| Age | Commit message (Collapse) | Author |
|---|
|
Delay initialization of the service timer and service task until late
probe. If we don't wait, failures in probe do not properly cleanup the
service timer or service task items, which results in the kernel panic
below, potentially freezing the whole system. In addition, ensure that
the SERVICE_DISABLE bit is set before we request the MBX IRQ since the
MBX interrupt attempts to schedule the service task otherwise. This
prevents a similar trace from occurring after this change.
We didn't notice this issue before because probe almost always completes
successfully. I discovered it due to a mis-ordered mailbox handler
array, which resulted in the following failure when requesting mailbox
interrupt.
[ 555.325619] ------------[ cut here ]------------
[ 555.325628] WARNING: CPU: 0 PID: 4941 at lib/list_debug.c:33 __list_add+0xa0/0xd0()
[ 555.325631] list_add corruption. prev->next should be next (ffffffff81f46648), but was (null). (prev=ffff8807fad5d0e8).
<snip>
[ 555.325722] CPU: 0 PID: 4941 Comm: insmod Tainted: G OE 4.0.4-303.fc22.x86_64 #1
[ 555.325725] Hardware name: Intel Corporation S2600CO/S2600CO, BIOS SE5C600.86B.02.03.8x23.060520140825 06/05/2014
[ 555.325727] 0000000000000000 00000000b4f161b3 ffff88081a21f8e8 ffffffff81783124
[ 555.325734] 0000000000000000 ffff88081a21f940 ffff88081a21f928 ffffffff8109c66a
[ 555.325740] 0000000064000000 ffff8807fad5d0e8 ffff8807fad5d0e8 ffffffff81f46648
[ 555.325746] Call Trace:
[ 555.325752] [<ffffffff81783124>] dump_stack+0x45/0x57
[ 555.325757] [<ffffffff8109c66a>] warn_slowpath_common+0x8a/0xc0
[ 555.325759] [<ffffffff8109c6f5>] warn_slowpath_fmt+0x55/0x70
[ 555.325763] [<ffffffff813ba270>] __list_add+0xa0/0xd0
[ 555.325768] [<ffffffff81102d1d>] __internal_add_timer+0x9d/0x110
[ 555.325771] [<ffffffff81102dbf>] internal_add_timer+0x2f/0xc0
[ 555.325774] [<ffffffff81104e5a>] mod_timer+0x12a/0x230
[ 555.325782] [<ffffffffa03d54ca>] fm10k_probe+0x69a/0xc80 [fm10k]
[ 555.325787] [<ffffffff813e8355>] local_pci_probe+0x45/0xa0
[ 555.325791] [<ffffffff8129cf42>] ? sysfs_do_create_link_sd.isra.2+0x72/0xc0
[ 555.325794] [<ffffffff813e96b9>] pci_device_probe+0xf9/0x150
[ 555.325799] [<ffffffff814d7e73>] driver_probe_device+0xa3/0x400
[ 555.325802] [<ffffffff814d82ab>] __driver_attach+0x9b/0xa0
[ 555.325805] [<ffffffff814d8210>] ? __device_attach+0x40/0x40
[ 555.325808] [<ffffffff814d5bd3>] bus_for_each_dev+0x73/0xc0
[ 555.325811] [<ffffffff814d78ce>] driver_attach+0x1e/0x20
[ 555.325815] [<ffffffff814d7480>] bus_add_driver+0x180/0x250
[ 555.325819] [<ffffffffa03b2000>] ? 0xffffffffa03b2000
[ 555.325823] [<ffffffff814d8aa4>] driver_register+0x64/0xf0
[ 555.325826] [<ffffffff813e7bec>] __pci_register_driver+0x4c/0x50
[ 555.325832] [<ffffffffa03d6ca3>] fm10k_register_pci_driver+0x23/0x30 [fm10k]
[ 555.325838] [<ffffffffa03b2080>] fm10k_init_module+0x80/0x1000 [fm10k]
[ 555.325843] [<ffffffff81002128>] do_one_initcall+0xb8/0x200
[ 555.325848] [<ffffffff811e10d2>] ? __vunmap+0xa2/0x100
[ 555.325852] [<ffffffff811fe239>] ? kmem_cache_alloc_trace+0x1b9/0x240
[ 555.325855] [<ffffffff8178230e>] ? do_init_module+0x28/0x1cb
[ 555.325858] [<ffffffff81782346>] do_init_module+0x60/0x1cb
[ 555.325862] [<ffffffff8112168e>] load_module+0x205e/0x26b0
[ 555.325866] [<ffffffff8111d110>] ? store_uevent+0x70/0x70
[ 555.325870] [<ffffffff812234b0>] ? kernel_read+0x50/0x80
[ 555.325873] [<ffffffff81121f3e>] SyS_finit_module+0xbe/0xf0
[ 555.325878] [<ffffffff81789749>] system_call_fastpath+0x12/0x17
[ 555.325880] ---[ end trace 9e0f58d071eafd2a ]---
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Krishneil Singh <Krishneil.k.singh@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
According to the C standard dereferencing a variable before it is
checked invokes undefined behavior, and thus compilers are free to
assume the check for NULL isn't necessary. Prevent this by re-ordering
the NULL check of msix_entries in fm10k_free_mbx_irq.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Krishneil Singh <Krishneil.k.singh@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
Cleanup the remaining instances of using memcpy() instead of the preferred
ether_addr_copy().
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Krishneil Singh <Krishneil.k.singh@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Krishneil Singh <Krishneil.k.singh@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
We don't need to crash the kernel in this instance so just warn about the
condition and play on.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Krishneil Singh <Krishneil.k.singh@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
Use BIT() macro instead.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Krishneil Singh <Krishneil.k.singh@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
The semantic patch that makes this change is available
in scripts/coccinelle/misc/compare_const_fl.cocci.
More information about semantic patching is available at
http://coccinelle.lip6.fr/
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Krishneil Singh <Krishneil.k.singh@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
Signed-off-by: Catherine Sullivan <catherine.sullivan@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
Minor correction in the comment to reflect the correct function name
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
If the driver happens to read a register during the time in which the
device is undergoing reset, it will receive a value of 0xdeadbeef
instead of a valid value. Unfortunately, the driver may misinterpret
this as a valid value, especially if it's just looking for individual
bits.
Add an explicit check for this value when we are looking for admin queue
errors, and trigger reset recovery if we find it.
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
There's no real error in an unknown event from the Firmware, we're just
posting a useful FYI notice, so this patch simply removes the "Error" word.
Signed-off-by: Shannon Nelson <shannon.nelson@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
Clear the VFLR bit after reset processing, instead of before. This
prevents double resets on VF init.
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
Notify VFs in the reset interrupt handler, instead of the actual
reset initiation code. This allows the VFs to get properly notified for
all resets, including resets initiated by different PFs on the same
physical device.
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
In some error scenarios, we may find ourselves trying to remove a
non-existent timer or worktask. This causes the kernel some bit
of consternation, so don't do it.
Signed-off-by: Shannon Nelson <shannon.nelson@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
Export to userspace the front panel name of the port, so that udev can
rename the ports accordingly. The convention suggested by switchdev
documentation is used:
1) Non-split: pX
2) Split: pXsY
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Resources allocated for these bridges at init time cannot be later used
for other purposes. While current number is supported by the device,
it's mostly theoretical with regards to any real use case, which leads
to poor utilization of device's resources. Solve that by reducing the
number.
The long term plan is to make this value (along with others) user
configurable via devlink and write it to NVRAM, so that it can be used
during the next init. Until then we must hardcode such values.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When dropping into debug mode in a failed probe, make sure that
the AdminQ is left alive for possible hand debug of driver and
firmware states.
Move the mutex_init calls earlier in probe so that if init fails,
the admin queue interface is still available for debugging purposes.
Signed-off-by: Shannon Nelson <shannon.nelson@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
When cleaning up the interrupt handling, clean up the IRQs only if
we actually got them set up. There are a couple of error recovery
paths that were violating this and causing the kernel a bit of
indigestion.
Signed-off-by: Shannon Nelson <shannon.nelson@intel.com>
Reviewed-by: Williams, Mitch A <mitch.a.williams@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
The i40e_common.c typically uses i40e_status as a return code,
but got missed this one case.
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
When updating a VSI, save off the number of allocated and unallocated
VSIs as we do when adding a VSI.
Signed-off-by: Kevin Scott <kevin.c.scott@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
This patch removes the duplicate definition of I40E_MAX_USER_PRIORITY
in i40e.h that is not needed.
Signed-off-by: Catherine Sullivan <catherine.sullivan@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
Simple cast to fix a sparse warning.
Fixes: commit 5453205cd097 ("i40e/i40evf: Enable support for
SKB_GSO_UDP_TUNNEL_CSUM")
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
This patch enables bulk Tx clean for skbs. In order to enable it we need
to pass the napi_budget value as that is used to determine if we are truly
running in NAPI mode or if we are simply calling the routine from netpoll
with a budget of 0. In order to avoid adding too many more variables I
thought it best to pass the VSI directly in a fashion similar to what we do
on igb and ixgbe with the q_vector.
Signed-off-by: Alexander Duyck <aduyck@mirantis.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
If the hw scan request specifies a single BSSID, use that value instead
of the wildcard BSSID in the Probe Request frames.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
In the polling routines for i40e and i40evf we were using bitwise operators
to avoid the side effects of the logical operators, specifically the fact
that if the first case is true with "||" we skip the second case, or if it
is false with "&&" we skip the second case. This fixes an earlier patch
that converted the bitwise operators over to the logical operators and
instead replaces the entire thing with just an if statement since it should
be more readable what we are trying to do this way.
Fixes: 1a36d7fadd14 ("i40e/i40evf: use logical operators, not bitwise")
Signed-off-by: Alexander Duyck <aduyck@mirantis.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
When HW crypto is used, there's no need for the CCMP/GCMP MIC to
be available to mac80211, and the hardware might have removed it
already after checking. The MIC is also useless to have when the
frame is already decrypted, so allow indicating that it's not
present.
Since we are running out of bits in mac80211_rx_flags, make
the flags field a u64.
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
The only error case is when the malloc fails, in which case the clean up
loop does nothing at all, so remove it
Signed-off-by: Alan Cox <alan@linux.intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
From what I can tell the practical limitation on the size of the Tx data
buffer is the fact that the Tx descriptor is limited to 14 bits. As such
we cannot use 16K as is typically used on the other Intel drivers. However
artificially limiting ourselves to 8K can be expensive as this means that
we will consume up to 10 descriptors (1 context, 1 for header, and 9 for
payload, non-8K aligned) in a single send.
I propose that we can reduce this by increasing the maximum data for a 4K
aligned block to 12K. We can reduce the descriptors used for a 32K aligned
block by 1 by increasing the size like this. In addition we still have the
4K - 1 of space that is still unused. We can use this as a bit of extra
padding when dealing with data that is not aligned to 4K.
By aligning the descriptors after the first to 4K we can improve the
efficiency of PCIe accesses as we can avoid using byte enables and can fetch
full TLP transactions after the first fetch of the buffer. This helps to
improve PCIe efficiency. Below is the results of testing before and after
with this patch:
Recv Send Send Utilization Service Demand
Socket Socket Message Elapsed Send Recv Send Recv
Size Size Size Time Throughput local remote local remote
bytes bytes bytes secs. 10^6bits/s % S % U us/KB us/KB
Before:
87380 16384 16384 10.00 33682.24 20.27 -1.00 0.592 -1.00
After:
87380 16384 16384 10.00 34204.08 20.54 -1.00 0.590 -1.00
So the net result of this patch is that we have a small gain in throughput
due to a reduction in overhead for putting together the frame.
Signed-off-by: Alexander Duyck <aduyck@mirantis.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
Calling dev_close() causes IFF_UP to be cleared which will remove the
interfaces routes and some addresses. That's probably not what the user
intended when running the offline selftest. Besides this does not happen
if the interface is brought down before the test, so the current
behaviour is inconsistent.
Instead call the net_device_ops ndo_stop function directly and avoid
touching IFF_UP at all.
Signed-off-by: Stefan Assmann <sassmann@kpanic.de>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/jkirsher/next-queue
Jeff Kirsher says:
====================
10GbE Intel Wired LAN Driver Updates 2016-04-04
This series contains updates to ixgbe and ixgbevf.
Pavel Tikhomirov fixes a typo where we were incrementing transmit stats
instead of receive stats on the receive side.
Emil updates the ixgbevf driver to use bit operations for setting and
checking the adapter state.
Chas Williams adds the new NDO trust feature check so that the VF guest
has the ability to set the unicast address of the interface, if it is a
trusted VF.
Alex cleans up the driver to that the only time we add a PF entry to the
VLVF is either for VLAN 0 or if the PF has requested a VLAN that a VF
is already using. Also adds support for generic transmit checksums,
giving the added advantage is that we can support inner checksum offloads
for tunnels and MPLS while still being able to transparently insert
VLAN tags. Lastly, changed ixgbe so that we can use the ethtool
rx-vlan-filter flag to toggle receive VLAN filtering on and off.
Mark cleans up the ixgbe driver by making all op structures that do not
change constants. Also fixed flow control for Xeon D KR backplanes, since
we cannot use auto-negotiation to determine the mode, we have to use
whatever the user configured.
Sowmini Varadhan updates ixgbe to use eth_platform_get_mac_address()
instead of the arch specific solution that was added by a previous
commit.
Don fixed an issue where it was possible that a system reset could occur
when we were holding the SWFW semaphore lock, which the next time the
driver loaded would see it incorrectly as locked.
v2: updated patch 8 of the series to include a minor flags issue where
we had lost NETIF_F_HW_TC and we were setting NETIF_F_SCTP_CRC in
two different areas, when we only needed/wanted it in one spot.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
By adding support for bridge operations, FDB operations, and optionally
VLAN operations (for 802.1Q and VLAN filtering aware systems), the
switch bridges ports correctly, the CPU is able to populate the hardware
address databases, and thus hardware bridging becomes functional within
the 88E6185 family of switches.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The 88E6185 switch also has a MapDA bit in its Port Control 2 register.
When this bit is cleared, all frames are sent out to the CPU port.
Set this bit to rely on address databases (ATU) hits and direct frames
out of the correct ports, and thus allow hardware bridging.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The 6185 family of devices has only 256 address databases. Their 8-bit
FID for ATU and VTU operations are split into ATU Control and ATU/VTU
Operation registers.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Marvell switch chips have different number of address databases.
The code currently only supports models with 4096 databases. Such switch
has dedicated FID registers for ATU and VTU operations. Models with
fewer databases have their FID split in several registers.
List them all but only support models with 4096 databases at the moment.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Only switch families with 4096 address databases have dedicated FID
registers for ATU and VTU operations.
Factorize the access to the GLOBAL_ATU_FID register and introduce a
mv88e6xxx_has_fid_reg() helper function to protect the access to
GLOBAL_ATU_FID and GLOBAL_VTU_FID.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Introduce a mv88e6xxx_has_stu() helper to protect the access to the
GLOBAL_VTU_SID register, instead of checking switch families.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This change makes it so that we can use the ethtool rx-vlan-filter flag to
toggle Rx VLAN filtering on and off. This is basically just an extension
of the existing VLAN promisc work in that it just adds support for the
additional ethtool flag.
Signed-off-by: Alexander Duyck <aduyck@mirantis.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
Added support to match on UDP fields in the transport layer.
Extended core logic to support multiple headers.
Verified with the following filters :
handle 1: u32 divisor 1
u32 ht 800: order 1 link 1: \
offset at 0 mask 0f00 shift 6 plus 0 eat match ip protocol 6 ff
u32 ht 1: order 2 \
match tcp src 1024 ffff match tcp dst 23 ffff action drop
handle 2: u32 divisor 1
u32 ht 800: order 3 link 2: \
offset at 0 mask 0f00 shift 6 plus 0 eat match ip protocol 17 ff
u32 ht 2: order 4 \
match udp src 1025 ffff match udp dst 24 ffff action drop
Signed-off-by: Amritha Nambiar <amritha.nambiar@intel.com>
Acked-by: John Fastabend <john.r.fastabend@intel.com>
Acked-by: Sridhar Samudrala <sridhar.samudrala@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
It is possible on some HW that a system reset could occur when we are
holding the SWFW semaphore lock. So next time the driver was loaded we
would see it incorrectly as locked. This patch will recover from that state
by: Attempting to acquire the semaphore and then regardless of whether or
not it was acquire we immediately release it. This will force us into
a known good state.
Signed-off-by: Don Skidmore <donald.c.skidmore@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
This commit adds a callback which allows to adjust the maximum transmit
bitrate the card can output. This makes it possible to get a smooth
traffic instead of the default burst-y behaviour when trying to output
e.g. a video stream.
Much of the logic needed to get a correct bcnrc_val was taken from the
ixgbe_set_vf_rate_limit() function.
Signed-off-by: Rostislav Pehlivanov <atomnuker@gmail.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
Xeon D KR backplane is different from other backplanes,
in that we can't use auto-negotiation to determine the
mode. Instead, use whatever the user configured.
Signed-off-by: Mark Rustad <mark.d.rustad@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
This patch adds support for generic Tx checksums to the ixgbevf driver. It
turns out this is actually pretty easy after going over the datasheet as we
were doing a number of steps we didn't need to.
In order to perform a Tx checksum for an L4 header we need to fill in the
following fields in the Tx descriptor:
MACLEN (maximum of 127), retrieved from:
skb_network_offset()
IPLEN (maximum of 511), retrieved from:
skb_checksum_start_offset() - skb_network_offset()
TUCMD.L4T indicates offset and if checksum or crc32c, based on:
skb->csum_offset
The added advantage to doing this is that we can support inner checksum
offloads for tunnels and MPLS while still being able to transparently
insert VLAN tags.
I also took the opportunity to clean-up many of the feature flag
configuration bits to make them a bit more consistent between drivers. In
the case of the VF drivers this meant adding support for SCTP CRCs, and
inner checksum offloads for MPLS and various tunnel types.
Signed-off-by: Alexander Duyck <aduyck@mirantis.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
This patch adds support for generic Tx checksums to the ixgbe driver. It
turns out this is actually pretty easy after going over the datasheet as we
were doing a number of steps we didn't need to.
In order to perform a Tx checksum for an L4 header we need to fill in the
following fields in the Tx descriptor:
MACLEN (maximum of 127), retrieved from:
skb_network_offset()
IPLEN (maximum of 511), retrieved from:
skb_checksum_start_offset() - skb_network_offset()
TUCMD.L4T indicates offset and if checksum or crc32c, based on:
skb->csum_offset
The added advantage to doing this is that we can support inner checksum
offloads for tunnels and MPLS while still being able to transparently
insert VLAN tags.
I also took the opportunity to clean-up many of the feature flag
configuration bits to make them a bit more consistent between drivers.
Signed-off-by: Alexander Duyck <aduyck@mirantis.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
This commit converts commit c762dff24c06 ("ixgbe: Look up MAC address in
Open Firmware or IDPROM") to use eth_platform_get_mac_address()
added by commit c7f5d105495a ("net: Add eth_platform_get_mac_address()
helper.")
Signed-off-by: Sowmini Varadhan <sowmini.varadhan@oracle.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
The source for the ops structure contents are const, so make them
so. Copy them in place with structure assignments instead of memcpys.
Make the mbx_ops accessed by reference instead of making a copy of
the source structure. Update copyright date on the touched files.
Reported-by: Julia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: Mark Rustad <mark.d.rustad@intel.com>
Acked-by: Julia Lawall <julia.lawall@lip6.fr>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
We were adding VLAN 0 twice each time we restored the VLAN configuration.
Instead of doing it twice we can just start working through the active
VLANs from ID 1 on and skip the double write.
Signed-off-by: Alexander Duyck <aduyck@mirantis.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
Remove the sh-irda driver as it appears to be unused since
c0bb9b302769 ("ARCH: ARM: shmobile: Remove ag5evm board support").
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Acked-by: Michal Simek <michal.simek@xilinx.com>
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: Moritz Fischer <moritz.fischer@ettus.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Checkpatch suggests using ether_addr_copy over memcpy
to copy the mac address.
Acked-by: Michal Simek <michal.simek@xilinx.com>
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: Moritz Fischer <moritz.fischer@ettus.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This commit deals with a bunch of checkpatch suggestions
that without changing behavior make checkpatch happier.
Acked-by: Michal Simek <michal.simek@xilinx.com>
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: Moritz Fischer <moritz.fischer@ettus.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
