| Age | Commit message (Collapse) | Author |
|---|
|
ASPM is supported by Qcom host controllers/bridges on most of the recent
platforms and so the devices tested so far. But for enabling ASPM by
default (without using Kconfig, kernel command-line or sysfs), BIOS has
to enable ASPM on both host bridge and downstream devices during boot.
Unfortunately, none of the BIOS available on Qcom platforms enables
ASPM. Due to this, the platforms making use of Qcom SoCs draw high power
during runtime.
To fix this power draw issue, users have to enable ASPM using Kconfig,
kernel command-line, sysfs or the BIOS has to start enabling ASPM.
The latter may happen in the future, but that won't address the issue on
current platforms. Also, asking users to enable a feature to get the power
management right would provide an unpleasant out-of-the-box experience.
So the apt solution is to enable ASPM in the controller driver itself. And
this is being accomplished by calling pci_enable_link_state() in the newly
introduced host_post_init() callback for all the devices connected to the
bus. This function enables all supported link low power states for both
host bridge and the downstream devices.
Due to limited testing, ASPM is only enabled for platforms making use of
ops_1_9_0 callbacks.
[kwilczynski: commit log]
Link: https://lore.kernel.org/linux-pci/20231010155914.9516-3-manivannan.sadhasivam@linaro.org
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
|
|
- Reorder struct pci_dev to avoid holes and reduce size (Christophe
JAILLET)
- Change pdev->rom_attr_enabled to single bit since it's only a boolean
value (Christophe JAILLET)
- Use struct_size() in pirq_convert_irt_table() instead of hand-writing it
(Christophe JAILLET)
- Explicitly include correct DT includes to untangle headers (Rob Herring)
- Fix a DOE race between destroy_work_on_stack() and the stack-allocated
task->work struct going out of scope in pci_doe() (Ira Weiny)
- Use pci_dev_id() when possible instead of manually composing ID from
dev->bus->number and dev->devfn (Xiongfeng Wang, Zheng Zengkai)
- Move pci_create_resource_files() declarations to linux/pci.h for alpha
build warnings (Arnd Bergmann)
- Remove unused hotplug function declarations (Yue Haibing)
- Remove unused mvebu struct mvebu_pcie.busn (Pali Rohár)
- Unexport pcie_port_bus_type (Bjorn Helgaas)
- Remove unnecessary sysfs ID local variable initialization (Bjorn Helgaas)
- Fix BAR value printk formatting to accommodate 32-bit values (Bjorn
Helgaas)
- Use consistent pointer types for config access syscall get_user() and
put_user() uses (Bjorn Helgaas)
- Simplify AER_RECOVER_RING_SIZE definition (Bjorn Helgaas)
- Simplify pci_pio_to_address() (Bjorn Helgaas)
- Simplify pci_dev_driver() (Bjorn Helgaas)
- Fix pci_bus_resetable(), pci_slot_resetable() name typos (Bjorn Helgaas)
- Fix code and doc typos and code formatting (Bjorn Helgaas)
- Tidy config space save/restore messages (Bjorn Helgaas)
* pci/misc:
PCI: Tidy config space save/restore messages
PCI: Fix code formatting inconsistencies
PCI: Fix typos in docs and comments
PCI: Fix pci_bus_resetable(), pci_slot_resetable() name typos
PCI: Simplify pci_dev_driver()
PCI: Simplify pci_pio_to_address()
PCI/AER: Simplify AER_RECOVER_RING_SIZE definition
PCI: Use consistent put_user() pointer types
PCI: Fix printk field formatting
PCI: Remove unnecessary initializations
PCI: Unexport pcie_port_bus_type
PCI: mvebu: Remove unused busn member
PCI: Remove unused function declarations
PCI/sysfs: Move declarations to linux/pci.h
PCI/P2PDMA: Use pci_dev_id() to simplify the code
PCI/IOV: Use pci_dev_id() to simplify the code
PCI/AER: Use pci_dev_id() to simplify the code
PCI: apple: Use pci_dev_id() to simplify the code
PCI/DOE: Fix destroy_work_on_stack() race
PCI: Explicitly include correct DT includes
x86/PCI: Use struct_size() in pirq_convert_irt_table()
PCI: Change pdev->rom_attr_enabled to single bit
PCI: Reorder pci_dev fields to reduce holes
|
|
Add support for sa8775p SoC that uses controller version 5.90
reusing the 1.9.0 config.
Link: https://lore.kernel.org/linux-pci/1689960276-29266-3-git-send-email-quic_msarkar@quicinc.com
Signed-off-by: Mrinmay Sarkar <quic_msarkar@quicinc.com>
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Reviewed-by: Bjorn Andersson <andersson@kernel.org>
Reviewed-by: Manivannan Sadhasivam <mani@kernel.org>
|
|
The DT of_device.h and of_platform.h date back to the separate
of_platform_bus_type before it as merged into the regular platform bus. As
part of that merge prepping Arm DT support 13 years ago, they "temporarily"
include each other. They also include platform_device.h and of.h. As a
result, there's a pretty much random mix of those include files used
throughout the tree. In order to detangle these headers and replace the
implicit includes with struct declarations, users need to explicitly
include the correct includes.
Link: https://lore.kernel.org/r/20230714174827.4061572-1-robh@kernel.org
Signed-off-by: Rob Herring <robh@kernel.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
|
|
SoCs making use of Qcom PCIe controller IP v2.1.0 do not support hotplug
functionality. But the hotplug capability bit is set by default in the
hardware. This causes the kernel PCI core to register hotplug service for
the controller and send hotplug commands to it. But those commands will
timeout generating messages as below during boot and suspend/resume.
[ 5.782159] pcieport 0001:00:00.0: pciehp: Timeout on hotplug command 0x03c0 (issued 2020 msec ago)
[ 5.810161] pcieport 0001:00:00.0: pciehp: Timeout on hotplug command 0x03c0 (issued 2048 msec ago)
[ 7.838162] pcieport 0001:00:00.0: pciehp: Timeout on hotplug command 0x07c0 (issued 2020 msec ago)
[ 7.870159] pcieport 0001:00:00.0: pciehp: Timeout on hotplug command 0x07c0 (issued 2052 msec ago)
This not only spams the console output but also induces a delay of a
couple of seconds. To fix this issue, let's clear the HPC bit in
PCI_EXP_SLTCAP register as a part of the post init sequence to not
advertise the hotplug capability for the controller.
Link: https://lore.kernel.org/r/20230619150408.8468-10-manivannan.sadhasivam@linaro.org
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Lorenzo Pieralisi <lpieralisi@kernel.org>
|
|
SoCs making use of Qcom PCIe controller IP v1.0.0 do not support hotplug
functionality. But the hotplug capability bit is set by default in the
hardware. This causes the kernel PCI core to register hotplug service for
the controller and send hotplug commands to it. But those commands will
timeout generating messages as below during boot and suspend/resume.
[ 5.782159] pcieport 0001:00:00.0: pciehp: Timeout on hotplug command 0x03c0 (issued 2020 msec ago)
[ 5.810161] pcieport 0001:00:00.0: pciehp: Timeout on hotplug command 0x03c0 (issued 2048 msec ago)
[ 7.838162] pcieport 0001:00:00.0: pciehp: Timeout on hotplug command 0x07c0 (issued 2020 msec ago)
[ 7.870159] pcieport 0001:00:00.0: pciehp: Timeout on hotplug command 0x07c0 (issued 2052 msec ago)
This not only spams the console output but also induces a delay of a
couple of seconds. To fix this issue, let's clear the HPC bit in
PCI_EXP_SLTCAP register as a part of the post init sequence to not
advertise the hotplug capability for the controller.
Link: https://lore.kernel.org/r/20230619150408.8468-9-manivannan.sadhasivam@linaro.org
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Lorenzo Pieralisi <lpieralisi@kernel.org>
|
|
The post init sequence of IP v2.4.0 is same as v2.3.2. So let's reuse the
v2.3.2 sequence which now also disables hotplug capability of the
controller as it is not at all supported on any SoCs making use of this IP.
Link: https://lore.kernel.org/r/20230619150408.8468-8-manivannan.sadhasivam@linaro.org
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Lorenzo Pieralisi <lpieralisi@kernel.org>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
|
|
SoCs making use of Qcom PCIe controller IP v2.3.2 do not support hotplug
functionality. But the hotplug capability bit is set by default in the
hardware. This causes the kernel PCI core to register hotplug service for
the controller and send hotplug commands to it. But those commands will
timeout generating messages as below during boot and suspend/resume.
[ 5.782159] pcieport 0001:00:00.0: pciehp: Timeout on hotplug command 0x03c0 (issued 2020 msec ago)
[ 5.810161] pcieport 0001:00:00.0: pciehp: Timeout on hotplug command 0x03c0 (issued 2048 msec ago)
[ 7.838162] pcieport 0001:00:00.0: pciehp: Timeout on hotplug command 0x07c0 (issued 2020 msec ago)
[ 7.870159] pcieport 0001:00:00.0: pciehp: Timeout on hotplug command 0x07c0 (issued 2052 msec ago)
This not only spams the console output but also induces a delay of a
couple of seconds. To fix this issue, let's clear the HPC bit in
PCI_EXP_SLTCAP register as a part of the post init sequence to not
advertise the hotplug capability for the controller.
Link: https://lore.kernel.org/r/20230619150408.8468-7-manivannan.sadhasivam@linaro.org
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Lorenzo Pieralisi <lpieralisi@kernel.org>
|
|
SoCs making use of Qcom PCIe controller IPs v2.3.3 and v2.9.0 do not
support hotplug functionality. But the hotplug capability bit is set by
default in the hardware. This causes the kernel PCI core to register
hotplug service for the controller and send hotplug commands to it. But
those commands will timeout generating messages as below during boot
and suspend/resume.
[ 5.782159] pcieport 0001:00:00.0: pciehp: Timeout on hotplug command 0x03c0 (issued 2020 msec ago)
[ 5.810161] pcieport 0001:00:00.0: pciehp: Timeout on hotplug command 0x03c0 (issued 2048 msec ago)
[ 7.838162] pcieport 0001:00:00.0: pciehp: Timeout on hotplug command 0x07c0 (issued 2020 msec ago)
[ 7.870159] pcieport 0001:00:00.0: pciehp: Timeout on hotplug command 0x07c0 (issued 2052 msec ago)
This not only spams the console output but also induces a delay of a
couple of seconds. To fix this issue, let's not set the HPC bit in
PCI_EXP_SLTCAP register as a part of the post init sequence to not
advertise the hotplug capability for the controller.
Link: https://lore.kernel.org/r/20230619150408.8468-6-manivannan.sadhasivam@linaro.org
Tested-by: Sricharan Ramabadhran <quic_srichara@quicinc.com>
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Lorenzo Pieralisi <lpieralisi@kernel.org>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
|
|
SoCs making use of Qcom PCIe controller IPs v2.7.0 and v1.9.0 do not
support hotplug functionality. But the hotplug capability bit is set by
default in the hardware. This causes the kernel PCI core to register
hotplug service for the controller and send hotplug commands to it. But
those commands will timeout generating messages as below during boot and
suspend/resume.
[ 5.782159] pcieport 0001:00:00.0: pciehp: Timeout on hotplug command 0x03c0 (issued 2020 msec ago)
[ 5.810161] pcieport 0001:00:00.0: pciehp: Timeout on hotplug command 0x03c0 (issued 2048 msec ago)
[ 7.838162] pcieport 0001:00:00.0: pciehp: Timeout on hotplug command 0x07c0 (issued 2020 msec ago)
[ 7.870159] pcieport 0001:00:00.0: pciehp: Timeout on hotplug command 0x07c0 (issued 2052 msec ago)
This not only spams the console output but also induces a delay of a
couple of seconds. To fix this issue, let's clear the HPC bit in
PCI_EXP_SLTCAP register as a part of the post init sequence to not
advertise the hotplug capability for the controller.
Link: https://lore.kernel.org/r/20230619150408.8468-5-manivannan.sadhasivam@linaro.org
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Lorenzo Pieralisi <lpieralisi@kernel.org>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
|
|
In the post init sequence of v2.9.0, write access to read only registers
are not disabled after updating the registers. Fix it by disabling the
access after register update.
While at it, let's also add a newline after existing dw_pcie_dbi_ro_wr_en()
guard function to align with rest of the driver.
Link: https://lore.kernel.org/r/20230619150408.8468-4-manivannan.sadhasivam@linaro.org
Fixes: 0cf7c2efe8ac ("PCI: qcom: Add IPQ60xx support")
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Lorenzo Pieralisi <lpieralisi@kernel.org>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
|
|
DWC core already exposes dw_pcie_dbi_ro_wr_{en/dis} helper APIs for
enabling and disabling the write access to read only DBI registers. So
let's use them instead of doing it manually.
Also, the existing code doesn't disable the write access when it's done.
This is also fixed now.
Link: https://lore.kernel.org/r/20230619150408.8468-3-manivannan.sadhasivam@linaro.org
Fixes: 5d76117f070d ("PCI: qcom: Add support for IPQ8074 PCIe controller")
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Lorenzo Pieralisi <lpieralisi@kernel.org>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
|
|
In the post init sequence of v2.9.0, write access to read only registers
are not disabled after updating the registers. Fix it by disabling the
access after register update.
Link: https://lore.kernel.org/r/20230619150408.8468-2-manivannan.sadhasivam@linaro.org
Fixes: 5d76117f070d ("PCI: qcom: Add support for IPQ8074 PCIe controller")
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Lorenzo Pieralisi <lpieralisi@kernel.org>
Cc: <stable@vger.kernel.org>
|
|
SM8550 requires two additional clocks for proper working.
Add these two clocks as optional clocks (as only required by this
platform) and compatible for this platform.
While at it, let's also rename the reset variable to "rst" from
"pci_reset" to match the existing naming preference.
Link: https://lore.kernel.org/r/20230320144658.1794991-2-abel.vesa@linaro.org
Signed-off-by: Abel Vesa <abel.vesa@linaro.org>
[lpieralisi@kernel.org: commit log rewording]
Signed-off-by: Lorenzo Pieralisi <lpieralisi@kernel.org>
Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Reviewed-by: Manivannan Sadhasivam <mani@kernel.org>
Reviewed-by: Johan Hovold <johan+linaro@kernel.org>
|
|
Add support for SDX55 SoC reusing the 1.9.0 config. The PCIe controller is
of version 1.10.0 but it is compatible with the 1.9.0 config. This SoC also
requires "sleep" clock which is added as an optional clock in the driver,
since it is not required on other SoCs.
Link: https://lore.kernel.org/r/20230308082424.140224-14-manivannan.sadhasivam@linaro.org
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Lorenzo Pieralisi <lpieralisi@kernel.org>
|
|
Qcom PCIe RC driver waits for the PHY link to be up during the probe;
this consumes several milliseconds during boot.
Enable async probe by default so that other drivers can load in parallel
while this driver waits for the link to be up.
Suggested-by: Rob Herring <robh@kernel.org>
Link: https://lore.kernel.org/r/20230320064644.5217-1-manivannan.sadhasivam@linaro.org
Tested-by: Johan Hovold <johan+linaro@kernel.org>
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Lorenzo Pieralisi <lpieralisi@kernel.org>
Reviewed-by: Johan Hovold <johan+linaro@kernel.org>
|
|
During the system suspend, vote for minimal interconnect bandwidth (1KiB)
to keep the interconnect path active for config access and also turn OFF
the resources like clock and PHY if there are no active devices connected
to the controller. For the controllers with active devices, the resources
are kept ON as removing the resources will trigger access violation during
the late end of suspend cycle as kernel tries to access the config space of
PCIe devices to mask the MSIs.
Also, it is not desirable to put the link into L2/L3 state as that
implies VDD supply will be removed and the devices may go into powerdown
state. This will affect the lifetime of storage devices like NVMe.
And finally, during resume, turn ON the resources if the controller was
truly suspended (resources OFF) and update the interconnect bandwidth
based on PCIe Gen speed.
Suggested-by: Krishna chaitanya chundru <quic_krichai@quicinc.com>
Link: https://lore.kernel.org/r/20230403154922.20704-2-manivannan.sadhasivam@linaro.org
Tested-by: Johan Hovold <johan+linaro@kernel.org>
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Lorenzo Pieralisi <lpieralisi@kernel.org>
Reviewed-by: Johan Hovold <johan+linaro@kernel.org>
Acked-by: Dhruva Gole <d-gole@ti.com>
|
|
Qualcomm PCIe controllers have debug registers in the MHI region that
count PCIe link transitions. Expose them over debugfs to userspace to
help debug the low power issues.
Note that even though the registers are prefixed as PARF_, they don't
live under the "parf" register region. The register naming is following
the Qualcomm's internal documentation as like other registers.
While at it, let's arrange the local variables in probe function to follow
reverse XMAS tree order.
Link: https://lore.kernel.org/r/20230316081117.14288-20-manivannan.sadhasivam@linaro.org
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Lorenzo Pieralisi <lpieralisi@kernel.org>
|
|
qcom_pcie_config_sid_sm8250() function no longer applies only to SM8250.
So let's rename it to reflect the actual IP version and also move its
definition to keep it sorted as per IP revisions.
Link: https://lore.kernel.org/r/20230316081117.14288-15-manivannan.sadhasivam@linaro.org
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Lorenzo Pieralisi <lpieralisi@kernel.org>
|
|
To keep uniformity, let's use macros to define the total number of clocks
and supplies in qcom_pcie_resources_{2_7_0/2_9_0} structs.
Link: https://lore.kernel.org/r/20230316081117.14288-14-manivannan.sadhasivam@linaro.org
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Lorenzo Pieralisi <lpieralisi@kernel.org>
|
|
All the resets are asserted and deasserted at the same time. So the bulk
reset APIs can be used to handle them together. This simplifies the code
a lot.
It should be noted that there were delays in-between the reset asserts and
deasserts. But going by the config used by other revisions, those delays
are not really necessary. So a single delay after all asserts and one after
deasserts is used.
The total number of resets supported is 12 but only ipq4019 is using all of
them.
Link: https://lore.kernel.org/r/20230316081117.14288-13-manivannan.sadhasivam@linaro.org
Tested-by: Sricharan Ramabadhran <quic_srichara@quicinc.com>
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Lorenzo Pieralisi <lpieralisi@kernel.org>
|
|
All the resets are asserted and deasserted at the same time. So the bulk
reset APIs can be used to handle them together. This simplifies the code
a lot.
Link: https://lore.kernel.org/r/20230316081117.14288-12-manivannan.sadhasivam@linaro.org
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Lorenzo Pieralisi <lpieralisi@kernel.org>
|
|
All the clocks are enabled and disabled at the same time. So the bulk clock
APIs can be used to handle them together. This simplifies the code a lot.
Link: https://lore.kernel.org/r/20230316081117.14288-11-manivannan.sadhasivam@linaro.org
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Lorenzo Pieralisi <lpieralisi@kernel.org>
|
|
All the clocks are enabled and disabled at the same time. So the bulk clock
APIs can be used to handle them together. This simplifies the code a lot.
Link: https://lore.kernel.org/r/20230316081117.14288-10-manivannan.sadhasivam@linaro.org
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Lorenzo Pieralisi <lpieralisi@kernel.org>
|
|
All the clocks are enabled and disabled at the same time. So the bulk clock
APIs can be used to handle them together. This simplifies the code a lot.
Link: https://lore.kernel.org/r/20230316081117.14288-9-manivannan.sadhasivam@linaro.org
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Lorenzo Pieralisi <lpieralisi@kernel.org>
|
|
All the resets are asserted and deasserted at the same time. So the bulk
reset APIs can be used to handle them together. This simplifies the code
a lot.
While at it, let's also move the qcom_pcie_resources_2_1_0 struct below
qcom_pcie_resources_1_0_0 to keep it sorted.
Link: https://lore.kernel.org/r/20230316081117.14288-8-manivannan.sadhasivam@linaro.org
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Lorenzo Pieralisi <lpieralisi@kernel.org>
|
|
To maintain uniformity, let's use lower case for representing hexadecimal
numbers.
Link: https://lore.kernel.org/r/20230316081117.14288-7-manivannan.sadhasivam@linaro.org
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Lorenzo Pieralisi <lpieralisi@kernel.org>
|
|
Some of the registers are changed using hardcoded bitfields without macros.
This provides no information on what the register setting is about. So add
the macros to those fields for making the code more understandable.
Link: https://lore.kernel.org/r/20230316081117.14288-6-manivannan.sadhasivam@linaro.org
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Lorenzo Pieralisi <lpieralisi@kernel.org>
|
|
To maintain uniformity throughout the driver and also to make the code
easier to read, let's make use of bitfield definitions for register fields.
Link: https://lore.kernel.org/r/20230316081117.14288-5-manivannan.sadhasivam@linaro.org
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Lorenzo Pieralisi <lpieralisi@kernel.org>
|
|
Sorting the registers and their bit definitions will make it easier to add
more definitions in the future and it also helps in maintenance.
While at it, let's also group the registers and bit definitions separately
as done in the pcie-qcom-ep driver.
Link: https://lore.kernel.org/r/20230316081117.14288-4-manivannan.sadhasivam@linaro.org
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Lorenzo Pieralisi <lpieralisi@kernel.org>
|
|
The PCIE part is redundant and 20 doesn't represent anything across the
SoCs supported now. So let's get rid of the prefix.
This involves adding the IP version suffix to one definition of
PARF_SLV_ADDR_SPACE_SIZE that defines offset specific to that version.
The other definition is generic for the rest of the versions.
Also, the register PCIE20_LNK_CONTROL2_LINK_STATUS2 is not used anywhere,
hence removed.
Link: https://lore.kernel.org/r/20230316081117.14288-3-manivannan.sadhasivam@linaro.org
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Lorenzo Pieralisi <lpieralisi@kernel.org>
|
|
Qcom PCIe IP version v2.7.0 and its derivatives don't contain the
PCIE20_PARF_AXI_MSTR_WR_ADDR_HALT register. Instead, they have the new
PCIE20_PARF_AXI_MSTR_WR_ADDR_HALT_V2 register. So fix the incorrect
register usage which is modifying a different register.
Also in this IP version, this register change doesn't depend on MSI
being enabled. So remove that check also.
Link: https://lore.kernel.org/r/20230316081117.14288-2-manivannan.sadhasivam@linaro.org
Fixes: ed8cc3b1fc84 ("PCI: qcom: Add support for SDM845 PCIe controller")
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Lorenzo Pieralisi <lpieralisi@kernel.org>
Cc: <stable@vger.kernel.org> # 5.6+
|
|
IPQ8074 has one Gen2 and one Gen3 port, with Gen2 port already supported.
Add compatible for Gen3 port which uses the same controller as IPQ6018.
Link: https://lore.kernel.org/r/20230113164449.906002-7-robimarko@gmail.com
Signed-off-by: Robert Marko <robimarko@gmail.com>
Signed-off-by: Lorenzo Pieralisi <lpieralisi@kernel.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
|
|
Implement the new host_deinit() callback so that the PHY is powered off
and regulators and clocks are disabled also on late host-init errors.
Link: https://lore.kernel.org/r/20221017114705.8277-2-johan+linaro@kernel.org
Fixes: 82a823833f4e ("PCI: qcom: Add Qualcomm PCIe controller driver")
Signed-off-by: Johan Hovold <johan+linaro@kernel.org>
Signed-off-by: Lorenzo Pieralisi <lpieralisi@kernel.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Manivannan Sadhasivam <mani@kernel.org>
|
|
Add support for the PCIe host on Qualcomm SM8350 platform.
Link: https://lore.kernel.org/r/20221118233242.2904088-4-dmitry.baryshkov@linaro.org
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Signed-off-by: Lorenzo Pieralisi <lpieralisi@kernel.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Bjorn Andersson <andersson@kernel.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/phy/linux-phy
Pull phy updates from Vinod Koul:
"This tme we have again a big pile of qcom-qmp-* changes, one new
driver and bunch of new hardware support.
New hardware support:
- Allwinner H616 USB PHY and A100 DPHY support
- TI J721s2, J784s4 and J721e support
- Freescale i.MX8MP PCIe PHY support
- New driver for Renesas Ethernet SERDES supporting R-Car S4-8
- Qualcomm SM8450 PCIe1 PHY support in EP mode
- Qualcomm SC8280XP PCIe PHY support (including x4 mode)
- Fixed Qualcomm SC8280XP USB4-USB3-DP PHY DT bindings
Updates:
- A big pile of updates on qcom-qmp-* drivers following the driver
split and reorganization merged earlier
- Phy order of API calls documentation update"
* tag 'phy-for-6.2' of git://git.kernel.org/pub/scm/linux/kernel/git/phy/linux-phy: (174 commits)
phy: ti: phy-j721e-wiz: add j721s2-wiz-10g module support
dt-bindings: phy-j721e-wiz: add j721s2 compatible string
phy: use devm_platform_get_and_ioremap_resource()
phy: allwinner: phy-sun6i-mipi-dphy: Add the A100 DPHY variant
phy: allwinner: phy-sun6i-mipi-dphy: Add a variant power-on hook
phy: allwinner: phy-sun6i-mipi-dphy: Set the enable bit last
phy: allwinner: phy-sun6i-mipi-dphy: Make RX support optional
dt-bindings: sun6i-a31-mipi-dphy: Add the A100 DPHY variant
dt-bindings: sun6i-a31-mipi-dphy: Add the interrupts property
phy: qcom-qmp-pcie: drop redundant clock allocation
phy: qcom-qmp-usb: drop redundant clock allocation
phy: qcom-qmp: drop unused type header
phy: qcom-qmp-usb: drop sc8280xp reference-clock source
dt-bindings: phy: qcom,sc8280xp-qmp-usb3-uni: drop reference-clock source
phy: qcom-qmp-combo: add support for updated sc8280xp binding
phy: qcom-qmp-combo: rename DP_PHY register pointer
phy: qcom-qmp-combo: rename common-register pointers
phy: qcom-qmp-combo: clean up DP clock callbacks
phy: qcom-qmp-combo: separate clock and provider registration
phy: qcom-qmp-combo: add clock registration helper
...
|
|
- Add DT and driver support for SC8280XP/SA8540P basic interconnects where
interconnect bandwidth must be requested before enabling interconnect
clocks (Johan Hovold)
- Add 'dma-coherent' property (Johan Hovold)
* remotes/lorenzo/pci/qcom:
dt-bindings: PCI: qcom: Allow 'dma-coherent' property
PCI: qcom: Add basic interconnect support
dt-bindings: PCI: qcom: Add SC8280XP/SA8540P interconnects
|
|
On Qualcomm platforms like SC8280XP and SA8540P, interconnect bandwidth
must be requested before enabling interconnect clocks.
Add basic support for managing an optional "pcie-mem" interconnect path
by setting a low constraint before enabling clocks and updating it after
the link is up.
Note that it is not possible for a controller driver to set anything but
a maximum peak bandwidth as expected average bandwidth will vary with
use case and actual use (and power policy?). This very much remains an
unresolved problem with the interconnect framework.
Also note that no constraint is set for the SC8280XP/SA8540P "cpu-pcie"
path for now as it is not clear what an appropriate constraint would be
(and the system does not crash when left unspecified).
Link: https://lore.kernel.org/r/20221102090705.23634-3-johan+linaro@kernel.org
Fixes: 70574511f3fc ("PCI: qcom: Add support for SC8280XP")
Signed-off-by: Johan Hovold <johan+linaro@kernel.org>
Signed-off-by: Lorenzo Pieralisi <lpieralisi@kernel.org>
Reviewed-by: Brian Masney <bmasney@redhat.com>
Reviewed-by: Manivannan Sadhasivam <mani@kernel.org>
Acked-by: Georgi Djakov <djakov@kernel.org>
|
|
Fix the error message to mention "assert" instead of "deassert".
Link: https://lore.kernel.org/r/20221109094039.25753-1-manivannan.sadhasivam@linaro.org
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Lorenzo Pieralisi <lpieralisi@kernel.org>
Reviewed-by: Vinod Koul <vkoul@kernel.org>
|
|
Call phy_set_mode_ext() to notify the PHY driver that the PHY is being
used in the RC mode.
Reviewed-by: Jingoo Han <jingoohan1@gmail.com>
Reviewed-by: Johan Hovold <johan+linaro@kernel.org>
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Acked-by: Lorenzo Pieralisi <lpieralisi@kernel.org>
Link: https://lore.kernel.org/r/20220927092207.161501-5-dmitry.baryshkov@linaro.org
Signed-off-by: Vinod Koul <vkoul@kernel.org>
|
|
Use a more descriptive name for the reset host-init error label for
consistency.
Link: https://lore.kernel.org/r/20220928155421.21660-3-johan+linaro@kernel.org
Signed-off-by: Johan Hovold <johan+linaro@kernel.org>
Signed-off-by: Lorenzo Pieralisi <lpieralisi@kernel.org>
|
|
Drop the unused and confusingly named post_deinit callback that was
added for the now removed pipe clock handling.
If ever needed we can add back a callback named pre_deinit (or perhaps
rather pre_phy_power_off) instead.
Link: https://lore.kernel.org/r/20220928155421.21660-2-johan+linaro@kernel.org
Signed-off-by: Johan Hovold <johan+linaro@kernel.org>
Signed-off-by: Lorenzo Pieralisi <lpieralisi@kernel.org>
|
|
Sort the device-id table entries alphabetically by compatible string to
make it easier to find entries and add new ones.
Link: https://lore.kernel.org/r/20220714071348.6792-9-johan+linaro@kernel.org
Signed-off-by: Johan Hovold <johan+linaro@kernel.org>
Signed-off-by: Lorenzo Pieralisi <lpieralisi@kernel.org>
Reviewed-by: Brian Masney <bmasney@redhat.com>
Acked-by: Stanimir Varbanov <svarbanov@mm-sol.com>
|
|
The various IP versions have different configurations that are encoded
in separate sets of operation callbacks. Currently, there is no need for
also maintaining corresponding sets of data parameters, but it is
conceivable that these may again be found useful (e.g. to implement
minor variations of the operation callbacks).
Rename the default configuration structures after the IP version they
apply to so that they can more easily be reused by different SoCs.
Note that SoC specific configurations can be added later if need arises
(e.g. cfg_sc8280xp).
Link: https://lore.kernel.org/r/20220714071348.6792-8-johan+linaro@kernel.org
Signed-off-by: Johan Hovold <johan+linaro@kernel.org>
Signed-off-by: Lorenzo Pieralisi <lpieralisi@kernel.org>
Reviewed-by: Rob Herring <robh@kernel.org>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Reviewed-by: Brian Masney <bmasney@redhat.com>
Acked-by: Stanimir Varbanov <svarbanov@mm-sol.com>
|
|
The kernel is not a devicetree validator and does not need to re-encode
information which is already available in the devicetree.
This is specifically true for the optional PCIe clocks, some of which
are really interconnect clocks.
Treat also the 2.7.0 optional clocks as truly optional instead of
maintaining a list of clocks per compatible (including two compatible
strings for the two identical controllers on sm8450) just to validate
the devicetree.
Link: https://lore.kernel.org/r/20220714071348.6792-7-johan+linaro@kernel.org
Signed-off-by: Johan Hovold <johan+linaro@kernel.org>
Signed-off-by: Lorenzo Pieralisi <lpieralisi@kernel.org>
Reviewed-by: Rob Herring <robh@kernel.org>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Reviewed-by: Brian Masney <bmasney@redhat.com>
Acked-by: Stanimir Varbanov <svarbanov@mm-sol.com>
|
|
The SA8540P platform has five PCIe controllers: two 4-lane, two 2-lane
and one 1-lane.
Add a new "qcom,pcie-sa8540p" compatible string and reuse the 1.9.0 ops.
Note that like for SC8280XP, the SA8540P controllers need two or three
interconnect clocks to be enabled.
Link: https://lore.kernel.org/r/20220714071348.6792-6-johan+linaro@kernel.org
Signed-off-by: Johan Hovold <johan+linaro@kernel.org>
Signed-off-by: Lorenzo Pieralisi <lpieralisi@kernel.org>
Reviewed-by: Rob Herring <robh@kernel.org>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Reviewed-by: Brian Masney <bmasney@redhat.com>
Acked-by: Stanimir Varbanov <svarbanov@mm-sol.com>
|
|
The SC8280XP platform has seven PCIe controllers: two used with USB4,
two 4-lane, two 2-lane and one 1-lane.
Add a new "qcom,pcie-sc8280xp" compatible string and reuse the 1.9.0
ops.
Note that the SC8280XP controllers need two or three interconnect
clocks to be enabled. Model these as optional clocks to avoid encoding
devicetree data in the PCIe driver.
Note that the same could be done for the SM8450 interconnect clocks and
possibly also for the TBU clocks.
Link: https://lore.kernel.org/r/20220714071348.6792-5-johan+linaro@kernel.org
Signed-off-by: Johan Hovold <johan+linaro@kernel.org>
Signed-off-by: Lorenzo Pieralisi <lpieralisi@kernel.org>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Acked-by: Stanimir Varbanov <svarbanov@mm-sol.com>
|
|
- Add PHY clock source implementation (Dmitry Baryshkov)
- Use new clk_regmap_phy_mux_ops for gcc-sm8450 and gcc-sc7280 PCIe pipe
clocks (Dmitry Baryshkov)
- Set up rev 2.1.0 PARF_PHY before enabling clocks (Christian Marangi)
- Power on PHY before accessing IPQ8074 DBI registers to avoid boot hangs
(Robert Marko)
- Power on PHY before accessing DBI registers on all variants for
consistency (Robert Marko)
- Remove unnecessary pipe_clk handling since this is done in PHY drivers
(Dmitry Baryshkov)
- Drop manual pipe_clk_src handling (Dmitry Baryshkov)
- Move GEN3_RELATED DBI definitions to common dwc header (Baruch Siach)
- Define slot capabilities using generic PCI_EXP_SLTCAP_* macros (Baruch
Siach)
- Add IPQ60xx support (Selvam Sathappan Periakaruppan)
- Fix DT description typo (Baruch Siach)
- Fix DT "compatibles" typo (Johan Hovold)
- Allow ASPM L1 and substates for 2.7.0 (Krishna chaitanya chundru)
* pci/ctrl/qcom:
PCI: qcom: Allow ASPM L1 and substates for 2.7.0
dt-bindings: PCI: qcom: Fix reset conditional
dt-bindings: PCI: qcom: Fix description typo
PCI: qcom: Add IPQ60xx support
PCI: qcom: Define slot capabilities using PCI_EXP_SLTCAP_*
PCI: dwc: Move GEN3_RELATED DBI definitions to common header
PCI: qcom: Drop manual pipe_clk_src handling
PCI: qcom: Remove unnecessary pipe_clk handling
PCI: qcom: Power on PHY before DBI register accesses
PCI: qcom: Power on PHY before IPQ8074 DBI register accesses
PCI: qcom: Set up rev 2.1.0 PARF_PHY before enabling clocks
clk: qcom: gcc-sc7280: use new clk_regmap_phy_mux_ops for PCIe pipe clocks
clk: qcom: gcc-sm8450: use new clk_regmap_phy_mux_ops for PCIe pipe clocks
clk: qcom: regmap: add PHY clock source implementation
|
|
Allow ASPM L1 and its substates. By default this is disabled in the qcom
specific hardware. Enable it explicitly only for controllers belonging to
2_7_0.
This does not affect any link capability registers; it will allow the link
transitions to L1 and its substates only if they are already supported.
Link: https://lore.kernel.org/r/1657886366-32685-1-git-send-email-quic_krichai@quicinc.com
Signed-off-by: Krishna chaitanya chundru <quic_krichai@quicinc.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Acked-by: Stanimir Varbanov <svarbanov@mm-sol.com>
|
|
IPQ60xx series of SoCs have one port of PCIe gen 3. Add support for that
platform.
The code is based on downstream[1] Codeaurora kernel v5.4 (branch
win.linuxopenwrt.2.0).
Split out the DBI registers access part from .init into .post_init. DBI
registers are only accessible after phy_power_on().
[1] https://source.codeaurora.org/quic/qsdk/oss/kernel/linux-ipq-5.4/
Link: https://lore.kernel.org/r/f7f848653c99abbf9a0f877949a44e52329543ae.1655799816.git.baruch@tkos.co.il
Tested-by: Robert Marko <robert.marko@sartura.hr>
Signed-off-by: Selvam Sathappan Periakaruppan <quic_speriaka@quicinc.com>
Signed-off-by: Baruch Siach <baruch.siach@siklu.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Reviewed-by: Johan Hovold <johan+linaro@kernel.org>
Acked-by: Stanimir Varbanov <svarbanov@mm-sol.com>
|
