| Age | Commit message (Collapse) | Author |
|---|
|
Sporadic reset issues have been observed with an Intel 750 NVMe drive while
assigning the physical function to the guest machine. The sequence of
events observed is as follows:
- perform a Function Level Reset (FLR)
- sleep up to 1000ms total
- read ~0 from PCI_COMMAND (CRS completion for config read)
- warn that the device didn't return from FLR
- touch the device before it's ready
- device drops config writes when we restore register settings (there's
no mechanism for software to learn about CRS completions for writes)
- incomplete register restore leaves device in inconsistent state
- device probe fails because device is in inconsistent state
After reset, an endpoint may respond to config requests with Configuration
Request Retry Status (CRS) to indicate that it is not ready to accept new
requests. See PCIe r3.1, sec 2.3.1 and 6.6.2.
Increase the timeout value from 1 second to 60 seconds to cover the period
where device responds with CRS and also report polling progress.
Signed-off-by: Sinan Kaya <okaya@codeaurora.org>
[bhelgaas: include the mandatory 100ms in the delays we print]
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
|
|
Configuration Request Retry Status (CRS) was previously hidden inside
pci_bus_read_dev_vendor_id(). We want to add support for CRS in other
situations, such as waiting for a device to become ready after a Function
Level Reset.
Move CRS handling into pci_bus_wait_crs() so it can be called from other
places.
Signed-off-by: Sinan Kaya <okaya@codeaurora.org>
[bhelgaas: pass pointer, not value, to pci_bus_wait_crs() so caller gets
correct Vendor ID]
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
|
|
Add pci_bus_crs_vendor_id() to determine whether data returned for a config
read of the Vendor ID indicates a Configuration Request Retry Status (CRS)
response.
Per PCIe r3.1, sec 2.3.2, this data is only returned if:
- CRS Software Visibility is enabled,
- a config read includes both bytes of the Vendor ID, and
- the read receives a CRS completion
Signed-off-by: Sinan Kaya <okaya@codeaurora.org>
[bhelgaas: changelog, change name to pci_bus_crs_vendor_id(), make static
in probe.c, use it in pci_bus_read_dev_vendor_id()]
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
|
|
While waiting for a device to become ready (i.e., to return a non-CRS
completion to a read of its Vendor ID), if we got a valid response to the
very last read before timing out, we printed a warning and gave up on the
device even though it was actually ready.
For a typical 60s timeout, we wait about 65s (it's not exact because of the
exponential backoff), but we treated devices that became ready between 33s
and 65s as though they failed.
Move the Device ID read later so we check whether the device is ready
before checking for a timeout.
Thanks to Sinan Kaya <okaya@codeaurora.org>, reorder reads so we always
check device presence after sleep, since it's pointless to sleep unless we
recheck afterwards.
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
|
|
Call pci_unmap_iospace() to clean up if probe fails.
Signed-off-by: Jeffy Chen <jeffy.chen@rock-chips.com>
Signed-off-by: Shawn Lin <shawn.lin@rock-chips.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
|
|
Call irq_domain_remove() to clean up if probe fails.
Signed-off-by: Jeffy Chen <jeffy.chen@rock-chips.com>
Signed-off-by: Shawn Lin <shawn.lin@rock-chips.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
|
|
Disable vpcie0v9 regulator if resume_noirq fails.
Signed-off-by: Jeffy Chen <jeffy.chen@rock-chips.com>
Signed-off-by: Shawn Lin <shawn.lin@rock-chips.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
|
|
We observed that the clk_pciephy_ref is still enabled when we fail to probe
the driver.
root@linaro-alip:~# grep pcie /sys/kernel/debug/clk/clk_summary
clk_pciephy_ref 1 1 24000000 0 0
clk_pcie_pm 0 0 24000000 0 0
clk_pcie_core_cru 0 0 125000000 0 0
clk_pciephy_ref100m 0 0 100000000 0 0
aclk_pcie 0 0 148500000 0 0
aclk_perf_pcie 0 0 148500000 0 0
pclk_pcie 0 0 37125000 0 0
clk_pcie_core 0 0 0 0 0
clk_pciephy_ref is used by the PHY driver and we need to properly disable
it for this case. Add error handling in rockchip_pcie_init_port() and
rockchip_pcie_resume_noirq() to fix this issue.
Signed-off-by: Shawn Lin <shawn.lin@rock-chips.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
|
|
Factor out rockchip_pcie_deinit_phys() so it can be reused by
rockchip_pcie_suspend_noirq() and rockchip_pcie_remove(). No functional
change intended.
Signed-off-by: Shawn Lin <shawn.lin@rock-chips.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
|
|
Factor out rockchip_pcie_disable_clocks() so it can be reused by other
functions.
No functional change intended, but it does change the order of unpreparing
clocks in the rockchip_pcie_resume_noirq() error path so it matches the
other paths.
Signed-off-by: Shawn Lin <shawn.lin@rock-chips.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
|
|
Factor out rockchip_pcie_enable_clocks() so it can be reused by
rockchip_pcie_resume_noirq() and rockchip_pcie_probe().
No functional change intended, but it does change the order of unpreparing
clocks in the rockchip_pcie_resume_noirq() error path.
Signed-off-by: Shawn Lin <shawn.lin@rock-chips.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
|
|
Factor out rockchip_pcie_setup_irq() to prepare for future bug fixes. No
functional change intended.
Signed-off-by: Shawn Lin <shawn.lin@rock-chips.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
|
|
The reset GPIO can be connected to a I2C or SPI IO expander, which may
sleep, so it is safer to use the gpiod_set_value_cansleep() variant
instead.
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Shawn Lin <shawn.lin@rock-chips.com>
|
|
Use the PCI_NUM_INTX macro to indicate the number of PCI INTx interrupts
rather than the magic number 4. This makes it clearer where the number
comes from & what it relates to.
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Cc: Heiko Stuebner <heiko@sntech.de>
Cc: Shawn Lin <shawn.lin@rock-chips.com>
|
|
Commit a53e35db70d1 ("reset: Ensure drivers are explicit when requesting
reset lines") started to transition the reset control request API calls to
explicitly state whether the driver needs exclusive or shared reset control
behavior. Convert all drivers requesting exclusive resets to the explicit
API call so the temporary transition helpers can be removed.
No functional changes.
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Shawn Lin <shawn.lin@rock-chips.com>
|
|
Configuration Request Retry Status ("CRS") completions are a required part
of PCIe. A PCIe device may respond to config a request with a CRS
completion to indicate that it needs more time to initialize. A Root Port
that receives a CRS completion may automatically retry the request, or it
may treat the request as a failed transaction. For a failed read, it will
likely synthesize all 1's data, i.e., 0xffffffff, to complete the read to
the CPU.
CRS Software Visibility ("CRS SV") is an optional feature. Per PCIe r3.1,
sec 2.3.2, if supported and enabled, a Root Port that receives a CRS
completion for a config read of the Vendor ID will synthesize 0x0001 data
(an invalid Vendor ID) instead of retrying or failing the transaction. The
0x0001 data makes the CRS completion visible to software, so it can perform
other tasks while waiting for the device.
The iProc "Stingray" PCIe controller does not support CRS completions
correctly. From the Stingray PCIe Controller spec:
4.7.3.3. Retry Status On Configuration Cycle
Endpoints are allowed to generate retry status on configuration cycles.
In this case, the RC needs to re-issue the request. The IP does not
handle this because the number of configuration cycles needed will
probably be less than the total number of non-posted operations needed.
When a retry status is received on the User RX interface for a
configuration request that was sent on the User TX interface, it will be
indicated with a completion with the CMPL_STATUS field set to 2=CRS, and
the user will have to find the address and data values and send a new
transaction on the User TX interface. When the internal configuration
space returns a retry status during a configuration cycle (user_cscfg =
1) on the Command/Status interface, the pcie_cscrs will assert with the
pcie_csack signal to indicate the CRS status.
When the CRS Software Visibility Enable register in the Root Control
register is enabled, the IP will return the data value to 0x0001 for the
Vendor ID value and 0xffff (all 1’s) for the rest of the data in the
request for reads of offset 0 that return with CRS status. This is true
for both the User RX Interface and for the Command/Status interface.
When CRS Software Visibility is enabled, the CMPL_STATUS field of the
completion on the User RX Interface will not be 2=CRS and the pcie_cscrs
signal will not assert on the Command/Status interface.
The Stingray hardware never reissues configuration requests when it
receives CRS completions. Contrary to what sec 4.7.3.3 above says, when it
receives a CRS completion, it synthesizes 0xffff0001 data regardless of the
address of the read or the value of the CRS SV enable bit.
This is broken in two ways:
1) When CRS SV is disabled, the Root Port should never synthesize the
0x0001 value. If it receives a CRS completion, it should fail the
transaction and synthesize all 1's data.
2) When CRS SV is enabled, the Root Port should only synthesize 0x0001
data if it receives a CRS completion for a read of the Vendor ID. If it
receives a CRS completion for any other read, it should fail the
transaction and synthesize all 1's data.
This breaks pci_flr_wait(), which reads the Command register and expects to
see all 1's data if the read fails because of CRS completions. On
Stingray, it sees the incorrect 0xffff0001 data instead.
It also breaks config registers that contain the 0xffff0001 value. If we
read such a register, software can't distinguish a CRS completion from the
actual value read from the device.
On Stingray, if we read 0xffff0001 data, assume this indicates a CRS
completion and retry the read for 500ms. If we time out, return all 1's
(0xffffffff) data. Note that this corrupts registers that happen to
contain 0xffff0001.
Stingray advertises CRS SV support in its Root Capabilities register, and
the CRS SV enable bit is writable (even though the hardware ignores it).
Mask out PCI_EXP_RTCAP_CRSVIS so software doesn't try to use CRS SV.
Signed-off-by: Oza Pawandeep <oza.oza@broadcom.com>
[bhelgaas: changelog, add probe-time warning about corruption, don't
advertise CRS SV support, remove duplicate pci_generic_config_read32(),
fix alignment based on patch from Arnd Bergmann <arnd@arndb.de>]
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
|
|
Factor out the address calculation for memory-mapped config accesses as a
separate function. No functional change intended.
Signed-off-by: Oza Pawandeep <oza.oza@broadcom.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
|
|
Check the status of all lanes and idle the inactive one(s).
Tested-by: Jeffy Chen <jeffy.chen@rock-chips.com>
Signed-off-by: Shawn Lin <shawn.lin@rock-chips.com>
[bhelgaas: always set lanes_map, even for legacy_phy case]
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Brian Norris <briannorris@chromium.org>
Acked-by: Kishon Vijay Abraham I <kishon@ti.com>
|
|
We distinguish the legacy PHY from newer per-lane PHYs by adding legacy_phy
flag. Note that the legacy PHY is still the first option to be searched in
order not to break the backward compatibility of DTB.
Tested-by: Jeffy Chen <jeffy.chen@rock-chips.com>
Signed-off-by: Shawn Lin <shawn.lin@rock-chips.com>
[bhelgaas: tidy rockchip_pcie_get_phys()]
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Brian Norris <briannorris@chromium.org>
Acked-by: Kishon Vijay Abraham I <kishon@ti.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci
Pull PCI fix from Bjorn Helgaas:
"Remove needlessly alarming MSI affinity warning (this is not actually
a bug fix, but the warning prompts unnecessary bug reports)"
* tag 'pci-v4.13-fixes-3' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci:
PCI/MSI: Don't warn when irq_create_affinity_masks() returns NULL
|
|
irq_create_affinity_masks() can return NULL on non-SMP systems, when there
are not enough "free" vectors available to spread, or if memory allocation
for the CPU masks fails. Only the allocation failure is of interest, and
even then the system will work just fine except for non-optimally spread
vectors. Thus remove the warnings.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: David S. Miller <davem@davemloft.net>
|
|
Use a local "struct device *dev" for brevity and consistency in DPC driver.
No functional change intended.
Signed-off-by: Dongdong Liu <liudongdong3@huawei.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Keith Busch <keith.busch@intel.com>
|
|
Add eDPC support. Get and print the RP PIO error information when the
trigger condition is RP PIO error.
For more information on eDPC, please see PCI Express Base Specification
Revision 3.1, section 6.2.10.3, or view the PCI-SIG eDPC ECN here:
https://pcisig.com/sites/default/files/specification_documents/ECN_Enhanced_DPC_2012-11-19_final.pdf
Signed-off-by: Dongdong Liu <liudongdong3@huawei.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Keith Busch <keith.busch@intel.com>
|
|
Now that we have a custom printf format specifier, convert users of
full_name() to use %pOF instead. This is preparation for removing storing
of the full path string for each node.
Signed-off-by: Rob Herring <robh@kernel.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Tyrel Datwyler <tyreld@linux.vnet.ibm.com>
Cc: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Cc: Jason Cooper <jason@lakedaemon.net>
Cc: Thierry Reding <thierry.reding@gmail.com>
Cc: Jonathan Hunter <jonathanh@nvidia.com>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Michael Ellerman <mpe@ellerman.id.au>
|
|
Make this const as it is only stored in the type field of a device
structure, which is const. Done using Coccinelle.
Signed-off-by: Bhumika Goyal <bhumirks@gmail.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
|
|
Add support for the IPQ8074 PCIe controller. IPQ8074 supports Gen 1/2, one
lane, two PCIe root complex with support for MSI and legacy interrupts, and
it conforms to PCI Express Base 2.1 specification.
The core init is the similar to the existing SoC, however the clocks and
reset lines differ.
Signed-off-by: smuthayy <smuthayy@codeaurora.org>
Signed-off-by: Varadarajan Narayanan <varada@codeaurora.org>
[bhelgaas: fix capitalization and "dev" usage to match existing style]
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Stanimir Varbanov <svarbanov@mm-sol.com>
|
|
Presently, when support for a new SoC is added, the driver ops structures
and functions are versioned with plain 1, 2, 3 etc. Instead use the block
IP version number.
Signed-off-by: Varadarajan Narayanan <varada@codeaurora.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Stanimir Varbanov <svarbanov@mm-sol.com>
|
|
Commit a53e35db70d1 ("reset: Ensure drivers are explicit when requesting
reset lines") started to transition the reset control request API calls to
explicitly state whether the driver needs exclusive or shared reset control
behavior. Convert all drivers requesting exclusive resets to the explicit
API call so the temporary transition helpers can be removed.
No functional changes.
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Cc: Stanimir Varbanov <svarbanov@mm-sol.com>
|
|
The reset GPIO can be connected to a I2C or SPI IO expander, which may
sleep, so it is safer to use the gpiod_set_value_cansleep() variant
instead.
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Stanimir Varbanov <svarbanov@mm-sol.com>
|
|
If the interrupt status is cleared before it is handled, it is possible
that another interrupt will trigger while servicing the previous one. This
is causing timeouts in some wireless lan cards which use PCIe.
Clear MSI interrupt status after it gets serviced instead of before calling
generic_handler.
Signed-off-by: Faiz Abbas <faiz_abbas@ti.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-By: Joao Pinto <jpinto@synopsys.com>
|
|
platform_get_irq() returns an error code, but the pci-dra7xx driver ignores
it and always returns -EINVAL. This is not correct and prevents
-EPROBE_DEFER from being propagated properly.
Print and propagate the return value of platform_get_irq() on failure.
This issue was detected with the help of Coccinelle.
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Kishon Vijay Abraham I <kishon@ti.com>
|
|
Make this structure const as it is only stored in the ops field of a
pcie_port structure, which is of type const. Done using Coccinelle.
Signed-off-by: Bhumika Goyal <bhumirks@gmail.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
|
|
Make this structure const as it is only stored in the ops field of a
pcie_port structure, which is of type const. Done using Coccinelle.
Signed-off-by: Bhumika Goyal <bhumirks@gmail.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
|
|
When we enable a device, we first enable any upstream bridges. If a bridge
has multiple downstream devices and we enable them simultaneously, the race
to enable the upstream bridge may cause problems. Consider this hierarchy:
bridge A --+-- device B
+-- device C
If drivers for B and C call pci_enable_device() simultaneously, both will
attempt to enable A, which involves setting PCI_COMMAND_MASTER via
pci_set_master() and PCI_COMMAND_MEMORY via pci_enable_resources().
In the following sequence, B's update to set A's PCI_COMMAND_MEMORY is
lost, and neither B nor C will work correctly:
B C
pci_set_master(A)
cmd = read(A, PCI_COMMAND)
cmd |= PCI_COMMAND_MASTER
pci_set_master(A)
cmd = read(A, PCI_COMMAND)
cmd |= PCI_COMMAND_MASTER
write(A, PCI_COMMAND, cmd)
pci_enable_device(A)
pci_enable_resources(A)
cmd = read(A, PCI_COMMAND)
cmd |= PCI_COMMAND_MEMORY
write(A, PCI_COMMAND, cmd)
write(A, PCI_COMMAND, cmd)
Avoid this race by holding a new pci_bridge_mutex while enabling a bridge.
This ensures that both PCI_COMMAND_MASTER and PCI_COMMAND_MEMORY will be
updated before another thread can start enabling the bridge.
Note that although pci_enable_bridge() is recursive, it enables any
upstream bridges *before* acquiring the mutex. When it acquires the mutex
and calls pci_set_master() and pci_enable_device(), any upstream bridges
have already been enabled so pci_enable_device() will not deadlock by
calling pci_enable_bridge() again.
Signed-off-by: Srinath Mannam <srinath.mannam@broadcom.com>
[bhelgaas: changelog, comment]
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
|
|
If the pci_find_pcie_root_port() function is called on a root port
itself, return the root port rather than NULL.
This effectively reverts commit 0e405232871d6 ("PCI: fix oops when
try to find Root Port for a PCI device") which added an extra check
that would now be redundant.
Fixes: a99b646afa8a ("PCI: Disable PCIe Relaxed Ordering if unsupported")
Fixes: c56d4450eb68 ("PCI: Turn off Request Attributes to avoid Chelsio T5 Completion erratum")
Signed-off-by: Thierry Reding <treding@nvidia.com>
Acked-by: Bjorn Helgaas <bhelgaas@google.com>
Tested-by: Shawn Lin <shawn.lin@rock-chips.com>
Tested-by: Michael Ellerman <mpe@ellerman.id.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Some drivers (specifically the nes IB driver), want to create a lot of
sysfs driver attributes. Instead of open-coding the creation and
removal of these files (and getting it wrong btw), it's a better idea to
let the driver core handle all of this logic for us.
So add a new field to the pci driver structure, **groups, that allows
pci drivers to specify an attribute group list it wishes to have created
when it is registered with the driver core.
Big bonus is now the driver doesn't race with userspace when the sysfs
files are created vs. when the kobject is announced, so any script/tool
that actually wanted to use these files will not have to poll waiting
for them to show up.
Cc: Faisal Latif <faisal.latif@intel.com>
Cc: Doug Ledford <dledford@redhat.com>
Cc: Sean Hefty <sean.hefty@intel.com>
Cc: Hal Rosenstock <hal.rosenstock@gmail.com>
Cc: Bjorn Helgaas <bhelgaas@google.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Acked-by: Bjorn Helgaas <bhelgaas@google.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
|
|
Add an API to get "pci_epf_device_id" matching the EPF name. This can be
used by the EPF driver to get the driver data corresponding to the EPF
device name.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
[bhelgaas: folded in "while" loop termination fix from Colin Ian King
<colin.king@canonical.com>]
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
|
|
Use of_dma_configure() to set the initial DMA mask of EPF device. This
helps to get rid of "Coherent DMA mask 0x0 (pfn 0x0-0x1) covers a smaller
range of system memory than the DMA zone pfn" warning in certain platforms
like TI's K2G resulting in coherent DMA mask not being set.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
|
|
Switch from using custom MAX_LEGACY_IRQS and MAX_LEGACY_HOST_IRQS macros to
the generic PCI_NUM_INTX definition for the number of INTx interrupts.
Based-on-similar-patches-by: Paul Burton <paul.burton@imgtec.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Cc: Murali Karicheri <m-karicheri2@ti.com>
|
|
MAX_MSI_HOST_IRQS and MAX_LEGACY_HOST_IRQS are defined in both
pci-keystone.h (which is included by pci-keystone.c) and in pci-keystone.c
itself.
Remove the duplicate definitions from pci-keystone.c.
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Cc: Murali Karicheri <m-karicheri2@ti.com>
|
|
Allow the xilinx-pcie driver to be built on MIPS platforms which make use
of generic PCI drivers rather than legacy MIPS-specific interfaces. This
is used on the MIPS Boston development board.
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Cc: Bharat Kumar Gogada <bharatku@xilinx.com>
Cc: Michal Simek <michal.simek@xilinx.com>
Cc: Ravikiran Gummaluri <rgummal@xilinx.com>
|
|
The Xilinx AXI bridge for PCI Express device provides interrupts indicating
the completion of config space accesses. We have previously
enabled/unmasked them but do nothing with them besides acknowledge them.
Leave the interrupts masked in order to avoid servicing a large number of
pointless interrupts during boot.
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Cc: Bharat Kumar Gogada <bharatku@xilinx.com>
Cc: Michal Simek <michal.simek@xilinx.com>
Cc: Ravikiran Gummaluri <rgummal@xilinx.com>
|
|
The INTx & MSI interrupt decode paths duplicated a fair bit of common
functionality. They also strictly handled interrupts in order of INTx then
MSI, so if both types of interrupt were to be asserted simultaneously and
the MSI interrupt were first in the FIFO then the INTx code would read it &
ignore it before the MSI code then had to read it again, wasting the
original FIFO read.
Unify the INTx & MSI decode in order to reduce that duplication & allow a
single FIFO read to be performed for each interrupt regardless of its type.
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Cc: Bharat Kumar Gogada <bharatku@xilinx.com>
Cc: Michal Simek <michal.simek@xilinx.com>
Cc: Ravikiran Gummaluri <rgummal@xilinx.com>
|
|
The devicetree binding documentation for the Xilinx NWL PCIe root port
bridge shows an example which uses an interrupt-map property to map PCI
INTx interrupts to hardware IRQ numbers 1-4. The driver creates an IRQ
domain with size 4, which therefore covers the hwirq range 0-3.
This means that if we attempt to make use of the INTD interrupt then we're
likely to hit a WARN() in irq_domain_associate() because INTD, or hwirw=4,
is outside of the range covered by the IRQ domain. irq_domain_associate()
will then return -EINVAL and we'll be unable to make use of INTD.
Fix this by making use of the pci_irqd_intx_xlate() helper function to
translate the 1-4 range used in the DT to a 0-3 range used within the
driver, and stop adding 1 to decoded hwirq numbers.
Whilst cleaning up INTx handling we make use of the new PCI_NUM_INTX macro
& drop the custom INTX definitions.
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Cc: Michal Simek <michal.simek@xilinx.com>
Cc: "Sören Brinkmann" <soren.brinkmann@xilinx.com>
|
|
The pcie-xilinx driver creates an IRQ domain of size 4 for legacy PCI INTx
interrupts, which at first glance seems reasonable since there are 4
possible such interrupts. Unfortunately the driver then proceeds to use the
range 1-4 as the hwirq numbers for INTA-INTD, causing warnings & broken
interrupts when attempting to use INTD/hwirq=4 due to it being beyond the
range of the IRQ domain:
WARNING: CPU: 0 PID: 1 at kernel/irq/irqdomain.c:365
irq_domain_associate+0x170/0x220
error: hwirq 0x4 is too large for dummy
Modules linked in:
CPU: 0 PID: 1 Comm: swapper/0 Tainted: G W
4.12.0-rc5-00126-g19e1b3a10aad-dirty #427
Stack : 0000000000000000 0000000000000004 0000000000000006 ffffffff8092c78a
0000000000000061 ffffffff8018bf60 0000000000000000 0000000000000000
ffffffff8088c287 ffffffff80811d18 a8000000ffc60000 ffffffff80926678
0000000000000001 0000000000000000 ffffffff80887880 ffffffff80960000
ffffffff80920000 ffffffff801e6744 ffffffff80887880 a8000000ffc4f8f8
000000000000089c ffffffff8018d260 0000000000010000 ffffffff80811d18
0000000000000000 0000000000000001 0000000000000000 0000000000000000
0000000000000000 a8000000ffc4f840 0000000000000000 ffffffff8042cf34
0000000000000000 0000000000000000 0000000000000000 0000000000040c00
0000000000000000 ffffffff8010d1c8 0000000000000000 ffffffff8042cf34
...
Call Trace:
[<ffffffff8010d1c8>] show_stack+0x80/0xa0
[<ffffffff8042cf34>] dump_stack+0xd4/0x110
[<ffffffff8013ea98>] __warn+0xf0/0x108
[<ffffffff8013eb14>] warn_slowpath_fmt+0x3c/0x48
[<ffffffff80196528>] irq_domain_associate+0x170/0x220
[<ffffffff80196bf0>] irq_create_mapping+0x88/0x118
[<ffffffff801976a8>] irq_create_fwspec_mapping+0xb8/0x320
[<ffffffff80197970>] irq_create_of_mapping+0x60/0x70
[<ffffffff805d1318>] of_irq_parse_and_map_pci+0x20/0x38
[<ffffffff8049c210>] pci_fixup_irqs+0x60/0xe0
[<ffffffff8049cd64>] xilinx_pcie_probe+0x28c/0x478
[<ffffffff804e8ca8>] platform_drv_probe+0x50/0xd0
[<ffffffff804e73a4>] driver_probe_device+0x2c4/0x3a0
[<ffffffff804e7544>] __driver_attach+0xc4/0xd0
[<ffffffff804e5254>] bus_for_each_dev+0x64/0xa8
[<ffffffff804e5e40>] bus_add_driver+0x1f0/0x268
[<ffffffff804e8000>] driver_register+0x68/0x118
[<ffffffff801001a4>] do_one_initcall+0x4c/0x178
[<ffffffff808d3ca8>] kernel_init_freeable+0x204/0x2b0
[<ffffffff80730b68>] kernel_init+0x10/0xf8
[<ffffffff80106218>] ret_from_kernel_thread+0x14/0x1c
Fix this by making use of the new pci_irqd_intx_xlate() helper to translate
the INTx 1-4 range into the 0-3 range suitable for the IRQ domain of size
4, and stop adding 1 to the hwirq number decoded from the interrupt FIFO
which is already in the range 0-3.
Whilst we're here we switch to using PCI_NUM_INTX rather than the magic
number 4, making it clearer what the 4 means.
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Cc: Bharat Kumar Gogada <bharatku@xilinx.com>
Cc: Michal Simek <michal.simek@xilinx.com>
Cc: Ravikiran Gummaluri <rgummal@xilinx.com>
|
|
We plan to introduce per-lane PHYs, so factor out rockchip_pcie_get_phys()
to make it easier in the future. No functional change intended.
Tested-by: Jeffy Chen <jeffy.chen@rock-chips.com>
Signed-off-by: Shawn Lin <shawn.lin@rock-chips.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Brian Norris <briannorris@chromium.org>
Acked-by: Kishon Vijay Abraham I <kishon@ti.com>
|
|
Get vpcie12v from DT and control it if available.
Signed-off-by: Shawn Lin <shawn.lin@rock-chips.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
|
|
The ks_pcie and pci variables in ks_dw_pcie_msi_irq_mask() and
ks_dw_pcie_msi_irq_unmask() are never used. Remove them.
Signed-off-by: Shawn Lin <shawn.lin@rock-chips.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
|
|
Use the PCI_NUM_INTX macro to indicate the number of PCI INTx interrupts
rather than the magic number 4. This makes it clearer where the number
comes from & what it relates to.
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
|
|
of_irq_get() may return a negative error number as well as 0 on failure,
while the driver only checks for 0, blithely continuing with the call to
irq_set_chained_handler_and_data() -- that function expects *unsigned int*
so should probably do nothing when a large IRQ number resulting from a
conversion of a negative error number is passed to it. The driver then
probes successfully while being only partly functional...
Check for 'irq <= 0' instead and propagate the negative error number to the
probe method -- that will allow the deferred probing as well.
Fixes: d3c68e0a7e34 ("PCI: faraday: Add Faraday Technology FTPCI100 PCI Host Bridge driver")
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
|
