the
"pcie_port_pm=off" option was specified on the kernel command line.
A few CPU cycles can be saved by not activating runtime PM at all in these
cases, because rpm_idle() and rpm_suspend() will bail out right at the
beginning when calling rpm_check_suspend_allowed(), instead of carrying out
various locking and assignments, invoking rpm_callback(), getting back
-EBUSY and rolling everything back.
The conditions checked in pci_bridge_d3_possible() are all static, they
never change during uptime of the system, hence it's safe to call this to
determine if runtime PM should be activated.
No functional change intended.
Tested-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
After a device has been added, removed or had its D3cold attributes
changed, we recheck whether its parent bridge may runtime suspend to D3hot
with pci_bridge_d3_update().
The most naive algorithm would be to iterate over the bridge's children and
check if any of them are blocking D3.
The function already tries to be a bit smarter than that by first checking
the device that was changed. If this device already blocks D3 on the
bridge, then walking over all the other children can be skipped. A
drawback of this approach is that if the device is *not* blocking D3, it
will be checked a second time by pci_walk_bus(). But that's cheap and is
outweighed by the performance gain of potentially skipping pci_walk_bus()
altogether.
The algorithm can be optimized further by taking into account if D3 is
currently allowed for the bridge, as shown in the following truth table:
(a) remove && bridge_d3: D3 is currently allowed for the bridge and
removing one of its children won't change
that. No action necessary.
(b) remove && !bridge_d3: D3 may now be allowed for the bridge if the
removed child was the only one blocking it.
Check all its siblings to verify that.
(c) !remove && bridge_d3: D3 may now be disallowed but this can only
be caused by the added/changed child, not
any of its siblings. Check only that single
device.
(d) !remove && !bridge_d3: D3 may now be allowed for the bridge if the
changed child was the only one blocking it.
Check all its siblings to verify that.
By checking beforehand if the changed child
is blocking D3, we may be able to skip
checking its siblings.
Currently we do not special-case option (a) and in case of option (c) we
gratuitously call pci_walk_bus(). Speed up the algorithm by adding these
optimizations. Reword the comments a bit in an attempt to improve clarity.
No functional change intended.
Tested-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
The algorithm to update the flag indicating whether a bridge may go to D3
makes a few optimizations based on whether the update was caused by the
removal of a device on the one hand, versus the addition of a device or the
change of its D3cold flags on the other hand.
The information whether the update pertains to a removal is currently
passed in by the caller, but the function may as well determine that itself
by examining the device in question, thereby allowing for a considerable
simplification and reduction of the code.
Out of several options to determine removal, I've chosen the function
device_is_registered() because it's cheap: It merely returns the
dev->kobj.state_in_sysfs flag. That flag is set through device_add() when
the root bus is scanned and cleared through device_remove(). The call to
pci_bridge_d3_update() happens after each of these calls, respectively, so
the ordering is correct.
No functional change intended.
Tested-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
This function is always called with an existing pci_dev struct, which
holds a reference on the pci_bus struct it resides on, which in turn
holds a reference on pci_bus->bridge, which is the pci_dev's parent.
Hence there's no need to acquire an additional ref on the parent.
More specifically, the pci_dev exists until pci_destroy_dev() drops the
final reference on it, so all calls to pci_bridge_d3_update() must be
finished before that. It is arguably the caller's responsibility to ensure
that it doesn't call pci_bridge_d3_update() with a pci_dev that might
suddenly disappear, but in any case the existing callers are all safe:
- The call in pci_destroy_dev() happens before the call to put_device().
- The call in pci_bus_add_device() is synchronized with pci_destroy_dev()
using pci_lock_rescan_remove().
- The calls to pci_d3cold_disable() from the xhci and nouveau drivers
are safe because a ref on the pci_dev is held as long as it's bound to
a driver.
- The calls to pci_d3cold_enable() / pci_d3cold_disable() when modifying
the sysfs "d3cold_allowed" entry are also safe because kernfs_drain()
waits for existing sysfs users to finish before removing the entry,
and pci_destroy_dev() is called way after that.
No functional change intended.
Tested-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
Add support for inbound DMA mapping. The range of the inbound mapping is
configured by the optional device tree property 'dma-ranges'.
While inbound mapping is done automatically in the ASIC on most iProc-based
SoCs, newer ASICs (e.g., Stingray) require inbound mapping to be configured
explicitly in software.
[bhelgaas: fold in fixes to avoid 32-bit division in iproc_pcie_ib_write()
and uninitialized return value in iproc_pcie_setup_ib() from Arnd Bergmann
<arnd@arndb.de>]
Signed-off-by: Oza Oza <oza.oza@broadcom.com>
Signed-off-by: Ray Jui <ray.jui@broadcom.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Scott Branden <scott.branden@broadcom.com>
|
|
Improve the iProc PCIe outbound mapping code by making it more generic and
removing redundant device tree properties 'brcm,pcie-ob-window-size' and
'brcm,pcie-ob-oarr-size'. The driver is still backward compatible to
device tree binaries with the two properties specified.
The driver now automatically configures the correct mapping window size and
number of mapping windows based on the value of device tree property
'ranges' and the capability of of the iProc PCIe controller.
Signed-off-by: Oza Oza <oza.oza@broadcom.com>
Signed-off-by: Ray Jui <ray.jui@broadcom.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Scott Branden <scott.branden@broadcom.com>
|
|
Add support for the second generation of the iProc PCIe PAXC host
controller.
Signed-off-by: Ray Jui <ray.jui@broadcom.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Anup Patel <anup.patel@broadcom.com>
Reviewed-by: Scott Branden <scott.branden@broadcom.com>
|
|
After we send a PCI_EJECTION_COMPLETE message to the host, the host will
immediately send us a PCI_BUS_RELATIONS message with
relations->device_count == 0, so pci_devices_present_work(), running on
another thread, can find the being-ejected device, mark the
hpdev->reported_missing to true, and run list_move_tail()/list_del() for
the device -- this races hv_eject_device_work() -> list_del().
Move the list_del() in hv_eject_device_work() to an earlier place, i.e.,
before we send PCI_EJECTION_COMPLETE, so later the
pci_devices_present_work() can't see the device.
Signed-off-by: Dexuan Cui <decui@microsoft.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Jake Oshins <jakeo@microsoft.com>
Acked-by: K. Y. Srinivasan <kys@microsoft.com>
CC: Haiyang Zhang <haiyangz@microsoft.com>
CC: Vitaly Kuznetsov <vkuznets@redhat.com>
|
|
1. We don't really need such a big on-stack buffer when sending the
teardown_packet: vmbus_sendpacket() here only uses sizeof(struct
pci_message).
2. In the hot-remove case (PCI_EJECT), after we send PCI_EJECTION_COMPLETE
to the host, the host will send a RESCIND_CHANNEL message to us and the
host won't access the per-channel ringbuffer any longer, so we needn't send
PCI_RESOURCES_RELEASED/PCI_BUS_D0EXIT to the host, and we shouldn't expect
the host's completion message of PCI_BUS_D0EXIT, which will never come.
3. We should send PCI_BUS_D0EXIT after hv_send_resources_released().
Signed-off-by: Dexuan Cui <decui@microsoft.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Jake Oshins <jakeo@microsoft.com>
Acked-by: K. Y. Srinivasan <kys@microsoft.com>
CC: Haiyang Zhang <haiyangz@microsoft.com>
CC: Vitaly Kuznetsov <vkuznets@redhat.com>
|
|
We don't really need such a big on-stack buffer. vmbus_sendpacket() here
only uses sizeof(struct pci_child_message).
Signed-off-by: Dexuan Cui <decui@microsoft.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Jake Oshins <jakeo@microsoft.com>
|
|
I returned to Synopsys and so I am sending this patch to update the email
address of the pcie-designware-plat author.
Signed-off-by: Joao Pinto <jpinto@synopsys.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
|
|
During enumeration with multi-function EP devices, access to the
configuration space of a non-existent function results in an unsupported
request being returned as expected. By default the PAXB-based iProc PCIe
controller forwards this as an APB error to the host system and that causes
an exception, which is undesired.
Disable this undesired behaviour and let the kernel PCI stack deal with an
access to the non-existent function, in which case a vendor ID of 0xffff is
returned and handled gracefully.
Reported-by: JD Zheng <jiandong.zheng@broadcom.com>
Signed-off-by: Ray Jui <ray.jui@broadcom.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: JD Zheng <jiandong.zheng@broadcom.com>
Reviewed-by: Oza Oza <oza.oza@broadcom.com>
Reviewed-by: Scott Branden <scott.branden@broadcom.com>
|
|
The iProc PCIe driver is currently using type IPROC_PCIE_PAXB for the
following SoCs: NS, NSP, Cygnus, NS2, and Pegasus. In fact, the BCMA-based
NS uses a legacy PAXB controller that is slightly different from the PAXB
controller used in the rest of SoCs, e.g., some registers are missing and
it does not require software configuration of outbound/inbound address
mapping.
Add a new type, IPROC_PCIE_PAXB_BCMA, to allow us to properly support the
BCMA-based NS along with other iProc-based SoCs going forward.
Signed-off-by: Ray Jui <ray.jui@broadcom.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Scott Branden <scott.branden@broadcom.com>
|
|
During initialization, the current iProc PCIe host driver resets PAXC and
the downstream internal endpoint device that PAXC connects to. If the
endpoint device is already loaded with firmware and has started running
from the bootloader stage, this downstream reset causes the endpoint device
to stop working.
Signed-off-by: Ray Jui <raj.jui@broadcom.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Scott Branden <scott.branden@broadcom.com>
|
|
As the number of iProc PCIe core registers starts to grow and differ
between different revisions of the iProc PCIe controllers, the
current way of populating each individual unsupported register with
value 'IPROC_PCIE_REG_INVALID' with a table entry has become a bit
messy and is difficult to scale up in the future.
Improve the current driver by populating the invalid entries with code
instead of through individual table entries. This helps to avoid a
significant number of invalid table entries when support for the next
revision of the iProc controller is added.
Signed-off-by: Ray Jui <ray.jui@broadcom.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Scott Branden <scott.branden@broadcom.com>
|
|
Use DEVICE_ATTR_RW for read-write attributes. This simplifies the source
code, improves readability, and reduces the chance of inconsistencies.
The semantic patch that makes this change is as follows:
(http://coccinelle.lip6.fr/)
// <smpl>
@rw@
declarer name DEVICE_ATTR;
identifier x,x_show,x_store;
@@
DEVICE_ATTR(x, \(0644\|S_IRUGO|S_IWUSR\), x_show, x_store);
@script:ocaml@
x << rw.x;
x_show << rw.x_show;
x_store << rw.x_store;
@@
if not (x^"_show" = x_show && x^"_store" = x_store)
then Coccilib.include_match false
@@
declarer name DEVICE_ATTR_RW;
identifier rw.x,rw.x_show,rw.x_store;
@@
- DEVICE_ATTR(x, \(0644\|S_IRUGO|S_IWUSR\), x_show, x_store);
+ DEVICE_ATTR_RW(x);
// </smpl>
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull x86 fixes from Ingo Molnar:
"Misc fixes:
- fix an Intel/MID boot crash/hang bug
- fix a cache topology mis-parsing bug on certain AMD CPUs
- fix a virtualization firmware bug by adding a check+quirk
workaround on the kernel side"
* 'x86-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86/cpu: Deal with broken firmware (VMWare/XEN)
x86/cpu/AMD: Fix cpu_llc_id for AMD Fam17h systems
x86/platform/intel-mid: Retrofit pci_platform_pm_ops ->get_state hook
|
|
Make sure to drop any device reference taken by vio_find_node() when
adding and removing virtual I/O slots.
Fixes: 5eeb8c63a38f ("[PATCH] PCI Hotplug: rpaphp: Move VIO registration")
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci
Pull PCI fixes from Bjorn Helgaas:
- Update MAINTAINERS for Intel VMD driver filename
- Update Rockchip rk3399 host bridge driver DTS and resets
- Fix ROM shadow problem that made some video device initialization
fail
* tag 'pci-v4.9-fixes-3' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci:
PCI: VMD: Update filename to reflect move
arm64: dts: rockchip: add three new resets for rk3399 PCIe controller
PCI: rockchip: Add three new resets as required properties
PCI: Don't attempt to claim shadow copies of ROM
|
|
Add support for the LS1046a PCIe controller. This device has a different
LUT_DBG offset, so add "lut_dbg" to ls_pcie_drvdata to
describe this difference.
[bhelgaas: changelog, remove now-unused PCIE_LUT_DBG]
Signed-off-by: Mingkai Hu <mingkai.hu@nxp.com>
Signed-off-by: Minghuan Lian <Minghuan.Lian@nxp.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
|
|
One some systems, the firmware does not allow certain PCI devices to be put
in deep D-states. This can cause problems for wakeup signalling, if the
device does not support PME# in the deepest allowed suspend state. For
example, Pierre reports that on his system, ACPI does not permit his xHCI
host controller to go into D3 during runtime suspend -- but D3 is the only
state in which the controller can generate PME# signals. As a result, the
controller goes into runtime suspend but never wakes up, so it doesn't work
properly. USB devices plugged into the controller are never detected.
If the device relies on PME# for wakeup signals but is not capable of
generating PME# in the target state, the PCI core should accurately report
that it cannot do wakeup from runtime suspend. This patch modifies the
pci_dev_run_wake() routine to add this check.
Reported-by: Pierre de Villemereuil <flyos@mailoo.org>
Tested-by: Pierre de Villemereuil <flyos@mailoo.org>
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
CC: stable@vger.kernel.org
CC: Lukas Wunner <lukas@wunner.de>
|
|
The driver core clears the driver data to NULL after device_release or on
probe failure. Thus, it is not needed to manually clear the device driver
data to NULL.
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Keith Busch <keith.busch@intel.com>
|
|
There is an error message from devm_ioremap_resource() already, so remove
the dev_err() call to avoid redundant error messages.
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
|
|
There is an error message from devm_ioremap_resource() already, so remove
the dev_err() call to avoid redundant error messages.
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
|
|
There is an error message from devm_ioremap_resource() already, so remove
the dev_err() call to avoid redundant error messages.
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Ley Foon Tan <lftan@altera.com>
|
|
Use the builtin_platform_driver() macro to make the code simpler.
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
|
|
pm_rst, aclk_rst, pclk_rst was controlled by ROM code so the software
wasn't needed to control it again in theory. But it didn't work properly,
so we do need to do it again and add enough delay between the assert of
pm_rst and the deassert of pm_rst. The Soc intergrated with this
controller, rk3399, is still under MP test internally, so the backward
compatibility won't be a big deal.
Signed-off-by: Shawn Lin <shawn.lin@rock-chips.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Heiko Stuebner <heiko@sntech.de>
Acked-by: Rob Herring <robh@kernel.org>
|
|
This is a variant of pci_alloc_irq_vectors() that allows passing a struct
irq_affinity to provide fine-grained IRQ affinity control.
For now this means being able to exclude vectors at the beginning or end of
the MSI vector space, but it could also be used for any other quirks needed
in the future (e.g. more vectors than CPUs, or excluding CPUs from the
spreading).
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Acked-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Jens Axboe <axboe@kernel.dk>
Cc: linux-block@vger.kernel.org
Cc: linux-pci@vger.kernel.org
Link: http://lkml.kernel.org/r/1478654107-7384-6-git-send-email-hch@lst.de
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
|
|
No API change yet, just pass it down all the way from
pci_alloc_irq_vectors() to the core MSI code.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Acked-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Jens Axboe <axboe@kernel.dk>
Cc: linux-block@vger.kernel.org
Cc: linux-pci@vger.kernel.org
Link: http://lkml.kernel.org/r/1478654107-7384-5-git-send-email-hch@lst.de
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
|
|
Only calculate the affinity for the main I/O vectors, and skip the
pre or post vectors specified by struct irq_affinity.
Also remove the irq_affinity cpumask argument that has never been used.
If we ever need it in the future we can pass it through struct
irq_affinity.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Acked-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Jens Axboe <axboe@kernel.dk>
Cc: linux-block@vger.kernel.org
Cc: linux-pci@vger.kernel.org
Link: http://lkml.kernel.org/r/1478654107-7384-4-git-send-email-hch@lst.de
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
|
|
Only calculate the affinity for the main I/O vectors, and skip the pre or
post vectors specified by struct irq_affinity.
Also remove the irq_affinity cpumask argument that has never been used. If
we ever need it in the future we can pass it through struct irq_affinity.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Acked-by: Jens Axboe <axboe@kernel.dk>
Cc: linux-block@vger.kernel.org
Cc: linux-pci@vger.kernel.org
Link: http://lkml.kernel.org/r/1478654107-7384-3-git-send-email-hch@lst.de
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
|
|
If msi_setup_entry() fails to allocate an affinity mask, it logs a message
but continues on and allocates an MSI entry with entry->affinity == NULL.
Check for this case in pci_irq_get_affinity() so we don't try to
dereference a NULL pointer.
[bhelgaas: changelog]
Fixes: ee8d41e53efe "pci/msi: Retrieve affinity for a vector"
Signed-off-by: Jan Beulich <jbeulich@suse.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
CC: Thomas Gleixner <tglx@linutronix.de>
|
|
If we're using a shadow copy of a PCI device ROM, the shadow copy is in RAM
and the device never sees accesses to it and doesn't respond to it. We
don't have to route the shadow range to the PCI device, and the device
doesn't have to claim the range.
Previously we treated the shadow copy as though it were the ROM BAR, and we
failed to claim it because the region wasn't routed to the device:
pci 0000:01:00.0: Video device with shadowed ROM at [mem 0x000c0000-0x000dffff]
pci_bus 0000:01: Allocating resources
pci 0000:01:00.0: can't claim BAR 6 [mem 0x000c0000-0x000dffff]: no compatible bridge window
The failure path of pcibios_allocate_dev_rom_resource() cleared out the
resource start address, which also caused the following ioremap() warning:
WARNING: CPU: 0 PID: 116 at /build/linux-akdJXO/linux-4.8.0/arch/x86/mm/ioremap.c:121 __ioremap_caller+0x1ec/0x370
ioremap on RAM at 0x0000000000000000 - 0x000000000001ffff
Handle an option ROM shadow copy as RAM, without trying to insert it into
the iomem resource tree.
This fixes a regression caused by 0c0e0736acad ("PCI: Set ROM shadow
location in arch code, not in PCI core"), which appeared in v4.6. The
regression causes video device initialization to fail. This was reported
on AMD Turks, but it likely affects others as well.
Fixes: 0c0e0736acad ("PCI: Set ROM shadow location in arch code, not in PCI core")
Reported-and-tested-by: Vecu Bosseur <vecu.bosseur@gmail.com>
Link: https://bugs.launchpad.net/ubuntu/+source/linux/+bug/1627496
Link: https://bugzilla.kernel.org/show_bug.cgi?id=175391
Link: https://bugzilla.redhat.com/show_bug.cgi?id=1352272
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
CC: stable@vger.kernel.org # v4.6+
|
|
Use xenbus_read_unsigned() instead of xenbus_scanf() when possible.
This requires to change the type of the read from int to unsigned,
but this case has been wrong before: negative values are not allowed
for the modified case.
Cc: bhelgaas@google.com
Cc: linux-pci@vger.kernel.org
Signed-off-by: Juergen Gross <jgross@suse.com>
Acked-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: David Vrabel <david.vrabel@citrix.com>
|
|
Commit cc7cc02bada8 ("PCI: Query platform firmware for device power
state") augmented struct pci_platform_pm_ops with a ->get_state hook and
implemented it for acpi_pci_platform_pm, the only pci_platform_pm_ops
existing till v4.7.
However v4.8 introduced another pci_platform_pm_ops for Intel Mobile
Internet Devices with commit 5823d0893ec2 ("x86/platform/intel-mid: Add
Power Management Unit driver"). It is missing the ->get_state hook,
which is fatal since pci_set_platform_pm() enforces its presence. Andy
Shevchenko reports that without the present commit, such a device
"crashes without even a character printed out on serial console and
reboots (since watchdog)".
Retrofit mid_pci_platform_pm with the missing callback to fix the
breakage.
Acked-and-tested-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Fixes: cc7cc02bada8 ("PCI: Query platform firmware for device power state")
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Acked-by: Bjorn Helgaas <bhelgaas@google.com>
Cc: linux-pci@vger.kernel.org
Cc: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: http://lkml.kernel.org/r/7c1567d4c49303a4aada94ba16275cbf56b8976b.1477221514.git.lukas@wunner.de
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci
Pull PCI fixes from Bjorn Helgaas:
- fix for a Qualcomm driver issue that causes a use-before-set crash
- fix for DesignWare iATU unroll support that causes external aborts
when enabling the host bridge
* tag 'pci-v4.9-fixes-2' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci:
PCI: designware: Check for iATU unroll support after initializing host
PCI: qcom: Fix pp->dev usage before assignment
|
|
dw_pcie_iatu_unroll_enabled() reads a dbi_base register. Reading any
dbi_base register before pp->ops->host_init has been called causes
"imprecise external abort" on platforms like ARTPEC-6, where the PCIe
module is disabled at boot and first enabled in pp->ops->host_init. Move
dw_pcie_iatu_unroll_enabled() to dw_pcie_setup_rc(), since it is after
pp->ops->host_init, but before pp->iatu_unroll_enabled is actually used.
Fixes: a0601a470537 ("PCI: designware: Add iATU Unroll feature")
Tested-by: James Le Cuirot <chewi@gentoo.org>
Signed-off-by: Niklas Cassel <niklas.cassel@axis.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Joao Pinto <jpinto@synopsys.com>
Acked-by: Olof Johansson <olof@lixom.net>
|
|
Make hv_irq_mask() and hv_irq_unmask() static as they are only used in
pci-hyperv.c
This fixes a sparse warning.
Signed-off-by: Tobias Klauser <tklauser@distanz.ch>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: K. Y. Srinivasan <kys@microsoft.com>
|
|
The Kconfig currently controlling compilation of this code is:
drivers/pci/hotplug/Kconfig:config HOTPLUG_PCI_S390
drivers/pci/hotplug/Kconfig: bool "System z PCI Hotplug Support"
...meaning that it currently is not being built as a module by anyone.
Lets remove the couple traces of modular infrastructure use, so that
when reading the driver there is no doubt it is builtin-only.
We also delete the MODULE_LICENSE tag etc. since all that information
was (or is now) contained at the top of the file in the comments.
We don't exchange module.h for init.h or export.h since the file
does not contain any initcalls or EXPORT of symbols.
Cc: Sebastian Ott <sebott@linux.vnet.ibm.com>
Cc: Gerald Schaefer <gerald.schaefer@de.ibm.com>
Cc: Bjorn Helgaas <bhelgaas@google.com>
Cc: linux-s390@vger.kernel.org
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
|
|
Initialize pp->dev in qcom_pcie_probe() before calling get_resources(),
which uses it.
[bhelgaas: changelog]
Fixes: e6a087eeaf91 ("PCI: qcom: Remove redundant struct qcom_pcie.dev")
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
|
|
commit 92ca8d20dee2 ("genirq/msi: Switch to new irq spreading")
introduced new parameter to msi_init_setup and but did not update
docbook comments. Fixes 'make htmldocs' warning.
Signed-off-by: Stephen Hemminger <sthemmin@microsoft.com>
Cc: bhelgaas@google.com
Cc: linux-pci@vger.kernel.org
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
|
|
Although I am leaving Synopsys, I would like to keep working with the linux
kernel community and help in what you might find useful. For that I am
sending this patch to change my contact e-mail.
Signed-off-by: Joao Pinto <jpinto@synopsys.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
|
|
Commit fefe6733e516 ("PCI: layerscape: Move struct pcie_port setup
to probe function") changed the init ordering of the pcie structure,
but started to use the pcie->drvdata field before initializing it.
Mayhem follows.
Fix this by moving the drvdata assignment right before the first use.
Tested on LS2085a.
Fixes: efe6733e516 ("PCI: layerscape: Move struct pcie_port setup to probe function")
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
|
