| Age | Commit message (Collapse) | Author |
|---|
|
[ Upstream commit 86f271f22bbb6391410a07e08d6ca3757fda01fa ]
Errata #i2037 in AM65x/DRA80xM Processors Silicon Revision 1.0
(SPRZ452D_July 2018_Revised December 2019 [1]) mentions when an
inbound PCIe TLP spans more than two internal AXI 128-byte bursts,
the bus may corrupt the packet payload and the corrupt data may
cause associated applications or the processor to hang.
The workaround for Errata #i2037 is to limit the maximum read
request size and maximum payload size to 128 bytes. Add workaround
for Errata #i2037 here.
The errata and workaround is applicable only to AM65x SR 1.0 and
later versions of the silicon will have this fixed.
[1] -> https://www.ti.com/lit/er/sprz452i/sprz452i.pdf
Link: https://lore.kernel.org/linux-pci/16e1fcae-1ea7-46be-b157-096e05661b15@siemens.com
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Achal Verma <a-verma1@ti.com>
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Signed-off-by: Jan Kiszka <jan.kiszka@siemens.com>
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Reviewed-by: Siddharth Vadapalli <s-vadapalli@ti.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit a9927c2cac6e9831361e43a14d91277818154e6a ]
If IORESOURCE_BUS is not provided in Device Tree it will be fabricated in
of_pci_parse_bus_range(), so NULL pointer dereference should not happen
here.
But that's hard to verify, so check for NULL anyway.
Found by Linux Verification Center (linuxtesting.org) with SVACE.
Link: https://lore.kernel.org/linux-pci/20240503125705.46055-1-amishin@t-argos.ru
Suggested-by: Bjorn Helgaas <helgaas@kernel.org>
Signed-off-by: Aleksandr Mishin <amishin@t-argos.ru>
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
[bhelgaas: commit log]
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
commit a4bbcac11d3cea85822af8b40daed7e96bca5068 upstream.
The LS7A chipset can be used as part of a PCIe Root Complex with
Loongson-3C6000 and similar CPUs. In this case, DEV_LS7A_PCIE_PORT5 has a
PCI_CLASS_BRIDGE_HOST class code, and it is a Type 0 Function whose config
space provides access to Root Complex registers.
The DEV_LS7A_PCIE_PORT5 has an MSI Capability, and its MSI Enable bit must
be set before other devices below the Root Complex can use MSI. This is
not the standard PCI behavior of MSI Enable, so the normal PCI MSI code
does not set it.
Set the DEV_LS7A_PCIE_PORT5 MSI Enable bit via a quirk so other devices
below the Root Complex can use MSI.
[kwilczynski: exit early to reduce indentation; commit log]
Link: https://lore.kernel.org/linux-pci/20240612065315.2048110-1-chenhuacai@loongson.cn
Signed-off-by: Sheng Wu <wusheng@loongson.cn>
Signed-off-by: Huacai Chen <chenhuacai@loongson.cn>
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
[bhelgaas: commit log]
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Cc: stable@vger.kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 840b7a5edf88fe678c60dee88a135647c0ea4375 upstream.
Rockchip platforms use 'GPIO_ACTIVE_HIGH' flag in the devicetree definition
for ep_gpio. This means, whatever the logical value set by the driver for
the ep_gpio, physical line will output the same logic level.
For instance,
gpiod_set_value_cansleep(rockchip->ep_gpio, 0); --> Level low
gpiod_set_value_cansleep(rockchip->ep_gpio, 1); --> Level high
But while requesting the ep_gpio, GPIOD_OUT_HIGH flag is currently used.
Now, this also causes the physical line to output 'high' creating trouble
for endpoint devices during host reboot.
When host reboot happens, the ep_gpio will initially output 'low' due to
the GPIO getting reset to its POR value. Then during host controller probe,
it will output 'high' due to GPIOD_OUT_HIGH flag. Then during
rockchip_pcie_host_init_port(), it will first output 'low' and then 'high'
indicating the completion of controller initialization.
On the endpoint side, each output 'low' of ep_gpio is accounted for PERST#
assert and 'high' for PERST# deassert. With the above mentioned flow during
host reboot, endpoint will witness below state changes for PERST#:
(1) PERST# assert - GPIO POR state
(2) PERST# deassert - GPIOD_OUT_HIGH while requesting GPIO
(3) PERST# assert - rockchip_pcie_host_init_port()
(4) PERST# deassert - rockchip_pcie_host_init_port()
Now the time interval between (2) and (3) is very short as both happen
during the driver probe(), and this results in a race in the endpoint.
Because, before completing the PERST# deassertion in (2), endpoint got
another PERST# assert in (3).
A proper way to fix this issue is to change the GPIOD_OUT_HIGH flag in (2)
to GPIOD_OUT_LOW. Because the usual convention is to request the GPIO with
a state corresponding to its 'initial/default' value and let the driver
change the state of the GPIO when required.
As per that, the ep_gpio should be requested with GPIOD_OUT_LOW as it
corresponds to the POR value of '0' (PERST# assert in the endpoint). Then
the driver can change the state of the ep_gpio later in
rockchip_pcie_host_init_port() as per the initialization sequence.
This fixes the firmware crash issue in Qcom based modems connected to
Rockpro64 based board.
Fixes: e77f847df54c ("PCI: rockchip: Add Rockchip PCIe controller support")
Closes: https://lore.kernel.org/mhi/20240402045647.GG2933@thinkpad/
Link: https://lore.kernel.org/linux-pci/20240416-pci-rockchip-perst-fix-v1-1-4800b1d4d954@linaro.org
Reported-by: Slark Xiao <slark_xiao@163.com>
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Niklas Cassel <cassel@kernel.org>
Cc: stable@vger.kernel.org # v4.9
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 28b8d7793b8573563b3d45321376f36168d77b1e upstream.
PERST# is active low according to the PCIe specification.
However, the existing pcie-dw-rockchip.c driver does:
gpiod_set_value(..., 0); msleep(100); gpiod_set_value(..., 1);
when asserting + deasserting PERST#.
This is of course wrong, but because all the device trees for this
compatible string have also incorrectly marked this GPIO as ACTIVE_HIGH:
$ git grep -B 10 reset-gpios arch/arm64/boot/dts/rockchip/rk3568*
$ git grep -B 10 reset-gpios arch/arm64/boot/dts/rockchip/rk3588*
The actual toggling of PERST# is correct, and we cannot change it anyway,
since that would break device tree compatibility.
However, this driver does request the GPIO to be initialized as
GPIOD_OUT_HIGH, which does cause a silly sequence where PERST# gets
toggled back and forth for no good reason.
Fix this by requesting the GPIO to be initialized as GPIOD_OUT_LOW (which
for this driver means PERST# asserted).
This will avoid an unnecessary signal change where PERST# gets deasserted
(by devm_gpiod_get_optional()) and then gets asserted (by
rockchip_pcie_start_link()) just a few instructions later.
Before patch, debug prints on EP side, when booting RC:
[ 845.606810] pci: PERST# asserted by host!
[ 852.483985] pci: PERST# de-asserted by host!
[ 852.503041] pci: PERST# asserted by host!
[ 852.610318] pci: PERST# de-asserted by host!
After patch, debug prints on EP side, when booting RC:
[ 125.107921] pci: PERST# asserted by host!
[ 132.111429] pci: PERST# de-asserted by host!
This extra, very short, PERST# assertion + deassertion has been reported to
cause issues with certain WLAN controllers, e.g. RTL8822CE.
Fixes: 0e898eb8df4e ("PCI: rockchip-dwc: Add Rockchip RK356X host controller driver")
Link: https://lore.kernel.org/linux-pci/20240417164227.398901-1-cassel@kernel.org
Tested-by: Heiko Stuebner <heiko@sntech.de>
Tested-by: Jianfeng Liu <liujianfeng1994@gmail.com>
Signed-off-by: Niklas Cassel <cassel@kernel.org>
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Heiko Stuebner <heiko@sntech.de>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Cc: stable@vger.kernel.org # v5.15+
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit fea93a3e5d5e6a09eb153866d2ce60ea3287a70d upstream.
The intent of the code snippet is to always return 0 for both
PCI_INTERRUPT_LINE and PCI_INTERRUPT_PIN.
The check misses PCI_INTERRUPT_PIN. This patch fixes that.
This is discovered by this call in VFIO:
pci_read_config_byte(vdev->pdev, PCI_INTERRUPT_PIN, &pin);
The old code does not set *val to 0 because it misses the check for
PCI_INTERRUPT_PIN. Garbage is returned in that case.
Fixes: 4daace0d8ce8 ("PCI: hv: Add paravirtual PCI front-end for Microsoft Hyper-V VMs")
Link: https://lore.kernel.org/linux-pci/20240701202606.129606-1-wei.liu@kernel.org
Signed-off-by: Wei Liu <wei.liu@kernel.org>
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Reviewed-by: Michael Kelley <mhklinux@outlook.com>
Cc: stable@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit c2a57ee0f2f1ad8c970ff58b78a43e85abbdeb7f ]
When PERST# assert and deassert happens on the PERST# supported platforms,
both iATU0 and iATU6 will map inbound window to BAR0. DMA will access the
area that was previously allocated (iATU0) for BAR0, instead of the new
area (iATU6) for BAR0.
Right now, this isn't an issue because both iATU0 and iATU6 should
translate inbound accesses to BAR0 to the same allocated memory area.
However, having two separate inbound mappings for the same BAR is a
disaster waiting to happen.
The mappings between PCI BAR and iATU inbound window are maintained in the
dw_pcie_ep::bar_to_atu[] array. While allocating a new inbound iATU map for
a BAR, dw_pcie_ep_inbound_atu() API checks for the availability of the
existing mapping in the array and if it is not found (i.e., value in the
array indexed by the BAR is found to be 0), it allocates a new map value
using find_first_zero_bit().
The issue is the existing logic failed to consider the fact that the map
value '0' is a valid value for BAR0, so find_first_zero_bit() will return
'0' as the map value for BAR0 (note that it returns the first zero bit
position).
Due to this, when PERST# assert + deassert happens on the PERST# supported
platforms, the inbound window allocation restarts from BAR0 and the
existing logic to find the BAR mapping will return '6' for BAR0 instead of
'0' due to the fact that it considers '0' as an invalid map value.
Fix this issue by always incrementing the map value before assigning to
bar_to_atu[] array and then decrementing it while fetching. This will make
sure that the map value '0' always represents the invalid mapping."
Fixes: 4284c88fff0e ("PCI: designware-ep: Allow pci_epc_set_bar() update inbound map address")
Closes: https://lore.kernel.org/linux-pci/ZXsRp+Lzg3x%2Fnhk3@x1-carbon/
Link: https://lore.kernel.org/linux-pci/20240412160841.925927-1-Frank.Li@nxp.com
Reported-by: Niklas Cassel <Niklas.Cassel@wdc.com>
Tested-by: Niklas Cassel <niklas.cassel@wdc.com>
Signed-off-by: Frank Li <Frank.Li@nxp.com>
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Reviewed-by: Niklas Cassel <niklas.cassel@wdc.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 912315715d7b74f7abdb6f063ebace44ee288af9 ]
All EP specific resources are enabled during PERST# deassert. As a counter
operation, all resources should be disabled during PERST# assert. There is
no point in skipping that if the link was not enabled.
This will also result in enablement of the resources twice if PERST# got
deasserted again. So remove the check from qcom_pcie_perst_assert() and
disable all the resources unconditionally.
Fixes: f55fee56a631 ("PCI: qcom-ep: Add Qualcomm PCIe Endpoint controller driver")
Link: https://lore.kernel.org/linux-pci/20240430-pci-epf-rework-v4-1-22832d0d456f@linaro.org
Tested-by: Niklas Cassel <cassel@kernel.org>
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Niklas Cassel <cassel@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit c93637e6a4c4e1d0e85ef7efac78d066bbb24d96 ]
Avoid large backtrace, it is sufficient to warn the user that there has
been a link problem. Either the link has failed and the system is in need
of maintenance, or the link continues to work and user has been informed.
The message from the warning can be looked up in the sources.
This makes an actual link issue less verbose.
First of all, this controller has a limitation in that the controller
driver has to assist the hardware with transition to L1 link state by
writing L1IATN to PMCTRL register, the L1 and L0 link state switching
is not fully automatic on this controller.
In case of an ASMedia ASM1062 PCIe SATA controller which does not support
ASPM, on entry to suspend or during platform pm_test, the SATA controller
enters D3hot state and the link enters L1 state. If the SATA controller
wakes up before rcar_pcie_wakeup() was called and returns to D0, the link
returns to L0 before the controller driver even started its transition to
L1 link state. At this point, the SATA controller did send an PM_ENTER_L1
DLLP to the PCIe controller and the PCIe controller received it, and the
PCIe controller did set PMSR PMEL1RX bit.
Once rcar_pcie_wakeup() is called, if the link is already back in L0 state
and PMEL1RX bit is set, the controller driver has no way to determine if
it should perform the link transition to L1 state, or treat the link as if
it is in L0 state. Currently the driver attempts to perform the transition
to L1 link state unconditionally, which in this specific case fails with a
PMSR L1FAEG poll timeout, however the link still works as it is already
back in L0 state.
Reduce this warning verbosity. In case the link is really broken, the
rcar_pcie_config_access() would fail, otherwise it will succeed and any
system with this controller and ASM1062 can suspend without generating
a backtrace.
Fixes: 84b576146294 ("PCI: rcar: Finish transition to L1 state in rcar_pcie_config_access()")
Link: https://lore.kernel.org/linux-pci/20240511235513.77301-1-marek.vasut+renesas@mailbox.org
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
ks_pcie_setup_rc_app_regs()
[ Upstream commit a231707a91f323af1e5d9f1722055ec2fc1c7775 ]
If IORESOURCE_MEM is not provided in Device Tree due to
any error, resource_list_first_type() will return NULL and
pci_parse_request_of_pci_ranges() will just emit a warning.
This will cause a NULL pointer dereference. Fix this bug by adding NULL
return check.
Found by Linux Verification Center (linuxtesting.org) with SVACE.
Fixes: 0f71c60ffd26 ("PCI: dwc: Remove storing of PCI resources")
Link: https://lore.kernel.org/linux-pci/20240505061517.11527-1-amishin@t-argos.ru
Suggested-by: Bjorn Helgaas <helgaas@kernel.org>
Suggested-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Aleksandr Mishin <amishin@t-argos.ru>
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 9ffa0e70b2daf9b0271e4960b7c8a2350e2cda08 ]
After 6ab15b5e7057 ("PCI: dwc: keystone: Convert .scan_bus() callback to
use add_bus"), ks_pcie_v3_65_add_bus() enabled BAR 0 for both v3.65a and
v4.90a devices. On the AM654x SoC, which uses v4.90a, enabling BAR 0
causes Completion Timeouts when setting up MSI-X. These timeouts delay
boot of the AM654x by about 45 seconds.
Move the BAR 0 initialization to ks_pcie_msi_host_init(), which is only
used for v3.65a devices, and remove ks_pcie_v3_65_add_bus().
[bhelgaas: commit log]
Fixes: 6ab15b5e7057 ("PCI: dwc: keystone: Convert .scan_bus() callback to use add_bus")
Link: https://lore.kernel.org/linux-pci/20240328085041.2916899-3-s-vadapalli@ti.com
Suggested-by: Bjorn Helgaas <helgaas@kernel.org>
Suggested-by: Niklas Cassel <cassel@kernel.org>
Suggested-by: Serge Semin <fancer.lancer@gmail.com>
Signed-off-by: Siddharth Vadapalli <s-vadapalli@ti.com>
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Niklas Cassel <cassel@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 5125fdc3292eea20870d4e6cefa62dc1245ce7ec ]
Relocate ks_pcie_set_dbi_mode() and ks_pcie_clear_dbi_mode() to avoid
forward declaration in a subsequent patch. No functional change intended.
Link: https://lore.kernel.org/linux-pci/20240328085041.2916899-2-s-vadapalli@ti.com
Signed-off-by: Siddharth Vadapalli <s-vadapalli@ti.com>
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Stable-dep-of: 9ffa0e70b2da ("PCI: keystone: Don't enable BAR 0 for AM654x")
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
commit 2dba285caba53f309d6060fca911b43d63f41697 upstream.
Remove wrong mask on subsys_vendor_id. Both the Vendor ID and Subsystem
Vendor ID are u16 variables and are written to a u32 register of the
controller. The Subsystem Vendor ID was always 0 because the u16 value
was masked incorrectly with GENMASK(31,16) resulting in all lower 16
bits being set to 0 prior to the shift.
Remove both masks as they are unnecessary and set the register correctly
i.e., the lower 16-bits are the Vendor ID and the upper 16-bits are the
Subsystem Vendor ID.
This is documented in the RK3399 TRM section 17.6.7.1.17
[kwilczynski: removed unnecesary newline]
Fixes: cf590b078391 ("PCI: rockchip: Add EP driver for Rockchip PCIe controller")
Link: https://lore.kernel.org/linux-pci/20240403144508.489835-1-rick.wertenbroek@gmail.com
Signed-off-by: Rick Wertenbroek <rick.wertenbroek@gmail.com>
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Damien Le Moal <dlemoal@kernel.org>
Cc: stable@vger.kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit 19326006a21da26532d982254677c892dae8f29b ]
Tegra194 PCIe probe path is taking failure path in success case for
Endpoint mode. Return success from the switch case instead of going
into the failure path.
Fixes: c57247f940e8 ("PCI: tegra: Add support for PCIe endpoint mode in Tegra194")
Link: https://lore.kernel.org/linux-pci/20240408093053.3948634-1-vidyas@nvidia.com
Signed-off-by: Vidya Sagar <vidyas@nvidia.com>
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Reviewed-by: Jon Hunter <jonathanh@nvidia.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit b5ff74c1ef50fe08e384026875fec660fadfaedd ]
For a physical PCI device that is passed through to a Hyper-V guest VM,
current code specifies the VMBus ring buffer size as 4 pages. But this
is an inappropriate dependency, since the amount of ring buffer space
needed is unrelated to PAGE_SIZE. For example, on x86 the ring buffer
size ends up as 16 Kbytes, while on ARM64 with 64 Kbyte pages, the ring
size bloats to 256 Kbytes. The ring buffer for PCI pass-thru devices
is used for only a few messages during device setup and removal, so any
space above a few Kbytes is wasted.
Fix this by declaring the ring buffer size to be a fixed 16 Kbytes.
Furthermore, use the VMBUS_RING_SIZE() macro so that the ring buffer
header is properly accounted for, and so the size is rounded up to a
page boundary, using the page size for which the kernel is built. While
w/64 Kbyte pages this results in a 64 Kbyte ring buffer header plus a
64 Kbyte ring buffer, that's the smallest possible with that page size.
It's still 128 Kbytes better than the current code.
Link: https://lore.kernel.org/linux-pci/20240216202240.251818-1-mhklinux@outlook.com
Signed-off-by: Michael Kelley <mhklinux@outlook.com>
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Reviewed-by: Kuppuswamy Sathyanarayanan <sathyanarayanan.kuppuswamy@linux.intel.com>
Reviewed-by: Ilpo Jarvinen <ilpo.jarvinen@linux.intel.com>
Reviewed-by: Long Li <longli@microsoft.com>
Cc: <stable@vger.kernel.org> # 5.15.x
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 72e34b8593e08a0ee759b7a038e0b178418ea6f8 ]
The commit message in commit fc9a77040b04 ("PCI: designware-ep: Configure
Resizable BAR cap to advertise the smallest size") claims that it modifies
the Resizable BAR capability to only advertise support for 1 MB size BARs.
However, the commit writes all zeroes to PCI_REBAR_CAP (the register which
contains the possible BAR sizes that a BAR be resized to).
According to the spec, it is illegal to not have a bit set in
PCI_REBAR_CAP, and 1 MB is the smallest size allowed.
Set bit 4 in PCI_REBAR_CAP, so that we actually advertise support for a
1 MB BAR size.
Before:
Capabilities: [2e8 v1] Physical Resizable BAR
BAR 0: current size: 1MB
BAR 1: current size: 1MB
BAR 2: current size: 1MB
BAR 3: current size: 1MB
BAR 4: current size: 1MB
BAR 5: current size: 1MB
After:
Capabilities: [2e8 v1] Physical Resizable BAR
BAR 0: current size: 1MB, supported: 1MB
BAR 1: current size: 1MB, supported: 1MB
BAR 2: current size: 1MB, supported: 1MB
BAR 3: current size: 1MB, supported: 1MB
BAR 4: current size: 1MB, supported: 1MB
BAR 5: current size: 1MB, supported: 1MB
Fixes: fc9a77040b04 ("PCI: designware-ep: Configure Resizable BAR cap to advertise the smallest size")
Link: https://lore.kernel.org/linux-pci/20240307111520.3303774-1-cassel@kernel.org
Signed-off-by: Niklas Cassel <cassel@kernel.org>
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Cc: <stable@vger.kernel.org> # 5.2
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit bf79e33cdd89db498e00a6131e937259de5f2705 ]
Qcom SoCs making use of ARM SMMU require BDF to SID translation table in
the driver to properly map the SID for the PCIe devices based on their BDF
identifier. This is currently achieved with the help of
qcom_pcie_config_sid_1_9_0() function for SoCs supporting the 1_9_0 config.
But With newer Qcom SoCs starting from SM8450, BDF to SID translation is
set to bypass mode by default in hardware. Due to this, the translation
table that is set in the qcom_pcie_config_sid_1_9_0() is essentially
unused and the default SID is used for all endpoints in SoCs starting from
SM8450.
This is a security concern and also warrants swapping the DeviceID in DT
while using the GIC ITS to handle MSIs from endpoints. The swapping is
currently done like below in DT when using GIC ITS:
/*
* MSIs for BDF (1:0.0) only works with Device ID 0x5980.
* Hence, the IDs are swapped.
*/
msi-map = <0x0 &gic_its 0x5981 0x1>,
<0x100 &gic_its 0x5980 0x1>;
Here, swapping of the DeviceIDs ensure that the endpoint with BDF (1:0.0)
gets the DeviceID 0x5980 which is associated with the default SID as per
the iommu mapping in DT. So MSIs were delivered with IDs swapped so far.
But this also means the Root Port (0:0.0) won't receive any MSIs (for PME,
AER etc...)
So let's fix these issues by clearing the BDF to SID bypass mode for all
SoCs making use of the 1_9_0 config. This allows the PCIe devices to use
the correct SID, thus avoiding the DeviceID swapping hack in DT and also
achieving the isolation between devices.
Fixes: 4c9398822106 ("PCI: qcom: Add support for configuring BDF to SID mapping for SM8250")
Link: https://lore.kernel.org/linux-pci/20240307-pci-bdf-sid-fix-v1-1-9423a7e2d63c@linaro.org
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Cc: stable@vger.kernel.org # 5.11
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 039741a8d7c9a01c1bc84a5ac5aa770a5e138a30 ]
The MDIO_WT_DONE() macro tests bit 31, which is always 0 (== done) as
readw_poll_timeout_atomic() does a 16-bit read. Replace with the readl
variant.
[kwilczynski: commit log]
Fixes: ca5dcc76314d ("PCI: brcmstb: Replace status loops with read_poll_timeout_atomic()")
Link: https://lore.kernel.org/linux-pci/20240217133722.14391-1-wahrenst@gmx.net
Signed-off-by: Jonathan Bell <jonathan@raspberrypi.com>
Signed-off-by: Stefan Wahren <wahrenst@gmx.net>
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Acked-by: Florian Fainelli <florian.fainelli@broadcom.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
commit b5d1b4b46f856da1473c7ba9a5cdfcb55c9b2478 upstream.
The "msg_addr" variable is u64. However, the "aligned_offset" is an
unsigned int. This means that when the code does:
msg_addr &= ~aligned_offset;
it will unintentionally zero out the high 32 bits. Use ALIGN_DOWN() to do
the alignment instead.
Fixes: 2217fffcd63f ("PCI: dwc: endpoint: Fix dw_pcie_ep_raise_msix_irq() alignment support")
Link: https://lore.kernel.org/r/af59c7ad-ab93-40f7-ad4a-7ac0b14d37f5@moroto.mountain
Signed-off-by: Dan Carpenter <dan.carpenter@linaro.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Niklas Cassel <cassel@kernel.org>
Reviewed-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Cc: <stable@vger.kernel.org>
Signed-off-by: Niklas Cassel <cassel@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit 9ccc1318cf4bd90601f221268e42c3374703d681 ]
When using the fls() helper, the translation table should be a power of
two; otherwise, the resulting value will not be correct.
For example, given fls(0x3e00000) - 1 = 25, the PCIe translation window
size will be set to 0x2000000 instead of the expected size 0x3e00000.
Fix the translation window by splitting the MMIO space into multiple tables
if its size is not a power of two.
[kwilczynski: commit log]
Link: https://lore.kernel.org/linux-pci/20231023081423.18559-1-jianjun.wang@mediatek.com
Fixes: d3bf75b579b9 ("PCI: mediatek-gen3: Add MediaTek Gen3 driver for MT8192")
Signed-off-by: Jianjun Wang <jianjun.wang@mediatek.com>
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit c12ca110c613a81cb0f0099019c839d078cd0f38 ]
The PCI driver invokes the PHY APIs using the ks_pcie_enable_phy()
function. The PHY in this case is the Serdes. It is possible that the
PCI instance is configured for two lane operation across two different
Serdes instances, using one lane of each Serdes.
In such a configuration, if the reference clock for one Serdes is
provided by the other Serdes, it results in a race condition. After the
Serdes providing the reference clock is initialized by the PCI driver by
invoking its PHY APIs, it is not guaranteed that this Serdes remains
powered on long enough for the PHY APIs based initialization of the
dependent Serdes. In such cases, the PLL of the dependent Serdes fails
to lock due to the absence of the reference clock from the former Serdes
which has been powered off by the PM Core.
Fix this by obtaining reference to the PHYs before invoking the PHY
initialization APIs and releasing reference after the initialization is
complete.
Link: https://lore.kernel.org/linux-pci/20230927041845.1222080-1-s-vadapalli@ti.com
Fixes: 49229238ab47 ("PCI: keystone: Cleanup PHY handling")
Signed-off-by: Siddharth Vadapalli <s-vadapalli@ti.com>
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Acked-by: Ravi Gunasekaran <r-gunasekaran@ti.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
commit 4e11c29873a8a296a20f99b3e03095e65ebf897d upstream.
We found a failure when using the iperf tool during WiFi performance
testing, where some MSIs were received while clearing the interrupt
status, and these MSIs cannot be serviced.
The interrupt status can be cleared even if the MSI status remains pending.
As such, given the edge-triggered interrupt type, its status should be
cleared before being dispatched to the handler of the underling device.
[kwilczynski: commit log, code comment wording]
Link: https://lore.kernel.org/linux-pci/20231211094923.31967-1-jianjun.wang@mediatek.com
Fixes: 43e6409db64d ("PCI: mediatek: Add MSI support for MT2712 and MT7622")
Signed-off-by: qizhong cheng <qizhong.cheng@mediatek.com>
Signed-off-by: Jianjun Wang <jianjun.wang@mediatek.com>
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
[bhelgaas: rewrap comment]
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 2217fffcd63f86776c985d42e76daa43a56abdf1 upstream.
Commit 6f5e193bfb55 ("PCI: dwc: Fix dw_pcie_ep_raise_msix_irq() to get
correct MSI-X table address") modified dw_pcie_ep_raise_msix_irq() to
support iATUs which require a specific alignment.
However, this support cannot have been properly tested.
The whole point is for the iATU to map an address that is aligned,
using dw_pcie_ep_map_addr(), and then let the writel() write to
ep->msi_mem + aligned_offset.
Thus, modify the address that is mapped such that it is aligned.
With this change, dw_pcie_ep_raise_msix_irq() matches the logic in
dw_pcie_ep_raise_msi_irq().
Link: https://lore.kernel.org/linux-pci/20231128132231.2221614-1-nks@flawful.org
Fixes: 6f5e193bfb55 ("PCI: dwc: Fix dw_pcie_ep_raise_msix_irq() to get correct MSI-X table address")
Signed-off-by: Niklas Cassel <niklas.cassel@wdc.com>
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Cc: stable@vger.kernel.org # 5.7
Cc: Kishon Vijay Abraham I <kishon@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 49de0dc87965079a8e2803ee4b39f9d946259423 upstream.
The vmd_pm_enable_quirk() helper is called from pci_walk_bus() during
probe to enable ASPM for controllers with VMD_FEAT_BIOS_PM_QUIRK set.
Since pci_walk_bus() already holds a pci_bus_sem read lock, use
pci_enable_link_state_locked() to enable link states in order to avoid a
potential deadlock (e.g. in case someone takes a write lock before
reacquiring the read lock).
Fixes: f492edb40b54 ("PCI: vmd: Add quirk to configure PCIe ASPM and LTR")
Link: https://lore.kernel.org/r/20231128081512.19387-3-johan+linaro@kernel.org
Signed-off-by: Johan Hovold <johan+linaro@kernel.org>
[bhelgaas: add "potential" in subject since the deadlock has only been
reported by lockdep, include helper name in commit log]
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Cc: <stable@vger.kernel.org> # 6.3
Cc: Michael Bottini <michael.a.bottini@linux.intel.com>
Cc: David E. Box <david.e.box@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit ef61a0405742a9f7f6051bc6fd2f017d87d07911 upstream.
This is a partial revert of 8b3517f88ff2 ("PCI: loongson: Prevent LS7A MRRS
increases") for MIPS-based Loongson.
Some MIPS Loongson systems don't support arbitrary Max_Read_Request_Size
(MRRS) settings. 8b3517f88ff2 ("PCI: loongson: Prevent LS7A MRRS
increases") worked around that by (1) assuming that firmware configured
MRRS to the maximum supported value and (2) preventing the PCI core from
increasing MRRS.
Unfortunately, some firmware doesn't set that maximum MRRS correctly, which
results in devices not being initialized correctly. One symptom, from the
Debian report below, is this:
ata4.00: exception Emask 0x0 SAct 0x20000000 SErr 0x0 action 0x6 frozen
ata4.00: failed command: WRITE FPDMA QUEUED
ata4.00: cmd 61/20:e8:00:f0:e1/00:00:00:00:00/40 tag 29 ncq dma 16384 out
res 40/00:00:00:00:00/00:00:00:00:00/00 Emask 0x4 (timeout)
ata4.00: status: { DRDY }
ata4: hard resetting link
Limit MRRS to 256 because MIPS Loongson with higher MRRS support is
considered rare.
This must be done at device enablement stage because the MRRS setting may
get lost if PCI_COMMAND_MASTER on the parent bridge is cleared, and we are
only sure parent bridge is enabled at this point.
Fixes: 8b3517f88ff2 ("PCI: loongson: Prevent LS7A MRRS increases")
Closes: https://bugzilla.kernel.org/show_bug.cgi?id=217680
Link: https://bugs.debian.org/cgi-bin/bugreport.cgi?bug=1035587
Link: https://lore.kernel.org/r/20231201115028.84351-1-jiaxun.yang@flygoat.com
Signed-off-by: Jiaxun Yang <jiaxun.yang@flygoat.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Huacai Chen <chenhuacai@loongson.cn>
Cc: stable@vger.kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 83a939f0fdc208ff3639dd3d42ac9b3c35607fd2 upstream.
With CONFIG_PCI_EXYNOS=y and exynos_pcie_remove() marked with __exit, the
function is discarded from the driver. In this case a bound device can
still get unbound, e.g via sysfs. Then no cleanup code is run resulting in
resource leaks or worse.
The right thing to do is do always have the remove callback available.
This fixes the following warning by modpost:
WARNING: modpost: drivers/pci/controller/dwc/pci-exynos: section mismatch in reference: exynos_pcie_driver+0x8 (section: .data) -> exynos_pcie_remove (section: .exit.text)
(with ARCH=x86_64 W=1 allmodconfig).
Fixes: 340cba6092c2 ("pci: Add PCIe driver for Samsung Exynos")
Link: https://lore.kernel.org/r/20231001170254.2506508-2-u.kleine-koenig@pengutronix.de
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Alim Akhtar <alim.akhtar@samsung.com>
Cc: stable@vger.kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 3064ef2e88c1629c1e67a77d7bc20020b35846f2 upstream.
With CONFIG_PCIE_KIRIN=y and kirin_pcie_remove() marked with __exit, the
function is discarded from the driver. In this case a bound device can
still get unbound, e.g via sysfs. Then no cleanup code is run resulting in
resource leaks or worse.
The right thing to do is do always have the remove callback available.
This fixes the following warning by modpost:
drivers/pci/controller/dwc/pcie-kirin: section mismatch in reference: kirin_pcie_driver+0x8 (section: .data) -> kirin_pcie_remove (section: .exit.text)
(with ARCH=x86_64 W=1 allmodconfig).
Fixes: 000f60db784b ("PCI: kirin: Add support for a PHY layer")
Link: https://lore.kernel.org/r/20231001170254.2506508-3-u.kleine-koenig@pengutronix.de
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Cc: stable@vger.kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit a07d2497ed657eb2efeb967af47e22f573dcd1d6 upstream.
The DWC core driver exposes the write_dbi2() callback for writing to the
DBI2 registers in a vendor-specific way.
On the Qcom EP platforms, the DBI_CS2 bit in the ELBI region needs to be
asserted before writing to any DBI2 registers and deasserted once done.
So, let's implement the callback for the Qcom PCIe EP driver so that the
DBI2 writes are correctly handled in the hardware.
Without this callback, the DBI2 register writes like BAR size won't go
through and as a result, the default BAR size is set for all BARs.
[kwilczynski: commit log, renamed function to match the DWC convention]
Fixes: f55fee56a631 ("PCI: qcom-ep: Add Qualcomm PCIe Endpoint controller driver")
Suggested-by: Serge Semin <fancer.lancer@gmail.com>
Link: https://lore.kernel.org/linux-pci/20231025130029.74693-2-manivannan.sadhasivam@linaro.org
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Reviewed-by: Serge Semin <fancer.lancer@gmail.com>
Cc: stable@vger.kernel.org # 5.16+
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 7994db905c0fd692cf04c527585f08a91b560144 upstream.
The __init annotation makes the ks_pcie_probe() function disappear after
booting completes. However a device can also be bound later. In that case,
we try to call ks_pcie_probe(), but the backing memory is likely already
overwritten.
The right thing to do is do always have the probe callback available. Note
that the (wrong) __refdata annotation prevented this issue to be noticed by
modpost.
Fixes: 0c4ffcfe1fbc ("PCI: keystone: Add TI Keystone PCIe driver")
Link: https://lore.kernel.org/r/20231001170254.2506508-5-u.kleine-koenig@pengutronix.de
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Cc: stable@vger.kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 200bddbb3f5202bbce96444fdc416305de14f547 upstream.
With CONFIG_PCIE_KEYSTONE=y and ks_pcie_remove() marked with __exit, the
function is discarded from the driver. In this case a bound device can
still get unbound, e.g via sysfs. Then no cleanup code is run resulting in
resource leaks or worse.
The right thing to do is do always have the remove callback available.
Note that this driver cannot be compiled as a module, so ks_pcie_remove()
was always discarded before this change and modpost couldn't warn about
this issue. Furthermore the __ref annotation also prevents a warning.
Fixes: 0c4ffcfe1fbc ("PCI: keystone: Add TI Keystone PCIe driver")
Link: https://lore.kernel.org/r/20231001170254.2506508-4-u.kleine-koenig@pengutronix.de
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Cc: stable@vger.kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit 89db0793c9f2da265ecb6c1681f899d9af157f37 ]
Update dw_pcie_link_set_max_link_width() to set PCI_EXP_LNKCAP_MLW.
In accordance with the DW PCIe RC/EP HW manuals [1,2,3,...] aside with
the PORT_LINK_CTRL_OFF.LINK_CAPABLE and GEN2_CTRL_OFF.NUM_OF_LANES[8:0]
field there is another one which needs to be updated.
It's LINK_CAPABILITIES_REG.PCIE_CAP_MAX_LINK_WIDTH. If it isn't done at
the very least the maximum link-width capability CSR won't expose the
actual maximum capability.
[1] DesignWare Cores PCI Express Controller Databook - DWC PCIe Root Port,
Version 4.60a, March 2015, p.1032
[2] DesignWare Cores PCI Express Controller Databook - DWC PCIe Root Port,
Version 4.70a, March 2016, p.1065
[3] DesignWare Cores PCI Express Controller Databook - DWC PCIe Root Port,
Version 4.90a, March 2016, p.1057
...
[X] DesignWare Cores PCI Express Controller Databook - DWC PCIe Endpoint,
Version 5.40a, March 2019, p.1396
[X+1] DesignWare Cores PCI Express Controller Databook - DWC PCIe Root Port,
Version 5.40a, March 2019, p.1266
Suggested-by: Serge Semin <fancer.lancer@gmail.com>
Link: https://lore.kernel.org/linux-pci/20231018085631.1121289-4-yoshihiro.shimoda.uh@renesas.com
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Reviewed-by: Serge Semin <fancer.lancer@gmail.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit a9a1bcba90254975d4adbcca53f720318cf81c0c ]
This is a preparation before adding the Max-Link-width capability
setup which would in its turn complete the max-link-width setup
procedure defined by Synopsys in the HW-manual.
Seeing there is a max-link-speed setup method defined in the DW PCIe
core driver it would be good to have a similar function for the link
width setup.
That's why we need to define a dedicated function first from already
implemented but incomplete link-width setting up code.
Link: https://lore.kernel.org/linux-pci/20231018085631.1121289-3-yoshihiro.shimoda.uh@renesas.com
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Reviewed-by: Manivannan Sadhasivam <mani@kernel.org>
Reviewed-by: Serge Semin <fancer.lancer@gmail.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 408599ec561ad5862cda4f107626009f6fa97a74 ]
mvebu_pcie_setup_hw() setups the Maximum Link Width field in the Link
Capabilities registers using an open-coded variant of FIELD_PREP() with
a literal in shift. Improve readability by using
FIELD_PREP(PCI_EXP_LNKCAP_MLW, ...).
Link: https://lore.kernel.org/r/20230919125648.1920-6-ilpo.jarvinen@linux.intel.com
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 759574abd78e3b47ec45bbd31a64e8832cf73f97 ]
Use FIELD_GET() to extract PCIe Negotiated Link Width field instead of
custom masking and shifting.
Similarly, change custom code that misleadingly used
PCI_EXP_LNKSTA_NLW_SHIFT to prepare value for PCI_EXP_LNKCAP write
to use FIELD_PREP() with correct field define (PCI_EXP_LNKCAP_MLW).
Link: https://lore.kernel.org/r/20230919125648.1920-5-ilpo.jarvinen@linux.intel.com
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 5827e17d0555b566c32044b0632b46f9f95054fa ]
vmd_domain_reset() attempts to find whether the device may contain multiple
functions by checking 0x80 (Multi-Function Device), however, the hdr_type
variable has already been masked with PCI_HEADER_TYPE_MASK so the check can
never true.
To fix the issue, don't mask the read with PCI_HEADER_TYPE_MASK.
Fixes: 6aab5622296b ("PCI: vmd: Clean up domain before enumeration")
Link: https://lore.kernel.org/r/20231003125300.5541-2-ilpo.jarvinen@linux.intel.com
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Cc: Nirmal Patel <nirmal.patel@linux.intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
PARF_SLV_ADDR_SPACE_SIZE_2_3_3 is used by qcom_pcie_post_init_2_3_3().
This PCIe slave address space size register offset is 0x358 but was
incorrectly changed to 0x16c by 39171b33f652 ("PCI: qcom: Remove PCIE20_
prefix from register definitions").
This prevented access to slave address space registers like iATU, etc.,
so the IPQ8074 PCIe controller was not enumerated.
Revert back to the correct 0x358 offset and remove the unused
PARF_SLV_ADDR_SPACE_SIZE_2_3_3.
Fixes: 39171b33f652 ("PCI: qcom: Remove PCIE20_ prefix from register definitions")
Link: https://lore.kernel.org/r/20230919102948.1844909-1-quic_srichara@quicinc.com
Tested-by: Robert Marko <robimarko@gmail.com>
Signed-off-by: Sricharan Ramabadhran <quic_srichara@quicinc.com>
[bhelgaas: commit log]
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Manivannan Sadhasivam <mani@kernel.org>
Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Cc: stable@vger.kernel.org # v6.4+
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/pci/pci
Pull PCI updates from Bjorn Helgaas:
"Enumeration:
- Add locking to read/modify/write PCIe Capability Register accessors
for Link Control and Root Control
- Use pci_dev_id() when possible instead of manually composing ID
from dev->bus->number and dev->devfn
Resource management:
- Move prototypes for __weak sysfs resource files to linux/pci.h to
fix 'no previous prototype' warnings
- Make more I/O port accesses depend on HAS_IOPORT
- Use devm_platform_get_and_ioremap_resource() instead of open-coding
platform_get_resource() followed by devm_ioremap_resource()
Power management:
- Ensure devices are powered up while accessing VPD
- If device is powered-up, keep it that way while polling for PME
- Only read PCI_PM_CTRL register when available, to avoid reading the
wrong register and corrupting dev->current_state
Virtualization:
- Avoid Secondary Bus Reset on NVIDIA T4 GPUs
Error handling:
- Remove unused pci_disable_pcie_error_reporting()
- Unexport pci_enable_pcie_error_reporting(), used only by aer.c
- Unexport pcie_port_bus_type, used only by PCI core
VGA:
- Simplify and clean up typos in VGA arbiter
Apple PCIe controller driver:
- Initialize pcie->nvecs (number of available MSIs) before use
Broadcom iProc PCIe controller driver:
- Use of_property_read_bool() instead of low-level accessors for
boolean properties
Broadcom STB PCIe controller driver:
- Assert PERST# when probing BCM2711 because some bootloaders don't
do it
Freescale i.MX6 PCIe controller driver:
- Add .host_deinit() callback so we can clean up things like
regulators on probe failure or driver unload
Freescale Layerscape PCIe controller driver:
- Add support for link-down notification so the endpoint driver can
process LINK_DOWN events
- Add suspend/resume support, including manual
PME_Turn_off/PME_TO_Ack handshake
- Save Link Capabilities during probe so they can be restored when
handling a link-up event, since the controller loses the Link Width
and Link Speed values during reset
Intel VMD host bridge driver:
- Fix disable of bridge windows during domain reset; previously we
cleared the base/limit registers, which actually left the windows
enabled
Marvell MVEBU PCIe controller driver:
- Remove unused busn member
Microchip PolarFlare PCIe controller driver:
- Fix interrupt bit definitions so the SEC and DED interrupt handlers
work correctly
- Make driver buildable as a module
- Read FPGA MSI configuration parameters from hardware instead of
hard-coding them
Microsoft Hyper-V host bridge driver:
- To avoid a NULL pointer dereference, skip MSI restore after
hibernate if MSI/MSI-X hasn't been enabled
NVIDIA Tegra194 PCIe controller driver:
- Revert 'PCI: tegra194: Enable support for 256 Byte payload' because
Linux doesn't know how to reduce MPS from to 256 to 128 bytes for
endpoints below a switch (because other devices below the switch
might already be operating), which leads to 'Malformed TLP' errors
Qualcomm PCIe controller driver:
- Add DT and driver support for interconnect bandwidth voting for
'pcie-mem' and 'cpu-pcie' interconnects
- Fix broken SDX65 'compatible' DT property
- Configure controller so MHI bus master clock will be switched off
while in ASPM L1.x states
- Use alignment restriction from EPF core in EPF MHI driver
- Add Endpoint eDMA support
- Add MHI eDMA support
- Add Snapdragon SM8450 support to the EPF MHI driversupport
- Add MHI eDMA support
- Add Snapdragon SM8450 support to the EPF MHI driversupport
- Add MHI eDMA support
- Add Snapdragon SM8450 support to the EPF MHI driversupport
- Add MHI eDMA support
- Add Snapdragon SM8450 support to the EPF MHI driver
- Use iATU for EPF MHI transfers smaller than 4K to avoid eDMA setup
latency
- Add sa8775p DT binding and driver support
Rockchip PCIe controller driver:
- Use 64-bit mask on MSI 64-bit PCI address to avoid zeroing out the
upper 32 bits
SiFive FU740 PCIe controller driver:
- Set the supported number of MSI vectors so we can use all available
MSI interrupts
Synopsys DesignWare PCIe controller driver:
- Add generic dwc suspend/resume APIs (dw_pcie_suspend_noirq() and
dw_pcie_resume_noirq()) to be called by controller driver
suspend/resume ops, and a controller callback to send PME_Turn_Off
MicroSemi Switchtec management driver:
- Add support for PCIe Gen5 devices
Miscellaneous:
- Reorder and compress to reduce size of struct pci_dev
- Fix race in DOE destroy_work_on_stack()
- Add stubs to avoid casts between incompatible function types
- Explicitly include correct DT includes to untangle headers"
* tag 'pci-v6.6-changes' of git://git.kernel.org/pub/scm/linux/kernel/git/pci/pci: (96 commits)
PCI: qcom-ep: Add ICC bandwidth voting support
dt-bindings: PCI: qcom: ep: Add interconnects path
PCI: qcom-ep: Treat unknown IRQ events as an error
dt-bindings: PCI: qcom: Fix SDX65 compatible
PCI: endpoint: Add kernel-doc for pci_epc_mem_init() API
PCI: epf-mhi: Use iATU for small transfers
PCI: epf-mhi: Add support for SM8450
PCI: epf-mhi: Add eDMA support
PCI: qcom-ep: Add eDMA support
PCI: epf-mhi: Make use of the alignment restriction from EPF core
PCI/PM: Only read PCI_PM_CTRL register when available
PCI: qcom: Add support for sa8775p SoC
dt-bindings: PCI: qcom: Add sa8775p compatible
PCI: qcom-ep: Pass alignment restriction to the EPF core
PCI: Simplify pcie_capability_clear_and_set_word() control flow
PCI: Tidy config space save/restore messages
PCI: Fix code formatting inconsistencies
PCI: Fix typos in docs and comments
PCI: Fix pci_bus_resetable(), pci_slot_resetable() name typos
PCI: Simplify pci_dev_driver()
...
|
|
- Reorder struct pci_dev to avoid holes and reduce size (Christophe
JAILLET)
- Change pdev->rom_attr_enabled to single bit since it's only a boolean
value (Christophe JAILLET)
- Use struct_size() in pirq_convert_irt_table() instead of hand-writing it
(Christophe JAILLET)
- Explicitly include correct DT includes to untangle headers (Rob Herring)
- Fix a DOE race between destroy_work_on_stack() and the stack-allocated
task->work struct going out of scope in pci_doe() (Ira Weiny)
- Use pci_dev_id() when possible instead of manually composing ID from
dev->bus->number and dev->devfn (Xiongfeng Wang, Zheng Zengkai)
- Move pci_create_resource_files() declarations to linux/pci.h for alpha
build warnings (Arnd Bergmann)
- Remove unused hotplug function declarations (Yue Haibing)
- Remove unused mvebu struct mvebu_pcie.busn (Pali Rohár)
- Unexport pcie_port_bus_type (Bjorn Helgaas)
- Remove unnecessary sysfs ID local variable initialization (Bjorn Helgaas)
- Fix BAR value printk formatting to accommodate 32-bit values (Bjorn
Helgaas)
- Use consistent pointer types for config access syscall get_user() and
put_user() uses (Bjorn Helgaas)
- Simplify AER_RECOVER_RING_SIZE definition (Bjorn Helgaas)
- Simplify pci_pio_to_address() (Bjorn Helgaas)
- Simplify pci_dev_driver() (Bjorn Helgaas)
- Fix pci_bus_resetable(), pci_slot_resetable() name typos (Bjorn Helgaas)
- Fix code and doc typos and code formatting (Bjorn Helgaas)
- Tidy config space save/restore messages (Bjorn Helgaas)
* pci/misc:
PCI: Tidy config space save/restore messages
PCI: Fix code formatting inconsistencies
PCI: Fix typos in docs and comments
PCI: Fix pci_bus_resetable(), pci_slot_resetable() name typos
PCI: Simplify pci_dev_driver()
PCI: Simplify pci_pio_to_address()
PCI/AER: Simplify AER_RECOVER_RING_SIZE definition
PCI: Use consistent put_user() pointer types
PCI: Fix printk field formatting
PCI: Remove unnecessary initializations
PCI: Unexport pcie_port_bus_type
PCI: mvebu: Remove unused busn member
PCI: Remove unused function declarations
PCI/sysfs: Move declarations to linux/pci.h
PCI/P2PDMA: Use pci_dev_id() to simplify the code
PCI/IOV: Use pci_dev_id() to simplify the code
PCI/AER: Use pci_dev_id() to simplify the code
PCI: apple: Use pci_dev_id() to simplify the code
PCI/DOE: Fix destroy_work_on_stack() race
PCI: Explicitly include correct DT includes
x86/PCI: Use struct_size() in pirq_convert_irt_table()
PCI: Change pdev->rom_attr_enabled to single bit
PCI: Reorder pci_dev fields to reduce holes
|
|
- Use Use devm_platform_get_and_ioremap_resource() instead of open-coding
platform_get_resource() followed by devm_ioremap_resource() (Yang Li)
* pci/controller/resources:
PCI: imx6: Use devm_platform_get_and_ioremap_resource()
PCI: xgene-msi: Use devm_platform_get_and_ioremap_resource()
PCI: v3: Use devm_platform_get_and_ioremap_resource()
PCI: rcar-gen2: Use devm_platform_get_and_ioremap_resource()
|
|
- Add stubs for devm action functions that call clk_disable_unprepare() to
avoid casts between incompatible function types (Krzysztof Wilczyński)
* pci/controller/remove-void-cast:
PCI: microchip: Remove cast between incompatible function type
PCI: keembay: Remove cast between incompatible function type
PCI: meson: Remove cast between incompatible function type
|
|
- Fix disable of bridge windows during domain reset; previously we cleared
the base/limit registers, which left the windows enabled (Nirmal Patel)
* pci/controller/vmd:
PCI: vmd: Disable bridge window for domain reset
|
|
- Revert "PCI: tegra194: Enable support for 256 Byte payload" because Linux
doesn't know how to reduce MPS from to 256 to 128 bytes for Endpoints
below a Switch (because other devices below the Switch might already be
operating), which leads to Malformed TLP errors (Vidya Sagar)
* pci/controller/tegra194:
Revert "PCI: tegra194: Enable support for 256 Byte payload"
|
|
- Use 64-bit mask on MSI 64-bit PCI address to avoid zeroing out the upper
32 bits (Rick Wertenbroek)
* pci/controller/rockchip:
PCI: rockchip: Use 64-bit mask on MSI 64-bit PCI address
|
|
- Log unknown Qcom Endpoint IRQ events at error level, not debug level
(Manivannan Sadhasivam)
- Add DT and driver support for qcom interconnect bandwidth voting for
"pcie-mem" and "cpu-pcie" interconnects (Krishna chaitanya chundru)
* pci/controller/qcom-ep:
PCI: qcom-ep: Add ICC bandwidth voting support
dt-bindings: PCI: qcom: ep: Add interconnects path
PCI: qcom-ep: Treat unknown IRQ events as an error
|
|
- Pass the Qcom Endpoint 4K alignment requirement for outbound windows to
the EPF core so EPF drivers can use it (Manivannan Sadhasivam)
- Use alignment restriction from EPF core in Qcom EPF MHI driver
(Manivannan Sadhasivam)
- Add Qcom Endpoint eDMA support by enabling the eDMA IRQ (Manivannan
Sadhasivam)
- Add Qcom MHI eDMA support (Manivannan Sadhasivam)
- Add Qcom Snapdragon SM8450 support to the EPF MHI driver (Manivannan
Sadhasivam)
- Use iATU for EPF MHI transfers smaller than 4K to avoid eDMA setup
latency (Manivannan Sadhasivam)
- Add pci_epc_mem_init() kernel-doc (Manivannan Sadhasivam)
* pci/controller/qcom-edma:
PCI: endpoint: Add kernel-doc for pci_epc_mem_init() API
PCI: epf-mhi: Use iATU for small transfers
PCI: epf-mhi: Add support for SM8450
PCI: epf-mhi: Add eDMA support
PCI: qcom-ep: Add eDMA support
PCI: epf-mhi: Make use of the alignment restriction from EPF core
PCI: qcom-ep: Pass alignment restriction to the EPF core
|
|
- Configure controller so MHI bus master clock will be switched off while
in ASPM L1.x states (Manivannan Sadhasivam)
- Add sa8775p DT binding and driver support (Mrinmay Sarkar)
- Fix broken DT SDX65 "compatible" property (Krzysztof Kozlowski)
* pci/controller/qcom:
dt-bindings: PCI: qcom: Fix SDX65 compatible
PCI: qcom: Add support for sa8775p SoC
dt-bindings: PCI: qcom: Add sa8775p compatible
PCI: qcom-ep: Switch MHI bus master clock off during L1SS
|
|
- Fix DED and SEC interrupt bit offsets so interrupt handlers work
correctly (Daire McNamara)
- Make driver buildable as a module (Daire McNamara)
- Reorganize register #defines to align with hardware docs (Daire McNamara)
- Tweak register accessors to simplify callers (Daire McNamara)
- Refactor interrupt initialisation (Daire McNamara)
- Read FPGA MSI configuration parameters from hardware instead of
hard-coding them (Daire McNamara)
- Re-partition code between probe() and init() (Daire McNamara)
* pci/controller/microchip:
PCI: microchip: Re-partition code between probe() and init()
PCI: microchip: Gather MSI information from hardware config registers
PCI: microchip: Clean up initialisation of interrupts
PCI: microchip: Enable event handlers to access bridge and control pointers
PCI: microchip: Align register, offset, and mask names with HW docs
PCI: microchip: Enable building driver as a module
PCI: microchip: Correct the DED and SEC interrupt bit offsets
|
|
- Add support for link-down notification so the endpoint driver can process
LINK_DOWN events (Frank Li)
- Save Link Capabilities during probe so they can be restored when handling
a link-up event, since the controller loses the Link Width and Link Speed
values during reset (Xiaowei Bao)
* pci/controller/layerscape:
PCI: layerscape: Add workaround for lost link capabilities during reset
PCI: layerscape: Add support for link-down notification
|
|
- Use of_property_read_bool() instead of low-level accessors for boolean
properties (Rob Herring)
* pci/controller/iproc:
PCI: iproc: Use of_property_read_bool() for boolean properties
|
|
- To avoid a NULL pointer dereference, skip MSI restore after hibernate if
MSI/MSI-X hasn't been enabled (Dexuan Cui)
* pci/controller/hv:
PCI: hv: Fix a crash in hv_pci_restore_msi_msg() during hibernation
|
