| Age | Commit message (Collapse) | Author |
|---|
|
Nexthop finalization consists of two steps: the part where the offload is
removed, because the backing RIF is now gone; and the part where the
association to the RIF is severed.
Extract from mlxsw_sp_nexthop_type_fini() a helper that covers the
unoffloading part, mlxsw_sp_nexthop_type_rif_gone(), so that it can later
be called independently.
Note that this swaps around the ordering of mlxsw_sp_nexthop_ipip_fini()
vs. mlxsw_sp_nexthop_rif_fini(). The current ordering is more of a
historical happenstance than a conscious decision. The two cleanups do not
depend on each other, and this change should have no observable effects.
Signed-off-by: Petr Machata <petrm@nvidia.com>
Reviewed-by: Danielle Ratson <danieller@nvidia.com>
Link: https://lore.kernel.org/r/7134559534c5f5c4807c3a1569fae56f8887e763.1687438411.git.petrm@nvidia.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
A previous patch added a pointer to loopback CRIF to the router data
structure. That makes the loopback RIF index redundant, as everything
necessary can be derived from the CRIF. Drop the field and adjust the code
accordingly.
Signed-off-by: Petr Machata <petrm@nvidia.com>
Reviewed-by: Danielle Ratson <danieller@nvidia.com>
Link: https://lore.kernel.org/r/8637bf959bc5b6c9d5184b9bd8a0cd53c5132835.1687438411.git.petrm@nvidia.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
When a RIF is about to be created, the registration of the netdevice that
it should be associated with must have been seen in the past, and a CRIF
created. Therefore make this a hard requirement by looking up the CRIF
during RIF creation, and complaining loudly when there isn't one.
This then allows to keep a link between a RIF and its corresponding
CRIF (and back, as the relationship is one-to-at-most-one), which do.
The CRIF will later be useful as the objects tracked there will be
offloaded lazily as a result of RIF creation.
CRIFs are created when an "interesting" netdevice is registered, and
destroyed after such device is unregistered. CRIFs are supposed to already
exist when a RIF creation request arises, and exist at least as long as
that RIF exists. This makes for a simple invariant: it is always safe to
dereference CRIF pointer from "its" RIF.
To guarantee this, CRIFs cannot be removed immediately when the UNREGISTER
event is delivered. The reason is that if a RIF's netdevices has an IPv6
address, removal of this address is notified in an atomic block. To remove
the RIF, the IPv6 removal handler schedules a work item. It must be safe
for this work item to access the associated CRIF as well.
Thus when a netdevice that backs the CRIF is removed, if it still has a
RIF, do not actually free the CRIF, only toggle its can_destroy flag, which
this patch adds. Later on, mlxsw_sp_rif_destroy() collects the CRIF.
Signed-off-by: Petr Machata <petrm@nvidia.com>
Reviewed-by: Danielle Ratson <danieller@nvidia.com>
Link: https://lore.kernel.org/r/68c8e33afa6b8c03c431b435e1685ffdff752e63.1687438411.git.petrm@nvidia.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
CRIFs are generally not maintained for loopback RIFs. However, the RIF for
the default VRF is used for offloading of blackhole nexthops. Nexthops
expect to have a valid CRIF. Therefore in this patch, add code to maintain
CRIF for the loopback RIF as well.
Signed-off-by: Petr Machata <petrm@nvidia.com>
Reviewed-by: Danielle Ratson <danieller@nvidia.com>
Link: https://lore.kernel.org/r/7f2b2fcc98770167ed1254a904c3f7f585ba43f0.1687438411.git.petrm@nvidia.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
CRIFs are objects that mlxsw maintains for netdevices that may not have an
associated RIF (i.e. they may not have been instantiated in the ASIC), but
if indeed they do not, it is quite possible they will in the future. These
netdevices are candidate RIFs, hence CRIFs. Netdevices for which CRIFs are
created include e.g. bridges, LAGs, or front panel ports. The idea is that
next hops would be kept at CRIFs, not RIFs, and thus it would be easier to
offload and unoffload the entities that have been added before the RIF was
created.
In this patch, add the code for low-level CRIF maintenance: create and
destroy, and keep in a table keyed by the netdevice pointer for easy
recall.
Signed-off-by: Petr Machata <petrm@nvidia.com>
Reviewed-by: Danielle Ratson <danieller@nvidia.com>
Link: https://lore.kernel.org/r/186d44e399c475159da20689f2c540719f2d1ed0.1687438411.git.petrm@nvidia.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
The current function, mlxsw_sp_router_ul_rif_get(), is a wrapper around the
function mentioned in the subject. As such it forms an external interface
of the router code.
In future patches we will want to maintain connection between RIFs and the
CRIFs (introduced in the next patch) that back them. That will not hold
for the VRF-based loopback netdevices, so the whole CRIF business can be
kept hidden from the rest of mlxsw.
But for the main VRF loopback RIF we do want to keep the RIF-CRIF
connection, because that RIF is used for blackhole next hops, and the next
hop code can be kept simpler for assuming rif->crif is valid.
Hence, instead, call mlxsw_sp_ul_rif_get() to create the main VRF loopback
RIF. This being an internal function will take the CRIF argument anyway.
Furthermore, the function does not lock, which is not necessary at this
point in code yet.
Signed-off-by: Petr Machata <petrm@nvidia.com>
Reviewed-by: Danielle Ratson <danieller@nvidia.com>
Link: https://lore.kernel.org/r/7a39a011a02a84164cd7f5da7985ec5b2ae01ba5.1687438411.git.petrm@nvidia.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
The extack will be handy in later patches.
Signed-off-by: Petr Machata <petrm@nvidia.com>
Reviewed-by: Danielle Ratson <danieller@nvidia.com>
Link: https://lore.kernel.org/r/e87ba300121010d580b80a281877573a7b1377ca.1687438411.git.petrm@nvidia.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Drivers must not assume in their ndo_start_xmit() that
skbs have their mac_header set. skb->data is all what is needed.
bonding seems to be one of the last offender as caught by syzbot:
WARNING: CPU: 1 PID: 12155 at include/linux/skbuff.h:2907 skb_mac_offset include/linux/skbuff.h:2913 [inline]
WARNING: CPU: 1 PID: 12155 at include/linux/skbuff.h:2907 bond_xmit_hash drivers/net/bonding/bond_main.c:4170 [inline]
WARNING: CPU: 1 PID: 12155 at include/linux/skbuff.h:2907 bond_xmit_3ad_xor_slave_get drivers/net/bonding/bond_main.c:5149 [inline]
WARNING: CPU: 1 PID: 12155 at include/linux/skbuff.h:2907 bond_3ad_xor_xmit drivers/net/bonding/bond_main.c:5186 [inline]
WARNING: CPU: 1 PID: 12155 at include/linux/skbuff.h:2907 __bond_start_xmit drivers/net/bonding/bond_main.c:5442 [inline]
WARNING: CPU: 1 PID: 12155 at include/linux/skbuff.h:2907 bond_start_xmit+0x14ab/0x19d0 drivers/net/bonding/bond_main.c:5470
Modules linked in:
CPU: 1 PID: 12155 Comm: syz-executor.3 Not tainted 6.1.30-syzkaller #0
Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS Google 05/25/2023
RIP: 0010:skb_mac_header include/linux/skbuff.h:2907 [inline]
RIP: 0010:skb_mac_offset include/linux/skbuff.h:2913 [inline]
RIP: 0010:bond_xmit_hash drivers/net/bonding/bond_main.c:4170 [inline]
RIP: 0010:bond_xmit_3ad_xor_slave_get drivers/net/bonding/bond_main.c:5149 [inline]
RIP: 0010:bond_3ad_xor_xmit drivers/net/bonding/bond_main.c:5186 [inline]
RIP: 0010:__bond_start_xmit drivers/net/bonding/bond_main.c:5442 [inline]
RIP: 0010:bond_start_xmit+0x14ab/0x19d0 drivers/net/bonding/bond_main.c:5470
Code: 8b 7c 24 30 e8 76 dd 1a 01 48 85 c0 74 0d 48 89 c3 e8 29 67 2e fe e9 15 ef ff ff e8 1f 67 2e fe e9 10 ef ff ff e8 15 67 2e fe <0f> 0b e9 45 f8 ff ff e8 09 67 2e fe e9 dc fa ff ff e8 ff 66 2e fe
RSP: 0018:ffffc90002fff6e0 EFLAGS: 00010283
RAX: ffffffff835874db RBX: 000000000000ffff RCX: 0000000000040000
RDX: ffffc90004dcf000 RSI: 00000000000000b5 RDI: 00000000000000b6
RBP: ffffc90002fff8b8 R08: ffffffff83586d16 R09: ffffffff83586584
R10: 0000000000000007 R11: ffff8881599fc780 R12: ffff88811b6a7b7e
R13: 1ffff110236d4f6f R14: ffff88811b6a7ac0 R15: 1ffff110236d4f76
FS: 00007f2e9eb47700(0000) GS:ffff8881f6b00000(0000) knlGS:0000000000000000
CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033
CR2: 0000001b2e421000 CR3: 000000010e6d4000 CR4: 00000000003526e0
DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000
DR3: 0000000000000000 DR6: 00000000fffe0ff0 DR7: 0000000000000400
Call Trace:
<TASK>
[<ffffffff8471a49f>] netdev_start_xmit include/linux/netdevice.h:4925 [inline]
[<ffffffff8471a49f>] __dev_direct_xmit+0x4ef/0x850 net/core/dev.c:4380
[<ffffffff851d845b>] dev_direct_xmit include/linux/netdevice.h:3043 [inline]
[<ffffffff851d845b>] packet_direct_xmit+0x18b/0x300 net/packet/af_packet.c:284
[<ffffffff851c7472>] packet_snd net/packet/af_packet.c:3112 [inline]
[<ffffffff851c7472>] packet_sendmsg+0x4a22/0x64d0 net/packet/af_packet.c:3143
[<ffffffff8467a4b2>] sock_sendmsg_nosec net/socket.c:716 [inline]
[<ffffffff8467a4b2>] sock_sendmsg net/socket.c:736 [inline]
[<ffffffff8467a4b2>] __sys_sendto+0x472/0x5f0 net/socket.c:2139
[<ffffffff8467a715>] __do_sys_sendto net/socket.c:2151 [inline]
[<ffffffff8467a715>] __se_sys_sendto net/socket.c:2147 [inline]
[<ffffffff8467a715>] __x64_sys_sendto+0xe5/0x100 net/socket.c:2147
[<ffffffff8553071f>] do_syscall_x64 arch/x86/entry/common.c:50 [inline]
[<ffffffff8553071f>] do_syscall_64+0x2f/0x50 arch/x86/entry/common.c:80
[<ffffffff85600087>] entry_SYSCALL_64_after_hwframe+0x63/0xcd
Fixes: 7b8fc0103bb5 ("bonding: add a vlan+srcmac tx hashing option")
Reported-by: syzbot <syzkaller@googlegroups.com>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Jarod Wilson <jarod@redhat.com>
Cc: Moshe Tal <moshet@nvidia.com>
Cc: Jussi Maki <joamaki@gmail.com>
Cc: Jay Vosburgh <j.vosburgh@gmail.com>
Cc: Andy Gospodarek <andy@greyhouse.net>
Cc: Vladimir Oltean <vladimir.oltean@nxp.com>
Link: https://lore.kernel.org/r/20230622152304.2137482-1-edumazet@google.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
With support for Ethernet PHY LEDs having been added, while
unregistering a MDIO bus and its child device liks PHYs there may be
"late" accesses to the MDIO bus. One typical use case is setting the PHY
LEDs brightness to OFF for instance.
We need to ensure that the MDIO bus controller remains entirely
functional since it runs off the main GENET adapter clock.
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/all/20230617155500.4005881-1-andrew@lunn.ch/
Fixes: 9a4e79697009 ("net: bcmgenet: utilize generic Broadcom UniMAC MDIO controller driver")
Signed-off-by: Florian Fainelli <florian.fainelli@broadcom.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://lore.kernel.org/r/20230622103107.1760280-1-florian.fainelli@broadcom.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
As xa_get_mark() returns false in case the entry is not present,
no need to redundantly check if vport is present. Remove the lookup.
Signed-off-by: Jiri Pirko <jiri@nvidia.com>
Reviewed-by: Shay Drory <shayd@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
|
|
Since mlx5_esw_query_vport_vhca_id() could be called either from
mlx5_esw_vport_enable() or mlx5_esw_vport_disable() where the
the check is done, this is always false here.
Remove the redundant check.
Signed-off-by: Jiri Pirko <jiri@nvidia.com>
Reviewed-by: Shay Drory <shayd@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
|
|
is_ib_rep_supported()
is_mdev_switchdev_mode() check is done in is_eth_rep_supported().
Function is_ib_rep_supported() calls is_eth_rep_supported().
Remove the redundant check from it.
Signed-off-by: Jiri Pirko <jiri@nvidia.com>
Reviewed-by: Shay Drory <shayd@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
|
|
is_ib_rep_supported()
MLX5_ESWITCH_MANAGER() check is done in is_eth_rep_supported().
Function is_ib_rep_supported() calls is_eth_rep_supported().
Remove the redundant check from it.
Signed-off-by: Jiri Pirko <jiri@nvidia.com>
Reviewed-by: Shay Drory <shayd@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
|
|
On error flow resources being freed in esw_master_egress_destroy_resources()
but pointers not being set to null if error flow is from creating a
bounce rule. Then in esw_acl_egress_ofld_cleanup() we try to access already
freed pointers. Fix it by resetting the pointers to null.
Also if error is from creating a second or later bounce rule then the
flow group and table being used and cannot and should not be freed.
Add a check to destroy the flow group and table if there are no bounce
rules.
mlx5_core.sf mlx5_core.sf.2: mlx5_destroy_flow_group:2306:(pid 2235): Flow group 4 wasn't destroyed, refcount > 1
mlx5_core.sf mlx5_core.sf.2: mlx5_destroy_flow_table:2295:(pid 2235): Flow table 3 wasn't destroyed, refcount > 1
Fixes: 5e0202eb49ed ("net/mlx5: E-switch, Handle multiple master egress rules")
Signed-off-by: Roi Dayan <roid@nvidia.com>
Reviewed-by: Shay Drory <shayd@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
|
|
The function comment says what it is and the comment
is redundant.
Signed-off-by: Roi Dayan <roid@nvidia.com>
Reviewed-by: Shay Drory <shayd@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
|
|
When creating flow table for shared fdb resources, there is
only need to pass other_vport flag if vport is not 0 or
if the port is ECPF in BlueField.
Signed-off-by: Roi Dayan <roid@nvidia.com>
Reviewed-by: Shay Drory <shayd@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
|
|
To allow devcom events on E-Switch that is not a vport group manager,
use vhca id as an index instead of device index which might be shared
between several E-Switches. for example SF and its PF.
Signed-off-by: Roi Dayan <roid@nvidia.com>
Reviewed-by: Shay Drory <shayd@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
|
|
Add peer fdb rules for E-Switch that are vport managers or ecpf device.
It is not needed for other devices.
Signed-off-by: Roi Dayan <roid@nvidia.com>
Reviewed-by: Shay Drory <shayd@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
|
|
Device index is like PF index and limited to max physical ports.
For example, SFs created under PF the device index is the PF device index.
Use vhca_id which gets the FW index per vport, for vport rx rules
and vport pair events.
Signed-off-by: Roi Dayan <roid@nvidia.com>
Reviewed-by: Shay Drory <shayd@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
|
|
Remove duplicate function for checking if device has lag support.
Signed-off-by: Roi Dayan <roid@nvidia.com>
Reviewed-by: Shay Drory <shayd@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
|
|
The mlx5_is_reset_now_capable() function returns bool, not negative
error codes. So if fast teardown is not supported it should return
false instead of -EOPNOTSUPP.
Fixes: 92501fa6e421 ("net/mlx5: Ack on sync_reset_request only if PF can do reset_now")
Signed-off-by: Dan Carpenter <dan.carpenter@linaro.org>
Reviewed-by: Kalesh AP <kalesh-anakkur.purayil@broadcom.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
|
|
mlx5_eswitch_cleanup() is using esw right after freeing it for
releasing devlink_param.
Fix it by releasing the devlink_param before freeing the esw, and
adjust the create function accordingly.
Fixes: 3f90840305e2 ("net/mlx5: Move esw multiport devlink param to eswitch code")
Reported-by: Dan Carpenter <dan.carpenter@linaro.org>
Signed-off-by: Shay Drory <shayd@nvidia.com>
Reviewed-by: Automatic Verification <verifier@nvidia.com>
Reviewed-by: Gal Pressman <gal@nvidia.com>
Reviewed-by: Moshe Shemesh <moshe@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
|
|
Several functions in the hns3 driver have unused parameters.
The compiler will warn about them when building
with -Wunused-parameter option of hns3.
Signed-off-by: Peiyang Wang <wangpeiyang1@huawei.com>
Signed-off-by: Hao Lan <lanhao@huawei.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
Now, strncpy() in hns3_dbg_fill_content() use src-length as copy-length,
it may result in dest-buf overflow.
This patch is to fix intel compile warning for csky-linux-gcc (GCC) 12.1.0
compiler.
The warning reports as below:
hclge_debugfs.c:92:25: warning: 'strncpy' specified bound depends on
the length of the source argument [-Wstringop-truncation]
strncpy(pos, items[i].name, strlen(items[i].name));
hclge_debugfs.c:90:25: warning: 'strncpy' output truncated before
terminating nul copying as many bytes from a string as its length
[-Wstringop-truncation]
strncpy(pos, result[i], strlen(result[i]));
strncpy() use src-length as copy-length, it may result in
dest-buf overflow.
So,this patch add some values check to avoid this issue.
Signed-off-by: Hao Chen <chenhao418@huawei.com>
Reported-by: kernel test robot <lkp@intel.com>
Closes: https://lore.kernel.org/lkml/202207170606.7WtHs9yS-lkp@intel.com/T/
Signed-off-by: Hao Lan <lanhao@huawei.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
The result of expression '(k ^ ~v) & k' is exactly
the same with 'k & v', so simplify it.
(k ^ ~v) & k == k & v
The truth table (in non table form):
k == 0, v == 0:
(k ^ ~v) & k == (0 ^ ~0) & 0 == (0 ^ 1) & 0 == 1 & 0 == 0
k & v == 0 & 0 == 0
k == 0, v == 1:
(k ^ ~v) & k == (0 ^ ~1) & 0 == (0 ^ 0) & 0 == 1 & 0 == 0
k & v == 0 & 1 == 0
k == 1, v == 0:
(k ^ ~v) & k == (1 ^ ~0) & 1 == (1 ^ 1) & 1 == 0 & 1 == 0
k & v == 1 & 0 == 0
k == 1, v == 1:
(k ^ ~v) & k == (1 ^ ~1) & 1 == (1 ^ 0) & 1 == 1 & 1 == 1
k & v == 1 & 1 == 1
Signed-off-by: Jian Shen <shenjian15@huawei.com>
Signed-off-by: Hao Lan <lanhao@huawei.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/wireless/wireless-next
Johannes Berg says:
====================
Notable changes this time around:
MAINTAINERS
- add missing driver git trees
ath11k
- factory test mode support
iwlwifi
- config rework to drop test devices and
split the different families
- major update for new firmware and MLO
stack
- initial multi-link reconfiguration suppor
- multi-BSSID and MLO improvements
other
- fix the last few W=1 warnings from GCC 13
- merged wireless tree to avoid conflicts
* tag 'wireless-next-2023-06-22' of git://git.kernel.org/pub/scm/linux/kernel/git/wireless/wireless-next: (245 commits)
wifi: ieee80211: fix erroneous NSTR bitmap size checks
wifi: rtlwifi: cleanup USB interface
wifi: rtlwifi: simplify LED management
wifi: ath10k: improve structure padding
wifi: ath9k: convert msecs to jiffies where needed
wifi: iwlwifi: mvm: Add support for IGTK in D3 resume flow
wifi: iwlwifi: mvm: update two most recent GTKs on D3 resume flow
wifi: iwlwifi: mvm: Refactor security key update after D3
wifi: mac80211: mark keys as uploaded when added by the driver
wifi: iwlwifi: remove support of A0 version of FM RF
wifi: iwlwifi: cfg: clean up Bz module firmware lines
wifi: iwlwifi: pcie: add device id 51F1 for killer 1675
wifi: iwlwifi: bump FW API to 83 for AX/BZ/SC devices
wifi: iwlwifi: cfg: remove trailing dash from FW_PRE constants
wifi: iwlwifi: also unify Ma device configurations
wifi: iwlwifi: also unify Sc device configurations
wifi: iwlwifi: unify Bz/Gl device configurations
wifi: iwlwifi: pcie: also drop jacket from info macro
wifi: iwlwifi: remove support for *nJ devices
wifi: iwlwifi: don't load old firmware for 22000
...
====================
Link: https://lore.kernel.org/r/20230622185602.147650-2-johannes@sipsolutions.net
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/mkl/linux-can-next
Marc Kleine-Budde says:
====================
pull-request: can-next 2023-06-22
The first patch is by Carsten Schmidt, targets the kvaser_usb driver
and adds len8_dlc support.
Marcel Hellwig's patch for the xilinx_can driver adds support for CAN
transceivers via the PHY framework.
Frank Jungclaus contributes 6+2 patches for the esd_usb driver in
preparation for the upcoming CAN-USB/3 support.
The 2 patches by Miquel Raynal for the sja1000 driver work around
overruns stalls on the Renesas SoCs.
The next 3 patches are by me and fix the coding style in the
rx-offload helper and in the m_can and ti_hecc driver.
Vincent Mailhol contributes 3 patches to fix and update the
calculation of the length of CAN frames on the wire.
Oliver Hartkopp's patch moves the CAN_RAW_FILTER_MAX definition into
the correct header.
The remaining 14 patches are by Jimmy Assarsson, target the
kvaser_pciefd driver and bring various updates and improvements.
* tag 'linux-can-next-for-6.5-20230622' of git://git.kernel.org/pub/scm/linux/kernel/git/mkl/linux-can-next: (33 commits)
can: kvaser_pciefd: Use TX FIFO size read from CAN controller
can: kvaser_pciefd: Refactor code
can: kvaser_pciefd: Add len8_dlc support
can: kvaser_pciefd: Use FIELD_{GET,PREP} and GENMASK where appropriate
can: kvaser_pciefd: Sort register definitions
can: kvaser_pciefd: Change return type for kvaser_pciefd_{receive,transmit,set_tx}_irq()
can: kvaser_pciefd: Rename device ID defines
can: kvaser_pciefd: Sort includes in alphabetic order
can: kvaser_pciefd: Remove SPI flash parameter read functionality
can: uapi: move CAN_RAW_FILTER_MAX definition to raw.h
can: kvaser_pciefd: Define unsigned constants with type suffix 'U'
can: kvaser_pciefd: Set hardware timestamp on transmitted packets
can: kvaser_pciefd: Add function to set skb hwtstamps
can: kvaser_pciefd: Remove handler for unused KVASER_PCIEFD_PACK_TYPE_EFRAME_ACK
can: kvaser_pciefd: Remove useless write to interrupt register
can: length: refactor frame lengths definition to add size in bits
can: length: fix bitstuffing count
can: length: fix description of the RRS field
can: m_can: fix coding style
can: ti_hecc: fix coding style
...
====================
Link: https://lore.kernel.org/r/20230622082658.571150-1-mkl@pengutronix.de
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
When processing counter updates, if any action set using the newly
incremented counter includes an encap action, prod the corresponding
neighbouring entry to indicate to the neighbour cache that the entry
is still in use and passing traffic.
Signed-off-by: Edward Cree <ecree.xilinx@gmail.com>
Link: https://lore.kernel.org/r/20230621121504.17004-1-edward.cree@amd.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
The QCA8K switch supports additional modes that can be handled in
hardware for the LED netdev trigger.
Add these additional modes to further support the Switch LEDs and
offload more blink modes.
Add additional modes:
- link_10
- link_100
- link_1000
- half_duplex
- full_duplex
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com>
Link: https://lore.kernel.org/r/20230621095409.25859-1-ansuelsmth@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
In a setup where a Thunderbolt hub connects to Ethernet and a display
through USB Type-C, users may experience a hung task timeout when they
remove the cable between the PC and the Thunderbolt hub.
This is because the igb_down function is called multiple times when
the Thunderbolt hub is unplugged. For example, the igb_io_error_detected
triggers the first call, and the igb_remove triggers the second call.
The second call to igb_down will block at napi_synchronize.
Here's the call trace:
__schedule+0x3b0/0xddb
? __mod_timer+0x164/0x5d3
schedule+0x44/0xa8
schedule_timeout+0xb2/0x2a4
? run_local_timers+0x4e/0x4e
msleep+0x31/0x38
igb_down+0x12c/0x22a [igb 6615058754948bfde0bf01429257eb59f13030d4]
__igb_close+0x6f/0x9c [igb 6615058754948bfde0bf01429257eb59f13030d4]
igb_close+0x23/0x2b [igb 6615058754948bfde0bf01429257eb59f13030d4]
__dev_close_many+0x95/0xec
dev_close_many+0x6e/0x103
unregister_netdevice_many+0x105/0x5b1
unregister_netdevice_queue+0xc2/0x10d
unregister_netdev+0x1c/0x23
igb_remove+0xa7/0x11c [igb 6615058754948bfde0bf01429257eb59f13030d4]
pci_device_remove+0x3f/0x9c
device_release_driver_internal+0xfe/0x1b4
pci_stop_bus_device+0x5b/0x7f
pci_stop_bus_device+0x30/0x7f
pci_stop_bus_device+0x30/0x7f
pci_stop_and_remove_bus_device+0x12/0x19
pciehp_unconfigure_device+0x76/0xe9
pciehp_disable_slot+0x6e/0x131
pciehp_handle_presence_or_link_change+0x7a/0x3f7
pciehp_ist+0xbe/0x194
irq_thread_fn+0x22/0x4d
? irq_thread+0x1fd/0x1fd
irq_thread+0x17b/0x1fd
? irq_forced_thread_fn+0x5f/0x5f
kthread+0x142/0x153
? __irq_get_irqchip_state+0x46/0x46
? kthread_associate_blkcg+0x71/0x71
ret_from_fork+0x1f/0x30
In this case, igb_io_error_detected detaches the network interface
and requests a PCIE slot reset, however, the PCIE reset callback is
not being invoked and thus the Ethernet connection breaks down.
As the PCIE error in this case is a non-fatal one, requesting a
slot reset can be avoided.
This patch fixes the task hung issue and preserves Ethernet
connection by ignoring non-fatal PCIE errors.
Signed-off-by: Ying Hsu <yinghsu@chromium.org>
Tested-by: Pucha Himasekhar Reddy <himasekharx.reddy.pucha@intel.com> (A Contingent worker at Intel)
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Link: https://lore.kernel.org/r/20230620174732.4145155-1-anthony.l.nguyen@intel.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
According to the errata sheets for ksz9477 and ksz9567, writes to the
PHY registers 0x10-0x1f (i.e. those located at addresses 0xN120 to
0xN13f) must be done as a 32 bit write to the 4-byte aligned address
containing the register, hence requires a RMW in order not to change
the adjacent PHY register.
Signed-off-by: Rasmus Villemoes <linux@rasmusvillemoes.dk>
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://lore.kernel.org/r/20230620113855.733526-4-linux@rasmusvillemoes.dk
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
This will be used in a subsequent patch fixing an errata for writes to
certain PHY registers.
Signed-off-by: Rasmus Villemoes <linux@rasmusvillemoes.dk>
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Acked-by: Arun Ramadoss <arun.ramadoss@microchip.com>
Link: https://lore.kernel.org/r/20230620113855.733526-3-linux@rasmusvillemoes.dk
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Implement ksz_prmw8() in terms of ksz_rmw8(), just as all the other
ksz_pX are implemented in terms of ksz_X. No functional change.
Signed-off-by: Rasmus Villemoes <linux@rasmusvillemoes.dk>
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Acked-by: Arun Ramadoss <arun.ramadoss@microchip.com>
Link: https://lore.kernel.org/r/20230620113855.733526-2-linux@rasmusvillemoes.dk
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Half a year passed since commit 049fe5365324c ("net: txgbe: Add operations
to interact with firmware") was submitted, the buffer in
txgbe_calc_eeprom_checksum was not used. So remove it and the related
branch codes.
Reported-by: kernel test robot <lkp@intel.com>
Closes: https://lore.kernel.org/oe-kbuild-all/202306200242.FXsHokaJ-lkp@intel.com/
Reviewed-by: Jiawen Wu <jiawenwu@trustnetic.com>
Signed-off-by: Zhengchao Shao <shaozhengchao@huawei.com>
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Link: https://lore.kernel.org/r/20230620062519.1575298-1-shaozhengchao@huawei.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Fix an issue where the kernel would stall during netboot, showing the
"sched: RT throttling activated" message. This stall was triggered by
the behavior of the mii_interrupt bit (Bit 7 - DP83TD510E_STS_MII_INT)
in the DP83TD510E's PHY_STS Register (Address = 0x10). The DP83TD510E
datasheet (2020) states that the bit clears on write, however, in
practice, the bit clears on read.
This discrepancy had significant implications on the driver's interrupt
handling. The PHY_STS Register was used by handle_interrupt() to check
for pending interrupts and by read_status() to get the current link
status. The call to read_status() was unintentionally clearing the
mii_interrupt status bit without deasserting the IRQ pin, causing
handle_interrupt() to miss other pending interrupts. This issue was most
apparent during netboot.
The fix refrains from using the PHY_STS Register for interrupt handling.
Instead, we now solely rely on the INTERRUPT_REG_1 Register (Address =
0x12) and INTERRUPT_REG_2 Register (Address = 0x13) for this purpose.
These registers directly influence the IRQ pin state and are latched
high until read.
Note: The INTERRUPT_REG_2 Register (Address = 0x13) exists and can also
be used for interrupt handling, specifically for "Aneg page received
interrupt" and "Polarity change interrupt". However, these features are
currently not supported by this driver.
Fixes: 165cd04fe253 ("net: phy: dp83td510: Add support for the DP83TD510 Ethernet PHY")
Cc: <stable@vger.kernel.org>
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://lore.kernel.org/r/20230621043848.3806124-1-o.rempel@pengutronix.de
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Update macb's embedded PCS drivers to use neg_mode, even though it
makes no use of it or the "mode" argument. This makes the driver
consistent with converted drivers.
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Link: https://lore.kernel.org/r/E1qA8Eo-00EaGX-KJ@rmk-PC.armlinux.org.uk
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Update mt7530's embedded PCS driver to use neg_mode, even though it
makes no use of it or the "mode" argument. This makes the driver
consistent with converted drivers.
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Link: https://lore.kernel.org/r/E1qA8Ej-00EaGR-Fk@rmk-PC.armlinux.org.uk
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Update B53's embedded PCS driver to use neg_mode, even though it makes
no use of it or the "mode" argument. This makes the driver consistent
with converted drivers.
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Acked-by: Florian Fainelli <florian.fainelli@broadcom.com>
Link: https://lore.kernel.org/r/E1qA8Ee-00EaGL-Az@rmk-PC.armlinux.org.uk
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Update Sparx5's embedded PCS driver to use neg_mode rather than the
mode argument. As there is no pcs_link_up() method, this only affects
the pcs_config() method.
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Link: https://lore.kernel.org/r/E1qA8EZ-00EaGF-6F@rmk-PC.armlinux.org.uk
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Update qca8k's embedded PCS driver to use neg_mode rather than the
mode argument. As there is no pcs_link_up() method, this only affects
the pcs_config() method.
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Link: https://lore.kernel.org/r/E1qA8EU-00EaG9-1l@rmk-PC.armlinux.org.uk
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Update prestera's embedded PCS driver to use neg_mode rather than the
mode argument. As there is no pcs_link_up() method, this only affects
the pcs_config() method.
Acked-by: Elad Nachman <enachman@marvell.com>
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Link: https://lore.kernel.org/r/E1qA8EO-00EaG3-TR@rmk-PC.armlinux.org.uk
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Update mvpp2's embedded PCS drivers to use neg_mode rather than the
mode argument, remembering to update the ACPI path as well. As there
are no pcs_link_up() methods, this only affects the two pcs_config()
methods.
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Link: https://lore.kernel.org/r/E1qA8EJ-00EaFx-P6@rmk-PC.armlinux.org.uk
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Update mvneta's embedded PCS driver to use neg_mode rather than the
mode argument. As there is no pcs_link_up() method, this only affects
the pcs_config() method.
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Link: https://lore.kernel.org/r/E1qA8EE-00EaFr-Kx@rmk-PC.armlinux.org.uk
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Update lan966x's embedded PCS driver to use neg_mode rather than the
mode argument. As there is no pcs_link_up() method, this only affects
the pcs_config() method.
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Link: https://lore.kernel.org/r/E1qA8E9-00EaFl-GN@rmk-PC.armlinux.org.uk
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Update the Lynx PCS driver to use neg_mode rather than the mode
argument. This ensures that the link_up() method will always program
the speed and duplex when negotiation is disabled.
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Link: https://lore.kernel.org/r/E1qA8E4-00EaFf-Bf@rmk-PC.armlinux.org.uk
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Update the Lynxi PCS driver to use neg_mode rather than the mode
argument. This ensures that the link_up() method will always program
the speed and duplex when negotiation is disabled.
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Link: https://lore.kernel.org/r/E1qA8Dz-00EaFY-5A@rmk-PC.armlinux.org.uk
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Update xpcs to use neg_mode to configure whether inband negotiation
should be used. We need to update sja1105 as well as that directly
calls into the XPCS driver's config function.
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Link: https://lore.kernel.org/r/E1qA8Dt-00EaFS-W9@rmk-PC.armlinux.org.uk
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Convert fman_dtsec, xilinx_axienet and pcs-lynx to pass the neg_mode
into phylink_mii_c22_pcs_config(). Where appropriate, drivers are
updated to have neg_mode passed into their pcs_config() and
pcs_link_up() functions. For other drivers, we just hoist the call
to phylink_pcs_neg_mode() to their pcs_config() method out of
phylink_mii_c22_pcs_config().
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Link: https://lore.kernel.org/r/E1qA8Do-00EaFM-Ra@rmk-PC.armlinux.org.uk
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Use phylink_pcs_neg_mode() for phylink_mii_c22_pcs_config(). This
results in no functional change.
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Link: https://lore.kernel.org/r/E1qA8Dj-00EaFG-Mt@rmk-PC.armlinux.org.uk
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
PCS have to work out whether they should enable PCS negotiation by
looking at the "mode" and "interface" arguments, and the Autoneg bit
in the advertising mask.
This leads to some complex logic, so lets pull that out into phylink
and instead pass a "neg_mode" argument to the PCS configuration and
link up methods, instead of the "mode" argument.
In order to transition drivers, add a "neg_mode" flag to the phylink
PCS structure to PCS can indicate whether they want to be passed the
neg_mode or the old mode argument.
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Link: https://lore.kernel.org/r/E1qA8De-00EaFA-Ht@rmk-PC.armlinux.org.uk
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
