| Age | Commit message (Collapse) | Author |
|---|
|
When support for the MDB entries was added, the valid bit was correctly
changed to be assigned depending on the remaining port bitmask, that is,
if there were no more ports added to the entry's port bitmask, the entry
now becomes invalid. There was another assignment a few lines below that
would override this which would invalidate entries even when there were
still multiple ports left in the MDB entry.
Fixes: 5d65b64a3d97 ("net: dsa: b53: Add support for MDB")
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When VLAN is enabled, and an ARL search is issued, we also need to
compare the full {MAC,VID} tuple before returning a successful search
result.
Fixes: 1da6df85c6fb ("net: dsa: b53: Implement ARL add/del/dump operations")
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
To avoid a loop with qdiscs and xfrms, check if the skb has already gone
through the qdisc attached to the VRF device and then to the xfrm layer.
If so, no need for a second redirect.
Fixes: 193125dbd8eb ("net: Introduce VRF device driver")
Reported-by: Trev Larock <trev@larock.ca>
Signed-off-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
lan87xx_phy_init() initializes the lan87xx phy hardware
including its TC10 Wake-up and Sleep features.
Fixes: 3e50d2da5850 ("Add driver for Microchip LAN87XX T1 PHYs")
Signed-off-by: Yuiko Oshino <yuiko.oshino@microchip.com>
v0->v1:
- Add more details in the commit message and source comments.
- Update to the latest initialization sequences.
- Add access_ereg_modify_changed().
- Fix access_ereg() to access SMI bank correctly.
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch is to enable Intel SERDES power up/down sequence. The SERDES
converts 8/10 bits data to SGMII signal. Below is an example of
HW configuration for SGMII mode. The SERDES is located in the PHY IF
in the diagram below.
<-----------------GBE Controller---------->|<--External PHY chip-->
+----------+ +----+ +---+ +----------+
| EQoS | <-GMII->| DW | < ------ > |PHY| <-SGMII-> | External |
| MAC | |xPCS| |IF | | PHY |
+----------+ +----+ +---+ +----------+
^ ^ ^ ^
| | | |
+---------------------MDIO-------------------------+
PHY IF configuration and status registers are accessible through
mdio address 0x15 which is defined as mdio_adhoc_addr. During D0,
The driver will need to power up PHY IF by changing the power state
to P0. Likewise, for D3, the driver sets PHY IF power state to P3.
Signed-off-by: Voon Weifeng <weifeng.voon@intel.com>
Signed-off-by: Ong Boon Leong <boon.leong.ong@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Use the function devm_platform_ioremap_resource_byname() to simplify
source code which calls the functions platform_get_resource_byname()
and devm_ioremap_resource(). Remove also a few error messages which
became unnecessary with this software refactoring.
Suggested-by: Markus Elfring <Markus.Elfring@web.de>
Signed-off-by: Dejin Zheng <zhengdejin5@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
In the macvlan_device_event(), the list_first_entry_or_null() is used.
This function could return null pointer if there is no node.
But, the macvlan module doesn't check the null pointer.
So, null-ptr-deref would occur.
bond0
|
+----+-----+
| |
macvlan0 macvlan1
| |
dummy0 dummy1
The problem scenario.
If dummy1 is removed,
1. ->dellink() of dummy1 is called.
2. NETDEV_UNREGISTER of dummy1 notification is sent to macvlan module.
3. ->dellink() of macvlan1 is called.
4. NETDEV_UNREGISTER of macvlan1 notification is sent to bond module.
5. __bond_release_one() is called and it internally calls
dev_set_mac_address().
6. dev_set_mac_address() calls the ->ndo_set_mac_address() of macvlan1,
which is macvlan_set_mac_address().
7. macvlan_set_mac_address() calls the dev_set_mac_address() with dummy1.
8. NETDEV_CHANGEADDR of dummy1 is sent to macvlan module.
9. In the macvlan_device_event(), it calls list_first_entry_or_null().
At this point, dummy1 and macvlan1 were removed.
So, list_first_entry_or_null() will return NULL.
Test commands:
ip netns add nst
ip netns exec nst ip link add bond0 type bond
for i in {0..10}
do
ip netns exec nst ip link add dummy$i type dummy
ip netns exec nst ip link add macvlan$i link dummy$i \
type macvlan mode passthru
ip netns exec nst ip link set macvlan$i master bond0
done
ip netns del nst
Splat looks like:
[ 40.585687][ T146] general protection fault, probably for non-canonical address 0xdffffc0000000000: 0000 [#1] SMP DEI
[ 40.587249][ T146] KASAN: null-ptr-deref in range [0x0000000000000000-0x0000000000000007]
[ 40.588342][ T146] CPU: 1 PID: 146 Comm: kworker/u8:2 Not tainted 5.7.0-rc1+ #532
[ 40.589299][ T146] Hardware name: innotek GmbH VirtualBox/VirtualBox, BIOS VirtualBox 12/01/2006
[ 40.590469][ T146] Workqueue: netns cleanup_net
[ 40.591045][ T146] RIP: 0010:macvlan_device_event+0x4e2/0x900 [macvlan]
[ 40.591905][ T146] Code: 00 00 00 00 00 fc ff df 80 3c 06 00 0f 85 45 02 00 00 48 89 da 48 b8 00 00 00 00 00 fc ff d2
[ 40.594126][ T146] RSP: 0018:ffff88806116f4a0 EFLAGS: 00010246
[ 40.594783][ T146] RAX: dffffc0000000000 RBX: 0000000000000000 RCX: 0000000000000000
[ 40.595653][ T146] RDX: 0000000000000000 RSI: ffff88806547ddd8 RDI: ffff8880540f1360
[ 40.596495][ T146] RBP: ffff88804011a808 R08: fffffbfff4fb8421 R09: fffffbfff4fb8421
[ 40.597377][ T146] R10: ffffffffa7dc2107 R11: 0000000000000000 R12: 0000000000000008
[ 40.598186][ T146] R13: ffff88804011a000 R14: ffff8880540f1000 R15: 1ffff1100c22de9a
[ 40.599012][ T146] FS: 0000000000000000(0000) GS:ffff888067800000(0000) knlGS:0000000000000000
[ 40.600004][ T146] CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033
[ 40.600665][ T146] CR2: 00005572d3a807b8 CR3: 000000005fcf4003 CR4: 00000000000606e0
[ 40.601485][ T146] DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000
[ 40.602461][ T146] DR3: 0000000000000000 DR6: 00000000fffe0ff0 DR7: 0000000000000400
[ 40.603443][ T146] Call Trace:
[ 40.603871][ T146] ? nf_tables_dump_setelem+0xa0/0xa0 [nf_tables]
[ 40.604587][ T146] ? macvlan_uninit+0x100/0x100 [macvlan]
[ 40.605212][ T146] ? __module_text_address+0x13/0x140
[ 40.605842][ T146] notifier_call_chain+0x90/0x160
[ 40.606477][ T146] dev_set_mac_address+0x28e/0x3f0
[ 40.607117][ T146] ? netdev_notify_peers+0xc0/0xc0
[ 40.607762][ T146] ? __module_text_address+0x13/0x140
[ 40.608440][ T146] ? notifier_call_chain+0x90/0x160
[ 40.609097][ T146] ? dev_set_mac_address+0x1f0/0x3f0
[ 40.609758][ T146] dev_set_mac_address+0x1f0/0x3f0
[ 40.610402][ T146] ? __local_bh_enable_ip+0xe9/0x1b0
[ 40.611071][ T146] ? bond_hw_addr_flush+0x77/0x100 [bonding]
[ 40.611823][ T146] ? netdev_notify_peers+0xc0/0xc0
[ 40.612461][ T146] ? bond_hw_addr_flush+0x77/0x100 [bonding]
[ 40.613213][ T146] ? bond_hw_addr_flush+0x77/0x100 [bonding]
[ 40.613963][ T146] ? __local_bh_enable_ip+0xe9/0x1b0
[ 40.614631][ T146] ? bond_time_in_interval.isra.31+0x90/0x90 [bonding]
[ 40.615484][ T146] ? __bond_release_one+0x9f0/0x12c0 [bonding]
[ 40.616230][ T146] __bond_release_one+0x9f0/0x12c0 [bonding]
[ 40.616949][ T146] ? bond_enslave+0x47c0/0x47c0 [bonding]
[ 40.617642][ T146] ? lock_downgrade+0x730/0x730
[ 40.618218][ T146] ? check_flags.part.42+0x450/0x450
[ 40.618850][ T146] ? __mutex_unlock_slowpath+0xd0/0x670
[ 40.619519][ T146] ? trace_hardirqs_on+0x30/0x180
[ 40.620117][ T146] ? wait_for_completion+0x250/0x250
[ 40.620754][ T146] bond_netdev_event+0x822/0x970 [bonding]
[ 40.621460][ T146] ? __module_text_address+0x13/0x140
[ 40.622097][ T146] notifier_call_chain+0x90/0x160
[ 40.622806][ T146] rollback_registered_many+0x660/0xcf0
[ 40.623522][ T146] ? netif_set_real_num_tx_queues+0x780/0x780
[ 40.624290][ T146] ? notifier_call_chain+0x90/0x160
[ 40.624957][ T146] ? netdev_upper_dev_unlink+0x114/0x180
[ 40.625686][ T146] ? __netdev_adjacent_dev_unlink_neighbour+0x30/0x30
[ 40.626421][ T146] ? mutex_is_locked+0x13/0x50
[ 40.627016][ T146] ? unregister_netdevice_queue+0xf2/0x240
[ 40.627663][ T146] unregister_netdevice_many.part.134+0x13/0x1b0
[ 40.628362][ T146] default_device_exit_batch+0x2d9/0x390
[ 40.628987][ T146] ? unregister_netdevice_many+0x40/0x40
[ 40.629615][ T146] ? dev_change_net_namespace+0xcb0/0xcb0
[ 40.630279][ T146] ? prepare_to_wait_exclusive+0x2e0/0x2e0
[ 40.630943][ T146] ? ops_exit_list.isra.9+0x97/0x140
[ 40.631554][ T146] cleanup_net+0x441/0x890
[ ... ]
Fixes: e289fd28176b ("macvlan: fix the problem when mac address changes for passthru mode")
Reported-by: syzbot+5035b1f9dc7ea4558d5a@syzkaller.appspotmail.com
Signed-off-by: Taehee Yoo <ap420073@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The '==' expression itself is bool, no need to convert it to bool again.
This fixes the following coccicheck warning:
drivers/net/ethernet/intel/e1000/e1000_main.c:1479:44-49: WARNING:
conversion to bool not needed here
Signed-off-by: Jason Yan <yanaijie@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The '==' expression itself is bool, no need to convert it to bool again.
This fixes the following coccicheck warning:
drivers/net/ethernet/intel/i40e/i40e_main.c:1614:52-57: WARNING:
conversion to bool not needed here
drivers/net/ethernet/intel/i40e/i40e_main.c:11439:52-57: WARNING:
conversion to bool not needed here
Signed-off-by: Jason Yan <yanaijie@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Pull virtio fixes and cleanups from Michael Tsirkin:
- Some bug fixes
- Cleanup a couple of issues that surfaced meanwhile
- Disable vhost on ARM with OABI for now - to be fixed fully later in
the cycle or in the next release.
* tag 'for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mst/vhost: (24 commits)
vhost: disable for OABI
virtio: drop vringh.h dependency
virtio_blk: add a missing include
virtio-balloon: Avoid using the word 'report' when referring to free page hinting
virtio-balloon: make virtballoon_free_page_report() static
vdpa: fix comment of vdpa_register_device()
vdpa: make vhost, virtio depend on menu
vdpa: allow a 32 bit vq alignment
drm/virtio: fix up for include file changes
remoteproc: pull in slab.h
rpmsg: pull in slab.h
virtio_input: pull in slab.h
remoteproc: pull in slab.h
virtio-rng: pull in slab.h
virtgpu: pull in uaccess.h
tools/virtio: make asm/barrier.h self contained
tools/virtio: define aligned attribute
virtio/test: fix up after IOTLB changes
vhost: Create accessors for virtqueues private_data
vdpasim: Return status in vdpasim_get_status
...
|
|
In the reference BIOS implementation, WRDS can be disabled without
disabling WGDS. And this happens in most cases where WRDS is
disabled, causing the WGDS without WRDS check and issue an error.
To avoid this issue, we change the check so that we only considered it
an error if the WRDS entry doesn't exist. If the entry (or the
selected profile is disabled for any other reason), we just silently
ignore WGDS.
Cc: stable@vger.kernel.org # 4.14+
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=205513
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/iwlwifi.20200417133700.72ad25c3998b.I875d935cefd595ed7f640ddcfc7bc802627d2b7f@changeid
|
|
The function iwl_mvm_remove_inactive_tids() returns bool, so we
should just check "if (ret)", not "if (ret >= 0)" (which would
do nothing useful here). We obviously therefore cannot use the
return value of the function for the free_queue, we need to use
the queue (i) we're currently dealing with instead.
Cc: stable@vger.kernel.org # v5.4+
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/iwlwifi.20200417100405.9d862ed72535.I9e27ccc3ee3c8855fc13682592b571581925dfbd@changeid
|
|
As this was not supposed to be enabled to begin with.
Cc: stable@vger.kernel.org # v4.19+
Signed-off-by: Ilan Peer <ilan.peer@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/iwlwifi.20200417100405.53dbc3c6c36b.Idfe118546b92cc31548b2211472a5303c7de5909@changeid
|
|
Due to some hardware issues, queue 31 isn't usable on devices that have
32 queues (7000, 8000, 9000 families), which is correctly reflected in
the configuration and TX queue initialization.
However, the firmware API and queue allocation code assumes that there
are 32 queues, and if something actually attempts to use #31 this leads
to a NULL-pointer dereference since it's not allocated.
Fix this by limiting to 31 in the IWL_MVM_DQA_MAX_DATA_QUEUE, and also
add some code to catch this earlier in the future, if the configuration
changes perhaps.
Cc: stable@vger.kernel.org # v4.9+
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/iwlwifi.20200417100405.98a79be2db6a.I3a4af6b03b87a6bc18db9b1ff9a812f397bee1fc@changeid
|
|
In the context info, we need to indicate the correct RB size
to the device so that it will not think we have 4k when we
only use 2k. This seems to not have caused any issues right
now, likely because the hardware no longer supports putting
multiple entries into a single RB, and practically all of
the entries should be smaller than 2k.
Nevertheless, it's a bug, and we must advertise the right
size to the device.
Note that right now we can only tell it 2k vs. 4k, so for
the cases where we have more, still use 4k. This needs to
be fixed by the firmware first.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Fixes: cfdc20efebdc ("iwlwifi: pcie: use partial pages if applicable")
Cc: stable@vger.kernel.org # v5.6
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/iwlwifi.20200417100405.ae6cd345764f.I0985c55223decf70182b9ef1d8edf4179f537853@changeid
|
|
We reset statistics also in case that we didn't reassoc so in
this cases keep last beacon counter.
Cc: stable@vger.kernel.org # v4.19+
Signed-off-by: Mordechay Goodstein <mordechay.goodstein@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/iwlwifi.20200417100405.1f9142751fbc.Ifbfd0f928a0a761110b8f4f2ca5483a61fb21131@changeid
|
|
The iwl_trans_pcie_dyn_txq_free() function only releases the frames
that may be left on the queue by calling iwl_pcie_gen2_txq_unmap(),
but doesn't actually free the DMA ring or byte-count tables for the
queue. This leads to pretty large memory leaks (at least before my
queue size improvements), in particular in monitor/sniffer mode on
channel hopping since this happens on every channel change.
This was also now more evident after the move to a DMA pool for the
byte count tables, showing messages such as
BUG iwlwifi:bc (...): Objects remaining in iwlwifi:bc on __kmem_cache_shutdown()
This fixes https://bugzilla.kernel.org/show_bug.cgi?id=206811.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Fixes: 6b35ff91572f ("iwlwifi: pcie: introduce a000 TX queues management")
Cc: stable@vger.kernel.org # v4.14+
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/iwlwifi.20200417100405.f5f4c4193ec1.Id5feebc9b4318041913a9c89fc1378bb5454292c@changeid
|
|
Commit 71bc0334a637 ("iwlwifi: check allocated pointer when allocating
conf_tlvs") attempted to fix a typoe introduced by commit 17b809c9b22e
("iwlwifi: dbg: move debug data to a struct") but does not implement the
check correctly.
Fixes: 71bc0334a637 ("iwlwifi: check allocated pointer when allocating conf_tlvs")
Tweeted-by: @grsecurity
Signed-off-by: Chris Rorvick <chris@rorvick.com>
Signed-off-by: Sedat Dilek <sedat.dilek@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200417074558.12316-1-sedat.dilek@gmail.com
|
|
In the switchdev mode, when running "cat
/sys/class/net/NIC/statistics/tx_packets", the ppcnt register is
accessed to get the latest values. But currently this command can
not get the correct values from ppcnt.
From firmware manual, before getting the 802_3 counters, the 802_3
data layout should be set to the ppcnt register.
When the command "cat /sys/class/net/NIC/statistics/tx_packets" is
run, before updating 802_3 data layout with ppcnt register, the
monitor counters are tested. The test result will decide the
802_3 data layout is updated or not.
Actually the monitor counters do not support to monitor rx/tx
stats of 802_3 in switchdev mode. So the rx/tx counters change
will not trigger monitor counters. So the 802_3 data layout will
not be updated in ppcnt register. Finally this command can not get
the latest values from ppcnt register with 802_3 data layout.
Fixes: 5c7e8bbb0257 ("net/mlx5e: Use monitor counters for update stats")
Signed-off-by: Zhu Yanjun <yanjunz@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
|
|
MLX5_CORE uses the 'imply' keyword to depend on VXLAN, PTP_1588_CLOCK,
MLXFW and PCI_HYPERV_INTERFACE.
This was useful to force vxlan, ptp, etc.. to be reachable to mlx5
regardless of their config states.
Due to the changes in the cited commit below, the semantics of 'imply'
was changed to not force any restriction on the implied config.
As a result of this change, the compilation of MLX5_CORE=y and VXLAN=m
would result in undefined references, as VXLAN now would stay as 'm'.
To fix this we change MLX5_CORE to have a weak dependency on
these modules/configs and make sure they are reachable, by adding:
depend on symbol || !symbol.
For example: VXLAN=m MLX5_CORE=y, this will force MLX5_CORE to m
Fixes: def2fbffe62c ("kconfig: allow symbols implied by y to become m")
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Cc: Masahiro Yamada <masahiroy@kernel.org>
Cc: Nicolas Pitre <nico@fluxnic.net>
Cc: Arnd Bergmann <arnd@arndb.de>
Reported-by: Randy Dunlap <rdunlap@infradead.org>
|
|
XSK wakeup function triggers NAPI by posting a NOP WQE to a special XSK
ICOSQ. When the application floods the driver with wakeup requests by
calling sendto() in a certain pattern that ends up in mlx5e_trigger_irq,
the XSK ICOSQ may overflow.
Multiple NOPs are not required and won't accelerate the process, so
avoid posting a second NOP if there is one already on the way. This way
we also avoid increasing the queue size (which might not help anyway).
Fixes: db05815b36cb ("net/mlx5e: Add XSK zero-copy support")
Signed-off-by: Maxim Mikityanskiy <maximmi@mellanox.com>
Reviewed-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
|
|
After allowing parallel tuple insertion, we get the following trace:
[ 5505.142249] ------------[ cut here ]------------
[ 5505.148155] WARNING: CPU: 21 PID: 13313 at lib/radix-tree.c:581 delete_node+0x16c/0x180
[ 5505.295553] CPU: 21 PID: 13313 Comm: kworker/u50:22 Tainted: G OE 5.6.0+ #78
[ 5505.304824] Hardware name: Supermicro Super Server/X10DRT-P, BIOS 2.0b 03/30/2017
[ 5505.313740] Workqueue: nf_flow_table_offload flow_offload_work_handler [nf_flow_table]
[ 5505.323257] RIP: 0010:delete_node+0x16c/0x180
[ 5505.349862] RSP: 0018:ffffb19184eb7b30 EFLAGS: 00010282
[ 5505.356785] RAX: 0000000000000000 RBX: ffff904ac95b86d8 RCX: ffff904b6f938838
[ 5505.365190] RDX: 0000000000000000 RSI: ffff904ac954b908 RDI: ffff904ac954b920
[ 5505.373628] RBP: ffff904b4ac13060 R08: 0000000000000001 R09: 0000000000000000
[ 5505.382155] R10: 0000000000000000 R11: 0000000000000040 R12: 0000000000000000
[ 5505.390527] R13: ffffb19184eb7bfc R14: ffff904b6bef5800 R15: ffff90482c1203c0
[ 5505.399246] FS: 0000000000000000(0000) GS:ffff904c2fc80000(0000) knlGS:0000000000000000
[ 5505.408621] CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033
[ 5505.415739] CR2: 00007f5d27006010 CR3: 0000000058c10006 CR4: 00000000001626e0
[ 5505.424547] Call Trace:
[ 5505.428429] idr_alloc_u32+0x7b/0xc0
[ 5505.433803] mlx5_tc_ct_entry_add_rule+0xbf/0x950 [mlx5_core]
[ 5505.441354] ? mlx5_fc_create+0x23c/0x370 [mlx5_core]
[ 5505.448225] mlx5_tc_ct_block_flow_offload+0x874/0x10b0 [mlx5_core]
[ 5505.456278] ? mlx5_tc_ct_block_flow_offload+0x63d/0x10b0 [mlx5_core]
[ 5505.464532] nf_flow_offload_tuple.isra.21+0xc5/0x140 [nf_flow_table]
[ 5505.472286] ? __kmalloc+0x217/0x2f0
[ 5505.477093] ? flow_rule_alloc+0x1c/0x30
[ 5505.482117] flow_offload_work_handler+0x1d0/0x290 [nf_flow_table]
[ 5505.489674] ? process_one_work+0x17c/0x580
[ 5505.494922] process_one_work+0x202/0x580
[ 5505.500082] ? process_one_work+0x17c/0x580
[ 5505.505696] worker_thread+0x4c/0x3f0
[ 5505.510458] kthread+0x103/0x140
[ 5505.514989] ? process_one_work+0x580/0x580
[ 5505.520616] ? kthread_bind+0x10/0x10
[ 5505.525837] ret_from_fork+0x3a/0x50
[ 5505.570841] ---[ end trace 07995de9c56d6831 ]---
This happens from parallel deletes/adds to idr, as idr isn't protected.
Fix that by using xarray as the tuple_ids allocator instead of idr.
Fixes: 7da182a998d6 ("netfilter: flowtable: Use work entry per offload command")
Reviewed-by: Roi Dayan <roid@mellanox.com>
Signed-off-by: Paul Blakey <paulb@mellanox.com>
Reviewed-by: Oz Shlomo <ozsh@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
|
|
On s390 FORCE_MAX_ZONEORDER is 9 instead of 11, thus a larger kzalloc()
allocation as done for the firmware tracer will always fail.
Looking at mlx5_fw_tracer_save_trace(), it is actually the driver itself
that copies the debug data into the trace array and there is no need for
the allocation to be contiguous in physical memory. We can therefor use
kvzalloc() instead of kzalloc() and get rid of the large contiguous
allcoation.
Fixes: f53aaa31cce7 ("net/mlx5: FW tracer, implement tracer logic")
Signed-off-by: Niklas Schnelle <schnelle@linux.ibm.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
|
|
When team mode is changed or set, the team_mode_get() is called to check
whether the mode module is inserted or not. If the mode module is not
inserted, it calls the request_module().
In the request_module(), it creates a child process, which is
the "modprobe" process and waits for the done of the child process.
At this point, the following locks were used.
down_read(&cb_lock()); by genl_rcv()
genl_lock(); by genl_rcv_msc()
rtnl_lock(); by team_nl_cmd_options_set()
mutex_lock(&team->lock); by team_nl_team_get()
Concurrently, the team module could be removed by rmmod or "modprobe -r"
The __exit function of team module is team_module_exit(), which calls
team_nl_fini() and it tries to acquire following locks.
down_write(&cb_lock);
genl_lock();
Because of the genl_lock() and cb_lock, this process can't be finished
earlier than request_module() routine.
The problem secenario.
CPU0 CPU1
team_mode_get
request_module()
modprobe -r team_mode_roundrobin
team <--(B)
modprobe team <--(A)
team_mode_roundrobin
By request_module(), the "modprobe team_mode_roundrobin" command
will be executed. At this point, the modprobe process will decide
that the team module should be inserted before team_mode_roundrobin.
Because the team module is being removed.
By the module infrastructure, the same module insert/remove operations
can't be executed concurrently.
So, (A) waits for (B) but (B) also waits for (A) because of locks.
So that the hang occurs at this point.
Test commands:
while :
do
teamd -d &
killall teamd &
modprobe -rv team_mode_roundrobin &
done
The approach of this patch is to hold the reference count of the team
module if the team module is compiled as a module. If the reference count
of the team module is not zero while request_module() is being called,
the team module will not be removed at that moment.
So that the above scenario could not occur.
Fixes: 3d249d4ca7d0 ("net: introduce ethernet teaming device")
Signed-off-by: Taehee Yoo <ap420073@gmail.com>
Reviewed-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Fetching PTP sync information from mailbox is slow and can take
up to 10 milliseconds. Reduce this unnecessary delay by directly
reading the information from the corresponding registers.
Fixes: 9c33e4208bce ("cxgb4: Add PTP Hardware Clock (PHC) support")
Signed-off-by: Manoj Malviya <manojmalviya@chelsio.com>
Signed-off-by: Rahul Lakkireddy <rahul.lakkireddy@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Running with KASAN on a VIM3L systems leads to the following splat
when probing the Ethernet device:
==================================================================
BUG: KASAN: global-out-of-bounds in _get_maxdiv+0x74/0xd8
Read of size 4 at addr ffffa000090615f4 by task systemd-udevd/139
CPU: 1 PID: 139 Comm: systemd-udevd Tainted: G E 5.7.0-rc1-00101-g8624b7577b9c #781
Hardware name: amlogic w400/w400, BIOS 2020.01-rc5 03/12/2020
Call trace:
dump_backtrace+0x0/0x2a0
show_stack+0x20/0x30
dump_stack+0xec/0x148
print_address_description.isra.12+0x70/0x35c
__kasan_report+0xfc/0x1d4
kasan_report+0x4c/0x68
__asan_load4+0x9c/0xd8
_get_maxdiv+0x74/0xd8
clk_divider_bestdiv+0x74/0x5e0
clk_divider_round_rate+0x80/0x1a8
clk_core_determine_round_nolock.part.9+0x9c/0xd0
clk_core_round_rate_nolock+0xf0/0x108
clk_hw_round_rate+0xac/0xf0
clk_factor_round_rate+0xb8/0xd0
clk_core_determine_round_nolock.part.9+0x9c/0xd0
clk_core_round_rate_nolock+0xf0/0x108
clk_core_round_rate_nolock+0xbc/0x108
clk_core_set_rate_nolock+0xc4/0x2e8
clk_set_rate+0x58/0xe0
meson8b_dwmac_probe+0x588/0x72c [dwmac_meson8b]
platform_drv_probe+0x78/0xd8
really_probe+0x158/0x610
driver_probe_device+0x140/0x1b0
device_driver_attach+0xa4/0xb0
__driver_attach+0xcc/0x1c8
bus_for_each_dev+0xf4/0x168
driver_attach+0x3c/0x50
bus_add_driver+0x238/0x2e8
driver_register+0xc8/0x1e8
__platform_driver_register+0x88/0x98
meson8b_dwmac_driver_init+0x28/0x1000 [dwmac_meson8b]
do_one_initcall+0xa8/0x328
do_init_module+0xe8/0x368
load_module+0x3300/0x36b0
__do_sys_finit_module+0x120/0x1a8
__arm64_sys_finit_module+0x4c/0x60
el0_svc_common.constprop.2+0xe4/0x268
do_el0_svc+0x98/0xa8
el0_svc+0x24/0x68
el0_sync_handler+0x12c/0x318
el0_sync+0x158/0x180
The buggy address belongs to the variable:
div_table.63646+0x34/0xfffffffffffffa40 [dwmac_meson8b]
Memory state around the buggy address:
ffffa00009061480: fa fa fa fa 00 00 00 01 fa fa fa fa 00 00 00 00
ffffa00009061500: 05 fa fa fa fa fa fa fa 00 04 fa fa fa fa fa fa
>ffffa00009061580: 00 03 fa fa fa fa fa fa 00 00 00 00 00 00 fa fa
^
ffffa00009061600: fa fa fa fa 00 01 fa fa fa fa fa fa 01 fa fa fa
ffffa00009061680: fa fa fa fa 00 01 fa fa fa fa fa fa 04 fa fa fa
==================================================================
Digging into this indeed shows that the clock divider array is
lacking a final fence, and that the clock subsystems goes in the
weeds. Oh well.
Let's add the empty structure that indicates the end of the array.
Fixes: bd6f48546b9c ("net: stmmac: dwmac-meson8b: Fix the RGMII TX delay on Meson8b/8m2 SoCs")
Signed-off-by: Marc Zyngier <maz@kernel.org>
Cc: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Reviewed-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
In the function bcm_sysport_probe(), when get irq failed, the function
platform_get_irq() logs an error message, so remove redundant message
here.
Signed-off-by: Tang Bin <tangbin@cmss.chinamobile.com>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
vhost is currently broken on the some ARM configs.
The reason is that the ring element addresses are passed between
components with different alignments assumptions. Thus, if
guest selects a pointer and host then gets and dereferences
it, then alignment assumed by the host's compiler might be
greater than the actual alignment of the pointer.
compiler on the host from assuming pointer is aligned.
This actually triggers on ARM with -mabi=apcs-gnu - which is a
deprecated configuration. With this OABI, compiler assumes that
all structures are 4 byte aligned - which is stronger than
virtio guarantees for available and used rings, which are
merely 2 bytes. Thus a guest without -mabi=apcs-gnu running
on top of host with -mabi=apcs-gnu will be broken.
The correct fix is to force alignment of structures - however
that is an intrusive fix that's best deferred until the next release.
We didn't previously support such ancient systems at all - this surfaced
after vdpa support prompted removing dependency of vhost on
VIRTULIZATION. So for now, let's just add something along the lines of
depends on !ARM || AEABI
to the virtio Kconfig declaration, and add a comment that it has to do
with struct member alignment.
Note: we can't make VHOST and VHOST_RING themselves have
a dependency since these are selected. Add a new symbol for that.
We should be able to drop this dependency down the road.
Fixes: 20c384f1ea1a0bc7 ("vhost: refine vhost and vringh kconfig")
Suggested-by: Ard Biesheuvel <ardb@kernel.org>
Suggested-by: Richard Earnshaw <Richard.Earnshaw@arm.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
|
|
Commit 9ecc2d86171a ("net/mlx4_en: add xdp forwarding and data write support")
brought another indirect call in fast path.
Use INDIRECT_CALL_2() helper to avoid the cost of the indirect call
when/if CONFIG_RETPOLINE=y
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Tariq Toukan <tariqt@mellanox.com>
Cc: Willem de Bruijn <willemb@google.com>
Reviewed-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
In fine adjustement mode, which is the current default, the sub-second
increment register is the number of nanoseconds that will be added to
the clock when the accumulator overflows. At each clock cycle, the
value of the addend register is added to the accumulator.
Currently, we use 20ns = 1e09ns / 50MHz as this value whatever the
frequency of the ptp clock actually is.
The adjustment is then done on the addend register, only incrementing
every X clock cycles X being the ratio between 50MHz and ptp_clock_rate
(addend = 2^32 * 50MHz/ptp_clock_rate).
This causes the following issues :
- In case the frequency of the ptp clock is inferior or equal to 50MHz,
the addend value calculation will overflow and the default
addend value will be set to 0, causing the clock to not work at
all. (For instance, for ptp_clock_rate = 50MHz, addend = 2^32).
- The resolution of the timestamping clock is limited to 20ns while it
is not needed, thus limiting the accuracy of the timestamping to
20ns.
Fix this by setting sub-second increment to 2e09ns / ptp_clock_rate.
It will allow to reach the minimum possible frequency for
ptp_clk_ref, which is 5MHz for GMII 1000Mps Full-Duplex by setting the
sub-second-increment to a higher value. For instance, for 25MHz, it
gives ssinc = 80ns and default_addend = 2^31.
It will also allow to use a lower value for sub-second-increment, thus
improving the timestamping accuracy with frequencies higher than
100MHz, for instance, for 200MHz, ssinc = 10ns and default_addend =
2^31.
v1->v2:
- Remove modifications to the calculation of default addend, which broke
compatibility with clock frequencies for which 2000000000 / ptp_clk_freq
is not an integer.
- Modify description according to discussions.
Signed-off-by: Julien Beraud <julien.beraud@orolia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
There are 2 registers to write to enable a ptp ref clock coming from the
fpga.
One that enables the usage of the clock from the fpga for emac0 and emac1
as a ptp ref clock, and the other to allow signals from the fpga to reach
emac0 and emac1.
Currently, if the dwmac-socfpga has phymode set to PHY_INTERFACE_MODE_MII,
PHY_INTERFACE_MODE_GMII, or PHY_INTERFACE_MODE_SGMII, both registers will
be written and the ptp ref clock will be set as coming from the fpga.
Separate the 2 register writes to only enable signals from the fpga to
reach emac0 or emac1 when ptp ref clock is not coming from the fpga.
Signed-off-by: Julien Beraud <julien.beraud@orolia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
i2400mu_bus_bm_wait_for_ack() invokes usb_get_urb(), which increases the
refcount of the "notif_urb".
When i2400mu_bus_bm_wait_for_ack() returns, local variable "notif_urb"
becomes invalid, so the refcount should be decreased to keep refcount
balanced.
The issue happens in all paths of i2400mu_bus_bm_wait_for_ack(), which
forget to decrease the refcnt increased by usb_get_urb(), causing a
refcnt leak.
Fix this issue by calling usb_put_urb() before the
i2400mu_bus_bm_wait_for_ack() returns.
Signed-off-by: Xiyu Yang <xiyuyang19@fudan.edu.cn>
Signed-off-by: Xin Tan <tanxin.ctf@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Pull networking fixes from David Miller:
1) Disable RISCV BPF JIT builds when !MMU, from Björn Töpel.
2) nf_tables leaves dangling pointer after free, fix from Eric Dumazet.
3) Out of boundary write in __xsk_rcv_memcpy(), fix from Li RongQing.
4) Adjust icmp6 message source address selection when routes have a
preferred source address set, from Tim Stallard.
5) Be sure to validate HSR protocol version when creating new links,
from Taehee Yoo.
6) CAP_NET_ADMIN should be sufficient to manage l2tp tunnels even in
non-initial namespaces, from Michael Weiß.
7) Missing release firmware call in mlx5, from Eran Ben Elisha.
8) Fix variable type in macsec_changelink(), caught by KASAN. Fix from
Taehee Yoo.
9) Fix pause frame negotiation in marvell phy driver, from Clemens
Gruber.
10) Record RX queue early enough in tun packet paths such that XDP
programs will see the correct RX queue index, from Gilberto Bertin.
11) Fix double unlock in mptcp, from Florian Westphal.
12) Fix offset overflow in ARM bpf JIT, from Luke Nelson.
13) marvell10g needs to soft reset PHY when coming out of low power
mode, from Russell King.
14) Fix MTU setting regression in stmmac for some chip types, from
Florian Fainelli.
* git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net: (101 commits)
amd-xgbe: Use __napi_schedule() in BH context
mISDN: make dmril and dmrim static
net: stmmac: dwmac-sunxi: Provide TX and RX fifo sizes
net: dsa: mt7530: fix tagged frames pass-through in VLAN-unaware mode
tipc: fix incorrect increasing of link window
Documentation: Fix tcp_challenge_ack_limit default value
net: tulip: make early_486_chipsets static
dt-bindings: net: ethernet-phy: add desciption for ethernet-phy-id1234.d400
ipv6: remove redundant assignment to variable err
net/rds: Use ERR_PTR for rds_message_alloc_sgs()
net: mscc: ocelot: fix untagged packet drops when enslaving to vlan aware bridge
selftests/bpf: Check for correct program attach/detach in xdp_attach test
libbpf: Fix type of old_fd in bpf_xdp_set_link_opts
libbpf: Always specify expected_attach_type on program load if supported
xsk: Add missing check on user supplied headroom size
mac80211: fix channel switch trigger from unknown mesh peer
mac80211: fix race in ieee80211_register_hw()
net: marvell10g: soft-reset the PHY when coming out of low power
net: marvell10g: report firmware version
net/cxgb4: Check the return from t4_query_params properly
...
|
|
The driver uses __napi_schedule_irqoff() which is fine as long as it is
invoked with disabled interrupts by everybody. Since the commit
mentioned below the driver may invoke xgbe_isr_task() in tasklet/softirq
context. This may lead to list corruption if another driver uses
__napi_schedule_irqoff() in IRQ context.
Use __napi_schedule() which safe to use from IRQ and softirq context.
Fixes: 85b85c853401d ("amd-xgbe: Re-issue interrupt if interrupt status not cleared")
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Acked-by: Tom Lendacky <thomas.lendacky@amd.com>
Cc: Tom Lendacky <thomas.lendacky@amd.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
After commit bfcb813203e619a8960a819bf533ad2a108d8105 ("net: dsa:
configure the MTU for switch ports") my Lamobo R1 platform which uses
an allwinner,sun7i-a20-gmac compatible Ethernet MAC started to fail
by rejecting a MTU of 1536. The reason for that is that the DMA
capabilities are not readable on this version of the IP, and there
is also no 'tx-fifo-depth' property being provided in Device Tree. The
property is documented as optional, and is not provided.
Chen-Yu indicated that the FIFO sizes are 4KB for TX and 16KB for RX, so
provide these values through platform data as an immediate fix until
various Device Tree sources get updated accordingly.
Fixes: eaf4fac47807 ("net: stmmac: Do not accept invalid MTU values")
Suggested-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Acked-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
In VLAN-unaware mode, the Egress Tag (EG_TAG) field in Port VLAN
Control register must be set to Consistent to let tagged frames pass
through as is, otherwise their tags will be stripped.
Fixes: 83163f7dca56 ("net: dsa: mediatek: add VLAN support for MT7530")
Signed-off-by: DENG Qingfang <dqfext@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Tested-by: René van Dorst <opensource@vdorst.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Fix the following sparse warning:
drivers/net/ethernet/dec/tulip/tulip_core.c:1280:28: warning: symbol
'early_486_chipsets' was not declared. Should it be static?
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Jason Yan <yanaijie@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
To rehash a previous explanation given in commit 1c44ce560b4d ("net:
mscc: ocelot: fix vlan_filtering when enslaving to bridge before link is
up"), the switch driver operates the in a mode where a single VLAN can
be transmitted as untagged on a particular egress port. That is the
"native VLAN on trunk port" use case.
The configuration for this native VLAN is driven in 2 ways:
- Set the egress port rewriter to strip the VLAN tag for the native
VID (as it is egress-untagged, after all).
- Configure the ingress port to drop untagged and priority-tagged
traffic, if there is no native VLAN. The intention of this setting is
that a trunk port with no native VLAN should not accept untagged
traffic.
Since both of the above configurations for the native VLAN should only
be done if VLAN awareness is requested, they are actually done from the
ocelot_port_vlan_filtering function, after the basic procedure of
toggling the VLAN awareness flag of the port.
But there's a problem with that simplistic approach: we are trying to
juggle with 2 independent variables from a single function:
- Native VLAN of the port - its value is held in port->vid.
- VLAN awareness state of the port - currently there are some issues
here, more on that later*.
The actual problem can be seen when enslaving the switch ports to a VLAN
filtering bridge:
0. The driver configures a pvid of zero for each port, when in
standalone mode. While the bridge configures a default_pvid of 1 for
each port that gets added as a slave to it.
1. The bridge calls ocelot_port_vlan_filtering with vlan_aware=true.
The VLAN-filtering-dependent portion of the native VLAN
configuration is done, considering that the native VLAN is 0.
2. The bridge calls ocelot_vlan_add with vid=1, pvid=true,
untagged=true. The native VLAN changes to 1 (change which gets
propagated to hardware).
3. ??? - nobody calls ocelot_port_vlan_filtering again, to reapply the
VLAN-filtering-dependent portion of the native VLAN configuration,
for the new native VLAN of 1. One can notice that after toggling "ip
link set dev br0 type bridge vlan_filtering 0 && ip link set dev br0
type bridge vlan_filtering 1", the new native VLAN finally makes it
through and untagged traffic finally starts flowing again. But
obviously that shouldn't be needed.
So it is clear that 2 independent variables need to both re-trigger the
native VLAN configuration. So we introduce the second variable as
ocelot_port->vlan_aware.
*Actually both the DSA Felix driver and the Ocelot driver already had
each its own variable:
- Ocelot: ocelot_port_private->vlan_aware
- Felix: dsa_port->vlan_filtering
but the common Ocelot library needs to work with a single, common,
variable, so there is some refactoring done to move the vlan_aware
property from the private structure into the common ocelot_port
structure.
Fixes: 97bb69e1e36e ("net: mscc: ocelot: break apart ocelot_vlan_port_apply")
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Horatiu Vultur <horatiu.vultur@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/jberg/mac80211
Johannes Berg says:
====================
A couple of fixes:
* FTM responder policy netlink validation fix
(but the only user validates again later)
* kernel-doc fixes
* a fix for a race in mac80211 radio registration vs. userspace
* a mesh channel switch fix
* a fix for a syzbot reported kasprintf() issue
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Soft-reset the PHY when coming out of low power mode, which seems to
be necessary with firmware versions 0.3.3.0 and 0.3.10.0.
This depends on ("net: marvell10g: report firmware version")
Fixes: c9cc1c815d36 ("net: phy: marvell10g: place in powersave mode at probe")
Reported-by: Matteo Croce <mcroce@redhat.com>
Tested-by: Matteo Croce <mcroce@redhat.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Report the firmware version when probing the PHY to allow issues
attributable to firmware to be diagnosed.
Tested-by: Matteo Croce <mcroce@redhat.com>
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Positive return values are also failures that don't set val,
although this probably can't happen. Fixes gcc 10 warning:
drivers/net/ethernet/chelsio/cxgb4/t4_hw.c: In function ‘t4_phy_fw_ver’:
drivers/net/ethernet/chelsio/cxgb4/t4_hw.c:3747:14: warning: ‘val’ may be used uninitialized in this function [-Wmaybe-uninitialized]
3747 | *phy_fw_ver = val;
Fixes: 01b6961410b7 ("cxgb4: Add PHY firmware support for T420-BT cards")
Signed-off-by: Jason Gunthorpe <jgg@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Allow all the RGMII modes to be used. (Not only "rgmii", "rgmii-id"
but "rgmii-txid", "rgmii-rxid")
Signed-off-by: Atsushi Nemoto <atsushi.nemoto@sord.co.jp>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The 88e6185 is reporting it has detected a PHY, when a port is
connected to an SFP. As a result, the fixed-phy configuration is not
being applied. That then breaks packet transfer, since the port is
reported as being down.
Add additional conditions to check the interface mode, and if it is
fixed always configure the port on link up/down, independent of the
PPU status.
Fixes: 30c4a5b0aad8 ("net: mv88e6xxx: use resolved link config in mac_link_up()")
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Remove an unused initialized value.
Fixes: 7e4d47596b68 ("ionic: replay filters after fw upgrade")
Reported-by: kbuild test robot <lkp@intel.com>
Signed-off-by: Shannon Nelson <snelson@pensando.io>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add the appropriate header for using dynamic_hex_dump(), which
seems to be incidentally included in some configurations but
not all.
Fixes: 7e4d47596b68 ("ionic: replay filters after fw upgrade")
Reported-by: Randy Dunlap <rdunlap@infradead.org>
Signed-off-by: Shannon Nelson <snelson@pensando.io>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
KSZ9131 will not work with some switches due to workaround for KSZ9031
introduced in commit d2fd719bcb0e83cb39cfee22ee800f98a56eceb3
("net/phy: micrel: Add workaround for bad autoneg").
Use genphy_read_status instead of dedicated ksz9031_read_status.
Fixes: bff5b4b37372 ("net: phy: micrel: add Microchip KSZ9131 initial driver")
Signed-off-by: Atsushi Nemoto <atsushi.nemoto@sord.co.jp>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/kvalo/wireless-drivers
Kalle Valo says:
====================
wireless-drivers fixes for v5.7
First set of fixes for v5.6. Fixes for a crash and for two compiler
warnings.
brcmfmac
* fix a crash related to monitor interface
ath11k
* fix compiler warnings without CONFIG_THERMAL
rtw88
* fix compiler warnings related to suspend and resume functions
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The rtw88 driver defines emtpy functions with multiple indirections
but gets one of these wrong:
drivers/net/wireless/realtek/rtw88/pci.c:1347:12: error: 'rtw_pci_resume' defined but not used [-Werror=unused-function]
1347 | static int rtw_pci_resume(struct device *dev)
| ^~~~~~~~~~~~~~
drivers/net/wireless/realtek/rtw88/pci.c:1342:12: error: 'rtw_pci_suspend' defined but not used [-Werror=unused-function]
1342 | static int rtw_pci_suspend(struct device *dev)
Better simplify it to rely on the conditional reference in
SIMPLE_DEV_PM_OPS(), and mark the functions as __maybe_unused to avoid
warning about it.
I'm not sure if these are needed at all given that the functions
don't do anything, but they were only recently added.
Fixes: 44bc17f7f5b3 ("rtw88: support wowlan feature for 8822c")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200408185413.218643-1-arnd@arndb.de
|
|
syzbot reports a warning:
precision 33020 too large
WARNING: CPU: 0 PID: 9618 at lib/vsprintf.c:2471 set_precision+0x150/0x180 lib/vsprintf.c:2471
vsnprintf+0xa7b/0x19a0 lib/vsprintf.c:2547
kvasprintf+0xb2/0x170 lib/kasprintf.c:22
kasprintf+0xbb/0xf0 lib/kasprintf.c:59
hwsim_del_radio_nl+0x63a/0x7e0 drivers/net/wireless/mac80211_hwsim.c:3625
genl_family_rcv_msg_doit net/netlink/genetlink.c:672 [inline]
...
entry_SYSCALL_64_after_hwframe+0x49/0xbe
Thus it seems that kasprintf() with "%.*s" format can not be used for
duplicating a string with arbitrary length. Replace it with kstrndup().
Note that later this string is limited to NL80211_WIPHY_NAME_MAXLEN == 64,
but the code is simpler this way.
Reported-by: syzbot+6693adf1698864d21734@syzkaller.appspotmail.com
Reported-by: syzbot+a4aee3f42d7584d76761@syzkaller.appspotmail.com
Cc: stable@kernel.org
Signed-off-by: Tuomas Tynkkynen <tuomas.tynkkynen@iki.fi>
Link: https://lore.kernel.org/r/20200410123257.14559-1-tuomas.tynkkynen@iki.fi
[johannes: add note about length limit]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
