summaryrefslogtreecommitdiff
path: root/drivers/net
AgeCommit message (Collapse)Author
2025-05-22tsnep: fix timestamping with a stacked DSA driverGerhard Engleder
[ Upstream commit b3ca9eef6646576ad506a96d941d87a69f66732a ] This driver is susceptible to a form of the bug explained in commit c26a2c2ddc01 ("gianfar: Fix TX timestamping with a stacked DSA driver") and in Documentation/networking/timestamping.rst section "Other caveats for MAC drivers", specifically it timestamps any skb which has SKBTX_HW_TSTAMP, and does not consider if timestamping has been enabled in adapter->hwtstamp_config.tx_type. Evaluate the proper TX timestamping condition only once on the TX path (in tsnep_xmit_frame_ring()) and store the result in an additional TX entry flag. Evaluate the new TX entry flag in the TX confirmation path (in tsnep_tx_poll()). This way SKBTX_IN_PROGRESS is set by the driver as required, but never evaluated. SKBTX_IN_PROGRESS shall not be evaluated as it can be set by a stacked DSA driver and evaluating it would lead to unwanted timestamps. Fixes: 403f69bbdbad ("tsnep: Add TSN endpoint Ethernet MAC driver") Suggested-by: Vladimir Oltean <vladimir.oltean@nxp.com> Signed-off-by: Gerhard Engleder <gerhard@engleder-embedded.com> Reviewed-by: Vladimir Oltean <vladimir.oltean@nxp.com> Link: https://patch.msgid.link/20250514195657.25874-1-gerhard@engleder-embedded.com Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
2025-05-22mlxsw: spectrum_router: Fix use-after-free when deleting GRE net devicesIdo Schimmel
[ Upstream commit 92ec4855034b2c4d13f117558dc73d20581fa9ff ] The driver only offloads neighbors that are constructed on top of net devices registered by it or their uppers (which are all Ethernet). The device supports GRE encapsulation and decapsulation of forwarded traffic, but the driver will not offload dummy neighbors constructed on top of GRE net devices as they are not uppers of its net devices: # ip link add name gre1 up type gre tos inherit local 192.0.2.1 remote 198.51.100.1 # ip neigh add 0.0.0.0 lladdr 0.0.0.0 nud noarp dev gre1 $ ip neigh show dev gre1 nud noarp 0.0.0.0 lladdr 0.0.0.0 NOARP (Note that the neighbor is not marked with 'offload') When the driver is reloaded and the existing configuration is replayed, the driver does not perform the same check regarding existing neighbors and offloads the previously added one: # devlink dev reload pci/0000:01:00.0 $ ip neigh show dev gre1 nud noarp 0.0.0.0 lladdr 0.0.0.0 offload NOARP If the neighbor is later deleted, the driver will ignore the notification (given the GRE net device is not its upper) and will therefore keep referencing freed memory, resulting in a use-after-free [1] when the net device is deleted: # ip neigh del 0.0.0.0 lladdr 0.0.0.0 dev gre1 # ip link del dev gre1 Fix by skipping neighbor replay if the net device for which the replay is performed is not our upper. [1] BUG: KASAN: slab-use-after-free in mlxsw_sp_neigh_entry_update+0x1ea/0x200 Read of size 8 at addr ffff888155b0e420 by task ip/2282 [...] Call Trace: <TASK> dump_stack_lvl+0x6f/0xa0 print_address_description.constprop.0+0x6f/0x350 print_report+0x108/0x205 kasan_report+0xdf/0x110 mlxsw_sp_neigh_entry_update+0x1ea/0x200 mlxsw_sp_router_rif_gone_sync+0x2a8/0x440 mlxsw_sp_rif_destroy+0x1e9/0x750 mlxsw_sp_netdevice_ipip_ol_event+0x3c9/0xdc0 mlxsw_sp_router_netdevice_event+0x3ac/0x15e0 notifier_call_chain+0xca/0x150 call_netdevice_notifiers_info+0x7f/0x100 unregister_netdevice_many_notify+0xc8c/0x1d90 rtnl_dellink+0x34e/0xa50 rtnetlink_rcv_msg+0x6fb/0xb70 netlink_rcv_skb+0x131/0x360 netlink_unicast+0x426/0x710 netlink_sendmsg+0x75a/0xc20 __sock_sendmsg+0xc1/0x150 ____sys_sendmsg+0x5aa/0x7b0 ___sys_sendmsg+0xfc/0x180 __sys_sendmsg+0x121/0x1b0 do_syscall_64+0xbb/0x1d0 entry_SYSCALL_64_after_hwframe+0x4b/0x53 Fixes: 8fdb09a7674c ("mlxsw: spectrum_router: Replay neighbours when RIF is made") Signed-off-by: Ido Schimmel <idosch@nvidia.com> Reviewed-by: Petr Machata <petrm@nvidia.com> Signed-off-by: Petr Machata <petrm@nvidia.com> Link: https://patch.msgid.link/c53c02c904fde32dad484657be3b1477884e9ad6.1747225701.git.petrm@nvidia.com Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
2025-05-22octeontx2-pf: Do not reallocate all ntuple filtersSubbaraya Sundeep
[ Upstream commit dcb479fde00be9a151c047d0a7c0626b64eb0019 ] If ntuple filters count is modified followed by unicast filters count using devlink then the ntuple count set by user is ignored and all the ntuple filters are being reallocated. Fix this by storing the ntuple count set by user. Without this patch, say if user tries to modify ntuple count as 8 followed by ucast filter count as 4 using devlink commands then ntuple count is being reverted to default value 16 i.e, not retaining user set value 8. Fixes: 39c469188b6d ("octeontx2-pf: Add ucast filter count configurability via devlink.") Signed-off-by: Subbaraya Sundeep <sbhatta@marvell.com> Reviewed-by: Simon Horman <horms@kernel.org> Link: https://patch.msgid.link/1747054357-5850-1-git-send-email-sbhatta@marvell.com Signed-off-by: Paolo Abeni <pabeni@redhat.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
2025-05-22octeontx2-af: Fix CGX Receive countersHariprasad Kelam
[ Upstream commit bf449f35e77fd44017abf991fac1f9ab7705bbe0 ] Each CGX block supports 4 logical MACs (LMACS). Receive counters CGX_CMR_RX_STAT0-8 are per LMAC and CGX_CMR_RX_STAT9-12 are per CGX. Due a bug in previous patch, stale Per CGX counters values observed. Fixes: 66208910e57a ("octeontx2-af: Support to retrieve CGX LMAC stats") Signed-off-by: Hariprasad Kelam <hkelam@marvell.com> Link: https://patch.msgid.link/20250513071554.728922-1-hkelam@marvell.com Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
2025-05-22net: ethernet: mtk_eth_soc: fix typo for declaration MT7988 ESW capabilityBo-Cun Chen
[ Upstream commit 1bdea6fad6fb985ff13828373c48e337c4e939f9 ] Since MTK_ESW_BIT is a bit number rather than a bitmap, it causes MTK_HAS_CAPS to produce incorrect results. This leads to the ETH driver not declaring MAC capabilities correctly for the MT7988 ESW. Fixes: 445eb6448ed3 ("net: ethernet: mtk_eth_soc: add basic support for MT7988 SoC") Signed-off-by: Bo-Cun Chen <bc-bocun.chen@mediatek.com> Signed-off-by: Daniel Golle <daniel@makrotopia.org> Reviewed-by: Michal Swiatkowski <michal.swiatkowski@linux.intel.com> Link: https://patch.msgid.link/b8b37f409d1280fad9c4d32521e6207f63cd3213.1747110258.git.daniel@makrotopia.org Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
2025-05-22octeontx2-pf: macsec: Fix incorrect max transmit size in TX secySubbaraya Sundeep
[ Upstream commit 865ab2461375e3a5a2526f91f9a9f17b8931bc9e ] MASCEC hardware block has a field called maximum transmit size for TX secy. Max packet size going out of MCS block has be programmed taking into account full packet size which has L2 header,SecTag and ICV. MACSEC offload driver is configuring max transmit size as macsec interface MTU which is incorrect. Say with 1500 MTU of real device, macsec interface created on top of real device will have MTU of 1468(1500 - (SecTag + ICV)). This is causing packets from macsec interface of size greater than or equal to 1468 are not getting transmitted out because driver programmed max transmit size as 1468 instead of 1514(1500 + ETH_HDR_LEN). Fixes: c54ffc73601c ("octeontx2-pf: mcs: Introduce MACSEC hardware offloading") Signed-off-by: Subbaraya Sundeep <sbhatta@marvell.com> Reviewed-by: Simon Horman <horms@kernel.org> Link: https://patch.msgid.link/1747053756-4529-1-git-send-email-sbhatta@marvell.com Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
2025-05-22qlcnic: fix memory leak in qlcnic_sriov_channel_cfg_cmd()Abdun Nihaal
[ Upstream commit 9d8a99c5a7c7f4f7eca2c168a4ec254409670035 ] In one of the error paths in qlcnic_sriov_channel_cfg_cmd(), the memory allocated in qlcnic_sriov_alloc_bc_mbx_args() for mailbox arguments is not freed. Fix that by jumping to the error path that frees them, by calling qlcnic_free_mbx_args(). This was found using static analysis. Fixes: f197a7aa6288 ("qlcnic: VF-PF communication channel implementation") Signed-off-by: Abdun Nihaal <abdun.nihaal@gmail.com> Reviewed-by: Simon Horman <horms@kernel.org> Link: https://patch.msgid.link/20250512044829.36400-1-abdun.nihaal@gmail.com Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
2025-05-22net/mlx5e: Disable MACsec offload for uplink representor profileCarolina Jubran
[ Upstream commit 588431474eb7572e57a927fa8558c9ba2f8af143 ] MACsec offload is not supported in switchdev mode for uplink representors. When switching to the uplink representor profile, the MACsec offload feature must be cleared from the netdevice's features. If left enabled, attempts to add offloads result in a null pointer dereference, as the uplink representor does not support MACsec offload even though the feature bit remains set. Clear NETIF_F_HW_MACSEC in mlx5e_fix_uplink_rep_features(). Kernel log: Oops: general protection fault, probably for non-canonical address 0xdffffc000000000f: 0000 [#1] SMP KASAN KASAN: null-ptr-deref in range [0x0000000000000078-0x000000000000007f] CPU: 29 UID: 0 PID: 4714 Comm: ip Not tainted 6.14.0-rc4_for_upstream_debug_2025_03_02_17_35 #1 Hardware name: QEMU Standard PC (Q35 + ICH9, 2009), BIOS rel-1.16.0-0-gd239552ce722-prebuilt.qemu.org 04/01/2014 RIP: 0010:__mutex_lock+0x128/0x1dd0 Code: d0 7c 08 84 d2 0f 85 ad 15 00 00 8b 35 91 5c fe 03 85 f6 75 29 49 8d 7e 60 48 b8 00 00 00 00 00 fc ff df 48 89 fa 48 c1 ea 03 <80> 3c 02 00 0f 85 a6 15 00 00 4d 3b 76 60 0f 85 fd 0b 00 00 65 ff RSP: 0018:ffff888147a4f160 EFLAGS: 00010206 RAX: dffffc0000000000 RBX: 0000000000000000 RCX: 0000000000000001 RDX: 000000000000000f RSI: 0000000000000000 RDI: 0000000000000078 RBP: ffff888147a4f2e0 R08: ffffffffa05d2c19 R09: 0000000000000000 R10: 0000000000000001 R11: 0000000000000000 R12: 0000000000000000 R13: dffffc0000000000 R14: 0000000000000018 R15: ffff888152de0000 FS: 00007f855e27d800(0000) GS:ffff88881ee80000(0000) knlGS:0000000000000000 CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033 CR2: 00000000004e5768 CR3: 000000013ae7c005 CR4: 0000000000372eb0 DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000 DR3: 0000000000000000 DR6: 00000000fffe07f0 DR7: 0000000000000400 Call Trace: <TASK> ? die_addr+0x3d/0xa0 ? exc_general_protection+0x144/0x220 ? asm_exc_general_protection+0x22/0x30 ? mlx5e_macsec_add_secy+0xf9/0x700 [mlx5_core] ? __mutex_lock+0x128/0x1dd0 ? lockdep_set_lock_cmp_fn+0x190/0x190 ? mlx5e_macsec_add_secy+0xf9/0x700 [mlx5_core] ? mutex_lock_io_nested+0x1ae0/0x1ae0 ? lock_acquire+0x1c2/0x530 ? macsec_upd_offload+0x145/0x380 ? lockdep_hardirqs_on_prepare+0x400/0x400 ? kasan_save_stack+0x30/0x40 ? kasan_save_stack+0x20/0x40 ? kasan_save_track+0x10/0x30 ? __kasan_kmalloc+0x77/0x90 ? __kmalloc_noprof+0x249/0x6b0 ? genl_family_rcv_msg_attrs_parse.constprop.0+0xb5/0x240 ? mlx5e_macsec_add_secy+0xf9/0x700 [mlx5_core] mlx5e_macsec_add_secy+0xf9/0x700 [mlx5_core] ? mlx5e_macsec_add_rxsa+0x11a0/0x11a0 [mlx5_core] macsec_update_offload+0x26c/0x820 ? macsec_set_mac_address+0x4b0/0x4b0 ? lockdep_hardirqs_on_prepare+0x284/0x400 ? _raw_spin_unlock_irqrestore+0x47/0x50 macsec_upd_offload+0x2c8/0x380 ? macsec_update_offload+0x820/0x820 ? __nla_parse+0x22/0x30 ? genl_family_rcv_msg_attrs_parse.constprop.0+0x15e/0x240 genl_family_rcv_msg_doit+0x1cc/0x2a0 ? genl_family_rcv_msg_attrs_parse.constprop.0+0x240/0x240 ? cap_capable+0xd4/0x330 genl_rcv_msg+0x3ea/0x670 ? genl_family_rcv_msg_dumpit+0x2a0/0x2a0 ? lockdep_set_lock_cmp_fn+0x190/0x190 ? macsec_update_offload+0x820/0x820 netlink_rcv_skb+0x12b/0x390 ? genl_family_rcv_msg_dumpit+0x2a0/0x2a0 ? netlink_ack+0xd80/0xd80 ? rwsem_down_read_slowpath+0xf90/0xf90 ? netlink_deliver_tap+0xcd/0xac0 ? netlink_deliver_tap+0x155/0xac0 ? _copy_from_iter+0x1bb/0x12c0 genl_rcv+0x24/0x40 netlink_unicast+0x440/0x700 ? netlink_attachskb+0x760/0x760 ? lock_acquire+0x1c2/0x530 ? __might_fault+0xbb/0x170 netlink_sendmsg+0x749/0xc10 ? netlink_unicast+0x700/0x700 ? __might_fault+0xbb/0x170 ? netlink_unicast+0x700/0x700 __sock_sendmsg+0xc5/0x190 ____sys_sendmsg+0x53f/0x760 ? import_iovec+0x7/0x10 ? kernel_sendmsg+0x30/0x30 ? __copy_msghdr+0x3c0/0x3c0 ? filter_irq_stacks+0x90/0x90 ? stack_depot_save_flags+0x28/0xa30 ___sys_sendmsg+0xeb/0x170 ? kasan_save_stack+0x30/0x40 ? copy_msghdr_from_user+0x110/0x110 ? do_syscall_64+0x6d/0x140 ? lock_acquire+0x1c2/0x530 ? __virt_addr_valid+0x116/0x3b0 ? __virt_addr_valid+0x1da/0x3b0 ? lock_downgrade+0x680/0x680 ? __delete_object+0x21/0x50 __sys_sendmsg+0xf7/0x180 ? __sys_sendmsg_sock+0x20/0x20 ? kmem_cache_free+0x14c/0x4e0 ? __x64_sys_close+0x78/0xd0 do_syscall_64+0x6d/0x140 entry_SYSCALL_64_after_hwframe+0x4b/0x53 RIP: 0033:0x7f855e113367 Code: 0e 00 f7 d8 64 89 02 48 c7 c0 ff ff ff ff eb b9 0f 1f 00 f3 0f 1e fa 64 8b 04 25 18 00 00 00 85 c0 75 10 b8 2e 00 00 00 0f 05 <48> 3d 00 f0 ff ff 77 51 c3 48 83 ec 28 89 54 24 1c 48 89 74 24 10 RSP: 002b:00007ffd15e90c88 EFLAGS: 00000246 ORIG_RAX: 000000000000002e RAX: ffffffffffffffda RBX: 0000000000000002 RCX: 00007f855e113367 RDX: 0000000000000000 RSI: 00007ffd15e90cf0 RDI: 0000000000000004 RBP: 00007ffd15e90dbc R08: 0000000000000028 R09: 000000000045d100 R10: 00007f855e011dd8 R11: 0000000000000246 R12: 0000000000000019 R13: 0000000067c6b785 R14: 00000000004a1e80 R15: 0000000000000000 </TASK> Modules linked in: 8021q garp mrp sch_ingress openvswitch nsh mlx5_ib mlx5_fwctl mlx5_dpll mlx5_core rpcrdma rdma_ucm ib_iser libiscsi scsi_transport_iscsi ib_umad rdma_cm ib_ipoib iw_cm ib_cm ib_uverbs ib_core xt_conntrack xt_MASQUERADE nf_conntrack_netlink nfnetlink xt_addrtype iptable_nat nf_nat br_netfilter rpcsec_gss_krb5 auth_rpcgss oid_registry overlay zram zsmalloc fuse [last unloaded: mlx5_core] ---[ end trace 0000000000000000 ]--- Fixes: 8ff0ac5be144 ("net/mlx5: Add MACsec offload Tx command support") Signed-off-by: Carolina Jubran <cjubran@nvidia.com> Reviewed-by: Shahar Shitrit <shshitrit@nvidia.com> Reviewed-by: Dragos Tatulea <dtatulea@nvidia.com> Signed-off-by: Tariq Toukan <tariqt@nvidia.com> Reviewed-by: Simon Horman <horms@kernel.org> Link: https://patch.msgid.link/1746958552-561295-1-git-send-email-tariqt@nvidia.com Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
2025-05-22net: dsa: b53: prevent standalone from trying to forward to other portsJonas Gorski
[ Upstream commit 4227ea91e2657f7965e34313448e9d0a2b67712e ] When bridged ports and standalone ports share a VLAN, e.g. via VLAN uppers, or untagged traffic with a vlan unaware bridge, the ASIC will still try to forward traffic to known FDB entries on standalone ports. But since the port VLAN masks prevent forwarding to bridged ports, this traffic will be dropped. This e.g. can be observed in the bridge_vlan_unaware ping tests, where this breaks pinging with learning on. Work around this by enabling the simplified EAP mode on switches supporting it for standalone ports, which causes the ASIC to redirect traffic of unknown source MAC addresses to the CPU port. Since standalone ports do not learn, there are no known source MAC addresses, so effectively this redirects all incoming traffic to the CPU port. Fixes: ff39c2d68679 ("net: dsa: b53: Add bridge support") Signed-off-by: Jonas Gorski <jonas.gorski@gmail.com> Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com> Reviewed-by: Vladimir Oltean <olteanv@gmail.com> Link: https://patch.msgid.link/20250508091424.26870-1-jonas.gorski@gmail.com Signed-off-by: Paolo Abeni <pabeni@redhat.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
2025-05-22net: dsa: sja1105: discard incoming frames in BR_STATE_LISTENINGVladimir Oltean
[ Upstream commit 498625a8ab2c8e1c9ab5105744310e8d6952cc01 ] It has been reported that when under a bridge with stp_state=1, the logs get spammed with this message: [ 251.734607] fsl_dpaa2_eth dpni.5 eth0: Couldn't decode source port Further debugging shows the following info associated with packets: source_port=-1, switch_id=-1, vid=-1, vbid=1 In other words, they are data plane packets which are supposed to be decoded by dsa_tag_8021q_find_port_by_vbid(), but the latter (correctly) refuses to do so, because no switch port is currently in BR_STATE_LEARNING or BR_STATE_FORWARDING - so the packet is effectively unexpected. The error goes away after the port progresses to BR_STATE_LEARNING in 15 seconds (the default forward_time of the bridge), because then, dsa_tag_8021q_find_port_by_vbid() can correctly associate the data plane packets with a plausible bridge port in a plausible STP state. Re-reading IEEE 802.1D-1990, I see the following: "4.4.2 Learning: (...) The Forwarding Process shall discard received frames." IEEE 802.1D-2004 further clarifies: "DISABLED, BLOCKING, LISTENING, and BROKEN all correspond to the DISCARDING port state. While those dot1dStpPortStates serve to distinguish reasons for discarding frames, the operation of the Forwarding and Learning processes is the same for all of them. (...) LISTENING represents a port that the spanning tree algorithm has selected to be part of the active topology (computing a Root Port or Designated Port role) but is temporarily discarding frames to guard against loops or incorrect learning." Well, this is not what the driver does - instead it sets mac[port].ingress = true. To get rid of the log spam, prevent unexpected data plane packets to be received by software by discarding them on ingress in the LISTENING state. In terms of blame attribution: the prints only date back to commit d7f9787a763f ("net: dsa: tag_8021q: add support for imprecise RX based on the VBID"). However, the settings would permit a LISTENING port to forward to a FORWARDING port, and the standard suggests that's not OK. Fixes: 640f763f98c2 ("net: dsa: sja1105: Add support for Spanning Tree Protocol") Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com> Link: https://patch.msgid.link/20250509113816.2221992-1-vladimir.oltean@nxp.com Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
2025-05-22net: cadence: macb: Fix a possible deadlock in macb_halt_tx.Mathieu Othacehe
[ Upstream commit c92d6089d8ad7d4d815ebcedee3f3907b539ff1f ] There is a situation where after THALT is set high, TGO stays high as well. Because jiffies are never updated, as we are in a context with interrupts disabled, we never exit that loop and have a deadlock. That deadlock was noticed on a sama5d4 device that stayed locked for days. Use retries instead of jiffies so that the timeout really works and we do not have a deadlock anymore. Fixes: e86cd53afc590 ("net/macb: better manage tx errors") Signed-off-by: Mathieu Othacehe <othacehe@gnu.org> Reviewed-by: Simon Horman <horms@kernel.org> Link: https://patch.msgid.link/20250509121935.16282-1-othacehe@gnu.org Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
2025-05-22virtio_net: ensure netdev_tx_reset_queue is called on bind xsk for txKoichiro Den
[ Upstream commit 76a771ec4c9adfd75fe53c8505cf656a075d7101 ] virtnet_sq_bind_xsk_pool() flushes tx skbs and then resets tx queue, so DQL counters need to be reset when flushing has actually occurred, Add virtnet_sq_free_unused_buf_done() as a callback for virtqueue_resize() to handle this. Fixes: 21a4e3ce6dc7 ("virtio_net: xsk: bind/unbind xsk for tx") Signed-off-by: Koichiro Den <koichiro.den@canonical.com> Acked-by: Jason Wang <jasowang@redhat.com> Reviewed-by: Xuan Zhuo <xuanzhuo@linux.alibaba.com> Signed-off-by: Paolo Abeni <pabeni@redhat.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
2025-05-22virtio_ring: add a func argument 'recycle_done' to virtqueue_reset()Koichiro Den
[ Upstream commit 8d2da07c813ad333c20eb803e15f8c4541f25350 ] When virtqueue_reset() has actually recycled all unused buffers, additional work may be required in some cases. Relying solely on its return status is fragile, so introduce a new function argument 'recycle_done', which is invoked when it really occurs. Signed-off-by: Koichiro Den <koichiro.den@canonical.com> Acked-by: Jason Wang <jasowang@redhat.com> Reviewed-by: Xuan Zhuo <xuanzhuo@linux.alibaba.com> Signed-off-by: Paolo Abeni <pabeni@redhat.com> Stable-dep-of: 76a771ec4c9a ("virtio_net: ensure netdev_tx_reset_queue is called on bind xsk for tx") Signed-off-by: Sasha Levin <sashal@kernel.org>
2025-05-18virtio-net: fix total qstat valuesJakub Kicinski
[ Upstream commit 001160ec8c59115efc39e197d40829bdafd4d7f5 ] NIPA tests report that the interface statistics reported via qstat are lower than those reported via ip link. Looks like this is because some tests flip the queue count up and down, and we end up with some of the traffic accounted on disabled queues. Add up counters from disabled queues. Fixes: d888f04c09bb ("virtio-net: support queue stat") Signed-off-by: Jakub Kicinski <kuba@kernel.org> Link: https://patch.msgid.link/20250507003221.823267-3-kuba@kernel.org Signed-off-by: Paolo Abeni <pabeni@redhat.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
2025-05-18fbnic: Do not allow mailbox to toggle to ready outside fbnic_mbx_poll_tx_readyAlexander Duyck
[ Upstream commit ce2fa1dba204c761582674cf2eb9cbe0b949b5c7 ] We had originally thought to have the mailbox go to ready in the background while we were doing other things. One issue with this though is that we can't disable it by clearing the ready state without also blocking interrupts or calls to mbx_poll as it will just pop back to life during an interrupt. In order to prevent that from happening we can pull the code for toggling to ready out of the interrupt path and instead place it in the fbnic_mbx_poll_tx_ready path so that it becomes the only spot where the Rx/Tx can toggle to the ready state. By doing this we can prevent races where we disable the DMA and/or free buffers only to have an interrupt fire and undo what we have done. Fixes: da3cde08209e ("eth: fbnic: Add FW communication mechanism") Signed-off-by: Alexander Duyck <alexanderduyck@fb.com> Reviewed-by: Jacob Keller <jacob.e.keller@intel.com> Link: https://patch.msgid.link/174654722518.499179.11612865740376848478.stgit@ahduyck-xeon-server.home.arpa Reviewed-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Paolo Abeni <pabeni@redhat.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
2025-05-18fbnic: Pull fbnic_fw_xmit_cap_msg use out of interrupt contextAlexander Duyck
[ Upstream commit 1b34d1c1dc8384884febd83140c9afbc7c4b9eb8 ] This change pulls the call to fbnic_fw_xmit_cap_msg out of fbnic_mbx_init_desc_ring and instead places it in the polling function for getting the Tx ready. Doing that we can avoid the potential issue with an interrupt coming in later from the firmware that causes it to get fired in interrupt context. Fixes: 20d2e88cc746 ("eth: fbnic: Add initial messaging to notify FW of our presence") Signed-off-by: Alexander Duyck <alexanderduyck@fb.com> Reviewed-by: Jacob Keller <jacob.e.keller@intel.com> Link: https://patch.msgid.link/174654721876.499179.9839651602256668493.stgit@ahduyck-xeon-server.home.arpa Reviewed-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Paolo Abeni <pabeni@redhat.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
2025-05-18fbnic: Improve responsiveness of fbnic_mbx_poll_tx_readyAlexander Duyck
[ Upstream commit ab064f6005973d456f95ae99cd9ea0d8ab676cce ] There were a couple different issues found in fbnic_mbx_poll_tx_ready. Among them were the fact that we were sleeping much longer than we actually needed to as the actual FW could respond in under 20ms. The other issue was that we would just keep polling the mailbox even if the device itself had gone away. To address the responsiveness issues we can decrease the sleeps to 20ms and use a jiffies based timeout value rather than just counting the number of times we slept and then polled. To address the hardware going away we can move the check for the firmware BAR being present from where it was and place it inside the loop after the mailbox descriptor ring is initialized and before we sleep so that we just abort and return an error if the device went away during initialization. With these two changes we see a significant improvement in boot times for the driver. Fixes: da3cde08209e ("eth: fbnic: Add FW communication mechanism") Signed-off-by: Alexander Duyck <alexanderduyck@fb.com> Reviewed-by: Jacob Keller <jacob.e.keller@intel.com> Link: https://patch.msgid.link/174654721224.499179.2698616208976624755.stgit@ahduyck-xeon-server.home.arpa Reviewed-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Paolo Abeni <pabeni@redhat.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
2025-05-18fbnic: Actually flush_tx instead of stalling outAlexander Duyck
[ Upstream commit 0f9a959a0addd9bbc47e5d16c36b3a7f97981915 ] The fbnic_mbx_flush_tx function had a number of issues. First, we were waiting 200ms for the firmware to process the packets. We can drop this to 20ms and in almost all cases this should be more than enough time. So by changing this we can significantly reduce shutdown time. Second, we were not making sure that the Tx path was actually shut off. As such we could still have packets added while we were flushing the mailbox. To prevent that we can now clear the ready flag for the Tx side and it should stay down since the interrupt is disabled. Third, we kept re-reading the tail due to the second issue. The tail should not move after we have started the flush so we can just read it once while we are holding the mailbox Tx lock. By doing that we are guaranteed that the value should be consistent. Fourth, we were keeping a count of descriptors cleaned due to the second and third issues called out. That count is not a valid reason to be exiting the cleanup, and with the tail only being read once we shouldn't see any cases where the tail moves after the disable so the tracking of count can be dropped. Fifth, we were using attempts * sleep time to determine how long we would wait in our polling loop to flush out the Tx. This can be very imprecise. In order to tighten up the timing we are shifting over to using a jiffies value of jiffies + 10 * HZ + 1 to determine the jiffies value we should stop polling at as this should be accurate within once sleep cycle for the total amount of time spent polling. Fixes: da3cde08209e ("eth: fbnic: Add FW communication mechanism") Signed-off-by: Alexander Duyck <alexanderduyck@fb.com> Reviewed-by: Simon Horman <horms@kernel.org> Reviewed-by: Jacob Keller <jacob.e.keller@intel.com> Link: https://patch.msgid.link/174654719929.499179.16406653096197423749.stgit@ahduyck-xeon-server.home.arpa Reviewed-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Paolo Abeni <pabeni@redhat.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
2025-05-18fbnic: Gate AXI read/write enabling on FW mailboxAlexander Duyck
[ Upstream commit 3b12f00ddd08e888273b2ac0488d396d90a836fc ] In order to prevent the device from throwing spurious writes and/or reads at us we need to gate the AXI fabric interface to the PCIe until such time as we know the FW is in a known good state. To accomplish this we use the mailbox as a mechanism for us to recognize that the FW has acknowledged our presence and is no longer sending any stale message data to us. We start in fbnic_mbx_init by calling fbnic_mbx_reset_desc_ring function, disabling the DMA in both directions, and then invalidating all the descriptors in each ring. We then poll the mailbox in fbnic_mbx_poll_tx_ready and when the interrupt is set by the FW we pick it up and mark the mailboxes as ready, while also enabling the DMA. Once we have completed all the transactions and need to shut down we call into fbnic_mbx_clean which will in turn call fbnic_mbx_reset_desc_ring for each ring and shut down the DMA and once again invalidate the descriptors. Fixes: 3646153161f1 ("eth: fbnic: Add register init to set PCIe/Ethernet device config") Fixes: da3cde08209e ("eth: fbnic: Add FW communication mechanism") Signed-off-by: Alexander Duyck <alexanderduyck@fb.com> Reviewed-by: Simon Horman <horms@kernel.org> Reviewed-by: Jacob Keller <jacob.e.keller@intel.com> Link: https://patch.msgid.link/174654718623.499179.7445197308109347982.stgit@ahduyck-xeon-server.home.arpa Reviewed-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Paolo Abeni <pabeni@redhat.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
2025-05-18fbnic: Fix initialization of mailbox descriptor ringsAlexander Duyck
[ Upstream commit f34343cc11afc7bb1f881c3492bee3484016bf71 ] Address to issues with the FW mailbox descriptor initialization. We need to reverse the order of accesses when we invalidate an entry versus writing an entry. When writing an entry we write upper and then lower as the lower 32b contain the valid bit that makes the entire address valid. However for invalidation we should write it in the reverse order so that the upper is marked invalid before we update it. Without this change we may see FW attempt to access pages with the upper 32b of the address set to 0 which will likely result in DMAR faults due to write access failures on mailbox shutdown. Fixes: da3cde08209e ("eth: fbnic: Add FW communication mechanism") Signed-off-by: Alexander Duyck <alexanderduyck@fb.com> Reviewed-by: Simon Horman <horms@kernel.org> Reviewed-by: Jacob Keller <jacob.e.keller@intel.com> Link: https://patch.msgid.link/174654717972.499179.8083789731819297034.stgit@ahduyck-xeon-server.home.arpa Reviewed-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Paolo Abeni <pabeni@redhat.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
2025-05-18net: dsa: b53: do not set learning and unicast/multicast on upJonas Gorski
[ Upstream commit 2e7179c628d3cb9aee75e412473813b099e11ed4 ] When a port gets set up, b53 disables learning and enables the port for flooding. This can undo any bridge configuration on the port. E.g. the following flow would disable learning on a port: $ ip link add br0 type bridge $ ip link set sw1p1 master br0 <- enables learning for sw1p1 $ ip link set br0 up $ ip link set sw1p1 up <- disables learning again Fix this by populating dsa_switch_ops::port_setup(), and set up initial config there. Fixes: f9b3827ee66c ("net: dsa: b53: Support setting learning on port") Signed-off-by: Jonas Gorski <jonas.gorski@gmail.com> Tested-by: Florian Fainelli <florian.fainelli@broadcom.com> Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com> Link: https://patch.msgid.link/20250429201710.330937-12-jonas.gorski@gmail.com Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
2025-05-18net: dsa: b53: fix learning on VLAN unaware bridgesJonas Gorski
[ Upstream commit 9f34ad89bcf0e6df6f8b01f1bdab211493fc66d1 ] When VLAN filtering is off, we configure the switch to forward, but not learn on VLAN table misses. This effectively disables learning while not filtering. Fix this by switching to forward and learn. Setting the learning disable register will still control whether learning actually happens. Fixes: dad8d7c6452b ("net: dsa: b53: Properly account for VLAN filtering") Signed-off-by: Jonas Gorski <jonas.gorski@gmail.com> Tested-by: Florian Fainelli <florian.fainelli@broadcom.com> Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com> Link: https://patch.msgid.link/20250429201710.330937-11-jonas.gorski@gmail.com Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
2025-05-18net: dsa: b53: fix toggling vlan_filteringJonas Gorski
[ Upstream commit 2dc2bd57111582895e10f54ea380329c89873f1c ] To allow runtime switching between vlan aware and vlan non-aware mode, we need to properly keep track of any bridge VLAN configuration. Likewise, we need to know when we actually switch between both modes, to not have to rewrite the full VLAN table every time we update the VLANs. So keep track of the current vlan_filtering mode, and on changes, apply the appropriate VLAN configuration. Fixes: 0ee2af4ebbe3 ("net: dsa: set configure_vlan_while_not_filtering to true by default") Signed-off-by: Jonas Gorski <jonas.gorski@gmail.com> Tested-by: Florian Fainelli <florian.fainelli@broadcom.com> Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com> Link: https://patch.msgid.link/20250429201710.330937-10-jonas.gorski@gmail.com Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
2025-05-18net: dsa: b53: do not program vlans when vlan filtering is offJonas Gorski
[ Upstream commit f089652b6b16452535dcc5cbaa6e2bb05acd3f93 ] Documentation/networking/switchdev.rst says: - with VLAN filtering turned off: the bridge is strictly VLAN unaware and its data path will process all Ethernet frames as if they are VLAN-untagged. The bridge VLAN database can still be modified, but the modifications should have no effect while VLAN filtering is turned off. This breaks if we immediately apply the VLAN configuration, so skip writing it when vlan_filtering is off. Fixes: 0ee2af4ebbe3 ("net: dsa: set configure_vlan_while_not_filtering to true by default") Signed-off-by: Jonas Gorski <jonas.gorski@gmail.com> Tested-by: Florian Fainelli <florian.fainelli@broadcom.com> Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com> Link: https://patch.msgid.link/20250429201710.330937-9-jonas.gorski@gmail.com Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
2025-05-18net: dsa: b53: do not allow to configure VLAN 0Jonas Gorski
[ Upstream commit 45e9d59d39503bb3e6ab4d258caea4ba6496e2dc ] Since we cannot set forwarding destinations per VLAN, we should not have a VLAN 0 configured, as it would allow untagged traffic to work across ports on VLAN aware bridges regardless if a PVID untagged VLAN exists. So remove the VLAN 0 on join, an re-add it on leave. But only do so if we have a VLAN aware bridge, as without it, untagged traffic would become tagged with VID 0 on a VLAN unaware bridge. Fixes: a2482d2ce349 ("net: dsa: b53: Plug in VLAN support") Signed-off-by: Jonas Gorski <jonas.gorski@gmail.com> Tested-by: Florian Fainelli <florian.fainelli@broadcom.com> Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com> Link: https://patch.msgid.link/20250429201710.330937-8-jonas.gorski@gmail.com Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
2025-05-18net: dsa: b53: always rejoin default untagged VLAN on bridge leaveJonas Gorski
[ Upstream commit 13b152ae40495966501697693f048f47430c50fd ] While JOIN_ALL_VLAN allows to join all VLANs, we still need to keep the default VLAN enabled so that untagged traffic stays untagged. So rejoin the default VLAN even for switches with JOIN_ALL_VLAN support. Fixes: 48aea33a77ab ("net: dsa: b53: Add JOIN_ALL_VLAN support") Signed-off-by: Jonas Gorski <jonas.gorski@gmail.com> Tested-by: Florian Fainelli <florian.fainelli@broadcom.com> Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com> Link: https://patch.msgid.link/20250429201710.330937-7-jonas.gorski@gmail.com Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
2025-05-18net: dsa: b53: fix VLAN ID for untagged vlan on bridge leaveJonas Gorski
[ Upstream commit a1c1901c5cc881425cc45992ab6c5418174e9e5a ] The untagged default VLAN is added to the default vlan, which may be one, but we modify the VLAN 0 entry on bridge leave. Fix this to use the correct VLAN entry for the default pvid. Fixes: fea83353177a ("net: dsa: b53: Fix default VLAN ID") Signed-off-by: Jonas Gorski <jonas.gorski@gmail.com> Tested-by: Florian Fainelli <florian.fainelli@broadcom.com> Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com> Link: https://patch.msgid.link/20250429201710.330937-6-jonas.gorski@gmail.com Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
2025-05-18net: dsa: b53: fix flushing old pvid VLAN on pvid changeJonas Gorski
[ Upstream commit 083c6b28c0cbcd83b6af1a10f2c82937129b3438 ] Presumably the intention here was to flush the VLAN of the old pvid, not the added VLAN again, which we already flushed before. Fixes: a2482d2ce349 ("net: dsa: b53: Plug in VLAN support") Signed-off-by: Jonas Gorski <jonas.gorski@gmail.com> Tested-by: Florian Fainelli <florian.fainelli@broadcom.com> Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com> Link: https://patch.msgid.link/20250429201710.330937-5-jonas.gorski@gmail.com Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
2025-05-18net: dsa: b53: fix clearing PVID of a portJonas Gorski
[ Upstream commit f480851981043d9bb6447ca9883ade9247b9a0ad ] Currently the PVID of ports are only set when adding/updating VLANs with PVID set or removing VLANs, but not when clearing the PVID flag of a VLAN. E.g. the following flow $ ip link add br0 type bridge vlan_filtering 1 $ ip link set sw1p1 master bridge $ bridge vlan add dev sw1p1 vid 10 pvid untagged $ bridge vlan add dev sw1p1 vid 10 untagged Would keep the PVID set as 10, despite the flag being cleared. Fix this by checking if we need to unset the PVID on vlan updates. Fixes: a2482d2ce349 ("net: dsa: b53: Plug in VLAN support") Signed-off-by: Jonas Gorski <jonas.gorski@gmail.com> Tested-by: Florian Fainelli <florian.fainelli@broadcom.com> Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com> Link: https://patch.msgid.link/20250429201710.330937-4-jonas.gorski@gmail.com Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
2025-05-18net: dsa: b53: keep CPU port always tagged againJonas Gorski
[ Upstream commit 425f11d4cc9bd9e97e6825d9abb2c51a068ca7b5 ] The Broadcom management header does not carry the original VLAN tag state information, just the ingress port, so for untagged frames we do not know from which VLAN they originated. Therefore keep the CPU port always tagged except for VLAN 0. Fixes the following setup: $ ip link add br0 type bridge vlan_filtering 1 $ ip link set sw1p1 master br0 $ bridge vlan add dev br0 pvid untagged self $ ip link add sw1p2.10 link sw1p2 type vlan id 10 Where VID 10 would stay untagged on the CPU port. Fixes: 2c32a3d3c233 ("net: dsa: b53: Do not force CPU to be always tagged") Signed-off-by: Jonas Gorski <jonas.gorski@gmail.com> Tested-by: Florian Fainelli <florian.fainelli@broadcom.com> Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com> Link: https://patch.msgid.link/20250429201710.330937-3-jonas.gorski@gmail.com Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
2025-05-18net: dsa: b53: allow leaky reserved multicastJonas Gorski
[ Upstream commit 5f93185a757ff38b36f849c659aeef368db15a68 ] Allow reserved multicast to ignore VLAN membership so STP and other management protocols work without a PVID VLAN configured when using a vlan aware bridge. Fixes: 967dd82ffc52 ("net: dsa: b53: Add support for Broadcom RoboSwitch") Signed-off-by: Jonas Gorski <jonas.gorski@gmail.com> Tested-by: Florian Fainelli <florian.fainelli@broadcom.com> Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com> Link: https://patch.msgid.link/20250429201710.330937-2-jonas.gorski@gmail.com Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
2025-05-18ice: use DSN instead of PCI BDF for ice_adapter indexPrzemek Kitszel
[ Upstream commit 0093cb194a7511d1e68865fa35b763c72e44c2f0 ] Use Device Serial Number instead of PCI bus/device/function for the index of struct ice_adapter. Functions on the same physical device should point to the very same ice_adapter instance, but with two PFs, when at least one of them is PCI-e passed-through to a VM, it is no longer the case - PFs will get seemingly random PCI BDF values, and thus indices, what finally leds to each of them being on their own instance of ice_adapter. That causes them to don't attempt any synchronization of the PTP HW clock usage, or any other future resources. DSN works nicely in place of the index, as it is "immutable" in terms of virtualization. Fixes: 0e2bddf9e5f9 ("ice: add ice_adapter for shared data across PFs on the same NIC") Suggested-by: Jacob Keller <jacob.e.keller@intel.com> Suggested-by: Jakub Kicinski <kuba@kernel.org> Suggested-by: Jiri Pirko <jiri@resnulli.us> Reviewed-by: Aleksandr Loktionov <aleksandr.loktionov@intel.com> Signed-off-by: Przemek Kitszel <przemyslaw.kitszel@intel.com> Reviewed-by: Simon Horman <horms@kernel.org> Tested-by: Rinitha S <sx.rinitha@intel.com> (A Contingent worker at Intel) Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com> Reviewed-by: Jiri Pirko <jiri@nvidia.com> Link: https://patch.msgid.link/20250505161939.2083581-1-anthony.l.nguyen@intel.com Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
2025-05-18ice: Initial support for E825C hardware in ice_adapterSergey Temerkhanov
[ Upstream commit fdb7f54700b1c88e734323a62fea986d9ce5a9c6 ] Address E825C devices by PCI ID since dual IP core configurations need 1 ice_adapter for both devices. Signed-off-by: Sergey Temerkhanov <sergey.temerkhanov@intel.com> Reviewed-by: Simon Horman <horms@kernel.org> Tested-by: Pucha Himasekhar Reddy <himasekharx.reddy.pucha@intel.com> (A Contingent worker at Intel) Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com> Stable-dep-of: 0093cb194a75 ("ice: use DSN instead of PCI BDF for ice_adapter index") Signed-off-by: Sasha Levin <sashal@kernel.org>
2025-05-18can: mcp251xfd: fix TDC setting for low data bit ratesKelsey Maes
[ Upstream commit 5e1663810e11c64956aa7e280cf74b2f3284d816 ] The TDC is currently hardcoded enabled. This means that even for lower CAN-FD data bitrates (with a DBRP (data bitrate prescaler) > 2) a TDC is configured. This leads to a bus-off condition. ISO 11898-1 section 11.3.3 says "Transmitter delay compensation" (TDC) is only applicable if DBRP is 1 or 2. To fix the problem, switch the driver to use the TDC calculation provided by the CAN driver framework (which respects ISO 11898-1 section 11.3.3). This has the positive side effect that userspace can control TDC as needed. Demonstration of the feature in action: | $ ip link set can0 up type can bitrate 125000 dbitrate 500000 fd on | $ ip -details link show can0 | 3: can0: <NOARP,UP,LOWER_UP,ECHO> mtu 72 qdisc pfifo_fast state UP mode DEFAULT group default qlen 10 | link/can promiscuity 0 allmulti 0 minmtu 0 maxmtu 0 | can <FD> state ERROR-ACTIVE (berr-counter tx 0 rx 0) restart-ms 0 | bitrate 125000 sample-point 0.875 | tq 50 prop-seg 69 phase-seg1 70 phase-seg2 20 sjw 10 brp 2 | mcp251xfd: tseg1 2..256 tseg2 1..128 sjw 1..128 brp 1..256 brp_inc 1 | dbitrate 500000 dsample-point 0.875 | dtq 125 dprop-seg 6 dphase-seg1 7 dphase-seg2 2 dsjw 1 dbrp 5 | mcp251xfd: dtseg1 1..32 dtseg2 1..16 dsjw 1..16 dbrp 1..256 dbrp_inc 1 | tdcv 0..63 tdco 0..63 | clock 40000000 numtxqueues 1 numrxqueues 1 gso_max_size 65536 gso_max_segs 65535 tso_max_size 65536 tso_max_segs 65535 gro_max_size 65536 parentbus spi parentdev spi0.0 | $ ip link set can0 up type can bitrate 1000000 dbitrate 4000000 fd on | $ ip -details link show can0 | 3: can0: <NOARP,UP,LOWER_UP,ECHO> mtu 72 qdisc pfifo_fast state UP mode DEFAULT group default qlen 10 | link/can promiscuity 0 allmulti 0 minmtu 0 maxmtu 0 | can <FD,TDC-AUTO> state ERROR-ACTIVE (berr-counter tx 0 rx 0) restart-ms 0 | bitrate 1000000 sample-point 0.750 | tq 25 prop-seg 14 phase-seg1 15 phase-seg2 10 sjw 5 brp 1 | mcp251xfd: tseg1 2..256 tseg2 1..128 sjw 1..128 brp 1..256 brp_inc 1 | dbitrate 4000000 dsample-point 0.700 | dtq 25 dprop-seg 3 dphase-seg1 3 dphase-seg2 3 dsjw 1 dbrp 1 | tdco 7 | mcp251xfd: dtseg1 1..32 dtseg2 1..16 dsjw 1..16 dbrp 1..256 dbrp_inc 1 | tdcv 0..63 tdco 0..63 | clock 40000000 numtxqueues 1 numrxqueues 1 gso_max_size 65536 gso_max_segs 65535 tso_max_size 65536 tso_max_segs 65535 gro_max_size 65536 parentbus spi parentdev spi0.0 There has been some confusion about the MCP2518FD using a relative or absolute TDCO due to the datasheet specifying a range of [-64,63]. I have a custom board with a 40 MHz clock and an estimated loop delay of 100 to 216 ns. During testing at a data bit rate of 4 Mbit/s I found that using can_get_relative_tdco() resulted in bus-off errors. The final TDCO value was 1 which corresponds to a 10% SSP in an absolute configuration. This behavior is expected if the TDCO value is really absolute and not relative. Using priv->can.tdc.tdco instead results in a final TDCO of 8, setting the SSP at exactly 80%. This configuration works. The automatic, manual, and off TDC modes were tested at speeds up to, and including, 8 Mbit/s on real hardware and behave as expected. Fixes: 55e5b97f003e ("can: mcp25xxfd: add driver for Microchip MCP25xxFD SPI CAN") Reported-by: Kelsey Maes <kelsey@vpprocess.com> Closes: https://lore.kernel.org/all/C2121586-C87F-4B23-A933-845362C29CA1@vpprocess.com Reviewed-by: Vincent Mailhol <mailhol.vincent@wanadoo.fr> Signed-off-by: Kelsey Maes <kelsey@vpprocess.com> Link: https://patch.msgid.link/20250430161501.79370-1-kelsey@vpprocess.com [mkl: add comment] Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de> Signed-off-by: Sasha Levin <sashal@kernel.org>
2025-05-18can: m_can: m_can_class_allocate_dev(): initialize spin lock on device probeAntonios Salios
[ Upstream commit dcaeeb8ae84c5506ebc574732838264f3887738c ] The spin lock tx_handling_spinlock in struct m_can_classdev is not being initialized. This leads the following spinlock bad magic complaint from the kernel, eg. when trying to send CAN frames with cansend from can-utils: | BUG: spinlock bad magic on CPU#0, cansend/95 | lock: 0xff60000002ec1010, .magic: 00000000, .owner: <none>/-1, .owner_cpu: 0 | CPU: 0 UID: 0 PID: 95 Comm: cansend Not tainted 6.15.0-rc3-00032-ga79be02bba5c #5 NONE | Hardware name: MachineWare SIM-V (DT) | Call Trace: | [<ffffffff800133e0>] dump_backtrace+0x1c/0x24 | [<ffffffff800022f2>] show_stack+0x28/0x34 | [<ffffffff8000de3e>] dump_stack_lvl+0x4a/0x68 | [<ffffffff8000de70>] dump_stack+0x14/0x1c | [<ffffffff80003134>] spin_dump+0x62/0x6e | [<ffffffff800883ba>] do_raw_spin_lock+0xd0/0x142 | [<ffffffff807a6fcc>] _raw_spin_lock_irqsave+0x20/0x2c | [<ffffffff80536dba>] m_can_start_xmit+0x90/0x34a | [<ffffffff806148b0>] dev_hard_start_xmit+0xa6/0xee | [<ffffffff8065b730>] sch_direct_xmit+0x114/0x292 | [<ffffffff80614e2a>] __dev_queue_xmit+0x3b0/0xaa8 | [<ffffffff8073b8fa>] can_send+0xc6/0x242 | [<ffffffff8073d1c0>] raw_sendmsg+0x1a8/0x36c | [<ffffffff805ebf06>] sock_write_iter+0x9a/0xee | [<ffffffff801d06ea>] vfs_write+0x184/0x3a6 | [<ffffffff801d0a88>] ksys_write+0xa0/0xc0 | [<ffffffff801d0abc>] __riscv_sys_write+0x14/0x1c | [<ffffffff8079ebf8>] do_trap_ecall_u+0x168/0x212 | [<ffffffff807a830a>] handle_exception+0x146/0x152 Initializing the spin lock in m_can_class_allocate_dev solves that problem. Fixes: 1fa80e23c150 ("can: m_can: Introduce a tx_fifo_in_flight counter") Signed-off-by: Antonios Salios <antonios@mwa.re> Reviewed-by: Vincent Mailhol <mailhol.vincent@wanadoo.fr> Link: https://patch.msgid.link/20250425111744.37604-2-antonios@mwa.re Reviewed-by: Markus Schneider-Pargmann <msp@baylibre.com> Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de> Signed-off-by: Sasha Levin <sashal@kernel.org>
2025-05-18net: ethernet: mtk_eth_soc: do not reset PSE when setting FEFrank Wunderlich
[ Upstream commit e8716b5b0dff1b3d523b4a83fd5e94d57b887c5c ] Remove redundant PSE reset. When setting FE register there is no need to reset PSE, doing so may cause FE to work abnormal. Link: https://git01.mediatek.com/plugins/gitiles/openwrt/feeds/mtk-openwrt-feeds/+/3a5223473e086a4b54a2b9a44df7d9ddcc2bc75a Fixes: dee4dd10c79aa ("net: ethernet: mtk_eth_soc: ppe: add support for multiple PPEs") Signed-off-by: Frank Wunderlich <frank-w@public-files.de> Link: https://patch.msgid.link/18f0ac7d83f82defa3342c11ef0d1362f6b81e88.1746406763.git.daniel@makrotopia.org Signed-off-by: Paolo Abeni <pabeni@redhat.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
2025-05-18net: ethernet: mtk_eth_soc: reset all TX queues on DMA freeDaniel Golle
[ Upstream commit 4db6c75124d871fbabf8243f947d34cc7e0697fc ] The purpose of resetting the TX queue is to reset the byte and packet count as well as to clear the software flow control XOFF bit. MediaTek developers pointed out that netdev_reset_queue would only resets queue 0 of the network device. Queues that are not reset may cause unexpected issues. Packets may stop being sent after reset and "transmit timeout" log may be displayed. Import fix from MediaTek's SDK to resolve this issue. Link: https://git01.mediatek.com/plugins/gitiles/openwrt/feeds/mtk-openwrt-feeds/+/319c0d9905579a46dc448579f892f364f1f84818 Fixes: f63959c7eec31 ("net: ethernet: mtk_eth_soc: implement multi-queue support for per-port queues") Signed-off-by: Daniel Golle <daniel@makrotopia.org> Link: https://patch.msgid.link/c9ff9adceac4f152239a0f65c397f13547639175.1746406763.git.daniel@makrotopia.org Signed-off-by: Paolo Abeni <pabeni@redhat.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
2025-05-18virtio-net: free xsk_buffs on error in virtnet_xsk_pool_enable()Jakub Kicinski
[ Upstream commit 4397684a292a71fbc1e815c3e283f7490ddce5ae ] The selftests added to our CI by Bui Quang Minh recently reveals that there is a mem leak on the error path of virtnet_xsk_pool_enable(): unreferenced object 0xffff88800a68a000 (size 2048): comm "xdp_helper", pid 318, jiffies 4294692778 hex dump (first 32 bytes): 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 ................ 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 ................ backtrace (crc 0): __kvmalloc_node_noprof+0x402/0x570 virtnet_xsk_pool_enable+0x293/0x6a0 (drivers/net/virtio_net.c:5882) xp_assign_dev+0x369/0x670 (net/xdp/xsk_buff_pool.c:226) xsk_bind+0x6a5/0x1ae0 __sys_bind+0x15e/0x230 __x64_sys_bind+0x72/0xb0 do_syscall_64+0xc1/0x1d0 entry_SYSCALL_64_after_hwframe+0x77/0x7f Acked-by: Jason Wang <jasowang@redhat.com> Fixes: e9f3962441c0 ("virtio_net: xsk: rx: support fill with xsk buffer") Link: https://patch.msgid.link/20250430163836.3029761-1-kuba@kernel.org Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
2025-05-18virtio_net: xsk: bind/unbind xsk for txXuan Zhuo
[ Upstream commit 21a4e3ce6dc7b0a3bc882ebe1cb921a40235ddb0 ] This patch implement the logic of bind/unbind xsk pool to sq and rq. Signed-off-by: Xuan Zhuo <xuanzhuo@linux.alibaba.com> Acked-by: Jason Wang <jasowang@redhat.com> Link: https://patch.msgid.link/20241112012928.102478-10-xuanzhuo@linux.alibaba.com Signed-off-by: Jakub Kicinski <kuba@kernel.org> Stable-dep-of: 4397684a292a ("virtio-net: free xsk_buffs on error in virtnet_xsk_pool_enable()") Signed-off-by: Sasha Levin <sashal@kernel.org>
2025-05-18can: rockchip_canfd: rkcanfd_remove(): fix order of unregistration callsMarc Kleine-Budde
commit 037ada7a3181300218e4fd78bef6a741cfa7f808 upstream. If a driver is removed, the driver framework invokes the driver's remove callback. A CAN driver's remove function calls unregister_candev(), which calls net_device_ops::ndo_stop further down in the call stack for interfaces which are in the "up" state. The removal of the module causes a warning, as can_rx_offload_del() deletes the NAPI, while it is still active, because the interface is still up. To fix the warning, first unregister the network interface, which calls net_device_ops::ndo_stop, which disables the NAPI, and then call can_rx_offload_del(). Fixes: ff60bfbaf67f ("can: rockchip_canfd: add driver for Rockchip CAN-FD controller") Cc: stable@vger.kernel.org Link: https://patch.msgid.link/20250502-can-rx-offload-del-v1-2-59a9b131589d@pengutronix.de Reviewed-by: Markus Schneider-Pargmann <msp@baylibre.com> Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2025-05-18can: mcp251xfd: mcp251xfd_remove(): fix order of unregistration callsMarc Kleine-Budde
commit 84f5eb833f53ae192baed4cfb8d9eaab43481fc9 upstream. If a driver is removed, the driver framework invokes the driver's remove callback. A CAN driver's remove function calls unregister_candev(), which calls net_device_ops::ndo_stop further down in the call stack for interfaces which are in the "up" state. With the mcp251xfd driver the removal of the module causes the following warning: | WARNING: CPU: 0 PID: 352 at net/core/dev.c:7342 __netif_napi_del_locked+0xc8/0xd8 as can_rx_offload_del() deletes the NAPI, while it is still active, because the interface is still up. To fix the warning, first unregister the network interface, which calls net_device_ops::ndo_stop, which disables the NAPI, and then call can_rx_offload_del(). Fixes: 55e5b97f003e ("can: mcp25xxfd: add driver for Microchip MCP25xxFD SPI CAN") Cc: stable@vger.kernel.org Link: https://patch.msgid.link/20250502-can-rx-offload-del-v1-1-59a9b131589d@pengutronix.de Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2025-05-18can: mcan: m_can_class_unregister(): fix order of unregistration callsMarc Kleine-Budde
commit 0713a1b3276b98c7dafbeefef00d7bc3a9119a84 upstream. If a driver is removed, the driver framework invokes the driver's remove callback. A CAN driver's remove function calls unregister_candev(), which calls net_device_ops::ndo_stop further down in the call stack for interfaces which are in the "up" state. The removal of the module causes a warning, as can_rx_offload_del() deletes the NAPI, while it is still active, because the interface is still up. To fix the warning, first unregister the network interface, which calls net_device_ops::ndo_stop, which disables the NAPI, and then call can_rx_offload_del(). Fixes: 1be37d3b0414 ("can: m_can: fix periph RX path: use rx-offload to ensure skbs are sent from softirq context") Cc: stable@vger.kernel.org Link: https://patch.msgid.link/20250502-can-rx-offload-del-v1-3-59a9b131589d@pengutronix.de Reviewed-by: Markus Schneider-Pargmann <msp@baylibre.com> Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2025-05-09net: vertexcom: mse102x: Fix RX error handlingStefan Wahren
[ Upstream commit ee512922ddd7d64afe2b28830a88f19063217649 ] In case the CMD_RTS got corrupted by interferences, the MSE102x doesn't allow a retransmission of the command. Instead the Ethernet frame must be shifted out of the SPI FIFO. Since the actual length is unknown, assume the maximum possible value. Fixes: 2f207cbf0dd4 ("net: vertexcom: Add MSE102x SPI support") Signed-off-by: Stefan Wahren <wahrenst@gmx.net> Reviewed-by: Andrew Lunn <andrew@lunn.ch> Link: https://patch.msgid.link/20250430133043.7722-5-wahrenst@gmx.net Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
2025-05-09net: vertexcom: mse102x: Add range check for CMD_RTSStefan Wahren
[ Upstream commit d4dda902dac194e3231a1ed0f76c6c3b6340ba8a ] Since there is no protection in the SPI protocol against electrical interferences, the driver shouldn't blindly trust the length payload of CMD_RTS. So introduce a bounds check for incoming frames. Fixes: 2f207cbf0dd4 ("net: vertexcom: Add MSE102x SPI support") Signed-off-by: Stefan Wahren <wahrenst@gmx.net> Reviewed-by: Andrew Lunn <andrew@lunn.ch> Link: https://patch.msgid.link/20250430133043.7722-4-wahrenst@gmx.net Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
2025-05-09net: vertexcom: mse102x: Fix LEN_MASKStefan Wahren
[ Upstream commit 74987089ec678b4018dba0a609e9f4bf6ef7f4ad ] The LEN_MASK for CMD_RTS doesn't cover the whole parameter mask. The Bit 11 is reserved, so adjust LEN_MASK accordingly. Fixes: 2f207cbf0dd4 ("net: vertexcom: Add MSE102x SPI support") Signed-off-by: Stefan Wahren <wahrenst@gmx.net> Reviewed-by: Andrew Lunn <andrew@lunn.ch> Link: https://patch.msgid.link/20250430133043.7722-3-wahrenst@gmx.net Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
2025-05-09net: vertexcom: mse102x: Fix possible stuck of SPI interruptStefan Wahren
[ Upstream commit 55f362885951b2d00fd7fbb02ef0227deea572c2 ] The MSE102x doesn't provide any SPI commands for interrupt handling. So in case the interrupt fired before the driver requests the IRQ, the interrupt will never fire again. In order to fix this always poll for pending packets after opening the interface. Fixes: 2f207cbf0dd4 ("net: vertexcom: Add MSE102x SPI support") Signed-off-by: Stefan Wahren <wahrenst@gmx.net> Reviewed-by: Andrew Lunn <andrew@lunn.ch> Link: https://patch.msgid.link/20250430133043.7722-2-wahrenst@gmx.net Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
2025-05-09net: hns3: defer calling ptp_clock_register()Jian Shen
[ Upstream commit 4971394d9d624f91689d766f31ce668d169d9959 ] Currently the ptp_clock_register() is called before relative ptp resource ready. It may cause unexpected result when upper layer called the ptp API during the timewindow. Fix it by moving the ptp_clock_register() to the function end. Fixes: 0bf5eb788512 ("net: hns3: add support for PTP") Signed-off-by: Jian Shen <shenjian15@huawei.com> Signed-off-by: Jijie Shao <shaojijie@huawei.com> Reviewed-by: Vadim Fedorenko <vadim.fedorenko@linux.dev> Link: https://patch.msgid.link/20250430093052.2400464-5-shaojijie@huawei.com Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
2025-05-09net: hns3: fixed debugfs tm_qset sizeHao Lan
[ Upstream commit e317aebeefcb3b0c71f2305af3c22871ca6b3833 ] The size of the tm_qset file of debugfs is limited to 64 KB, which is too small in the scenario with 1280 qsets. The size needs to be expanded to 1 MB. Fixes: 5e69ea7ee2a6 ("net: hns3: refactor the debugfs process") Signed-off-by: Hao Lan <lanhao@huawei.com> Signed-off-by: Peiyang Wang <wangpeiyang1@huawei.com> Signed-off-by: Jijie Shao <shaojijie@huawei.com> Link: https://patch.msgid.link/20250430093052.2400464-4-shaojijie@huawei.com Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
2025-05-09net: hns3: fix an interrupt residual problemYonglong Liu
[ Upstream commit 8e6b9c6ea5a55045eed6526d8ee49e93192d1a58 ] When a VF is passthrough to a VM, and the VM is killed, the reported interrupt may not been handled, it will remain, and won't be clear by the nic engine even with a flr or tqp reset. When the VM restart, the interrupt of the first vector may be dropped by the second enable_irq in vfio, see the issue below: https://gitlab.com/qemu-project/qemu/-/issues/2884#note_2423361621 We notice that the vfio has always behaved this way, and the interrupt is a residue of the nic engine, so we fix the problem by moving the vector enable process out of the enable_irq loop. Fixes: 08a100689d4b ("net: hns3: re-organize vector handle") Signed-off-by: Yonglong Liu <liuyonglong@huawei.com> Signed-off-by: Jijie Shao <shaojijie@huawei.com> Link: https://patch.msgid.link/20250430093052.2400464-3-shaojijie@huawei.com Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
2025-05-09net: hns3: store rx VLAN tag offload state for VFJian Shen
[ Upstream commit ef2383d078edcbe3055032436b16cdf206f26de2 ] The VF driver missed to store the rx VLAN tag strip state when user change the rx VLAN tag offload state. And it will default to enable the rx vlan tag strip when re-init VF device after reset. So if user disable rx VLAN tag offload, and trig reset, then the HW will still strip the VLAN tag from packet nad fill into RX BD, but the VF driver will ignore it for rx VLAN tag offload disabled. It may cause the rx VLAN tag dropped. Fixes: b2641e2ad456 ("net: hns3: Add support of hardware rx-vlan-offload to HNS3 VF driver") Signed-off-by: Jian Shen <shenjian15@huawei.com> Signed-off-by: Jijie Shao <shaojijie@huawei.com> Reviewed-by: Simon Horman <horms@kernel.org> Link: https://patch.msgid.link/20250430093052.2400464-2-shaojijie@huawei.com Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
generated by cgit v1.2.3 (git 2.39.1) at 2025-08-01 22:46:58 +0000