| Age | Commit message (Collapse) | Author |
|---|
|
An spi_driver does not need to set an owner, it will be populated by the
driver core.
Signed-off-by: Andrew F. Davis <afd@ti.com>
Acked-by: Jonathan Cameron <jic23@kernel.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Add the option to configure multiple 'scan plans' for scheduled scan.
Each 'scan plan' defines the number of scan cycles and the interval
between scans. The scan plans are executed in the order they were
configured. The last scan plan will always run infinitely and thus
defines only the interval between scans.
The maximum number of scan plans supported by the device and the
maximum number of iterations in a single scan plan are advertised
to userspace so it can configure the scan plans appropriately.
When scheduled scan results are received there is no way to know which
scan plan is being currently executed, so there is no way to know when
the next scan iteration will start. This is not a problem, however.
The scan start timestamp is only used for flushing old scan results,
and there is no difference between flushing all results received until
the end of the previous iteration or the start of the current one,
since no results will be received in between.
Signed-off-by: Avraham Stern <avraham.stern@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/kvalo/wireless-drivers-next
Kalle Valo says:
====================
Major changes:
iwlwifi
* some debugfs improvements
* fix signedness in beacon statistics
* deinline some functions to reduce size when device tracing is enabled
* filter beacons out in AP mode when no stations are associated
* deprecate firmwares version -12
* fix a runtime PM vs. legacy suspend race
* one-liner fix for a ToF bug
* clean-ups in the rx code
* small debugging improvement
* fix WoWLAN with new firmware versions
* more clean-ups towards multiple RX queues;
* some rate scaling fixes and improvements;
* some time-of-flight fixes;
* other generic improvements and clean-ups;
brcmfmac
* rework code dealing with multiple interfaces
* allow logging firmware console using debug level
* support for BCM4350, BCM4365, and BCM4366 PCIE devices
* fixed for legacy P2P and P2P device handling
* correct set and get tx-power
ath9k
* add support for Outside Context of a BSS (OCB) mode
mwifiex
* add USB multichannel feature
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Align fields reg_ch_conf_last and reg_ch_conf_pending of
struct wl1271{} to 64bit.
Without this, on 64bit ARM, wlcore_set_pending_regdomain_ch() fails at
the point it calls set_bit(ch_bit_idx, (long*)wl->reg_ch_conf_pending);
Here is the error message while doing iw wlan0 scan or connect:
[ 10.666857] wlcore: IRQ work
[ 10.670046] wlcore: intr: 0x40 (fw_rx_counter = 1, drv_rx_counter = 0, tx_results_counter = 0)
[ 10.678697] wlcore: WL1271_ACX_INTR_DATA
[ 10.682810] Unhandled fault: alignment fault (0x96000021) at 0xffffffc037a817f4
[ 10.690139] Internal error: : 96000021 [#1] PREEMPT SMP
[ 10.695366] Modules linked in:
[ 10.698437] CPU: 3 PID: 894 Comm: irq/60-wl18xx Tainted: G W 4.2.0-rc6-linaro-hikey #2
[ 10.707501] Hardware name: HiKey Development Board (DT)
[ 10.712733] task: ffffffc03a9d1680 ti: ffffffc039e18000 task.ti: ffffffc039e18000
[ 10.720239] PC is at set_bit+0x14/0x30
[ 10.724002] LR is at wlcore_set_pending_regdomain_ch+0x40/0x4c
Signed-off-by: Guodong Xu <guodong.xu@linaro.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
Fixes the output of 'modinfo --field firmware'.
Signed-off-by: Geoff Levand <geoff@infradead.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
Advertise the capability to send A-MSDU within A-MPDU
in the AddBA request sent by mac80211. Let the driver
know about the peer's capabilities.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
Add diversity statistics and sync the driver
statistics acx and debugfs representation
with the current fw api.
Signed-off-by: Guy Mishol <guym@ti.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
Sync the driver statistics acx and debugfs representation
with the current fw api.
Signed-off-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
When starting a p2p mgmt interface, enable its device role. This
allows us to keep the sta role disabled and scan on the dev role.
In general, p2p management interfaces cannot send vif-specific commands
to FW, as the vif role id is invalid. Only off-channel data and scans
happen on this vif, so most ops are not relevant.
If the vif is a p2p mgmt vif, block some mac80211 ops.
Configure rate policies for p2p mgmt interface, as
otherwise p2p packets come out with arbitrary rates.
Since wpa_supplicant currently doesn't support standalone
p2p device mode (without another attached managed interface),
add p2p device to the allowed interface combinations without
decreasing the allowed station count.
Moreover, increase the station count in some cases, as AP
mode usually starts as station interface, and the AP interface
is now different from the p2p management one).
Signed-off-by: Arik Nemtsov <arik@wizery.com>
Signed-off-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
Add definitions and function prototypes for generic_cfg
command.
Signed-off-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
Add support for long intervals on sched scan.
If configured, the original request interval will
be used num_short_interval times, and then the
long interval will be used.
While on it, fix the scan command field names
to reflect the expected value is in ms (rather
than secs).
These values will be taken from the conf file,
so bump its version accordingly.
Signed-off-by: Eyal Shapira <eyal@wizery.com>
Signed-off-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
Added support for a new time sync event
the event data contains the WiLink TSF value.
To trigger the event, a HW modification is required,
so as a supporting firmware binary.
Signed-off-by: Yaniv Machani <yanivma@ti.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
add comments to the antenna diversity reading
Signed-off-by: Guy Mishol <guym@ti.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
add option to dynamically configure the fw
which debug traces to open
Signed-off-by: Guy Mishol <guym@ti.com>
Signed-off-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
update the rssi reading on rx_status
to read both RSSI level (7 bits) and
antenna diversity (msb)
Signed-off-by: Guy Mishol <guym@ti.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
When wlcore_probe_of failed, return the correct error code instead of ENOMEM
Signed-off-by: Raphaël Poggi <poggi.raph@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/kvalo/wireless-drivers-next
Kalle Valo says:
====================
Major changes:
mwifiex:
* enhancements for AP mode: support verbose information in station
dump command and also information about AP link.
* enable power save by default
brcmfmac:
* fix module reload issue for PCIe
* improving msgbuf protocol for PCIe devices
* rework .get_station() cfg80211 callback operation
* determine interface combinations upon device feature support
ath9k:
* ath9k_htc: add support of channel switch
wil6210:
* add modparam for bcast ring size
* support hidden SSID
* add per-MCS Rx stats
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
As we're running out of hardware capability flags pretty quickly,
convert them to use the regular test_bit() style unsigned long
bitmaps.
This introduces a number of helper functions/macros to set and to
test the bits, along with new debugfs code.
The occurrences of an explicit __clear_bit() are intentional, the
drivers were never supposed to change their supported bits on the
fly. We should investigate changing this to be a per-frame flag.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
Delete jump to a label on the next line, when that label is not
used elsewhere.
A simplified version of the semantic patch that makes this change is as
follows: (http://coccinelle.lip6.fr/)
// <smpl>
@r@
identifier l;
@@
-if (...) goto l;
-l:
// </smpl>
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/kvalo/wireless-drivers-next
Kalle Valo says:
====================
ath10k:
* enable channel 144 on 5 GHz
* enable Adaptive Noise Immunity (ANI) by default
* add Wake on Wireless LAN (WOW) patterns support
* add basic Tunneled Direct Link Setup (TDLS) support
* add multi-channel support for QCA6174
* enable IBSS RSN support
* enable Bluetooth Coexistance whenever firmware supports it
* add more versatile way to set bitrates used by the firmware
ath9k:
* spectral scan: add support for multiple FFT frames per report
iwlwifi:
* major rework of the scan code (Luca)
* some work on the thermal code (Chaya Rachel)
* some work on the firwmare debugging infrastructure
brcmfmac:
* SDIO suspend and resume fixes
* wiphy band info and changes in regulatory settings
* add support for BCM4324 SDIO and BCM4358 PCIe
* enable support of PCIe devices on router platforms (Hante)
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/jberg/mac80211-next
Johannes Berg says:
====================
Lots of updates for net-next for this cycle. As usual, we have
a lot of small fixes and cleanups, the bigger items are:
* proper mac80211 rate control locking, to fix some random crashes
(this required changing other locking as well)
* mac80211 "fast-xmit", a mechanism to reduce, in most cases, the
amount of code we execute while going from ndo_start_xmit() to
the driver
* this also clears the way for properly supporting S/G and checksum
and segmentation offloads
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
If the wl18xx-conf.bin file is missing or invalid (e.g. due
to recent driver change), fallback to default configuration
instead of failing driver load.
Reported-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
* Interrupt request need to happen when the wilink chip is powered on and
driving the wlan_irq line. This avoids spurious interrupt issues that
are a result of different external pulls configuration on different
platforms
* Allow working with wl18xx level-low and falling edge irqs by configuring
wl18xx to invert the device interrupt
Signed-off-by: Eyal Reizer <eyalr@ti.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
This support is essentially useless as typically networks are encrypted,
frames will be filtered by hardware, and rate scaling will be done with
the intended recipient in mind. For real monitoring of the network, the
monitor mode support should be used instead.
Removing it removes a lot of corner cases.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM DT updates from Olof Johansson:
"As always, this tends to be one of our bigger branches. There are
lots of updates this release, but not that many jumps out as something
that needs more detailed coverage. Some of the highlights are:
- DTs for the new Annapurna Labs Alpine platform
- more graphics DT pieces falling into place on Exynos, bridges,
clocks.
- plenty of DT updates for Qualcomm platforms for various IP blocks
- some churn on Tegra due to switch-over to tool-generated pinctrl
data
- misc fixes and updates for Atmel at91 platforms
- various DT updates to add IP block support on Broadcom's Cygnus
platforms
- more updates for Renesas platforms as DT support is added for
various IP blocks (IPMMU, display, audio, etc)"
* tag 'armsoc-dt' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (231 commits)
ARM: dts: alpine: add internal pci
Revert "ARM: dts: mt8135: Add pinctrl/GPIO/EINT node for mt8135."
ARM: mvebu: use 0xf1000000 as internal registers on Armada 370 DB
ARM: dts: qcom: Add idle state device nodes for 8064
ARM: dts: qcom: Add idle states device nodes for 8084
ARM: dts: qcom: Add idle states device nodes for 8974/8074
ARM: dts: qcom: Update power-controller device node for 8064 Krait CPUs
ARM: dts: qcom: Add power-controller device node for 8084 Krait CPUs
ARM: dts: qcom: Add power-controller device node for 8074 Krait CPUs
devicetree: bindings: Document qcom,idle-states
devicetree: bindings: Update qcom,saw2 node bindings
dt-bindings: Add #defines for MSM8916 clocks and resets
arm: dts: qcom: Add LPASS Audio HW to IPQ8064 device tree
arm: dts: qcom: Add APQ8084 chipset SPMI PMIC's nodes
arm: dts: qcom: Add 8x74 chipset SPMI PMIC's nodes
arm: dts: qcom: Add SPMI PMIC Arbiter nodes for APQ8084 and MSM8974
arm: dts: qcom: Add LCC nodes
arm: dts: qcom: Add TCSR support for MSM8960
arm: dts: qcom: Add TCSR support for MSM8660
arm: dts: qcom: Add TCSR support for IPQ8064
...
|
|
The driver can clearly enable fast-xmit since it does rate
control in the device and thus must do duration calculation
there as well.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
This patch fix a spelling typo in MODULE_DESCRIPTION in
wl1251/main.c
Signed-off-by: Masanari Iida <standby24x7@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/kvalo/wireless-drivers-next
Kalle Valo says:
====================
Major changes:
ath9k:
* add Active Interference Cancellation, a method implemented in the HW
to counter WLAN RX > sensitivity degradation when BT is transmitting
at the same time. This feature is supported by cards like WB222
based on AR9462.
iwlwifi:
* Location Aware Regulatory was added by Arik
* 8000 device family work
* update to the BT Coex firmware API
brmcfmac:
* add new BCM43455 and BCM43457 SDIO device support
* add new BCM43430 SDIO device support
wil6210:
* take care of AP bridging
* fix NAPI behavior
* found approach to achieve 4*n+2 alignment of Rx frames
rt2x00:
* add new rt2800usb device DWA 130
rtlwifi:
* add USB ID for D-Link DWA-131
* add USB ID ASUS N10 WiFi dongle
mwifiex:
* throughput enhancements
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/jberg/mac80211-next
Johannes Berg says:
====================
Lots of updates for net-next; along with the usual flurry
of small fixes, cleanups and internal features we have:
* VHT support for TDLS and IBSS (conditional on drivers though)
* first TX performance improvements (the biggest will come later)
* many suspend/resume (race) fixes
* name_assign_type support from Tom Gundersen
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Now that we have wlcore device-tree bindings in place
(for both wl12xx and wl18xx), remove the legacy
wl12xx_platform_data struct, and move its members
into the platform device data (that is passed to wlcore)
Davinci 850 is the only platform that still set
the platform data in the legacy way (and doesn't
have DT bindings), so remove the relevant
code/Kconfig option from the board file (as suggested
by Sekhar Nori)
Since no one currently uses wlcore_spi, simply remove its
platform data support (DT bindings will have to be added
if someone actually needs it)
Signed-off-by: Luciano Coelho <luca@coelho.fi>
Signed-off-by: Eliad Peller <eliad@wizery.com>
Tested-by: Nikita Kiryanov <nikita@compulab.co.il>
Acked-by: Kalle Valo <kvalo@codeaurora.org>
Acked-by: Sekhar Nori <nsekhar@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
When running with device-tree, we no longer have a board file
that can set up the platform data for wlcore.
Allow this data to be passed from DT.
Signed-off-by: Ido Yariv <ido@wizery.com>
Signed-off-by: Eliad Peller <eliad@wizery.com>
Tested-by: Sébastien Szymanski <sebastien.szymanski@armadeus.com>
Tested-by: Nikita Kiryanov <nikita@compulab.co.il>
Acked-by: Kalle Valo <kvalo@codeaurora.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
Instead of defining an enumeration with the FW specific values for the
different clock rates, use the actual frequency instead. Also add a
boolean to specify whether the clock is XTAL or not.
Change all board files to reflect this.
Signed-off-by: Luciano Coelho <luca@coelho.fi>
[Eliad - small fixes, update board file changes]
Signed-off-by: Eliad Peller <eliad@wizery.com>
Tested-by: Nikita Kiryanov <nikita@compulab.co.il>
Acked-by: Kalle Valo <kvalo@codeaurora.org>
Acked-by: Sekhar Nori <nsekhar@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
The platform_quirk element in the platform data was used
to change the way the IRQ is triggered. When set,
the EDGE_IRQ quirk would change the irqflags used
and treat edge trigger differently from the rest.
Instead of hiding this irq flag setting behind the quirk,
have the board files set the irq_trigger explicitly.
This will allow us to use standard irq DT definitions
later on.
Signed-off-by: Luciano Coelho <luca@coelho.fi>
[Eliad - rebase, add irq_trigger field and pass it,
update board file changes]
Signed-off-by: Eliad Peller <eliad@wizery.com>
Tested-by: Nikita Kiryanov <nikita@compulab.co.il>
Acked-by: Kalle Valo <kvalo@codeaurora.org>
Acked-by: Sekhar Nori <nsekhar@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
In struct wl18xx_acx_rx_rate_stat, rx_frames_per_rates field is an
array, not a number. This means WL18XX_DEBUGFS_FWSTATS_FILE can't be
used to display this field in debugfs (it would display a pointer, not
the actual data). Use WL18XX_DEBUGFS_FWSTATS_FILE_ARRAY instead.
This bug has been found by adding a __printf attribute to
wl1271_format_buffer. gcc complained about "format '%u' expects
argument of type 'unsigned int', but argument 5 has type 'u32 *'".
Fixes: c5d94169e818 ("wl18xx: use new fw stats structures")
Signed-off-by: Nicolas Iooss <nicolas.iooss_linux@m4x.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
Use the built-in function instead of memset.
Miscellanea:
Add #include <linux/etherdevice.h> where appropriate
Use ETH_ALEN instead of 6
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This modifies cfg80211_vendor_event_alloc() with an additional argument
struct wireless_dev *wdev. __cfg80211_alloc_event_skb() is modified to
take in *wdev argument, if wdev != NULL, both the NL80211_ATTR_IFINDEX
and wdev identifier are added to the vendor event.
These changes make it easier for drivers to add ifindex indication in
vendor events cleanly.
This also updates all existing users of cfg80211_vendor_event_alloc()
and __cfg80211_alloc_event_skb() in the kernel tree.
Signed-off-by: Ahmad Kholaif <akholaif@qca.qualcomm.com>
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
We recently introduced a new error path which needs an unlock.
Fixes: 6d5a748d4836 ('wlcore: add ability to reduce FW interrupts during suspend')
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
Signed-off-by: Giel van Schijndel <me@mortis.eu>
Reported-at: http://www.viva64.com/en/b/0299/
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
Patch "ath9k: Fix no-ack frame status" needs these mac80211 patches:
commit 5cf16616e152dd5c274a65954c77f64892d025a8
Author: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Date: Wed Dec 10 21:26:11 2014 +0530
mac80211: Fix accounting of multicast frames
commit 6b127c71fbdd3daacfd8b9f80b8e6ebfb70a889e
Author: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Date: Wed Dec 10 21:26:10 2014 +0530
mac80211: Move IEEE80211_TX_CTL_PS_RESPONSE
Conflicts:
drivers/net/wireless/ath/wil6210/cfg80211.c
drivers/staging/rtl8723au/os_dep/ioctl_cfg80211.c
|
|
After having all the dfs infrastructure in place, declare
radar_detect_widths support for the ap interfaces combination.
Signed-off-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
Add dfs region to the reg domain channel update command.
Signed-off-by: Guy Mishol <guym@ti.com>
Signed-off-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
Since we are going to support dfs channels, there
is no reason to mark them as NO_IR (having
the DFS flag is enough anyway).
Additionally, when setting the regdomain configuration,
enable usable dfs channels.
Signed-off-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
call wlcore_cmd_dfs_master_restart when starting
the ap on a new channel (after csa is done).
Add a new WLVIF_FLAG_BEACON_DISABLED flag to
indicate that dfs_master_restart command
is required.
Signed-off-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
Support ap csa support by implementing the channel_switch_beacon()
mac80211 op.
Signed-off-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
Add debugfs file to emulate radar detection through
a special fw cmd (which in turn will generate radar
event)
Signed-off-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
Add support for CAC start/stop commands, and pass
radar detection events from the fw to mac80211.
Bump fw name (to wl18xx-fw-4.bin) and min fw version
(to 8.9.*.*.11), and align event mailbox accordingly.
Signed-off-by: Guy Mishol <guym@ti.com>
Signed-off-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
Enable ELP authorization in AP mode and enable the use
of the wakeup bit in the ELP register.
Introduce AP role sleep configuration which is disabled
by default. When configured, it allows the AP to sleep
when ELP is authorized for it.
Signed-off-by: Kobi Leibovitch <kobi.lev100@gmail.com>
Signed-off-by: Arik Nemtsov <arik@wizery.com>
Signed-off-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
configure wowlan when host is suspended in AP mode,
since the FW can now wake the host up on Rx.
Signed-off-by: Kobi Leibovitch <kobi.lev100@gmail.com>
Signed-off-by: Arik Nemtsov <arik@wizery.com>
Signed-off-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
Add the ability to mask FW interrupts on RX BA activity, PSM
entry/exit and fast-link notifications. This is used when the host
is suspended in order to decrease redundant wake ups.
Signed-off-by: Ram Amrani <ramrani@ti.com>
Signed-off-by: Arik Nemtsov <arik@wizery.com>
Signed-off-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
sta_rc_update runs in atomic context. thus, a new work
should be scheduled in order to configure the fw
with the required configuration.
Signed-off-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
