| Age | Commit message (Collapse) | Author |
|---|
|
The masks in priv->clk_25m_reg and priv->clk_25m_mask are one-bits-set
for the values that comprise the fields, not zero-bits-set.
This patch fixes the clock frequency configuration for ATH8030 and
ATH8035 Atheros PHYs by removing the erroneous "~".
To reproduce this bug, configure the PHY with the device tree binding
"qca,clk-out-frequency" and remove the machine specific PHY fixups.
Fixes: 2f664823a47021 ("net: phy: at803x: add device tree binding")
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Reported-by: Russell King <rmk+kernel@armlinux.org.uk>
Reviewed-by: Russell King <rmk+kernel@armlinux.org.uk>
Tested-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Perform missing MQPRIO resource cleanup in PCI shutdown path. Also,
fix MQPRIO MSIX bitmap leak in resource cleanup.
Fixes: b1396c2bd675 ("cxgb4: parse and configure TC-MQPRIO offload")
Signed-off-by: Rahul Lakkireddy <rahul.lakkireddy@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
cxgb4_update_mac_filt() earlier requests firmware to add a new MAC
address into MPS TCAM. The MPS TCAM index returned by firmware is
stored in pi->xact_addr_filt. However, the saved MPS TCAM index gets
overwritten again with the return value of cxgb4_update_mac_filt(),
which is wrong.
When trying to update to another MAC address later, the wrong MPS TCAM
index is sent to firmware, which causes firmware to return error,
because it's not the same MPS TCAM index that firmware had sent
earlier to driver.
So, fix by removing the wrong overwrite being done after call to
cxgb4_update_mac_filt().
Fixes: 3f8cfd0d95e6 ("cxgb4/cxgb4vf: Program hash region for {t4/t4vf}_change_mac()")
Signed-off-by: Herat Ramani <herat@chelsio.com>
Signed-off-by: Rahul Lakkireddy <rahul.lakkireddy@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Currently, CONFIG_VHOST depends on CONFIG_VIRTUALIZATION. But vhost is
not necessarily for VM since it's a generic userspace and kernel
communication protocol. Such dependency may prevent archs without
virtualization support from using vhost.
To solve this, a dedicated vhost menu is created under drivers so
CONIFG_VHOST can be decoupled out of CONFIG_VIRTUALIZATION.
While at it, also squash Kconfig.vringh into vhost Kconfig file. This
avoids the trick of conditional inclusion from VOP or CAIF. Then it
will be easier to introduce new vringh users and common dependency for
both vringh and vhost.
Signed-off-by: Jason Wang <jasowang@redhat.com>
Link: https://lore.kernel.org/r/20200326140125.19794-2-jasowang@redhat.com
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
|
|
Pull networking updates from David Miller:
"Highlights:
1) Fix the iwlwifi regression, from Johannes Berg.
2) Support BSS coloring and 802.11 encapsulation offloading in
hardware, from John Crispin.
3) Fix some potential Spectre issues in qtnfmac, from Sergey
Matyukevich.
4) Add TTL decrement action to openvswitch, from Matteo Croce.
5) Allow paralleization through flow_action setup by not taking the
RTNL mutex, from Vlad Buslov.
6) A lot of zero-length array to flexible-array conversions, from
Gustavo A. R. Silva.
7) Align XDP statistics names across several drivers for consistency,
from Lorenzo Bianconi.
8) Add various pieces of infrastructure for offloading conntrack, and
make use of it in mlx5 driver, from Paul Blakey.
9) Allow using listening sockets in BPF sockmap, from Jakub Sitnicki.
10) Lots of parallelization improvements during configuration changes
in mlxsw driver, from Ido Schimmel.
11) Add support to devlink for generic packet traps, which report
packets dropped during ACL processing. And use them in mlxsw
driver. From Jiri Pirko.
12) Support bcmgenet on ACPI, from Jeremy Linton.
13) Make BPF compatible with RT, from Thomas Gleixnet, Alexei
Starovoitov, and your's truly.
14) Support XDP meta-data in virtio_net, from Yuya Kusakabe.
15) Fix sysfs permissions when network devices change namespaces, from
Christian Brauner.
16) Add a flags element to ethtool_ops so that drivers can more simply
indicate which coalescing parameters they actually support, and
therefore the generic layer can validate the user's ethtool
request. Use this in all drivers, from Jakub Kicinski.
17) Offload FIFO qdisc in mlxsw, from Petr Machata.
18) Support UDP sockets in sockmap, from Lorenz Bauer.
19) Fix stretch ACK bugs in several TCP congestion control modules,
from Pengcheng Yang.
20) Support virtual functiosn in octeontx2 driver, from Tomasz
Duszynski.
21) Add region operations for devlink and use it in ice driver to dump
NVM contents, from Jacob Keller.
22) Add support for hw offload of MACSEC, from Antoine Tenart.
23) Add support for BPF programs that can be attached to LSM hooks,
from KP Singh.
24) Support for multiple paths, path managers, and counters in MPTCP.
From Peter Krystad, Paolo Abeni, Florian Westphal, Davide Caratti,
and others.
25) More progress on adding the netlink interface to ethtool, from
Michal Kubecek"
* git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net-next: (2121 commits)
net: ipv6: rpl_iptunnel: Fix potential memory leak in rpl_do_srh_inline
cxgb4/chcr: nic-tls stats in ethtool
net: dsa: fix oops while probing Marvell DSA switches
net/bpfilter: remove superfluous testing message
net: macb: Fix handling of fixed-link node
net: dsa: ksz: Select KSZ protocol tag
netdevsim: dev: Fix memory leak in nsim_dev_take_snapshot_write
net: stmmac: add EHL 2.5Gbps PCI info and PCI ID
net: stmmac: add EHL PSE0 & PSE1 1Gbps PCI info and PCI ID
net: stmmac: create dwmac-intel.c to contain all Intel platform
net: dsa: bcm_sf2: Support specifying VLAN tag egress rule
net: dsa: bcm_sf2: Add support for matching VLAN TCI
net: dsa: bcm_sf2: Move writing of CFP_DATA(5) into slicing functions
net: dsa: bcm_sf2: Check earlier for FLOW_EXT and FLOW_MAC_EXT
net: dsa: bcm_sf2: Disable learning for ASP port
net: dsa: b53: Deny enslaving port 7 for 7278 into a bridge
net: dsa: b53: Prevent tagged VLAN on port 7 for 7278
net: dsa: b53: Restore VLAN entries upon (re)configuration
net: dsa: bcm_sf2: Fix overflow checks
hv_netvsc: Remove unnecessary round_up for recv_completion_cnt
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/masahiroy/linux-kbuild
Pull Kbuild updates from Masahiro Yamada:
"Build system:
- add CONFIG_UNUSED_KSYMS_WHITELIST, which will be useful to define a
fixed set of export symbols for Generic Kernel Image (GKI)
- allow to run 'make dt_binding_check' without .config
- use full schema for checking DT examples in *.yaml files
- make modpost fail for missing MODULE_IMPORT_NS(), which makes more
sense because we know the produced modules are never loadable
- Remove unused 'AS' variable
Kconfig:
- sanitize DEFCONFIG_LIST, and remove ARCH_DEFCONFIG from Kconfig
files
- relax the 'imply' behavior so that symbols implied by 'y' can
become 'm'
- make 'imply' obey 'depends on' in order to make 'imply' really weak
Misc:
- add documentation on building the kernel with Clang/LLVM
- revive __HAVE_ARCH_STRLEN for 32bit sparc to use optimized strlen()
- fix warning from deb-pkg builds when CONFIG_DEBUG_INFO=n
- various script and Makefile cleanups"
* tag 'kbuild-v5.7' of git://git.kernel.org/pub/scm/linux/kernel/git/masahiroy/linux-kbuild: (34 commits)
Makefile: Update kselftest help information
kbuild: deb-pkg: fix warning when CONFIG_DEBUG_INFO is unset
kbuild: add outputmakefile to no-dot-config-targets
kbuild: remove AS variable
net: wan: wanxl: refactor the firmware rebuild rule
net: wan: wanxl: use $(M68KCC) instead of $(M68KAS) for rebuilding firmware
net: wan: wanxl: use allow to pass CROSS_COMPILE_M68k for rebuilding firmware
kbuild: add comment about grouped target
kbuild: add -Wall to KBUILD_HOSTCXXFLAGS
kconfig: remove unused variable in qconf.cc
sparc: revive __HAVE_ARCH_STRLEN for 32bit sparc
kbuild: refactor Makefile.dtbinst more
kbuild: compute the dtbs_install destination more simply
Makefile: disallow data races on gcc-10 as well
kconfig: make 'imply' obey the direct dependency
kconfig: allow symbols implied by y to become m
net: drop_monitor: use IS_REACHABLE() to guard net_dm_hw_report()
modpost: return error if module is missing ns imports and MODULE_ALLOW_MISSING_NAMESPACE_IMPORTS=n
modpost: rework and consolidate logging interface
kbuild: allow to run dt_binding_check without kernel configuration
...
|
|
Included nic tls statistics in ethtool stats.
Signed-off-by: Rohit Maheshwari <rohitm@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
fixed-link nodes are treated as PHY nodes by of_mdiobus_child_is_phy().
We must check if the interface is a fixed-link before looking up for PHY
nodes.
Fixes: 7897b071ac3b ("net: macb: convert to phylink")
Tested-by: Cristian Birsan <cristian.birsan@microchip.com>
Signed-off-by: Codrin Ciubotariu <codrin.ciubotariu@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
KSZ protocol tag is needed by the KSZ DSA drivers.
Fixes: 0b9f9dfbfab4 ("dsa: Allow tag drivers to be built as modules")
Tested-by: Cristian Birsan <cristian.birsan@microchip.com>
Signed-off-by: Codrin Ciubotariu <codrin.ciubotariu@microchip.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
|
|
In case memory resources for dummy_data were allocated, release them
before return.
Addresses-Coverity-ID: 1491997 ("Resource leak")
Fixes: 7ef19d3b1d5e ("devlink: report error once U32_MAX snapshot ids have been used")
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Reviewed-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add EHL SGMII 2.5Gbps PCI info and PCI ID
Signed-off-by: Voon Weifeng <weifeng.voon@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add EHL PSE0/1 RGMII & SGMII 1Gbps PCI info and PCI ID
Signed-off-by: Voon Weifeng <weifeng.voon@intel.com>
Signed-off-by: Ong Boon Leong <boon.leong.ong@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
As stmmac_pci.c file is getting bigger and more complex, it is reasonable
to separate all the Intel specific dwmac pci device to a different file.
This move includes Intel Quark, TGL and EHL. A new kernel config
CONFIG_DWMAC_INTEL is introduced and depends on X86. For this initial
patch, all the necessary function such as probe() and exit() are identical
besides the function name.
Signed-off-by: Voon Weifeng <weifeng.voon@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The port to which the ASP is connected on 7278 is not capable of
processing VLAN tags as part of the Ethernet frame, so allow an user to
configure the egress VLAN policy they want to see applied by purposing
the h_ext.data[1] field. Bit 0 is used to indicate that 0=tagged,
1=untagged.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Update relevant code paths to support the programming and matching of
VLAN TCI, this is the only member of the ethtool_flow_ext that we can
match, the switch does not permit matching the VLAN Ethernet Type field.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
In preparation for matching VLANs, move the writing of CFP_DATA(5) into
the IPv4 and IPv6 slicing logic since they are part of the per-flow
configuration.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
We do not currently support matching on FLOW_EXT or FLOW_MAC_EXT, but we
were not checking for those bits being set in the flow specification.
The check for FLOW_EXT and FLOW_MAC_EXT are separated out because a
subsequent commit will add support for matching VLAN TCI which are
covered by FLOW_EXT.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
We don't want to enable learning for the ASP port since it only receives
directed traffic, this allows us to bypass ARL-driven forwarding rules
which could conflict with Broadcom tags and/or CFP forwarding.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
On 7278, port 7 connects to the ASP which should only receive frames
through the use of CFP rules, it is not desirable to have it be part of
a bridge at all since that would make it pick up unwanted traffic that
it may not even be able to filter or sustain.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
On 7278, port 7 of the switch connects to the ASP UniMAC which is not
capable of processing VLAN tagged frames. We can still allow the port to
be part of a VLAN entry, and we may want it to be untagged on egress on
that VLAN because of that limitation.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The first time b53_configure_vlan() is called we have not configured any
VLAN entries yet, since that happens later when interfaces get brought
up. When b53_configure_vlan() is called again from suspend/resume we
need to restore all VLAN entries though.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Commit f949a12fd697 ("net: dsa: bcm_sf2: fix buffer overflow doing
set_rxnfc") tried to fix the some user controlled buffer overflows in
bcm_sf2_cfp_rule_set() and bcm_sf2_cfp_rule_del() but the fix was using
CFP_NUM_RULES, which while it is correct not to overflow the bitmaps, is
not representative of what the device actually supports. Correct that by
using bcm_sf2_cfp_rule_size() instead.
The latter subtracts the number of rules by 1, so change the checks from
greater than or equal to greater than accordingly.
Fixes: f949a12fd697 ("net: dsa: bcm_sf2: fix buffer overflow doing set_rxnfc")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The vzalloc_node(), already rounds the total size to whole pages, and
sizeof(u64) is smaller than sizeof(struct recv_comp_data). So
round_up of recv_completion_cnt is not necessary, and may cause extra
memory allocation.
To save memory, remove this unnecessary round_up for recv_completion_cnt.
Signed-off-by: Haiyang Zhang <haiyangz@microsoft.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Implement support for setting of packet trap group parameters by
invoking the trap_group_init() callback with the new parameters.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Reviewed-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Some packet traps are currently exposed to user space as being member of
"l3_drops" trap group, but internally they are member of a different
group.
Switch these traps to use the correct group so that they are all subject
to the same policer, as exposed to user space.
Set the trap priority of packets trapped due to loopback error during
routing to the lowest priority. Such packets are not routed again by the
kernel and therefore should not mask other traps (e.g., host miss) that
should be routed.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Reviewed-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The policer is now initialized as part of the registration with devlink,
so there is no need to initialize it before the registration.
Remove the initialization.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Reviewed-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Register supported packet trap policers with devlink and implement
callbacks to change their parameters and read their counters.
Prevent user space from passing invalid policer parameters down to the
device by checking their validity and communicating the failure via an
appropriate extack message.
v2:
* Remove the max/min validity checks from __mlxsw_sp_trap_policer_set()
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Reviewed-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Prepare an array of policer IDs to register with devlink and their
associated parameters.
The array is composed from both policers that are currently bound to
exposed trap groups and policers that are not bound to any trap group.
v2:
* Provide max/min rate/burst size when registering policers
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Reviewed-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
During initialization the driver configures various packet trap groups
and binds policers to them.
Currently, most of these groups are not exposed to user space and
therefore their policers should not be exposed as well. Otherwise, user
space will be able to alter policer parameters without knowing which
packet traps are policed by the policer.
Use a bitmap to track the used policer IDs so that these policers will
not be registered with devlink in a subsequent patch.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Reviewed-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The QoS Policer Configuration Register (QPCR) is used to configure
hardware policers. Extend this register with following fields and
defines which will be used by subsequent patches:
1. Violate counter: reads number of packets dropped by the policer
2. Clear counter: to ensure we start counting from 0
3. Rate and burst size limits
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Reviewed-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add a dummy callback to set trap group parameters. Return an error when
the 'fail_trap_group_set' debugfs file is set in order to exercise error
paths and verify that error is propagated to user space when should.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Reviewed-by: Jiri Pirko <jiri@mellanox.com>
Reviewed-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Packet trap groups are used to aggregate logically related packet traps.
Currently, these groups allow user space to batch operations such as
setting the trap action of all member traps.
In order to prevent the CPU from being overwhelmed by too many trapped
packets, it is desirable to bind a packet trap policer to these groups.
For example, to limit all the packets that encountered an exception
during routing to 10Kpps.
Allow device drivers to bind default packet trap policers to packet trap
groups when the latter are registered with devlink.
The next patch will enable user space to change this default binding.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Reviewed-by: Jiri Pirko <jiri@mellanox.com>
Reviewed-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Register three dummy packet trap policers with devlink and implement
callbacks to change their parameters and read their counters.
This will be used later on in the series to test the devlink-trap
policer infrastructure.
v2:
* Remove check about burst size being a power of 2 and instead add a
debugfs knob to fail the operation
* Provide max/min rate/burst size when registering policers and remove
the validity checks from nsim_dev_devlink_trap_policer_set()
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Reviewed-by: Jiri Pirko <jiri@mellanox.com>
Reviewed-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull locking updates from Ingo Molnar:
"The main changes in this cycle were:
- Continued user-access cleanups in the futex code.
- percpu-rwsem rewrite that uses its own waitqueue and atomic_t
instead of an embedded rwsem. This addresses a couple of
weaknesses, but the primary motivation was complications on the -rt
kernel.
- Introduce raw lock nesting detection on lockdep
(CONFIG_PROVE_RAW_LOCK_NESTING=y), document the raw_lock vs. normal
lock differences. This too originates from -rt.
- Reuse lockdep zapped chain_hlocks entries, to conserve RAM
footprint on distro-ish kernels running into the "BUG:
MAX_LOCKDEP_CHAIN_HLOCKS too low!" depletion of the lockdep
chain-entries pool.
- Misc cleanups, smaller fixes and enhancements - see the changelog
for details"
* 'locking-core-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (55 commits)
fs/buffer: Make BH_Uptodate_Lock bit_spin_lock a regular spinlock_t
thermal/x86_pkg_temp: Make pkg_temp_lock a raw_spinlock_t
Documentation/locking/locktypes: Minor copy editor fixes
Documentation/locking/locktypes: Further clarifications and wordsmithing
m68knommu: Remove mm.h include from uaccess_no.h
x86: get rid of user_atomic_cmpxchg_inatomic()
generic arch_futex_atomic_op_inuser() doesn't need access_ok()
x86: don't reload after cmpxchg in unsafe_atomic_op2() loop
x86: convert arch_futex_atomic_op_inuser() to user_access_begin/user_access_end()
objtool: whitelist __sanitizer_cov_trace_switch()
[parisc, s390, sparc64] no need for access_ok() in futex handling
sh: no need of access_ok() in arch_futex_atomic_op_inuser()
futex: arch_futex_atomic_op_inuser() calling conventions change
completion: Use lockdep_assert_RT_in_threaded_ctx() in complete_all()
lockdep: Add posixtimer context tracing bits
lockdep: Annotate irq_work
lockdep: Add hrtimer context tracing bits
lockdep: Introduce wait-type checks
completion: Use simple wait queues
sched/swait: Prepare usage in completions
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull power management updates from Rafael Wysocki:
"These clean up and rework the PM QoS API, address a suspend-to-idle
wakeup regression on some ACPI-based platforms, clean up and extend a
few cpuidle drivers, update multiple cpufreq drivers and cpufreq
documentation, and fix a number of issues in devfreq and several other
things all over.
Specifics:
- Clean up and rework the PM QoS API to simplify the code and reduce
the size of it (Rafael Wysocki).
- Fix a suspend-to-idle wakeup regression on Dell XPS13 9370 and
similar platforms where the USB plug/unplug events are handled by
the EC (Rafael Wysocki).
- CLean up the intel_idle and PSCI cpuidle drivers (Rafael Wysocki,
Ulf Hansson).
- Extend the haltpoll cpuidle driver so that it can be forced to run
on some systems where it refused to load (Maciej Szmigiero).
- Convert several cpufreq documents to the .rst format and move the
legacy driver documentation into one common file (Mauro Carvalho
Chehab, Rafael Wysocki).
- Update several cpufreq drivers:
* Extend and fix the imx-cpufreq-dt driver (Anson Huang).
* Improve the -EPROBE_DEFER handling and fix unwanted CPU
overclocking on i.MX6ULL in imx6q-cpufreq (Anson Huang,
Christoph Niedermaier).
* Add support for Krait based SoCs to the qcom driver (Ansuel
Smith).
* Add support for OPP_PLUS to ti-cpufreq (Lokesh Vutla).
* Add platform specific intermediate callbacks support to
cpufreq-dt and update the imx6q driver (Peng Fan).
* Simplify and consolidate some pieces of the intel_pstate
driver and update its documentation (Rafael Wysocki, Alex
Hung).
- Fix several devfreq issues:
* Remove unneeded extern keyword from a devfreq header file and
use the DEVFREQ_GOV_UPDATE_INTERNAL event name instead of
DEVFREQ_GOV_INTERNAL (Chanwoo Choi).
* Fix the handling of dev_pm_qos_remove_request() result
(Leonard Crestez).
* Use constant name for userspace governor (Pierre Kuo).
* Get rid of doc warnings and fix a typo (Christophe JAILLET).
- Use built-in RCU list checking in some places in the PM core to
avoid false-positive RCU usage warnings (Madhuparna Bhowmik).
- Add explicit READ_ONCE()/WRITE_ONCE() annotations to low-level PM
QoS routines (Qian Cai).
- Fix removal of wakeup sources to avoid NULL pointer dereferences in
a corner case (Neeraj Upadhyay).
- Clean up the handling of hibernate compat ioctls and fix the
related documentation (Eric Biggers).
- Update the idle_inject power capping driver to use variable-length
arrays instead of zero-length arrays (Gustavo Silva).
- Fix list format in a PM QoS document (Randy Dunlap).
- Make the cpufreq stats module use scnprintf() to avoid potential
buffer overflows (Takashi Iwai).
- Add pm_runtime_get_if_active() to PM-runtime API (Sakari Ailus).
- Allow no domain-idle-states DT property in generic PM domains (Ulf
Hansson).
- Fix a broken y-axis scale in the intel_pstate_tracer utility (Doug
Smythies)"
* tag 'pm-5.7-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm: (78 commits)
cpufreq: intel_pstate: Simplify intel_pstate_cpu_init()
tools/power/x86/intel_pstate_tracer: fix a broken y-axis scale
ACPI: PM: s2idle: Refine active GPEs check
ACPICA: Allow acpi_any_gpe_status_set() to skip one GPE
PM: sleep: wakeup: Skip wakeup_source_sysfs_remove() if device is not there
PM / devfreq: Get rid of some doc warnings
PM / devfreq: Fix handling dev_pm_qos_remove_request result
PM / devfreq: Fix a typo in a comment
PM / devfreq: Change to DEVFREQ_GOV_UPDATE_INTERVAL event name
PM / devfreq: Remove unneeded extern keyword
PM / devfreq: Use constant name of userspace governor
ACPI: PM: s2idle: Fix comment in acpi_s2idle_prepare_late()
cpufreq: qcom: Add support for krait based socs
cpufreq: imx6q-cpufreq: Improve the logic of -EPROBE_DEFER handling
cpufreq: Use scnprintf() for avoiding potential buffer overflow
cpuidle: psci: Split psci_dt_cpu_init_idle()
PM / Domains: Allow no domain-idle-states DT property in genpd when parsing
PM / hibernate: Remove unnecessary compat ioctl overrides
PM: hibernate: fix docs for ioctls that return loff_t via pointer
Documentation: intel_pstate: update links for references
...
|
|
Add a separate set of PCS operations, which MAC drivers can use to
couple phylink with their associated MAC PCS layer. The PCS
operations include:
- pcs_get_state() - reads the link up/down, resolved speed, duplex
and pause from the PCS.
- pcs_config() - configures the PCS for the specified mode, PHY
interface type, and setting the advertisement.
- pcs_an_restart() - restarts 802.3 in-band negotiation with the
link partner
- pcs_link_up() - informs the PCS that link has come up, and the
parameters of the link. Link parameters are used to program the
PCS for fixed speed and non-inband modes.
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Rename the bland 'ops' member of struct phylink to be a more
descriptive 'mac_ops' - this is necessary as we're about to introduce
another set of operations.
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Change phylink_mii_c22_pcs_set_advertisement() to take only the PHY
interface and advertisement mask, rather than the full phylink state.
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Factor out mapping the tx skb to a new function rtl8169_tx_map(). This
allows to remove redundancies, and rtl8169_get_txd_opts1() has only
one user left, so it can be inlined.
As a result rtl8169_xmit_frags() is significantly simplified, and in
rtl8169_start_xmit() the code is simplified and better readable.
No functional change intended.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The qed_chain data structure was modified in
commit 1a4a69751f4d ("qed: Chain support for external PBL") to support
receiving an external pbl (due to iWARP FW requirements).
The pages pointed to by the pbl are allocated in qed_chain_alloc
and their virtual address are stored in an virtual addresses array to
enable accessing and freeing the data. The physical addresses however
weren't stored and were accessed directly from the external-pbl
during free.
Destroy-qp flow, leads to freeing the external pbl before the chain is
freed, when the chain is freed it tries accessing the already freed
external pbl, leading to a use-after-free. Therefore we need to store
the physical addresses in additional to the virtual addresses in a
new data structure.
Fixes: 1a4a69751f4d ("qed: Chain support for external PBL")
Signed-off-by: Michal Kalderon <mkalderon@marvell.com>
Signed-off-by: Yuval Bason <ybason@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
If the mtu is greater than TD_MSS_MAX, then TSO is disabled, see
rtl8169_fix_features(). Because mss is less than mtu, we can't have
the case mss > TD_MSS_MAX in the TSO path.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch adds complete support for manipulating the L2 Policing Tables
from this switch. There are 45 table entries, one entry per each port
and traffic class, and one dedicated entry for broadcast traffic for
each ingress port.
Policing entries are shareable, and we use this functionality to support
shared block filters.
We are modeling broadcast policers as simple tc-flower matches on
dst_mac. As for the traffic class policers, the switch only deduces the
traffic class from the VLAN PCP field, so it makes sense to model this
as a tc-flower match on vlan_prio.
How to limit broadcast traffic coming from all front-panel ports to a
cumulated total of 10 Mbit/s:
tc qdisc add dev sw0p0 ingress_block 1 clsact
tc qdisc add dev sw0p1 ingress_block 1 clsact
tc qdisc add dev sw0p2 ingress_block 1 clsact
tc qdisc add dev sw0p3 ingress_block 1 clsact
tc filter add block 1 flower skip_sw dst_mac ff:ff:ff:ff:ff:ff \
action police rate 10mbit burst 64k
How to limit traffic with VLAN PCP 0 (also includes untagged traffic) to
100 Mbit/s on port 0 only:
tc filter add dev sw0p0 ingress protocol 802.1Q flower skip_sw \
vlan_prio 0 action police rate 100mbit burst 64k
The broadcast, VLAN PCP and port policers are compatible with one
another (can be installed at the same time on a port).
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This adds partial configuration support for the L2 Policing Table. Out
of the 45 policing entries, only 5 are used (one for each port), in a
shared manner. All 8 traffic classes, and the broadcast policer, are
redirected to a common instance which belongs to the ingress port.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch is a trivial passthrough towards the ocelot library, which
support port policers since commit 2c1d029a017f ("net: mscc: ocelot:
Implement port policers via tc command").
Some data structure conversion between the DSA core and the Ocelot
library is necessary, for policer parameters.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Ocelot has 384 policers that can be allocated to ingress ports,
QoS classes per port, and VCAP IS2 entries. ocelot_police.c
supports to set policers which can be allocated to police action
of VCAP IS2. We allocate policers from maximum pol_id, and
decrease the pol_id when add a new vcap_is2 entry which is
police action.
Signed-off-by: Xiaoliang Yang <xiaoliang.yang_1@nxp.com>
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When the FW RESET event comes to the driver from the firmware,
or the fw_status goes to 0 (stopped) or to 0xff (no PCI
connection), then shut down the driver activity. This event
signals a FW upgrade where we need to quiesce all operations and
wait for the FW to restart. The FW will continue the update
process once it sees all the LIFs are reset. When the update
process is done it will set the fw_status back to RUNNING.
Meanwhile, the heartbeat check continues and when the fw_status
is seen as set to running we can restart the driver operations.
Signed-off-by: Shannon Nelson <snelson@pensando.io>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When the link goes down, we need to disable the queues on the
NIC in addition to stopping the netdev stack. This lets the
FW know that the driver has stopped queue activity, and then
the FW can do internal reconfiguration work, whether actually
Link related, or for other internal FW needs. To do this,
we pull out the queue enable and disable from ionic_open()
and ionic_stop() so they can be used by other routines.
To help keep things sane, we swap the queue enables so that
the rx queue and its napi are enabled before the tx queue
which rides on the rx queues napi.
We also drop the ionic_lif_quiesce() as it doesn't do anything
more than what the queue disable has already taken care of.
Signed-off-by: Shannon Nelson <snelson@pensando.io>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Make sure the queue structures exist before trying
to delete them. This addresses a couple of error
recovery issues.
Signed-off-by: Shannon Nelson <snelson@pensando.io>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Clean out tx requests that didn't get finished before
shutting down the queue.
Signed-off-by: Shannon Nelson <snelson@pensando.io>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
