| Age | Commit message (Collapse) | Author |
|---|
|
Since device MAC types are constantly being added, the judgments of
wx->mac.type are complex. Try to convert the types to flags depending
on functions.
Signed-off-by: Jiawen Wu <jiawenwu@trustnetic.com>
Link: https://patch.msgid.link/20250221065718.197544-2-jiawenwu@trustnetic.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
There is a new 40/25/10 Gigabit Ethernet device.
To support basic functions, PHYLINK is temporarily skipped as it is
intended to implement these configurations in the firmware. And the
associated link IRQ is also skipped.
And Implement the new SW-FW interaction interface, which use 64 Byte
message buffer.
Signed-off-by: Jiawen Wu <jiawenwu@trustnetic.com>
Link: https://patch.msgid.link/20250221065718.197544-1-jiawenwu@trustnetic.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Remove the unnecessary bool conversion and simplify the code.
Signed-off-by: Thorsten Blum <thorsten.blum@linux.dev>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Link: https://patch.msgid.link/20250223233613.100518-2-thorsten.blum@linux.dev
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
thead was checking that the stmmac_clk rate was a multiple of the
RGMII rates for 1G and 100M, but didn't check for 10M. Rather than
use this with hard-coded speeds, check that the calculated divisor
gives the required rate by multplying the transmit clock rate back
up to the stmmac clock rate and checking that it agrees.
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Tested-by: Drew Fustini <drew@pdp7.com>
Link: https://patch.msgid.link/E1tlToD-004W3g-HB@rmk-PC.armlinux.org.uk
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Switch to using rgmii_clock() to get the RGMII TXC rate, and calculate
the divisor from the parent clock rate and the rate indicated by
rgmii_clock().
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Tested-by: Drew Fustini <drew@pdp7.com>
Link: https://patch.msgid.link/E1tlTo8-004W3a-CO@rmk-PC.armlinux.org.uk
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Only one version of skb_flow_get_ports() exists after the previous commit,
so let's remove the useless '__'.
Suggested-by: Simon Horman <horms@kernel.org>
Signed-off-by: Nicolas Dichtel <nicolas.dichtel@6wind.com>
Link: https://patch.msgid.link/20250221110941.2041629-3-nicolas.dichtel@6wind.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
The maximum numbers of each Rx and Tx queues are defined by
MTL_MAX_RX_QUEUES and MTL_MAX_TX_QUEUES respectively.
There are some places where Rx and Tx are used in reverse. There is no
issue when the Tx and Rx macros have the same value, but should correct
usage of macros for maximum queue number to keep consistency and prevent
unexpected mistakes.
Reviewed-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Reviewed-by: Huacai Chen <chenhuacai@kernel.org>
Signed-off-by: Kunihiko Hayashi <hayashi.kunihiko@socionext.com>
Link: https://patch.msgid.link/20250221051818.4163678-1-hayashi.kunihiko@socionext.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Test XDP and HDS interaction. While at it add a test for using the IOCTL,
as that turned out to be the real culprit.
Testing bnxt:
# NETIF=eth0 ./ksft-net-drv/drivers/net/hds.py
KTAP version 1
1..12
ok 1 hds.get_hds
ok 2 hds.get_hds_thresh
ok 3 hds.set_hds_disable # SKIP disabling of HDS not supported by the device
ok 4 hds.set_hds_enable
ok 5 hds.set_hds_thresh_zero
ok 6 hds.set_hds_thresh_max
ok 7 hds.set_hds_thresh_gt
ok 8 hds.set_xdp
ok 9 hds.enabled_set_xdp
ok 10 hds.ioctl
ok 11 hds.ioctl_set_xdp
ok 12 hds.ioctl_enabled_set_xdp
# Totals: pass:11 fail:0 xfail:0 xpass:0 skip:1 error:0
and netdevsim:
# ./ksft-net-drv/drivers/net/hds.py
KTAP version 1
1..12
ok 1 hds.get_hds
ok 2 hds.get_hds_thresh
ok 3 hds.set_hds_disable
ok 4 hds.set_hds_enable
ok 5 hds.set_hds_thresh_zero
ok 6 hds.set_hds_thresh_max
ok 7 hds.set_hds_thresh_gt
ok 8 hds.set_xdp
ok 9 hds.enabled_set_xdp
ok 10 hds.ioctl
ok 11 hds.ioctl_set_xdp
ok 12 hds.ioctl_enabled_set_xdp
# Totals: pass:12 fail:0 xfail:0 xpass:0 skip:0 error:0
Netdevsim needs a sane default for tx/rx ring size.
ethtool 6.11 is needed for the --disable-netlink option.
Acked-by: Stanislav Fomichev <sdf@fomichev.me>
Tested-by: Taehee Yoo <ap420073@gmail.com>
Link: https://patch.msgid.link/20250221025141.1132944-2-kuba@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
The link clock operates at twice the RGMII clock rate. Therefore, we
can use the rgmii_clock() helper to set this clock rate.
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Reviewed-by: Vinod Koul <vkoul@kernel.org>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://patch.msgid.link/E1tlRMK-004Vsx-Ss@rmk-PC.armlinux.org.uk
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
When the kernel is compiled without LED framework support the
rtl8366rb fails to build like this:
rtl8366rb.o: in function `rtl8366rb_setup_led':
rtl8366rb.c:953:(.text.unlikely.rtl8366rb_setup_led+0xe8):
undefined reference to `led_init_default_state_get'
rtl8366rb.c:980:(.text.unlikely.rtl8366rb_setup_led+0x240):
undefined reference to `devm_led_classdev_register_ext'
As this is constantly coming up in different randconfig builds,
bite the bullet and create a separate file for the offending
code, split out a header with all stuff needed both in the
core driver and the leds code.
Add a new bool Kconfig option for the LED compile target, such
that it depends on LEDS_CLASS=y || LEDS_CLASS=RTL8366RB
which make LED support always available when LEDS_CLASS is
compiled into the kernel and enforce that if the LEDS_CLASS
is a module, then the RTL8366RB driver needs to be a module
as well so that modprobe can resolve the dependencies.
Fixes: 32d617005475 ("net: dsa: realtek: add LED drivers for rtl8366rb")
Reported-by: kernel test robot <lkp@intel.com>
Closes: https://lore.kernel.org/oe-kbuild-all/202502070525.xMUImayb-lkp@intel.com/
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
There are several issues existed in start_xmit():
- Transmitted packets need to be freed before sending a packet, this
introduces delay and increases the average packets transmit
time. This also increase the time that spent in holding the TX lock.
- Notification is enabled after free_old_xmit_skbs() which will
introduce unnecessary interrupts if TX notification happens on the
same CPU that is doing the transmission now (actually, virtio-net
driver are optimized for this case).
So this patch tries to avoid those issues by not cleaning transmitted
packets in start_xmit() when TX NAPI is enabled and disable
notifications even more aggressively. Notification will be since the
beginning of the start_xmit(). But we can't enable delayed
notification after TX is stopped as we will lose the
notifications. Instead, the delayed notification needs is enabled
after the virtqueue is kicked for best performance.
Performance numbers:
1) single queue 2 vcpus guest with pktgen_sample03_burst_single_flow.sh
(burst 256) + testpmd (rxonly) on the host:
- When pinning TX IRQ to pktgen VCPU: split virtqueue PPS were
increased 55% from 6.89 Mpps to 10.7 Mpps and 32% TX interrupts were
eliminated. Packed virtqueue PPS were increased 50% from 7.09 Mpps to
10.7 Mpps, 99% TX interrupts were eliminated.
- When pinning TX IRQ to VCPU other than pktgen: split virtqueue PPS
were increased 96% from 5.29 Mpps to 10.4 Mpps and 45% TX interrupts
were eliminated; Packed virtqueue PPS were increased 78% from 6.12
Mpps to 10.9 Mpps and 99% TX interrupts were eliminated.
2) single queue 1 vcpu guest + vhost-net/TAP on the host: single
session netperf from guest to host shows 82% improvement from
31Gb/s to 58Gb/s, %stddev were reduced from 34.5% to 1.9% and 88%
of TX interrupts were eliminated.
Signed-off-by: Jason Wang <jasowang@redhat.com>
Acked-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Change POOL_NEXT_SIZE define value from 0 to BIT(30), since this define
is used to request the available maximum sized flow table, and zero doesn't
make sense for it, whereas some places in the driver use zero explicitly
expecting the smallest table size possible but instead due to this
define they end up allocating the biggest table size unawarely.
In addition move the definition to "include/linux/mlx5/fs.h" to expose the
define to IB driver as well, while appropriately renaming it.
Signed-off-by: Patrisious Haddad <phaddad@nvidia.com>
Reviewed-by: Maor Gottlieb <maorg@nvidia.com>
Reviewed-by: Mark Bloch <mbloch@nvidia.com>
Signed-off-by: Tariq Toukan <tariqt@nvidia.com>
Link: https://patch.msgid.link/20250219085808.349923-3-tariqt@nvidia.com
Signed-off-by: Leon Romanovsky <leon@kernel.org>
|
|
Add an implementation for DMTF DSP0283, which defines a MCTP-over-USB
transport. As per that spec, we're restricted to full speed mode,
requiring 512-byte transfers.
Each MCTP-over-USB interface is a peer-to-peer link to a single MCTP
endpoint, so no physical addressing is required (of course, that MCTP
endpoint may then bridge to further MCTP endpoints). Consequently,
interfaces will report with no lladdr data:
# mctp link
dev lo index 1 address 00:00:00:00:00:00 net 1 mtu 65536 up
dev mctpusb0 index 6 address none net 1 mtu 68 up
This is a simple initial implementation, with single rx & tx urbs, and
no multi-packet tx transfers - although we do accept multi-packet rx
from the device.
Includes suggested fixes from Santosh Puranik <spuranik@nvidia.com>.
Signed-off-by: Jeremy Kerr <jk@codeconstruct.com.au>
Cc: Santosh Puranik <spuranik@nvidia.com>
Link: https://patch.msgid.link/20250221-dev-mctp-usb-v3-2-3353030fe9cc@codeconstruct.com.au
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Implement byte queue limits to allow queuing disciplines to account for
packets enqueued in the ring buffer but not yet transmitted. There are a
separate set of transmit functions for AT91 that I haven't touched since
I don't have hardware to test on.
Signed-off-by: Sean Anderson <sean.anderson@linux.dev>
Link: https://patch.msgid.link/20250220164257.96859-1-sean.anderson@linux.dev
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Stats calculations involve a RMW to add the stat update to the existing
value. This is currently not protected by any synchronization mechanism,
so data races are possible. Add a spinlock to protect the update. The
reader side could be protected using u64_stats, but we would still need
a spinlock for the update side anyway. And we always do an update
immediately before reading the stats anyway.
Fixes: 89e5785fc8a6 ("[PATCH] Atmel MACB ethernet driver")
Signed-off-by: Sean Anderson <sean.anderson@linux.dev>
Link: https://patch.msgid.link/20250220162950.95941-1-sean.anderson@linux.dev
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
syzbot found that ipvlan_process_v6_outbound() was assuming
the IPv6 network header isis present in skb->head [1]
Add the needed pskb_network_may_pull() calls for both
IPv4 and IPv6 handlers.
[1]
BUG: KMSAN: uninit-value in __ipv6_addr_type+0xa2/0x490 net/ipv6/addrconf_core.c:47
__ipv6_addr_type+0xa2/0x490 net/ipv6/addrconf_core.c:47
ipv6_addr_type include/net/ipv6.h:555 [inline]
ip6_route_output_flags_noref net/ipv6/route.c:2616 [inline]
ip6_route_output_flags+0x51/0x720 net/ipv6/route.c:2651
ip6_route_output include/net/ip6_route.h:93 [inline]
ipvlan_route_v6_outbound+0x24e/0x520 drivers/net/ipvlan/ipvlan_core.c:476
ipvlan_process_v6_outbound drivers/net/ipvlan/ipvlan_core.c:491 [inline]
ipvlan_process_outbound drivers/net/ipvlan/ipvlan_core.c:541 [inline]
ipvlan_xmit_mode_l3 drivers/net/ipvlan/ipvlan_core.c:605 [inline]
ipvlan_queue_xmit+0xd72/0x1780 drivers/net/ipvlan/ipvlan_core.c:671
ipvlan_start_xmit+0x5b/0x210 drivers/net/ipvlan/ipvlan_main.c:223
__netdev_start_xmit include/linux/netdevice.h:5150 [inline]
netdev_start_xmit include/linux/netdevice.h:5159 [inline]
xmit_one net/core/dev.c:3735 [inline]
dev_hard_start_xmit+0x247/0xa20 net/core/dev.c:3751
sch_direct_xmit+0x399/0xd40 net/sched/sch_generic.c:343
qdisc_restart net/sched/sch_generic.c:408 [inline]
__qdisc_run+0x14da/0x35d0 net/sched/sch_generic.c:416
qdisc_run+0x141/0x4d0 include/net/pkt_sched.h:127
net_tx_action+0x78b/0x940 net/core/dev.c:5484
handle_softirqs+0x1a0/0x7c0 kernel/softirq.c:561
__do_softirq+0x14/0x1a kernel/softirq.c:595
do_softirq+0x9a/0x100 kernel/softirq.c:462
__local_bh_enable_ip+0x9f/0xb0 kernel/softirq.c:389
local_bh_enable include/linux/bottom_half.h:33 [inline]
rcu_read_unlock_bh include/linux/rcupdate.h:919 [inline]
__dev_queue_xmit+0x2758/0x57d0 net/core/dev.c:4611
dev_queue_xmit include/linux/netdevice.h:3311 [inline]
packet_xmit+0x9c/0x6c0 net/packet/af_packet.c:276
packet_snd net/packet/af_packet.c:3132 [inline]
packet_sendmsg+0x93e0/0xa7e0 net/packet/af_packet.c:3164
sock_sendmsg_nosec net/socket.c:718 [inline]
Fixes: 2ad7bf363841 ("ipvlan: Initial check-in of the IPVLAN driver.")
Reported-by: syzbot+93ab4a777bafb9d9f960@syzkaller.appspotmail.com
Closes: https://lore.kernel.org/netdev/67b74f01.050a0220.14d86d.02d8.GAE@google.com/T/#u
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Mahesh Bandewar <maheshb@google.com>
Link: https://patch.msgid.link/20250220155336.61884-1-edumazet@google.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
stmmac_init_dma_engine() uses dev_err() which leads to errors being
reported as e.g:
dwc-eth-dwmac 2490000.ethernet: Failed to reset the dma
dwc-eth-dwmac 2490000.ethernet eth0: stmmac_hw_setup: DMA engine initialization failed
stmmac_init_dma_engine() is only called from stmmac_hw_setup() which
itself uses netdev_err(), and we will have a net_device setup. So,
change the dev_err() to netdev_err() to give consistent error
messages.
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Link: https://patch.msgid.link/E1tl5y1-004UgG-8X@rmk-PC.armlinux.org.uk
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
After commit 22600596b675 ("ipv4: give an IPv4 dev to blackhole_netdev")
IPv4 neighbors can be constructed on the blackhole net device, but they
are constructed with an output function (neigh_direct_output()) that
simply calls dev_queue_xmit(). The latter will transmit packets via
'skb->dev' which might not be the blackhole net device if dst_dev_put()
switched 'dst->dev' to the blackhole net device while another CPU was
using the dst entry in ip_output(), but after it already initialized
'skb->dev' from 'dst->dev'.
Specifically, the following can happen:
CPU1 CPU2
udp_sendmsg(sk1) udp_sendmsg(sk2)
udp_send_skb() [...]
ip_output()
skb->dev = skb_dst(skb)->dev
dst_dev_put()
dst->dev = blackhole_netdev
ip_finish_output2()
resolves neigh on dst->dev
neigh_output()
neigh_direct_output()
dev_queue_xmit()
This will result in IPv4 packets being sent without an Ethernet header
via a valid net device:
tcpdump: verbose output suppressed, use -v[v]... for full protocol decode
listening on enp9s0, link-type EN10MB (Ethernet), snapshot length 262144 bytes
22:07:02.329668 20:00:40:11:18:fb > 45:00:00:44:f4:94, ethertype Unknown
(0x58c6), length 68:
0x0000: 8dda 74ca f1ae ca6c ca6c 0098 969c 0400 ..t....l.l......
0x0010: 0000 4730 3f18 6800 0000 0000 0000 9971 ..G0?.h........q
0x0020: c4c9 9055 a157 0a70 9ead bf83 38ca ab38 ...U.W.p....8..8
0x0030: 8add ab96 e052 .....R
Fix by making sure that neighbors are constructed on top of the
blackhole net device with an output function that simply consumes the
packets, in a similar fashion to dst_discard_out() and
blackhole_netdev_xmit().
Fixes: 8d7017fd621d ("blackhole_netdev: use blackhole_netdev to invalidate dst entries")
Fixes: 22600596b675 ("ipv4: give an IPv4 dev to blackhole_netdev")
Reported-by: Florian Meister <fmei@sfs.com>
Closes: https://lore.kernel.org/netdev/20250210084931.23a5c2e4@hermes.local/
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Reviewed-by: Eric Dumazet <edumazet@google.com>
Link: https://patch.msgid.link/20250220072559.782296-1-idosch@nvidia.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
https://git.kernel.org/pub/scm/linux/kernel/git/bpf/bpf-next
Martin KaFai Lau says:
====================
pull-request: bpf-next 2025-02-20
We've added 19 non-merge commits during the last 8 day(s) which contain
a total of 35 files changed, 1126 insertions(+), 53 deletions(-).
The main changes are:
1) Add TCP_RTO_MAX_MS support to bpf_set/getsockopt, from Jason Xing
2) Add network TX timestamping support to BPF sock_ops, from Jason Xing
3) Add TX metadata Launch Time support, from Song Yoong Siang
* tag 'for-netdev' of https://git.kernel.org/pub/scm/linux/kernel/git/bpf/bpf-next:
igc: Add launch time support to XDP ZC
igc: Refactor empty frame insertion for launch time support
net: stmmac: Add launch time support to XDP ZC
selftests/bpf: Add launch time request to xdp_hw_metadata
xsk: Add launch time hardware offload support to XDP Tx metadata
selftests/bpf: Add simple bpf tests in the tx path for timestamping feature
bpf: Support selective sampling for bpf timestamping
bpf: Add BPF_SOCK_OPS_TSTAMP_SENDMSG_CB callback
bpf: Add BPF_SOCK_OPS_TSTAMP_ACK_CB callback
bpf: Add BPF_SOCK_OPS_TSTAMP_SND_HW_CB callback
bpf: Add BPF_SOCK_OPS_TSTAMP_SND_SW_CB callback
bpf: Add BPF_SOCK_OPS_TSTAMP_SCHED_CB callback
net-timestamp: Prepare for isolating two modes of SO_TIMESTAMPING
bpf: Disable unsafe helpers in TX timestamping callbacks
bpf: Prevent unsafe access to the sock fields in the BPF timestamping callback
bpf: Prepare the sock_ops ctx and call bpf prog for TX timestamping
bpf: Add networking timestamping support to bpf_get/setsockopt()
selftests/bpf: Add rto max for bpf_setsockopt test
bpf: Support TCP_RTO_MAX_MS for bpf_setsockopt
====================
Link: https://patch.msgid.link/20250221022104.386462-1-martin.lau@linux.dev
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Not all the devices have the capability for the driver to query for the
registered RSS configuration. The driver can discover this by checking
the relevant device option during setup. If it cannot, the driver needs
to store the RSS config cache and directly return such cache when
queried by the ethtool. RSS config is inited when driver probes. Also the
default RSS config will be adjusted when there is RX queue count change.
At this point, only keys of GVE_RSS_KEY_SIZE and indirection tables of
GVE_RSS_INDIR_SIZE are supported.
Signed-off-by: Ziwei Xiao <ziweixiao@google.com>
Reviewed-by: Harshitha Ramamurthy <hramamurthy@google.com>
Reviewed-by: Willem de Bruijn <willemb@google.com>
Signed-off-by: Praveen Kaligineedi <pkaligineedi@google.com>
Signed-off-by: Jeroen de Borst <jeroendb@google.com>
Link: https://patch.msgid.link/20250219200451.3348166-1-jeroendb@google.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Add two helper functions - rtnl_newlink_link_net() and
rtnl_newlink_peer_net() for netns fallback logic. Peer netns falls back
to link netns, and link netns falls back to source netns.
Convert the use of params->net in netdevice drivers to one of the helper
functions for clarity.
Signed-off-by: Xiao Liang <shaw.leon@gmail.com>
Reviewed-by: Kuniyuki Iwashima <kuniyu@amazon.com>
Link: https://patch.msgid.link/20250219125039.18024-4-shaw.leon@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
There are 4 net namespaces involved when creating links:
- source netns - where the netlink socket resides,
- target netns - where to put the device being created,
- link netns - netns associated with the device (backend),
- peer netns - netns of peer device.
Currently, two nets are passed to newlink() callback - "src_net"
parameter and "dev_net" (implicitly in net_device). They are set as
follows, depending on netlink attributes in the request.
+------------+-------------------+---------+---------+
| peer netns | IFLA_LINK_NETNSID | src_net | dev_net |
+------------+-------------------+---------+---------+
| | absent | source | target |
| absent +-------------------+---------+---------+
| | present | link | link |
+------------+-------------------+---------+---------+
| | absent | peer | target |
| present +-------------------+---------+---------+
| | present | peer | link |
+------------+-------------------+---------+---------+
When IFLA_LINK_NETNSID is present, the device is created in link netns
first and then moved to target netns. This has some side effects,
including extra ifindex allocation, ifname validation and link events.
These could be avoided if we create it in target netns from
the beginning.
On the other hand, the meaning of src_net parameter is ambiguous. It
varies depending on how parameters are passed. It is the effective
link (or peer netns) by design, but some drivers ignore it and use
dev_net instead.
To provide more netns context for drivers, this patch packs existing
newlink() parameters, along with the source netns, link netns and peer
netns, into a struct. The old "src_net" is renamed to "net" to avoid
confusion with real source netns, and will be deprecated later. The use
of src_net are converted to params->net trivially.
Signed-off-by: Xiao Liang <shaw.leon@gmail.com>
Reviewed-by: Kuniyuki Iwashima <kuniyu@amazon.com>
Link: https://patch.msgid.link/20250219125039.18024-3-shaw.leon@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
The OEM SFP-2.5G-BX10-D/U SFP module pair is meant to operate with
2500Base-X. However, in their EEPROM they incorrectly specify:
Transceiver codes : 0x00 0x12 0x00 0x00 0x12 0x00 0x01 0x05 0x00
BR, Nominal : 2500MBd
Use sfp_quirk_2500basex for this module to allow 2500Base-X mode anyway.
Tested on BananaPi R3.
Signed-off-by: Birger Koblitz <mail@birger-koblitz.de>
Reviewed-by: Daniel Golle <daniel@makrotopia.org>
Link: https://patch.msgid.link/20250218-b4-lkmsub-v1-1-1e51dcabed90@birger-koblitz.de
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
A previous patch introduces a build-time warning when CONFIG_DCB
is disabled:
drivers/net/ethernet/marvell/octeontx2/nic/otx2_pf.c: In function 'otx2_probe':
drivers/net/ethernet/marvell/octeontx2/nic/otx2_pf.c:3217:1: error: label 'err_free_zc_bmap' defined but not used [-Werror=unused-label]
drivers/net/ethernet/marvell/octeontx2/nic/otx2_vf.c: In function 'otx2vf_probe':
drivers/net/ethernet/marvell/octeontx2/nic/otx2_vf.c:740:1: error: label 'err_free_zc_bmap' defined but not used [-Werror=unused-label]
Add the same #ifdef check around it.
Fixes: efabce290151 ("octeontx2-pf: AF_XDP zero copy receive support")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: Suman Ghosh <sumang@marvell.com>
Link: https://patch.msgid.link/20250219162239.1376865-1-arnd@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Correct the hardware revision check comment in the QT2025 driver. The
revision value was documented as 0x3b instead of the correct 0xb3,
which matches the actual comparison logic in the code.
Reviewed-by: FUJITA Tomonori <fujita.tomonori@gmail.com>
Signed-off-by: Charalampos Mitrodimas <charmitro@posteo.net>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Trevor Gross <tmgross@umich.edu>
Link: https://patch.msgid.link/20250219-qt2025-comment-fix-v2-1-029f67696516@posteo.net
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
The function ext_requested() serves two distinct purposes: it checks
if extended link modes were requested, and it selects whether to use
extended or legacy link modes.
This change separates these two purposes. Now, ext_link_mode_requested()
is used directly for checking if extended link modes are requested,
while the selection of extended modes is handled independently based on
the autonegotiation status.
By making this distinction, the logic for determining whether to select
extended or legacy link modes is clearer.
Signed-off-by: Shahar Shitrit <shshitrit@nvidia.com>
Reviewed-by: Carolina Jubran <cjubran@nvidia.com>
Signed-off-by: Tariq Toukan <tariqt@nvidia.com>
Link: https://patch.msgid.link/20250219114112.403808-6-tariqt@nvidia.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
eth_proto_cap parameter represents the supported link modes,
while eth_proto_admin refers to the configured ones.
The function get_advertising() retrieves the configured link
modes, thus we update its parameter name to eth_proto_admin.
Signed-off-by: Shahar Shitrit <shshitrit@nvidia.com>
Reviewed-by: Carolina Jubran <cjubran@nvidia.com>
Signed-off-by: Tariq Toukan <tariqt@nvidia.com>
Link: https://patch.msgid.link/20250219114112.403808-5-tariqt@nvidia.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
The functions ptys2ethtool_supported_link(), ptys2ethtool_adver_link()
share the same code, thus, in order to remove code duplication we
introduce a new function ptys2ethtool_process_link() to handle the
processing of both supported and advertised link modes.
Signed-off-by: Shahar Shitrit <shshitrit@nvidia.com>
Reviewed-by: Carolina Jubran <cjubran@nvidia.com>
Signed-off-by: Tariq Toukan <tariqt@nvidia.com>
Link: https://patch.msgid.link/20250219114112.403808-4-tariqt@nvidia.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
The function ptys2ethtool_adver_link() contains duplicated code that
is found in mlx5e_ethtool_get_speed_arr().
To eliminate this redundancy, we update mlx5e_ethtool_get_speed_arr()
to select the appropriate table based on the ext argument passed by
the caller, rather than querying the supported mode locally.
This allows us to replace the current logic in ptys2ethtool_adver_link()
with a call to mlx5e_ethtool_get_speed_arr().
This adjustment aligns with the ptys2ethtool_supported_link() function
and prepares for an upcoming patch that reduces code duplication.
Signed-off-by: Shahar Shitrit <shshitrit@nvidia.com>
Reviewed-by: Carolina Jubran <cjubran@nvidia.com>
Signed-off-by: Tariq Toukan <tariqt@nvidia.com>
Link: https://patch.msgid.link/20250219114112.403808-3-tariqt@nvidia.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
The implication of the previous help text was that without this option
enabled, representor devices couldn't be added to a bridge device, while
in fact that was possible, just that rules didn't get offloaded to hw.
This commit clarifies the help text.
Signed-off-by: Cosmin Ratiu <cratiu@nvidia.com>
Reviewed-by: Dragos Tatulea <dtatulea@nvidia.com>
Signed-off-by: Tariq Toukan <tariqt@nvidia.com>
Link: https://patch.msgid.link/20250219114112.403808-2-tariqt@nvidia.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Loongson's DWMAC device may take nearly two seconds to complete DMA reset,
however, the default waiting time for reset is 200 milliseconds.
Therefore, the following error message may appear:
[14.427169] dwmac-loongson-pci 0000:00:03.2: Failed to reset the dma
Fixes: 803fc61df261 ("net: stmmac: dwmac-loongson: Add Loongson Multi-channels GMAC support")
Cc: stable@vger.kernel.org
Signed-off-by: Qunqin Zhao <zhaoqunqin@loongson.cn>
Reviewed-by: Huacai Chen <chenhuacai@loongson.cn>
Reviewed-by: Jacob Keller <jacob.e.keller@intel.com>
Acked-by: Yanteng Si <si.yanteng@linux.dev>
Link: https://patch.msgid.link/20250219020701.15139-1-zhaoqunqin@loongson.cn
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Enable Launch Time Control (LTC) support for XDP zero copy via XDP Tx
metadata framework.
This patch has been tested with tools/testing/selftests/bpf/xdp_hw_metadata
on Intel I225-LM Ethernet controller. Below are the test steps and result.
Test 1: Send a single packet with the launch time set to 1 s in the future.
Test steps:
1. On the DUT, start the xdp_hw_metadata selftest application:
$ sudo ./xdp_hw_metadata enp2s0 -l 1000000000 -L 1
2. On the Link Partner, send a UDP packet with VLAN priority 1 to port 9091
of the DUT.
Result:
When the launch time is set to 1 s in the future, the delta between the
launch time and the transmit hardware timestamp is 0.016 us, as shown in
printout of the xdp_hw_metadata application below.
0x562ff5dc8880: rx_desc[4]->addr=84110 addr=84110 comp_addr=84110 EoP
rx_hash: 0xE343384 with RSS type:0x1
HW RX-time: 1734578015467548904 (sec:1734578015.4675)
delta to User RX-time sec:0.0002 (183.103 usec)
XDP RX-time: 1734578015467651698 (sec:1734578015.4677)
delta to User RX-time sec:0.0001 (80.309 usec)
No rx_vlan_tci or rx_vlan_proto, err=-95
0x562ff5dc8880: ping-pong with csum=561c (want c7dd)
csum_start=34 csum_offset=6
HW RX-time: 1734578015467548904 (sec:1734578015.4675)
delta to HW Launch-time sec:1.0000 (1000000.000 usec)
0x562ff5dc8880: complete tx idx=4 addr=4018
HW Launch-time: 1734578016467548904 (sec:1734578016.4675)
delta to HW TX-complete-time sec:0.0000 (0.016 usec)
HW TX-complete-time: 1734578016467548920 (sec:1734578016.4675)
delta to User TX-complete-time sec:0.0000
(32.546 usec)
XDP RX-time: 1734578015467651698 (sec:1734578015.4677)
delta to User TX-complete-time sec:0.9999
(999929.768 usec)
HW RX-time: 1734578015467548904 (sec:1734578015.4675)
delta to HW TX-complete-time sec:1.0000 (1000000.016 usec)
0x562ff5dc8880: complete rx idx=132 addr=84110
Test 2: Send 1000 packets with a 10 ms interval and the launch time set to
500 us in the future.
Test steps:
1. On the DUT, start the xdp_hw_metadata selftest application:
$ sudo chrt -f 99 ./xdp_hw_metadata enp2s0 -l 500000 -L 1 > \
/dev/shm/result.log
2. On the Link Partner, send 1000 UDP packets with a 10 ms interval and
VLAN priority 1 to port 9091 of the DUT.
Result:
When the launch time is set to 500 us in the future, the average delta
between the launch time and the transmit hardware timestamp is 0.016 us,
as shown in the analysis of /dev/shm/result.log below. The XDP launch time
works correctly in sending 1000 packets continuously.
Min delta: 0.005 us
Avr delta: 0.016 us
Max delta: 0.031 us
Total packets forwarded: 1000
Signed-off-by: Song Yoong Siang <yoong.siang.song@intel.com>
Signed-off-by: Martin KaFai Lau <martin.lau@kernel.org>
Reviewed-by: Faizal Rahim <faizal.abdul.rahim@linux.intel.com>
Reviewed-by: Maciej Fijalkowski <maciej.fijalkowski@intel.com>
Link: https://patch.msgid.link/20250216093430.957880-6-yoong.siang.song@intel.com
|
|
Refactor the code for inserting an empty frame into a new function
igc_insert_empty_frame(). This change extracts the logic for inserting
an empty packet from igc_xmit_frame_ring() into a separate function,
allowing it to be reused in future implementations, such as the XDP
zero copy transmit function.
Remove the igc_desc_unused() checking in igc_init_tx_empty_descriptor()
because the number of descriptors needed is guaranteed.
Ensure that skb allocation and DMA mapping work for the empty frame,
before proceeding to fill in igc_tx_buffer info, context descriptor,
and data descriptor.
Rate limit the error messages for skb allocation and DMA mapping failures.
Update the comment to indicate that the 2 descriptors needed by the empty
frame are already taken into consideration in igc_xmit_frame_ring().
Handle the case where the insertion of an empty frame fails and explain
the reason behind this handling.
Signed-off-by: Song Yoong Siang <yoong.siang.song@intel.com>
Signed-off-by: Martin KaFai Lau <martin.lau@kernel.org>
Reviewed-by: Faizal Rahim <faizal.abdul.rahim@linux.intel.com>
Reviewed-by: Maciej Fijalkowski <maciej.fijalkowski@intel.com>
Link: https://patch.msgid.link/20250216093430.957880-5-yoong.siang.song@intel.com
|
|
Enable launch time (Time-Based Scheduling) support for XDP zero copy via
the XDP Tx metadata framework.
This patch has been tested with tools/testing/selftests/bpf/xdp_hw_metadata
on Intel Tiger Lake platform. Below are the test steps and result.
Test 1: Send a single packet with the launch time set to 1 s in the future.
Test steps:
1. On the DUT, start the xdp_hw_metadata selftest application:
$ sudo ./xdp_hw_metadata enp0s30f4 -l 1000000000 -L 1
2. On the Link Partner, send a UDP packet with VLAN priority 1 to port 9091
of the DUT.
Result:
When the launch time is set to 1 s in the future, the delta between the
launch time and the transmit hardware timestamp is 16.963 us, as shown in
printout of the xdp_hw_metadata application below.
0x55b5864717a8: rx_desc[4]->addr=88100 addr=88100 comp_addr=88100 EoP
No rx_hash, err=-95
HW RX-time: 1734579065767717328 (sec:1734579065.7677)
delta to User RX-time sec:0.0004 (375.624 usec)
XDP RX-time: 1734579065768004454 (sec:1734579065.7680)
delta to User RX-time sec:0.0001 (88.498 usec)
No rx_vlan_tci or rx_vlan_proto, err=-95
0x55b5864717a8: ping-pong with csum=5619 (want 0000)
csum_start=34 csum_offset=6
HW RX-time: 1734579065767717328 (sec:1734579065.7677)
delta to HW Launch-time sec:1.0000 (1000000.000 usec)
0x55b5864717a8: complete tx idx=4 addr=4018
HW Launch-time: 1734579066767717328 (sec:1734579066.7677)
delta to HW TX-complete-time sec:0.0000 (16.963 usec)
HW TX-complete-time: 1734579066767734291 (sec:1734579066.7677)
delta to User TX-complete-time sec:0.0001
(130.408 usec)
XDP RX-time: 1734579065768004454 (sec:1734579065.7680)
delta to User TX-complete-time sec:0.9999
(999860.245 usec)
HW RX-time: 1734579065767717328 (sec:1734579065.7677)
delta to HW TX-complete-time sec:1.0000 (1000016.963 usec)
0x55b5864717a8: complete rx idx=132 addr=88100
Test 2: Send 1000 packets with a 10 ms interval and the launch time set to
500 us in the future.
Test steps:
1. On the DUT, start the xdp_hw_metadata selftest application:
$ sudo chrt -f 99 ./xdp_hw_metadata enp0s30f4 -l 500000 -L 1 > \
/dev/shm/result.log
2. On the Link Partner, send 1000 UDP packets with a 10 ms interval and
VLAN priority 1 to port 9091 of the DUT.
Result:
When the launch time is set to 500 us in the future, the average delta
between the launch time and the transmit hardware timestamp is 13.854 us,
as shown in the analysis of /dev/shm/result.log below. The XDP launch time
works correctly in sending 1000 packets continuously.
Min delta: 08.410 us
Avr delta: 13.854 us
Max delta: 17.076 us
Total packets forwarded: 1000
Signed-off-by: Song Yoong Siang <yoong.siang.song@intel.com>
Signed-off-by: Martin KaFai Lau <martin.lau@kernel.org>
Reviewed-by: Choong Yong Liang <yong.liang.choong@linux.intel.com>
Link: https://patch.msgid.link/20250216093430.957880-4-yoong.siang.song@intel.com
|
|
Add ethtool support to configure the IRQ coalescing behavior. Support
separate timers for Rx and Tx for time based coalescing. For frame based
configuration, currently we only support the Rx side.
The hardware allows configuration of descriptor count instead of frame
count requiring conversion between the two. We assume 2 descriptors
per frame, one for the metadata and one for the data segment.
When rx-frames are not configured, we set the RX descriptor count to
half the ring size as a fail safe.
Default configuration:
ethtool -c eth0 | grep -E "rx-usecs:|tx-usecs:|rx-frames:"
rx-usecs: 30
rx-frames: 0
tx-usecs: 35
IRQ rate test:
With single iperf flow we monitor IRQ rate while changing the tx-usesc and
rx-usecs to high and low values.
ethtool -C eth0 rx-frames 8192 rx-usecs 150 tx-usecs 150
irq/sec 13k
irq/sec 14k
irq/sec 14k
ethtool -C eth0 rx-frames 8192 rx-usecs 10 tx-usecs 10
irq/sec 27k
irq/sec 28k
irq/sec 28k
Validating the use of extack:
ethtool -C eth0 rx-frames 16384
netlink error: fbnic: rx_frames is above device max
netlink error: Invalid argument
Signed-off-by: Mohsin Bashir <mohsin.bashr@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Brett Creeley <brett.creeley@amd.com>
Reviewed-by: Kalesh AP <kalesh-anakkur.purayil@broadcom.com>
Link: https://patch.msgid.link/20250218023520.2038010-1-mohsin.bashr@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Implement support for generating a 1pps output signal on SDP0.
And support custom firmware to output TOD.
Signed-off-by: Jiawen Wu <jiawenwu@trustnetic.com>
Link: https://patch.msgid.link/20250218023432.146536-5-jiawenwu@trustnetic.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Implement watchdog task to detect SYSTIME overflow and error cases of
Rx/Tx timestamp.
Signed-off-by: Jiawen Wu <jiawenwu@trustnetic.com>
Reviewed-by: Vadim Fedorenko <vadim.fedorenko@linux.dev>
Link: https://patch.msgid.link/20250218023432.146536-4-jiawenwu@trustnetic.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Implement the function get_ts_info and get_ts_stats in ethtool_ops to
get the HW capabilities and statistics for timestamping.
Signed-off-by: Jiawen Wu <jiawenwu@trustnetic.com>
Reviewed-by: Vadim Fedorenko <vadim.fedorenko@linux.dev>
Link: https://patch.msgid.link/20250218023432.146536-3-jiawenwu@trustnetic.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Implement support for PTP clock on Wangxun NICs.
Signed-off-by: Jiawen Wu <jiawenwu@trustnetic.com>
Reviewed-by: Vadim Fedorenko <vadim.fedorenko@linux.dev>
Link: https://patch.msgid.link/20250218023432.146536-2-jiawenwu@trustnetic.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
tun simply advances iov_iter when it needs to pad virtio header,
which leaves the garbage in the buffer as is. This will become
especially problematic when tun starts to allow enabling the hash
reporting feature; even if the feature is enabled, the packet may lack a
hash value and may contain a hole in the virtio header because the
packet arrived before the feature gets enabled or does not contain the
header fields to be hashed. If the hole is not filled with zero, it is
impossible to tell if the packet lacks a hash value.
In theory, a user of tun can fill the buffer with zero before calling
read() to avoid such a problem, but leaving the garbage in the buffer is
awkward anyway so replace advancing the iterator with writing zeros.
A user might have initialized the buffer to some non-zero value,
expecting tun to skip writing it. As this was never a documented
feature, this seems unlikely.
The overhead of filling the hole in the header is negligible when the
header size is specified according to the specification as doing so will
not make another cache line dirty under a reasonable assumption. Below
is a proof of this statement:
The first 10 bytes of the header is always written and tun also writes
the packet itself immediately after the packet unless the packet is
empty. This makes a hole between these writes whose size is: sz - 10
where sz is the specified header size.
Therefore, we will never make another cache line dirty when:
sz < L1_CACHE_BYTES + 10
where L1_CACHE_BYTES is the cache line size. Assuming
L1_CACHE_BYTES >= 16, this inequation holds when: sz < 26.
sz <= 20 according to the current specification so we even have a
margin of 5 bytes in case that the header size grows in a future version
of the specification.
Signed-off-by: Akihiko Odaki <akihiko.odaki@daynix.com>
Link: https://patch.msgid.link/20250215-buffers-v2-1-1fbc6aaf8ad6@daynix.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
While setting the DAC value, the wrong boolean value is evaluated to set
the DSP bias current. So let's correct the conditional statement and use
the right boolean value read from the DTS set in the priv.
Cc: stable@vger.kernel.org
Fixes: d1cb613efbd3 ("net: phy: qcom: add support for QCA807x PHY Family")
Signed-off-by: George Moussalem <george.moussalem@outlook.com>
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://patch.msgid.link/20250219130923.7216-1-ansuelsmth@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
The netdevsim driver was experiencing NOHZ tick-stop errors during packet
transmission due to pending softirq work when calling napi_schedule().
This issue was observed when running the netconsole selftest, which
triggered the following error message:
NOHZ tick-stop error: local softirq work is pending, handler #08!!!
To fix this issue, introduce a timer that schedules napi_schedule()
from a timer context instead of calling it directly from the TX path.
Create an hrtimer for each queue and kick it from the TX path,
which then schedules napi_schedule() from the timer context.
Suggested-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Breno Leitao <leitao@debian.org>
Link: https://patch.msgid.link/20250219-netdevsim-v3-1-811e2b8abc4c@debian.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Cross-merge networking fixes after downstream PR (net-6.14-rc4).
No conflicts or adjacent changes.
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/mkl/linux-can-next
Marc Kleine-Budde says:
====================
pull-request: can-next 2025-02-19
this is a pull request of 12 patches for net-next/master.
The first 4 patches are by Krzysztof Kozlowski and simplify the c_can
driver's c_can_plat_probe() function.
Ciprian Marian Costea contributes 3 patches to add S32G2/S32G3 support
to the flexcan driver.
Ruffalo Lavoisier's patch removes a duplicated word from the mcp251xfd
DT bindings documentation.
Oleksij Rempel extends the J1939 documentation.
The next patch is by Oliver Hartkopp and adds access for the Remote
Request Substitution bit in CAN-XL frames.
Henrik Brix Andersen's patch for the gs_usb driver adds support for
the CANnectivity firmware.
The last patch is by Robin van der Gracht and removes a duplicated
setup of RX FIFO in the rockchip_canfd driver.
linux-can-next-for-6.15-20250219
* tag 'linux-can-next-for-6.15-20250219' of git://git.kernel.org/pub/scm/linux/kernel/git/mkl/linux-can-next:
can: rockchip_canfd: rkcanfd_chip_fifo_setup(): remove duplicated setup of RX FIFO
can: gs_usb: add VID/PID for the CANnectivity firmware
can: canxl: support Remote Request Substitution bit access
can: j1939: Extend stack documentation with buffer size behavior
dt-binding: can: mcp251xfd: remove duplicate word
can: flexcan: add NXP S32G2/S32G3 SoC support
can: flexcan: Add quirk to handle separate interrupt lines for mailboxes
dt-bindings: can: fsl,flexcan: add S32G2/S32G3 SoC support
can: c_can: Use syscon_regmap_lookup_by_phandle_args
can: c_can: Use of_property_present() to test existence of DT property
can: c_can: Simplify handling syscon error path
can: c_can: Drop useless final probe failure message
====================
Link: https://patch.msgid.link/20250219113354.529611-1-mkl@pengutronix.de
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
Add check for the return value of nfp_app_ctrl_msg_alloc() in
nfp_bpf_cmsg_alloc() to prevent null pointer dereference.
Fixes: ff3d43f7568c ("nfp: bpf: implement helpers for FW map ops")
Cc: stable@vger.kernel.org
Signed-off-by: Haoxiang Li <haoxiang_li2024@163.com>
Link: https://patch.msgid.link/20250218030409.2425798-1-haoxiang_li2024@163.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
The external PHY will undergo a soft reset twice during the resume process
when it wake up from suspend. The first reset occurs when the axienet
driver calls phylink_of_phy_connect(), and the second occurs when
mdio_bus_phy_resume() invokes phy_init_hw(). The second soft reset of the
external PHY does not reinitialize the internal PHY, which causes issues
with the internal PHY, resulting in the PHY link being down. To prevent
this, setting the mac_managed_pm flag skips the mdio_bus_phy_resume()
function.
Fixes: a129b41fe0a8 ("Revert "net: phy: dp83867: perform soft reset and retain established link"")
Signed-off-by: Nick Hu <nick.hu@sifive.com>
Reviewed-by: Jacob Keller <jacob.e.keller@intel.com>
Link: https://patch.msgid.link/20250217055843.19799-1-nick.hu@sifive.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
priv->plat->fix_mac_speed() is called from stmmac_mac_link_up(), which
is passed the speed as an "int". However, fix_mac_speed() implicitly
casts this to an unsigned int. Some platform glue code print this value
using %u, others with %d. Some implicitly cast it back to an int, and
others to u32.
Good practice is to use one type and only one type to represent a value
being passed around a driver.
Switch all of these over to consistently use "int" when dealing with a
speed passed from stmmac_mac_link_up(), even though the speed will
always be positive.
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Acked-by: Chen-Yu Tsai <wens@csie.org>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Acked-by: Nobuhiro Iwamatsu <nobuhiro1.iwamatsu@toshiba.co.jp>
Link: https://patch.msgid.link/E1tkKmN-004ObM-Ge@rmk-PC.armlinux.org.uk
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
priv->flow_ctrl is only accessed by stmmac_main.c, and the only place
that it is read is in stmmac_mac_flow_ctrl(). This function is only
called from stmmac_mac_link_up() which always sets priv->flow_ctrl
immediately before calling this function.
Therefore, initialising this at probe time is ineffectual because it
will always be overwritten before it's read. As such, the "flow_ctrl"
module parameter has been useless for some time. Rather than remove
the module parameter, which would risk module load failure, change the
description to indicate that it is obsolete, and warn if it is set by
userspace.
Moreover, storing the value in the stmmac_priv has no benefit as it's
set and then immediately read stmmac_mac_flow_ctrl(). Instead, pass it
as a parameter to this function..
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Nobuhiro Iwamatsu <nobuhiro1.iwamatsu@toshiba.co.jp>
Link: https://patch.msgid.link/E1tkKmI-004ObG-DL@rmk-PC.armlinux.org.uk
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
priv->pause corresponds with "pause_time" in the 802.3 specification,
and is also called "pause_time" in the various MAC backends. For
consistency, use the same name in the core stmmac code.
Clarify the units of the "pause" module parameter which sets up this
struct member to indicate that it's in units of the pause_quanta
defined by 802.3, which is 512 bit times.
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Reviewed-by: Mateusz Polchlopek <mateusz.polchlopek@intel.com>
Link: https://patch.msgid.link/E1tkKmD-004ObA-9K@rmk-PC.armlinux.org.uk
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Add more logs to assist in debugging and monitoring
driver behaviour, making it easier to identify potential
issues during development and testing.
Signed-off-by: Erni Sri Satya Vennela <ernis@linux.microsoft.com>
Reviewed-by: Haiyang Zhang <haiyangz@microsoft.com>
Link: https://patch.msgid.link/1739842455-23899-1-git-send-email-ernis@linux.microsoft.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
